Kenwood KMR-D772BT, KDC-X502, KDC-BT772HD, KDC-BT572U, KDC-X702 User Manual

KDC-X702

KDC-X502

KDC-BT772HD

KDC-BT572U

KMR-D772BT

CD-RECEIVER

INSTRUCTION MANUAL

AMPLI-TUNER LECTEUR DE CD

MODE D’EMPLOI

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KDC-X702/KDC-BT772HD/KMR-D772BT/KDC-X502/KDC-BT572U Serial number

US Residents Only

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.

JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN

THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.

Location : Top Plate

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.

Informação sobre a eliminação de pilhas

Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador. A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.

CALIFORNIA, USA ONLY

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

IC (Industry Canada) Notice

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired

operation of the device.

CAUTION

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body.

Note de IC (Industrie Canada)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le fonctionnement.

(For / / ) Contains Bluetooth Module FCC ID: ZWY8350X

IC ID: 12033A-8350X

(For Contains Bluetooth Module FCC ID: ZWY8811X

IC ID: 12033A-8811X

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

/ )

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée comme conforme sans évaluation de l’exposition maximale autorisée (MPE). Cependant, il est souhaitable qu’il devrait être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain.

Para cumplimiento de la IFT:

“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su

operación no deseada”

SOFTWARE LICENSE AGREEMENT

Article 3 Conditions for Grant of License

The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software.

The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement. This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the Product in which the "Licensed Software" is embedded.

The Licensed Software may include the software which has been licensed to the Licensor directly or indirectly from any third party. In such case, some third parties require the Users to follow their conditions for use separately from this Software License Agreement. Such software shall not be subject to this Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided separately below.

Article 1 General Provision

The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User. (the country where the User bought the Product(hereinafter the "Country")

Article 2 License

1. The license granted under this Agreement shall be the right to use the Licensed Software in the Product.

2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed Software and any related documents, whether in whole or in part.

3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.

4. The User shall use the Licensed Software according to the directions described in the operation manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright Law or any other laws and regulations by applying whole or a part of the Licensed Software.

1. When the User transfers the Product, it may also transfer the license to use the Licensed Software embedded in the Product (including any related materials, updates and upgrades) on condition that no original, copies or related materials continue in the possession of the User, and that the User shall cause the transferee to comply with this Software License Agreement.

2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code analysis works in connection with the Licensed Software.

Article 4 Right pertaining to the Licensed Software

Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.

Article 5 Indemnification of Licensor

1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User or any third party due to the exercise of the license granted to the User under this Agreement, unless otherwise restricted by law.

2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with certain objective of the Licensed Software.

Article 6 Liability to Third Party

If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any other intellectual property right that was caused by the User's use of the Licensed Software, the User shall settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any inconvenience it may cause.

Article 7 Confidentiality

iii

The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof or any other information to be granted under this Agreement, as well as the conditions of this Agreement as has not yet entered the public domain, and shall not disclose or divulge the same to any third party without approval of the Licensor.

Article 8 Termination

Important Notice concerning the Software

In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event: (1) when the User violated any provision of this Agreement; or (2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software

If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination.

Article 10 Protection of Copyright

1. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.

2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights.

Article 11 Export Restriction

1. It is prohibited to export the Licensed Software and any related documents outside the country of the User (including transmission thereof outside the country of the User via Internet of other communication tools).

2. The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of User and any other countries.

3. The User shall agree that the software will be subject to any and all applicable international and domestic laws (including the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users, the use by end-users and importing countries to be provided by the country of User and any other countries, and any other governmental authorities).

-jansson

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Article 12 Miscellaneous

1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force.

2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be provided or settled upon good-faith consultation between the Licensor and the User.

3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from, and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.

CONTENTS

BEFORE USE

BEFORE USE 2

BASICS 3

GETTING STARTED 4

1 Select the display language

and cancel the demonstration 2 Set the clock and date 3 Set the initial settings

HD RadioTM tuner 6

RADIO 8

CD/USB/iPod/ANDROID 10

AUX 13

Pandora® 13

iHeartRadio® 15

Spotify 16

SiriusXM® Radio 17

BLUETOOTH® 20

AUDIO SETTINGS 29

DISPLAY SETTINGS 32

TROUBLESHOOTING 33

REFERENCES 36

Maintenance More information

IMPORTANT

•

To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe

Warning and Caution in this manual.

•

Please keep the manual in a safe and accessible place for future reference.

WARNING

• Do not operate any function that takes your attention away from safe driving.

• Do not ingest the battery, Chemical Burn Hazard

The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Caution

Volume setting:

•

Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•

Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•

Avoid using the external device if it might hinder safe driving.

•

Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•

Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

•

If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

•

USB rating for the USB cables from the rear of the unit is indicated on a label.

•

Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire

connected

Remote control (RC-406):

•

Do not leave the remote control in hot places such as on the dashboard.

•

The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•

The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

( 41)

. Turn off the unit or change the source to STANDBY when parking at a low ceiling area.

( 42)

INSTALLATION/ CONNECTION 39

SPECIFICATIONS 43

ENGLISH

How to read this manual

•

Operations are explained mainly using buttons on the faceplate of .

•

English indications are used for the purpose of explanation. You can select the display language from the

• [XX]

indicates the selected items.

• ( XX)

indicates references are available on the stated page.

[FUNCTION]

menu.

( 5)

BASICS

Faceplate

Attach

Display windowVolume knob

Lights up when Bluetooth connection is established.

( 21)

Detach

Detach button

Note: The highlighted area on the faceplate flashes when the unit enters searching status.

To On the faceplate

Turn on the power

Adjust the volume Turn the volume knob.

Select a source

Change the display information Press DISP repeatedly.

For : The power will automatically turn off after 20minutes when in standby mode (Auto Power Off).

Auxiliary cable from the rear of the unit.

USB 1 cable from the rear of the unit.

(For USB 2 cable from the rear of the unit.

Press

• Press and hold to turn off the power.

Press

/ / )

repeatedly.

( 38, 39)

How to reset

Reset the unit within 5seconds after detaching the faceplate.

ENGLISH

BASICS

Remote control (RC-406)

This unit can be remotely controlled with an optionally purchased remote control.

Remote sensor (Do not expose to bright sunlight.)

GETTING STARTED

Select the display language and cancel the demonstration

Pull out the insulation sheet when using for the first time.

: Remote control functions are not available.

How to replace the battery

To On the remote control

Turn on the power Press and hold SRC to turn off the power.

( Pressing SRC does not turn on the power. )

Adjust the volume Press

• Press and hold the volume to 15.

Press ATT during playback to attenuate the sound.

• Press again to cancel.

or .

to continuously increase

When you turn on the power for the first time (or

[YES], 5

KNOB”

1 Turn the volume knob to select

Then, (except for

), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME

[ENG]

(English) or

then press the knob.

[ENG]

is selected for the initial setup.

) the display shows: “CANCEL DEMO”

“PRESS” “VOLUME KNOB”.

[FACTORY RESET]

[SPA]

(Spanish),

is set to

2 Press the volume knob.

[YES]

is selected for the initial setup.

3 Press the volume knob again.

“DEMO OFF” appears.

Set the clock and date

Press the volume knob to enter

2 Turn the volume knob to select

To adjust the clock

3 Turn the volume knob to select

[FUNCTION] [CLOCK]

[CLOCK ADJUST]

, then press the knob.

4 Turn the volume knob to make the settings, then press the knob.

Hour

5 Turn the volume knob to select 6 Turn the volume knob to select

Minute

[CLOCK FORMAT] [12H]

[24H]

, then press the knob.

Select a source Press SRC repeatedly.

ENGLISH

GETTING STARTED

To set the date

7 Turn the volume knob to select 8 Turn the volume knob to select

the knob.

9 Turn the volume knob to select

[DATE FORMAT] [DD/MM/YY]

[DATE SET]

, then press the knob.

[MM/DD/YY]

, then press

10 Turn the volume knob to make the settings, then press the knob.

Day

Month Year or Month Day Year

11 Press and hold to exit.

To return to the previous setting item, press

Set the initial settings

Press repeatedly to enter STANDBY.

2 Press the volume knob to enter

[FUNCTION]

3 Turn the volume knob to select an item (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press

DISPLAY

EASY MENU

TUNER SETTING

When entering

:LCD DISPLAY zone illumination changes to white color.;

OFF

:LCD DISPLAY zone illumination remains as

( 32)

•

KEY zone illumination changes to light blue color when you enter

[FUNCTION]

•

Refer to the illustration on page 32 for zone identification.

[FUNCTION]

, irregardless of the

...

[EASY MENU]

[COLOR SELECT]

setting.

Default:

color.

SYSTEM

KEY BEEP

SOURCE SELECT

PANDORA SRC

IHEART SRC

SPOTIFY SRC

BUILT-IN AUX

CD READ

F/W UPDATE

UPDATE SYSTEM/UPDATE HD

F/W UPDATE xxxx/ F/W UPDATE Vxx

FACTORY RESET YES

CLOCK

CLOCK DISPLAY

:Activates the keypress tone.;

:Enables PANDORA 1/PANDORA 2/PANDORA in source selection.;

OFF

:Disables.

:Enables IHEARTRADIO 1/IHEARTRADIO 2/IHEARTRADIO in source

selection.;

:Enables SPOTIFY 1/SPOTIFY 2/SPOTIFY in source selection.;

OFF

:Disables.

:Enables AUX in source selection.;

: Automatically distinguishes between audio file disc and music CD. ;

: Forces to play as a music CD. No sound can be heard if an audio file disc

is played.

YES

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated). For details on how to update the firmware, visit <www.kenwood.com/cs/ce/>.

:Resets the settings to default (except the stored station).;

:Cancels.

(Except for )

:The clock time is shown on the display even when the unit is turned

off.;

OFF

( 13)

OFF

:Disables.

( 16)

(for / )

:Cancels.

( 15)

OFF

:Deactivates.

OFF

:Disables.

( 13)

PRESET TYPE

NORMAL

(FM1/FM2/FM3/AM).; for each preset button, regardless of the selected band or SiriusXM channel.

:Memorizes one station for each preset button in each band

MIX

:Memorizes one station or SiriusXM channel

ENGLISH

ESPANOL

Select the display language for if applicable. By default,

[ENGLISH]

is selected.

[FUNCTION]

menu and music information

ENGLISH

GETTING STARTED

HD Radio™ tuner

(for / )

Applicable only when you connect Kenwood Marine Remote Control unit (KCA-RC55MR, optional accessory) to this unit.

• For connection,

• Refer also to the supplied instruction manual of the Kenwood Marine Remote Control unit for more information.

Preparation:

Press to enter

repeatedly to enter STANDBY, then press the volume knob

[FUNCTION].

42, Connecting external components

(for )

1 Turn the volume knob to select an item, then press the knob.

[SYSTEM]

Remote control ID list is displayed.

•

2 Turn the volume knob to select an available ID

[REMOTE ID2]/[REMOTE ID3]

“REGISTERING” appears on the display window.

To register, on the Kenwood Marine Remote Control unit:

• Press ENTER to register as

• Press SRC to register as

• Press DISP to register as

Once the ID is registered, “COMPLETED” appears.

To delete the registered ID



[REMOTE SETTING]

[YES]

indicates that this ID is already registered.

[NO]

indicates that this ID is available.



[REMOTE ID SET]

, then press the knob

[REMOTE ID1]

[REMOTE ID2]

[REMOTE ID3]

[REMOTE ID1]

1 Turn the volume knob to select an item, then press the knob.

[SYSTEM]

2 Turn the volume knob to select the ID to delete [

[

ID2 DELETE]/[ID3 DELETE]

3 Turn the volume knob to select

select



[REMOTE SETTING]

[NO]

to cancel.



[REMOTE ID DELETE]

, then press the knob.

[YES]

to delete the selected ID, and

ID1 DELETE]

You can tune in to both conventional and HD Radio broadcasts.

• To find HD Radio stations in your area, visit <http://www.hdradio.com>.

Search for a station

Press repeatedly to select HD RADIO.

2 Press repeatedly (or press / on the remote

control) to select FM1/FM2/FM3/AM.

3 Press S/T (or press S/ on the remote control) to

search for a station or channel.

• To change the searching method for S/T: Press

repeatedly. AUTO1 : Automatically search for a station or channel. AUTO2 : Search for a preset station or channel. MANUAL : Manually search for a station or channel.

• To store a station or channel: Press and hold one of the number

buttons (1to6).

• To select a stored station or channel: Press one of the number buttons

(1to6) (or press one of the number buttons (1to6) on the remote

control).

• To exit, press and hold

• To return to the previous setting item, press

ENGLISH

HD Radio™ tuner

(for / )

Direct Access Tuning

(using the remote control)

1 Press DIRECT to enter Direct Access Tuning. 2 Press the number buttons to enter a frequency. 3 Press to search for a station or channel.

• To cancel, press

• If no operation is done for 10seconds after step is automatically canceled.

or DIRECT.

2, Direct Access Tuning

Select an HD Radio multicast channel

Many HD Radio stations offer more than one channel programming. This service is called multicasting. While receiving HD Radio multicast

channels....

Press S/T to select your desired channel (HD1 to HD8).

“LINKING” appears while linking to a multicast channel.

Receive an Emergency Alert message

You can receive an emergency alert message while listening to another source or while in STANDBY, via HD Radio Broadcast.

Activate emergency alert message reception

Press the volume knob to enter

1 2 Turn the volume knob to select 3

Turn the volume knob to select

4 Turn the volume knob to select

[FUNCTION] [TUNER SETTING]

[EMERGENCY ALERT], then press the knob.

[ON]

, then press the knob.

5 Press and hold to exit.

Receive an emergency alert message

When an emergency alert message is received, it appears and remains on the display until the user performs the “Ignore” function.

• Press message. The same emergency alert message will not interrupt again for 12 hours.

(or press SRC on the remote control) to ignore the alert

Display received emergency alert messages

The received emergency alert messages are stored in the Alert Message List, and you can check them later. While listening to the HD RADIO source...

1 Press to display the Alert Message List. 2 Turn the volume knob to select a message. 3 Press the volume knob to display the information related to the

message.

4 Press again to exit.

• “NO LIST” appears when the list is empty.

• This feature can store up to four messages in the list.

• To clear the message list, set

[FACTORY RESET]

[YES]. ( 5)

Other settings

Press the volume knob to enter

2 Turn the volume knob to select an item

[FUNCTION]

( 8)

, then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press

• To deactivate emergency alert message reception, select

• To return to the previous setting item, press

[OFF]

in step 4.

ENGLISH

HD Radio™ tuner

(for / )

RADIO

(for / / )

TUNER SETTING

IF BAND

AUTO MEMORY YES

RECEIVE MODE

CLOCK

TIME SYNC

AUTO

adjacent FM stations. (Stereo effect may be lost.); interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.

•

Selectable only if

Sets the receive mode of the HD Radio receiver.

AUTO

broadcast.; in to analog broadcast only.

station time.;

Default:

:Increases the tuner selectivity to reduce interference noises from

WIDE

:Subjects to

:Automatically starts memorizing 6 stations with good reception.;

:Cancels.

[NORMAL]

:Automatically tunes to analog broadcast when there is no digital

DIGITAL

:Synchronizes the unit’s time to the Radio Broadcast Data System

:Tunes in to digital broadcast only.;

OFF

:Cancels.

is selected for

[PRESET TYPE]. ( 5)

ANALOG

:Tunes

Search for a station

Press repeatedly to select RADIO.

2 Press repeatedly (or press / on the remote

control) to select FM1/FM2/FM3/AM.

3 Press S/T (or press S/ on the remote control) to

search for a station.

• To change the searching method for S/T: Press repeatedly.

AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

• To store a station: Press and hold one of the number buttons (1to6).

• To select a stored station: Press one of the number buttons (1to6) (or press one of the number buttons (1to6) on the remote control).

Direct Access Tuning

(using the remote control)

1 Press DIRECT to enter Direct Access Tuning. 2 Press the number buttons to enter a frequency. 3 Press to search for a station.

• To cancel, press

• If no operation is done for 10seconds after step is automatically canceled.

ENGLISH

or DIRECT.

2, Direct Access Tuning

RADIO

(for / / )

Other settings

Press the volume knob to enter

Turn the volume knob to select an item (see the following table), then press the knob.

[FUNCTION]

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press

TUNER SETTING

AUTO MEMORY

MONO SET

TI ON

PTY SEARCH

YES

:Automatically starts memorizing 6 stations with good reception.;

:Cancels.

•

Selectable only if

:Improves the FM reception, but the stereo effect may be lost.;

OFF

:Cancels.

:Allows the unit to temporarily switch to Traffic Information if

available (“TI” lights up).;

Select the available Program Type (see the following), then press

/T to start.

[NORMAL]

OFF

is selected for

:Cancels.

Default:

[PRESET TYPE]. ( 5)

Available Program Type for

SPEECH

MUSIC

The unit will search for the Program Type categorized under [SPEECH]

[MUSIC]

•

[MONO SET]/[TI]/[PTY SEARCH]

FM2/FM3.

• If the volume is adjusted during reception of traffic information, the adjusted volume is memorized automatically. It will be applied the next time traffic information is turned on.

NEWS, INFORM

(religious talk), (spanish talk),

ROCK, CLS ROCK

(softrock),

JAZZ, CLASSICL

(soft rhythm and blues), (spanish music),

if selected.

(information),

WEATHER

(classic rock),

TOP 40, COUNTRY, OLDIES, SOFT, NOSTALGA

(classical),

[PTY SEARCH]

SPORTS, TALK, LANGUAGE, REL TALK

PERSNLTY

HIP HOP

(personality),

ADLT HIT

R & B

(rhythm and blues),

REL MUSC

is selectable only when the band is FM1/

PUBLIC, COLLEGE, HABL ESP

(adult hits),

(religious music),

SOFT RCK

(nostalgia),

SOFT R&B

MUSC ESP

CLOCK

TIME SYNC

:Synchronizes the unit’s time to the Radio Broadcast Data System

station time.;

OFF

:Cancels.

ENGLISH

CD/USB/iPod/ANDROID

Start playback

The source changes automatically and playback starts.

Label side

USB 1 cable from the rear of the unit (USB input terminal).

: You can also connect to the USB 2 cable from the rear of the unit (USB input terminal).

Eject disc

USB

CA-U1EX (max.: 500mA) (optional accessory)

iPod/iPhone

KCA-iP102/KCA-iP103 (optional accessory) or accessory of the iPod/

iPhone

ANDROID

USB cable (commercially available)

Selectable source:

•

/ / : CD/USB 1/USB 2/iPod 1/iPod 2/ANDROID 1/

ANDROID 2

•

/ : CD/USB/iPod USB/ANDROID

To On the faceplate On the remote control

Playback/pause Press .

Reverse/Fast-forward

Select a track/file

Select a folder

Repeat play

Press and hold S/T. Press and hold S/ .

Press S/T. Press S/

Press J/K.

Press repeatedly.

TRACK REPEAT/ALL REPEAT FILE REPEAT/FOLDER REPEAT/ALL REPEAT

Press

: Audio CD

: MP3/WMA/AAC/WAV/

/ .

FLAC file

Random play

FILE REPEAT/FOLDER REPEAT/REPEAT OFF

Press repeatedly.

DISC RANDOM/RANDOM OFF FOLDER RANDOM/RANDOM OFF

: Audio CD

: MP3/WMA/AAC/WAV/FLAC file,

: iPod or ANDROID

iPod or ANDROID

Press and hold

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the

to select

ALL RANDOM

instructions to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

ENGLISH

CD/USB/iPod/ANDROID

For ANDROID: Applicable only when

For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.

For iPod/ANDROID: Applicable only when

For CD: Only for MP3/WMA/AAC files.

[BROWSE MODE]

[MODE OFF]/[BROWSE MODE]

is selected.

Select a file from a folder/list

For iPod/ANDROID, applicable only when selected.

[MODE OFF]/[BROWSE MODE]

Select control mode

While in iPod 1/iPod 2/iPodUSB source, press 5 repeatedly.

MODE ON

MODE OFF

While in ANDROID 1/ANDROID 2/ANDROID source, press 5 repeatedly.

BROWSE MODE

HAND MODE

: Control iPod using the iPod itself. However, you can still play/

pause, file skip, fast-forward or reverse from this unit.

: Control iPod from this unit.

: Control Android device from this unit via KENWOOD

MUSIC PLAY application installed in the Android device.

: Control Android device using the Android device itself via

other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

Select music drive

While in USB 1/USB 2/USB source, press 5 repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage

Class).

• Selected drive of a multiple drives device.

Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

1 Press . 2 Turn the volume knob to select a folder/list, then press the knob. 3 Turn the volume knob to select a file, then press the knob.

Quick Search

ANDROID 2 and ANDROID source)

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

Skip Search

ANDROID 2 and ANDROID source)

Press S/T to search at a preset skip search ratio.

[SKIP SEARCH])

• Pressing and holding S/T searches at a 10% ratio.

Alphabet search

ANDROID 1, ANDROID 2 and ANDROID source)

You can search for a file according to the first character.

For iPod 1/iPod 2/iPod USB source

(applicable only for CD, USB 1, USB 2, USB, ANDROID 1,

(applicable only for iPod 1, iPod 2, iPod USB, ANDROID 1,

( 12,

(applicable only for iPod 1, iPod 2, iPod USB,

1 Turn the volume knob quickly to enter character search. 2 Turn the volume knob to select the character.

• Select “

” to search for a character other than AtoZ, 0to9.

3 Press S/T to move to the entry position.

• You can enter up to 3characters. 4 Press the volume knob to start searching.

ENGLISH

CD/USB/iPod/ANDROID

For ANDROID 1/ANDROID 2/ANDROID source

1 Press J/K to enter character search. 2 Turn the volume knob to select the character.

^A^: Upper case letters (A to Z) _A_: Lower case letters (a to z)

-0-: Numbers (0 to 9) : Character other than AtoZ, 0to9

***

3 Press the volume knob to start searching.

• To return to the root folder/first file/top menu, press 5.

BT AUDIO source.)

• To return to the previous setting item, press .

• To cancel, press and hold

Direct Music Search

(using the remote control)

(Not applicable for

1 Press DIRECT. 2 Press the number buttons to enter a track/file number. 3 Press to search for music.

• To cancel, press

• Not available if Random Play is selected.

• Not applicable for iPod 1, iPod 2, iPodUSB, ANDROID 1, ANDROID 2 and ANDROID source.

or DIRECT.

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press

USB

MUSIC DRIVE DRIVE CHANGE

automatically and playback starts. Repeat steps

SKIP SEARCH 0.5%/1%/5%/10%

ANDROID1, ANDROID2 or ANDROID source, selects the skip search ratio over the total files.

:The next drive (

to 3 to select the following drives.

: While listening to iPod 1, iPod 2, iPodUSB,

[DRIVE 1]

[DRIVE 4]

Default:

) is selected

Settings to use KENWOOD Remote application

KENWOOD Remote application is designed to control the KENWOOD car receiver’s operations from the iPhone/iPod (via USB input terminal).

Preparation:

Install the latest version of KENWOOD Remote application on your device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

You can make the settings in the same way as connection via Bluetooth.

( 27)

ENGLISH

+ 36 hidden pages