Karcher HDS4-5-22-4MEa User Manual [en, es, fr]
HDS 3.5/23-4M Eg
HDS 3.5/30-4M Ea
HDS 4.0/20-4M Ea
HDS 4.5/22-4M Ea
English 6
Français 22
Español 40
Register and win!
www.kaercher.com
59661680 02/13
1
24 25 26 27 28 1
23
22
21
20
19
18
17
16
2
3
4
5
6
14 15
13
12
9911
2
10
8
7
29
MAX MIN
30
34
MAX
MIN
39
31 32
33
35
36
37
38
3
2
2.
1.
2
3
D
2000
3700
2500
3500
250
3000
1
200
4567
A
C
3
5
B
4
6
2.
5.
4.
2.
1.
3.
4
7
6.
7.
8
9.
9
8.
5
IMPORTANT SAFETY INSTRUCTIONS
몇 WARNING
When using this product basic precautions
should always be followed, including the
following:
1 Read all the instructions before using
the product.
2 High pressure jets can be dangerous if
misused. The jet must not be directed at
persons, animals, electrical devices, or
the unit itself.
3 To reduce the risk of injury, close super-
vision is necessary when a product is
used near children.
4 Know how to stop the product and
bleed pressures quickly. Be thoroughly
familiar with the controls.
5 Stay alert – watch what you are doing.
6 Wear safety goggles.
7 Do not use acids, alkaline, solvents, or
any flammable material in this product.
These products can cause physical in-
juries to the operator and irreversible
damage to the machine.
8 Do not operate the product when fa-
tigued or under the influence of alcohol
or drugs.
9 Do not overreach or stand on unstable
support. Keep good footing and bal-
ance at all times.
10 To reduce the risk of electrocution,
keep all connections dry and off the
ground. Do not touch plug with wet
hands.
11 The Trigger Gun Safety Lock prevents
the trigger from accidentally being en-
gaged. This safety feature DOES NOT
lock trigger in the ON position.
12 Keep operating area clear of all per-
sons.
13 Close cover before operating the ma-
chine.
14 This appliance is intended for commer-
cial use.
15 Follow the maintenance instructions
specified in the manual.
16 This machine has been designed for
use with cleaning chemicals supplied or
recommended by the manufacturer.
The use of other cleaning chemicals
may affect the operation of the machine
and void the warranty.
17 This product is provided with a Ground
Fault Circuit Interrupter built into the
power cord plug. If replacement of the
plug or cord is needed, use only identical replacement parts.
18 Do not use extension cord with this
product.
– Injection hazard: equipment can cause
serious injury if the spray penetrates the
skin. Do not point the gun at anyone or
any part of the body. In case of penetration seek medical aid immediately.
– This system is capable of producing
2300 psi/15.9 MPa (HDS 3.5/23) 3000 psi/20.7 MPa (HDS 3.5/30) 2000 psi/13.8 MPa (HDS 4.0/20) 2250 psi/15.5 MPa (HDS 4.5/22).
To avoid rupture and injury, do not operate this pump with components rated
less than 2300 psi/15.9 MPa (HDS 3.5/
23) - 3000 psi/20.7 MPa (HDS 3.5/30) 2000 psi/13.8 MPa (HDS 4.0/20) 2250 psi/15.5 MPa (HDS 4.5/22) working pressure (including but not limited to
spray guns, hose and hose connections).
– Before servicing, cleaning, or removal
of any part, shut off power and relieve
pressure.
– Do not spray electrical apparatus and
wiring.
– High Pressure. Keep clear of nozzle.
– If connection is made to a potable water
system, the system shall be protected
against backflow.
6 EN
Owner/User Responsibility
– The owner and/or user must have an
understanding of the manufacturer’s
operating instructions and warnings be-
fore using this pressure washer.
– Warning information should be empha-
sized and understood.
– If the operator is not fluent in English,
the manufacturer’s instructions and
warnings shall be read to and dis-
cussed with the operator in the opera-
tor’s native language by the purchaser/
owner, making sure that the operator
comprehends its contents.
– Owner and/or user must study and
maintain for future reference the manu-
facturers’ instructions.
GROUNDING INSTRUCTIONS
This product must be grounded. If it should
malfunction or breakdown, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock.
This product is equipped with a cord having
an equipment-grounding conductor and a
grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
DANGER
Improper connection of the equipmentgrounding conductor can result in a risk of
electrocution. Check with a qualified electrician or service personnel if you are in doubt
as to whether the outlet is properly grounded. Do not modify the plug provided with
the product - if it will not fit the outlet, have
a proper outlet installed by a qualified electrician. Do not use any type of adapter with
this product.
GROUND FAULT CIRCUIT IN-
TERRUPTER PROTECTION
This product is supplied with a Ground
Fault Circuit Interrupter (GFCI) built into the
power cord plug. This device provides additional protection from the risk of electric
shock. If power is interrupted in the line, the
GFCI will automatically re-close the circuit
to the load after power is restored. Depending on the GFCI model, it may be necessary to manually operate the reset button to
restore power to the GFCI load circuit. If replacement of the plug or cord is needed use
identical replacement parts.
WATER SUPPLY
몇 CAUTION
When connecting the water inlet to the water supply mains, local regulations of your
water company must be observed. In some
areas the unit must not be connected directly to the public drinking water supply.
This is to ensure that there is no feedback
of chemicals into the water supply. Direct
connection via a receiver tank or backflow
preventer, for example, is permitted.
Dirt in the feed water will damage the unit.
To avoid this risk, we recommend fitting a
water filter.
– Garden hose must be at least 3/4 inch
in diameter.
– Flow rate of water supply must not fall
below 5 GPM (gallons per minute).
– Flow rate can be determined by running
the water for one minute into an empty
5-gallon container.
– The water supply temperature must not
exceed 86°F/30°C.
– Never use the pressure washer to draw
in water contaminated with solvents,
e.g. paint thinners, gasoline, oil, etc.
– Always prevent debris from being
drawn into the unit by using a clean water source. Use additional water filter.
SAVE THESE INSTRUCTIONS!
7EN
Please read and comply with
these original instructions prior
to the initial operation of your appliance and
store them for later use or subsequent owners.
– Before first start-up it is definitely nec-
essary to read the operating instructions and safety indications Nr. 5.951-
949.0!
– In case of transport damage inform ven-
dor immediately
– Check the contents of the pack before
unpacking. For scope of delivery see illustration 1.
Contents
Environmental protection . . EN . . .1
Symbols in the operating in-
structions . . . . . . . . . . . . . . EN . . .1
Overview . . . . . . . . . . . . . . EN . . .2
Symbols on the machine . . EN . . .2
Proper use . . . . . . . . . . . . . EN . . .2
Safety instructions . . . . . . . EN . . .3
Safety Devices . . . . . . . . . . EN . . .3
Start up. . . . . . . . . . . . . . . . EN . . .3
GFCI INSTRUCTIONS. . . . EN . . .5
Operation . . . . . . . . . . . . . . EN . . .5
Storage. . . . . . . . . . . . . . . . EN . . .8
Transport . . . . . . . . . . . . . . EN . . .8
Maintenance and care . . . . EN . . .9
Troubleshooting . . . . . . . . . EN . .10
Warranty. . . . . . . . . . . . . . . EN . .12
Accessories and Spare Parts EN . .12
Technical specifications . . . EN . .13
Recurring tests . . . . . . . . . . EN . .14
Old appliances contain valuable materials that can be recycled; these should be sent for
recycling. Batteries, oil, and
similar substances must not
enter the environment. Please
dispose of your old appliances
using appropriate collection
systems.
Please do not release engine oil, fuel oil,
diesel and petrol into the environment
Protect the ground and dispose of used
oil in an environmentally-clean manner.
Notes about the ingredients (REACH)
You will find current information about the
ingredients at:
www.kaercher.com/REACH
Symbols in the operating in-
structions
Danger
Immediate danger that can cause severe
injury or even death.
몇 Warning
Possible hazardous situation that could
lead to severe injury or even death.
Caution
Possible hazardous situation that could
lead to mild injury to persons or damage to
property.
Environmental protection
The packaging material can be
recycled. Please do not throw
the packaging material into
household waste; please send
it for recycling.
8 EN
– 1
Overview
Device elements
Figure 1
1 Cover
2 Support for spray lance
(both sides)
3 Fill opening for system care Advance
RM 110/RM 111
4 Steering roller with fixed position brake
5 Mounting location for transport
(both sides)
6 Wheel
7 Water supply set
8 High pressure hose
9 O-ring set (for replacement)
10 Hand spray gun
11 Spray lance
12 High-pressure nozzle (stainless steel)
13 Steam nozzle (brass)
14 Safety latch of the hand spray gun
15 Power supply
16 Connection for water supply with filter
17 High pressure connection
18 Step depression
19 Pouring vent for detergent 2
20 Pouring vent for detergent 1
21 Folding compartment
22 Pouring vent for fuel
23 Handle
24 Operating field
25 Closing flap for storage compartment
26 Storage compartment for accessories
27 Nameplate
28 Cover lock
29 Oil tank
30 Pressure/quantity regulation of the
pump unit
31 Oil drain screw
32 Backflow valve of the detergent infeed
33 Detergent suction hose 1 with filter
34 Detergent suction hose 2 with filter
35 Fuel filter
36 Service switch
37 Water shortage safe guard with sieve
38 Float tank
39 Fine filter (water)
Operating field
Figure 2
A Power switch
B Temperature controller
C Dosage valve for detergent
D Manometer
1 Indicator lamp pump
2 “Ready for use” indicator lamp
3 Fuel indicator lamp
4 Engine indicator lamp
5 Indicator lamp burner failure
6 Indicator lamp service
7 Indicator lamp system care
Colour coding
– The operating elements for the cleaning
process are yellow.
– The controls for the maintenance and
service are light gray.
Symbols on the machine
High-pressure jets can be dangerous if improperly used. The
jet may not be directed at persons, animals, live electrical equipment or
at the appliance itself.
Proper use
Cleaning of: Machines, Vehicles, Structures, Tools, Facades, Terraces, Gardening tools, etc.
Danger
Risk of injury! Follow the respective safety
regulations when operating at gas stations
or other dangerous areas.
Please do not let mineral oil contaminated waste water reach soil, water or the
sewage system. Perform engine cleaning
and bottom cleaning therefore only on
specified places with an oil trap.
– 2
9EN
Safety instructions
PROPOSITION 65
WARNING
The burner exhaust from this product
contains chemicals known to the State of
California to cause cancer, birth defects
or other reproductive harm.
– Please follow the national rules and
regulations for fuel spray jets of the respective country.
– Please follow the national rules and
regulations for accident prevention of
the respective country. Fuel spray jets
must be tested regularly and the results
of these tests must be documented in
writing.
– The heating appliance of the machine is
an ignition plant. All national laws and
regulations about heating systems must
also be followed.
– As per the applicable national guide-
lines, the first time this high-pressure
cleaner must be taken into operation by
a skilled person. KÄRCHER has already performed this initial start-up for
you and has documented it accordingly.
The documentation can be requested at
your KÄRCHER partner. Please have
the part and plant number of the appliance available when enquiring about
the documentation.
– We would like to point out that the appli-
ance must be repeatedly checked by a
skilled person as prescribed by the applicable national regulations. Please
contact your KÄRCHER partner.
Safety Devices
Safety devices serve for the protection of
the user and must not be put out of operation or bypassed with respect to their function.
Overflow valve with two pressure
switches
– While reducing the water supply at the
pump head or with the Servopress regulation the overflow valve opens and
part of the water flows back to the pump
suck side.
– If the hand-spray gun is closed, so that
the whole water flows back to the pump
suck side, the pressure switch at the
overflow valve shuts down the pump.
– If the hand spray gun is opened, the
pressure switch on the cylinder head
turns the pump back on.
The overflow valve is set by the manufacturer and sealed. Setting only by customer
service.
Safety valve
– The safety valve opens, when the over-
flow valve resp. the pressure switch is
broken.
The safety valve is set by the manufacturer
and sealed. Setting only by customer service.
Water shortage safeguard
– The water shortage safeguard prevents
the burner to be turned on when there is
water shortage.
– A sieve prevents the contamination of
the safeguard and must be cleaned regular.
Temperature stop for exhaust gases
– The temperature stop switches off the
machine when the waste gases have
reached very high temperatures.
Start up
몇 Warning
Risk of injury! Device, tubes, high pressure
hose and connections must be in faultless
condition. Otherwise, the appliance must
not be used.
Lock parking brake.
10 EN
– 3
Installing the handle
Figure 3
Caution
Hook the electric supply line into the cable
guide of the right handle bow. Ensure that
the cable is not damaged.
Refill system care
Note: To protect the device, the burner is
switched off 5 hours after the system care
container is empty.
– The system care prevents the calcifica-
tion of the heating spiral while operating
with calciferous tap water. It is dosed
into the supply in the float container
drop by drop.
– The metering is set to medium water ri-
gidity by the manufacturer
Note: A sample bundle of system care is included.
Refill system care.
Adjusting the dosage of the system
care Advance RM 110/RM 111
Determining the hardness of tap water:
– through the public water supply works,
– using a hardness tester (order no.
6.768-004)
Water hardness (°dH)
<3 OFF (no dosing)
3...7 1
7...14 2
14...21 3
>21 4
Set the service switch according to the
water hardness in the table.
Note: Observe the following when using
system care Advance 2 RM 111:
– Calcification protection: See table
– Pump care and black water protection:
Set the service switch to at least setting
3.
Scale on the service
switch
Refill fuel
Danger
Risk of explosion! Only refill diesel oil or
light fuel oil. Unsuitable fuels, e.g. petrol,
are not to be used.
Caution
Never operate device with empty fuel tank
The fuel pump will otherwise be destroyed.
Refill fuel.
Close tank lock.
Wipe off spilled fuel.
Refill detergent
Caution
Risk of injury!
– Use Kärcher products only.
– Under no circumstances fill solvents
(petrol, aceton, diluting agent etc.)
– Avoid eye and skin contact.
– Observe safety and handling instruc-
tions by the detergent manufacturer.
Kärcher offers an individual cleaning
and care appliances program.
Your dealer will consult you gladly.
Refill detergent.
Install the hand-spray gun, the jet
pipe, the nozzle and the high pres-
sure hose
Figure 4
Connect ray tube with hand spray gun
Tighten the screw connection of the
spray lance finger tight.
Insert high pressure nozzle into cover-
ing nut
Install covering nut and tighten firmly
Connect the high pressure hose to the
hand-spray gun.
Connect the high pressure hose to the
high pressure connection point of the
machine.
Installing spare high pressure hose
Figure 5
– 4
11EN
Water connection
For connection values refer to technical
specifications
Attach supply hose (minimum length
24.6 ft/7.5 m, minimum diameter 3/4“)
to the water supply set by means of a
hose clamp.
Connect the supply hose to the water
connection point of the machine and at
the water supply point (for e.g. a tap).
Note: The supply hose and the hose clamp
are not included in the scope of delivery.
Suck in water from vessel
If you want to suck in water from an external vessel, the following modification is
necessary:
Figure 6
Open fill opening for system care.
Release and remove the cover of the
system care.
Remove water connection from the fine
filter.
Unscrew the fine filter from the pump
head.
Figure 7
Remove the system care reservoir.
Unscrew the top supply hose to the
swimmer container.
Figure 8
Connect the top supply hose at pump
head.
Replug the rinse line of the detergent
dosing valve.
Connect suction hose (minimum diame-
ter 3/4“) with filter (accessory) to the
water connection point.
– Max. suck height: 1.6 ft (0.5 m)
Until the pump sucked in water, you should:
Set the pressure/quantity regulation at
the pump unit to maximum quantity.
Close the dosing valve for the deter-
gent.
Danger
Never suck in water from a drinking water
container. Never suck in liquids which contain solvents like lacquer thinner, petrol, oil
or unfiltered water. The sealings within the
device are not solvent resistant. The spray
mist of solvents is highly inflammable, explosive and poisonous.
Note: Assembly in reverse order. Ensure
that the solenoid valve cable on the reservoir of the system care is not pinched.
Power connection
– For connection values, see technical
data and type plate.
– The electrical connections must be
done by an electrician according to
NEC and local codes.
GFCI INSTRUCTIONS
STEP 1: Plug the Ground Fault Circuit
Interrupter (GFCI) into a working outlet.
STEP 2: Press ’’TEST’’, then press
’’RESET’’ to assure proper connection
to power.
Note: The actual appearance of the
GFCI may be different from this illustration.
Operation
Danger
Risk of explosion!
Do not spray flammable liquids.
Caution
Never operate device with empty fuel tank
The fuel pump will otherwise be destroyed.
12 EN
– 5
Safety instructions
몇 Warning
Long hours of using the appliance can
cause circulation problems in the hands on
account of vibrations.
It is not possible to specify a generally valid
operation time, since this depends on several factors:
– Proneness to blood circulation deficien-
cies (cold, numb fingers).
– Low ambient temperature. Wear warm
gloves to protect hands.
– A firm grip impedes blood circulation.
– Continuous operation is worse than an
operation interrupted by pauses.
In case of regular, long-term operation of
the device and in case of repeated occurrence of the symptoms (e.g. cold, numb fingers) please consult a physician.
Replace the nozzle
Danger
Switch the appliance off prior to replacing
nozzle and activate hand spray gun until
device is pressureless.
Operating modes
Turning on the Appliance
Set appliance switch to desired operat-
ing mode.
Indicator lamp for operational readiness
lights up.
The device starts briefly and turns off, as
soon as the working pressure is reached.
Note: If the indicator lamps for pump, burner malfunction or engine are on during operation, turn off the appliance immediately
and repair malfunction, refer to "Help with
malfunctions".
Release the trigger gun.
When activating the hand spray gun the device switches back on.
Note: If no water comes out of the high
pressure nozzle, vent pump. Refer to "Help
with malfunctions - appliance is not building
up pressure".
Adjust cleaning temperature
Set temperature regulator to desired
temperature.
86 °F/30 °C to 208 °F/98 °C:
– Clean with hot water.
212 °F/100 °C to 302 °F/150 °C
– Clean using steam.
Replace the high-pressure nozzle
(stainless steel) with steam nozzle
(brass), (refer to "Using steam").
Set working pressure and flow rate
0/OFF =Off
1 Operating with cold water
2 Eco operation (hot water max. 140 °F/
60 °C)
3 Operating with hot water/steam
Pressure/quantity regulation of the
pump unit
Turn the regulation spindle in a clock-
wise direction: Increase working pressure (MAX).
Turn the regulation spindle in an anti-
clockwise direction: Reduce working
pressure (MIN).
– 6
13EN
Operation with detergent
– For considerate treatment of the envi-
ronment use detergent economically.
– The detergent must be suitable for the
surface to be cleaned.
With support of the detergent dose
valve set detergent concentration as
determined by the manufacturer.
Note: Recommended values at the control
panel at maximum working pressure.
Cleaning
Set pressure/temperature and deter-
gent concentration according to the surface to be cleaned.
Note: To prevent damage due to too much
pressure, always position high pressure ray
first from a greater distance towards object
to be cleaned.
Recommended cleaning method
– Loosen the dirt:
Spray detergent economically and let it
work for 1...5 minutes but do not let it
dry up.
– Remove the dirt:
Spray off loosened dirt with the high
pressure jet.
Operating with cold water
Removal of light contaminations and clear
rinse, i.e.: Gardening tools, terrace, tools,
etc.
Set operating pressure according to
need.
Eco operation
The appliance works in the most economical temperature range.
Note: The temperature can be regulated
up to 140 °F/60 °C.
Operating with hot water/steam
We recommend the following cleaning temperatures:
– Light contaminations
86 °F/30 °C-122 °F/50 °C
– Contaminations containing protein, i.e.
in the food processing industry
max. 140 °F/60 °C
– Vehicle cleaning, machine cleaning
140 °F/60 °C-194 °F/90 °C
– De-preserve, contaminations contain-
ing strong fat contents
212 °F/100 °C-230 °F/110 °C
– De-frosting of surcharge substances,
partially facade cleaning
up to 284 °F/140 °C
Operating with hot water
Danger
Scalding danger!
Set temperature regulator to desired
temperature.
Operating with steam
Danger
Scalding danger!
Therefore the following measures must
definitely be performed:
Replace high pressure nozzle (stain-
less steel) with steam nozzle (brass,
order see specification).
Set the operating pressure on the pump
unit to the minimum value.
Set temperature regulator to min.
212 °F/100 °C.
After operation with detergent
Set dosing value for detergent to "0".
Set the appliance switch to "1" (opera-
tion with cold water).
Open the hand spray gun and rinse the
appliance for at least 1 minute.
14 EN
– 7
Turn off the appliance
Danger
Danger of scalding by hot water. After the
operation with hot water or steam, the device must be operated with opened gun
with cold water for at least two minutes.
Set the appliance switch to "0/OFF“.
Shut off water supply.
Turn on pump shortly (appr. 5 seconds)
with device switch.
Pull main plug out of socket with dry
hands only.
Remove water connection.
Activate hand spray gun until device is
pressure less.
Lock the trigger gun.
Storing the Appliance
Lock in the steel pipe into the holder of
the appliance hood.
Roll up high pressure hose and electri-
cal conduit and hang them into the respective holders.
Note: Do not twist high pressure hose and
electrical conduit.
Frost protection
Caution
Frost will destroy the not completely water
drained device.
Store in a frost free area.
If the device is connected to a chimney, the
following must be observed:
Caution
Threat of damage by penetrating cold air
through the chimney.
Disconnect device from chimney when
outside temperature drops below 32 °F/
0 °C.
If it is not possible to store frost free, shut
down device.
Shutdown
For longer work breaks or if a frost free storage is not possible:
Drain water.
Flush device with anti-freeze agent.
Empty detergent tank.
Dump water
Screw off water supply hose and high
pressure hose.
Screw off supply hose at boiler bottom
and drain heating spiral empty.
Operate device for max. 1 minute until
the pump and conduits are empty.
Flush device with anti-freeze agent
Note: Observe handling instructions of the
anti-freeze agent manufacturer.
Fill anti-freeze agent of the trade into
swimmer container.
Switch on appliance (without heater) till
the appliance has been completely
rinsed.
A certain corrosion protection is achieved
with this as well.
Storage
Caution
Risk of injury and damage! Note the weight
of the appliance in case of storage.
Transport
Figure 9
Caution
Risk of damage! When loading the appliance with a forklift, observe the illustration.
Caution
Risk of injury and damage! Observe the
weight of the appliance when you transport
it.
When transporting in vehicles, secure
the appliance according to the guidelines from slipping and tipping over.
– 8
15EN
Maintenance and care
Maintenance Works
Danger
Risk of injury by inadvertent startup of appliance and electrical shock.
First pull out the plug from the mains before
carrying out any tasks on the machine.
Set the appliance switch to "0/OFF“.
Shut off water supply.
Turn on pump shortly (appr. 5 seconds)
with device switch.
Pull main plug out of socket with dry
hands only.
Remove water connection.
Activate hand spray gun until device is
pressure less.
Lock the trigger gun.
Allow device to cool down.
Your Kärcher vender will inform you
about the performance of a periodic
safety inspection resp. signing of a
maintenance contract.
Maintenance intervals
Weekly
Clean the sieve in the water connection.
Clean the fine filter.
Check oil level.
Caution
In case of lacteous oil inform Kärcher customer service immediately
Monthly
Clean sieve in the water shortage safe
guard.
Clean filter at the detergent suck hose.
After 500 operating hours, at least annually
Oil change.
At least every 5 years, recurring
Perform the pressure test as per manu-
facturer's instructions.
Clean the sieve in the water connection
Take out sieve.
Clean sieve in water and reinstall.
Cleaning the fine filter
Unpressurize the appliance.
Unscrew the fine filter from the pump
head.
Remove the fine filter and the filter in-
sert.
Clean the filter with clean water or com-
pressed air.
Reinstall in reverse sequence.
Clean sieve in the water shortage safe
guard
Loosen covering nut and take off hose.
Take out sieve.
Note: If necessary turn in screw M8 appr.
0.2 in/5 mm inwards and therewith pull out
sieve.
Clean sieve in water.
Push sieve inwards.
Put on hose.
Tighten covering nut firmly.
Clean filter at the detergent suck hose
Take out detergent suck supports.
Clean filter in water and reinstall.
Oil change
Ready a catch bin for appr. 0.26 gal/
1 Liter oil.
Loosen release screw.
Dispose of old oil ecologically or turn in at
a gathering point.
Tighten release screw.
Fill oil slowly up to the MAX marking.
Note: Air pockets must be able to leak out.
For oil type refer to technical specifications.
16 EN
– 9
Troubleshooting
Danger
Risk of injury by inadvertent startup of appliance and electrical shock.
First pull out the plug from the mains before
carrying out any tasks on the machine.
Indicator lamp pump
1x blinking
– Lack of oil
Replenish oil.
2x blinking
– Leak in the high pressure system
Check high pressure system and con-
nections for tightness.
3x blinking
– Water shortage
Check water supply, check connec-
tions.
4x blinking
– Obstructed reed switch in the water
shortage safe guard.
Check water shortage safe guard.
Indicator lamp "Ready for use"
turns off
– No line voltage, see "Appliance is not
running".
Engine indicator lamp
1x blinking
– Contactor error
Set the appliance switch to "0/OFF“.
Turn on the appliance.
– Error occurs repeatedly.
Inform Customer Service
2x blinking
– Engine overload/overheat
Set the appliance switch to "0/OFF“.
Allow device to cool down.
Turn on the appliance.
– Error occurs repeatedly.
Inform Customer Service
3x blinking
– Fault in the voltage supply.
Check main connections and mains
fuse.
4x blinking
– Excessive power consumption.
Check main connections and mains
fuse.
Inform Customer Service
Indicator lamp burner failure
1x blinking
– The exhaust temperature limiter has
been triggered.
Set the appliance switch to "0/OFF“.
Allow device to cool down.
Turn on the appliance.
– Error occurs repeatedly.
Inform Customer Service
2x blinking (option)
– The flame sensor turned the burner off.
Inform Customer Service
3x blinking
– System care detection defective
Inform Customer Service
4x blinking
– Temperature sensor defective
Inform Customer Service
Indicator lamp service
– Service interval
Perform service work.
Fuel indicator lamp glows
– Fuel tank empty.
Refill fuel.
Indicator lamp system care is illumi-
nated
Note: Burner can operate 5 more hours.
– System care tank is empty, due to tech-
nical reasons a remainder stays in the
tank.
Refill system care.
– 10
17EN
Indicator lamp system care is blink-
ing
Note: Burner operation no longer possible.
– System care container is empty.
Refill system care.
Appliance is not running
– No power
Check power connection/conduit.
Device is not building up pressure
– Air within the system
Vent pump:
Set dosing value for detergent to "0".
With open hand spray gun turn device
on and off multiple times with the device
switch.
Open and close the pressure/quantity
regulation at the pump unit with the
hand spray gun open.
Note: By dismantling the high pressure
hose from the high pressure connection the
venting process is accelerated.
If detergent tank is empty, refill.
Check connections and conduits.
– Pressure is set to MIN
Set pressure to MAX.
– Sieve in the water connection is dirty
Clean sieve.
Clean the fine filter; replace it, if neces-
sary.
– Amount of water supply is too low.
Check water supply level (refer to tech-
nical data).
Device leaks, water drips from the
bottom of the device
– Pump leaky
Note: 3 drops/minute are allowed.
With stronger leak, have device
checked by customer service.
Device turns on and off while hand
spray gun is closed
– Leak in the high pressure system
Check high pressure system and con-
nections for tightness.
Device is not sucking in detergent
Leave device running with open deter-
gent dosage valve and closed water
supply, until the swimmer tank is
sucked empty and the pressure falls to
"0".
Open the water supply again.
If the pump still is not sucking in any deter-
gent, it could be because of the following
reasons:
– Filter in the detergent suck hose dirty
Clean filter.
– Backflow valve stuck
Remove the detergent hose and loosen
the backflow valve using a blunt object.
Burner does not start
– System care container is empty.
Refill system care.
– Fuel tank empty.
Refill fuel.
– Water shortage
Check water supply, check connec-
tions.
Clean sieve in the water shortage safe
guard.
– Fuel filter dirty
Change fuel filter.
– No ignition spark
If device is in use and no ignition spark
can be seen through the viewing glass,
have device checked by customer ser-
vice.
18 EN
– 11
Loading...