Power Output20 W RMS × 4 Channels at 4 Ω and [< or =] 1% THD+N
Signal to Noise Ratio80 dBA (reference: 1 W into 4 Ω)
Load Impedance4 Ω (4 Ω to 8 Ω allowance)
Equalizer Control Range Frequencies60 Hz, 150 Hz, 400 Hz, 1 kHz, 2.4 kHz, 6 kHz, 15 kHz
Color systemNTSC
Video Output (composite)1 Vp-p/75 Ω
Other TerminalsLINE IN, CD changer, 2nd AUDIO OUT
Frequency RangeFM87.5 MHz to 107.9 MHz (with channel interval set to 100 kHz or 200 kHz)
AM530 kHz to 1 710 kHz (with channel interval set to 10 kHz)
FM TunerUsable Sensitivity11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz) 65 dB
Frequency Response40 Hz to 15 000 Hz
Stereo Separation35 dB
AM TunerSensitivity/Selectivity20 µV/35 dB
Signal Detection SystemNon-contact optical pickup (semiconductor laser)
Number of Channels2 channels (stereo)
Frequency ResponseDVD, fs=48 kHz16 Hz to 22 000 Hz
DVD, fs=96 kHz16 Hz to 22 000 Hz
CD, fs=44.1 kHz16 Hz to 20 000 Hz
Dynamic Range96 dB
Signal-to-Noise Ratio98 dB
Wow and FlutterLess than measurable limit
DivXVideo : Max. Resolution720 × 480 pixels (30 fps)
Power RequirementOperating VoltageDC 14.4 V (11 V to 16 V allowance)
Grounding SystemNegative ground
Allowable Operating Temperature0°C to +40°C (32°F to 104°F)
Dimensions (W × H × D) Installation Size (approx.)182 mm × 52 mm × 158 mm (7-3/16" × 2-1/16" × 6-1/4")
Panel Size (approx.)188 mm × 58 mm × 11 mm (7-7/16" × 2-5/16" × 7/16")
Mass (approx.)1.7 kg (3.3 lbs) (excluding accessories)
AUDIO AMPLIFIER SECTION
Output level : -21 dBm to -15 dBm
KD-DV6200 : 2.5 V/20 kΩ load (full scale)
KD-DV6200 : 2.0 V/20 kΩ load (full scale)
TUNER SECTION
87.5 MHz to 108.0 MHz (with channel interval set to 50 kHz)
531 kHz to 1 602 kHz (with channel interval set to 9 kHz)
Maximum Power OutputFront/Rear50 W per channel
Continuous Power Output (RMS) Front/Rear19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion
Load Impedance4 Ω (4 Ω to 8 Ω allowance)
Equalizer Control RangeFrequencies60 Hz, 150 Hz, 400 Hz, 1 kHz, 2.4 kHz, 6 kHz, 15 kHz
Level±10 dB
Signal to Noise Ratio70 dB
Audio Output LevelDigital (DIGITAL OUT: Optical)Signal wave length : 660 nm
Output Impedance1 kΩ
Subwoofer-out Level/Impedance2.0 V/20 kΩ load (full scale)
Color systemPAL
Video Output (composite)1 Vp-p/75 Ω
Other TerminalsLINE IN, CD changer, 2nd AUDIO OUT
Frequency RangeFM87.5 MHz to 108.0 MHz
AM(MW) 522 kHz to 1 620 kHz
FM TunerUsable Sensitivity11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz) 65 dB
Frequency Response40 Hz to 15 000 Hz
Stereo Separation30 dB
MW TunerSensitivity/Selectivity20 µV/35 dB
LW TunerSensitivity50 µV
Signal Detection SystemNon-contact optical pickup (semiconductor laser)
Number of Channels2 channels (stereo)
Frequency ResponseDVD, fs=48 kHz16 Hz to 22 000 Hz
DVD, fs=96 kHz16 Hz to 22 000 Hz
CD, fs=44.1 kHz16 Hz to 20 000 Hz
Dynamic Range96 dB
Signal-to-Noise Ratio98 dB
Wow and FlutterLess than measurable limit
DivXVideo : Max. Resolution720 × 480 pixels (30 fps)
Power RequirementOperating VoltageDC 14.4 V (11 V to 16 V allowance)
Grounding SystemNegative ground
Allowable Operating Temperature0°C to +40°C
Dimensions (W × H × D)Installation Size (approx.)182 mm × 52 mm × 158 mm
Panel Size (approx.)188 mm × 58 mm × 11 mm
Mass (approx.)1.7 kg (excluding accessories)
Maximum Power OutputFront/Rear50 W per channel
Continuous Power Output (RMS) Front/Rear19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion
Load Impedance4 Ω (4 Ω to 8 Ω allowance)
Equalizer Control RangeFrequencies60 Hz, 150 Hz, 400 Hz, 1 kHz, 2.4 kHz, 6 kHz, 15 kHz
Level±10 dB
Signal to Noise Ratio70 dB
Audio Output LevelDigital (DIGITAL OUT: Optical)Signal wave length : 660 nm
Output Impedance1 kΩ
Subwoofer-out Level/Impedance2.0 V/20 kΩ load (full scale)
Color systemPAL/NTSC
Video Output (composite)1 Vp-p/75 Ω
Other TerminalsLINE IN, CD changer, 2nd AUDIO OUT
Frequency RangeFM87.5 MHz to 108.0 MHz
AM531 kHz to 1 602 kHz
FM TunerUsable Sensitivity11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz) 65 dB
Frequency Response40 Hz to 15 000 Hz
Stereo Separation30 dB
AM TunerSensitivity/Selectivity20 µV/35 dB
Signal Detection SystemNon-contact optical pickup (semiconductor laser)
Number of Channels2 channels (stereo)
Frequency ResponseDVD, fs=48 kHz16 Hz to 22 000 Hz
DVD, fs=96 kHz16 Hz to 22 000 Hz
CD, fs=44.1 kHz16 Hz to 20 000 Hz
Dynamic Range96 dB
Signal-to-Noise Ratio98 dB
Wow and FlutterLess than measurable limit
DivXVideo : Max. Resolution720 × 480 pixels (30 fps)
Power RequirementOperating VoltageDC 14.4 V (11 V to 16 V allowance)
Grounding SystemNegative ground
Allowable Operating Temperature0°C to +40°C
Dimensions (W × H × D)Installation Size (approx.)182 mm × 52 mm × 158 mm
Panel Size (approx.)188 mm × 58 mm × 11 mm
Mass (approx.)1.7 kg (excluding accessories)
Maximum Power OutputFront/Rear50 W per channel
Continuous Power Output (RMS) Front/Rear19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion
Load Impedance4 Ω (4 Ω to 8 Ω allowance)
Equalizer Control RangeFrequencies60 Hz, 150 Hz, 400 Hz, 1 kHz, 2.4 kHz, 6 kHz, 15 kHz
Level±10 dB
Signal to Noise Ratio70 dB
Audio Output LevelDigital (DIGITAL OUT: Optical)Signal wave length : 660 nm
Output Impedance1 kΩ
Subwoofer-out Level/Impedance2.0 V/20 kΩ load (full scale)
Color systemPAL
Video Output (composite)1 Vp-p/75 Ω
Other TerminalsLINE IN, CD changer, 2nd AUDIO OUT
Frequency RangeFM1 /FM287.5 MHz to 108.0 MHz
FM365.00 MHz to 74.00 MHz
AM(MW) 522 kHz to 1 620 kHz
FM TunerUsable Sensitivity11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz) 65 dB
Frequency Response40 Hz to 15 000 Hz
Stereo Separation30 dB
MW TunerSensitivity/Selectivity20 µV/35 dB
LW TunerSensitivity50 µV
Signal Detection SystemNon-contact optical pickup (semiconductor laser)
Number of Channels2 channels (stereo)
Frequency ResponseDVD, fs=48 kHz16 Hz to 22 000 Hz
DVD, fs=96 kHz16 Hz to 22 000 Hz
CD, fs=44.1 kHz16 Hz to 20 000 Hz
Dynamic Range96 dB
Signal-to-Noise Ratio98 dB
Wow and FlutterLess than measurable limit
DivXVideo : Max. Resolution720 × 480 pixels (30 fps)
Power RequirementOperating VoltageDC 14.4 V (11 V to 16 V allowance)
Grounding SystemNegative ground
Allowable Operating Temperature0°C to +40°C
Dimensions (W × H × D)Installation Size (approx.)182 mm × 52 mm × 158 mm
Panel Size (approx.)188 mm × 58 mm × 11 mm
Mass (approx.)1.7 kg (excluding accessories)
Design and specifications are subject to change without notice.
(No.MA250)1-5
1.1Safety Precautions
SECTION 1
PRECAUTIONS
!
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
Please use enough caution not to see the beam directly or touch it in case of an
adjustment or operation check.
1-6 (No.MA250)
1.2Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.2.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron plate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.3Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.4Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the pickup unit.
• Apply solder to the short land before the flexible wire is disconnected from the connector on the pickup unit.
(If the flexible wire is disconnected without applying solder, the pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land after connecting the flexible wire.
Flexible wire
CN101
Short-circuit points
Mechanism control board
(No.MA250)1-7
1.5Important for laser products
!
1.CLASS 1 LASER PRODUCT
2.DANGER : Invisible laser radiation when open and inter
lock failed or defeated. Avoid direct exposure to beam.
3.CAUTION : There are no serviceable parts inside the
Laser Unit. Do not disassemble the Laser Unit. Replace
the complete Laser Unit if it malfunctions.
4.CAUTION : The CD,MD and DVD player uses invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
REPRODUCTION AND POSITION OF LABELS
WARNING LABEL
CAUTION : Visible and Invisible
CLASS 1
LASER PRODUCT
laser radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE TO
BEAM. (e)
ADVARSEL : Synlig og usynlig
laserstråling når maskinen er
åben eller interlocken fejeler.
Undgå direkte eksponering til
stråling. (d)
VARNING : Synlig och
osynling laserstrålning när
den öppnas och spärren är
urkopplad. Betrakta ej
strålen. (s)
VARO : Avattaessa ja suojalukitus
ohitettuna tai viallisena olet alttiina
näkyvälle ja näkymättömälle
lasersäteilylle. Vältä säteen
kohdistumista suoraan itseesi. (f)
1-8 (No.MA250)
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
(No.MA250)1-9
SECTION 3
DISASSEMBLY
3.1Main body section
3.1.1 Removing the front panel assembly
(See Fig.1)
(1) Push the control panel release button in the lower left part
of the front panel assembly and remove the front panel assembly.
(2) Take out the front panel assembly.
3.1.2 Removing the bottom cover
(See Fig.2)
(1) Turn the main body up side down.
(2) Insert a screwdriver under the joints to release the joints a
on the left side, joints b on the right side and joint c on the
back side of the main body, then remove the bottom cover
from the main body.
Caution:
When releasing the joints using a screwdriver, do not damage
the main board.
When remove the bottom cover, do not missing the cooling
rubber.
Front panel assembly
Control panel release button
Fig.1
Bottom cover
b
a
b
a
c
Fig.2
1-10 (No.MA250)
Loading...
+ 22 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.