AT-3203-J 1/2-INCH
POWER RATCHET
WRENCH
CAUTION
RISK OF INJURY!
READ MANUAL BEFORE OPERATING!
THIS MANUAL IS AN IMPORTANT PART OF THE RATCHET WRENCH AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT.
1/2-Inch Power Ratchet Wrench Operator's Manual |
1 |
Introduction
Congratulations on the purchase of your new John Deere 1/2-Inch Power Ratchet Wrench! You can be assured your power ratchet wrench was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance.
The John Deere 1/2-Inch Power Ratchet Wrench is designed for a wide variety of fastening applications. This unit features a lever type throttle for convenient operation, front exhaust directs air away from operator and a ball type socket retainer for quick and easy socket removal. Increased length allows higher torque applications with less effort.
This operator's manual was compiled for your benefit. By reading and following the simple safety, installation, operation, maintenance and troubleshooting steps described in this manual, you will receive years of trouble-free operation from your new power ratchet wrench. The contents of this manual are based on the latest product information available at the time of publication. The manufacturer reserves the right to make changes in price, color, materials, equipment, specifications or models at any time without notice.
Once the unit has been removed from the box, immediately write in the serial number of your unit in the space provided below.
SERIAL NUMBER_________________________________
Inspect for signs of obvious or concealed freight damage. If damage does exist, file a claim with the transportation company immediately. Be sure that all damaged parts are replaced and that the mechanical problems are corrected prior to operation of the unit. If you require service, contact your Customer Service.
Mi-T-M® Corporation, 8650 Enterprise Drive, Peosta, IA 52068 1-877-JD-KLEEN / (1-877-535-5336) Fax 563-556-1235
Monday - Friday 8:00 a.m. - 5:00 p.m. CST
Please have the following information available for all service calls:
1.Model Number
2.Serial Number
3.Date and Place of Purchase
2 |
1/2-Inch Power Ratchet Wrench Operator's Manual |
Table of Content
INTRODUCTION .................................................................................................... |
2 |
TABLE OF CONTENTS ......................................................................................... |
3 |
SAFETY .................................................................................................................. |
4-6 |
RECOGNIZE SAFETY INFORMATION ................................................ |
4 |
UNDERSTAND SIGNAL WORDS ......................................................... |
4 |
READ OPERATING INSTRUCTIONS ................................................... |
4 |
ALWAYS WEAR APPROVED EYE PROTECTION ............................. |
5 |
HEARING PROTECTION IS RECOMMENDED ................................... |
5 |
WEAR RESPIRATORY PROTECTION ................................................ |
5 |
AVOID PROLONGED EXPOSURE TO VIBRATION ............................ |
6 |
90 PSIG MAXIMUM ............................................................................... |
6 |
USE ONLY POWER SOCKETS AND ACCESSORIES ........................ |
6 |
INSTALLATION ...................................................................................................... |
7 |
RECOMMENDED AIR LINE SET-UP .................................................... |
7 |
OPERATION ........................................................................................................... |
8 |
MAINTENANCE ..................................................................................................... |
8 |
TROUBLESHOOTING ........................................................................................... |
9 |
SPECIFICATIONS .................................................................................................. |
9 |
STATEMENT OF WARRANTY .............................................................................. |
10-11 |
FRENCH ................................................................................................................. |
12-21 |
SPANISH ................................................................................................................ |
22-31 |
1/2-Inch Power Ratchet Wrench Operator's Manual |
3 |
Safety
RECOGNIZE SAFETY INFORMATION
This is the safety alert symbol. When you see this symbol on your pneumatic tool or in this manual, be alert to the potential for personal injury.
Follow recommended precautions and safe operating practices.
UNDERSTAND SIGNAL WORDS
A "DANGER, WARNING or CAUTION" safety warning will be surrounded by a "SAFETY ALERT BOX." This box is used to designate and emphasize Safety Warnings that must be followed when operating this tool.
Accompanying the Safety Warnings are "signal words" which designate the degree or level of hazard seriousness. The "signal words" used in this manual are as follows:
DANGER: Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided MAY result in minor or moderate injury.
READ OPERATING INSTRUCTIONS
Always become familiar with all the instructions and warnings before operating any pneumatic tool.
ALWAYS PROVIDE A COPY OF THIS MANUAL TO ANYONE USING THIS EQUIPMENT. READ ALL INSTRUCTIONS BEFORE OPERATING THIS TOOL AND ESPECIALLY POINT OUT THE "SAFETY WARNINGS" TO PREVENT THE POSSIBILITY OF PERSONAL INJURY TO THE OPERATOR.
4 |
1/2-Inch Power Ratchet Wrench Operator's Manual |
WARNING
ALWAYS WEAR APPROVED EYE PROTECTION
Impact resistant eye protection should meet or exceed the standards as set forth in the United
States ANSI Z87.1, Occupational and Educational Eye and Face Protection. Look for the marking Z87.1 on your eye protection to insure that it is an approved style. For further information, ANSI Z87.1,
Occupational and Educational Eye and Face
Protection, is available from the American National Standards Institute, Inc., 11 West 42nd Street, New York, NY 10036.
HEARING PROTECTION IS RECOMMENDED
Hearing protection should be used when the noise level exposure equals or exceeds an 8 hour timeweighted average sound level of 85 dBA. Process noise, reflective surfaces, other tools being operated nearby, all add to the noise level present in your work area. If you are unable to determine your noise level exposure, we recommend the use of hearing protection.
WEAR RESPIRATORY PROTECTION
It is advisable, when using this tool for extended periods of time, to wear a protective mask. This will help prevent the inhalation of the fine dust produced while using this tool. Prolonged breathing of dust particles may lead to future respiratory problems.
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or reproductive harm. Some examples of these chemicals are:
•Lead from lead-base paints
•Crystalline Silica from bricks, cement and other masonry products.
•Arsenic and Chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well ventilated area and work with approved safety equipment such as those dust masks that are
specially designed to filter out microscopic particles.
1/2-Inch Power Ratchet Wrench Operator's Manual |
5 |
WARNING
AVOID PROLONGED EXPOSURE TO VIBRATION
Pneumatic tools can vibrate during use. Prolonged exposure to vibration or very repetitive hand and arm movements, can cause injury. Stop using any tool if discomfort, tingling feeling or pain occurs. You should consult your physician before resuming use of the tool.
CAUTION
90 PSIG MAXIMUM
Designed to operate at an air pressure of 90 pounds per square inch gauge pressure (90 PSIG) maximum, at the tool. Use of higher air pressure can, and may cause injury. Also use of higher air pressure places the internal components under loads and stresses they were not designed for, causing premature tool failure.
NOTE: The air supply should be clean and dry, preferably lubricated. For best results drain the moisture from your compressor daily.
USE ONLY POWER SOCKETS AND ACCESSORIES
Sockets and accessories used shall be of the power socket type. Always check sockets, retainers and drives regularly for wear or damage and replace when necessary.
6 |
1/2-Inch Power Ratchet Wrench Operator's Manual |
Installation
Designed to operate on 90 PSIG, lower pressure (below 90 PSIG) will reduce performance of the tool while higher air pressure (over 90 PSIG) raises the performance of the tool beyond its rated capacity and could cause serious damage to tool and user.
Always use clean dry air. Excessive moisture and dirt will greatly reduce the life of any air motor. We recommend the installation of an in-line filter-regulator-lubricator as close to the tool as possible.
A 3/8" air hose is required up to a length of 8 ft. If more length is required a 1/2" air hose should be connected to the 3/8" hose to ensure the tool has the necessary air supply. Be sure all hoses and fittings are the correct size and tightly secured.
RECOMMENDED AIR LINE SET-UP
1/2-Inch Power Ratchet Wrench Operator's Manual |
7 |
Operation
PRE-OPERATION:
Before the tool is connected to the air supply, clear the air hose of accumulated dust and moisture. Before removing a tool for service or changing sockets, make sure the air line is shut-off and drained of air. This will prevent the tool from operating if the throttle is accidently engaged.
OPERATION:
This wrench is equipped with a lever throttle which allows the operator to vary the speed. Direction control is located on the back of the ratchet head. Initial tightening and loosening of fasteners should be done manually with ratchet used as a hand tool. Nuts may then be run on and off with relative ease.
Keep sockets firmly against work surface when running tool to avoid jarring the sockets from the anvil or rounding the fastener heads. Excessive torque leverage above tool specifications will result in premature gear wear.
CAUTION: |
HAND TOOL SOCKETS CAN BREAK CREATING A |
|
HAZARD FROM FLYING PIECES. ALWAYS CHECK |
|
SOCKETS, RETAINERS AND DRIVES REGULARLY |
|
FOR WEAR OR DAMAGE AND REPLACE WHEN |
|
NECESSARY. |
THE DESIGN OF THIS TOOL REQUIRES THAT
EXTRA CARE MUST BE TAKEN WHEN USING THE
RATCHET IN TIGHT AREAS. HANDS AND FINGERS
SHOULD NOT BE HELD BETWEEN TOOL AND
WORK SURFACE. PERSONAL INJURY MAY
RESULT.
Maintenance
LUBRICATION:
An automatic in-line filter-regulator-lubricator is recommended as it increases tool life and keeps the tool in sustained operation. The in-line lubricator should be regularly checked and filled with John Deere AT-4003 air tool oil. Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to the exhaust ports and holding the throttle open approximately 30 seconds. The lubricator is properly set when
a light stain of oil collects on the paper. Excessive amounts of oil should be avoided.
In the event that it becomes necessary to store the tool for an extended period of time (overnight, weekend, etc.), it should receive a generous amount of lubrication at that time. The tool should be run for approximately 30 seconds to ensure oil has been evenly distributed throughout the tool. The tool should be stored in a clean and dry environment.
Recommended lubricants: Use John Deere AT-4003 air tool oil or any other high grade turbine oil containing moisture absorbent, rust inhibitors, metal wetting agents and an EP (extreme pressure) additive.
8 |
1/2-Inch Power Ratchet Wrench Operator's Manual |
Troubleshooting
Symptom |
Problem |
Solution |
||
|
|
|
||
Loss of Power |
1. Low air pressure |
1. Check air supply. For |
||
|
|
|
rated performance, 90 |
|
|
|
|
PSI air pressure is |
|
|
|
|
required at the tool, with |
|
|
|
|
tool operating |
|
|
2. |
Improper lubrication or dirt |
2. Check for wet or dirty |
|
|
|
build up |
air. Wet air tends to |
|
|
|
|
wash lubricant away. Dirt |
|
|
|
|
or foreign matter will |
|
|
|
|
impede the action of the |
|
|
|
|
motor. If dirt or water has |
|
|
|
|
entered the tool, flush |
|
|
|
|
with John Deere AT- |
|
|
|
|
4003. |
|
|
3. |
Worn motor parts, or other |
3. Contact your customer |
|
|
|
problems |
service. |
|
|
|
|
|
|
Specifications |
|
|
|
ITEM |
|
Drive size ---------------------------------------------- |
1/2" |
Free speed -------------------------------------------- |
175 RPM |
Maximum Torque ------------------------------------ |
75 ft.-lbs. |
Weight -------------------------------------------------- |
4 1/2 lbs. |
Overall length ---------------------------------------- |
14 1/2" |
Average Air consumption ------------------------- |
4 CFM |
Hose Size --------------------------------------------- |
3/8" |
Air inlet ------------------------------------------------- |
1/4" NPT |
Maximum operating pressure -------------------- |
90 PSI |
|
|
1/2-Inch Power Ratchet Wrench Operator's Manual |
9 |
Limited Warranty
John Deere Two-Year Limited Warranty. John Deere Wrench,
Models covered in this manual, are warranted by John Deere to the original user against defects in workmanship or materials under normal use for two years after date of purchase. Any part which is determined to be defective in material or workmanship and returned to an authorized service location, as John Deere designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced at John Deere’s option. For limited warranty claim procedures, see PROMPT DISPOSITION below. This limited warranty gives purchasers specific legal rights which may vary from jurisdiction to jurisdiction.
Limitation of Liability. To the extent allowable under applicable law, John Deere’s liability for consequential and incidental damages is expressly disclaimed. John Deere’s liability in all events is limited to and shall not exceed the purchase price paid.
Warranty Disclaimer. John Deere has made a diligent effort to provide product information and illustrate the products in this literature accurately; however, such information and illustrations are for the sole purpose of identification, and do not express or imply a warranty that the products are merchantable, or fit for a particular purpose, or that the products will necessarily conform to the illustrations or descriptions.
Except as provided below, no warranty or affirmation of fact, expressed or implied, other than as stated in the “LIMITED
WARRANTY” above is made or authorized by John Deere.
10 |
1/2-Inch Power Ratchet Wrench Operator's Manual |
Loading...