Jensen JHD1620 User Manual

JHD1620

AM/FM/RBDS/WB/AUX-IN/iPod Ready/SIRIUS Ready Heavy Duty Radio

Installation and Operation Manual

Guide d’inst allation et d’opération

CONTENTS

Introduction......................................................................................................... 1

Safety Information .............................................................................................. 2

Installation........................................................................................................... 3

Wiring................................................................................................................... 4

Basic Operation .................................................................................................. 5

Tuner Operation.................................................................................................. 8

Satellite Radio Operation................................................................................. 10

iPod Operation.................................................................................................. 12

Care and Maintenance................................................ .................................... .. 13

Troubleshooting................... .. ........................................................................... 13

Specifications ............................................... ... ................................................. 14

CONTENU

JHD1620

MOUNTING SCREW

REMOVAL TOOL

MOUNTING BUSHING

MOUNTING STRAP

DIN SLEEVE

FLANGE NUTS

HARDWARE KIT CONTENTS

INTRODUCTION

System Features

Features of the Jensen JHD1620 mobile audio system include:

• Full Dot Matrix LCD

• AM/FM US/EURO Tuner with 30 Presets (12 AM, 18 FM)

• RBDS (Radio Broadcast Data Service) with PTY Search

• SIRIUS Radio Ready with Song Seek

• iPod Ready (Cable Sold Separately)

• Weatherband Tuner with SAME Technology

•Mute

• Pre-set Equalizer - 5 settings (Flat, Rock, Pop, Classical, User)

• Electronic Bass, Treble, Balance and Fader Controls

• Output Power 45W x 4

• Clock 12/24 Hour Selectable

• Public Announcement (PA) Feature with Optional Microphone (sold separately)

• IR Wireless Remote Control Ready (sold separately)

• 2-Channel Pre-amp Line Level Outputs

• 2-Wire Power with Non-Volatile Memory and Clock/Time Support

• Auxiliary Audio Input (Front 3.5mm Stereo Jack, Rear RCA)

Content List

• Jensen Heavy Duty Radio

• Hardware Kit

• 15AMP Fuse

• Installation Manual

• Quick reference Guide

SAFETY INFORMATION

When Driving

Keep the volume level Iow enough to be aware of the road and traffic conditions.

When Washing Your Vehicle

Do not expose the product to water or excessive moisture. Moisture can cause electrical shorts, fire or other damage.

When Parked

Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior a chance to cool down before starting playback.

Use the Proper Power Supply

This product is designed to operate with a 12 volt DC negative ground battery system.

WARNING:

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.

JHD1620

182

Dashboard

Bend Tabs

Screw Stud

Dashboard

Plain Washer

Screw (5 x 25mm)

Hex Nut (5mm)

Screw Stud

Support Strap

Rubber Bushing

Removal Key

Sleeve

Removal Key

JHD1620

INSTALLATION

This unit is designed for installation in vehicle cabs with an existing 1-DIN radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. See the dealer where the radio was purchased for kit availability. Always check the kit application before purchasing to make sure the kit works with your vehicle.

Before You Begin

1. Disconnect Battery Before you begin, always disconnect the battery negative terminal.

2. Remove Transport Screws

Important Notes

• Before final installation, test the wiring connections to make sure the unit is connected properly and the system works.

• Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle.

• Install the unit where it does not interfere with driving and cannot injure passengers during a sudden or emergency stop.

• If the installation angle exceeds 30º from horizontal, the unit might not give optimum performance.

• Avoid installing the unit where it will be subject to high temperatures from direct sunlight, hot air, or from a heater, or subject to excessive dust, dirt or vibration.

DIN Front Mount

1. Slide the mounting sleeve off of the chassis if it has not already been removed. If it is locked into position, use the removal keys (supplied) to disengage it. The removal keys are depicted in “Removing the Unit” on page 3.

2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.

3. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard.

4. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve.

5. Follow the wiring diagram carefully and make certain all connections are secure and

6. After completing the wiring connections, turn the unit on to confirm operation (vehicle

insulated with crimp connectors or electrical tape to ensure proper operation.

accessory switch must be on). If the unit does not operate, recheck all wiring until the

problem is corrected. Once proper operation is achieved, turn the accessory switch off and proceed with final mounting of the chassis.

7. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place.

8. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and plain washer provided. Bend the strap, as necessary, to position it. Some vehicle installations provide cavity for rear support. In these applications, place the rubber bushing over the screw stud and insert the radio.

CAUTION: The perforated rear support strap or rear rubber mounting bushing must be used in the installation of the radio. Installation without either may result in damage to the radio or the mounting surface and void the manufacturer’s warranty.

9. Test radio operation by referring to the operating instructions for the unit.

Removing the Unit

To remove the radio after installation, remove the plastic end caps, insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit.

Reconnect Battery

When wiring is complete, reconnect the battery negative terminal.

WIRING

JHD1620

+ 12 hidden pages