HP OMNIBOOK 7100 User Manual

HP OmniBook 7100

Reference Guide

Notice

This manual and any examples contained herein are provided “as is” and are subject
to change without notice. Hewlett-Packard Company makes no warranty of any kind
with regard to this manual, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlett-Packard Co. shall not
be liable for any errors or for incidental or consequential damages in connection
with the furnishing, performance, or use of this manual or the examples herein.

Consumer transactions in Australia and the United Kingdom: The above disclaimers
and limitations shall not apply to Consumer transactions in Australia and the United
Kingdom and shall not affect the statutory rights of Consumers.

© Copyright Hewlett-Packard Company 1998. All rights reserved. Reproduction,
adaptation, or translation of this manual is prohibited without prior written
permission of Hewlett-Packard Company, except as allowed under the copyright
laws.

The programs that control this product are copyrighted and all rights are reserved.
Reproduction, adaptation, or translation of those programs without prior written
permission of Hewlett-Packard Co. is also prohibited.

This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Portions of the programs that control this product may also be copyrighted by
Microsoft Corporation, SystemSoft Corp., Crystal Semiconductor Corporation,
Phoenix Technologies, Ltd., and ATI Technologies Inc. See the individual programs
for additional copyright notices.

Microsoft, MS, MS-DOS, and Windows are registered trademarks of Microsoft
Corporation. Pentium and the Intel Inside logo are U.S. registered trademarks and
MMX is a U.S. trademark of Intel Corporation. TrackPoint is a U.S. registered
trademark of International Business Machines.

For warranty information, see the Support and Service booklet.

Hewlett-Packard Company
Mobile Computing Division
19310 Pruneridge Ave.
Cupertino, CA 95014

ii

HP Software Product License Agreement

Your HP OmniBook PC contains factory-installed software programs. Please read the
Software License Agreement before proceeding.

Carefully read this License Agreement before proceeding to operate this
equipment. Rights in the software are offered only on the condition that the
customer agrees to all terms and conditions of the License Agreement.
Proceeding to operate the equipment indicates your acceptance of these terms
and conditions. If you do not agree with the terms of the License Agreement,
you must now either remove the software from your hard disk drive and destroy
the master diskettes, or return the complete computer and software for a full
refund.

Proceeding with configuration signifies your acceptance of the License Terms.
Unless otherwise stated below, this HP Software Product License Agreement

shall govern the use of all software that is provided to you, the customer, as part
of the HP computer product. It shall supersede any non-HP software license
terms that may be found online, or in any documentation or other materials
contained in the computer product packaging.

Operating System Software by Microsoft is licensed to you under the Microsoft

Note:

End User License Agreement (EULA) contained in the Microsoft documentation.
The following License Terms govern the use of the software:

Use.

Customer may use the software on any one computer. Customer may not
network the software or otherwise use it on more than one computer. Customer may
not reverse assemble or decompile the software unless authorized by law.

Copies and Adaptations.

(a) for archival purposes or (b) when copying or adaptation is an essential step in
the use of the software with a computer so long as the copies and adaptations are
used in no other manner.

Ownership.

software, other than ownership of the physical media. Customer acknowledges and
agrees that the software is copyrighted and protected under the copyright laws.
Customer acknowledges and agrees that the software may have been developed by
a third party software supplier named in the copyright notices included with the
software, who shall be authorized to hold the Customer responsible for any
copyright infringement or violation of this Agreement.

Product Recovery CD-ROM.

CD-ROM: (i) The product recovery CD-ROM and/or support utility software may only
be used for restoring the hard disk of the HP computer with which the product
recovery CD-ROM was originally provided. (ii) The use of any operating system

Customer agrees that he/she does not have any title or ownership of the

Customer may make copies or adaptations of the software

If your computer was shipped with a product Recovery

iii

software by Microsoft contained in any such product recovery CD-ROM shall be
governed by the Microsoft End User License Agreement (EULA).

Transfer of Rights in Software.

third party only as part of the transfer of all rights and only if Customer obtains the
prior agreement of the third party to be bound by the terms of this License
Agreement. Upon such a transfer, Customer agrees that his/her rights in the software
are terminated and that he/she will either destroy his/her copies and adaptations or
deliver them to the third party.

Sublicensing and Distribution.

distribute copies or adaptations of the software to the public in physical media or by
telecommunication without the prior written consent of Hewlett-Packard.

Termination.

comply with any of these terms provided Hewlett-Packard has requested Customer
to cure the failure and Customer has failed to do so within thirty (30) days of such
notice.

Updates And Upgrades.

updates and upgrades which may be available from Hewlett-Packard under a
separate support agreement.

Export Clause.

or adaptation in violation of the U.S. Export Administration regulations or other
applicable regulation.

U.S. Government Restricted Rights.

Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the
Rights in Technical Data and Computer Software clause in DFARS 252.227-7013.
Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304 U.S.A. Rights
for non-DOD U.S. Government Departments and Agencies are as set forth in FAR

52.227-19(c)(1,2).

Hewlett-Packard may terminate this software license for failure to

Customer agrees not to export or re-export the software or any copy

Customer may transfer rights in the software to a

Customer may not lease, sublicense the software or

Customer agrees that the software does not include

Use, duplication, or disclosure by the U.S.

Edition History

Edition 1 (a).......................................... April 1998

This manual is printed on recycled paper.

iv

Contents

1. Introducing the OmniBook ............................... 1-1

Taking Inventory....................................... 1-3

Included in the OmniBook 7100 box ....................... 1-3

To buy OmniBook accessories ........................... 1-4

OmniBook features ................................... 1-5

Setting Up Windows .................................... 1-8

To set up the OmniBook ............................... 1-9

Configuring the OmniBook with the BIOS Setup Utility............. 1-10

To run the BIOS Setup utility............................. 1-10

Configuring the OmniBook with TopTools ..................... 1-16

To install TopTools ................................... 1-16

To run TopTools ..................................... 1-16

To get more information about TopTools .................... 1-16

2. Operating the OmniBook ................................ 2-1

Starting and Stopping the OmniBook......................... 2-3

To start and stop the OmniBook .......................... 2-3

To reset the OmniBook ................................ 2-4

Using the OmniBook Pointing Devices........................ 2-5

To use the built-in pointing devices ........................ 2-6

To activate full touch pad capabilities ...................... 2-7

To activate full pointing stick capabilities.................... 2-8

To configure pointing devices............................ 2-9

Using the OmniBook Display .............................. 2-10

To adjust the display brightness .......................... 2-10

To extend the life of the display .......................... 2-10

Adjusting the Audio System ............................... 2-11

To adjust the volume manually ........................... 2-11

To adjust the volume in Windows ......................... 2-11

Using the OmniBook Keyboard............................. 2-12

To use the Fn hot keys ................................. 2-13

To use the Windows keys ............................... 2-14

To use the embedded keypad............................ 2-14

To use the ALT GR key................................. 2-15

Checking the Status of the OmniBook ........................ 2-16

To interpret the status lights ............................. 2-16

To interpret the status panel indicators...................... 2-17

Protecting the OmniBook................................. 2-19

Contents-1

To set or change a password............................. 2-20

To delete a password.................................. 2-21

To install McAfee VirusScan ............................. 2-21

To attach a security cable............................... 2-22

To set PC identification ................................ 2-23

To enable hard disk drive lock ........................... 2-23

3. Managing Battery Power................................. 3-1

Monitoring Battery Power................................. 3-3

To check the battery status.............................. 3-4

To respond to a low-battery warning ....................... 3-5

To recharge a battery.................................. 3-5

To replace the main battery ............................. 3-7

To install a second battery .............................. 3-8

Conserving Battery Power ................................ 3-9

To save battery power ................................. 3-9

To set time-outs...................................... 3-10

To get the most from your battery ......................... 3-11

4. Making Connections .................................... 4-1

Using OmniBook Plug-In Modules ........................... 4-3

To replace a plug-in module............................. 4-4

To insert or eject a floppy disk ........................... 4-5

To insert or remove a CD ............................... 4-6

Connecting External Devices .............................. 4-7

To identify connectors for external devices................... 4-8

To connect an external monitor .......................... 4-9

To enable the built-in and external displays .................. 4-9

To change display settings in the BIOS Setup utility ............. 4-9

To connect a parallel device............................. 4-10

To connect a serial device .............................. 4-10

To connect an external keyboard or PS/2 mouse............... 4-11

To connect USB devices................................ 4-11

To connect a television ................................ 4-12

To connect audio devices .............................. 4-12

To make an infrared connection .......................... 4-14

Using PC Cards ........................................ 4-16

To insert a PC Card ................................... 4-16

To remove a PC Card.................................. 4-17

List of tested PC Cards ................................. 4-18

Using Docking Products.................................. 4-19

To install a docking tray................................ 4-19

To dock the OmniBook ................................ 4-20

To undock the OmniBook .............................. 4-22

Contents-2

5. Expanding the OmniBook ................................ 5-1

Installing a Hard Disk Drive ............................... 5-3

To replace the hard disk drive............................ 5-3

To replace the hard disk drive holder ...................... 5-4

To create a Hibernate partition ........................... 5-5

Installing a RAM Expansion Module ......................... 5-6

To install a RAM expansion module ....................... 5-7

To remove a RAM expansion module ...................... 5-8

6. Using the Recovery CD .................................. 6-1

Recovering a factory build ................................ 6-3

To recover the Windows 95 factory installation ................ 6-4

To recover the Windows NT factory installation ............... 6-5

Installing Retail Windows 95............................... 6-6

To install a retail version of Windows 95..................... 6-6

To install video support for retail Windows 95................. 6-8

To install audio support for retail Windows 95 ................ 6-9

To install PC Card support for retail Windows 95 ............... 6-10

To install infrared support for retail Windows 95 ............... 6-10

Installing Retail Windows NT 4.0 ............................ 6-12

To install a retail version of Windows NT 4.0.................. 6-13

To install Service Pack 3 for retail Windows NT 4.0 ............. 6-14

To install video support for retail Windows NT 4.0 .............. 6-15

To install audio support for retail Windows NT 4.0.............. 6-16

To install APM for Windows NT 4.0 ........................ 6-17

To install Card Executive 2.x for retail Windows NT 4.0 .......... 6-18

Recovering OmniBook Files ............................... 6-19

To install the online User’s Handbook ...................... 6-19

To replace a damaged Recovery CD........................ 6-19

To update the OmniBook BIOS ........................... 6-20

7. Troubleshooting ....................................... 7-1

Solving Problems ...................................... 7-3

Accessory Problems .................................. 7-3

Audio Problems ..................................... 7-4

Display Problems .................................... 7-5

Hard Disk Drive Problems .............................. 7-5

Keyboard and Pointing Device Problems .................... 7-6

Infrared Problems .................................... 7-7

Memory Problems.................................... 7-8

PC Card (PCMCIA) Problems ............................ 7-8

Performance Problems ................................ 7-9

Power and Battery Problems............................. 7-10

Printing Problems .................................... 7-12

Serial, Parallel, and USB Problems......................... 7-13

Contents-3

Startup Problems..................................... 7-14

Testing the Operation ................................... 7-15

To create a diagnostic floppy disk ......................... 7-15

To run the diagnostic test ............................... 7-16

8. Specifications and Regulatory Information ................... 8-1

Hardware Specifications ................................. 8-3

Software System Resources................................ 8-5

Safety Information...................................... 8-7

Regulatory Information .................................. 8-10

U.S.A. ............................................ 8-10

Canada ........................................... 8-11

Japan ............................................ 8-11

Europe............................................ 8-12

Contents-4

1

Introducing the OmniBook

Introducing the OmniBook

Congratulations! Your OmniBook sets a new standard in personal computing.

Although it’s compact and easy to carry, the OmniBook is infused with the quality
and attention to detail that are the hallmark of Hewlett-Packard.

The OmniBook Quick Start sheet shows how to get your OmniBook up and running
quickly. This Reference Guide shows how to set up and operate the OmniBook, and it
also shows what to do if you run into trouble.

This table lists other sources of supplementary information about OmniBook
products.

Source Address or Number

Online

User’s Handbook

Online

OmniBook Notes

The introductory Microsoft
manual for Windows 95 or
Windows NT.

OmniBook website http://www.hp.com/omnibook

Corporate Evaluator’s Guide

HP Support Assist CD-ROM See the

This introduces the OmniBook and shows you the OmniBook basics.
It also contains troubleshooting information (Start, Programs,
OmniBook Library).

For late-breaking information available after the manuals were
completed, see OmniBook Notes (Start, Programs, OmniBook
Library).
This is shipped with your OmniBook and contains information about
using the standard features of Windows 95 or Windows NT 4.0.

(http://www2.hp.com/omnibook, European mirror)
The provides information about installing alternate operating

systems, as well as how to configure the OmniBook in a corporate,
networked environment. Located at the OmniBook website.

Support and Service

booklet for telephone numbers.

1-2

Introducing the OmniBook

Taking Inventory

Taking Inventory

The HP OmniBook 7100 represents a new category of HP notebook computers
featuring the latest mobile technologies available. It uses a high-speed Intel Pentium
II processor with MMX technology, a large TFT display, and a high-capacity hard
drive.

This chapter describes

♦ What’s included in the OmniBook shipment.
♦ Available OmniBook accessories.
♦ Description of OmniBook features.

Included in the OmniBook 7100 box

• HP OmniBook 7100.

• 24

• AC adapter (HP F1454A) and power cord.

• Lithium-ion battery (HP F1450A).

• This OmniBook Reference Guide.

• Quick Start sheet.

• Support and Service booklet.

• Working in Comfort booklet.

• List of optional OmniBook accessories.

• OmniBook Recovery CD. Includes Windows recovery,

• Microsoft Windows 95 manual and CD.

–or–
Microsoft Windows NT 4.0 manual.

CD-ROM drive / floppy disk drive (HP F1446A).

x

operating system drivers and online User’s Handbook.

1-3

Introducing the OmniBook

Taking Inventory

To buy OmniBook accessories

Buy OmniBook accessories online! For the latest accessories and options, visit us at

http://www.hp.com/omnibook

them listed here.
At the time of this printing, HP offers a variety of docking solutions, plug-in modules,

and other accessories, including the following:

• Docking system and monitor stand (HP F1477A).

• Mini dock (HP F1452A).

• Port replicator (HP F1451A).

• 24

• LS-120 drive (HP F1448A).

• DVD drive (HP F1447A).

• Lithium-ion battery (HP F1450A).

You can install a second battery in the module bay.

• PC Cards.

• SmartCard.

• Auto / airline adapter (HP F1455A).

• OmniBook carrying case.

CD-ROM drive / floppy disk drive (HP F1446A).

x

. As new accessories become available, you’ll find

1-4

OmniBook features

OmniBook—Front View

Introducing the OmniBook

Taking Inventory

1. Built-in microphone.

2. Status panel.

3. Blue power button (suspends or shuts down the OmniBook).

4. Pointing stick (pointing device).

5. Touch pad (pointing device).

6. Built-in speakers.

7. Plug-in module bay (can contain a CD-ROM / floppy disk drive, LS-120 drive,

DVD drive, or a second battery).

8. Click buttons (for pointing devices).

9. Main battery.

1-5

Introducing the OmniBook

Taking Inventory

10. System-off button (to shut down the OmniBook).

11. Kensington lock slot.

12. Latch to open and close the OmniBook.

OmniBook—Side View

13. AC adapter jack.

14. PC Card slots (upper and lower). Accepts PC Card Types II or III (PCMCIA and

CardBus).

15. Audio jacks (left to right): audio line-in, external microphone, headphone-out.

16. Volume control wheel.

17. PC Card eject buttons (upper and lower PC Card slots). Press once to pop out

the button, and press again to eject the card.

18. Status lights (left to right): power, hard disk activity, charging status.

19. Front infrared port. There is a another infrared port on the rear of the OmniBook.

Windows NT 4.0 does not support infrared communication.

Use this port for wireless data transmission between the OmniBook and another

computer or a printer with an infrared port. You must install infrared drivers.

1-6

Introducing the OmniBook

Taking Inventory

OmniBook—Back View

20. Parallel port (LPT1).
Use this port for a parallel printer.

21. Serial port (COM1).
Use this port for a serial mouse, a modem, or a serial printer.

22. External monitor port.

23. S-video (TV-out) port.

24. Docking port (for HP OmniBook docking products).

25. Universal serial bus port (USB). Windows NT 4.0 does not support USB.

26. PS/2 keyboard or PS/2 mouse port (supports a standard Y adapter).

27. Rear infrared port. There is a another infrared port on the front of the

OmniBook. Windows NT 4.0 does not support infrared communication.

Use this port for wireless data transmission between the OmniBook and another

computer or a printer with an infrared port. You must install infrared drivers.

1-7

Introducing the OmniBook

Setting Up Windows

Setting Up Windows

The OmniBook has either Windows 95 or Windows NT 4.0 factory-installed on the
hard disk drive. When your OmniBook starts up the first time, it takes you through a
series of setup screens, including installation of the operating system.

This section describes how to set up the OmniBook with the factory-installed
Windows operating system.

♦ Setting up the OmniBook for the first time.

1-8

To set up the OmniBook

Introducing the OmniBook

Setting Up Windows

CAUTION

Note

Use only the HP adapter model F1454A with this product. Using any other ac
adapter could damage the OmniBook and may void your warranty. Refer to the
warranty statement for your product.

1. Install the OmniBook’s battery. (See the Quick Start sheet or page 3-7 of this

manual).

2. Connect the power cord to the ac adapter, then plug the cord into an ac outlet.

The indicator light on the ac adapter shines when the adapter is powered.

3. Connect the ac adapter to the OmniBook’s left side, as shown. The OmniBook

battery starts charging.

Let the battery charge a full 24 hours to completely charge the internal clock battery.
Otherwise, the OmniBook may not keep the correct date and time.

4. Press the blue power button.
The Windows 95 or Windows NT Setup program starts automatically.

5. Follow the instructions as they appear on the screen.
During setup, you will be prompted to accept the License Agreement and enter

the Product ID (printed on the Certificate of Authenticity on the Microsoft
Windows manual). If you are prompted to set up a user account and password.
You can either set up the account, or press ESC to skip this step.

1-9

Introducing the OmniBook

Configuring the OmniBook with the BIOS Setup Utility

Configuring the OmniBook with the BIOS
Setup Utility

The BIOS (Basic Input and Output System) Setup utility is a menu-driven utility that
enables you to make changes to the system configuration and tailor the operation of
your OmniBook to your individual work needs.

The settings made in the BIOS Setup utility generally control the hardware and
consequently have a fundamental effect on how the OmniBook operates.

This section describes the BIOS Setup utility menus and options in detail.

To run the BIOS Setup utility

1. Close all applications, then shut down Windows and restart the OmniBook.

2. When you see the HP logo, press F2 to enter the BIOS Setup utility.

3. The pointing devices are not active in the BIOS Setup utility. Press the RIGHT

and LEFT arrow keys to move among menus. Press the DOWN and UP arrow
keys to move among parameters in a menu. Press F5 or F6 to move through
values for the current parameter or press ENTER to change a setting. See the
tables below for more information.

4. After you select the options you want, press F10 or use the Exit menu to exit the

BIOS Setup utility.

If the settings cause a conflict between devices during reboot, the system

prompts you to run BIOS Setup, and the conflicting settings are marked.

1-10

Introducing the OmniBook

Configuring the OmniBook with the BIOS Setup Utility

Main Menu Default

Language Sets the language for this utility and for BIOS

messages.

BIOS Revision Shows the current BIOS version. Detected

System Time Sets the time using 24-hour format. Values

set take effect immediately.

System Date Sets the date using dd/mm/yy format (except

English, which is mm/dd/yy format).

Floppy Drive Sets the floppy drive type. Floppy disk drive

Hard Disk Sets the hard disk drive type and various

parameters.

Quiet Boot When enabled, hides summary of

power-on self-test and messages during boot.

Video Display Device* Sets whether the built-in display

automatically switches to an external display
if one is detected.

Television Type Sets the format (NTSC or PAL) for video

output.

Same as operating
system.

automatically.

type detected and
set automatically.

Hard disk drive
detected and set
automatically.

Enabled

Auto

Varies according to

country.
System Memory Shows the system memory size. 640KB
Extended Memory Shows the extended memory size. Detected

automatically.
* Setting Video Display Device to Both will prevent the OmniBook from suspending when you

close the lid.

1-11

Introducing the OmniBook

Configuring the OmniBook with the BIOS Setup Utility

System Devices Menu Default

Internal Pointing Devices Enables one or both built-in PS/2 devices. Both
External Fn Key Sets whether left-CTRL + left-ALT on an

external keyboard is interpreted as the Fn key.

IDE Controller Enables the primary (hard drive) and secondary

(optional CD-ROM drive) controllers.
FDD Controller Enables the floppy drive. Enabled
Serial Port Sets how the serial port is configured by the

BIOS (specified or automatic).
Base I/O address Sets the I/O address and interrupt. 3F8h, IRQ4
Infrared Port Sets how the infrared port is configured by the

BIOS (specified or automatic).
Mode Sets the hardware to support SIR (Standard IR),

ASK IR (amplitude shift keyed IR), or FIR (Fast IR)

infrared communications. (Driver installation

required.)
Base I/O address Sets the I/O address and interrupt. 2F8h, IRQ3
DMA channel For Fast Ir mode, sets the DMA channel. DMA3
Front/Back Sets which infrared port is active. Back
Parallel Port Sets how the parallel port is configured by the

BIOS (specified or automatic).
Mode Sets the port to normal, bi-directional, EPP, or

ECP.

Enabled

Both

Enabled

Disabled

SIR

Enabled

ECP

Base I/O address Sets the I/O address. 378h
Interrupt Sets the interrupt. IRQ7
DMA channel For ECP mode, sets the DMA channel. DMA3
Audio Sets how the audio system is configured by the

BIOS (specified or automatic).
SB I/O address Sets the Sound Blaster I/O address. 220h
WSS I/O address Sets the Windows Sound System I/O address. 530h
AdLib I/O address Sets the AdLib synthesizer I/O address. 388h

1-12

Enabled

Introducing the OmniBook

Configuring the OmniBook with the BIOS Setup Utility

Interrupt Sets the interrupt. IRQ5
1st DMA channel Sets the DMA channel for playback. DMA1
2nd DMA channel Sets the DMA channel for recording. DMA0
MPU Device Sets how the MIDI capability (hardware

wavetable) is configured by the BIOS (specified

or automatic).
MPU I/O address Sets the MIDI I/O address. 330h
Interrupt Sets the interrupt. IRQ11

Security Menu Default

User Password Is Shows if a user password is set. Clear
Administrator Password Is Shows if an administrator password is set. Clear
Set User Password Press ENTER to set, change, or clear user

password. Password length can be no longer

than 8 characters, 0-9, A-Z.
Set Administrator Password Press ENTER to set, change, or clear

administrator password. This password protects

BIOS Setup settings.
Boot Sets whether a user password is required when

the computer boots.
Resume* Sets whether a user password is required when

resuming from a suspended state.

Undock* Sets whether a user password is required when

undocking the OmniBook.

Disabled

Enabled

Enabled

Disabled

Hard Disk Drive Lock Encodes the current user password (or

administrator password if that is the only

password set), on the hard disk drive.
Floppy Boot Sets whether the floppy drive is a boot device. Enabled
* Resume and Undock options are available only if Boot option is enabled.

Disabled

1-13

Introducing the OmniBook

Configuring the OmniBook with the BIOS Setup Utility

Power Menu Default

Power Management Mode Disables time-outs, selects a combination of

time-outs, or allows customized time-outs.
Smart CPU Mode Enables automatic CPU power savings. Absence

of keyboard, mouse, and hard disk activity could

cause slower CPU response.
Standby Time-out Sets the period of inactivity after which the

computer goes from On to Standby power mode.
Suspend Time-out Sets the period of inactivity after which the

computer goes from Standby to Suspend power

mode. (Skips Standby mode if that time-out is

disabled.)
Hibernate Time-out Sets whether the computer goes from Suspend

to Hibernate power mode after the indicated

period of inactivity. (Skips Suspend mode if that

time-out is disabled.)
Hard Disk Time-out Sets the period of hard disk inactivity after

which the hard disk stops spinning.
Time-out on AC Sets whether power management time-outs

occur while the ac adapter is connected.
Power Button Mode Sets the action of the blue power button when

pressed for less than 4 seconds.
Resume on Modem Ring Sets whether the system resumes from Suspend

if a ring signal is received.

Max Power
Savings

Off

2 minutes

4 minutes

4 hours

2 minutes

Disabled

Suspend

Enabled

Resume on Time of Day Sets whether the system resumes from Suspend

at a defined time of day.
Resume Time Sets the 24-hour time when the system resumes

from Suspend if enabled.
Auto Suspend on Undock Sets whether the OmniBook suspends after

undocking.

1-14

Disabled

When Lid
Closed

Introducing the OmniBook

Configuring the OmniBook with the BIOS Setup Utility

Boot Menu Default

Diskette Drive
Hard Drive
CD-ROM Drive

Exit Menu

Save Changes and Exit Saves Setup changes, exits, and reboots.
Discard Changes and Exit Discards Setup changes since last save, exits,

Get Default Values Restores default settings, stays in Setup. Does

Load Previous Values Discards Setup changes since last save, stays

Save Changes Saves Setup changes, and stays in Setup.

Shows the order of boot devices. Move the

entries to change the order.

and reboots. Does not affect Security, date, or

time changes.

not affect Security, date, or time changes.

in Setup. Does not affect Security, date, or

time changes.

Security settings are saved when changed.

1. Diskette drive

2. Hard drive

3. CD-ROM drive

1-15

Introducing the OmniBook

Configuring the OmniBook with TopTools

Configuring the OmniBook with TopTools

HP TopTools is for network managers and administrators with responsibilities for
computer system management. It offers configuration and security options that allow
you to check what hardware and software components are installed on your
computer and how well they are working. This section describes how to

♦ Install and run TopTools.
♦ Get more information about TopTools.

To install TopTools

The TopTools package is included with the OmniBook, but you must install it before
you can use it. On Windows NT systems, you will need administrator privileges to

install TopTools software

.

1. Start Windows, if it is not already running.

2. Click Start, Programs, HP DMI, Setup.

To run TopTools

TopTools may be run locally on a PC or remotely by a network administrator.

• To run TopTools locally, click Start, Programs, HP DMI, HP TopTools.

To get more information about TopTools

For information on manageable HP PCs, HP TopTools, DMI, and how they lower
PC operating costs, see the see the HP website at http://www.hp.com/toptools.

1-16

2

Operating the OmniBook

Operating the OmniBook

This chapter introduces the OmniBook and helps you get familiar with basic
operation, including

♦ Starting and stopping the OmniBook.
♦ Using the OmniBook pointing devices.
♦ Managing pointing devices.
♦ Using the OmniBook display.
♦ Adjusting the audio system.
♦ Using the OmniBook keyboard.
♦ Checking the status of the OmniBook.
♦ Protecting the OmniBook.

2-2

Operating the OmniBook

Starting and Stopping the OmniBook

Starting and Stopping the OmniBook

You can easily start and stop your OmniBook using the blue power button. However,
at certain times, you may want to use other methods for starting and stopping your
OmniBook—depending on power considerations, types of active connections, and

start-up time.

To start and stop the OmniBook

When you The OmniBook enters To exit this mode

Press Fn+S

–or–
allow time-out.

Press blue power button
–or–
click Start, Suspend**
–or–
close the lid***
–or–
allow time-out.
Press Fn+F12
–or–
allow time-out.

Click Start, Shut Down
(recommended)
–or–
Press and hold the blue
power button until the
display shuts down.

* A plug-and-play operating system, such as Windows 95, can restore network connections when you turn on the OmniBook. For

Windows NT 4.0 or a different operating system, you may have to reset the OmniBook or restart the operating system to
restore them.

** Windows 95 only.

*** If you set the Video Display Device to Both (in BIOS Setup), the OmniBook will not suspend when you close the lid.

Standby Mode

Saves minimal power.
Turns off the display only.
Restarts quickly.
Maintains network connections.

Suspend Mode

Saves significant power.
Turns off the display.
Saves current session to RAM.
Restarts quickly.
May restore network connections.

Hibernate Mode

Saves maximum power.
Saves current session to disk, shuts down.
May restore network connections.*

Off Mode

Saves maximum power.
Turns off without saving current session.
At startup, resets everything, starts a new session, and
restores network connections.

*

Press any key or move a pointing device
to display your current session
(“Instant-On”).

Press the blue power button to display
your current session
(“Instant-On“).

Press the blue power button to restart
and restore your previous session.

Press the blue power button to restart
with a new session.

2-3

Operating the OmniBook

Starting and Stopping the OmniBook

To reset the OmniBook

If Windows or the OmniBook stops responding, you can reset the OmniBook and
restart Windows.

1. If possible, shut down Windows.

2. Press and hold the blue power button until the display shuts down.
–or, if this fails–

Insert a pen or straightened paper clip into the recess on the right side of the

OmniBook, as shown.

3. After the computer shuts down, press the blue power button to turn it on.

2-4

Operating the OmniBook

Using the OmniBook Pointing Devices

Using the OmniBook Pointing Devices

Two pointing devices (pointing stick and touch pad) are built into your OmniBook.
The default pointing device driver (PS/2 TrackPoint), supports the enhanced
features of the pointing stick and basic features of the touch pad.

You can customize the OmniBook to support enhanced touch pad features. If you
do this, keep in mind that you are selecting enhanced features for the touch pad
only. You cannot activate enhanced features for both simultaneously.

This section describes how to

• Use the built-in pointing devices.

• Activate full touch pad capabilities.

• Activate full pointing stick capabilities.

• Configure pointing devices.

1. Pointing stick (pressure-sensitive pointing device).

2. Touch pad (touch-sensitive pointing device).

3. Click buttons.
Both pointing devices use these click buttons, which work like the right and left

buttons on a standard mouse. What the buttons do depends on the software
being used.

2-5

Operating the OmniBook

Using the OmniBook Pointing Devices

To use the built-in pointing devices

1. Place your hands in the typing position.

Pointing stick.

2.

you want the pointer to move. Pressing away from you moves the pointer up the
screen; pressing toward you moves the pointer down the screen.

Touch pad.

want the pointer to move.

3. Use the left and right click buttons, which function like the left and right buttons

on a mouse, to make your selection.

• To open an application, move the pointer over the icon, then press the left

button twice rapidly.

• To make menu selections, move the pointer to the item and press the left

button once.

• To open the shortcut menu for an item, move the pointer over the item and

click the right button.

• To drag an item, move the pointer over the item. Press and hold the left

button while you move the pointer to the new location. Release the button.

With your index finger, press the pointing stick in the direction

Move a thumb or finger across the touch pad in the direction you

2-6

Operating the OmniBook

Using the OmniBook Pointing Devices

To activate full touch pad capabilities

The built-in pointing stick driver supports only basic touch pad features. To activate
full touch pad capabilities, you have to

• Remove the pointing stick driver and select a new mouse driver.

• Disable the pointing stick.

• Install touch pad support.

1. Select a new mouse driver and remove the pointing stick driver

1. From the Start menu, click Settings, Control Panel.

2. Double-click Add/Remove Programs and remove IBM TrackPoint Support.

3. Double-click Mouse, then click General.

4. Click Change and then select Show All Devices.

5. Under Manufacturers, click Standard Mouse Types.

6. Under Models, change the mouse type to Standard PS/2 Port Mouse, then click

OK.

7. Click Yes to any questions.

2. Disable the pointing stick

1. From the Start menu, shut down, then restart the OmniBook.

2. When you see the HP logo, press F2 to enter the BIOS Setup utility.

3. Select the System Devices menu.

4. Highlight Internal Pointing Devices and select Touch Pad.

5. Press F10 to save and exit.

3. Install touch pad support

For Windows 95.

•

For Windows NT

•

Run C:\Omnibook\Drivers\Win95\Touchpad\Setup.exe.

. Run C:\Omnibook\Drivers\Nt40\Touchpad\Install.exe.

2-7

Operating the OmniBook

Using the OmniBook Pointing Devices

To activate full pointing stick capabilities

If you have activated full touch pad capabilities, you can use this procedure to

switch back to full pointing stick capabilities. You’ll need to do the following:

• Remove the touch pad driver (Windows 95 only).

• Enable the pointing stick.

• Install pointing stick support.

1. Remove the touch pad driver (Windows 95 only)

• From Control Panel, click Add/Remove Program and remove touch pad

support.

2. Enable the pointing stick

1. From the Start menu, shut down, then restart the OmniBook.

2. When you see the HP logo, press F2 to enter the BIOS Setup utility.

3. Select the System Devices menu.

4. Highlight Internal Pointing Devices and select Pointing Stick. (Choose Both if

you want basic touch pad features available.)

5. Press F10 to save and exit.

3. Install pointing stick support

• From Control Panel, open Mouse, General and change the mouse type--click

Have Disk and point to the directory listed below and select PS/2 TrackPoint.

For Windows 95

c:\omnibook\drivers\win95\trackpnt.

For Windows NT 4.0

c:\omnibook\drivers\nt40\trackpnt.

2-8

Operating the OmniBook

Using the OmniBook Pointing Devices

To configure pointing devices

• To customize the operation of all pointing devices (pointing stick, touch pad,

and external PS/2 or serial mouse), in Control Panel open Mouse. You can
change left and right button actions, double-click speed, pointer speed and tail,
and more.

• To customize special pointing stick features, click the pointing stick icon on the

taskbar or open TrackPoint in Control Panel.

2-9

Hint

Operating the OmniBook

Using the OmniBook Display

Using the OmniBook Display

This section describes

♦ How to adjust the display brightness.
♦ How to extend the life of the display.

To adjust the display brightness

The OmniBook uses special key combinations, called hot keys, to control brightness.

• Press Fn+F1 to decrease the brightness.

• Press Fn+F2 to increase the brightness.

To maximize your battery operating time, set the brightness to the lowest
comfortable setting, so that the internal light uses less power.

To extend the life of the display

Observe the following guidelines to maximize the life of the backlight in the
OmniBook display.

• Set the brightness to the lowest comfortable setting (Fn+F1).

• When working at your desk, connect an external monitor and turn off the

internal display (Fn+F5).

• Avoid using a screen saver or other software that prevents the OmniBook from

changing to Suspend or Standby mode after a time-out period.

• Do not disable Suspend or Standby time-outs.

• If you are using ac power and have no external monitor attached, change to

suspend or standby when not in use.

2-10

Operating the OmniBook

Adjusting the Audio System

Adjusting the Audio System

The OmniBook supports Sound Blaster Pro-compatible sound and the Microsoft
Windows Sound System. This section describes

• How to adjust the volume manually.

• How to adjust the volume in Windows.

To adjust the volume manually

• To increase the volume, press Fn+UP-ARROW.

--or-­ Roll the volume control wheel towards the front of the OmniBook.

• To decrease the volume, press Fn+DOWN-ARROW.

--or-­ Roll the wheel towards the rear of the OmniBook.

To adjust the volume in Windows

1. Click the speaker symbol in the taskbar.

2. Drag the volume control bar up or down to adjust the volume.

2-11

Operating the OmniBook

Using the OmniBook Keyboard

Using the OmniBook Keyboard

WARNING

Improper use of keyboards and other input devices has been associated with
ergonomic injury. For information about reducing your risk, see the
in Comfort

document shipped with your OmniBook, or visit our ergonomics

Working

website, http://www.hp.com/ergo.

This section describes the OmniBook’s keyboard features, including how to

♦ Use the Fn hot keys.
♦ Use the Windows keys.
♦ Use the embedded keypad.
♦ Use the ALT GR key on a non-US keyboard.

2-12

Operating the OmniBook

Using the OmniBook Keyboard

To use the Fn hot keys

The combination of the Fn key plus another key creates a hot key—a
shortcut key sequence—for various system controls. The OmniBook
keyboard shows the Fn hot keys labeled in gray.

Pressing these keys Does this

Fn + F1 Decreases the display’s brightness.
Fn + F2 Increases the display’s brightness.
Fn + F5 Switches among the built-in display, an external display, and

simultaneous displays.

Fn + F6 (hold) For use with two batteries: Briefly displays the individual battery

status for each battery, then resumes displaying the combined
battery status. For complete information about battery status, see
page 2-17.

Fn + F8 Toggles the built-in keypad on and off. Does not affect an external

keyboard. If Num Lock is on, then the numeric functions are active;

otherwise, cursor control is active.
Fn + F12 Enters Hibernate mode.
Fn + S Enters Standby mode.
Fn + R Enters Suspend mode.
Fn + F Toggles between front and rear infrared ports. Windows NT 4.0

does not support infrared communication.
Fn + Nm Lk Toggles Scroll Lock on and off.
Fn + Up Arrow Increase the volume.
FN + Down Arrow Decreases the volume.

2-13

Operating the OmniBook

Using the OmniBook Keyboard

To use the Windows keys

There are two Windows keys on the keyboard.

The one next to the Fn key brings up the Windows Start menu.

The one at the top center of the keyboard brings up the shortcut menu
for the current application. This is the same menu that appears when
you click the right mouse button while pointing at the application.

To use the embedded keypad

When the embedded keypad on the OmniBook’s built-in keyboard is active, two
options are possible.

Num Lock on

Num Lock off

To identify the icons that show the status of Num Lock and the embedded keypad,
go to page 2-17.

1. Press Nm Lk to turn Num Lock on or off.

2. Press Fn+F8 to turn on the embedded keypad.
–or–
To temporarily turn on the embedded keypad, hold Fn while typing a key.

2-14

Keys change to the numeric or arithmetic designations on the
slanted faces of the keys.

Keys change to cursor control keys.

Operating the OmniBook

Using the OmniBook Keyboard

To use the ALT GR key

Non-U.S. keyboards have an ALT GR key to the right of the spacebar. This is a shift
key providing access to certain keyboard characters.

• For a character in the lower-right corner of a key, press and hold ALT GR to type

the character.

• For a character in the upper-right corner of a key, press and hold SHIFT and

ALT GR to type the character.

Shift

Unshifted

ALT GR

2-15

Operating the OmniBook

Checking the Status of the OmniBook

Checking the Status of the OmniBook

This section describes how to interpret the status lights and the status panel
indicators.

To interpret the status lights

The OmniBook has status lights that report power status and drive activity. When the
CD-ROM / floppy disk drive is installed in the module bay, the following lights are
present on the front of the OmniBook.

1. Floppy disk drive light.

• Steady green light. OmniBook reading from or writing to floppy disk drive.

2. CD-ROM drive light.

• Steady green light. OmniBook reading from CD-ROM drive.

3. Power status light.

• Steady green light. OmniBook is on.

• Steady amber light. OmniBook is in Suspend or Standby mode.

• No light. OmniBook is in Off or Hibernate mode.

• Alternating green and amber light. OmniBook failed when resuming.

4. Disk drive activity light.

• Steady green light. OmniBook reading from or writing to hard disk drive.

5. Charging status light.

• Steady green light. The ac adapter is connected and battery is full.

• Blinking green light. The ac adapter is connected and battery is charging.

• No light. The ac adapter is not connected.

2-16

Operating the OmniBook

Checking the Status of the OmniBook

To interpret the status panel indicators

The OmniBook status panel, located above the keyboard, contains indicators that
show the current power status, drive status, and keyboard status.

Power Status Icons

Indicator Meaning

AC power. The ac adapter is connected.

Battery status. Shows the approximate charge level of the battery
relative to a full charge. Each bar (displayed from right to left),
represents a 10% charge.

Battery presence. The upper and lower triangles indicate the
presence of main (upper) and second (lower) batteries. A triangle
blinks slowly when that battery is charging. The main battery
charges first, discharges last.

If two batteries are installed, the gauge reports the percent of total
charge. For example, if the main battery is 50% and the second
battery is empty then the gauge would read 25%. You can press

Fn + F6 at any time to see the status of each individual battery.

hold

and

Battery low. No battery bars showing; the triangles indicate the
presence of battery. The OmniBook also beeps.

Defective battery. No battery bars showing and no triangles
indicating presence of battery. No charging even though ac power is
present.

Overheated battery. The battery is too hot to charge. Not
necessarily a defective battery.

2-17

Operating the OmniBook

Checking the Status of the OmniBook

Drive Status Icons

Indicator Meaning

Keyboard Status Icons

Indicator Meaning

Drive activity. The OmniBook is accessing either the hard disk

drive or any of the following drives in the module bay: CD-ROM
drive, DVD drive, or LS-120 drive.

Floppy disk drive. The OmniBook is accessing the floppy disk
drive.

PC Card. There is activity between the PC Card and the computer.

Caps Lock. Caps Lock is active.

Num Lock. Num Lock is active.

Keypad Lock. The built-in embedded keypad is active (Fn+F8). Num

Lock must also be on for the numeric keys. Otherwise, cursor keys
are active.

Scroll Lock. Scroll Lock is active.

2-18

Operating the OmniBook

Protecting the OmniBook

Protecting the OmniBook

Your OmniBook provides several ways for you to identify and protect your
computer. This section describes how to

• Set or change a password.

• Delete a password.

• Install McAfee VirusScan.

• Attach a security cable.

• Set unique PC identification.

• Enable drive lock protection.

2-19

Operating the OmniBook

Protecting the OmniBook

To set or change a password

The OmniBook provides two levels of password protection—user password
protection and administrator password protection. You cannot set the user password
until you set an administrator password.

If password protection is set, then you will be prompted to enter a password
whenever you reset or turn on the computer (depending on your setting). You
cannot use the computer until you enter the correct password.

To set, change, or delete password protection for this OmniBook, use the BIOS Setup
utility.

1. From the Start menu, shut down, then restart the OmniBook.

2. When you see the HP logo, press F2 to enter the BIOS Setup utility.

3. Select the Security menu.

4. Select Set Administrator Password, then press ENTER.

5. Type the new password, then press ENTER. The password can contain up to
eight alphanumeric characters, and it is not case-sensitive.

6. Type the password again to confirm, then press ENTER.

7. Under Password Required To, choose when the password will be required.

• Select Boot to require password when booting the OmniBook.

• Select Resume to require password when resuming from Suspend.

• Select Undock to require password when undocking the OmniBook.

8. If desired, repeat this procedure for Set User Password.

9. Press F10 to Save and Exit the BIOS Setup utility.

Note

If you forget a password, call Customer Support at the number listed in the Support
and Service booklet to determine the proper removal procedure.

2-20

Operating the OmniBook

Protecting the OmniBook

To delete a password

You can use this procedure to delete either a User or an Administrator password. If
you delete an administrator password, the OmniBook automatically deletes the user
password as well.

1. From the Start menu, shut down, then restart the OmniBook.

2. When you see the HP logo, press F2 to enter the BIOS Setup utility.

3. Select the Security menu.

4. Select Set Administrator Password, then press ENTER.

5. Type the current password, then press ENTER.

6. Press ENTER at the Enter New Password prompt.

7. Press ENTER at the Confirm New Password prompt.

8. Press Continue.

9. Press F10 to Save and Exit the BIOS Setup utility.

To install McAfee VirusScan

The OmniBook comes equipped with McAfee VirusScan, which currently detects
over 13,500 viruses. As an HP OmniBook owner, you are entitled to 90 days free
support from McAfee and one free upgrade to VirusScan. For details, click Start,
Programs, McAfee VirusScan, Readme.

Before you can use VirusScan, you need to install it.

1. From the Start menu, click Programs, McAfee VirusScan, Setup.

2. Follow the instructions as they appear on the screen.

Once installed, you can get detailed online instructions under VirusScan Help. (Click
Start, McAfee VirusScan, VirusScan, Help.)

2-21

Operating the OmniBook

Protecting the OmniBook

To attach a security cable

Your OmniBook has a built-in connector that allows you to secure the OmniBook
with a cable. The Kensington MicroSaver lock system works with this connector and
is available at many computer stores.

1. Wrap the cable around a stationary object, such as a table leg.

2. Loop the cable to create a slip knot around the stationary object—make sure it

can’t slip off

3. Insert the lock into one of the OmniBook security connectors and release the
key. Store the key in a safe place away from the OmniBook.

2-22

Operating the OmniBook

Protecting the OmniBook

To set PC identification

You must have administrator password authority to set a PC identification number.

1. If you have not already installed HP TopTools, do so now (page 1-16).

2. Click Start, then click HP TopTools.

3. Click Tools, then click Protect Tools.

4. Type your administrator password.

5. Click Security.

6. In the “Tattooing String” box, type the unique set of characters which will

identify your PC. You can type up to 80 characters including spaces and special
characters. Do not press ENTER when typing. The string wraps automatically.

CAUTION

To enable hard disk drive lock

Hard disk drive lock helps you keep your information secure.

When you enable hard disk drive lock, the current user password (or
administrator password if that is the only password set) is encoded on the hard
disk drive.

If you move the hard disk drive to another OmniBook, you can't access the drive
until you set the user (or administrator) password to match the drive's password

After you match the drive's password, you can change the OmniBook (and
drive) password. If you forget the password, you cannot recover your data.

1. From the Start menu, shut down, then restart the OmniBook.

2. When you see the HP logo, press F2 to enter the BIOS Setup utility.

3. From the Security menu, enable Password Required To Boot.

4. From the Security menu, enable Hard Disk Drive Lock.

5. Press F10 to save and exit the BIOS Setup utility.

2-23

.

3

Managing Battery Power

Managing Battery Power

The OmniBook conserves power by using Advanced Power Management (APM),
software that controls battery charging and power drain.

If you re using Windows 95
If you re using Windows NT 4.0

instructions).
The OmniBook provides several safeguards so you won’t be surprised by a

dead-battery condition, including the following:

♦ The battery status indicator shows the remaining battery charge.
♦ Built-in warnings are displayed for low-battery conditions.
♦ The OmniBook automatically turns off when the battery charge gets too

low—your session continues when you start recharging the battery or insert
a fresh battery.

Data on any of the drives is not affected by a low battery—unless the battery runs
down completely while writing data to the drive, or if the battery in a PC RAM card is
also low.

, APM is preinstalled on the OmniBook.

, you’ll need to install APM (see page 6-17 for

3-2

Managing Battery Power

Monitoring Battery Power

Monitoring Battery Power

The primary source of power for the OmniBook is its rechargeable battery pack. You
can use the ac adapter to recharge the battery—or to run on ac power to preserve

the battery. You can also install a second battery in the plug-in module bay for
increased battery time.

Important

Running external connections is a power-intensive operation that significantly
shortens the length of a battery session. Whenever possible, connect the ac adapter
when using external connections.

In addition to the replaceable battery, there is a permanent, internal backup battery,
which recharges whenever the OmniBook is on or connected to ac. It maintains
certain internal settings, such as the clock.

This section describes how to

♦ Check the battery status.
♦ Respond to a low-battery warning.
♦ Recharge a battery (primary or secondary).
♦ Replace the main battery.
♦ Install a second battery.

3-3

Managing Battery Power

Monitoring Battery Power

To check the battery status

From the Status Panel

Shows the approximate charge level of the battery relative to a full
charge. Each bar (displayed from right to left), represents a 10%

Full battery

Low battery

charge.
The upper and lower triangles indicate the presence of main (upper)

and second (lower) batteries. A triangle blinks when that battery is
charging. The main battery charges first, discharges last. See “Battery

Status” on page 2-17 for more information about the battery
indicators.

The battery charge is critically low. The OmniBook also beeps.

No battery activity; no charging.

Defective battery

The battery is too hot to charge. Not necessarily a defective battery.

Overheated battery

From the Windows Taskbar

• Move the pointer onto the power icon at the right end of the taskbar. If you are

using Windows NT 4.0, you’ll need to install Advanced Power Management to
display the power icon (see page 6-17). The approximate battery charge is
displayed as a percentage or in hours.

• Double-click the power icon on the taskbar to open the Battery Meter window.

From Windows

• Click My Computer, Control Panel, Power. This provides access to all options
associated with reporting of power information by Windows.

On the Battery

• While the battery is out of the computer, press the button on the rear of the
battery. The lights show the approximate charge level—each light representing
20% of a full charge.

3-4

Managing Battery Power

Monitoring Battery Power

To respond to a low-battery warning

When battery power is critically low, you are alerted by one or more of the following:

• The battery indicator in the status panel appears empty.

• The computer emits a warning beep. This reminds you to save your work.

• If the OmniBook has been off, you will not be able to turn it on.

The OmniBook automatically hibernates to preserve your current session. (If
Hibernate is disabled in the BIOS Setup utility, then your data is not protected.)
However, the data could be affected if the battery runs down completely while
writing data to the drive.

You won’t be able to restart until you restore power by one of the following actions:

• Plug in the ac adapter.

–or–

• Replace the main battery with one that is charged.

–or–

• Install a charged second battery in the plug-in module bay.

CAUTION

To recharge a battery

The ac adapter is normally warm to the touch whenever it s plugged into an ac
outlet. The OmniBook is normally warm while it
briefcase or other confined space as this may cause the battery to overheat.

1. Connect the power cord to the ac adapter, then plug the cord into an ac outlet.
The indicator light on the ac adapter shines when the adapter is on. If the ac
adapter does not light, make sure that cord is not damaged.

2. Connect the ac adapter to the OmniBook’s left side, as shown in the following
illustration.

s charging. Don t charge it in a

3-5

Managing Battery Power

Monitoring Battery Power

Charging time

Charging the battery takes about 2 hours to fully charge.

Battery life

With a full charge, battery life in Suspend mode is about 48 hours. If the computer is
in use, typical battery life can last up to 3 to 3.5 hours, depending on your level of
use and your power management settings (see page 1-14).

Optimum Charging

To get the longest battery operating time, continue charging until the OmniBook
battery is fully charged, indicated by the following:

• Charging light on the front of the computer stops blinking.

• Status panel battery indicator (up or down triangle) stops blinking.

Because of rounding, a battery indicator can show a full battery before it’s fully
charged. The indicators stop blinking only when the battery is actually full.

You can continue working while the battery is charging.

3-6

To replace the main battery

Managing Battery Power

Monitoring Battery Power

WARNING

CAUTION

Do not mutilate, puncture, or dispose of batteries in fire. A battery can burst or
explode, releasing hazardous chemicals. A rechargeable battery must be
recycled or disposed of properly. For more information about battery safety,
see page 8-8.

If you have any unsaved data, it (and your current work session) will be lost when
you remove the battery unless the computer is connected to ac power or a second

battery is installed.

1.

Important

2. Plug in the ac adapter.

–or–

From the Start menu, shut down the OmniBook.

3. Slide and hold the release latch, then pull out the module, as shown.

. Save your work.

Hint

4. Slide the charged battery into the OmniBook until it clicks into place.

The battery module fits into either the module bay or the battery bay. Slide the front
panel of the battery right or left so that it fits into the desired bay.

3-7

Managing Battery Power

Monitoring Battery Power

To install a second battery

The OmniBook’s plug-in module bay accepts a second battery. See page 4-4 for more
information about plug-in modules.

When a second battery is installed, the lower triangle appears next to the battery
icon in the status panel.

1. From the Start menu, shut down the OmniBook. (This is not necessary if you are
removing a battery from the plug-in module bay and inserting another battery.)

2. Slide and hold the release latch, then pull out the module, as shown.

3. Slide the front panel of the battery so that it fits into the bay, then slide it into the
module bay until it clicks into place.

3-8

Managing Battery Power

Conserving Battery Power

Conserving Battery Power

The OmniBook uses Advanced Power Management (APM) to conserve battery
power. You can take steps to optimize your battery operating time. This section
describes how to

♦ Save battery power.
♦ Set time-outs.
♦ Get the most from your battery.

To save battery power

Follow these suggestions to conserve battery power.

• Plug in the ac adapter, especially while using the floppy disk drive, the CD-ROM
drive, or any external connections.

• Put the OmniBook in Suspend mode whenever you are not using it for a short
while: close the lid, or press the blue power button for approximately 1 second,
or select Start menu, Suspend.

• Put the OmniBook in Hibernate mode whenever you want to save your current
session, but will not be using the computer for several hours or more (Fn+F12).

• Shut down the OmniBook whenever you will not be using it for several hours or
more. Click Start, Shut Down. The current session is not saved.

• Turn the brightness of the display down to the lowest comfortable level. This
reduces the backlight power and extends the life of your OmniBook display.

• Set the automatic time-out settings to emphasize saving power (page 3-10).

• If you work with an application that uses the serial port or a PC Card, exit the

application when you are done using it.

• If you have an I/O PC Card—that is, a PC Card having an external connection,
such as a modem or network card—remove it when you are not using it. Some
I/O cards use significant power, even while they’re inactive.

3-9

Managing Battery Power

Conserving Battery Power

To set time-outs

The BIOS Setup utility includes settings for automatic time-outs at specified periods
of inactivity. There are four different time-outs for different levels of power and
conservation.

1. From the Start menu, shut down then restart the OmniBook.

2. When you see the HP logo, press F2 to enter the BIOS Setup utility. Active keys
are described along the bottom of the screen. (The touch pad does not work in
Setup.) Help information for the highlighted item appears in the right-hand
sidebar in the display.

3. Select the Power menu.

4. Select Power Management Mode. (Press the spacebar, F5, or F6 to pick an
option other than Disabled.)

Maximum Power Savings

savings (relatively short time-outs).

Maximum Performance

some power conservation (relatively long time-outs).

Customized

Time-out, Suspend Time-out, Hibernate Time-out, and Hard Disk Time-out. For
definitions of these power modes, see page 2-3.

5. Optional. Choose a setting for Time-Out On AC. If you want the time-outs to
occur even when the OmniBook is connected to ac power, choose Enabled. To
prevent time-outs while the OmniBook is plugged in, choose Disabled (default
setting).

6. Press F10 to save and exit the BIOS Setup utility.

: You determine each setting for Smart CPU Mode, Standby

: The time-out settings are defined for best power

: The time-out settings are set for fast performance with

3-10

Managing Battery Power

Conserving Battery Power

To get the most from your battery

The following are some further suggestions for the best management of your
OmniBook batteries.

• Do not leave batteries unused for long periods of time. If you have more than
one, rotate them.

• If you normally use ac power, make a practice of at least once a week using the
battery as your power source.

• Unplug the ac adapter when the computer is not in use.

• To preserve the life of your battery, be sure to charge the battery regularly.

• For long-term storage, the battery must be charged at 20-50% to save capacity

loss by self-discharge and to avoid deterioration of battery performance. In a
discharged condition, the battery voltage decreases faster. Storage in a 100%
charged condition can cause higher self-discharge and deterioration of
discharge capacity—even after recharging—compared to storage in a 20-50%

charged condition.

3-11

4

Making Connections

Making Connections

This chapter describes procedures to expand the capabilities of your OmniBook,
including

♦ Using OmniBook plug-in modules.
♦ Connecting external devices.
♦ Using PC Cards.
♦ Using docking products.

4-2

Making Connections

Using OmniBook Plug-In Modules

Using OmniBook Plug-In Modules

The plug-in module bay can hold a CD-ROM / floppy disk drive, an LS-120 drive, a
DVD drive, or a second battery. This documentation describes the module that
shipped with the OmniBook—the CD-ROM / floppy disk drive. If you’ve purchased

other accessory modules, refer to the accessory documentation that accompanied
them for instructions.

This section describes how to

♦ Replace a plug-in module.
♦ Insert or eject a floppy disk.
♦ Insert or remove a CD.

4-3

Making Connections

Using OmniBook Plug-In Modules

To replace a plug-in module

Important

If you are inserting or removing a CD-ROM / floppy disk drive, LS-120 drive, or DVD
drive, shut down the OmniBook.

1. From the Start menu, shut down the OmniBook. (This is not necessary if you are
removing a battery from the plug-in module bay and inserting another battery.)

2. Slide and hold the release latch, then pull out the module, as shown.

3. Slide the new plug-in module into the OmniBook until it clicks into place.

4-4

To insert or eject a floppy disk

Making Connections

Using OmniBook Plug-In Modules

CAUTION

Do not remove a floppy disk while the OmniBook is actively reading or writing
data. Otherwise, you could lose data or the OmniBook could stop responding.

1. Hold the disk with its face up, then slide it into the floppy disk drive slot until it
clicks into place.

2. To remove the floppy disk, press the eject button on the front of the drive.

4-5

Making Connections

Using OmniBook Plug-In Modules

To insert or remove a CD

CAUTION

Do not remove a CD while the OmniBook is actively reading data. Otherwise,
the OmniBook could stop responding and you could lose data.

1. Press the button on the face of the CD-ROM drive. If one is present, be sure to
remove the cardboard packing insert.

2. Place the CD into the drive (label facing up) and gently press down to seat the
CD on the spindle–or–remove the CD.

3. Slide the CD-ROM tray back into the module to close it.

If you lose power to the OmniBook, or if you have removed the CD-ROM module
from the OmniBook, you can manually open the CD-ROM drive to remove a CD.

• Insert a straightened paper clip into the recessed hole on the front of the
CD-ROM drive, as shown above.

4-6

Making Connections

Connecting External Devices

Connecting External Devices

You can expand the OmniBook’s capabilities by connecting other devices.

Note

Before you connect any device, check the documentation that came with the
equipment to see if you need to make any settings or adjustments to the equipment
before using it. This might include setting switches to configure the equipment so
that it will operate properly with the OmniBook and the software you plan to use.

This section describes how to

♦ Identify connectors for external devices.
♦ Connect an external monitor.
♦ Enable the built-in and external displays.
♦ Change display settings.
♦ Connect a parallel or serial device.
♦ Connect an external PS/2 keyboard or PS/2 mouse.
♦ Connect a universal serial bus (USB) devices.
♦ Connect a television.
♦ Connect audio devices.
♦ Make an infrared connection.

4-7

Making Connections

Connecting External Devices

To identify connectors for external devices

The following graphic describes the available connectors for external devices. Refer
to it, if necessary, when following the procedures in this section.

1. Parallel port (LPT1).

Use this port for a parallel printer.

2. Serial port (COM1).

Use this port for a serial mouse, a modem, or a serial printer.

3. External monitor port.

4. S-video (TV-out) port.

5. Docking port.

6. Universal serial bus port (USB).

7. PS/2 keyboard or PS/2 mouse port (supports the HP F1469A Y adapter).

8. Back infrared port. There is a second infrared port on the front of the OmniBook.

Use this port for wireless data transmission between the OmniBook and another

computer or a printer with an infrared port. You need to install the infrared
drivers.

4-8

Making Connections

Connecting External Devices

To connect an external monitor

You can connect a VGA, SVGA, XGA, or an SXGA monitor to your OmniBook. The

OmniBook’s internal display supports standard XGA mode (1024 by 768 pixels).

1. Press the blue power button for one second to suspend the OmniBook.

2. Connect the monitor cable to the monitor, then to the VGA port on the back of
the OmniBook.

3. Connect the monitor to a power source and turn it on.

4. Press the blue power button to turn on the OmniBook.

5. If the external monitor has a different resolution from the internal display, adjust
the display properties (My Computer, Control Panel, Display, Settings).

To enable the built-in and external displays

• For a temporary change, press Fn+F5 to cycle through the display options
(Internal, External, Both).

–or–
For a permanent change, change the settings in the BIOS Setup utility (see the

following topic).

To change display settings in the BIOS Setup utility

1. From the Start menu, shut down, then restart the OmniBook.

2. When you see the HP logo, press F2 to enter the BIOS Setup utility.

3. From the Main menu, use the down arrow to highlight Video Display Device.

4. Press ENTER to view choices.

5. Select Auto (automatically detects external monitor) or Both.

6. Press F10 to save settings and exit Setup.

4-9

Making Connections

Connecting External Devices

To connect a parallel device

The parallel port uses a standard 25-pin connector, most commonly used for
connecting a printers. These include dot-matrix, ink-jet, and laser printers. The
parallel port supports both EPP and ECP capabilities (if selected in BIOS Setup).

The OmniBook has one parallel port. Its address and properties can be set in the
BIOS Setup utility.

• Connect the parallel printer cable or other parallel cable to the parallel port.

To connect a serial device

The OmniBook’s serial port uses a standard 9-pin serial port. Serial connections
typically are to external modems and fax modems. The OmniBook has one serial
port. Its address can be set in the BIOS Setup utility.

1. Connect the serial cable to the serial port.

2. From the Start menu, click Settings, Control Panel.

3. Double-click Mouse, then click General.

4. Click Change and then select Show All Devices.

5. Under Manufacturers, click Standard Mouse Types.

6. Under Models, change the mouse type to Standard Serial Mouse, then click OK.

4-10

Making Connections

Connecting External Devices

To connect an external keyboard or PS/2 mouse

The 6-pin PS/2 port allows you to attach an external keyboard or a PS/2-compatible
mouse to the OmniBook.

1. From the Start menu, shut down, then restart the OmniBook.

2. Plug the mouse or keyboard PS/2 cable into the PS/2 port on the OmniBook.

• To connect both a mouse and keyboard, use the HP F1469A Y adapter.

• To connect a device that has a PC-type jack, first connect its cable to an

adapter cable with a PS/2 jack.

3. Press the blue power button to turn on the OmniBook.

To connect USB devices

Note

Note

Windows NT 4.0 does not support universal serial bus (USB) devices.

Universal serial bus (USB) provides a bi-directional serial interface for adding
peripheral devices such as game controllers, serial and parallel ports, and scanners
on a single bus. The OmniBook provides one USB port; the OmniBook docking
products provide two USB ports.

• Attach the USB cable to the USB port. Windows 95 automatically recognizes the
USB device. Some USB devices can be connected to the OmniBook in series
with other USB devices—this is called a “daisy-chain” connection.

If you have problems making this connection, contact the vendor of
the peripheral device, as well as the HP website, for the latest versions of the USB
drivers. The USB technology is dynamic and continues to develop.

4-11

Making Connections

Connecting External Devices

To connect a television

Note

At the time of this printing, Windows NT 4.0 does not support a television
connection. Check the HP website at http://www.hp.com/omnibook for updates.

If your television has an S-video port, you can connect it to the OmniBook and use
your television display as a monitor. If you have a newer model television, you can
connect an S-video cable (available at most computer stores), directly between the
television and OmniBook. If your television does not have an S-video port, you’ll

need to order the HP video cable adapter (HP F1459A).

1. From the Start menu, shut down the OmniBook.

2. Connect the S-video cable to the OmniBook.

3. Connect the cable to the S-video port on the back of your television.

4. Turn on the OmniBook.

5. From the Start menu, click Settings, Control Panel, Display.

6. Click the Settings tab, then select TV. (You can select any or all of the choices:
CRT, TV, LCD).

NTSC and PAL Television Standards

If your television uses the PAL standard, you’ll need to change the default BIOS
setting from NTSC to PAL.

1. From the Start menu, shut down, then restart the OmniBook.

2. When you see the HP logo, press F2 to enter the BIOS Setup utility.

3. From the Main menu, select Television Type, then select PAL.

4. Press F10 to save and exit.

To connect audio devices

There is a built-in microphone located just below the OmniBook display. You can
use it to record voice, sound, and music. You can also plug in a stereo input source,
(such as a CD player), an external microphone, external speakers or headphones.

4-12

Making Connections

Connecting External Devices

WARNING

Note

The audio jacks are three-terminal stereo jacks. They are not compatible with
two-terminal mono plugs. Connecting a mono plug into the headphone-out jack
may damage the OmniBook.

• Attach the audio cable to the corresponding audio port.

• When you plug a device into the microphone-in port, the built-in microphone

automatically turns off.

• When you plug a device into the speaker-out port, the built-in speakers
automatically turn off.

4-13

Making Connections

Connecting External Devices

To make an infrared connection

Note

Windows NT 4.0 does not support infrared communication.
By default, the infrared port is not enabled. You must enable it in the BIOS Setup

utility and then install the appropriate infrared driver. For details, refer to the driver’s
Readme file located in \OmniBook\drivers\Win95.

The OmniBook provides two infrared ports—one on the front of the OmniBook
(below the latch) and one on the rear panel. The infrared ports provide wireless,
serial communication between the OmniBook and other IR-equipped devices such
as printers and other OmniBooks.

• Line up the OmniBook’s infrared port and the other infrared port in as straight a
line as possible. The two ports should be no more than 1 meter apart, with no
obstructions in between. Noise from nearby equipment can cause transmission
errors.

• To check the status of communications, go to Infrared Monitor (Start, Settings,
Control Panel).

• To switch between front and rear infrared ports, press Fn+F.

Printing to an Infrared Printer

• Install your printer and assign it to the OmniBook’s IR port. You can then print
from your applications as you would to any other printer. Be sure the OmniBook
and printer infrared ports are properly aligned.

4-14

Making Connections

Connecting External Devices

Transferring Files with an Infrared Connection

To transfer files, you can use the Direct Cable Connection software built into
Windows 95. You need to install it first.

1. From Control Panel, click Add/Remove Programs.

2. Click Windows Setup, Communications, and select Direct Cable Connection.

See the Windows 95 online help for instructions about how to use Direct Cable

Connection.

4-15

Making Connections

Using PC Cards

Using PC Cards

This section describes how to

♦ Insert a PC Card.
♦ Remove a PC Card.
♦ Select a compatible PC Card from a list of tested cards.

To insert a PC Card

Note

Windows NT 4.0 does not support zoomed video. If you are using Windows NT 4.0,

make sure you’ve installed Card Executive (see page 6-18 for instructions).

The OmniBook PC Card slots are available for storing data and expanding the
communication capabilities of the OmniBook. The OmniBook supports standard
Type I, II, and III PC Cards (PCMCIA and CardBus). You can use two Type I or II
cards or one Type III card. Both slots support Zoomed Video, which allows
high-quality multimedia presentations.

Important

1.
writing data. Hold the card with its face up and its connector holes toward the
card slot.

2. Slide the PC Card into the slot until it is flush with the OmniBook.

. Do not remove a PC Card while the OmniBook is actively reading or

4-16

PC Card indicator

Making Connections

Using PC Cards

To remove a PC Card

Do not remove a PC Card while the OmniBook is actively reading or writing data.
Otherwise, you could lose data or the OmniBook could stop responding. When the
card is active, the PC Card indicator appears on the status panel.

1. To remove the card, click the PC Card indicator in the taskbar, then click Stop
(for Windows 95 only). This protects your data and avoids unexpected
problems. You can restart the card by removing it, then inserting again.

2. Press the eject button once to pop the button out.

3. Press the eject button again to eject the PC Card.

4-17

Making Connections

Using PC Cards

List of tested PC Cards

At the time of this printing, the following cards have been tested for use with the
OmniBook.

For the latest information about compatible cards, visit our website at
http://www.hp.com/omnibook and check the Accessories section. Or contact
Hewlett-Packard as described in the Support and Service booklet.

Manufacturer Card Description

3COM XJ-1336 PC Card Modem
3COM 3C589D PC Card 10Mbps LAN
3COM 3C575 PC Card 10/100 CardBus LAN
Xircom CEM56 10/100 Combo 56K PC Card Modem + 10/100 LAN
Xircom CE3 PC Card 10/100 Ethernet LAN
Xircom CM56 56K PC Card Modem

4-18

Making Connections

Using Docking Products

Using Docking Products

A docking product provides external connections for the OmniBook that you can
leave in place whenever you remove the OmniBook from your desk. Instead of
disconnecting and reconnecting peripheral devices, simply undock and dock the
OmniBook. This section describes how to

• Install a docking tray.

• Dock the OmniBook.

• Undock the OmniBook.

For more information about using docking products, see User’s Guide that shipped
with your dock.

To install a docking tray

Your dock requires a tray that accommodates your specific OmniBook model. Install
this tray prior to connecting the OmniBook to the dock.

1. Select the tray labeled for the OmniBook 7100.

2. Slide the rear of the tray into the dock as shown on the dock label.

3. Push down firmly on both sides of the tray until it snaps into place.

To remove a tray from the dock, pull the latch (at the center front of the dock)
towards you until the tray pops free.

4-19

Making Connections

Using Docking Products

To dock the OmniBook

CAUTION

Use only an HP F1454A ac adapter (shipped with OmniBooks compatible with
this dock). Using any other ac adapter could damage the OmniBook and may
void your warranty. Refer to the warranty statement for your product.

1. If you’re using Windows NT, click Start, Shut Down.

2. Plug the power cord into the ac adapter, then into an ac outlet. Plug the ac
adapter into the dock.

3. On the rear of the OmniBook, slide the docking door to the left.

4-20

Making Connections

Using Docking Products

4. Place the OmniBook on the dock platform, with the rear of the computer facing

the dock’s docking connector.

5. Position your fingers on the platform grips as shown below. Use your thumbs to
push the computer into the dock until the computer slides into place.

4-21

Making Connections

Using Docking Products

To undock the OmniBook

1. If you’re using Windows NT, click Start, Shut Down.

2. Press the undock button on the front of the dock and wait for the undock light to
turn green. Then position your thumb as shown and pull the release lever
forward.

3. Remove the OmniBook from the dock.

4-22

5

Expanding the OmniBook

Expanding the OmniBook

This chapter describes some of the optional equipment that can be added to the
OmniBook—components installed inside the computer rather than connected to the

computer’s I/O ports.
This chapter describes procedures to expand or update the capabilities of your

OmniBook, including

♦ Installing a hard disk drive.
♦ Installing a RAM expansion module.

5-2

Installing a Hard Disk Drive

Installing a Hard Disk Drive

This section describes how to

♦ Replace the hard disk drive.
♦ Replace the hard disk drive holder.
♦ Create a hibernate partition for a new hard disk drive.

To replace the hard disk drive

1. Unplug the ac adapter, if present, and remove the battery.

2. Turn the unit bottom side up.

3. Use a screwdriver to pop up the hard drive handle.

4. Pull the tab and remove the hard drive cushion.

5. Slide the hard drive toward the front, then lift it out.

6. Insert the new hard disk drive.

7. Replace the hard drive cushion.

8. Insert the battery.

Expanding the OmniBook

Important

If you are installing a new hard disk drive, you should create a Hibernate partition on
the drive before loading any software—see page 5-5 for instructions.

5-3

Expanding the OmniBook

Installing a Hard Disk Drive

To replace the hard disk drive holder

If you are installing a new hard drive that does not have a plastic holder, you can
remove the holder from the old hard drive.

You’ll need a small Phillips screwdriver for this procedure.

1. Unsnap the two plastic snaps next to the connector and remove the plastic tray.

2. Remove the four screws from the sides of the shield.

3. Remove the hard drive from the shield.

4. Unplug the connector from the hard drive.

5-4

Expanding the OmniBook

Installing a Hard Disk Drive

To create a Hibernate partition

You’ll need the OmniBook, its CD-ROM drive, and the OmniBook Recovery CD to
create a hibernate partition.

1. Connect the ac adapter to the OmniBook.

2. Insert the CD-ROM drive in the OmniBook.

3. Insert the bootable Recovery CD in the CD-ROM drive.

4. Reboot, press ESC twice and select the CD-ROM as the boot device.

5. Reset the OmniBook. The DOS Startup menu appears.

6. Choose option 3:

Create Hibernate Partition (erases Hard Disk).

7. Choose Y to Continue.

8. When prompted for “Hibernate” partition size, we recommend that you create a
288-MB partition, the same as the factory default.

Do not interrupt the Hibernate partition process or unplug the ac adapter until the

process is complete.

5-5

Expanding the OmniBook

Installing a RAM Expansion Module

Installing a RAM Expansion Module

CAUTION

Your OmniBook s computer chips are extremely static-sensitive. Static
electricity can permanently damage computer chips. Handle the RAM module
only by its edges. Before installing the memory module, discharge your body
static electricity by touching the metal shielding around the connectors on the
rear of the OmniBook.

The OmniBook provides an optional memory expansion slot for installing a 3.3-volt
EDO RAM expansion module.

This section describes how to

♦ Install a RAM expansion module.
♦ Remove a RAM expansion module.

s

5-6

Expanding the OmniBook

Installing a RAM Expansion Module

To install a RAM expansion module

Your OmniBook’s computer chips are extremely static-sensitive. Static electricity can
permanently damage computer chips. Before starting, reading the caution on
page 5-6 about how to handle RAM expansion modules.

1. Unplug the ac adapter, if present, and remove the battery.

2. Turn the unit bottom side up and unsnap the RAM cover.

3. Insert the RAM board into the connector at about a 30° angle until it is fully
inserted. Then press down at both sides until both latches snap closed.

4. If only one RAM board is present, you can install it in either connector.

5-7

Expanding the OmniBook

Installing a RAM Expansion Module

To remove a RAM expansion module

Your OmniBook’s computer chips are extremely static-sensitive. Static electricity can
permanently damage computer chips. Before starting, reading the caution on
page 5-6 about how to handle RAM expansion modules.

1. From the Start menu, shut down the OmniBook.

2. Unplug the ac adapter, if present, and remove the battery. (Remove a second
battery if one is installed.)

3. Turn the unit bottom side up and pry open the RAM cover.

4. Release the two metal latches at the sides of the RAM board, so the free edge of
the board pops up.

5. Pull the module out of the connector.

6. Replace the door.

7. Insert the battery.

5-8

6

Using the Recovery CD

Using the Recovery CD

You can use the OmniBook Recovery CD to recover an original OmniBook build, or
you can use it to install the HP custom software over a user-installed alternate
operating system.

The Recovery CD provides the OmniBook-specific drivers to configure your custom
system. The drivers for Windows 95, Windows NT 4.0, and Windows for Workgroups
are located in these places:

• On the Recovery CD ROM, under \Omnibook\Drivers.

• On the OmniBook hard drive under C:\Omnibook\Drivers.

• On the OmniBook website at

http://www.hp.com/omnibook

contains the latest updates of software drivers.

The OmniBook Recovery CD contains the following:

Directory Contains

. This website

README.TXT text file Instructions for using the

RECOVER\

Recovery CD

.

ENC Encoded image of the factory load—either Windows 95 or Windows NT 4.0.
BOOTDISK For creating your own copy of a boot disk (like the

Support Utility

disk).

FILE.CHK Checksum list. Used to verify that software recovery was successful.

OMNIBOOK\

HPUTILS Use this to install the online

and Support files to the \OmniBook directory on your hard drive.

DRIVERS

Use this to manually install individual audio, video, infrared, and PC-Card
(PCMCIA) drivers for Windows NT 4.0, Windows 95, and Windows for
Workgroups. Look for the specific driver for the specific version of your operating
system. Each driver has a README file with instructions.

MANUALS Use this for viewing of the online

installation.

User’s Handbook

User’s Handbook

or to copy the OmniBook Notes

from the CD, not for its

6-2

Using the Recovery CD

Recovering a factory build

Recovering a factory build

If you’ve deleted or lost files on the OmniBook, causing the system to work
improperly, you may need to recover the original factory build.

This section describes how to

♦ Recover the OmniBook factory installation of Windows 95.
♦ Recover the OmniBook factory installation of Windows NT 4.0.

6-3

Hint

Using the Recovery CD

Recovering a factory build

To recover the Windows 95 factory installation

The following procedure describes how to recover the original Windows 95
operating system that came with your OmniBook.

Requirements

♦ OmniBook 7100.
♦ OmniBook 7100 Recovery CD.

This procedure will format the hard disk drive. If possible, back up any files you
would like to save before installing Windows 95.

1. Shut down the OmniBook and insert the CD-ROM drive in the module bay.

2. Connect the ac adapter and turn on the OmniBook.

3. When you see the HP logo, press F2 to enter the BIOS Setup utility.

4. Open the Boot menu and select CD-ROM as the first boot device. (You may want
to change the boot order back to Diskette Drive after completing this procedure.)

5. Insert the Recovery CD into the CD-ROM drive.

6. Press F10, then press Yes to save and exit the BIOS Setup utility.

7. When the menu appears, choose “Recover Windows 95.”

8. When prompted, select Y to erase the hard disk and continue.

9. When prompted, select a file system (FAT16 or FAT32).

The default file system is FAT32. After the hard drive is erased and partitioned,

the OmniBook reboots and begins copying files from the Recovery CD.

The recovery process can take up to an hour. Do not interrupt the recovery

process or unplug the ac adapter until recovery is completed.

6-4

Hint

Using the Recovery CD

Recovering a factory build

To recover the Windows NT factory installation

The following procedure describes how to use the Recovery CD to recover the
original Windows NT 4.0 factory-installation that came with your OmniBook.

Requirements

♦ OmniBook 7100.
♦ OmniBook 7100 Recovery CD.

This procedure will format the hard disk drive. Back up any files you would like to
save before installing Windows NT 4.0.

1. Shut down the OmniBook and insert the CD-ROM drive in the module bay.

2. Connect the ac adapter and turn on the OmniBook.

3. When you see the HP logo, press F2 to enter the BIOS Setup utility.

4. Open the Boot menu and select CD-ROM as the first boot device. (You may want
to change the boot order back to Diskette Drive after completing this procedure.)

5. Insert the Recovery CD into the CD-ROM drive.

6. Press F10, then press Yes to save and exit the BIOS Setup utility.

7. When the menu appears, choose “Recover Windows NT.”

8. When prompted, select Y to erase the hard disk and continue.

After the hard drive is erased and partitioned, the OmniBook reboots and begins

copying files from the Recovery CD.

The recovery process can take up to an hour. Do not interrupt the recovery

process or unplug the ac adapter until recovery is completed.

6-5

Using the Recovery CD

Installing Retail Windows 95

Installing Retail Windows 95

If you install a retail version of Windows 95, you’ll also need to manually install
video, audio, touch pad, PC Card, and infrared drivers.

This section describes how to

♦ Install a retail version of Windows 95.
♦ Install video support for retail Windows 95.
♦ Install audio support for retail Windows 95.
♦ Install PC Card support for retail Windows 95.
♦ Install infrared support for retail Windows 95.

To install a retail version of Windows 95

Requirements

♦ Windows 95 CD-ROM.
♦ OmniBook 7100 drivers for Windows 95

Location: OmniBook hard drive and on the Recovery CD in
\Omnibook\Drivers\Win95.

1. Shut down the OmniBook

2. Insert the CD-ROM / floppy disk drive in the module bay.

3. Connect the ac adapter and turn on the OmniBook.

4. When you see the HP logo, press F2 to enter the BIOS Setup utility.

5. Open the Boot menu and select CD-ROM as the first boot device. (You may want
to change the boot order back to Diskette Drive after completing this procedure.)

6. Insert the Recovery CD into the CD-ROM drive.

7. From the Windows 95 Startup menu, select Create Hibernation Partition and
select ‘Y’ to options.

8. From the A:, type FDISK.

9. Do not enable large disk support. Press Enter to continue.

6-6

Using the Recovery CD

Installing Retail Windows 95

10. Create the Primary and Extended DOS partitions. You will need at least 300 MB
for the Primary Partition.

11. Make the C: an active partition.

12. Choose Exit to MS-DOS from the Windows 95 Startup Menu.

13. From the A: prompt, type Format C:, then type SYS C:.

14. Create a C:\Windows\Options\Cabs directory by typing the following:
Mkdir C:\Windows
Mkdir C:\Windows\Options
Mkdir C:\Windows\Options\Cabs

15. Insert the Windows 95 CD into the CD-ROM drive.

16. Copy the Windows 95 installation files to your hard drive by typing:
C:
Copy G:\Win95\*.* C:\Windows\Options\Cabs

17. Restart the OmniBook, the begin the installation by typing:
C:\Windows\Options\Cabs\Setup

18. Press Enter to begin a routine check of the system.

19. When the following error appears, press the ESC key to continue.

This version of Microsoft Scandisk will work only with MS-DOS version 5.0 and

later. Setup found a compressed volume or a disk-cache utility on your
computer. Quit setup and check your compressed volume with your disk
compression software or remove the disk cache utility. Then run setup again or
choose Esc to continue with setup.

20. Click Yes to accept the license

21. When prompted, select Other Directory and click Next. Enter C:\Windows
the path, click Next, and then click Yes to continue with the specified directory.

22. Choose Portable on the Setup Options screen, then click Next.

23. Enter the appropriate User Information, then click Next.

24. Enter the Product Identification Number, then click Next. The Product
Identification Number is located on the Certificate of Authenticity that you
received with your retail version of Windows 95.

25. Do not detect any Network, Sound, MIDI, or Video Capture Card devices, then
click Next.

26. Follow the prompts until the end of the installation, and then reboot.

for

6-7

Using the Recovery CD

Installing Retail Windows 95

27. Copy the files in D:\Omnibook from the OmniBook 7100 Recovery CD to
C:\Omnibook.

To install video support for retail Windows 95

If you’ve installed a retail version of Windows 95, you’ll need to install video support.
The driver is located on the Recovery CD in \Omnibook\Drivers\Win95\Video.

1. From Control Panel, double-click Display, then click Settings.

2. Click Change Display Type.

3. Under Adapter Type, click Change.

4. Click Have Disk.

5. Enter the directory of the video drivers, then click OK. You may need to specify
the Disk1 directory.

6. Click OK to select ATI Rage LT Pro. If prompted for the second disk, specify the
Disk 2 directory.

7. Under Monitor Type, click Change.

8. Choose Laptop Display Panel (1024x768), then click OK.

9. Click Close, and then Close again. Click Yes to restart the computer.

10. After reboot, re-enter the Display Properties window and click Settings.

11. Set the Desktop Area to 1024 by 768.

12. Choose True Color if desired.

13. Click Close in Display Properties, then click Yes to restart the computer now.

6-8

Using the Recovery CD

Installing Retail Windows 95

To install audio support for retail Windows 95

If you’ve installed a retail version of Windows 95, you’ll need to install audio support.
This driver is located on the OmniBook’s hard drive or on the Recovery CD in
\Omnibook\Drivers\Win95\Audio.

1. From Control Panel, double-click Systems, then click Device Manager.

2. Open the MS Windows Sound System Compatible device under Sound, Video,
and Game Controllers, and confirm the following resources in the Resource tab:

Direct Memory Access 01
Direct Memory Access 00
Interrupt Request 05
Input/Output Range 0530-0537
Input/Output Range 0388-038B
Input/Output Range 0220-022F

3. Click Driver, then click Change Driver.

4. Click Have Disk.

5. Enter the directory of the audio drivers and click OK.

6. Click OK to accept Crystal PnP Audio System CODEC.

7. Click OK to close the Unknown Device Properties window.

8. When prompted to shut down, click No.

9. Open the Unknown device under Other devices.

10. Click on the Driver tab, then click Change Driver.

11. Select Other detected devices then click OK.

12. Click OK to accept Crystal PnP Audio System Control Registers.

13. Click OK to close the Unknown Device Properties window.

14. Click Yes to shut down and restart Windows 95.

6-9

Using the Recovery CD

Installing Retail Windows 95

To install PC Card support for retail Windows 95

If you’ve installed a retail version of Windows 95, you’ll need to install PC Card
support.

1. From Control Panel, double-click System.

2. Click Device Manager.

3. Under PCMCIA Socket, double-click on the device with the red X.

4. Under General, Properties, check Device Usage to enable this device in the
current profile called Original Configuration (Current).

5. Click OK.

6. The PCMCIA Installation Wizard starts.

7. Follow the on-screen instructions.

To install infrared support for retail Windows 95

If you’ve installed a retail version of Windows 95, you’ll need to install infrared
support. This drivers are located on the OmniBook’s hard drive or on the Recovery
CD in \Omnibook\Drivers\Win95\Irda and in \Omnibook\Drivers\Win95\Fastir.

1. Go to the infrared drivers directory (\Omnibook\Drivers\Win95\Irda) and copy
the .INF files to C:\Windows\Inf:

2. If prompted to overwrite old files, click Yes.

3. Reboot the OmniBook.

4. When you see the HP logo, press F2 to enter the BIOS Setup utility.

5. Go to the System Devices menu.

6. Set the Infrared Port to Enabled.

7. Set the Mode to FIR.

8. Set the Base I/O address to either 2F8 IRQ3 or 3F8 IRQ4

9. If necessary, set the DMA Channel to DMA 3.

10. Disable the Parallel Port.

6-10