HP DesignJet 2800cp User Manual
DesignJet 2800CP
© 2004 Hewlett-Packard 1
HP Parts Reference Guide™
www.hp.com/go/hpparts
Carriage Drive Parts
Belt
1
C4704-60207 Carriage (Y-axis) belt - Drives the carriage assembly
Bracket
2
C4704-00005 Y-axis motor bracket - Includes edge wire saddle - Holds Y-Axis Motor
Bushing
3
C4704-40084 Rear slider rod bushing (Spring loaded)
Cable
4
C4704-60015 Carriage board trailing cable with ferrite - Three ribbon cables bundled together - 1.9m (6.3ft) long
Carriage Kit
5
C4723-69096 Carriage assembly - Includes carriage assembly, line sensor, encoder, rear bushing, calibration pen, digitizing sight,
guages - Trailing cable and cable clamp not included
REQUIRES RETURN OF DEFECTIVE PART
C4723-60096 New Part for C4723-69096
Clamp
6
C4704-40085 Trailing cable clamp - Secures the trailing cable to the carriage assembly
Cover
7
C4704-40080 Encoder strip roof
8
C4704-60117 Line sensor lens cover
Ferrite Assembly
9
9170-1687 Ferrite core - Installed on Y-AXIS motor cable
Ground Strap
10
C4704-00016 Encoder ground strap - Provides ground to end of encoder strip
11
C4704-00035 Ground strap - Attached to Y-AXIS bracket
Motor
12
C4723-60277 Carriage (Y-Axis) motor assembly - Drives carriage belt - Includes motor, motor holder, and cable
Pulley
13
C4704-60020 Idler pulley - For carriage (Y-axis) belt - On right end of plotter
Saddle
14
0460-2536 Edge wire saddle for Y-axis bracket
Sensor
C4723-60096 Line sensor - Detects paper width and skew - Measures calibration accuracy and printhead alignment
Spring
16
C1633-80014 Compression spring - For the rear bushing on the carriage
17
C4699-00016 Encoder spring
Strip
18
C4704-60224 Encoder strip - Used to determine carriage position
Tensioner
19
C4723-60063 Y-axis tensioner assembly - Applies tension to carriage belt - Includes wedge, tensioner spring, and housing
Electronic Accessories
Cable (Interface)
5063-1256 IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 2.0m
(6.6ft) long
5063-1257 IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 3.0m
(9.8ft) long
92215S RS-422 serial cable - 8 pin (M) to 8 pin (M) - 2.0m (6.6ft) long - For connecting Apple Macintosh with LocalTalk/serial
connector
DesignJet 2800CP
© 2004 Hewlett-Packard 2
HP Parts Reference Guide™
www.hp.com/go/hpparts
Electronic Accessories
Cable (Interface)
C2950A IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 2.0m
(6.6ft) long
5063-1256 New Part for C2950A
C2951A IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 3.0m
(9.8ft) long
C2990A IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) (type A) to 36 pin (M) Centronics (type B) - 1.8m (6ft) long
NO LONGER SUPPLIED
C2991A IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) (type A) to 36 pin (M) Centronics (type B) - 3.0m (10ft) long
NO LONGER SUPPLIED
Memory (Product)
27
C6229A 4MB SIMM memory module - For DesignJet CP printer
NO LONGER SUPPLIED
28
C6230A 8MB SIMM memory module - For DesignJet CP printer
NO LONGER SUPPLIED
29
C6231A 16MB SIMM memory module - For DesignJet 400, 700, CP series printers
NO LONGER SUPPLIED
30
C6232A 32MB SIMM memory module upgrade - For DesignJet 400, 700, CP series printers
Memory (SIMM)
31
1818-6171 4MB EDO (Extended Data Output) DRAM SIMM memory module
32
1818-6172 8MB EDO (Extended Data Output) DRAM SIMM memory module
NO LONGER SUPPLIED
33
C4723-60264 16MB, 60nS EDO (Extended Data Output) DRAM SIMM memory module
Electronics/Power Supply
Cable
34
C4704-60015 Carriage board trailing cable with ferrite - Three ribbon cables bundled together - 1.9m (6.3ft) long
35
C4704-60025 Ribbon cable assembly with ferrite - Has 28 pin (F) connectors - 1.3m (4.1ft) long
Carriage Kit
36
C4723-69096 Carriage assembly - Includes carriage assembly, line sensor, encoder, rear bushing, calibration pen, digitizing sight,
guages - Trailing cable and cable clamp not included
REQUIRES RETURN OF DEFECTIVE PART
C4723-60096 New Part for C4723-69096
Firmware
37
C4723-69294 Firmware SIMM kit (Revision A.04.08) - Mounts in the electronics module - NOTE: this is not a postscript SIMM
REQUIRES RETURN OF DEFECTIVE PART
C4723-60294 New Part for C4723-69294
Front Panel
38
C4704-60255 Front (Control) panel and cable assembly - Includes function buttons and display
Module
39
C4723-69114 Electronics module - Includes power supply, fan, and main board
REQUIRES RETURN OF DEFECTIVE PART
C4723-60114 New Part for C4723-69114
Motor
40
C4704-60040 Bail motor
PC Board
41
C4704-60009 Refill interconnect board
DesignJet 2800CP
© 2004 Hewlett-Packard 3
HP Parts Reference Guide™
www.hp.com/go/hpparts
Electronics/Power Supply
Power Cord
8120-0698 Power cord (Black) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (For 220V/240V in the USA and Canada)
8120-1378 Power cord (Jade Gray) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (For 120V in USA, Canada, Latin
America, Korea, Taiwan, Thailand, Spain, Brazil, and Vietnam)
RIP Server
C6084-69001 Raster image processor server assembly - External unit used to improve print speed and provide networking for a
DesignJet large format printer - Not for Japan
C6084-69002 Raster image processor server assembly - External unit used to improve print speed and provide networking for a
DesignJet large format printer - Kanji version for Japan
REQUIRES RETURN OF DEFECTIVE PART
C6084-60002 New Part for C6084-69002
Sensor
46
C4704-60029 Right end cover and window closed sensors - Includes cable and connector
47
C4704-60052 Pincharm sensor
48
C4704-60058 Left end cover sensor - Includes cable and connector
49
C4704-60195 Media sensor assembly - Includes, edge measuring and secondary levers, media sensor and holder
C4723-60096 Line sensor - Detects paper width and skew - Measures calibration accuracy and printhead alignment
Switch
51
C4704-60056 Power switch - Includes cable
52
C4704-60261 Stand-by switch asembly
External Case Parts
Bin
53
C4704-60073 Media bin arm (Loop assembly)
C4713-60147 New Part for C4704-60073
Cover
54
C4704-00004 MIO (Modular input/output) cover
55
C4704-00021 Top cover
56
C4704-00033 SIMM slot cover
57
C4704-40057 Electronics module left cover
58
C4704-40058 Electronics module right cover
59
C4704-60274 Electronics module cover
60
C4723-60115 Right end cover - Has cut outs for the control panel
61
C4723-60116 Left end cover
Cross-Brace
62
C4704-60077 Cross-brace (E-size) - Main structure that extends between stand legs
Foot
63
C4704-60086 Foot assembly (includes casters)
Hardware Kit
64
C4704-60095 Hardware kit for printer stand - Includes screwdriver, screws, washers, and media bin retaining clips
Holder
65
C4704-60218 Quick reference holder pocket - Holds quick reference guides and media knife
Leg
66
C4704-60075 Leg assembly - Side support for the plotter - Does NOT include the foot assembly
DesignJet 2800CP
© 2004 Hewlett-Packard 4
HP Parts Reference Guide™
www.hp.com/go/hpparts
External Case Parts
Overlay
C4704-60101 Front panel overlay - Shows the function of the front panel buttons and indicator lights (English)
C4704-60102 Front panel overlay - Shows the function of the front panel buttons and indicator lights (Korean)
C4704-60103 Front panel overlay - Shows the function of the front panel buttons and indicator lights (Taiwanese)
C4704-60104 Front panel overlay - Shows the function of the front panel buttons and indicator lights (German)
C4704-60105 Front panel overlay - Shows the function of the front panel buttons and indicator lights (French)
C4704-60106 Front panel overlay - Shows the function of the front panel buttons and indicator lights (Spanish)
C4704-60107 Front panel overlay - Shows the function of the front panel buttons and indicator lights (Italian)
C4704-60108 Front panel overlay - Shows the function of the front panel buttons and indicator lights (Japanese)
C4704-60109 Front panel overlay - Shows the function of the front panel buttons and indicator lights (Portuguese)
C4704-60110 Front panel overlay - Shows the function of the front panel buttons and indicator lights (Chinese)
Sensor
77
C4723-69071 Take-up reel sensor assembly
REQUIRES RETURN OF DEFECTIVE PART
C4723-60071 New Part for C4723-69071
Spindle
78
C6246-60010 36-inch take-up reel spindle assembly
Strip
79
C4704-40070 Capping strips ( E-size) - Two strips that snap together on the ends of the bin arms
Support
80
C4714-60147 Media bin support (E-size) - Supports media bin arms
81
C4723-60072 Take-up reel left hand support assembly
82
C6246-60009 Take-up reel right hand support assembly
Take-Up Reel
83
C6246A Take-up reel kit for DesignJet 2000CP/2500CP - Includes take-up reel spindle assembly, left and right take-up reel
supports, take-up reel sensor assembly, empty core tubes, and media weight tubes
Tray
84
C4704-60084 Plotter stand tray assembly - Mounted between the feet of plotter
Tube Kit
85
C6246-60011 Media weight and core kit for the take-up reel
Window
86
C4704-60087 Lift-up viewing window
Optional Interfaces
Interface (Product)
J2552B LAN & LocalTalk interface - Has EtherTwist (10Base-T) , ThinLAN (10Base-2) , and LocalTalk (DIN-8) connectors
NO LONGER SUPPLIED
J2555B Token ring LAN interface board - DB-9 and RJ-45 connectors
NO LONGER SUPPLIED
J2590A External JetDirect LAN interface module with RJ-45 connector for EtherTwist (10Base-T) or 100VG/802.12 input and 3
parallel (DB-25) output connectors
NO LONGER SUPPLIED
J2591A External JetDirect LAN interface module and power module - Has EtherTwist (10Base-T) and ThinLAN (10Base-2)
connectors
NO LONGER SUPPLIED
J3264A External JetDirect 500X token ring interface module - Interfaces up to 3 parallel printers to a token ring (DB-9 or RJ-45)
LAN
J3265A External JetDirect 500X LAN interface module - Interfaces up to 3 parallel printers to an ethernet 10Base-T (RJ-45),
10Base2 (BNC), or 100Base-TX (RJ-45) LAN
DesignJet 2800CP
© 2004 Hewlett-Packard 5
HP Parts Reference Guide™
www.hp.com/go/hpparts
Optional Interfaces
Module
J2590-69001 External JetDirect LAN interface module with RJ-45 connector for ethertwist (10Base-T) or 100VG/802.12 input and 3
parallel (DB-25) output connectors
REQUIRES RETURN OF DEFECTIVE PART
J2590-61011 New Part for J2590-69001
J2591-69001 External JetDirect LAN interface module with ethertwist (10Base-T) and ThinLAN (10BASE-2) connectors
J2593-69001 External JetDirect LAN interface module with Ethertwist (10Base-T) and ThinLAN (10BASE-2) input connectors and 3
parallel (DB-25) output connectors - (part of J2593A)
J2594-69001 External JetDirect token ring interface module with DB-9 and RJ-45 input connectors and 3 parallel (DB-25) output
connectors - (part of J2594A)
REQUIRES RETURN OF DEFECTIVE PART
J2594-61011 New Part for J2594-69001
PC Board (Interface)
J2552-69013 LAN and LocalTalk interface - EtherTwist (10Base-T), ThinLAN (10Base-2), and LocalTalk (DIN-8) connectors
J2555-69013 Token ring LAN interface board - DB-9 and RJ-45 connectors
Other Accessories
CD-ROM (Support)
C7769-90066 DesignJet support CD ROM - Version A.04.01 - Has product information, user's manuals, service manuals, diagnostic
software, test drawings, newsletters, and service notes
Cleaning Supplies
C6247A DesignJet cleaning kit - Includes cleaning solution and 20 cleaning rags
Humidor
C6236A DesignJet CP ink system storage container - Holds printheads and printhead cleaners when not in use
Ink System Return Kt
5183-5283 Return kit (Box and instructions) - For returning defective large format printer ink systems covered under CREW
program
Ink and Printhead
C1806A Black ink system - Includes print head, print head cleaner and ink cartridge
C1807A Cyan ink system - Includes print head, print head cleaner and ink cartridge
C1808A Magenta ink system - Includes print head, print head cleaner and ink cartridge
C1809A Yellow ink system - Includes print head, print head cleaner and ink cartridge
C1892A Black UV ink system - Includes print head, print head cleaner and ink cartridge
C1893A Cyan UV ink system - Includes print head, print head cleaner and ink cartridge
C1894A Magenta UV ink system - Includes print head, print head cleaner and ink cartridge
C1895A Yellow UV ink system - Includes print head, print head cleaner and ink cartridge
Kit
C4723-60141 Preventive maintenance kit - Contains line sensor cover, encoder strip, Y-AXIS pulley, belt, motor, cutter, silicon grease,
plastic surface cleaner, synthetic oil and wipes
C4723-60238 Adjustment kit - Includes instructions, empty cartridge, digitizing sight (magnifier) and gauge
Lubricant
6040-0855 Synthetic oil - 4oz (113g) plastic bottle
Manual
5959-9733 HP-GL/2 & HP RTL reference guide - Programming information, handbook for developers
5959-9734 Comparison guide for HP-GL/2 and RTL peripherals (English)
DesignJet 2800CP
© 2004 Hewlett-Packard 6
HP Parts Reference Guide™
www.hp.com/go/hpparts
Other Accessories
Manual Kit
C4703-60041 DesignJet 2000CP/2800CP manual kit - Includes user's guide, setup guide, quick reference guide, and assembly
instructions (English)
C4703-60042 DesignJet 2000CP/2800CP manual kit - Includes user's guide, setup guide, and assembly instructions (Korean)
C4703-60043 DesignJet 2000CP/2800CP manual kit - Includes user's guide, setup guide, and assembly instructions (Traditional
Chinese)
C4703-60049 DesignJet 2000CP/2800CP manual kit - Includes user's guide, setup guide, and assembly instructions (Portuguese)
C4703-60050 DesignJet 2000CP/2800CP manual kit - Includes user's guide, setup guide, and assembly instructions (Simplified
Chinese)
C4704-60304 DesignJet 2000CP/2500CP/2800CP manual kit - Includes user's guide, setup guide, and assembly instructions
(German)
C4704-60305 DesignJet 2000CP/2500CP/2800CP manual kit - Includes user's guide, setup guide, and assembly instructions (French)
C4704-60306 DesignJet 2000CP/2500CP/2800CP manual kit - Includes user's guide, setup guide, and assembly instructions
(Spanish)
C4704-60307 DesignJet 2000CP/2500CP/2800CP manual kit - Includes user's guide, setup guide, and assembly instructions (Italian)
C4704-60338 DesignJet 2000CP/2500CP/2800CP manual kit - Includes user's guide, setup guide, and assembly instructions
(Japanese)
Software
C6072-60281 Toolbox and driver software - HP-GL/2 and RTL drivers for Windows 3.1/95/98/NT 4.0 (all DesignJets), and toolbox
software for Windows 95/NT 4.0 (Only for DesignJet 430/450C/455CA/1050C/1055CM) - On 3.5-inch 1.44MB floppy
disks (English)
C6072-60284 Toolbox and driver software - HP-GL/2 and RTL drivers for Windows 3.1/95/98/NT 4.0 (all DesignJets), and toolbox
software for Windows 95/NT 4.0 (Only for DesignJet 430/450C/455CA/1050C/1055CM) - On 3.5-inch 1.44MB floppy
disks (German)
C6072-60285 Toolbox and driver software - HP-GL/2 and RTL drivers for Windows 3.1/95/98/NT 4.0 (all DesignJets), and toolbox
software for Windows 95/NT 4.0 (Only for DesignJet 430/450C/455CA/1050C/1055CM) - On 3.5-inch 1.44MB floppy
disks (French)
C6072-60286 Toolbox and driver software - HP-GL/2 and RTL drivers for Windows 3.1/95/98/NT 4.0 (all DesignJets), and toolbox
software for Windows 95/NT 4.0 (Only for DesignJet 430/450C/455CA/1050C/1055CM) - On 3.5-inch 1.44MB floppy
disks (Spanish)
C6072-60287 Toolbox and driver software - HP-GL/2 and RTL drivers for Windows 3.1/95/98/NT 4.0 (all DesignJets), and toolbox
software for Windows 95/NT 4.0 (Only for DesignJet 430/450C/455CA/1050C/1055CM) - On 3.5-inch 1.44MB floppy
disks (Italian)
C6072-60301 HP-GL/2 driver software for AutoCAD - For DOS and Windows 3.1/95/NT 4.0 - On 3.5-inch 1.44MB floppy disks
(English)
C6072-60304 HP-GL/2 driver software for AutoCAD - For DOS and Windows 3.1/95/NT 4.0 - On 3.5-inch 1.44MB floppy disks
(German)
C6072-60305 HP-GL/2 driver software for AutoCAD - For DOS and Windows 3.1/95/NT 4.0 - On 3.5-inch 1.44MB floppy disks
(French)
C6072-60306 HP-GL/2 driver software for AutoCAD - For DOS and Windows 3.1/95/NT 4.0 - On 3.5-inch 1.44MB floppy disks
(Spanish)
C6072-60307 HP-GL/2 driver software for AutoCAD - For DOS and Windows 3.1/95/NT 4.0 - On 3.5-inch 1.44MB floppy disks (Italian)
C6071-60368 ZEHRaster software for UNIX - Allows TIFF and JPEG printing on DesignJet 700 series, 1000 series, and CP series
(Japanese)
C7779-60040 ZEHRaster software for UNIX - Allows TIFF and JPEG printing on DesignJet 700 series, 1000 series, and CP series
(Chinese)
C7779-60041 ZEHRaster software for UNIX - Allows TIFF and JPEG printing on DesignJet 700 series, 1000 series, and CP series
(English)
C7779-60042 ZEHRaster software for UNIX - Allows TIFF and JPEG printing on DesignJet 700 series, 1000 series, and CP series
(Korean)
C7779-60043 ZEHRaster software for UNIX - Allows TIFF and JPEG printing on DesignJet 700 series, 1000 series, and CP series
(Taiwanese)
DesignJet 2800CP
© 2004 Hewlett-Packard 7
HP Parts Reference Guide™
www.hp.com/go/hpparts
Other Accessories
Software
C7779-60044 ZEHRaster software for UNIX - Allows TIFF and JPEG printing on DesignJet 700 series, 1000 series, and CP series
(German)
C7779-60045 ZEHRaster software for UNIX - Allows TIFF and JPEG printing on DesignJet 700 series, 1000 series, and CP series
(French)
C7779-60046 ZEHRaster software for UNIX - Allows TIFF and JPEG printing on DesignJet 700 series, 1000 series, and CP series
(Spanish)
C7779-60047 ZEHRaster software for UNIX - Allows TIFF and JPEG printing on DesignJet 700 series, 1000 series, and CP series
(Italian)
Take-Up Reel
145
C6246A Take-up reel kit for DesignJet 2000CP/2500CP - Includes take-up reel spindle assembly, left and right take-up reel
supports, take-up reel sensor assembly, empty core tubes, and media weight tubes
Other Internal Parts
Bushing
146
C3195-40076 Cutter bushing - Connects cutter assembly to slider rod
Cable
147
C4704-60024 Ribbon cable assembly - Has 28 pin (F) connectors - 23.5cm (9.3 inches) long
Clamp
148
C4723-40086 Trailing cable holder
Cutter
149
C4704-60299 Cutter assembly - Auto cutter for rollfeed paper - Only for serial prefix ESA and ESB
150
C4723-60244 Cutter assembly - Auto cutter for rollfeed paper
Elevator
151
C4704-60033 Elevator platform assembly - Raises and lowers ink cartridges to fill the print heads - Located on left side of plotter
Enclosure
152
C4704-60067 Cutter enclosure - Mounted above entry platen
Flag
153
C4704-40007 Service station flag - Spring loaded flag on right side of service station
Refill Assembly
154
C4723-60249 Refill assembly - Mounted inside the left hand cover - Includes motor and gears
Service Station
155
C4723-60276 Service station assembly
Spring
156
C4704-80009 Service station spring
Trim
157
C4704-60113 Right trim assembly - At right of entry platen
158
C4723-60111 Left trim assembly - At left of entry platen
Paper Drive Parts
Bail
192
C4704-60329 Bail assembly - Mounting strip assembly for the starwheel mount assemblies (Not included) - Extends width of plotter
Bearing
193
1410-0708 Sleeve bearing - Used on left end of overdrive assembly
Bushing
194
C1633-40082 Pincharm spring retaining bushing
DesignJet 2800CP
© 2004 Hewlett-Packard 8
HP Parts Reference Guide™
www.hp.com/go/hpparts
Paper Drive Parts
Cam
195
C3180-40020 Pinch arm cam - Attached to pinch arm (Media) lever
196
C3190-60149 Left cam journal - Mounted on left end of pincharm shaft
Gear
197
C1633-40019 Overdrive gear cluster
Gear Assembly
198
C4705-60089 Clutch / overdrive gear assembly
Guard
199
C4704-60295 Starguard starwheel cover assembly
Lever
200
C4704-40059 Pinch arm (media) lever - Used when loading paper
Link
201
C4704-00025 Front wire link
Motor
202
C4704-60040 Bail motor
203
C4723-60303 X-AXIS motor assembly - Includes motor, belt, and worm gear - No longer supplied - Order X-AXIS motor assembly kit
NO LONGER SUPPLIED
C4724-60053 New Part for C4723-60303
204
C4724-60053 X-Axis motor assembly kit - New design does not use a belt - Kit includes motor with attached worm gear, helical gear,
motor mount, screws and nuts for mounting the parts, grease for the helical gear, installation instructions
Mount
205
C1633-40089 Overdrive mount block
Overdrive Assy
206
C4704-60213 Overdrive assembly - Includes overdrive shims, clutch and overdrive gear
207
C4704-60281 Overdrive assembly (B) - Includes overdrive shims, clutch and overdrive gear
Pincharm
208
C4723-60247 Pincharm Assembly - Curved black plastic plate with 4 small rubber rollers (Does NOT include spring or bushing)
Platen
209
C4704-60294 Entry Platen Assembly - Cover/guide that is next to the paper drive (Platen) roller
Roller
210
C4700-60042 Paper drive (Platen) roller assembly - Long gear driven roller - Includes roller and mark encoder
Sensor
211
C4704-60052 Pincharm sensor
212
C4704-60195 Media sensor assembly - Includes, edge measuring and secondary levers, media sensor and holder
Shaft
213
C2848-60032 Pincharm shaft assembly - Includes cam journals mounted on each end
Spring
214
C1633-80005 Compression spring between pincharm assembly and bushing
Starwheel Mount
215
C4704-60143 Big starwheel mount assembly - Includes cover, body, spring and two starwheels
216
C4713-60035 Starwheel mount assembly - Includes cover, body, spring and two starwheels
Support
217
C4704-40026 Roller support bracket on left side plate
DesignJet 2800CP
© 2004 Hewlett-Packard 9
HP Parts Reference Guide™
www.hp.com/go/hpparts
Paper and Other Media
Canvas
C6771A Studio canvas (368 gsm) - 91.4cm (36in) x 10.7m (35ft) roll - For regular ink or UV resistant ink
C7966A Canvas with Matte finish - 61cm (24in) x 10.7m (35ft) (USA)
C7967A Canvas with Matte finish - 91.4cm (36in) x 10.7m (35ft) (USA)
Film (Glossy)
C6794A Durable Imaging Glossy UV media - For UV ink only - 91.4cm (36in) x 30.5m (100ft) roll
Film (Opaque)
C7955A Opaque White Glossy Polyester Film - 61cm (24in) x 15.2m (50ft) (USA)
C7956A Opaque White Glossy Film - 91.4cm (36in) x 15.2m (50ft) (USA)
Paper
C7923A Basic Heavyweight Paper - 61cm (24in) x 30.5m (100ft) (USA and Asia/Pacific)
C7924A Basic Heavyweight Paper - 91.4cm (36in) x 30.5m (100ft) (USA and Asia/Pacific)
Q1739A Heat Transfer Paper - 91.4cm (36in) x 30.5m (100ft) (USA)
Q1745A Paper Backed Fabric Polyester - 91.4cm (36in) x 10.1m (33ft) (USA)
Paper (Backlit)
C7960A Backlit Reverse Print paper - 91.4cm (36in) x 22.9m (75ft) (USA)
C6778A Colorlucent backlit UV paper - 91.4cm (36in) x 30.5m (100ft) roll - For UV (pigmented) inks ONLY
Paper (Banner)
C6786A Banner paper with Tyvek (140 gsm) - UV ink only - 61cm (24in) x 15.2m (50ft) roll
NO LONGER SUPPLIED
C6787A Banner paper with Tyvek (140 gsm) - UV ink only - 91.4cm (36in) x 15.2m (50ft) roll
Paper (Coated)
C6019B Coated paper (98 gsm) - 61cm (24in) x 45.7m (150ft) roll (USA, Canada, and Latin America)
C6021B Heavyweight coated paper - 61cm (24in) x 30.5m (100ft) roll (USA, Canada, and Latin America)
NO LONGER SUPPLIED
C6029C Heavyweight coated paper - 61cm (24in) x 30.5m (100ft) roll - For regular or UV resistant ink
C6020B Coated paper (98 gsm) - 91.4cm (36in) x 45.7m (150ft) roll (USA, Canada, and Latin America)
C6022B Heavyweight coated paper - 91.4cm (36in) x 30.5m (100ft) roll (USA, Canada, and Latin America)
NO LONGER SUPPLIED
C6030C Heavyweight coated paper - 91.4cm (36in) x 30.5m (100ft) roll - For regular or UV resistant ink
Paper (Glossy)
C8315A High Gloss Photo Paper - 61cm (24in) x 30.5m (100ft) (USA and Asia/Pacific)
C8316A High Gloss Photo Paper - 91.4cm (36in) x 30.5m (100ft) (USA and Asia/Pacific)
C6025A High gloss photo paper - 61cm (24in) x 30.5m (100ft) roll (USA, Canada, and Latin America)
C6026A High gloss photo paper - 91.4cm (36in) x 30.5m (100ft) roll (USA, Canada, and Latin America)
Paper (Photo)
C8310A Basic Photo Satin paper - 61cm (24in) x 30.5m (100ft) (USA and Asia/Pacific)
C8311A Basic Photo Satin paper - 91.4cm (36in) x 30.5m (100ft) (USA and Asia/Pacific)
Paper (Poster)
C7949A Outdoor Billboard Paper - Blue back - 91.4cm (36in) x 30.5m (100ft) (USA)
Paper (Satin)
C7952A Proofing Paper RC Satin - 91.4cm (36in) x 30.5m (100ft) (USA)
Paper (Semi-Glossy)
C6023A Semi-gloss photo paper - 61cm (24in) x 30.5m (100ft) roll (USA, Canada, and Latin America)
C6782A Paper based semi-gloss media - 61cm (24in) x 30.5m (100ft) roll
NO LONGER SUPPLIED
Loading...