Model No: AXM204UK
Micro System with docking for iPod/iPhone
iPod and iPhone are trademark of Apple Inc.,
registered in the U.S. and other countries.
“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect
specifially to iPod or iPhone respectively, and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this device or its compliance with
safety and regulatory standards.
SOME DOS AND DON'TS ON THE SAFE USE OF EQUIPMENT
This equipment has been designed and manufactured to meet international safety standards
but, like any electrical equipment, care must be taken if you are to obtain the best results and
safety is to be assured.
***************
DO
read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and
inter-connections between the pieces of equipment) are properly made and in
accordance with the manufacturer's instructions. Switch off and withdraw the mains
plug before making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation
or safety
of your equipment.
DO be careful with glass panels or doors on equipment.
DO route the mains lead so that it is not likely to be walked on, crushed, chafed, or
subjected to excessive wear and tear or heat.
***************
DON'T remove any fixed cover as this may expose dangerous voltages.
DON'T obstruct the ventilation openings of the equipment with items such as newspapers,
tablecloths,
curtains, etc. Overheating will cause damage and shorten the life of the
equipment.
DON'T allow electrical equipment to be exposed to dripping or splashing, or objects filled
with liquids, such as vases, to be
placed on the equipment.
DON'T place hot objects or naked flame sources such as lighted candles or nightlights on,
or close to equipment. High temperatures can melt plastic and lead to fires.
DON'T use makeshift stands and NEVER fix legs with
wood screws - to ensure complete
safety always fit the manufacturer’s approved stand or legs with the fixings provided
according to the instructions.
DON'T use equipment such as personal stereos or radios so that
you are distracted from
the requirements of traffic safety.
DON'T listen to headphones at high volume, as such use can permanently damage your
hearing.
DON'T leave equipment switched on when it is
unattended unless it is specifically stated
that it is designed for unattended operation or has a stand-by mode. Switch off
using the switch on the equipment and make sure that your family knows how to
do
this. Special arrangements may need to be made for infirm or handicapped people.
DON'T continue to operate the equipment if you are in any doubt about it working normally,
or if it is
damaged in any way - switch off, withdraw the mains plug and consult your
dealer.
ABOVE ALL
− NEVER let anyone especially children push anything into holes, slots or any other
opening in the case - this could result in a fatal electric shock;
− NEVER guess or take chances with electrical equipment of any kind
− it is better to be safe than sorry!
***************
UK-1
The above mark is in compliance with the Waste Electrical and Electronic Equipment Directive
2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment including any spent or
discarded batteries as unsorted municipal waste, but use the return and collection systems
available. If the batteries or accumulators included with
this equipment display the chemical
symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than
0.0005% Mercury, or more than 0.002% Cadmium or more than, 0.004% Lead.
UK-2
SAFETY PRECAUTIONS
To achieve the utmost in enjoyment and performance, please read this manual carefully before attempting to
operate the unit in order to became familiar with its features, and assure you years of faithful, trouble free
performance and listening pleasure.
Important Notes
* Keep these instructions: the safety and operating instructions should be retained for future reference.
* Avoid installing the unit in locations described below:
* Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters; on top
of other stereo equipment that radiates too much heat; places lacking ventilation or dusty places;
places subject to constant vibration; humid or moist places.
* Make sure not to obstruct the ventilation holes. Ventilation should not be impeded by covering the
ventilation
* Before turning on the power for the first time, make sure the power cord is properly installed. The
mains plug is used as the disconnect device and it must always remain readily operable. To
completely disconnect the equipment from the mains supply, the mains plug of apparatus must be
disconnected from the mains socket.
* The product must not be exposed to dripping or splashing and no objects filled with liquids, such
as vases, should be
* Keep a minimum distance of 10 cm around the apparatus to allow adequate ventilation.
* Please dispose of spent batteries in an environmentally friendly manner by using a local recycling
scheme.
* Only use this equipment
* No naked flame sources such as lighted candles should be placed on the apparatus.
* Do not expose batteries to excessive heat such as sunshine, fire or the like.
holes with items such as newspapers, table-clothes, curtains etc.
placed on the equipment.
in moderate climates.
For safety reasons, do not remove any covers or attempt to gain access to the
Refer any servicing to qualified personnel.
Do not attempt to remove any screws, or open the casing of the unit; there are no user serviceable parts
inside, refer all servicing to qualified service personnel.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR
USER SERVICEABLE PAR TS INSIDE, REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
DANGEROUS VOLTAGE
There is high voltage within this product's enclosure that may be of sufficient magnitude to
constitute a risk
ATTENTION
The owner's manual contains important operating and maintenance instructions, for your safety,
it is necessary to refer to the manual.
Note:
- This unit will become warm when used for a long period of time. This is normal and does not indicate
a problem with the unit.
Excessive sound pressure from earphones and headphones can cause hearing loss.
-
- If an unusual condition occurs in the display window or with an operating button, switch the unit off and then
on again.
of electric shock.
inside of the product.
BACK), NO
UK-3
CLASS 1 LASER PRODUCT
KLASS 1 LASER APPARAT
LUOKAN 1 LASER LAITE
KLASSE 1 LASER PRODUKT
You can see this carved picture on the
back of the main unit.
LASER SAFETY
This unit employs a laser. Only qualified service personnel should attempt to repair.
CAUTION
CLASS 1 LASER PRODUCT
Operating the unit in a way other than specified herein,or
making adjustments to the unit may result in hazardous
radiation exposure
You can see this
label in the CD
compartment.
WARNING: RISK OF INVISIBLE LASER RADIATION WHEN CD LID IS
OPEN OR INTERLOCKS FALL.AVOID
DIRECT EXPOSURE TO THE
BEAM.
The speaker cloth is a flexible material. The speaker
cloth should not be pushed by hand or object. It is
easy to damage a speaker cone.
UK-4
The unit supports the listed iPod/iPhone devices
The unit supports the listed iPod/iPhone devices
(iPod/iPhone devices shown are not included)
UK-5
Assembly Drawing of Unit and speaker
1. Speakers connection
Max connection distance is 2 metres
3. Universal Dock adapter connection
(iPod adaptors are not included)
FEATURES AND CONTROLS
1
2
3
4
5
78
9
10
11
12
13
1415161718
192021
6
28
27
26
25
24
23
22
UK-6
1. SPEAKER
2. LINE IN JACK
3. FM ANTENNA
4. LCD DISPLAY
5. CD DOOR
6. IR SENSOR
7. USB DEVICE IN PORT
8. SD/MMC MEMORY CARD
IN SLOT
9. PRESET/FOLDER DOWN BUTTON
10. iPod/MEM/C-ADJ. BUTTON
11. BUTTON
OPEN/CLOSE
12. STANDBY/ON BUTTON
13. STANDBY LED INDICATOR
14. FUNCTION BUTTON
15. TIMER BUTTON
16. VOLUME “-” BUTTON
17. VOLUME “+” BUTTON
18.
PRESET/FOLDER UP BUTTON
19. STOP/MENU BUTTON
20. SKIP/TUNE SEARCH UP BUTTON
21. iPod CONNECTOR
AC CORD
22.
23. SPEAKER OUT
24.
HEADPHONES JACK
25.
PLAY/PAUSE/ENTER BUTTON
26. SKIP/TUNE SEARCH DOWN
BUTTON
27. AC POWER MAIN SWITCH
28. HITCHING HOLE
(L & R) JACK
REMOTE CONTROL
1. STANDBY BUTTON
2. iPod/MEM/CLOCK- ADJ. BUTTON
3. SKIP/TUNE SEARCH DOWN BUTTON
4. STOP/MENU BUTTON
5. PRESET/FOLDER DOWN BUTTON
6. REPEAT BUTTON
7. EQ BUTTON
8. MUTE BUTTON
9. VOLUME “-” BUTTON
10. INTRO BUTTON
11. VOLUME “+” BUTTON
12. SLEEP BUTTON
13. TIMER BUTTON
14. PRESET/FOLDER UP BUTTON
15. RANDOM BUTTON
16. SKIP/TUNE SEARCH UP BUTTON
17. ID3/MONO/ST. BUTTON
18. OPEN/CLOSE BUTTON
19. FUNCTION BUTTON
20. PLAY/PAUSE/ENTER BUTTON
PUTTING THE BATTERIES INTO THE REMOTE CONTROL UNIT
1. Slide to open the battery compartment.
2. Place the battery (CR2032) into the battery compartment according
to the polarity marking, with the “+” sign facing up.
3. Replace the battery compartment until it clicks.
Note: Remove the battery from the remote control if not in used for a
long period of time. Do not mix normal batteries with
rechargeable batteries. When the battery becomes weak, the
remote control will not be functioned properly, replace with new
battery if that happened.
181920
1
17
2
3
4
5
6
7
8
16
15
14
13
12
11
9
10
**BATTERY INCLUDED**
LCD DISPLAY WINDOW
A. SLEEP INDICATOR
B. TIMER INDICATOR
C. ALBUM/RADIO MEMORY NUMBER INDICATOR
D. INDICATOR
REPEAT 1 & ALL
E. STEREO INDICATOR
E. VOLUME HIGH/LOW INDICATOR
F. TRACK/NUMBER/TIME INDICATOR
OPERATING THE UNIT
When you first plug the unit into the AC outlet,
rear of the unit.
STANDBY. Turn off the main switch of the unit and pull the AC plug out of the
completely.
POWER/STANDBY
1. Press the STANDBY/ON button on the unit or on the remote control to switch the unit on.
2. Select the sound source (CD, USB, SD CARD, iPod, AUX or TUNER)
corresponding display will light up.
3. Adjust the volume with the VOLUME (+ or -) button on the unit or VOLUME (+ or -) button on the remote control.
4. Press the STANDBY/ON button again to turn off the unit.
Note:
1. If there is no signal under the CD/USB DEVICES/ SD & MMC CARD/ mode, the main unit will be switched off
within 15 minutes automatically.
2. During in the iPod mode, if there is no iPod Player on the iPod deck bracket; the main unit will also turn off within
15 minutes automatically.
3. During in standby mode, press any button/key can make the display light
4. Please turn the main switch off to save energy, when you do not use the unit.
CLOCK SETTING
During
1. Press and hold the iPod/MEM/C-ADJ. button until the time displays will change to 12-hour(or 24-hour) digit and flash.
2. Press the SKIP/TUNE SEARCH(UP or DOWN) button to adjust 12-hour or 24-hour digit.
3. Press the iPod/MEM/C-ADJ. button again, the HOUR digit will
SEARCH (UP or DOWN) button to adjust HOUR digit.
You can press the STANDBY/ON button on the unit or on the remote control to switch the unit ON or
in the STANDBY mode.
the unit will be in standby mode before turn ON the main switch on the
UK-7
A
B
wall socket if you want to switch off
by pressing the FUNCTION button. The
iPod
for 10 seconds.
flash on the display, press the SKIP/TUNE
D
C
E
F
G
4. Press the iPod/MEM/C-ADJ. button once more, the MINUTE digit will flash on the display, press the SKIP/TUNE
SEARCH (UP or DOWN) button to adjust MINUTE digit.
5. Press the iPod/MEM/C-ADJ. button again to confirm the time.
6. Each enable state as
TIMER SETTING
During in the STANDBY OFF/ON mode.
1. After adjusting clock, press the TIMER button for a few seconds, " ON" and "00:00" appears on the display
and the HOUR digit flashes.(F1)
2. Press the SKIP/TUNE SEARCH(UP or DOWN) button to
3. Press the TIMER button again, the MINUTE digit will start flashing, adjust it by pressing the SKIP/TUNE
SEARCH (UP or DOWN) button.
4. Press the TIMER button once more to confirm and order TIMER ON time.
5. After adjusting "TIMER ON",
6. Repeat the above steps 2 to 3, and then press the TIMER button once more to confirm and order TIMER OFF time.
7. Now the "TUNER" appears on the display with flashing, adjust “TUNER,
the SKIP/TUNE SEARCH(UP or DOWN) button.
8. Press the TIMER button again, the timer "VOL" indicator appears on the display and flashes, adjust the timer
volume high or low by pressing the TUNING/SKIP (UP
9. Each enable state as shown above will be cleared if the button is not pushed in 10 seconds.
10. After adjusting "TIMER ON" and "TIMER OFF", press the TIMER button, " " appears on the display.
11. The unit will be switched on
automatically at "TIMER OFF" order.
Note: If the display shows "ERROR" while you set the “TIMER ON”, it means both “TIMER ON” and “TIMER OFF” is
the same. In
EQ CONTROL(on the remote control)
EQ shows the present sound tone. When you press the EQ button , the sound tone changes as below:
TO SET SLEEP FUNCTION(on the remote control)
1. If you want to fall asleep to music, press the SLEEP button .
2. You may select the TUNER, CD/MP3, USB, SD/MMC, iPod or AUX mode in
up to10 minutes of music before shutting itself off automatically.
shown above will be cleared if the key is not pushed in10 seconds.
adjust it.
" OFF" appears on the display and the HOUR digit flashes.(F2)
CD, USB, SD CARD or iPod" by pressing
or DOWN) button.
automatically at "TIMER ON" order and start playing, the unit will be switched off
this case, please go to “TIMER OFF” to set the off time first.
F1 F2
ROCK CLASSIC POP PAS S
JAZZ
sleep function to play from 90, 80, 70
FUNCTION SELECT
The function is that when it presses the button the mode is changed. Display changes as below:
USB
CD
RADIO OPERATION
1. Press the FUNCTION button on the main unit (or remote control) to select the TUNER mode that to select the FM
operation.
2. Select the desired frequency with the SKIP/TUNE
control).
Mono/Stereo Select
This unit can receive the FM mode only.
1. When you want to select FM stereo station, press the ID3/MO./ST. button once on the remote control only.
The "
2. When you press the ID3/MO./ST. button once again, the FM STEREO indicator will turn off & switch to
MONO FM status.
Automatic Tuning
1. Press the SKIP/TUNE SEARCH (UP or DOWN)
will automatically search the first station of sufficient signal strength.
2. Repeat above procedure if you wish to select another station.
Programming preset stations
You can also preset stations of your choice and store up to 30
1. Tune to the required station.
2. Press the iPod/MEM/C-ADJ. button.
3. Press the PRESET/FOLDER(UP or DOWN) button for your desired station number.
4. Press the iPod/MEM/C-ADJ. button again to confirm your selection.
5. To program more stations into memory, repeat the
6. To change the stored preset stations, repeat the above steps 2 to 4.
" indicator will appear on the display that the reception is at its best.
NORMAL
TUNER
IPODSD CARD
AUX
SEARCH(UP or DOWN) button on the main unit (or remote
button for a few seconds, then release the button. The tuner
FM stations in its memory.
above steps 2 to 4.
UK-8
Notes:
1. Storing a new station into a preset location will erase the previously stored station in that location.
2. Power off will not erase the memory of preset stations. Perform the stations presetting procedures again to store
the stations.
3. During the unit in
erase all preset memory.
Selecting the Preset Stations
1. Press the PRESET/FOLDER(UP or DOWN) button to select the desired preset station number.
2. The numeric location of that preset station is displayed along with the
FM Antenna
Extend the FM antenna for better FM reception.
COMPACT DISC
1. Always use a compact discs bearing the mark as shown.
2. Notes on handling discs
Removing the disc from its storage case and loading it.
* Do not touch the reflective recorded surface.
* Do not stick paper
* Do not bend the disc.
3. Storage
* Store the disc in its case.Do not expose discs to direct sunlight or high
temperatures, high humidity or dusty places.
4. Cleaning a
* Should the disc become soiled, wipe off dust, dirt and fingerprints with a soft cloth. The disc should be
cleaned from the center to the edge.
* Never use benzene, thinners, record cleaner fluid or anti
STANDBY mode, press the PRESET/FOLDER UP button and PLAY/PAUSE/ENTER button to
corresponding frequency.
or write anything on the surface.
disc
static spray.
FROM THE CENTRE
TO THE EDGE
CORRECT
* Be sure to close the CD door so the lens is not contaminated by dust.
* Do not touch the lens.
CD/MP3/WMA OPERATION
Listening To Compact Disc (CD/MP3/WMA)
1. Press the FUNCTION button on the unit to select the
2. Press the OPEN/CLOSE button on the main unit , and then the CD door will open automatically.(F3)
3. Insert the CD/MP3 disc into the CD compartment, press the OPEN/CLOSE button again to close the CD door. The
main unit will read the CD/MP3 disc automatically.
NOTE: (1) This unit can play CD, CD-R, CD-RW, MP3 and WMA discs.
(2) It can read " 8 cm " and " Multi Section " MP3 DISC.
(3) The "Playback Transfer Rate" in MP3
transfer bit rate : 8 - 192kbps.
(4) The "Max Readable 99 folders and 999 tracks".
(5) If no disc or can`t read TOC, NO DISC will be displayed.(F4)
Playing The Entire CD/MP3/WMA
- CD
1. Insert the CD disc into the CD compartment, the main unit will automatically read the total number of the folders
and tracks at the same time.
2. Press the PLAY/PAUSE/ENTER button, the unit will play the first track of
3. Press the PLAY/PAUSE/ENTER button once again, the time elapsed indicator will flash.(F6)
4. Press SKIP/TUNE SEARCH(UP or DOWN) button once to change Trac k NO., press and hold the SKIP/TUNE
SEARCH (UP or DOWN) button once to skip fast forward or backward of
5. To resume playback, press the PLAY/PAUSE/ENTER button once more again.
6. To stop playback, press the STOP/MENU button once on the unit (or remote control).
NOTE:To access the key more accurately, please press the corresponding edge of each corner of the round knob.
and WMA. (a). In MP3, transfer bit rate : 8 - 256 kbps. (b). In WMA,
INCORRECT
CD mode.
(or remote control)
F3
UK-9
F4
the CD disc automatically.(F5)
each song.
F5 F6
- MP3/WMA
1. Insert the MP3/WMA disc into the CD compartment, the main unit will automatically read the total number of the
folders and tracks at the same time.
2. Press the PLAY/PAUSE/ENTER button, the unit will play the first track of
3. Press the PLAY/PAUSE/ENTER button once again, the time elapsed indicator will flash.(F8)
4. To change Tr ack NO., Press SKIP/TUNE SEARCH(UP or DOWN) button once. Press and hold the SKIP/TUNE
SEARCH (UP or DOWN) button once to skip fast
5. To resume playback, press the PLAY/PAUSE/ENTER button once more again.
6. To change the ALBUM NO., press the PRESET/FOLDER (UP or DOWN) button once.
7. To stop playback, press the STOP button once on the unit (or remote control).
NOTE:To access the key more accurately, please press the corresponding edge of each corner of the round knob.
forward or backward of each song.
the CD disc automatically.(F7)
F7
F8
Note: If the main unit is not working properly, disconnect the power source and then reconnect it again
ID3 OPERATION (on the remote contr ol)
During in the MP3/WMA mode
1. Press the ID3/MO./ST. button once to open the ID3 function.
2. If the MP3/WMA file is written “ID3”, it will automatically
and “ALBUM NAME” indicated on the display .
3. Press the ID3/MO./ST. button on the remote again. Then the unit will resume to play normally.
USB/SD CARD O PE RAT IO N
During in the STANDBY mode
1. Insert the USB DEVICE or SD/MMC CARD, and then press the STANDBY button on the main unit (or remote
control) to power"ON" the unit.
2. Press the FUNCTION button on the main unit (or remote control) to select the USB
unit will automatically read the total number of the folders and tracks at the same time. (F9)
3. If the USB memory device more than one folder.
a. Press the PRESET/FOLDER (UP or DOWN) button to select each folder.
b. Press the SKIP/TUNE
4. If the MP3 and WMA are written in "ID3".
a. During the unit in the MP3 or WMA playing. Press the ID3/MO./ST. button once. The display will show
a "ID3
"ALBUM NAME" which move from the right corner to the left corner on the display continuously.
b. Press the ID3/MO./ST. button once again. The display will
will play normally.
Note:
2. This unit can support most of USB devices and SD/MMC/SDHC cards. The memory capacity up-to 32GB.
cannot access (or access a longer time) the memory capacity over 32GB. Otherwise, make an others to access it.
3. It can support USB version 1.1 and 2.0.
4.
5. The main unit does not support the WMA file which is protected “DRM FILE”.
Playing The Entire flash disc
1. Playback will start by pressing the PLAY/PAUSE/ENTER button. Playback starts with the first track. The display
shows the current track number and its elapsed time.(F10)
2. To interrupt playback , press the PLAY/PAUSE/ENTER button. The time elapsed indicator will flash.(F11)
3. To resume playback, press the PLAY/PAUSE/ENTER button again.
4. To stop playback, press the STOP/MENU button.
NOTE:To access the key more accurately, please press the corresponding edge of each corner of the round knob.
ON", and then it will automatically search more than 64 letters for "TITLE NAME", "ARTIST NAME" or
1. The main unit can play MP3 and WMA only in this mode.
Not support all kinds of “ dual voltage-MMC” card nor “MMC-Plus” card.
SEARCH(UP or DOWN) button to select current track in desired folder.
search the information of “TITLE NAME”, “ARTIST NAME”
or SD/MMC mode. The main
show a "ID3 OFF", and then the main unit
It
F9
F10
Note : In any time, the USB DEVICE or SD CARD must be fixed well under in the STANDBY mode to avoid the main
unit and USB DEVICE or SD CARD were damaged.
F11
UK-10
REPEAT PLAY(on the remote control)
- CD
1. Press the REPEAT button once , REPEAT is displayed. The main unit will play the current track repeatedly.(F12)
2. Press the REPEAT button twice, REPEAT ALL is displayed. The main unit will play all tracks repeatedly.(F13)
Press the REPEAT button thrice, REPEAT function will be off.
3.
F12
- MP3/WMA
1. Press the REPEAT button once , then REPEAT is displayed. It will play the current track repeatedly.(F14)
2. Press the REPEAT button twice, REPEAT ALL is displayed. It will play all tracks repeatedly.(F15)
3. Press the REPEAT button thrice, then REPEAT ALBUM is
album. (F16)
4. Press the REPEAT button four times, then REPEAT function will be off.
F14
RANDOM PLAY(on the remote control)
1. Press the RANDOM button once , and then RANDOM is displayed.(F17)
2. Press the RANDOM button once again, and then resume to normally play.
INTRO PLAY(on the remote control)
1. Press the INTRO button once, and then INTRO is displayed. The main unit will play
track.(F18)
2. Press the INTRO button twice, and then resume to normal play.
PROGRAM MODE
User can make the program up to 32 tracks in CD mode or 64 tracks in MP3/WMA/USB/SD CARD mode in any
desired order. Program mode is activated while
1. How to play the program
- CD
1) Press the iPod/MEM/C-ADJ. button, shift to PROGRAM mode.(F19)
2) Press the SKIP/TUNER SEARCH(UP or DOWN) button, the track number will be changed.
3) Press the iPod/MEM/C-ADJ. button to confirm the track number.
-
MP3/WMA/USB/SD CARD
1) Press the iPod/MEM/C-ADJ. button, shift to PROGRAM mode. The album number is flashing. (F20)
2) Press the PRESET/FOLDER button, the album number will be changed.
3) Press the iPod/MEM/C-ADJ. button , the track number is flashing.(F21)
4) Press the SKIP/TUNER SEARCH button,
5) Press the iPod/MEM/C-ADJ. button to confirm the track number.
in stop mode.
the track number will be changed.
displayed. It will play repeatedly the current
F15
the first 10 seconds of each
F17
F13
F18
F16
F19
2. PROGRAM PLAY
Press the PLAY/PAUSE/ENTER button on the unit (or remote control), it will be play starting with the first track of the
program. When all tracks have been played, the unit display will show the number of tracks and the playing time of
the CD/MP3/WMA tracks.
3.
CANCEL PROGRAM
1. Press the STOP button once, or open the CD tray door and close it again then the memory will be erased.
2. Set a new program, the existing one will be cleared.
Note : During in the program mode.
1. Press the "REPEAT"
the current track.
2. Press the “REPEAT" button twice, the "REPEAT ALL" will light on the display. Then the main unit will repeat all
the total number
3. Press the “REPEAT” button once more again. The main unit will return to play the program normally.
button once, the "REPEAT" indicator will light on the display. Then the main unit will repeat
of tracks.
F20
F21
UK-11
iPhone
iPod/ OPERATION
During the unit in STANDBY mode:
1. Insert the iPod/iPhone players in the iPod/iPhone dock bracket on the front panel of the main unit fixedly.
2. Power on the main unit, and then press the FUNCTION button to the iPod mode, the iPod indicator will appear on
the main unit display. (F22)
During the unit in iPod/iPhone mode:
1. Press the PLAY/PAUSE/ENTER (only ) button once to start the iPod/iPhone playing. Adjust the volume
control by turning the To stop the current playing, press the STOP/MENU (only in iPod)
button once.
2. Press the PLAY/PAUSE/ENTER (only in iPod) button once to pause the current track.
To resume the playback, press the PLAY/PAUSE/ENTER(only in iPod) button once again.
3. To skip forwards or backwards, press the (UP or DOWN) button to select the desired track.
4. Press the REPEAT
iPod touch version 1.1. or above can support REPEAT or RANDOM function.
Note: 4
During the unit in iPod/iPhone MENU mode:
1. During the unit in iPod/iPhone mode, press the iPod/MEM/C-ADJ. button once, the unit will enter to the iPod/iPhone
MENU mode. The iPod MENU indicator will appear
2. Press the STOP/MENU (only in iPod) button return to the iPod/iPhone menu.
a. To select the current menu as belows :
Music > Extras > Photo Import (without this function display on the iPod Mini) > Settings
Backlight > Now Playing will show on the iPod Player display.
b. Press the (UP or DOWN) button on the unit (or remote control) to search the current
menu.
3. Press the PLAY/PAUSE/ENTER
a. Press the (UP or DOWN) button on the unit (or remote control) to search the current
content in the each desired menu folder.
b. If you want
4. To resume playback, press the iPod/MEM/C-ADJ. button once again, the unit will return to iPod mode.
NOTE:To access the key more accurately, please press the corresponding edge of each corner of the round knob.
Charging the iPod/iPhone Player battery through the main unit:
1. iPod/iPhone Player has a internal nonremovable battery, the battery may need
a while.
2. You can charge the iPod/iPhone Player through the main unit automatically under the STANDBY or POWER ON
mode.
Note : 1. The iPod/iPhone Player battery is 80-percent charged in about an hour, and fully charged
If you charge it while playing music, it may take longer.
2. It is not better to charge under the TUNER mode. It may interfere the reception.
3. In any time, you can control the iPod/iPhone player on the main unit, remote control or iPod/iPhone player itself
while the unit in the "iPod" or "iPod MENU" mode.
4. In any time, the iPod/iPhone player must be
iPod/iPhone player were damaged.
5. During the unit in iPod mode. The video function of the iPod/iPhone with abnormal working normally. Update
the latest version of the iPod/iPhone video function from the apple web-site.
VOLUME (+ or -) button.
or RANDOM button to make the iPod/iPhone playing repeatedly or randomly.
SKIP/TUNE SEARCH
SKIP/TUNE SEARCH
return to the iPod/iPhone menu, press the STOP/MENU (only in iPod) button again.
iPod
in
SKIP/TUNE SEARCH
on the remote control
on the unit display. (F23)
(only in iPod) button enter to the desired menu folder.
to be charged that is not used for
fixed well under in the STANDBY mode to avoid the unit and
>Shuffle Songs >
in about a few hours.
F22
AUX IN PLAY
The AUX input is located of the unit. Use a 3.5mm stereo jack cable to connect audio equipment
through the LINE IN jack.
1. To
select the AUX input function, repeatedly press the FUNCTION button on the unit (or remote control) until the
AUX is indicated on the display.
2. Press the VOLUME (+ or -) button to adjust the sound output level.
Note: LINE in cable not included.
MUTE SETTING(on the remote control)
1. When you press the MUTE button once on the remote control, the volume level will flash and the audio output will be
temporarily terminated.(F24)
2. Press the MUTE button again, the volume level and the audio output will return to normal.
on the left hand side
F23
F24
CLOCK BACKUP
If you want
1. Ensure that the unit connected to the AC mains
2. Ensure that AC power switch turn to “ON”
The memory will be lost if the power is switched-off completely.
to keep its original settings, please do the following:
UK-12
LISTEN TO THE MUSIC BY USING HEADPHONE
Plug your headphones (3.5mm mini-stereo plug) into the headphones jack on the right hand side of the unit. The sound
will be heard through the headphones, not the speaker.
SPECIFICATION
POWER SUPPLY : AC 230V~50Hz
OUTPUT POWER :
POWER CONSUMPTION:
STANDBY POWER CONSUMPTION:
UNIT DIMENSION : 232 (W) x 125 (D) x 186 (H) mm
SPEAKER
N. W. :
RADIO SECTION
FREQUENCY RANGE :
COMPACT DISC SECTION
OPTICAL PICKUP : 3 - BEAM LASER
FREQUENCY RESPONSE :
SPECIFICATION SUBJECT TO CHANGE WITHOUT FURTHER NOTICE.
Ventilation warning : " The normal ventilation of the product shall not be impeded for intended use."
BOX DIMENSION : 120 (W) x 80 (D) x 186 (H) mm
4.5 Watts x 2
2.3kg
FM 87.5-108 MHz
100Hz - 16kHz
23 W
0.65 W
CONTACT D ETAI LS
We trust you are completely satisfied with this product from Argos Ltd, however please feel free to contact us if
you experience any difficulties, or if you would like to express your views regarding our products.
Please write to:
Customer Services
Argos Ltd
489-499 Avebury Boulevard
Saxon gate West
Central Milton Keynes
MK9 2NW
Helpline: 0870 600 3030
Through the process of continuous improvement, Argos Limited reserves the right to change or alter
specifications without prior notice. E&OE
UK-13
AXM204UK Warranty
Hitachi Europe Ltd.
Product Guarantee
This product is guaranteed against manufacturing defects for a period of
This does not cover the product where the fault is due to misuse, abuse, use in contravention
of the instructions, or where the product has been the subject of unauthorised modifications or
alterations, or has been the
In the event of a problem with the product within the guarantee period please return it to your
nearest Argos store
If the item is shown to have had an inherent defect present at the time of sale, the store will
provide you with a replacement
Your statutory
iPod® is a registered trademark of Apple Computer, Inc., registered in the US and other countries.
1 year
subject of commercial use
rights remain unaffected
Guarantor; Argos Ltd
489 499 Avebur y Boulevard
Central Milton Keynes
MK9 2NW
Loading...