Harman-Kardon AVR 2000 User Manual

AVR 2000 Audio/VideoReceiver
AVR 2000
RDS
PTY
CT
RT
OWNER’S MANUAL
®
Power for the Digital Revolution
Table of Contents
3 Introduction 4 Safety Information 5 Front Panel Controls 7 Front Panel Information Display
9 Rear Panel Connections 11 Remote Control Functions 14 Installation and Connections 14 Audio Equipment Connections 14 Video Equipment Connections 15 SCART A/V Connections 16 System and Power Connections 17 System Configuration 17 Speaker Selection and Placement 18 First Turn On 18 Settings to be Made
With Each Input Used
18 Input Setup 18 Speaker Setup 20 Surround Setup 20 Making Settings independent of
selected Input
20 Delay Settings 21 Night Mode Settings 21 Output Level Adjustment 23 Operation 23 Basic Operation 23 Source Selection 23 Controls and Use of Headphones 24 Surround Mode Chart 25 Surround Mode Selection 25 Digital Audio Playback 25 Dolby Digital 25 DTS 25 PCM Audio Playback 26 MP3 Audio Playback 26 Selecting a Digital Source 26 Digital Status Indicators 27 Night Mode 27 Important Notes on Digital Playback 27 Tape Recording 28 Output Level Trim Adjustment 28 Display Brightness 28 Memory Backup 29 Tuner Operation 30 RDS Operation 32 Programming the Remote 32 Programming the Remote with Codes 33 Macro Programming 34 Programmed Device Function 34 Volume Punch-Through 35 Channel Control Punch-Through 35 Transport Control Punch-Through 35 Resetting the Remote Memory 36 Function List 38 Setup Code Tables 46 Troubleshooting Guide 46 Processor Reset 47 Technical Specifications
Declaration of Conformity
We,Harman Consumer International
2, route de Tours 72500 Château-du-Loir, FRANCE
declare in own responsibility, that the product described in this owner’s manual is in compliance with technical stan­dards:
EN 55013/6.1990
EN 55020/12.1994
EN 60065:1993
EN 61000-3-2/4.1995
Carsten Olesen
Harman Kardon Europe A/S
11/00
Typographical Conventions
In order to help you use this manual with the remote control, front-panel controls and rear-panel connections, certain conventions have been used.
EXAMPLE – (bold type) indicates a specific remote control or front-panel button, or rear-panel connection jack
EXAMPLE – (OCR type) indicates a message that is visible on the front-panel information display
1
– (number in a square) indicates a specific front-panel control
– (number in a circle) indicates a rear-panel connection
0
– (number in an oval) indicates a button or indicator on the remote
A
– (letter in a square) indicates an indicator in the front-panel display
2 TABLE OF CONTENTS
Introduction
Thank you for choosing Harman Kardon!
With the purchase of a Harman Kardon AVR 2000 you are about to begin many years of lis­tening enjoyment. The AVR 2000 has been cus­tom designed to provide all the excitement and detail of movie sound tracks and every nuance of musical selections.With onboard Dolby* Digital and DTS
decoding, the AVR 2000 deliv­ers six discrete channels of audio that take advantage of the digital sound tracks from the latest DVD and LD releases and Digital Television broadcasts.
While complex digital systems are hard at work within the AVR 2000 to make all of this happen, hookup and operation are simple. Color-keyed connections and a programmable remote con­trol make the AVR 2000 easy to use.To obtain the maximum enjoyment from your new receiv­er, we urge you to take the time to read through this manual. This will ensure that connections to speakers,source playback units and other exter­nal devices are made properly. In addition, a few minutes spent learning the functions of the various controls will enable you to take advan­tage of all the power the AVR 2000 is able to deliver.
If you have any questions about this product, its installation or its operation, please contact your dealer. He is your best local source of informa­tion.
Description and Features
The AVR 2000 is among the most versatile and multi-featured A/V receivers available, incorpo­rating a wide range of listening options.In addi­tion to Dolby Digital and DTS decoding for digi­tal sources, a broad choice of analog surround modes are available for use with sources such as CD,VCR,TV broadcasts and the AVR’s own FM/AM tuner. Along with Dolby Pro Logic*, Dolby 3 Stereo, 5 Ch Stereo and custom Hall and Theater modes,only Harman Kardon receivers offer Logic 7
®
to create a wider, more enveloping field environment and more defined fly-overs and pans. Finally, the AVR 2000 is among the very few A/V receivers that offer decoding of MP3 data, so that you may listen to the latest music selections directly from compatible com­puters or playback devices with the power and fidelity you expect from Harman Kardon. Another Harman Kardon exclusive is VMAx
,
which uses proprietary processing to create an open, spacious sound field even when only two front speakers are available.
In addition to providing a wide range of listening options, the AVR 2000 is easy to configure so that it provides the best results with your speak­ers and specific listening-room environment.
For the ultimate in flexibility, the AVR 2000 fea­tures connections for five video devices, all with both composite and S-Video inputs.Two addi­tional audio inputs are available, and a total of six digital inputs make the AVR 2000 capable of handling all the latest digital audio sources. Coax and optical digital outputs are available for direct connection to digital recorders.
The AVR 2000’s powerful amplifier uses traditional Harman Kardon high-current design technologies to meet the wide dynamic range of any program selection.
Harman Kardon invented the high-fidelity receiv­er more than forty-seven years ago.With state­of-the-art circuitry and time-honored circuit designs, the AVR 2000 is one of the finest receivers ever offered by Harman Kardon in its price range.
Onboard Dolby Digital and DTS Decoding Using Crystal
®
Chip
Technology
Harman Kardon’s Exclusive Logic 7 and VMAx Modes
MP3 Decoding for Use with compatible
Computers and Digital Audio Players
Front-Panel Digital Inputs for Easy
Connection to Portable Digital Devices and the Latest Video Game Consoles
Multiple Digital Inputs and Outputs
Remote with Internal Codes Capability
INTRODUCTION 3
Safety Information
Important Safety Information
Verify Line Voltage Before Use
Your AVR 2000 has been designed for use with 220-240-Volt AC current. Connection to a line voltage other than that for which it is intended can create a safety and fire hazard and may damage the unit.
If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your dealer before plugging the unit into a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards,use only the power cord attached to your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on them. Damaged power cords should be replaced immediately by an authorized service depot with a cord meeting factory specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always pull the plug, never pull the cord. If you do not intend to use the unit for any con­siderable length of time, disconnect the plug from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your guarantee. If water or any metal object such as a paper clip, wire or a staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service station.
Installation Location
To assure proper operation and to avoid the potential for safety hazards, place the unit on a firm and level surface.When placing the unit on a shelf,be certain that the shelf and any mounting hardware can support the weight of the product.
Make certain that proper space is provided both above and below the unit for ventilation. If this product will be installed in a cabinet or other enclosed area, make certain that there is sufficient air movement within the cabinet. Under some circumstances a fan may be required.
Do not place the unit directly on a carpeted surface.
Avoid installation in extremely hot or cold locations, or an area that is exposed to direct sunlight or heating equipment.
Avoid moist or humid locations.
Do not obstruct the ventilation slots on the
top of the unit, or place objects directly over them.
Cleaning
When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary, wipe it with a soft cloth dampened with mild soapy water, then a fresh cloth with clean water. Wipe dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of metal parts.Avoid spraying insecticide near the unit.
Moving the Unit
Before moving the unit, be certain to disconnect any interconnection cords with other components, and make certain that you disconnect the unit from the AC outlet.
Unpacking
The carton and shipping materials used to protect your new receiver during shipment were specially designed to cushion it from shock and vibration.We suggest that you save the carton and packing materials for use in shipping if you move, or should the unit ever need repair.
To minimize the size of the carton in storage, you may wish to flatten it. This is done by carefully slitting the tape seams on the bottom and collapsing the carton. Other cardboard inserts may be stored in the same manner. Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag.
If you do not wish to save the packaging materials, please note that the carton and other sections of the shipping protection are recyclable. Please respect the environment and discard those materials at a local recycling center.
4 SAFETY INFORMATION
Front Panel Controls
4
1
3
5
7
8
9
)
!
@
#
$
%
^
* &
(
29
2
6
Ò
ˆ
Ù
AVR 2000
ı
Û
Ú
Ô
Ó
RDS
RDS
PTY
CT
RT
TA
Main Power Switch
1
System Power Control
2
Power Indicator
3
Headphone Jack
4
Selector Buttons
5
Tone Mode
6
Surround Mode Selector
7
Tuning
8
Tuner Band Selector
9
Preset Stations Selector
)
1
Main Power Switch: Press this button to
apply power to the AVR 2000. When the switch is pressed in, the unit is placed in a Standby mode, as indicated by the amber LED rounding the System Power Control button MUST be pressed in to operate the unit. To turn the unit off completely and prevent the use of the remote control, this switch should be pressed until it pops out from the front panel so that the word “OFF” may be read at the top of the switch.
NOTE:This switch is normally left in the “ON” position.
3
2
sur-
. This
Input Source Selector
!
RDS Select Button
@
Digital Optical 3 Input
#
Digital Coax 3 Input
$
Video 4 input jacks
%
Bass Control
^
Balance Control
&
Treble Control
*
Volume Control
(
Set Button
Ó
2
System Power Control:When the Main
Power Switch
turn on the AVR 2000; press it again to turn the unit off (to Standby). Note that the Power Indicator surrounding the switch green when the unit is on.
3
Power Indicator: This LED will be illumi-
nated in amber when the unit is in the Standby mode to signal that the unit is ready to be turned on. When the unit is in operation, the indicator will turn green.
4
Headphone Jack: This jack may be used to
listen to the AVR 2000’s output through a pair of headphones. Be certain that the headphones have a standard 6.3 mm stereo phone plug. Note that the speakers will automatically be turned off when the headphone jack is in use.
1
is “ON,”press this button to
3
will turn
Input Indicators
Ô
Delay
Digital Input Selector
Ò
Main Information Display
Ú
Channel Select Button
Û
Speaker Select Button
Ù
Test Tone Selector
ı
Surround Mode Indicators
ˆ
Remote Sensor Window
˜
5
Selector Buttons: When you are establish-
ing the AVR 2000’s configuration settings,use these buttons to select from the choices available, as shown in the Main Information Display
6
Tone Mode: Pressing this button enables or
disables the Balance, Bass and Treble tone con­trols.When the button is pressed so that the words TONE IN appear in the Main
Information Display Bass
^
and Treble*controls and of the
Balance control
nals.When the button is pressed so that the words TONE OUT appear in the Main
Information Display
will be “flat,” without any balance,bass or treble alteration.
Ú
, the settings of the
&
will affect the output sig-
Ú
, the output signal
Ú
.
FRONT PANEL CONTROLS 5
Front Panel Controls
7
Surround Mode Selector: Press this but-
ton to change the surround mode by scrolling through the list of available modes. Note that Dolby Digital and DTS modes can be selected only when a digital input is used (See page 24 for more information about surround modes.)
8
Tuning Selector: Press the left side of the
button to tune lower frequency stations and the right side of the button to tune higher frequency stations.When a station with a strong signal is reached, the TUNED indicator in the Main Information Display (see page 29 for more information on tuning stations).
9
Tuner Band Selector: Pressing this button
will automatically switch the AVR to the Tuner mode. Pressing it again will switch between the AM and FM frequency bands, holding it pressed for some seconds will switch between stereo and mono receiving and between automatic and manual tuning mode (See page 29 for more information on the tuner).
)
Preset Stations Selector: Press this but-
ton to scroll up or down through the list of sta­tions that have been entered into the preset memory. (See page 29 for more information on tuner programming.)
!
Input Source Selector: Press this button
to change the input by scrolling through the list of input sources.
@ RDS Select Button: Press this button to dis- play the various messages that are part of the RDS data system of the AVR 2000’s tuner. (See page 30 for more information on RDS).
#
Digital Optical 3 Input: Connect the opti-
cal digital audio output of an audio or video prod­uct to this jack.When the Input is not in use, be certain to keep the plastic cap installed to avoid dust contamination that might degrade future performance.
V
will illuminate
Ú
$
Digital Coax 3 Input: This jack is normally
used for connection to the output of portable digital audio devices, video game consoles or other products that have a coax digital jack.
%
Video 4 Input Jacks: These audio/video
jacks may be used for temporary connection to video games or portable audio/video products such as camcorders and portable audio players.
^
Bass Control: Turn this control to modify the
low frequency output of the left/right channels by as much as ±10dB. Set this control to a suitable position for your taste or room acoustics.
&
Balance Control: Turn this control to
change the relative volume for the front left/right channels.
NOTE: For proper operation of the surround modes this control should be at the midpoint or “12 o’clock” position.
*
Treble Control:Turn this control to modify
the high frequency output of the left/right chan­nels by as much as ±10dB. Set this control to a suitable position for your taste or room acoustics.
(
Volume Control:Turn this knob clockwise
to increase the volume, counterclockwise to decrease the volume. If the AVR is muted, adjusting volume control will automatically release the unit from the silenced condition.
Ó
Set Button: When making choices during
the setup and configuration process,press this button to enter the desired setting as shown in the Main Information Display AVR 2000’s memory. The set button may also be used to change the display brightness. (See page 28.)
Ú
into the
Ô
Input indicators: A green LED will light in
front of the input that is currently being used as the source for the AVR 2000.
Delay: Press this button to begin the
sequence of steps required to enter delay time settings. (See page 20 for more information on delay times.)
Ò
Digital Input Selector: When playing a
source that has a digital output, press this button to select between the Optical and Coaxial 25-27 for more information on digital audio.)
Ú
delivers messages and status indications to help you operate the receiver. (See pages 7–8 for a complete explanation of the Information Display.)
Û
Channel Select Button: Press this button
to begin the process of trimming the channel output levels using an external audio source. (For more information on output level trim adjustment, see page 28.)
Ù
Speaker Select Button: Press this button
to begin the process of selecting the speaker positions that are used in your listening room. (See page 19 for more information on setup and configuration.)
ı
Test Tone Selector: Press this button to
begin the process of adjusting the channel out­put levels using the internal test tone as a refer­ence. (For more information on output level adjustment, see page 21.)
ˆ
Surround Mode Indicators: A green LED
will light in front of the surround mode that is currently in use.
˜
behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed.
$
Digital inputs. (See pages
Main Information Display: This display
Remote Sensor Window:The sensor
#
6 FRONT PANEL CONTROLS
Front Panel Information Display
COAXIAL
THEATER
5 CH STEREO
HALL
3
-
STEREO
PRO LOGIC
DIGITAL
DTS
DOLBY D
PCM MP3
NIGHT
OPTICAL
ANALOG
LFE
0CL0
1 2 3
1 2 3
MEMORY PRESET
SLEEP
AUTO
5.1 LOGIC 7 CM
VMAx NF
MUTE
TUNED ST
A
B
D
E
M
N
K
L
S
T
R
QP
X
W
V
U
F
H
I
J
O
O
R
O
O
LS
O
O
RS
O
O
C
G
RDS
AE
PTY
ADCTACRTABTAAA
O
A
Bitstream Indicators
B
Optical Source Indicators
C
DTS Mode Indicator
D
Dolby Digital Indicator
E
Coaxial Source Indicators
F
Dolby Pro Logic Indicator
G
Analog Input Indicator
H
Dolby 3 Stereo Indicator
I
VMAx Mode Indicator
J
5 Channel Stereo Indicator
A
Bitstream™ Indicators:When the input is a
digital source, one of these indicators will light to display the specific type of signal in use.
B
Optical Source Indicators: These indica-
tors light to show when a Optical Digital Input has been selected.
C
DTS Mode Indicator: This indicator illumi-
nates when the DTS mode is selected.
D
Dolby Digital Indicator: This indicator illu-
minates when Dolby Digital mode is selected.
E
Coaxial Source Indicators: These indica-
tors light to show when a Coaxial Digital Input has been selected.
F
Dolby Pro Logic Indicator: This indicator
lights when the Dolby ProLogic mode has been selected.
G
Analog Input Indicator: This indicator
lights when an analog input source has been selected.
H
Dolby 3 Stereo Indicator: This indicator
lights when the Dolby 3 Stereo Mode has been selected.
I
VMAx Mode Indicator: This indicator illu-
minates to show that the VMAx mode is in use. VMAx F appears when the Far Field VMAx mode is selected; VMAxN appears when the Near Field VMAx mode is selected. (See page 24 for a description of the VMAx Modes.)
K
Logic 7 Mode Indicators
L
Hall Mode Indicator
M
Theater Mode Indicator
N
Night Mode Indicator
O
Mute Indicator
P
Speaker/Channel Input Indicators
Q
Preset Number/Sleep Timer
R
Preset Indicator
R
Sleep Indicator
T
Memory Indicator
J
5 Channel Stereo Indicator: This indica-
tor lights when the 5 Channel Stereo mode has been selected.
K
Logic 7 Mode Indicators: These indicators
illuminate when the Logic 7 mode is in use. LOGIC 7Cappears for the Cinema version of Logic 7, LOGIC 7M appears for the Music version of Logic 7. (See page 24 for a description of the Logic 7 Modes.)
L
Hall Mode Indicator: This indicator lights
when the Hall mode has been selected.
M
Theater Mode Indicator: This indicator illu-
minates to show that the Theater mode is in use.
N
Night Mode Indicator: This indicator
lights when the AVR 2000 is in the Night mode, which preserves the dynamic range of digital program material at low volume levels.
O
Mute Indicator: This indicator illuminates
to remind you that the AVR 2000’s output has been silenced by pressing the Mute button
. Press the Mute button again to return to
the previously selected output level.
U
Stereo Indicator
V
Tuned Indicator
W
Auto Indicator
X
Main Information Display
AA
Traffic Indicator
AB
Radiotext Indicator
AC
Clock Timer Indicator
AD
Program Type Indicator
AE
RDS Indicator
P
Speaker/Channel Input Indicators: These
indicators are multipurpose, indicating either the speaker type selected for each channel or the incoming data-signal configuration.The left,cen­ter, right, right surround and left surround speaker indicators are composed of three boxes, while the subwoofer is a single box.The center box lights when a “Small” speaker is selected, and the two outer boxes light when “Large” speakers are selected.When none of the boxes are lit for the center, surround or subwoofer channels, no speaker has been selected for that position. (See page 18 for more information on configuring speakers.) The letters inside each of the center boxes display active input channels. For standard analog inputs, only the L and R will light,indicat­ing a stereo input.When a digital source is play­ing, the indicators will light to display the chan­nels begin received at the digital input.When the letters flash, the digital input has been interrupt­ed. (See page 26 for more information on the Channel Indicators).
Q
Preset Number/Sleep Timer: When the
tuner is in use, these numbers indicate the spe­cific preset memory location in use. (See page 29 for more information on preset stations.) When the Sleep function is in use, these numbers show how many minutes remain before the unit goes into the Standby mode.
FRONT PANEL INFORMATION DISPLAY 7
Front Panel Information Display
R
Preset Indicator: This indicator lights when
the tuner is in use to show that the Preset
Number/Sleep Timer
tion’s preset memory number. (See page 29 for more information on tuner presets.)
S
Sleep Indicator: This indicator lights when
the Sleep function is in use.The numbers in the Preset/Sleep Number Indicators will show the minutes remaining before the AVR 2000 goes into the Standby mode. (See page 23 for more information on the Sleep function.)
T
Memory Indicator: This indicator flashes
when entering presets and other information into the tuner’s memory.
U
Stereo Indicator: This indicator illuminates
when an FM station is being tuned in stereo.
V
Tuned Indicator: This indicator illuminates
when a station is being received with sufficient sig­nal strength to provide acceptable listening quality.
W
Auto Indicator: This indicator illuminates
when the tuner’s Auto mode is in use.
X
Main Information Display: This display
shows messages relating to the status, input source, surround mode, tuner, volume level or other aspects of unit’s operation.
Q
is showing the sta-
AA
This indicator illuminates if the RDS station tuned somtimes transmits traffic information (see page 30 for more information on RDS).
AB
nates when the RDS station tuned is transmit­ting radiotext (RT) data.
AC
minates when the RDS station tuned is transmit­ting the CT (clock time) code, indicating the cur­rent time of day.
AD
when the RDS station tuned is transmitting pro­gram type data, or during a PTY search.
AE
when the station tuned is transmitting RDS data.
TA Traffic Announcement Indicator:
RT Text Indicator: This indicator illumi-
Clock Time Indicator: This indicator illu-
PTY Indicator: This indicator illuminates
RDS Indicator: This indicator illuminates
8 FRONT PANEL INFORMATION DISPLAY
Rear Panel Connections
AC INPUT
~230V/50HZ A
TAPE
FRONT SPKRS (8)
RIGHT LEFT
CENTER
SPKR (8)
ANTENNA
DIGITAL IN
DIGITAL OUT
VID 3 VID 3
REMOTE
VID 2 VID 2
OPT
OPT
COAX
COAX
VID 1 VID 1
DVD DVD
CD
MON. OUT
IN
OUT
AM
GND
FM
75
IN
OUT
1
2
1
2
IN
OUT
IN
OUT
IN
OUT
L R L R
VIDEO S-VIDEO
+
+
SURR. SPKRS (8)
SERIAL NO.
RIGHT LEFT
¤
°
·
a
b
c
d
e
j
¢
§
SUBWOOFER
IN
OUT
f
i
ª
¡
£
∞ ¶
g
MODEL NO. AVR 2000
NORTHRIDGE
CALIFORNIA, USA
MADE IN CHINA
AC OUTLETS
~230V/50Hz
UNSWITCHED / 100W MAX
SWITCHED / 50W MAX
h
Tape Inputs
Tape Outputs
Video 1 Audio Inputs
AM Antenna
Video 1 Audio Outputs
DVD Audio Inputs
FM Antenna
CD Inputs
Digital Audio Outputs
Subwoofer Output
Tape Inputs: Connect these jacks to the
PLAY/OUT jacks of an audio recorder.
Tape Outputs: Connect these jacks to the
RECORD/INPUT jacks of an audio recorder.
Video 1 Audio Inputs: Connect these jacks
to the PLAY/OUT audio jacks on a VCR or other video source.
supplied with the receiver to theseterminals.If an external AMantenna is used,make connections to the AM and GND terminals in accordance with the instructions supplied with the antenna.
AM Antenna:Connect theAM loop antenna
Video Monitor Outputs
Front/Center Speaker Outputs
Surround Speaker Outputs
Switched AC Accessory Outlet
Unswitched AC Accessory Outlet
AC Power Cord
Remote IR Output
Remote IR Input
DVD Video Inputs
Video 1 Video Outputs
Video 1 Audio Outputs: Connect these
jacks to the RECORD/INPUT audio jacks on a VCR or any other Audio recorder.
DVD Audio Inputs: Connect these jacks to
the analog audio jacks on a DVD or other video source.
FM Antenna: Connect the supplied indoor or
an optional external FM antenna to this terminal.
CD Inputs: Connect these jacks to the ana-
log output of a compact disc player or CD changer.
Video 3 Video Inputs
Video 2 Video Inputs
Video 2 Video Outputs
Video 1 Video Inputs
Optical Digital Inputs
Coaxial Digital Inputs
Video 3 Audio Inputs
Video 2 Audio Inputs
Video 2 Audio Outputs
Digital Audio Outputs: Connect these
jacks to the matching digital input connector on a digital recorder such as a CD-R or MiniDisc recorder.
Subwoofer Output: Connect this jack to
the line-level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input.
Video Monitor Outputs: Connect these
jacks to the composite and/or S-Video input of a TV monitor or video projector to view the output of any video source selected by the receiver’s video switcher.
REAR PANEL CONNECTIONS 9
Rear Panel Connections
Front/Center Speaker Outputs: Connect
these outputs to the matching + or – terminals on your front/center speakers.When making speaker connections,always make certain to maintain correct polarity by connecting the red (+) terminals on the AVR 2000 to the red (+) terminals on the speaker and the black (–) ter­minals on the AVR 2000 to the black (–) termi­nals on the speakers.(See page 14 for more information on speaker polarity.)
Surround Speaker Outputs: Connect
these outputs to the matching + or – terminals on your left and right surround speakers.When making speaker connections always make cer­tain to maintain correct polarity by connecting the red (+) terminals on the AVR 2000 to the red (+) terminals on the speakers and the black (–) terminals on the AVR 2000 to the black (–) terminals on the speakers.See page 14 for more information on speaker polarity.
Switched AC Accessory Outlet: This out-
let may be used to power any device that you wish to have turn on when the unit is turned on with the System Power Control switch
Unswitched AC Accessory Outlet: This
outlet may be used to power any AC device. The power will remain on at this outlet regardless of whether the AVR 2000 is on or off (in Standby), provided that the Main Power switch
Note: The total power consumption of all devices connected to the accessory outlets should not exceed 100 watts from the
Unswitched Outlet Switched Outlet
and 50 W from the
.
1
2
is on.
.
AC Power Cord: Connect the AC plug to an
unswitched AC wall output.
Remote IR Output: This connection per-
mits the IR sensor in the receiver to serve other remote controlled devices. Connect this jack to the “IR IN” jack on Harman Kardon or other compatible equipment.
Remote IR Input: If the AVR 2000’s front-
panel IR sensor is blocked due to cabinet doors or other obstructions, an external IR sensor may be used. Connect the output of the sensor to this jack.
DVD Video Inputs: Connect these jacks to
the composite or S-Video output jacks on a DVD player or other video source.
Video 1 Video Outputs: Connect these
jacks to the RECORD/INPUT composite or S-Video jack on a VCR.
Video 3 Video Inputs: Connect these jacks
to the PLAY/OUT composite or S-Video jacks on any video source.
Video 2 Video Inputs: Connect these jacks
to the PLAY/OUT composite or S-Video jacks on a second VCR or other video source.
Video 2 Video Outputs: Connect these
jacks to the RECORD/INPUT composite or S-Video jacks on a second VCR.
Video 1 Video Inputs: Connect these jacks
to the PLAY/OUT composite or S-Video jacks on a VCR or other video source.
Optical Digital Inputs: Connect the optical
digital output from a DVD player, HDTV receiver, LD player, MD player or CD player to these jacks. The signal may be either a Dolby Digital signal, a DTS signal or a standard PCM digital source.
Coaxial Digital Inputs: Connect the coax
digital output from a DVD player, HDTV receiver, LD player, MD player or CD player to these jacks. The signal may be either a Dolby Digital signal, DTS signal or a standard PCM digital source. Do not connect the RF digital output of an LD play­er to these jacks.
Video 3 Audio Inputs: Connect these jacks
to the PLAY/OUT audio jacks on any audio or video source.
Video 2 Audio Inputs: Connect these jacks
to the PLAY/OUT audio jacks on a VCR or other video source.
Video 2 Audio Outputs: Connect these
jacks to the RECORD/INPUT audio jacks on a VCR or any Audio recorder.
Note: Either the Video or S-Video output of any S-Video source must be connected to the AVR 2000, not both in parallel, otherwise the video may be disturbed or its performance be adverse­ly effected.
10 REAR PANEL CONNECTIONS
Remote Control Functions
POWER
AVR
AM/FM
VCR
OFF
ON
SLEEP
SURR.
PR
C
H
.
D
I
G
I
T
A
L
M
E
N
U
S
P
K
R
N
O
R
M
A
L
D
E
L
A
Y
SET
TUN-M
MEM
RDS
DIRECT
TUNING
PRESET
CLEAR
DWN
UP
TEST
NIGHT
2000
SKIP
a
bc
d
e
f
g
h
i
j
k
l
m
o
n
p
m
r
q
s
t
u
y
30
28
`
DVD
CD
TAPE
VID 2
TV
CBL/SAT
VID 4VID 1
VID 3
1
2
3
4
7
6
5
9
0
8
M2
M3
M4
M1
z
VOL.
33
32
31
29
34
y
v
w
0
Power On Button
1
IR Transmitter Window
2
Program Indicator
3
Power Off Button
4
Input Selectors
5
AVR Selector
6
AM/FM Tuner Select
7
Test Button
8
Sleep Button
9
Surround Mode Selector
A
Night Mode
B
Channel Select Button
⁄/¤
C D E F G H I J K L M N O P Q  
! " # 
Buttons
Button Set Button Digital Select Numeric Keys Tuner Mode Direct Button Tuning Up/Down Macro Buttons Transport Controls Skip Up/Down Buttons RDS Select Button Preset Up/Down Clear Button Memory Button Delay/Prev. Ch.
Button Speaker Select Spare Button Volume Up/Down TV/Video Selector Mute
NOTE:The function names shown here are each button’s feature when used with the AVR. Most buttons have additional functions when used with other devices. See page 36 for a list of these functions.
REMOTE CONTROL FUNCTIONS 11
Remote Control Functions
90
min80min70min60min50min
40
min
30
min20min10min
OFF
IMPORTANT NOTE: The AVR 2000’s remote may be programmed to control up to seven devices, including the AVR 2000. Before using the remote, it is important to remember to press the Input Selector button
4
that corre­sponds to the unit you wish to operate.In addi­tion, the AVR 2000’s remote is shipped from the factory to operate the AVR 2000 and most Harman Kardon CD or DVD players and cassette decks.The remote is also capable of operating a wide variety of other products using the control codes that are part of the remote. Before using the remote with other products, follow the instructions on pages 32 to program the proper codes for the products in your system.
It is also important to remember that many of the buttons on the remote take on different func­tions, depending on the product selected using the Input Selectors.The descriptions shown here primarily detail the functions of the remote when it is used to operate the AVR 2000. (See page 36 for information about alternate functions for the remote’s buttons.)
0
Power On Button: Press this button to
turn on the power to a device selected by pressing one of the Input Selectors
1
IR Transmitter Window: Point this window
4
(except Tape).
towards the AVR 2000 when pressing buttons on the remote to make certain that infrared com­mands are properly received.
2
Program Indicator: This three-color indi-
cator is used to guide you through the process of programming the remote.See page 32 for infor­mation on programming the remote.
3
Power Off Button: Press this button to
place the AVR 2000 or a selected device unit in the Standby mode.
4
Input Selectors: Pressing one of these
buttons will perform three actions at the same time. First,if the AVR is not turned on, this will power up the unit. Next, it will select the source shown on the button as the input to the AVR. Finally, it will change the remote control so that it controls the device selected. After pressing one of these buttons you must press the AVR Selector button
5
again to operate the
AVR’s functions with the remote.
5
AVR Selector: Pressing this button will
switch the remote so that it will operate the AVR’s functions. If the AVR is in the Standby mode,it will also turn the AVR on.
6
AM/FM Tuner Select: Press this button to
select the AVR’s tuner as the listening choice. Pressing this button when the tuner is in use will select between the AM and FM bands.
7
Test Tone: Press this button to begin the
sequence used to calibrate the AVR 2000’s output levels. (See page 21 for more information on calibrating the AVR 2000.)
8
Sleep Button: Press this button to place
the unit in the Sleep mode.After the time shown in the display, the AVR 2000 will automatically go into the Standby mode. Each press of the button changes the time until turn-off in the fol­lowing order:
Hold the button pressed for two seconds to turn off the Sleep mode setting. Note that this button is also used to change channels on your TV,VCR and SAT receiver when selected.
9
Surround Mode Selector: Press this
button to begin the process of changing the surround mode. After the button has been pressed, use the
⁄/¤
buttons Cto select the desired surround mode (See page 25 for more information). Note that this button is also used to tune channels when the TV,VCR and SAT receiver is selected using the Input
Selector
A
4
.
Night Mode: Press this button to activate
the Night mode.This mode is available only with Dolby Digital encoded digital sources, and it pre­serves dialog (center channel) intelligibilty at low volume levels (See page 27 for more informa­tion).
B
Channel Select Button: This button is
used to start the process of setting the AVR 2000’s output levels with an external source. Once this button is pressed, use the
⁄/¤
buttonsCto
select the channel being adjusted, then press the Set button
E
, followed by the
⁄/¤
buttons again, to change the level setting. (See page 28 for more information.)
⁄/¤
C
Buttons: These are multi-purpose
buttons. They will be used most frequently to select a surround mode.These buttons are also used to increase or decrease output levels when config­uring the unit, to select speaker configuration or to select the digital inputs.They are also used to enter delay time settings after the Delay button
has been pressed.
When the AVR 2000 remote is being programmed for the codes of another device, these buttons are also used in the “Auto Search” process (See page 32 for more information on programming the remote.)
D‹Button: This button does not have a function with the AVR2000. When a DVD player or TV is selected,it may be used to navigate the menus of those devices.
E
Set Button: This button is used to enter
settings into the AVR 2000’s memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjustment.
F
Digital Select: Press this button to assign
one of the digital inputs
#$
to a source. (See page 26 for more information on using digital inputs.)
G
Numeric Keys:These buttons serve as a
ten-button numeric keypad to enter tuner preset positions.They are also used to select channel numbers when TV, VCR or Sat receiver has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed.
H
Tuner Mode: Press this button when the
tuner is in use to select between automatic tun­ing and manual tuning. When the button is pressed so that the AUTO indicator out, pressing the Tuning buttons
W
goes
J8will
move the frequency up or down in single-step increments.When the FM band is in use and the AUTO indicator
W
is on, pressing this button will change to monaural reception making even week stations audible. (See page 29 for more information.)
12 REMOTE CONTROL FUNCTIONS
Remote Control Functions
I
Direct Button: Press this button when the
tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the button simply press the proper Numeric Keys
G
to select a station (See page 29 for more
information on the tuner).
J
Tuning Up/Down:When the tuner is in use,
these buttons will tune up or down through the selected frequency band. If the Tuner Mode but- ton
H
has been pressed or the Band button
@
on the front panel was held pressed so that
the AUTO indicator either of the buttons will cause the tuner to seek the next station with acceptable signal strength for quality reception.When the AUTO indicator
W
is NOT illuminated, pressing these buttons will tune stations in single-step increments. (See page 29 for more information.)
K
Macro Buttons: Press these buttons
to store or recall a “Macro”, which is a pre-programmed sequence of commands stored in the remote. (See page 33 for more information on storing and recalling macros.)
L
Transport Buttons: These buttons do not
have any functions for the AVR, but they may be programmed for the forward/reverse play opera­tion of a wide variety of CD or DVD players, and audio or video- cassette recorders. (See page 32 for more information on programming the remote.)
M
Skip Up/Down Buttons: These buttons
do not have a direct function with the AVR 2000, but when used with a compatibly pro­grammed CD or DVD changer they will change the tracks on the disc currently being played in the changer.
N
RDS Select Button: Press this button to
display the various messages that are part of the RDS data system of the AVR 2000’s tuner. (See page 30 for more information on RDS).
W
is illuminated, pressing
O
Preset Up/Down: When the tuner is in
use, press these buttons to scroll through the stations programmed into the AVR 2000’s mem­ory.When CD or DVD is selected using the Input Selector button
4
, these buttons may
function as Slow Fwd/Rev (DVD) or ”+10” (CD).
P
Clear Button: Press this button to clear
incorrect entries when using the remote to directly enter a radio station’s frequency.
Q
Memory Button: Press this button to enter
a radio station into the AVR 2000’s preset memory.After pressing the button the MEMORY indicator
T
will flash; you then have five sec-
onds to enter a preset memory location using the Numeric Keys
G
. (See page 29 for more
information.)
Delay/Prev Ch.: Press this button to begin
the process for setting the delay times used by the AVR 2000 when processing surround sound. After pressing this button, the delay times are entered by pressing the Set button then using the
⁄/¤
buttons Cto change the
E
and
setting. Press the Set button again to complete the process. (See page 20 for more information.)
›Button: This button does not have a function with the AVR2000. When a DVD player or TV is selected,it may be used to navigate the menus of those devices.
Speaker Select: Press this button to
begin the process of configuring the AVR 2000’s Bass Management System for use with the type of speakers used in your system. Once the button has been pressed, use the tons
C
to select the channel you wish to set
up. Press the Set button
E
⁄/¤
and then select
but-
the speaker type (see page 18 for more infor­mation.)
!
Spare Button: This button does not have
any function for the operation of the AVR 2000, but it can turn on/off the Multiroom system on other Harman Kardon AV-receivers with that fea­ture and the Sub-function on DVD players.
"
Volume Up/Down: Press these buttons to
raise or lower the system volume.
#
TV/Video Button: This button does not
have a direct function on the AVR 3000, but when used with a compatibly programmed VCR, DVD or satellite receiver that has a “TV/Video” function, pressing this button will switch between the output of the player or receiver and the external video input to that player. Consult the Owner’s Manual for your specific player or receiver for the details of how it implements this function.
Mute: Press this button to momentarily
silence the AVR 2000 or TV set being controlled, depending on which device has been selected.
When the AVR 2000 remote is being programmed to operate another device,this button is pressed with the Input Selector button
4
to begin the programming process. (See page 32 for more information on programming the remote.)
NOTE: As any of the remote buttons pressed is active with the device selected, the correspon­ding Selector button
45
will briefly flash
red to confirm your selection.
REMOTE CONTROL FUNCTIONS 13
Installation and Connections
After unpacking the unit, and placing it on a solid surface capable of supporting its weight, you will need to make the connections to your audio and video equipment.
Audio Equipment Connections
We recommend that you use high-quality inter­connect cables when making connections to source equipment and recorders to preserve the integrity of the signals.
When making connections to audio source equipment or speakers it is always a good prac­tice to unplug the unit from the AC wall outlet. This prevents any possibility of accidentally send­ing audio or transient signals to the speakers that may damage them.
1. Connect the analog output of a CD player to the CD inputs
NOTE:When the CD player has both fixed and variable audio outputs it is best to use the fixed output unless you find that the input to the receiver is so low that the sound is noisy, or so high that the signal is distorted.
2. Connect the analog Play/Out jacks of a cas­sette deck, MD,CD-R or other audio recorder to the Tape Input jacks Record/In jacks on the recorder to the Tape Output jacks
3. Connect the output of any digital sources to the appropriate input connections on the AVR 2000 front or rear panel. Note that the Optical and Coaxial digital inputs
#$
or DTS source or the output of a conventional CD, MD or LD player’s PCM (S/P-DIF) output.
4. Connect the Coaxial or Optical Digital
Outputs
matching digital input connections on a CD-R or MiniDisc recorder.
5. Assemble the AM Loop Antenna supplied with the unit as shown below. Connect it to the AM and GND screw terminals
6. Connect the supplied FM antenna to the FM (75 ohm) connection be an external roof antenna, an inside powered or wire lead antenna or a connection from a cable system. Note that if the antenna or con­nection uses 300-ohm twin-lead cable, you must use a 300-ohm-to-75-ohm adapter to make the connection.
.
. Connect the analog
on the AVR 2000.
may be used with a Dolby Digital
on the rear panel of the AVR to the
.
. The FM antenna may
7. Connect the front, center and surround speak­er outputs

to the respective speakers.
To assure that all the audio signals are carried to your speakers without loss of clarity or resolu­tion, we suggest that you use high-quality speaker cable.Many brands of cable are avail­able and the choice of cable may be influenced by the distance between your speakers and the receiver, the type of speakers you use, personal preferences and other factors.Your dealer or installer is a valuable resource to consult in selecting the proper cable.
Regardless of the brand of cable selected, we recommend that you use a cable constructed of fine, multistrand copper with an area greater than 2 mm
Cable with an area of 1.5 mm
2
.
2
may be used for short runs of less than 4 m.We do not recom­mend that you use cables with an area less than
2
1mm
due to the power loss and degradation in
performance that will occur.
Cables that are run inside walls should have the appropriate markings to indicate listing with UL, CSA or other appropriate testing agency stan­dards. Questions about running cables inside walls should be referred to your installer or a licensed electrical contractor who is familiar with the applicable local building codes in your area.
When connecting wires to the speakers,be cer­tain to observe proper polarity. Remember to connect the “negative” or “black” wire to the same terminal on both the receiver and the speaker. Similarly, the “positive” or “red” wire should be connected to like terminals on the AVR 2000 and speaker.
NOTE:While most speaker manufacturers adhere to an industry convention of using black terminals for negative and red ones for positive, some manufacturers may vary from this configu­ration.To assure proper phase and optimal per­formance, consult the identification plate on your speaker or the speaker’s manual to verify polarity. If you do not know the polarity of your speaker, ask your dealer for advice before pro­ceeding, or consult the speaker’s manufacturer.
We also recommend that the length of cable used to connect speaker pairs be identical. For example, use the same length piece of cable to connect the front-left and front-right or sur­round-left and surround-right speakers,even if the speakers are a different distance from the AVR 2000.
8. Connections to a subwoofer are normally made via a line level audio connection from the
Subwoofer Output
to the line-level input of a subwoofer with a built-in amplifier. When a passive subwoofer is used, the connection first goes to a power amplifier, which will be con-
nected to one or more subwoofer speakers.If you are using a powered subwoofer that does not have line-level input connections, follow the instructions furnished with the speaker for con­nection information.
Note: Speaker sets with two front satellites and a passive subwoofer must be connected to the front speaker outputs
Subwoofer Output
only rather than to the
.
Video Equipment Connections
Video equipment is connected in the same man­ner as audio components.Again, the use of high­quality interconnect cables is recommended to preserve signal quality.To ensure best video per­formance S-Video sources should be connected to the AVR 2000 only with their S-Video In/ Outputs, not with their composite video connec­tors too.
1. Connect a VCR’s audio and video Play/Out jacks to the Video 1 or Video 2 In jacks

Video Record/In jacks on the VCR should be con­nected to the Video 1 or Video 2 Out jacks

2. Connect the analog audio and video outputs of a satellite receiver, cable TV converter or tele­vision set or any other video source to the
Video 2
jacks.
3. Connect the analog audio and video outputs of a DVD or laser disc player to the DVD jacks

4. Connect the Video Monitor Out the receiver to the composite and S-Video input of your television monitor or video projector.
Video Connection Note:
• S-Video or Composite video signals may only be viewed in their native formats and will not be converted to the other format.
on the rear panel. The Audio and
on the AVR 2000.

(if not in use) or Video 3
.

jacks on
14 INSTALLATION AND CONNECTIONS
Installation and Connections
Black
Yellow
Red
Black
Red
Blue
Yellow
Green
White
Black
Yellow
Red
Rot
Schwarz
S-Video In
Schwarz
Rot
Blau Gelb
S-Video In
S-Video Out
Rot
Schwarz
S-Video Out
SCART A/V Connections
For the connections described above your video device needs RCA (cinch) connectors or/and S­Video connectors for all Audio and Video signals: Any normal video device (Not SVHS or High 8) for only playback needs 3 RCA jacks,VCRs for record and playback even 6 RCA jacks.Any S­Video device (SVHS, High 8) needs 2 RCA (Audio) and 1 S-Video jack (Video), if it´s a playback unit, or 4 RCA (Audio In/Out) and 2 S-Video (Video In/Out) jacks, if it´s a recording VCR.
Many european video devices are equipped with RCA (Cinch) or S-Video jacks only partially,not for all audio and video in/outputs needed as described above, but with a so called Scart or Euro-AV connector (almost rectangular jack with 21 pins, see drawings on this page).
In that case the following Scart to Cinch adapters or cables are needed:
• Units for playback, such as satellite receivers, camcorders, DVD or LD players, need an adapter from Scart to 3 RCA plugs, see fig.1 (normal video devices) or from Scart to 2 RCA+1 S-Video plugs, see fig. 4 (S-Video devices).
• HiFi VCRs need an adapter from Scart to 6 RCA plugs, see fig.2 (normal video), or from Scart to 4 Audio+2S-Video jacks, see fig.5 (S-Video VCR). Read carefully the instruction attached to the adapter to find which of the six plugs is used for the record signal to the VCR (connect with the AVR´s Out jacks) and for the playback signal from the VCR (connect with the AVR´s In jacks). Do not misconnect Audio and Video signals. Don´t hesitate to consult your dealer, if you are uncertain.
• If you use only normal video devices the TV monitor needs an adapter from 3 RCA plugs to Scart (fig. 3) only. If also S-Video devices are used an adapter from 2 RCA+1S-Video plugs to Scart is needed additionally (fig. 6), connected to the SCART input on your TV that is provided for S-Video.
Note that only the video plugs (the "yellow" cinch plug in fig. 3 and the S-Video plug in fig.
6) must be connected to the TV Monitor
Output
, and the volume on the TV must be
reduced to minimum.
SCART/Cinch-Adapter for
SCART/Cinch-Adapter for
record and playback;
Cinch/SCART-Adapter for
SCART/S-Video Adapter
SCART/S-Video Adapter
for record and playback;
SCART/S-Video Adapter
Figure 1:
playback;
signal flow:
SCART Cinch
Figure 2:
signal flow:
SCART Cinch
Figure 3:
playback;
signal flow:
Cinch → SCART
Figure 4:
for playback;
signal flow:
SCART Cinch
Figure 5:
signal flow:
SCART Cinch
Figure 6:
for playback;
signal flow:
Cinch → SCART
1
Also other colours possible, e.g. brown and grey.
Important Note for Adapter Cables:
If the cinch connectors of the adapter you’ll use are labeled, connect the Audio and Video ”In” plugs with the corresponding Audio and Video ”In” jacks on the AVR 2000 (and with a VCR connect the ”Out” plugs to the ”Out” jacks on the AVR). Note that with some adapter types it may be just turned around: If no signal is audi­ble/ visible when the VCR is playing connect the “Out” plugs to the ”In” jacks on the AVR and turned around. If the adapter plugs are not labeled in that way,pay attention to the signal flow directions as shown in the diagrams above and in the instruction attached to the adapter. If uncertain, don’t hesitate to consult your dealer.
Black
Yellow
Red
Red
Black
S-Video Out
Black Yellow Red
Black Red
1
Blue Yellow
1
Green White
Red Black
S-Video In
Black Red
1
Blue Yellow
S-Video In S-Video Out
Important Notes for S-Video connections:
1. Only the S-Video In/Out of S-Video devices must be connected to the AVR, NOT both, nor­mal video and S-Video In/Outputs (except the TV, see item 2).
2. Like most common AV units the AVR 2000 does not convert the Video signal to S-Video or vice versa. Thus both connections must be made from the AVR 2000 to the TV if both, Video and S-Video sources, are used, and the appropriate input on the TV must be selected.
INSTALLATION AND CONNECTIONS 15
Installation and Connections
Important Note for the Use of SCART-Cinch Adapters:
When video sources are connected to the TV directly with a SCART cable, specific control sig­nals apart from Audio/Video signals will be fed to the TV.These specific signals are:With all video sources, the signal for automatic input selection that switches the TV automatically to the appropriate input as soon as the video source is started. And with DVD players, the sig­nals automatically turning the TV to 16:9 format (with switchable 4:3 TVs) and turning the RGB video decoder of the TV on or off, depending on the DVD player´s setting. With any adapter cable, these control signals will be lost and the appro­priate setting of the TV must be made manually.
System and Power Connections
The AVR 2000 is designed for flexible use with external control components and power ampli­fiers.
Remote Control Extension
If the receiver is placed behind a solid or smoked glass cabinet door, the obstruction may prevent the remote sensor from receiving commands. In this event, the remote sensor of any Harman Kardon or other compatible device, not covered by the door, or an optional remote sensor may be used. Connect the Remote IR Output of that device or the output of the remote sensor to the Remote IR Input jack
If other components are also prevented from receiving remote commands, only one sensor is needed. Simply use this unit’s sensor or a remote eye by running a connection from the Remote IR Output jack jack on Harman Kardon or other compatible equipment.
NOTE:All remotely controlled components must be linked together in a daisy chain. Connect the IR OUT jack of one unit to the IR IN of the next to establish this chain.
.
to the Remote IR Input
AC Power Connections
This unit is equipped with two accessory AC out­lets.They may be used to power accessory devices, but they should not be used with high­current draw equipment such as power ampli­fiers.The total power draw to the Unswitched Outlet
must not exceed 100 watts, that to
the Switched Outlet The Switched
when the unit is on completely.This is recom­mended for devices that have no power switch or a mechanical power switch that may be left in the “ON” position.
NOTE: Many audio and video products go into a Standby mode when they are used with switched outlets, and cannot be fully turned on using the outlet alone without a remote control command.
The Unswitched as long as the unit is plugged into a powered AC outlet and the Main Power Switch
Finally, when all connections are complete, plug the power cord into a nonswitched 220-240-volt AC wall outlet.You’re almost ready to enjoy the AVR 2000!
50 watts.
outlet will receive power only
outlet will receive power
1
is on.
16 INSTALLATION AND CONNECTIONS
System Configuration
Right Front Speaker
Left Front
Speaker
No more than
60cm
Center Front Speaker
When all audio, video and system connections have been made, there are a few configuration adjustments that must be made.A few minutes spent to correctly configure and calibrate the unit will greatly add to your listening experience.
Speaker Selection
No matter which type or brand of speakers is used, the same model or brand of speaker should be used for the front-left, center and front-right speakers.This creates a seamless front soundstage and eliminates the possibility of distracting sonic disturbances that occur when a sound moves across mismatched front-channel speakers.
Speaker Placement
The placement of speakers in a multichannel home-theater system can have a noticeable impact on the quality of sound reproduced.
Depending on the type of center-channel speaker in use and your viewing device,place the center speaker either directly above or below your TV, or in the center behind a perforated front-projection screen.
Once the center-channel speaker is installed, position the left-front and right-front speakers so that they are as far away from one another as the center-channel speaker is from the preferred listening position. Ideally, the front-channel speakers should be placed so that their tweeters are no more than 60cm above or below the tweeter in the center-channel speaker.
They should also be at least 0.5 meter from your TV set unless the speakers are magnetically shielded to avoid colourings on the TV screen. Note that most speakers are not shielded, even with complete surround sets only the Center speaker may be.
Depending on the specifics of your room acoustics and the type of speakers in use,you may find that imaging is improved by moving the front-left and front-right speakers slightly forward of the center-channel speaker. If possible, adjust all front loudspeakers so that they are aimed at ear height when you are seated in the listening position.
Using these guidelines, you’ll find that it takes some experimentation to find the correct location for the front speakers in your particular installation. Don’t be afraid to move things around until the system sounds correct. Optimize your speakers so that audio transitions across the front of the room sound smooth.
Surround speakers should be placed on the side walls of the room, at or slightly behind the listening position. The center of the speaker should face you.
If side-wall mounting is not practical, the speakers may be placed on a rear wall, behind the listening position. The speakers should be no more than two meters behind the rear of the seating area.
Subwoofers produce largely nondirectional sound, so they may be placed almost anywhere in a room. Actual placement should be based on room size and shape and the type of subwoofer used. One method of finding the optimal location for a subwoofer is to begin by placing it in the front of the room, about 15cm from a wall, or near the front corner of the room. Another method is to temporarily place the subwoofer in the spot where you will normally sit, and then walk around the room until you find a spot where the subwoofer sounds best. Place the subwoofer in that spot. You should also follow the instructions of the subwoofer’s manufacturer, or you may wish to experiment with the best location for a subwoofer in your listening room.
A) Front Channel Speaker Installation with Direct-View TV Sets or Rear-Screen Projectors
TV or Projection Screen
Left Front
Speaker
No more than 2m
speakers are used
when rear-mounted
Center Front
Speaker
Optional Rear-Wall Mounting
Right Front
Speaker
B) The distance between the left and right speakers should be equal to the distance from the seating position to the viewing screen. You may also experiment with placing the left and right speakers slightly forward of the center speaker.
SYSTEM CONFIGURATION 17
System Configuration
First Turn On
Once the speakers have been placed in the room and connected, the remaining steps are to program the system configuration memories. With the AVR 2000 two kind of memories are used, those associated individually with the input selected, e.g.surround modes, and others working independently from any input selected like speaker output levels, or delay times used by the surround sound processor.
You are now ready to power up the AVR 2000 to begin these final adjustments.
1. Plug the Power Cable switched AC outlet.
2. Press the Main Power Switch latches and the word “OFF” on the top of the switch disappears inside the front panel. Note that the Power Indicator indicating that the unit is in the Standby mode.
3. Install the 2 supplied AAA batteries in the remote as shown. Be certain to follow the (+) and (–) polarity indicators as shown in the figure below.
4.Turn the AVR 2000 on either by pressing the
System Power Control Source Selector
the remote by pressing the AVR Selector or any of the Input Selectors remote.The Power Indicator to confirm that the unit is on, and the Main
Information Display
into an un-
1
3
will turn amber,
2
or the Input
!
on the front panel, or via
46
3
will turn green
Ú
will also light up.
in until it
5
on the
Settings to be Made With Each Input Used
The AVR 2000 features an advanced memory system that enables you to establish different configurations for the speaker configuration,dig­ital input and surround mode for each input source.This flexibility enables you to custom tai­lor the way in which you listen to each source and have the AVR 2000 memorize them. This means, for example, that you may associate dif­ferent surround modes and analog or digital inputs with different sources, or set different speaker configurations with the resultant changes to the bass management system or the use of the Center speaker. Once these settings are made, they will automatically be recalled whenever you select an input.
The default settings for the AVR 2000, as it is shipped from the factory, have all inputs set for an analog source, with stereo as the surround mode, the front left and right speakers set to “large” (with surround modes other speakers to ”small”), and a subwoofer connected. Before using the unit, you will probably want to change these settings for most inputs so that they are properly configured to reflect the use of digital or analog inputs, the type of speakers installed and the surround mode specifics. Remember, since the AVR 2000’s memory system keeps the settings for each input separate from the other inputs, you will need to make these adjustments for each input used. However, once they are made, further adjustment is only required when system components are changed.
To make this process as quick and as easy as possible, we suggest that with each of these set­tings to be made you step through each input. Once you have completed the settings for the first input, many settings may be duplicated for the remaining inputs.
The items that follow will describe the individual settings required for each input.
Input Setup
The first step in configuring the AVR 2000 is to select an input. This may be done by pressing the front panel Input Source Selector until the desired input’s name appears momen­tarily in the Main Information Display and the green LED lights next to the input’s name in the front panel Input Indicators The input may also be selected by pressing the appropriate Input Selector on the remote control
46
.
The second step is to associate one of the digital inputs with the selected input source (if this is needed, otherwise the selected analog input will remain). Press the Digital Input Select button
ÒFon the front panel or the remote.Within
five seconds, make your input selection using the Selector buttons on the front panel
/¤ buttons
desired digital or analog input is shown in the
Main Information Display Set button
assignment. After the setting has been made with one input, repeat as described above with all inputs in use.The digital input associated with the input selected can also be changed at any time later and the AVR 2000´s memory sys­tem will keep the settings until they are changed again.
Speaker Setup
This setup tells the AVR 2000 which type of speakers are in use.This is important as it adjusts the settings that determine which speakers receive low frequency (bass) informa­tion and whether a Center speaker should be used or not, separately for each input used. For each of these settings use the LARGE set­ting if the speakers for a particular position are traditional full-range loudspeakers that are capable of reproducing sounds below 100Hz. Use the SMALL setting for smaller, frequen­cy-limited satellite speakers that do not repro­duce sounds below 100Hz. Note that when “small” front (left and right) speakers are used, a subwoofer is required to reproduce low fre­quency sounds. If you are in doubt as to which category describes your speakers,consult the specifications in the speakers’ owner’s manual, or ask your dealer. Remember that each speaker setup that differs from the default settings (see above) must be made individually for each input of the AVR 2000.
It is best to select the Dolby Pro Logic mode for speaker setup.Then with the currently selected input all settings will be copied to other surround modes too (as far as possible) and need not be repeated with any other mode.
C
on the remote until the
X
E
to enter the new digital input
!
X
,
Ô
5
or the
. Then press the
.
18 SYSTEM CONFIGURATION
System Configuration
With the AVR 2000 turned on, follow these steps to configure the speakers:
1. Put the AVR 2000 in the Dolby Pro Logic
mode by pressing the Surround Mode Selector button then the
7
/¤ buttons
on the front or 9and
C
on the remote, until
PRO LOGICappears in the Main Information Display
indicator
F
lights.
2. Press the Speaker button
X
and the PRO LOGIC
Ùon the
remote or front panel. The words FRNT SPEAKER will appear in the Main
Information Display
3. Press the Set button
4. Press the
/¤ buttons
the Selector buttons
X
.
EÓ.
C
on the remote or
5
on the front panel until either LARGE or SMALL appears, matching the type of speakers you have at the left-front and right-front positions, as described by the definitions shown in preceding section.
When SMALL is selected, low frequency front channel sounds will be sent only to the subwoofer output. Note that if you choose this option and there is no subwoofer connected, you will not hear any low frequency sounds from the front channels.
When LARGE is selected, a full-range output will be sent to the front left and front right out­puts. Depending on the subwoofer configuration (see below), the front left and right bass informa­tion may also be directed to a subwoofer.
Important Note: When a speaker set with two front satellites and a passive subwoofer is used, connected to the front speaker outputs
,
the fronts must be set for LARGE.
5.When you have completed your selection for the front channels, press the Set button and then press the
/¤ buttons
remote or the Selector buttons
C
5
on the front
EÓ,
on the
panel to change the display to CEN SPEAKER.
6. Press the Set button the
/¤ buttons
Selector buttons
EÓagain, and use
C
on the remote, or the
5
on the front panel, to select the option that best describes your system based on the Center speaker definitions shown in preceding section.
When SMALL is selected, low frequency cen­ter channel sounds will be sent to the Fronts, if they are set for LARGE and Sub is turned off. When Sub is on, low frequency center channel sounds will be sent to the subwoofer only.
When LARGE is selected, a full-range output will be sent to the center speaker output, and with analog and digital surround modes NO cen­ter channel signal will be sent to the subwoofer output.
When NONE is selected, no signal will be sent to the center channel output. The receiver will operate in a “phantom” center channel mode and center channel information will be sent to the left and right front channel outputs.This mode is needed if no Center speaker is used (note that for the use of Logic 7C surround mode a Center speaker is needed, but Logic 7M works well without a Center too).
7. When you have completed your selection for the center channel, press the Set button
Ó
, and then press the ⁄/¤ buttons Con
the remote or the Selector buttons
5
E
on the front panel to change the display to SUR SPEAKER.
8. Press the Set button use the
/¤ buttons
Selector buttons
EÓagain, and then
C
on the remote or the
5
on the front panel to select the option that best describes your system based on the Surround speaker definitions shown in preceding section.
When SMALL is selected, low frequency sur­round channel sounds will be sent to the Fronts, when Sub is turned off,or to the subwoofer out­put when Sub is on. With Pro Logic mode, there is no bass in the surround channels.
When LARGE is selected, a full-range output will be sent to the surround channel outputs (with all analog and digital surround modes), and, except with Hall and Theater modes, NO surround channel bass will be sent to the sub­woofer output.
When NONE is selected, surround sound information will be split between the front-left and front-right outputs. Note that for optimal performance when no surround speakers are in use, the Dolby 3 Stereo mode should be used instead of Dolby Pro Logic.
9. When you have completed your selection for the surround channel, press the Set button
Ó
, and then press the ⁄/¤ buttons Con the
remote or the Selector buttons
5
E
on the front panel to change the display to S-W SPEAK- ER.
10. Press the Set button press the
/¤ buttons
the Selector buttons
EÓ, and then
C
on the remote or
5
on the front panel to select the option that best describes your Subwoofer system.
The choices available for the subwoofer position will depend on the settings for the other speak­ers, particularly the front left/right positions.
If the front left/right speakers are set to SMALL, the subwoofer will automatically be set to SUB, which is the “on” position.
If the front left/right speakers are set to LARGE, three options are available:
• If no subwoofer is connected to the AVR 2000, press the arrow buttons
C5so that
NONE appears in the display.When this option is selected, all bass information will be routed to the front left/right “main” speakers.
• If a subwoofer is connected to the AVR 2000, you have the option to have the front left/right “main” speakers reproduce bass frequencies at all times, and have the subwoofer operate only when the AVR 2000 is being used with a digital source that contains a dedicated Low Frequency Effects, or LFE soundtrack. This allows you to use both your main and subwoofer speakers to take advantage of the special bass created for certain movies.To select that option press the arrow buttons
C5so that SUB(LFE) appears
in the display.
• If a subwoofer is connected and you wish to use it for bass reproduction in conjunction with the main front left/right speakers,regardless of the type of program source or surround mode you are listening to, press the arrow buttons
C5so that SUB L/R+LFE appears in
the display.When this option is selected, a “complete” feed will be sent to the front left/right “main” speakers, and the subwoofer will receive the front left and right bass frequen­cies.
11. When all speaker selections have been made for the input selected, press the Set button
Ó
twice or simply wait for three seconds until
E
the display returns to the normal mode.
SYSTEM CONFIGURATION 19
System Configuration
To assist in making these settings,the icons in the Speaker/Channel Input Indicators will change as the speaker type is selected at each position. When only the inner icon box is lit, the speaker is set for “small.” When the inner box and the two outer boxes with circles inside them are lit, the speaker is set for “large." When no indicator appears at a speaker location, that position is set for “none” or “no” speaker.
As an example, in Figure 6 below, the left front and right front speakers are set for “large,” the center, left surround and right surround speakers are set for small, and a subwoofer is set.
After the speaker setting has been made with one input, repeat as described above with all inputs you will use. In most cases, the speaker type will be the same and may be quickly entered by entering the same data used for the original input. But with some music sources you may pre­fer to listen to your surround system without using a Center speaker, particularily when a small Center is in use with an audio performance not matching perfectly with the main front speakers. With these sources selected the Center speaker may be turned off automatically (enter NONE for the Center setting), while its signal will be fed to the left and right Fronts.
The speaker setting mode can also be changed at any time later, and the AVR 2000´s memory sys­tem will keep these settings for the input select­ed, until they are changed again.
P
LR
Figure 6
Surround Setup
Once the speaker setup has been completed, the next setup step is to set the surround mode you wish to use with each input. Since surround modes are a matter of personal taste, feel free to select any mode you wish – you may change it later. The Surround Mode chart on page 24 may help you select the mode best suited to the input source selected. However, to make it easier to establish the initial parameters for the AVR 2000, it is best to select Dolby Pro Logic for most ana­log inputs and Dolby Digital for inputs connected to digital sources. In the case of inputs such as a CD Player, Tape Deck or Tuner, you may wish to set the mode to Stereo, if that is your preferred listening mode for standard stereo sources, where it is unlikely that sur al will be used. Alternatively, the 5 Channel Stereo or
Logic 7 Music mode may also be a good
choice for stereo-only source material.
To set the surround mode you wish to use with the input selected, press the Surround Mode Selector button
/¤ buttons
desired surround mode´s name appears in the
Main Information Display
As the modes are changed, a green LED will also light next to the mode names in the Surround
Mode Indicators
Note that Dolby Digital and DTS will only appear as choices when a digital input has been select­ed.
After the surround mode setting has been made with the current input, repeat the setting with all inputs you will use.The surround mode can also be changed at any time later, and the AVR 2000´s memory system will keep the settings for the input selected, until they are changed again.
7
C
round encoded materi-
on the front or 9and the
on the remote until the
X
.
ˆ
on the front panel.
Making Settings independent of selected Input
After the settings described above have been made for all input sources in your system, the following settings, made with any input,will remain in effect independent of the input selected.
Delay Settings
Only for the Dolby Digital or Dolby Pro Logic modes, you will need to adjust the delay time setting. Note that the delay time is not adjustable for any other modes.
Important Note: Once the delay time is set with any input it will be effective with all other inputs too. Moreover the surround delay time setting must be made only for either the Dolby Pro Logic or the Dolby Digital mode.The other setting will be set automatically.
Due to the different distances between the lis­tening position for the front channel speakers and the surround speakers,the amount of time it takes for sound to reach your ears from the front or surround speakers is different.You may com­pensate for this difference through the use of the delay settings to adjust the timing for the specific speaker placement and acoustic conditions in your listening room or home theater.
The factory setting (see Surround Mode Chart page 24) is appropriate for most rooms, but some installations create an uncommon distance between the front and surround speakers that may cause the arrival of front channel sounds to become disconnected from surround channel sounds.
To resynchronize the front and surround chan­nels, follow these steps:
1. Measure the distance from the listening/ view­ing position to the front speakers in meters.
2. Measure the distance from the listening/ view­ing position to the surround speakers.
3. Subtract the distance to the surround speakers from the distance to the front speakers and multiply the result by 3.
a.When setting the delay time for the Dolby
Digital surround modes, the optimal delay time is the result of that subtraction. For example, if the front speakers are 3 m away and the sur­round speakers are 1 m away, the optimal delay time is figured as (3–1)x3=6. Thus,in this example, the delay time for Dolby Digital should be set at six milliseconds.
b.When setting the delay time for the Pro Logic
mode, take the result of the subtraction and add 15 to obtain the optimal delay time. For example, if the front speakers are 3 m away and the surround speakers are 1 m away, the optimal delay time is figured as
20 SYSTEM CONFIGURATION
System Configuration
(3–1)x3+15=21.Thus, in this example, the Pro Logic delay should be set at twenty millisec­onds.
NOTE: The DTS, Logic 7, 5CH Stereo,Hall and Theater modes use a fixed, nonadjustable delay time.
The Dolby Digital Mode also includes a separate setting for the center channel delay mode, since the discrete nature of these signals makes the location of the center channel speaker more criti­cal. To calculate the delay for the center channel, measure the distance from the preferred listening position in the center of the room to both the center channel speaker and either the left or right speaker.
If the distances are equal, no further adjustment is required and the center delay should be set to zero. If the distance to the front speakers is greater than the distance to the center speaker, you may wish to reposition the speakers by mov­ing the front left and front right speakers closer to the listening position or the center speaker further away from the listening position.
If repositioning of the speakers is not possible, adjust the center delay time, adding one milli­second of center channel delay for every 30 cm closer to the listening position the center speaker is than the front speakers.For example, if the front left and front right speakers are each 3 m from the listening position and the center chan­nel speaker is 2.4 m away, the delay is figured as 300 cm –240 cm=60 cm, suggesting an optimal center delay of 2 milliseconds.
To set the delay time,follow these steps:
1. To make the delay settings for the Dolby Digital mode (this will include the Center delay setting, and the surround delay for the Pro Logic mode will be set automatically), press the Input
Source Selector
!
on the front or 4on the remote and select any input now that is associat­ed with a digital input and the Dolby Digital sur­round mode (the surround mode associated with each input selected will be indicated by the
Surround Mode Indicators
ˆ
in the front
panel).
2. Press the Delay button
on the remote
or front panel. The words S DELAY TIME appear in the Main Information Display
3. Press the Set button
4. Press the
/¤ buttons
the Selector buttons
EÓ.
C
on the remote or
5
on the front panel until
X
.
the desired rear delay time for the Dolby Digital mode, calculated using the formula for Dolby Digital above (item a.), appears in the display.
5. Press the Set button
EÓto enter the
setting into the AVR2000’s memory.
6. Press the ⁄/¤ buttons Con the remote once, so that CDELAY TIME appears in the
Main Information Display
7. Press the Set button
8. Press the
/¤ buttons
X
EÓ.
C
.
on the remote until the desired delay time for the center chan­nel appears in the display.
9. Press the Set button
EÓto enter the set-
ting into the AVR 2000’s memory.
You have now completed the delay time settings for all surround modes and inputs.
Night Mode Settings
The Night mode is a feature of Dolby Digital that uses special processing to preserve the dynamic range and full intelligibility of a movie sound track while reducing the peak level.This prevents abruptly loud transitions from disturbing others, without reducing the sonic impact of a digital source. Note that the Night mode is only avail­able when the Dolby Digital surround mode is selected.
To adjust the Night mode setting press the Input
Source Selector
!
on the front or 4on the remote and select an input that is associated with a digital input and the Dolby Digital sur­round mode.
Next press the Night button
A
on the remote.
When the button is pressed, the words
D-RANGE will appear in the Main Information Display X. Press the
/¤
buttons Cwithin three seconds to select the desired setting:
OFF: When OFF is shown in the display, the Night mode will not function.
MID: When MID is shown in the display, a mild compression will be applied.
MAX:When MAX is shown in the display,a more severe compression algorithm will be applied.
When you want to use the Night mode feature, we recommend that you select the MID setting as a starting point and change to the MAX setting later, if desired.
When any Night mode is selected, the NIGHT
Mode Indicator the selection press the Set button
N
will illuminate.To confirm
EÓor
wait for some seconds until the display returns to the normal mode.
Output Level Adjustment
Output level adjustment is a key part of the con­figuration process for any surround sound prod­uct. It is particularly important for a Dolby Digital receiver such as the AVR 2000, as correct outputs will ensure that you hear sound tracks with the proper directionality and intensity.
NOTE: Listeners are often confused about the operation of the surround channels.While some assume that sound should always be coming from each speaker, most of the time there will be little or no sound in the surround channels.This is because they are only used when a movie director or sound mixer specifically places sound there to create ambiance, a special effect or to continue action from the front of the room to the rear. When the output levels are properly set it is normal for surround speakers to operate only occasionally.Artificially increasing the vol­ume to the rear speakers may destroy the illu­sion of an enveloping sound field that dupli­cates the way you hear sound in a movie the­ater or concert hall.
IMPORTANT NOTE: The output level can be adjusted for each digital and analog surround mode separately.This allows you to compensate for level differences between speakers,that may also vary with the surround mode selected, or to increase or decrease the level of certain speakers intentionally, depending on the surround mode selected.
Before beginning the output level adjustment process, make certain that all speaker connec­tions have been properly made.The system volume should be turned down at first. Finally, make certain that the Balance Control
&
is
set to the center “12 o’clock” position.
To adjust and calibrate the output levels, follow these steps. For accurate calibration, it is a good idea to make these adjustments while seated in your favorite listening position. As the adjust­ment must be made for each surround mode, it is best to select any input associated with Dolby Pro Logic, make the adjustment for that surround mode, then step through all inputs you´re using (and thus through all surround modes associated with the inputs) and repeat the adjustment when any surround mode appears that has not yet been adjusted.
1. Select any input associated with the Dolby Pro Logic surround mode by pressing the Input
Source Selector Surround Mode Indicator
and
F
in the display light up.
2. Press the Test Tone button
!4until the Pro Logic
ˆ
on the front
7ıon the
remote.The words T-T FL 0dBwill appear in the Main Information Display
X
.
SYSTEM CONFIGURATION 21
System Configuration
3. The test noise will immediately begin to circu­late in the speakers in a clockwise rotation, pausing at each position for two seconds.As the test noise rotates the speaker positions FL, C, FR, RS, LS(Front Left,Center, Front Right, Right Surround, Left Surround) will be shown in the Main Information Display
X
. As an added assist, while the test noise is circulating, the proper channel position will also be indicat­ed in the Speaker/Channel Indicators
P
by a blinking letter within the correct channel. Turn up the volume now until you can hear the noise clearly.
IMPORTANT NOTE: Because this test noise will have a much lower level than normal music, the volume must be lowered after the adjustment for all channels is made, but BEFORE you turn the test tone off.
NOTE:This is a good time to verify that the speakers have been properly connected.As the test noise circulates, listen to make certain that the sound comes from the speaker position shown in the Main Information Display. If the sound from a speaker location does NOT match the position indicated in the display, turn the AVR 2000 off using the Main Power Switch 1 and check the speaker wiring to make cer­tain that each speaker is connected to the cor­rect output terminal.
After checking for speaker placement, let the test noise circulate again, and listen to see which channels sound louder than the others. Using the front left speaker as a reference,press the
/¤ buttons
C
on the remote to bring all speakers to the same volume level. Note that when one of the
/¤ buttons is pushed,the
test noise circulation will pause on the channel being adjusted to give you time to make the adjustment.When you release the button, the cir­culation will resume after five seconds.
Continue to adjust the individual speakers until they all have the same volume. Note that adjust­ments should be made with the
C
on the remote only, NOT the main volume
/¤ buttons
controls. NOTE: The subwoofer output level is not
adjustable using the test tone.To change the subwoofer level, follow the steps for Output Level Trim Adjustment on page 28.
When all channels have the same output level, turn the Volume
("down to about -40dB,
otherwise the listening level may be too high as soon as the source’s music starts to play. After­wards press the Test Tone Selector
ı
7
button again to turn the test tone off and com­plete the process.
IMPORTANT NOTE: The Output level adjust­ment made will be effective for the surround mode currently selected, also when other inputs are selected using the same surround mode.To adjust the output level with all other surround modes used, step through all inputs you´re using by pressing the Source Selector buttons
!
on the front panel or the appropriate Input
Selectors
4
on the remote.When the indica­tor for any surround mode for which the level adjustment has not yet been made lights in the
Main Information Display
X
or its green
LED lights in the Surround Mode Indicators field
ˆ
, repeat the level adjustment described above.This will also allow you to compensate level differences between speakers,that may be different with each surround mode, or to increase or decrease the level of certain speakers intentionally, depending on the surround mode selected.
Note: Output level adjustment is not available for the VMAx or Surround Off mode, as no sur­round speakers are used (so level differences between the speakers in the room cannot occur). But to compensate level differences between stereo,VMAx and other surround modes (independently from the input selected) the outputs can be adjusted with the Level Trim Adjustment procedure, see page 28,also for the Surround Off (Stereo) and VMAx modes.
Once the settings outlined on the previous pages have been made, the AVR 2000 is ready for operation.While there are some additional settings to be made, these are best done after you have had an opportunity to listen to a variety of sources and different kinds of program material. These advanced settings are described on page 28 of this manual. In addition, any of the settings made in the initial configuration of the unit may be changed at any time. As you add new or different sources or speakers, or if you wish to change a setting to better reflect your listening taste, simply follow the instructions for changing the settings for that parameter as shown above. Note that any settings changed at any time, will be stored in memory in the AVR 2000, also if it´s turned off completely, unless it will be reset (see page 46). The settings will either depend on the input (Speaker configuration, analog/digital input selection, surround mode) or on the surround mode selected (speaker output level), as described on previous pages. Having completed the setup and configuration process for your AVR 2000, you are about to experience the finest in music and home theater listening. Enjoy!
22 SYSTEM CONFIGURATION
Operation
90
min80min70min60min50min
40
min
30
min20min10min
OFF
Basic Operation
Once you have completed the setup and configu­ration of the AVR 2000, it is simple to operate and enjoy.The following instructions should be followed for you to maximize your enjoyment of your new receiver:
Turning the AVR 2000 On or Off
• When using the AVR 2000 for the first time, you must press the Main Power Switch front panel to turn the unit on.This places the unit in a Standby mode, as indicated by the amber color of the Power Indicator is in Standby,you may begin a listening session by pressing the System Power Control
Source button Selector
3
will turn green.This will turn the unit on and
!
on the front panel or the AVR
5
. Note that the Power Indicator
return it to the input source that was last used. The unit may also be turned on from Standby by pressing any of the Source Selector buttons on the remote
46
.
NOTE: After pressing one of the Input Selector buttons
4
(except VID4) to turn the unit on,
press the AVR Selector
5
control the AVR functions.
To turn the unit off at the end of a listening ses­sion, simply press the System Power Control
2
on the front panel or the Power Off
Button
3
on the remote. Power will be shut
off to any equipment plugged into the rear panel
Switched AC Outlets Indicator
3
will turn amber.
When the remote is used to turn the unit “off”it is actually placing the system in a Standby mode, as indicated by the amber color of the Power
Indicator
3
.
When you will be away from home for an extended period of time it is always a good idea to completely turn the unit off with the front panel Main Power Switch
NOTE:All preset memories may be lost if the unit is left turned off with the Main Power
Switch
1
for more than two weeks.
Using the Sleep Timer
• To program the AVR 2000 for automatic turn­off,press the Sleep Button Each press of the button will increase the time before shut down in the following sequence:
1
on the
3
. Once the unit
2
or the
to have the remote
and the Power
1
.
8
on the remote.
The sleep time will be displayed in the Preset
Number/Sleep Timer Indicator
Q
and it will
count down until the time has elapsed.
When the programmed sleep time has elapsed, the unit will automatically turn off (to Standby mode). Note that the front panel display will dim to one half brightness when the Sleep function is programmed.To cancel the Sleep function, press and hold the Sleep Button
8
until the information display returns to normal brightness and the Sleep indicator numbers disappear and the words SLEEP OFF appear in the
Main Information Display
X
.
Source Selection
• To select a source, press any of the Source Selector buttons on the remote
NOTE: After pressing one of the Input Selector
buttons
4
(except VID4) to turn the unit on,
press the AVR Selector control the AVR functions.
• The input source may also be changed by pressing the front-panel Input Source Selector button
!
. Each press of the button will move the input selection through the list of available inputs.
• As the input is changed, the AVR 2000 will automatically switch to the digital input (if selected), surround mode and speaker configura­tion that were entered during the configuration process for that source.
• The front-panel Video 4 Inputs used to connect a device such as a video game or camcorder to your home entertainment system on a temporary basis.
• When the input source is changed, the new input name will appear in the Main
Information Display
X
light next to the selected input’s name in the front-panel Input Indicators
• When a pure audio source (Tuner,CD,Tape, 6 Channel direct inputs) is selected, the last video input used remains routed to the Video 1 and
Video 2 Outputs

Video 1/ source) and Video Monitor Output
. This permits simultaneous viewing and lis-
tening to different sources.
• When a Video source is selected, its audio sig­nal will be fed to the speakers and the video sig­nal for that input will be routed to the appropriate Monitor Output jack
on a TV monitor connected to the AVR 2000.
46
.
5
to have the remote
%
may be
and a green LED will
Ô
.
(except from its own
and will be viewable
Controls and Use of Headphones
• Adjust the volume to a comfortable level using the front panel Volume Control
Volume Up/Down
• The Balance Control
"
&
adjust the relative sound output between the left front and right front speakers.
• To temporarily silence all speaker outputs press the Mute button
the output to all speakers and the headphone jack, but it will not affect any recording or dub­bing that may be in progress.When the system is muted, the MUTE indicator the Main Information Display Mute button
again to return to normal
operation.
• During a listening session you may wish to adjust the Bass Control
Control
*
to suit your listening tastes or room
acoustics.
• To set the output of the AVR 2000 so that the output is “flat,” with the Tone controls and the Balance control de-activated, press the Tone Mode button
6
button once or twice so that
the words Tone Out appear momentarily in the Main Information Display return the tone controls to an active condition, press the Tone Mode
6
so that the words Tone In momentarily appear in the Main Information Display
• For private listening, plug the 6.3 mm stereo phone plug from a pair of stereo headphones into the front panel Headphone Jack that when the headphone’s plug is connected, the word HEADPHONE will scroll once across the Main Information Display all speakers will be silenced.When the head­phone plug is removed, the audio feed to the speakers will be restored.
(
or remote
buttons.
may be used to
. This will interrupt
O
will light in
Ú
. Press the
^
and Treble
X
.To
button once or twice
4
X
X
. Note
and
.
OPERATION 23
Operation
Surround Mode Chart
MODE FEATURES DELAY TIME RANGE
DOLBY DIGITAL Available only with digital input sources encoded with Dolby Digital data. It provides Center: 0 ms – 5 ms
up to five separate main audio channels and a special dedicated Low Frequency Effects Initial Setting – 0 ms channel. Surround: 0 ms –15 ms
Initial Setting – 0 ms
DTS Available only with digital input sources encoded with DTS data.Available on special Delay time not adjustable
DVD, LD and audio-only discs, DTS provides up to five separate main audio channels and a special dedicated low frequency channel.
DOLBY PRO LOGIC The standard mode for analog surround sound decoding. It uses information encoded 15 ms – 30 ms
in a two channel stereo recording to produce four distinct outputs: Left, Center, Right and Initial Setting = 15 ms a Mono Surround channel. Use this mode for accurate reproduction of programs bearing the Dolby Surround, DTS Stereo,UltraStereo or other “Surround”logos. Surround-encoded programs include videocassette, DVD and LD movies,TV and cable programs, radio programs and audio CDs. Dolby Pro Logic processing may also be used to provide a pleasing surround effect with some stereophonic source material that does not carry surround encoding.
LOGIC 7 C LOGIC 7 M
DOLBY 3 STEREO Uses the information contained in a surround encoded or two channel stereo program to No surround channels
THEATER This surround processing uses matrix surround decoding to simulate a standard movie or Delay time not adjustable
HALL The Hall mode offers matrix surround decoding that simulate Delay time not adjustable
VMAx Near When only the two front channel loudspeakers are used, Harman’s patented VMAx mode No surround channels VMAx Far delivers a three-dimensional sound space with the illusion of “phantom speakers”at the
An advanced mode that extracts the maximum surround information from either conventional stereo material or surround-encoded programs.When used with encoded material, decoding is more accurate in terms of the placement of sounds, and fades and pans are much smoother and more realistic than with other decoding techniques. Logic 7 also delivers increased spaciousness and a wider sound stage when it is used with conventional natural stereo recordings and music programs throug the use of the natural surround information present also in those stereo recordings.The Logic 7C or Cinema mode is tailored to provide an optimal sound field for movie soundtracks.The Logic 7M or Music mode uses a decoding formula that is best suited to music.
create center channel information. In addition, the information that is normally sent to the rear channel surround speakers is carefully mixed in with the front left and front right channels for increased realism. Use this mode when you have a center channel speaker but no surround speakers.
stage theater with stereo and even pure mono sources.
a medium-sized chamber hall or opera house with stereo and even pure mono sources.
center and surround positions.The VMAx N, or “Near Field” mode should be selected when your listening position is less than 1,5m from the speakers.The VMAx F, or “Far Field” mode should be selected when your listening positioin is greater than 1,5m from the speakers.
Delay time not adjustable
5-Channel Stereo This mode takes advantage of multiple speakers to place a stereo signal at both the front and No delay is available for
back of a room. Ideal for playing music in situations such as a party, it places the same signal this mode at the front-left and surround-left, and at the front-right and surround-right speakers. The center channel is fed a summed mono mix of the in-phase material of the left and right channels.
SURROUND This mode turns off all surround processing and presents the pure left and right No surround channels OFF (STEREO) channel presentation of two channel stereo programs.
24 OPERATION
Operation
Surround Mode Selection
One of the most important features of the AVR 2000 is its ability to reproduce a full multi­channel surround sound field from digital sources, analog matrix surround encoded pro­grams and standard stereo or even mono pro­grams. In all, a total of thirteen listening modes are available on the AVR 2000.
Selection of a surround mode is based on personal taste, as well as the type of program source mate­rial being used. For example, motion pictures or TV programs bearing the logo of one of the major surround encoding processes, such as Dolby Surround, DTS Stereo or UltraStereo played in either the Dolby 3 Stereo or Dolby Pro Logic surround modes depending on the source material and speakers in use.
However to create wider, enveloping sound field environments and more defined pans and fly­overs with all analog stereo and surround record­ings select Harman Kardon’s exclusive Logic 7 mode, that creates a stereophonic left and right rear signal, just as recorded in real life (e.g. sound being recorded from left rear side will be heard from that side only) for a dramatic improvement in comparison to Dolby Pro Logic.
NOTE: Once a program has been encoded with matrix surround information, it retains the sur­round information as long as the program is broadcast in stereo.Thus, movies with surround sound may be decoded via any of the analog sur­round modes such as Pro Logic or Logic 7, when they are broadcast via conventional TV stations, cable, pay TV and satellite transmission. In addi­tion, a growing number of made-for-television programs,sports broadcasts, radio dramas and music CDs are also recorded in surround sound. You may view a list of these programs at the Dolby Laboratories Web site at www.dolby.com.
Even when a program is not listed as carrying intentional surround information, you may find that the Pro Logic, Dolby 3 Stereo or Logic 7 modes often deliver enveloping surround presen­tations through the use of the natural surround information present in all stereo recordings. However, for stereo programs without any sur­round information the Theater, Hall and 5CH Stereo modes should be tried (5CH Stereo is effec­tive particularly with old ”extreme” stereo record­ings) and for mono programs,we suggest that you try the Theater or Hall modes. And when you use only two front channel speakers you should select Harman’s patented VMAx mode, delivering a virtu­ally three dimensional sound space with two speakers only.
Surround modes are selected using either the front panel controls or the remote.To select a surround mode from the front panel, press the
Surround Mode Selector
the list of available modes.To select a surround
††
should be
7
to scroll through
mode using the remote, press the Surround
Mode Selector
9
, and then press the
⁄/¤
buttons Cto change the mode.As you press the buttons, the Surround mode name will appear in the Main Information Display
X
and an individual mode indicator will also light up
C D F H I J K L M
. As the sur-
round modes change, a green LED will light next to the current mode in the Surround Mode Indicators list
ˆ
on the front panel.
Note that any time a surround mode is changed it remains associated with the input just selected until another choice is made.
Note that the Dolby Digital or DTS modes may only be selected when a digital input is in use. In addition, when a digital source is present, the AVR 2000 will automatically select and switch to the correct mode (Dolby Digital or DTS), regard­less of the mode that has been previously select­ed. For more information on selecting digital sources, see the following section of this manual.
To listen to a program in traditional two channel stereo, using the front left and front right speak­ers only (plus the subwoofer if installed and con­figured), follow the instructions shown above for using the remote until SURR OFFappears in the Main Information Display
X
.
Digital Audio Playback
Digital audio is a major advancement over past systems such as Dolby Pro Logic. It delivers five dis­crete channels: left front, center, right front, left sur­round and right surround. Each channel reproduces full frequency range (20Hz to 20kHz) and offers dramatically improved dynamic range and signifi­cant improvements to signal-to-noise ratios.In addition, digital systems have the capability to deliver an additional channel that is specifically devoted to low frequency information.This is the “.1” channel referred to when you see these sys­tems descibed as “5.1”.The bass channel is sepa­rate from the other channels,but since it is inten­tionally bandwidth limited, sound designers have given it that unique designation.
Dolby Digital
Dolby Digital (originally known as AC-3 a standard part of DVD, and is available on specially encoded LD discs and satellite broadcasts and it is a part of the new high-definition television (HDTV) system.
Note that an optional, external RF demodulator is required to use the AVR 2000 to listen to the Dolby Digital sound tracks available on laser discs. Connect the RF output of the LD player to the demodulator and then connect the digital output of the demodulator to the Optical or Coaxial inputs
#$
No demodulator is required for use with DVD players or DTS-encoded laser discs.
®
) is
of the AVR 2000.
DTS
DTS is another digital audio system that is capa­ble of delivering 5.1 audio.Although both DTS and Dolby Digital are digital, they use different methods of encoding the signals, and thus they
,
require different decoding circuits to convert the digital signals back to analog.
DTS-encoded sound tracks are available on select DVD and LD discs, as well as on special audio­only DTS CDs.You may use any LD, DVD or CD player equipped with a digital output to play DTS-encoded special audio-only CDs with the AVR 2000, but DTS-LDs can be played on LD players and DTS-DVDs on DVD players only.All that is required is to connect the player’s output to either the Optical or Coaxial input on the rear panel

or front panel
#$
In order to listen to DVDs encoded with DTS sound tracks, the DVD player must be compatible with the DTS signal as indicated by a DTS logo on the player’s front panel. Note that early DVD players may not be able to play DTS- encoded DVDs.This does not indicate a problem with the AVR 2000, as some players cannot pass the DTS signal through to the digital outputs. If you are in doubt as to the capability of your DVD player to handle DTS DVDs, consult the player’s owner’s manual.
PCM Audio Playback
PCM (Pulse Code Modulation) is the non- com­pressed digital audio system used for compact discs, Non-Dolby Digital/DTS Laserdiscs and some special PCM encoded DVDs.The digital circuits in the AVR 2000 are capable of high quality digital­to-analog decoding, and they may be connected directly to the digital audio output of your CD/DVD or LD player (LD only for PCM or DTS programs, for Dolby Digital laser discs an RF adapter is needed, see ”Dolby Digital” above).
Connections may be made to either the Optical or Coaxial inputs front panel Digital Inputs

on the rear panel or the
#$
To listen to a PCM digital source,first select the input for the desired source (e.g., CD) to feed its video signal (if any) to the TV monitor and to provide its analog audio signal for recording. Next press the Digital Select button and then use the remote, or the Selector buttons
⁄/¤
buttons Con the
5
panel, until the desired choice appears in the
Main Information Display Set button
ÓEto confirm the choice.
X
, then press the
When a PCM source is playing, the PCM indica­tor
A
will light. During PCM playback you may select any surround mode except Dolby Digital or DTS.
Playback from PCM sources may also benefit from the Logic 7. When playing a stereo or sur­round-encoded PCM source, such as an LD or CD
.
.
Ò
on the front
F
OPERATION 25
Operation
or a PCM audio track from DVD, use the Logic 7 C or Cinema mode. For stereo or surround encod­ed pure music recordings use the Logic 7 M or Music mode for a wider front sound stage (see Surround Mode Chart page 24).
MP3 Audio Playback
The AVR 2000 is one of the first A/V receivers to provide on-board decoding for the MP3 audio format used on specific computer audio files and by portable MP3 players/recorders. In addition, some new CD and DVD players are capable of playing back optical discs that are recorded with MP3, rather than standard CD audio information. By offering MP3 decoding, the AVR 2000 is able to deliver more precise conversion of the digital signals to an analog output, along with the ben­efits of listening to the MP3 audio through the AVR 2000’s high current amplifier and the speak­ers from your surround system, rather than the smaller speakers and low powered amplifiers typ­ically used with computers.
To take advantage of the AVR 2000’s MP3 capa­bilities, simply connect the PCM output of a com­puter sound card able to feed the MP3 format to its digital output, or the PCM output of MP3 compatible CD or DVD players or of a portable MP3 player with a digital output, to either the rear panel Digital Inputs panel Digital Inputs MP3 signal is selected, the MP3 Bitstream
Indicator
playing.
NOTES:
• The AVR 2000 is only capable of playing sig­nals in the MP3 (MPEG 1/Layer 3) format. It is not compatible with other computer audio codecs.
• The MP 3 DSP mode found in the new AVR 2000 requires an MP3 SPDIF stream. Presently, only a few units provide this but in the coming generations of motherboards and operat­ing system updates this will follow, since SPDIF is the standard for audio & video hardware.
• The digital audio input signal may be either optical or coaxial, but the signal must be in the PCM format. Direct connection of USB or serial data outputs is not possible, even though the sig­nals are in the MP3 format. If you have any ques­tions about the data output format from your computer or a sound card, check with the device’s Owner’s Manual or contact the manu­facturer’s technical support area.
Selecting a Digital Source
To utilize either digital mode you must have properly connected a digital source to the AVR
2000. Connect the digital outputs from DVD players, HDTV receivers, satellite systems or CD players to the Optical or Coaxial inputs on the rear or front panel
A
will light, and the audio will begin

#$
. When the digital
#$
or the front
. In order to pro-
vide a backup signal and a source for analog stereo recording, the analog outputs provided on digital source equipment should also be connect­ed to their appropriate inputs on the AVR 2000 rear panel (e.g., connect the analog stereo audio output from a DVD to the DVD inputs rear panel when you connect the source’s digital outputs).
When playing a digital source such as DVD, first select its input using the remote or front panel controls as outlined in this manual in order to feed its video signal (if any) to the TV monitor and to provide its analog audio signal for record­ing. When the digital input appropriate with the DVD player is not selected automatically (due to the input settings made earlier during the system configuration, see page 18), select the digital source by pressing the Digital Input Selector button
FÒand then using the
C
on the remote or the Selector buttons
on the front panel to OPTICAL or COAXIAL appear in the Main Information Display X and Display Indicators source is playing, the AVR 2000 will automatical­ly detect whether it is a multichannel Dolby Digital, DTS source,MP3 or a conventional PCM signal, which is the standard output from CD players.A Bitstream Indicator the Main Information Display that the digital signal is Dolby Digital, DTS,MP3 or PCM. Note that a digital input (e.g. coaxial) remains associated with any analog input (e.g. DVD) as soon as it is selected, thus the digital input need not be re-selected each time the appropriate input choice (e.g. DVD) is made.
Digital Status Indicators
When a digital source is playing, the AVR 2000 senses the type of bitstream data that is present. Using this information, the correct surround mode will automatically be selected. For example, DTS bitstreams will cause the unit to switch to DTS decoding, and Dolby Digital bitstreams will enable Dolby Digital decoding.When the unit senses PCM data, from CDs and LDs and some music DVDs or certain tracks on normal DVDs,it will allow the appropriate surround mode to be selected manually. Since the range of available surround modes depends on the type of digital data that is present, the AVR 2000 uses a variety of indicators to let you know what type of signal is present.This will help you to understand the choice of modes and the input channels recorded on the disc.
When a digital source is playing, a Bitstream
Indicator
signal is playing:
DOLBY D: When the DOLBY D indicator lights, a Dolby Digital bitstream is being received.
A
choose any of the
BE
. When the digital
will light to show which type of
on the
⁄/¤
buttons
inputs, as they
A
will light in
Ú
to confirm
5
Depending on the audio track selected on the source player and number of channels on the disc, different surround modes are possible.Note that only one channel without subwoofer, called ”1.0” audio,or all five channels with subwoofer (”5.1” audio) or all steps between can be record­ed on digitally surround encoded audio tracks (see NOTE below).With all those tracks, except ”2.0” audio,only the Dolby Digital and VMAx modes are available.When the Dolby Digital sig­nal is only two channel (”2.0”) these two chan­nels (l and r) often contain Pro Logic surround informations.With those tracks the AVR 2000 automatically switches to the Pro Logic mode, but you may also select the Vmax mode.
DTS: When the DTS indicator lights, a DTS bit­stream is being received.When the unit senses this type of data, only the DTS mode may be used.
PCM: When the PCM indicator lights, a standard Pulse Code Modulation, or PCM, signal is being received.This is the type of digital audio used by conventional compact disc and laser disc record­ings.When a PCM bitstream is present, all modes except Dolby Digital and DTS are available.Note that the PCM signal format can be selected on the DVD player with any audio track, even with Dolby Digital tracks (but not with Dolby Digital decod­ing). So,if selected, even ”2.0”D.D. audio tracks can be played with all surround modes, also with the most effective Logic 7.
MP3: When the MP3 indicator lights, a compat­ible MPEG 1/Layer 3 digital signal is being received. This is the popular audio format used by many computer programs for recording com­pressed audio files.When an MP3 bitstream is present, the sound will automatically be played in the stereo (surround off) mode.The surround modes are not available during MP3 playback.
In addition to the Bitstream Indicators, the AVR 2000 features a set of unique channel input indicators that tell you how many channels of digital information are being received and if the digital signal is interrupted.
These indicators are the L/C/R/LS/RS/LFE letters that are inside the center boxes of the
Speaker/Channel Input Indicators
front panel Main Information Display When a standard analog stereo or matrix sur­round signal is in use, only the “L” and “R” indi­cators will light, as analog signals have only left and right channels, respectively, even surround recordings, carry surround information on the left and right channels only.
Digital signals, however, may have one to six sep­arate channels, depending on the program mate­rial, the method of transmission and the way in which it was encoded.When a digital signal is playing, the letters in these indicators will light in response to the specific signal being received. It
P
in the
Ú
.
26 OPERATION
Operation
is important to note that although Dolby Digital, for example, is referred to as a “5.1” system, not all Dolby Digital DVD or audio tracks selected on DVD or other Dolby Digital programs are encod­ed for 5.1. Thus,it is sometimes normal for a DVD with a Dolby Digital soundtrack to trigger e.g. only the “L” and “R” indicators.
NOTE: Many DVD discs are recorded with both “5.1” and “2.0”versions of the same sound­track, the ”2.0” version often is used with other languages.When playing a DVD,always be cer­tain to check the type of material on the disc. Most discs show this information in the form of a listing or icon on the back of the disc jacket. When a disc does offer multiple soundtrack choices you may have to make some adjustments to your DVD player (usually with the “Audio Select” button or in a menu screen on the disc) to send a full 5.1 feed to the AVR 2000 or to select the appropriate audio track and thus lan­guage (”2.0” audio tracks can be played with all surround modes, even with Logic 7,see indicator ”PCM” on page 16). It is also possible for the type of signal feed to change during the course of a DVD playback. In some cases the previews of special material will only be recorded in 2.0 audio, while the main feature is available in 5.1 audio.As long as your DVD player is set for 6­channel output, the AVR 2000 will automatically sense changes to the bitstream and channel count and reflect them in these indicators.
The letters used by the Speaker/Channel Input
Indicators
stream has been interrupted. This will happen when a digital input source is selected before the playback starts, or when a digital source such as a DVD is put into a Pause mode.The flashing indicators remind you that the playback has stopped due to the absence of a digital signal and not through any fault of the AVR. This is nor­mal, and the digital playback will resume once the playback is started again.
Night Mode
A special feature of Dolby Digital is the Night mode, which enables Dolby Digital input sources to be played back with full digital intelligibilty while reducing the maximum peak level and lift­ing the low levels by abruptly loud transitions from disturbing others without reducing the impact of the digital source. The Night mode is available only when Dolby Digital mode is selected.
The Night mode may be engaged when a Dolby Digital DVD is playing by pressing the Night Button buttons Cto select either the middle range or full compression versions of the Night mode.To turn the Night mode off,press the
C
video display and the Main Information
P
also flash to indicate when a bit-
1/4 to 1/3. This prevents
A
on the remote. Next,press the ⁄/¤
/¤ buttons
until the message in the lower third of the
Display
X
reads D-RANGE OFF. When
the Night mode is active, the Night Mode
Indicator
The Night mode may also be selected to always be on at either level of compression using the options in the Surround setting. See page 21 for informa­tion on setting this option.
IMPORTANT NOTES ON DIGITAL PLAYBACK:
1. When the digital playback source is stopped, or in a pause, fast forward or chapter search mode, the digital audio data will momentarily stop, and the channel position letters inside the
Speaker/Channel Indicators
This is normal and does not indicate a problem with either the AVR 2000 or the source machine. The AVR 2000 will return to digital playback as soon as the data is available and when the machine is in a standard play mode.
2.Although the AVR 2000 will decode virtually all DVD movies, CDs and HDTV sources, it is possible that some future digital sources may not be com­patible with the AVR 2000.
3. Note that not all digitally encoded programs and not all audio tracks on a DVD contain full
5.1-channel audio. Consult the program guide that accompanies the DVD or laser disc to deter­mine which type of audio has been recorded on the disc. The AVR 2000 will automatically sense the type of digital surround encoding used, indi­cate it in the Bitstream Indicators
Channel Input Indicators
accommodate it.
4. When a Dolby Digital or DTS source is playing, you normally may not be able to select some of the analog surround modes such as Dolby Pro Logic, Dolby 3, Stereo, Hall, Theater, 5CH Stereo or Logic 7, except with special audio tracks (see indication ”Dolby Digital” on previous page) or data format selected (see ”PCM” on previous page).
5. When a Dolby Digital or DTS source is playing, it is not possible to make an analog recording using the Tape

to any digital input of the AVR 2000 only. But the analog two channel signal of that source, the ”Downmix” to Stereo or Dolby Surround, can be recorded by connecting its analog audio outputs to the appropriate analog inputs (e.g. DVD) of the AVR 2000, even if the digital input of the AVR 2000 remains selected.Additionally, the dig­ital signals will be passed through to the Digital Audio Outputs.
N
will also illuminate.
P
will flash.
A
and
P
and adjust to
or Video 1 or Video 2 or
record outputs, if the source is connected
Tape Recording
In normal operation, the audio or video source selected for listening through the AVR 2000 is sent to the record outputs.This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for Tape Outputs or 2 Outputs
When a digital audio recorder is connected to any of the Digital Audio Outputs able to record the digital signal using a CD-R, MiniDisc or other digital recording system. Note that all digital signals will be passed through to both, coaxial and optical, digital out­puts simultanously, no matter which kind of digi­tal input was selected.
NOTES:
• The digital outputs are active only when a digital signal is present, and they do not convert an ana­log input to a digital signal, or change the format of the digital signal (e.g. Dolby Digital to PCM or vice versa, but coaxial digital signals are converted to optical signals and vice versa). In additon, the digital recorder must be compatible with the out­put signal. For example, the PCM digital input from a CD player may be recorded on a CD-R or MiniDisc, but Dolby Digital or DTS signals may not.
• To make an analog recording of a Dolby Digital or DTS source is not possible, if the source is con­nected to a digital input of the AVR 2000 only. But the analog two channel signal of that source can be recorded (see item 5, ”Important Notes on Digital Playback” above).

in the record mode.
or Video 1
, you are
OPERATION 27
Operation
Output Level Trim Adjustment
Normal output level adjustment for the AVR 2000 is established using the test tone, as outlined on pages 21 and 22. In some cases, however, it may be desirable to adjust the output levels using program material such as a test disc, or a selection you are familiar with. Additionally, the output level for the subwoofer and those for the Stereo and VMAx modes can only be adjust­ed using this procedure.
To adjust the output levels using program materi­al, first select the surround mode for which you want to trim the speakers(see NOTE below) by selecting the appropriate input, associated with the desired surround mode, start your program material source and set the reference volume for the front left and front right channels using the
Volume Control
Once the reference level has been set, press the Channel Select button
FRONT L LEV will appear in the Main Information Display
first press the Set button the Selector buttons
C
to raise or lower the level. DO NOT use the volume control, as this will alter the reference setting.
Once the change has been made, press the Set button
EÓand then press the Selector but-
tons
5
or the ⁄/¤ buttons Cto select the next output channel location that you wish to adjust. To adjust the subwoofer level, press the Selector buttons 5 or the until WOOFER LEV appears in the Main
Information Display
subwoofer was selected during the speaker con­figuration, see page 18).
Press the Set button the desired channel appears in the Main
Information Display
instructions shown above to adjust the level.
Repeat the procedure as needed until all chan­nels requiring adjustment have been set. When all adjustments have been made press the Set
button
EÓtwice, the AVR 2000 will return
to normal operation.
(".
BÛand note that
X
. To change the level,
EÓ, and then use
5
or the
⁄/¤
buttons
/¤ buttons
X
. (Only available if the
EÓwhen the name of
X
, and follow the
C
NOTE:The output levels may be separately trimmed for each digital and analog surround mode. If you wish to have different trim levels for a specific mode, select that mode and then follow the instructions in the steps shown above.
Changing the levels using trim adjustment as described above will automatically change the level settings shown in the Output Adjustment (see page 21) correspondingly (and vice versa) and will remain in the AVR 2000´s memory system, even when the unit is turned off. With Stereo and Vmax modes the adjustment proce­dure described above is the only way to trim the output level (e.g. to match the Vmax level with other modes).
Display Brightness
The AVR 2000’s front panel Main Information Display
that is sufficient for viewing in a normally lit room. However, in some home theater installa­tions, you may wish to occasionally lower the brightness of the display, or turn it off completely.
The display brightness may be changed by press­ing and holding the Set button for three seconds until the message in the Main
Information Display
FULL. Within five seconds,press the front panel Selector buttons brightness display level is shown. At that point, press the Set button setting.
Once the desired brightness level is selected, it will remain in effect until it is changed again or until the unit is turned off.
Ú
is set at a default brightness level
Ó
on the front
X
reads VFD
5
until the desired
Ó
again to enter the
Memory Backup
This product is equipped with a memory backup system that preserves tuner presets and system configuration information if the unit is turned off completely, accidentally unplugged or subjected to a power outage.This memory will last for approximately two weeks, after which time all information must be reentered.
28 OPERATION
Operation
Tuner Operation
The AVR 2000’s tuner is capable of tuning AM, FM and FM Stereo broadcast stations and receiv­ing RDS data. Stations may be tuned manually, or they may be stored as favorite station presets and recalled from a 30 position memory.
Station Selection
1. Press the AM/FM Tuner Select button on the remote to select the tuner as an input. The tuner may be selected from the front panel by either pressing the Input Source Selector
!
until the tuner is active or by pressing the
Tuner Band Selector
2. Press the AM/FM Tuner Select button or Tuner Band Selector9again to switch between AM and FM so that the desired frequen­cy band is selected.
3. Press the Tuner Mode button remote or hold the Band Selector front panel pressed for 3 seconds to select manu­al or automatic tuning.
When the AUTO indicator Main Information Display the tuner will only stop at those stations that have a strong enough sig­nal to be received with acceptable quality.
When the AUTO indicator the tuner is in a manual mode and will stop at each frequency increment in the selected band.
4. To select stations press any Tuning button
J
. When the AUTO indicator Wis illumin-
ated, press the button to cause the tuner to search for the next highest or lowest frequency station that has an acceptable signal or hold the button pressed to tune more quickly and release it to start the auto search. In the Auto mode the tuner will play each station in stereo or mono mode, just as the program is transmitted. If the
AUTO indicator Tuning button
cy increment at a time, or press and hold it to locate a specific station. When the TUNED indi­cator
V
illuminates, the station is properly
tuned and should be heard with clarity.
9
at any time.
H
W
is illuminated in the
W
is not illuminated,
W
is not illuminated, tap the
8Jto advance one frequen-
on the
9
6
6
on the
8
5. Stations may also be tuned directly by press­ing the Direct button the Numeric Keys station’s frequency. The desired station will auto­matically be tuned after the latest number is entered. If you press an incorrect button while entering a direct frequency, press the Clear but­ton
P
to start over.
NOTE:When the FM reception of a stereo station is weak, audio quality will be increased by switching to Mono mode by pressing the Tuner Mode button holding the Band Selector panel pressed for 3 seconds until the STEREO indicator
I
, and then pressing
G
that correspond to the
H
on the remote or
9
on the front
U
goes out.
Preset Tuning
Using the remote, up to 30 stations may be stored in the AVR 2000’s memory for easy recall using the front panel controls or the remote.
To enter a station into the memory, first tune the station using the steps outlined above.Then:
1. Press the Memory button remote. Note that MEMORYindicator illuminate and flash in the Main Information
Display
2. Within five seconds, press the Numeric Keys
G
wish to store this station’s frequency. Once entered, the preset number will appear in the
Preset Number/Sleep Time Display
3. Repeat the process after tuning any additional stations to be preset.
Recalling Preset Stations
• To manually select a station previously entered in the preset memory, press the Numeric Keys
G
memory location.
• To manually tune through the list of stored preset stations one by one, press the Preset Stations Selector buttons front panel or remote.
Ú
.
corresponding to the location where you
that correspond to the desired station’s
Q
on the
Q
)Oon the
T
will
.
OPERATION 29
Operation
RDS Operation
The AVR 2000 is equipped with RDS (Radio Data System), which brings a wide range of information to FM radio. Now in use in many countries, RDS is a system for transmitting station call signs or network information, a description of station program type, text messages about the station or specifics of a musical selection, and the correct time.
As more FM stations become equipped with RDS capabilities, the AVR 2000 will serve as an easy­to-use center for both information and entertainment. This section will help you take maximum advantage of the RDS system.
RDS Tuning
When an FM station is tuned in and it contains RDS data, the RDS Indicator nate and the AVR 2000 will automatically dis­play the station’s call sign or other program serv­ice in the Main Information Display
RDS Display Options
The RDS system is capable of transmitting a wide variety of information in addition to the initial station call sign that appears when a sta­tion is first tuned. In normal RDS operation the display will indicate the station name, broadcast network or call letters. Pressing the RDS button
@Nenables you to cycle through the various
data types in the following sequence:
AE
will illumi-
X
.
• The current time of day (CT). Note that it may take up to two minutes for the time to appear, in that time the word TIME will flash in the information display when CT is selected. The CT
Indicator
being received. Please note that the accuracy of the time data is dependent on the radio station, not the AVR 2000.
Some RDS stations may not include some of these additional features. If the data required for the selected mode is not being transmitted, the Main Information Display a NO TYPE, NO TEXT or NO TIME message after the individual time out.
In any FM mode the RDS function requires a strong enough signal for proper operation. If you receive a partial message, or any of the RDS, PTY, CT or RT Indicators
AB
antenna or tune to another stronger RDS station.
AC
will illuminate when time data is
X
will show
AEADAC
going on and off,try slowly adjusting the
Program Search (PTY)
An important feature of RDS is its capability of encoding broadcasts with Program Type (PTY) codes that indicate the type of material being broadcast. The following list shows the abbreviations used to indicate each PTY, along with an explanation of the PTY:
• (RDS ONLY)
• (TRAFFIC)
NEWS: News
AFFAIRS: Current Affairs
INFO: Infomation
SPORT: Sports
EDUCATE: Educational
DRAMA: Drama
CULTURE: Culture
SCIENCE: Science
VARIED: Varied Speech Programs
POPM: Popular Music
ROCKM: Rock Music
M.O.R.M.: Middle-of-the-Road Music
• The station’s call letters (with some private stations other information too).
• The station’s frequency.
• The Program Type (PTY) as shown in the list below.The PTY Indicator when this data is being received.
• A “text” message (Radiotext, RT) containing special information from the broadcast station. Note that this message may scroll across the display to permit messages longer than the eight positions in the display. Depending on signal quality, it may take up to 30 seconds for the text message to appear; in that time,the word TEXTwill flash in the Information Display when RT is selected.The RT Indicator illuminate when text data is being received and ready to be displayed.
AD
will illuminate
AB
will
LIGHTM: Classical Music
CLASSICS: Serious Classical Music
OTHERM: Other Music
WEATHER: Weather Information
FINANCE: Financial Programs
CHILDREN: Children’s Programs
SOCIAL A: Social Affairs Programs
RELIGION: Religious Broadcasts
PHONE IN: Phone-In Programs
TRAVEL: Travel and Touring
LEISURE: Leisure and Hobby
30 OPERATION
Operation
JAZZ: Jazz Music
COUNTRY: Country Music
NATIONAL: National Music
OLDIES: Oldies Music
FOLK M: Folk Music
DOCUMENT: Documentary Programs
TEST: Emergency Test
ALARM: Emergency Broadcast Information
You may search for a specific Program Type (PTY) by following these steps:
1. Press the RDS button rent PTY is shown in the Main Information
Display
X
.
2. While the PTY is shown, press the Preset Up/Down button to scroll through the list of available PTY types, as shown above.To simply search for the next station transmitting any RDS data, use the Preset Up/Down button ONLY appears in the display.
3. Press any of the Tuning Up/Down buttons
8J, the tuner begins to scan the FM band
upwards or downwards for the first station that has RDS data that matches the desired selec­tion, and acceptable signal strength for quality reception.
4. While the PTY Indicator display, the tuner will make up to one complete scan of the entire FM band for the next station that matches the desired PTY type and has acceptable reception quality. If no such station is found, the display will read NONEfor some seconds and the tuner will return to the last FM station in use before the search.
@Nuntil the cur-
)Oor hold them pressed
)Ountil RDS
AD
flashes in the
NOTE: Many stations do not transmit a specific PTY. The display will show NONE, when such a station is selected and PTY is active.
NOTE: Some stations transmit constant traffic information. To identify as traffic station, they transmit a specific traffic code constantly, which causes the TA Indicator play.These stations can be found by selecting TRAFFIC, the option in front of NEWS in the list. The AVR 2000 will find the appropriate station, even if it is not broadcasting traffic information when the search is made.
AA
to light in the dis-
OPERATION 31
Programming the Remote
The AVR 2000 is equipped with a powerful remote control that will control not only the receiver’s functions, but also most popular brands of audio and video equipment, including CD players,TV sets,cable boxes,VCRs, satellite receivers and other home-theater equipment. Once the AVR 2000’s remote is programmed with the codes for the products you own, it is possible to eliminate most other remotes and replace them with the convenience of a single universal remote control.
Programming the Remote with Codes
As shipped from the factory, the remote is fully programmed for all AVR 2000 functions, as well as those of most Harman Kardon CD changers, DVD players, CD players and cassette decks. In addition, by following one of the methods below, you may program the remote to operate a wide range of devices from other manufacturers.
Note: The Input Selector button Video 4 cannot be programmed with codes as it functions as input selector for the AVR only. Moreover, only the default code "001" can be programmed on the AVR Selector button
5
.
Direct Code Entry
This method is the easiest way to program your remote to work with different products.
1. Use the tables in the pages 38-45 to deter­mine the three-digit code or codes that match both the product type (e.g.,VCR,TV), and the specific brand name. If there is more than one number for a brand, make note of the different choices.
2. Turn on the unit you wish to program into the AVR 2000 remote.
3. Press and hold both the Input Selector for the type of product to be entered (e.g.,VCR, TV) and the Mute button
time.When the Program Indicator amber and begins flashing, release the buttons.It is important that you begin the next step within 20 seconds.
4. If the unit you wish to program into the AVR 2000 remote has a remotable Power on/off func­tion, follow these steps:
a. Point the AVR 2000’s remote towards the unit
to be programmed, and enter the first three­digit code number using the Numeric buttons
G
. If the unit being programmed turns off, the
correct code has been entered. Press the Input
Selector
4
again, and note that the red
light under the Input Selector will flash three times before going dark to confirm the entry.
4
4
at the same
2
turns
b. If the product to be programmed does NOT
turn off,continue to enter the three-digit code numbers until the equipment turns off.At this point, the correct code has been entered. Press the Input Selector
4
again and note that
the red light under the Input Selector will flash three times before going dark to confirm the entry.
5. If the Power function of the unit to be pro­grammed cannot be remoted, follow these steps (max. 20 seconds after step 3 above,or else step 3 must be repeated first):
a. Enter the first three-digit code number using
the Numeric buttons
Input Selector
G
and press the
4
again. Press the remote
button of any transport function remotable with the unit, e.g.Pause or Play
L
.If the unit being programmed starts that func­tion, the correct code has been entered.
b. If the unit does not start the function whose
button was pressed, repeat steps 3 and 5a above with the next three-digit code number listed in the setup code table for that brand and product type, until the unit reacts properly on the transport function transmitted.
6. Try all of the functions on the remote to make certain that the product operates properly.Keep in mind that many manufacturers use a number of different combinations of codes, so it is a good idea to make certain that not only does the Power control work, but that the volume, channel and transport controls work as they should. If functions do not work properly, you may need to use a different remote code.
7. If the unit does not react to any code en­tered, if the code for your product does not appear in the tables in this manual, or if not all functions operate properly, try programming the remote with the Auto Search Method.
Note on Using the AVR 2000 remote with a Harman Kardon CD Recorder.
As shipped from the factory the remote is pro­grammed for controlling Harman Kardon CD players. But it is able to control most functions of the CD Recorder CDR2 and CDR20 (see func­tion list on page 36) too after the code ”002” is entered to the CD Selector button
2
as described above. For returning to the CD player control commands the code ”001” must be entered.
Auto-Search Method
If the unit you wish to include in the AVR 2000’s remote is not listed in the code tables in this manual or if the code does not seem to operate properly, you may wish to program the correct code using the Auto Search method that follows. Note that the Auto Search method works only
with units whose Power functions can be remoted:
1. Turn on the product that you wish to include in the AVR 2000 remote.
2. Press and hold both the Input Selector
4
for the type of product to be entered (e.g.,VCR, TV) and the Mute button time.When the Program Indicator
at the same
2
turns amber and begins flashing, release the buttons.It is important that you begin the next step within 20 seconds.
3. To find out if the code for your unit is pre-pro­grammed, point the AVR 2000 remote towards the unit to be programmed, and press and hold
the
buttonC.This will send out a series of
codes from the remote’s built-in data base, with each flash of the red light under the Input
Selector
4
indicating that a code has been sent.When the device to be programmed turns off,immediately release the
buttonC. Note that it may take one minute or more until the right code is found and the unit turns off.
4. When the
button was not released in time after the unit turned off,the proper code will be ”overrun”. That’s why a function test should be made: Turn the unit on again and,while the
Input Selector
4
still lights red, press the
buttonConce, than the ¤button Conce too.When the unit turns off, the right code was found, when not, the code was ”overrun”. To re­find the correct, while the Input Selector still lights red, press (not hold pressed) the
4
¤
button Drepeatedly to step backwards through the codes available and observe the reaction of the unit at each press.As soon as the unit turns off the correct code is found.
5. Press the Input Selector
4
again, and note that the red light will flash three times before going dark to confirm the entry.
6. Try all of the functions on the remote to make certain that the product operates. Keep in mind that many manufacturers use a number of differ­ent combinations of codes, and it is a good idea to make certain that not only the Power control works, but the volume, channel and transport controls, as appropriate. If all functions do not work properly, you may need to Auto-Search for a different code, or enter a code via the Direct Code Entry method.
32 PROGRAMMING THE REMOTE
Programming the Remote
Macro Programming
Macros enable you to easily repeat frequently used combinations of commands with the press of a single button on the AVR 3000’s remote con­trol. Once programmed,a macro will send out up to 19 different remote codes in a pre-deter­mined sequential order enabling you to automate the process of turning on your system, changing devices, or other common tasks. The AVR’s remote can store up to five separate macro command sequences, one that is associated with the Power On button by pressing the Macro buttons
1. Press the Mute button button button est selected Input Selector will light red, and the Program Indicator
2. Enter the steps for the macro sequence by pressing the button for the actual command step. Although the macro may contain up to 19 steps, each button press, including those used to change devices, counts as a step. The Program
Indicator
button press as you enter commands. NOTE: While entering commands for Power On of
any device during a macro sequence, press the Mute button Power ON button.
0
, and four more that are accessed
K
.
and the Macro
K
to be programmed or the Power-On
0
at the same time. Note that the lat-
2
will flash amber.
2
will flash green to confirm each
. DO NOT press the actual
• Remember to press the appropriate Input Selector button changed to another device.This is also needed for the AVR Selector button as it’s not lit red and AVR functions shall be pro­grammed.
3. When all the steps have been entered, press the Sleep button The red light under the Input Selector will blink and then turn off.
Example: To program the Macro 1 so that it turns on the AVR 3000, TV and a Sat­Receiver, follow these steps:
• Press the Macro 1 button buttons at the same time and then release them.
• Note that the Program Indicator will flash amber.
• Press the AVR Selector
• Press the Mute power on command.
• Press the VID 2 Input Selector button indicate the next command is for “TV Power On.”
• Press the Mute Power On Command.
4
before functions are
5
8
to enter the commands.
K
and Mute
5
.
button to store the AVR’s
button to store the TV
itself,as long
45
K
button
4
• Press the VID 3 Input Selector button to indicate the next command is for “Sat-Receiver Power On.”
• Press the Mute Receiver Power On command.
• Press the Sleep/Channel Up button complete the process and store the macro sequence.
After following these steps, each time you press the Macro 1 button all Power On commands.
Erasing Macro Commands
To remove the commands that have been pro­grammed into one of the Macro buttons, follow these steps:
1. Press the Mute button button
K
wish to erase.
2. Note that the Program Indicator
to
flash amber, and the LED under the AVR
Selector
3. Within ten seconds, press the Surround Mode Selector/Channel Down button
4. The red LED under the AVR Selector will go out, and the Program Indicator green and flash three times before it goes out.
5. When the Program Indicator the Macro has been erased.
button to store the Sat-
K
, the remote will send
and the Macro
that contains the commands you
5
will turn red.
2
2
4
8
to
2
will
9
will turn
goes out,
.
PROGRAMMING THE REMOTE 33
Programming the Remote
Programmed Device Functions
Once the AVR 2000’s remote has been pro­grammed for the codes of other devices,press the appropriate Input Selector remote from control over the AVR 2000 to the additional product.When you press any of these buttons, it will briefly flash in red to indicate that you have changed the device being controlled.
When operating a device other than the AVR 2000, the controls may not correspond exactly to the function printed on the remote or button. Some commands, such as the volume control,are the same as they are with the AVR 2000. Other buttons will change their function so that they correspond to a secondary label on the remote. For example,the Sleep and Surround mode selec­tor buttons also function as the Channel Up and Channel Down buttons when operating most TV sets,VCRs or Sat-Receivers.
For some products,however, the function of a particular button does not follow the command printed on the remote. In order to see which function a button controls, consult the Function List tables printed on page 36. To use those tables, first check the type of device being con­trolled (e.g.,TV,VCR). Next, look at the remote control diagram or page 36. Note that each but­ton has a number on it.
To find out what function a particular button has for a specific device, find the button number on the Function List and then look in the column for the device you are controlling. For example, but­ton number 50 is the Macro 2 button for the AVR 2000, but it is the “Favorite”button for many cable television boxes and satellite receivers. Button number 29 is the Delay button for the AVR 2000, but the Open/Close button for CD players.
Note that the numbers used to describe the but­ton functions at the left for the purposes of describing how a button operates are a different set of numbers than those used in the rest of this manual to describe the button functions for the AVR 3000.
4
to change the
Notes on Using the AVR 2000 Remote With Other Devices.
• Manufacturers may use different code sets for the same product category. For that reason, it is important that you check to see if the code set you have entered operates as many controls as possible. If it appears that only a few functions operate, check to see if another code set will work with more buttons.
• Depending on the brand and product type used the functions listed in the Function List tables may not correspond with the function the unit reacts on the command. In these cases it’s a good idea to edit the reaction of the unit into the corresponding line of the table or to set up a separate list.
• When a button is pressed on the AVR 2000 remote, the red light under the Input Selector
4
for the product being operated should flash briefly. If the Device Control Selector flashes for some but not all buttons for a particular prod­uct, it does NOT indicate a problem with the remote, but rather that no function is pro­grammed for the button being pushed.
• The remote was pre-programmed with codes for units of the latest generation, but some codes may differ from those needed for earlier units.
Volume Punch-Through
The AVR 2000’s remote may be programmed to operate the Volume Control
Mute
from either the TV or the AVR in con­junction with any of the six devices controlled by the remote. For example, since the AVR 2000 will likely be used as the sound system for TV view­ing, you may wish to have the AVR’s volume acti­vated although the remote is set to run the TV.
To program the remote for Volume Punch­Through, follow these steps:
1. Press the Input Selector wish to have associated with the volume control and the Mute button the red light illuminates under the Input Selector
4
and note that the Program Indicator
will flash amber.
2. Press the Volume Up button that.the Program Indicator flashing and stay amber.
3. Press either the AVR Selector
Input Selector
tem’s volume control you wish to have attached for the punch-through mode.The Program
Indicator
then go out to confirm the data entry. Example: To have the AVR’s volume control
activated even though the remote is set to con­trol the TV, first press the Video/TV Input
Selector same time. Next,press the Volume Up button
"
, followed by the AVR Input Selector5.
NOTE: Should you wish to return the remote to
the original configuration after entering a Volume Punch-Through,you will need to repeat the steps shown above. However, press the Video/TV Input Selector in steps one and three.
4
, depending on which sys-
2
will blink green three times and
4
and the Mute button at the
"
and the
4
for the unit you
at the same time until
"
2
will stop
5
2
and note
or the
34 PROGRAMMING THE REMOTE
Programming the Remote
Channel Control Punch-Through
The AVR 3000’s remote may be programmed to operate so that the channel control function for either the TV, cable or satellite receiver used in your system may be used in conjunction with one of the other devices controlled by the remote. For example, while using and controlling the VCR, you may wish to change channels on a cable box or satellite receiver without having to change the device selected by the AVR 3000 or the remote. To program the remote for Channel Control Punch-Through, follow these steps:
1. Press the Input Selector button device you wish to have the channel control asso­ciated with and the Mute button same time until the red light illuminates under the
Input Selector Indicator
2. Press the Volume Down button Program Indicator
stay amber.
3. Press and release the AVR Selector button used to change the channels.The Program
Indicator
then go out to confirm the data entry. Example: To control the channels using your TV
while the remote is set to control the VCR,first press the VID 1/VCR Input Selector button and the Mute button at the same time. Next, release them and press the Volume Down but­ton
"
Selector button NOTE:To remove the Channel Control Punch-
Through and return the remote to its original con­figuration, repeat the steps shown in the example above. However, press the VID 1/VCR Input Selector in Steps 1 and 3.
4
and the Program
2
flashes amber.
2
will stop flashing and
4
for the device that will be
2
will blink green three times and
, followed by the VID 2/TV Input
4
.
5
4
at the
"
or Input
for the
.The
4
Transport Control Punch-Through
The AVR 3000’s remote may be programmed to operate so that the Transport Control Functions
L
(Play, Stop, Fast Forward, Rewind, Pause and Record) for a VCR,DVD or CD will operate in con­junction with one of the other devices controlled by the remote. For example, while using and con­trolling the TV, you may wish to start or stop your VCR or DVD without having to change the device selected by the AVR 3000 or the remote. To pro­gram the remote for Transport Control Punch­Through, follow these steps:
1. Press the Input Selector you wish to have the channel control associated with and the Mute button until the red light illuminates, under the Input
Selector
flashes amber.
2. Press the Play button
Indicator
3. Press and release the AVR Selector button used to change the channels.The Program Indicator
then go out to confirm the data entry. Example: To control the transport of a CD player
while the remote is set to control the TV, press the
VID 2/TV Input Selector button Mute button
them and press the Play button by the CD Input Selector button
NOTE:To remove the Channel Control Punch­Through and return the remote to its original con­figuration, repeat the steps shown in the example above. However, press the VID 2/TV Input
Selector in Steps 1 and 3. NOTE: Before programming the remote for
Volume,Channel or Transport Punch-Through, make certain that any programming needed for the specific TV, CD, DVD, Cable or Satellite Receivers has been completed.
4
and the Program Indicator
2
will stop flashing and stay amber.
4
2
will blink green three times and
at the same time. Next,release
4
for the device
at the same time
2
L
.The Program
5
or Input
for the device that will be
4
and the
L
, followed
4
.
Resetting the Remote Memory
As you add components to your home-theater sys­tem, occasionally you may wish to totally repro­gram the remote control without the confusion of any commands, macros or ”Punch-Through“ pro­gramming that you may have done.To do this, it is possible to reset the remote to the original factory defaults and command codes by following these steps. Note, however, that once the remote is reset, all commands or codes that you have entered will be erased and will need to be re­entered:
1. Press any of the Input Selector buttons and the ”O“ button Gat the same time until the Program Indicator amber.
2. Press the ”3“ button
3.The red LED under the Input Selector go out and the Program Indicator flashing and turn green.
4.The Program Indicator until the remote is reset. Note that this may take a while, depending on how many commands are in the memory and need to be erased.
5.When the Program Indicator the remote has been reset to the factory settings.
2
begins to flash
G
three times.
2
will remain green
2
2
goes out,
4
4
will
will stop
PROGRAMMING THE REMOTE 35
Function List
1
4
5
6
7
8
9
10
11
13
17
21
22
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
23
14
15
16
20
19
18
12
2
3
2000
No. Button Name AVR Function DVD CD/CDR
1 Power Off Power Off Power Off Power Off 2 Power On Power On Power On Power On 3 Mute Mute 4 AVR AVR Select 5 DVD DVD Input Select DVD Select 6 CD CD Input Select CD Select 7 Tape Tape Input Select 8 VID 1 Video 1 Select
9 VID 2 Video 2 Select 10 VID 3 Video 3 Select 11 VID 4 Video 4 Select 12 AM/FM Tuner Select 13 Sleep Sleep 14 Test Test Tone -/Input Select 15 TV TV/DVD -/CDP Select 16 Volume Up Volume Up Volume Up 17 Surround Select 18 Night Night Mode Select Subtitle on/off 19 Spare 20 Volume Down Volume Down Volume Down 21 Channel/Guide Channel Trim Title
22 23 Speaker/Menu Speaker Adjust Menu Intro/­24
25 Set Set Enter 26
27 Digital/Exit
¤
28 29 Delay/Prev. Ch. Delay Adjust Return Open/Close 30 1 111 31 2 222 32 3 333 33 4 444 34 5 555 35 6 666 36 7 777 37 8 888 38 Tun-M Tuner Mode Chapter Repeat 39 9 999 40 0 000 41 Memory Memory Audio Time/CDR Display 42 Tune Up Tune Up 43 Direct Direct Tuner Entry Angle Random 44 Clear Clear Clear Clear 45 Preset Up Preset Tune Up Slow Forward +10/­46 Tune Down Tune Down -/ 47 RDS Disc Skip Disc Skip 48 Preset Down 49 M1 50 M2 51 M3 52 M4 53 Rewind R. Search R. Search 54 Play Play Play 55 Fast Forward F. Search F.Search 56 Record -/Record 57 Stop Stop Stop 58 Pause Pause Pause 59 Skip Down Skip – Skip – 60 Skip Up Skip + Skip +
Surround Mode Select
Move/Adjust Up Up
Left
Right Digital Input Select Move/Adjust Down
Preset Tune Down
Open/Close
Down
Slow Rev
-/CDR Select
Track Increment
36 FUNCTION LIST
Function List
No. Button Name Tape VCR (VID 1) TV (VID 2) CBL (VID 3) SAT(VID 3)
1 Power Off Power Off Power Off Power Off Power Off Power Off 2 Power On Power On Power On Power On Power On Power On 3 Mute Mute 4 AVR 5 DVD 6 CD 7 Tape Tape Select 8 VID 1 VCR Select
9 VID 2 TV Select 10 VID 3 VID 3 Select 11 VID 4 12 AM/FM 13 Sleep Channel + Channel + Channel + Channel + 14 Test 15 TV TV/VCR TV/VCR TV/Cable TV/Sat 16 Volume Up Volume Up Volume Up 17 Surround Select Channel – Channel – Channel – 18 Night 19 Spare 20 Volume Down Volume Down 21 Channel/Guide Info/Guide Info/Guide 22 23 Speaker/Menu Menu Menu Menu Menu 24 25 Set Enter Enter Enter Enter 26 27 Digital/Exit Exit Exit Exit Exit 28 29 Delay/Prev. Ch. Prev Channel Prev Channel Prev Channel 30 1 1111 31 2 2222 32 3 3333 33 4 4444 34 5 5555 35 6 6666 36 7 7777 37 8 8888 38 Tun-M 39 9 9999 40 0 0000 41 Memory 42 Tune Up 43 Direct 44 Clear Clear Clear Clear Clear 45 Preset Up 46 Tune Down 47 RDS 48 Preset Down 49 M1 Cancel Sleep PPV Cancel 50 M2 Fav Fav 51 M3 Bypass Next 52 M4 Music Alt 53 Rewind Rewind Rewind Day – Say – 54 Play Play Play 55 Fast Forward Fast Fwd Fast Fwd Day + Day + 56 Record Record/Rec.Pause Record 57 Stop Stop Stop 58 Pause Pause 59 Skip Down Scan – Page – Page – 60 Skip Up Scan + Page + Page +
¤
Up Up Up Up
Left Left Left Left
Right Right Right Right
Down Down Down Down
FUNCTION LIST 37
Setup Code Table: TV
Maker (Brand) Name Code Number (3digit) List
AIWA 110 AKAI 011 020 022 042 053 056 089 093 ALBA 020 040 ARC EN CIEL 017 019 024 056 059 ARCAM 017 BANG & OLUFSEN 088 BEKO 022 BLAUPUNKT 011 075 076 077 BRANDT ELECTRONIQUE 017 019 024 056 059 BRION VEGA 023 088 BRUNS 023 088 BUSH 010 020 040 043 092 BUSH(UK) 044 CGE 105 DAEWOO 022 DECCA(UK) 038 DUMONT 023 088 096 DUMONT-FINLUX 012 044 DYNATRON 020 022 ELBE 095 105 EMERSON 023 088 FERGUSON 001 024 047 062 075 076 077 099 FIDELITY(UK) 099 FINLANDIA 018 FINLUX 012 044 088 096 GEC(UK) 061 GOLDSTAR 022 GOODMANS 010 022 043 GORENJE 124 GRANADA 010 018 022 029 033 104 GRANADA(UK) 043 GRUNDIG 011 075 076 077 096 HANSEATIC 010 020 022 043 HIFIVOX 017 019 024 056 059 080 HITACHI 010 012 015 018 024 026 035 043 055 056 058 059 061
066 069 080 082 085 093 094 101 IMPERIAL 105 INTERFUNK 020 022 023 024 033 056 088 104 INTERVISION 111 113 114 115 116 117 118 119 121 ITT 040 046 092 100 ITT-NOKIA 040 058 092 100 JVC 010 043 047 053 056 092 KARCHER 012 068 KATHREIN 124 KORTING 023 088 LOEWE 027 LOEWE OPTA 020 022 023 088 LUXOR 058 MAGNADYNE 023 088 MARANTZ 022 MARELLI 088 METZ 011 023 075 076 077 088 MINERVA 011 075 076 077 096 MITSUBISHI 007 010 011 013 020 022 023 029 124 038 039 043 046
050 057 075 076 077 079 082 089 090 091 092 NATIONAL 018
38 SETUP CODES
Setup Code Table: TV (continued)
Maker (Brand) Name Code Number (3digit) List
NEC 010 043 NECKERMANN 023 078 088 102 NOKIA 040 046 092 100 NORDMENDE 009 017 019 024 053 056 059 069 080 093 094 ORION 038 040 091 OTTO VERSAND 010 020 022 043 075 076 077 078 092 102 PANASONIC 018 085 PATHE' MARCONI 017 019 024 056 059 PHILCO 023 088 105 PHILIPS 008 014 020 022 023 025 027 032 033 046 047 048 054 060 061 067 068 070 071
078 084 086 088 095 097 099 100 104 107 108 PHOENIX 088 PIONEER 020 022 024 056 069 PROLINE 020 PROTECH 022 QUELLE 011 012 020 022 038 044 075 076 077 096 RADIOLA 022 023 025 033 047 048 060 078 097 RADIOMARELLI 022 023 029 082 088 RBM(UK) 044 REDIFFUSION 029 082 REX 022 025 RFT 122 123 124 125 126 127 RTF 023 SABA 009 017 019 023 024 056 059 069 080 088 093 094 SALORA 018 058 SAMSUNG 022 068 SANYO 010 012 023 038 043 091 092 SBR 022 033 046 047 061 084 086 SCHNEIDER 022 023 025 033 047 048 060 078 086 097 SELECO 022 025 105 SHARP 010 043 SIEMENS 010 011 015 075 076 077 SINGER 023 088 105 SONY 006 010 016 038 043 062 064 065 091 102 103 106 SOUND WAVE 020 STERN 022 025 TANDBERG 023 056 080 TELEFUNKEN 024 056 059 069 TENSAI 022 THOMSON 003 005 009 017 019 024 040 044 053 056 059 069 072 074 080 082 093 094 THORN 047 099 THORN-FERGUSON 024 047 099 102 103 TOSHIBA 001 010 037 042 043 044 063 092 096 105 TRISTAR 099 TRIUMPH 044 UHER 044 ULTRAVOX 023 088 UNIVERSUM 012 075 076 077 102 VOXSON 023 088 WATSON 075 076 077 WEGA 010 043 088 WEGA COLOR 023 WELTBLICK 022 WESTINGHOUSE 022 ZANUSSI 022 025
SETUP CODES 39
Setup Code Table: VCR
Maker (Brand) Name Code Number (3 digit) List
AIWA 039 044 055 073 112 116 121 148 152 AKAI 044 053 090 092 103 149 150 155 AKURA 112 ALBA 061 073 121 144 AMSTRAD 039 107 148 ANITECH 155 ARC EN CIEL 044 045 090 ARISTONA 049 091 109 ASTRA 148 ASTRO SOUND 155 ATLANTIC 155 AUDIOSONIC 165 166 BANG & OLUFSEN 044 155 BAUR 054 155 156 157 158 BLAUPUNKT 091 098 107 109 129 137 147 BRANDT ELECTRONIQUE 044 045 090 BRAUN 147 BUSH 061 073 121 144 CANON 147 CONDOR 155 CROWN 009 061 144 CROWN/ONWA 148 DAEWOO 009 061 063 064 068 069 144 155 DECCA 039 044 048 148 155 DECCA(UK) 054 DEGRAAF 015 018 039 049 054 148 DUAL 044 090 148 155 DUMONT 015 039 054 148 155 DYNATECH 039 148 ELBE 036 148 ELTA 148 EMERSON 011 032 039 060 062 073 127 148 155 FERGUSON 001 005 044 083 085 090 094 100 104 108 122 130 131 135 138 FINLADIA 015 054 FINLUX 015 018 019 039 044 049 053 054 103 107 143 146 147 148 149 FISHER 015 019 032 FUJITSU 148 FUNAI 039 148 GARANADA(UK) 107 GBC(UK) 054 GOLDSTAR 036 055 148 155 GOODMANS 039 042 050 054 055 061 073 144 148 155 GRAETZ 044 045 090 GRANADA 015 019 049 109 147 149 155 GRANADA(UK) 018 054 GRUNDIG 054 091 098 109 143 HANSEATIC 054 155 HARMAN/KARDON 036 HIFIVOX 044 045 090 HITACHI 018 025 039 044 074 087 090 138 149 IMPERIAL 039 042 096 148 155 INTERFUNK 054 155 INTERVISION 148 155 ITT 015 019 042 044 090 103 ITT-NOKIA 015 019 042 044 045 090 103 149 150 155
40 SETUP CODES
Setup Code Table: VCR (continued)
Maker (Brand) Name Code Number (3 digit) List
JENSEN 044 JVC 044 045 047 085 090 112 135 KARCHER 042 054 155 KENDO 103 KENWOOD 019 044 047 112 KOERTING 155 KUBA 147 148 LLOYD 039 148 LOEWE 065 LOEWE OPTA 054 082 091 109 155 MAGNAVOX 060 062 MARANTZ 036 050 054 073 091 109 MEMOREX 015 019 039 049 055 148 METZ 091 098 109 MINERVA 098 109 MITSUBISHI 047 053 054 076 098 123 154 155 MULTITECH 039 054 098 144 148 155 NATIONAL 107 NEC 036 044 047 090 NECKERMANN 011 019 042 044 054 090 109 127 155 156 157 158 NESCO 148 NOKIA 015 019 042 044 045 090 103 NORDMENDE 039 044 045 047 090 OPTONICA 049 050 ORION 011 032 073 127 148 155 OSAKI 039 055 148 155 OTTO VERSAND 054 098 147 155 156 157 158 PALLADIUM 148 PANASONIC 017 071 088 089 107 129 137 147 148 PATHE' MARCONI 044 045 090 PHILIPS 006 041 043 046 049 050 054 065 079 082 091 109 145 146 155 PIONEER 047 054 113 145 PROLINE 039 148 QUELLE 011 042 044 048 054 055 098 107 109 127 RADIOLA 049 091 109 RCA 060 062 REALISTIC 015 019 039 042 049 050 147 148 REX 044 045 090 ROADSTAR 042 055 148 SABA 009 044 045 047 090 SALORA 019 053 SAMSUNG 009 042 054 056 057 060 062 066 067 092 096 150 155 SANSUI 044 047 SANYO 015 019 073 149 SBR 054 079 082 SCHAUB LORENZ 044 045 090 SCHNEIDER 039 042 049 054 091 096 109 148 155 SEG 042 096 148 SELECO 044 045 090 155 SHARP 049 050 058 075 148 SIEMENS 019 091 098 109 SINGER 155 SONY 039 048 051 052 077 081 156 157 158 SUNSTAR 039 148 SUPERTEC 148 155 SYLVANIA 039 053 148
SETUP CODES 41
Setup Code Table: VCR (continued)
Maker (Brand) Name Code Number (3 digit) List
TANDBERG 032 127 TEAC 039 044 148 TEC 148 155 TECHNICS 107 147 TELEFUNKEN 044 045 090 TELERENT 147 148 TENSAI 148 155 THOMSON 044 045 047 090 THORN 044 085 090 135 THORN-FERGUSON 044 083 085 090 094 100 104 108 130 131 135 149 155 156 157 158 TOSHIBA 009 044 045 053 080 090 153 155 TRANSONIC 155 UHER 042 044 096 ULTRAVOX 155 UNITECH 042 UNIVERSUM 147 148 149 155 156 157 158 WATSON 155 WELTBLICK 155 YAMAHA 036 044 YOKO 042 098 148 155 ZANUSSI 044 045 090 ZENDER 090
Setup Code Table: CBL
Maker (Brand) Name Code Number (3digit) List
BT CABLE 007 CABLETIME 008 011 012 016 CLYDE CABLE VISION 017 DECSAT CANAL 010 FILMNET 018 019 020 FRANCE TELECOM 013 021 GEC 017 JERROLD 001 022 PHILIPS 023 PIONEER 002 SAMSUNG 002 024 SATBOX 004 SCIENTIFIC ATLANTA 005 006 025 026 TELESERVICE 011 TUDI 027 UNITED CABLE 001 VISIOPASS 009 WESTMINSTER CABLE 007
42 INTRODUCTION
Setup Code Table: CD
Maker (Brand) Name Code Number (3 Digit) List
AIWA 072 111 118 156 170 ARCAM 217 221 AKAI 050 177 184 AUDIOMECA 127 221 BSR 044 CALIFORNIA AUDIO 015 109 CAPETRONIC 070 CROWN 042 DENON 187 188 213 FISHER 055 068 FUNAI 126 GOLDSTAR 016 087 GRUNDIG 217 221 225 226 227 228 HAITAI 099 214 HARMAN KARDON 001 002 025 054 190 218 219 HITACHI 093 JVC 176 195 196 KENWOOD 030 062 078 079 148 151 176 178 181 KYOCERA 012 LINN 217 221 LUXMAN 077 102 MAGNAVOX 039 113 MARANTZ 058 084 191 192 193 MBL 184 062 MCINTOSH 194 MITSUBISHI 032 MERIDIAN 217 221 MITSUMI 152 NAD 013 074 197 198 NAKAMICHI 199 200 201 229 NAIM 217 221 NEC 069 ONKYO 037 038 045 046 171 175 202 203 PANASONIC 015 075 109 119 158 183 204 PHILIPS 039 138 149 209 PIONEER 071 094 100 112 123 131 161 162 215 PRIMARE 059 PROTON 210 REALISTIC 058 093 095 104 105 108 164 166 REVOX 127 221 SAMSUNG 028 SANSUI 047 081 157 172 SANYO 033 068 082 095 168 SHARP 058 105 114 151 159 167 180 181 SHERWOOD 003 041 058 105 133 230 231 232 233 234 235 236 237 238 239 240 241 242 243 SIGNATURE 040 SONY 212 103 115 116 118 132 139 163 205 206 207 208 217 T&A 218 222 TEAC 011 058 085 086 106 107 110 121 137 146 154 TECHNICS 244 245 246 247 248 249 250 THETA DIGITAL 039 THOMSON 217 252 THORENS 217 221 TOSHIBA 013 074 097 151 155 173 UNIVERSUM(QUELLE) 217 219 220 221 223 224 YAMAHA 019 031 053 061 135 169
INTRODUCTION 43
Setup Code Table: SAT
Maker (Brand) Name Code Number (3digit) List
AIWA 441 AKAI 333 ALBA 301 411 AMSTRAD 432 ANKARO 421 ASTRO 476 477 478 479 480 481 482 483 BLAUPUNKT 338 390 BUSH 348 406 BUSH(UK) 353 ECHOSTAR 347 FERGUSON 345 348 352 353 363 364 367 406 411 424 FINLUX 309 310 FTE 380 FUBA 314 347 421 GOODMANS 411 GRUNDIG 338 353 367 390 HITACHI 406 411 ITT 367 ITT-NOKIA 367 KATHREIN 301 333 380 390 KOSMOS 380 LOEWE 475 LEMON 474 LORENZEN 461 462 463 464 465 MARANTZ 333 MASPRO 353 406 METZ 390 MINERVA 390 MITSUBISHI 390 MULTISTAR 380 NEC 330 336 346 373 NOKIA 367 NORSAT 346 OTTO VERSAND 390 PACE 348 353 363 364 367 424 PACE MSS SERIES 367 PANASONIC 331 424 PHILIPS 319 332 333 353 421 424 QUADRAL 466 467 468 469 470 471 472 473 QUELLE 390 RADIOLA 353 RADIX 347 SAMSUNG 380 427 432 SAT 427 SCHNEIDER 353 SIEMENS 338 390 SKY MASTER 433 SKYLAB 421 TECHNISAT 328 347 TELECOM 341 TELEFUNKEN 383 THORN-FERGUSON 323 345 348 352 353 363 364 367 VORTEC 432 442 WISI 304 322 326 327 347 427 ZEHNDER 380 427 ZENITH 344
44 SETUP CODES
Setup Code Table: DVD
Maker (Brand) Name Code Number (3 Digit) List
CALIFORNIA AUDIO 040 DENON 002 019 022 034 GE 003 004 GOLDSTAR (LG) 005 HARMAN KARDON 001 032 JVC 006 KENWOOD 007 MAGNAVOX 009 033 MARANTZ 033 MITSUBISHI 023 036 NAD 010 ONKYO 015 PANASONIC 024 025 034 035 PHILIPS 033 PIONEER 012 020 038 041 RUNCO 027 SAMSUNG 031 SANYO 013 SHARP 021 028 SONY 029 TECHNICS 026 THOMSON 003 004 042 TOSHIBA 033 YAMAHA 016 017 030
SETUP CODES 45
Troubleshooting Guide
SYMPTOM CAUSE SOLUTION
Unit does not function when Main • No AC Power • Make certain AC power cord is plugged Power Switch is pushed into a live outlet
• Check to see if outlet is switch controlled
Display lights, but no sound • Intermittent input connections • Make certain that all input and speaker or picture connections are secure
Mute is on • Press Mute button
• Volume control is down • Turn up volume control
Sound is heard, but Front-Panel • Display brightness is turned off • Follow the instructions in the Display Brightness section Display does not light on page 28 so that the display is set to VFD FULL
No sound from any speaker; • Amplifier is in protection mode • Check speaker-wire connections for shorts at receiver light around power switch is red due to possible short and speaker ends
• Amplifier is in protection mode • Contact your local Harman Kardon service depot due to internal problems
No sound from surround or • Incorrect surround mode • Select a mode other than Stereo center speakers • Incorrect configuration • Check speaker mode
• Stereo or Mono program material • With (analog or digital) Dolby surround modes, the surround
decoder may not create rear-channel information from nonencoded programs
• Speakers not properly connected • Check speaker-wire connections or use test tone
to verify connections (see page 21)
Unit does not respond to • Weak batteries in remote • Change remote batteries remote commands • Wrong device selected • Press the AVR selector
• Remote sensor is obscured • Make certain front-panel sensor is visible to remote or
connect remote sensor
Intermittent buzzing in tuner • Local interference • Move unit or antenna away from computers, fluorescent lights,
motors or other electrical appliances
Letters flash in the Channel Indicator • Digital audio feed paused • Resume play for DVD Display and Digital Audio stops • Check that Digital Signal is fed to the Digital Input selected
Processor Reset
In the rare case where the unit’s operation or the displays seem abnormal, the cause may involve the erratic operation of the system’s memory or microprocessor.
To correct this problem, first unplug the unit from the AC wall outlet and wait at least three min­utes. After the pause,reconnect the AC power cord and check the unit’s operation.If the system still malfunctions, a system reset may clear the problem.
To clear the AVR 2000’s entire system memory including tuner presets, output level settings, delay times and speaker configuration data, first put the unit in Standby by pressing the System
Power Control button Tone Mode
taneously.
The unit will turn on automatically and display the RESET message in the Main
Information Display
have cleared the memory in this manner, it is nec­essary to re-establish all system configuration settings and tuner presets.
6
2
. Next, press the
and the RDS@buttons simul-
X
. Note that once you
NOTE: Resetting the processor will erase any configuration settings you have made for speak­ers, output levels, surround modes, digital input assignments as well as the tuner presets.After a reset the unit will be returned to the factory pre­sets, and all settings for these items must be reentered.
If the system is still operating incorrectly,there may have been an electronic discharge or severe AC line interference that has corrupted the mem­ory or microprocessor.
If these steps do not solve the problem, consult an authorized Harman Kardon service depot.
46 TROUBLESHOOTING GUIDE
Technical Specifications
Audio Section
Stereo Mode Continuous Average Power (FTC)
50 Watts per channel, 20Hz–20kHz, @ < 0.07% THD, both channels driven into 8 ohms
Five-Channel Surround Modes Power Per Individual Channel
Front L&R channels: 40 Watts per channel, @ < 0.07% THD, 20Hz–20kHz into 8 ohms
Center channel: 40 Watts, @ < 0.07% THD, 20Hz–20kHz into 8 ohms
Surround channels: 40 Watts per channel, @ < 0.07% THD, 20Hz–20kHz into 8 ohms
Input Sensitivity/Impedance
Linear (High Level) 200mV/47kohms Signal-to-Noise Ratio (IHF-A) 95dB Surround System Adjacent Channel Separation
Analog Decoding 40dB
(Pro Logic, etc.)
Dolby Digital (AC-3) 55dB
DTS 55dB
Frequency Response
@ 1W (+0dB, –3dB) 10Hz– 100kHz High Instantaneous
Current Capability (HCC) ±25 Amps Transient Intermodulation
Distortion (TIM) Unmeasurable Rise Time 16 µsec Slew Rate 40V/µsec**
FM Tuner Section
Frequency Range 87.5–108MHz Usable Sensitivity IHF 1.3 µV/13.2dBf Signal-to-Noise Ratio Mono/Stereo: 70/65dB (DIN) Distortion Mono/Stereo: 0.15/0.3% Stereo Separation 35dB @ 1kHz Selectivity ±300kHz: 65dB Image Rejection 80dB IF Rejection 90dB
AM Tuner Section
Frequency Range 520–1611kHz Signal-to-Noise Ratio 45dB Usable Sensitivity Loop: 500µV Distortion 1kHz, 50% Mod: 0.8% Selectivity ±9kHz: 30dB
Video Section
Video Format PAL/NTSC Input Level/Impedance 1Vp-p /75 ohms Output Level/Impedance 1Vp-p/75 ohms Video Frequency Response 10Hz–8MHz (–3dB)
General
Power Requirement AC 220-240V/ 50Hz Power Consumption 72W idle, 470W maximum
Dimensions (Max)
Width 440mm Height 167mm Depth 435mm Weight 14.0 kg
Depth measurement includes knobs, buttons and terminal connections. Height measurement includes feet and chassis. All features and specifications are subject to change without notice.
Harman Kardon is a registered trademark, and Power for the digital revolution is a trademark, of Harman International Industries, Inc.
*Manufactured under license from Dolby Laboratories. “Dolby,”“Pro Logic,” “AC-3” and the Double-D symbol are trademarks of Dolby Laboratories.Confidential Unpublished Works. ©1992–1999 Dolby Laboratories, Inc.All rights reserved.
DTS and DTS Surround are trademarks of Digital Theater Systems, Inc.
††
UltraStereo is a trademark of UltraStereo Corp.
VMAx is a trademark of Harman International Industries, Inc., and is an implementation of Cooper Bauck Transaural Stereo under patent license.
Logic 7 is a registered trademark of Lexicon, Inc.
Crystal is a registered trademark of Cirrus Logic Corp.
**Without input anti slewing and output isolation networks.
TECHNICAL SPECIFICATIONS 47
250 Crossways Park Drive,Woodbury, New York 11797 www.harmankardon.com Harman Consumer International: 2, route de Tours, 72500 Château-du-Loir, France © 2000 Harman Kardon, Incorporated Part No.:J90200012400
Loading...