Greenlee’s Battery-powered Pistol Grip Cable Cutters
are hand-held tools intended to cut the following:
• ESG45L: ACSR and guy strand.
• ESG50L: Copper and aluminum cable up to 2"
(50mm) in diameter. This tool is intended to cut most
low- and medium-voltage copper and aluminum cable
found on most job sites.
• ESG55L: ACSR and guy strand.
• ESC85L: Copper and aluminum cable up to 3.3"
(85mm) in diameter. This tool is intended to cut
most low- and medium-voltage stranded copper and
aluminum cable.
• ESC105L and ESG105LU: Copper and aluminum
cable up to 4.13" (105 mm) in diameter. This tool
is intended to cut most low- and medium-voltage
stranded copper and aluminum cable as well as lead
or soft steel armored cable found on job sites.
These tools have a retraction stop feature, which allows
the operator to stop the retraction motion of the ram to
shorten cycle time.
These tools are protected by U.S. Patent No. 6,206,663,
6,276,186, 6,401,515, and 6,718,870.
Safety
Safety is essential in the use and maintenance of
Greenlee tools and equipment. This manual and any
markings on the tool provide information for avoiding
hazards and unsafe practices related to the use of this
tool. Observe all of the safety information provided.
Purpose of this Manual
This manual is intended to familiarize all personnel with
the safe operation and maintenance procedures for the
following Greenlee tools:
ESG45L Battery-powered Cable Cutter
ESG50L Battery-powered Cable Cutter
ESG55L Battery-powered Cable Cutter
ESC85L Battery-powered Cable Cutter
ESC105L Battery-powered Cable Cutter
ESG105LU Battery-powered Cable Cutter
Keep this manual available to all personnel.
Replacement manuals are available upon request at
no charge at www.greenlee.com.
Do not discard this product or throw away!
For recycling information, go to www.greenlee.com.
All specications are nominal and may change as design
improvements occur. Greenlee Textron Inc. shall not be liable for
damages resulting from misapplication or misuse of its products.
GATOR is a registered trademark of Textron Innovations Inc.
KEEP THIS MANUAL
Greenlee / A Textron Company4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
2
Battery-powered Pistol Grip Cable Cutters
IMPORTANT SAFETY INFORMATION
SAFETY
ALERT
SYMBOL
This symbol is used to call your attention to hazards
or unsafe practices which could result in an injury or
property damage. The signal word, dened below,
indicates the severity of the hazard. The message
after the signal word provides information for preventing or avoiding the hazard.
Immediate hazards which, if not avoided, WILL result
in severe injury or death.
Hazards which, if not avoided, COULD result in
severe injury or death.
• Electric shock hazard: The owner of this cutter
must be certain that all users of this tool are trained
in the applicable safety codes and standards
as well as in the safe use of this tool and its
accessories.
• Do not cut cable under tension.
• Use the tool for its intended purpose, which is
cutting cable.
Failure to observe these warnings could result in
severe injury or death.
Wear eye protection when operating
or servicing this tool.
Failure to wear eye protection could
result in serious eye injury from
ying debris or hydraulic oil.
Hazards or unsafe practices which, if not avoided,
MAY result in injury or property damage.
Read and understand all of the
instructions and safety information
in this manual before operating or
servicing this tool.
Failure to observe this warning
could result in severe injury or death.
Electric shock hazard:
This tool is not insulated. When
using this unit near energized
electrical lines, use proper personal
protective equipment.
Failure to observe this warning
could result in severe injury or death.
Skin injection hazard:
Do not use hands to check for oil
leaks. Oil under pressure easily
punctures skin. If injured, seek
medical attention immediately to
remove oil.
Failure to observe this warning
could result in serious injury, gangrene, or death.
Do not use solvents or ammable
liquids to clean the tool body.
Solvents or ammable liquids could
ignite and cause serious injury or
property damage.
Greenlee / A Textron Company4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
3
Battery-powered Pistol Grip Cable Cutters
IMPORTANT SAFETY INFORMATION
Cutting hazard:
• Remove battery before changing
dies, adapters, or jaws.
• Keep hands away from the cutting
head when cutting.
Failure to observe these warnings
could result in severe injury or death.
Do not dispose of batteries in a re. They will vent
fumes and may explode.
Failure to observe this warning could result in severe
injury from harmful fumes or burns from ying
debris.
• Inspect tool and blades before use. Replace any
worn or damaged parts. A damaged or improperly assembled tool can break and strike nearby
personnel.
• Carrying strap is for carrying only, not to be used
to hang or suspend tool.
Failure to observe these warnings could result in
severe injury or death.
Do not allow anything to contact the battery
terminals.
• Do not immerse the batteries in liquid. Liquid may
create a short circuit and damage the battery.
If batteries are immersed, contact your service
center for proper handling.
• Do not place the battery into a pocket, tool pouch,
or tool box with conductive objects. Conductive
objects may create a short circuit and damage the
battery.
• Do not place a battery on moist ground or grass.
Moisture may create a short circuit and damage
the battery.
Failure to observe these precautions may result in
injury or property damage.
• Do not store the battery at more than 122 °F
(50°C) or less than –4 °F (–20 °C). Damage to the
battery can result.
• Do not use another manufacturer’s charger. Other
manufacturers’ chargers may overcharge and
damage the battery.
• Do not attempt to open the battery. It contains no
user-serviceable parts.
Failure to observe these precautions may result in
injury or property damage.
• Do not use this tool for continuous use. After 30 to
40 cycles, allow the tool to cool for 15 minutes.
• Do not secure this tool in a vise. This tool is
designed for hand-held operation.
• This tool may be used in damp or wet environments; however, air-drying is recommended before
use if the tool becomes soaked. Damage may
result when the tool is operated prior to thorough
drying when electrical components are soaked.
• Use this tool for the manufacturer’s intended
purpose only.
Failure to observe these precautions may result in
injury or property damage.
Greenlee / A Textron Company4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
Use all appropriate and applicable personal safety
equipment as required such as safety shoes, hard
hat, and safety glasses. Follow all safety rules and
regulations for the job.
Failure to comply may result in personal injury or
property damage.
Do not perform any service or maintenance other
than as described in this manual. Injury or damage
to the tool may result.
Failure to observe this precaution may result in injury
and property damage.
Note: Keep all decals clean and legible, and replace
when necessary.
4
Loading...
+ 8 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.