Gigabyte GA-F2A58M-DS2 Manual

0 (0)

GA-F2A58M-DS2

User's Manual

Rev. 3001

12ME-F258MS2-3001R

Motherboard

GA-F2A58M-DS2

Motherboard

GA-F2A58M-DS2

Mar. 14, 2014

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

ChangestothespecificationsandfeaturesinthismanualmaybemadebyGIGABYTEwithoutpriornotice.

No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.

In order to assist in the use of this product, carefully read the User's Manual.

For product-related information, check on our website at: http://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS,

drivers, or when looking for technical information. Example:

Table of Contents

GA-F2A58M-DS2 Motherboard Layout............................................................................		4
GA-F2A58M-DS2 Motherboard Block Diagram...............................................................		5
Chapter 1 Hardware Installation......................................................................................		6
1-1	Installation Precautions.....................................................................................	6
1-2	Product Specifications......................................................................................	7
1-3	Installing the APU.............................................................................................	9
1-4	Installing the Memory........................................................................................	9
1-5 Installing an Expansion Card..........................................................................		10
1-6 Setup of the AMD Dual Graphics Configuration.............................................		10
1-7	Back Panel Connectors..................................................................................	10
1-8	Internal Connectors........................................................................................	12
Chapter 2 BIOS Setup...................................................................................................		17
2-1	Startup Screen................................................................................................	17
2-2	M.I.T................................................................................................................	18
2-3	System Information.........................................................................................	21
2-4	BIOS Features................................................................................................	22
2-5	Peripherals......................................................................................................	25
2-6	Power Management........................................................................................	27
2-7	Save & Exit.....................................................................................................	28
Chapter 3 Appendix.......................................................................................................		29
3-1	Configuring SATA Hard Drive(s).....................................................................	29
3-2	Drivers Installation..........................................................................................	32
Regulatory Statements..............................................................................................		33
Contact Us.................................................................................................................		36

- 3 -

GA-F2A58M-DS2 Motherboard Layout

KB_MS

ATX_12V
VGA
DVI
R_USB	CPU_FAN
USB_LAN
AUDIO	BAT
Realtek®
GbE LAN
	PCIEX16
iTE®	PCIEX1
iTE®
Super I/O

PCI

CODEC

COM F_AUDIO

DDR3 2	DDR3 1
Socket FM2+	ATX
	ATX

SATA2

GA-F2A58M-DS2

M_BIOS

AMD A58

B_BIOS

CLR_CMOS

SATA2 0 1

	SYS_FAN			F_USB1
SPDIF	_O	F_	USB2
SPDIF	_O	F_	USB2	F_PANEL

Box Contents

55	GA-F2A58M-DS2 motherboard
55	Motherboard driver disk	55	Two SATA cables
55	User's Manual	55	I/O Shield

*The box contents above are for reference only and the actual items shall depend on the product package you obtain.

-4 -

GA-F2A58M-DS2 Motherboard Block Diagram

1 PCI Express x16

1 PCI Express x1

PCIe CLK

(100 MHz)

x16

PCI Express Bus

Realtek®

GbE LAN

RJ45

LAN

PCI Bus

1 PCI

PCI CLK

(33 MHz)

AMD APU

UMI

AMD A58

CODEC

S/PDIF Out

Line In (Rear Speaker Out)

Line Out (Front Speaker Out)

MIC (Center/Subwoofer Speaker Out)

APU CLK+/- (100 MHz)

DISP CLK+/- (100 MHz)

DDR3 2133/1866/1600/1333 MHz

Dual Channel Memory

DVI-D

D-Sub

8 USB 2.0/1.1

Dual BIOS

4 SATA 3Gb/s

LPC

Bus iTE® COM

Super I/O

PS/2 KB/Mouse

For detailed product information/limitation(s), refer to "1-2 Product Specifications."

- 5 -

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures:

•• Prior to installation, make sure the chassis is suitable for the motherboard.

•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation.

•• Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.

•• When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely.

•• When handling the motherboard, avoid touching any metal leads or connectors.

•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.

•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.

•• Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.

•• Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.

•• Before using the product, please verify that all cables and power connectors of your hardware components are connected.

•• To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.

•• Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.

•• Do not place the computer system on an uneven surface.

•• Do not place the computer system in a high-temperature environment.

•• Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.

•• If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.

- 6 -

1-2 Product Specifications

APU	FM2+ Socket:
	-	AMD A series processors
	-	AMD Athlon™ series processors
	(Go to GIGABYTE's website for the latest CPU support list.)
Chipset	AMD A58

Memory	2 x DDR3 DIMM sockets supporting up to 64 GB of system memory
		* Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical
		memory is installed, the actual memory size displayed will be less than the size of
		the physical memory installed.
		* The maximum 64 GB of system memory can be supported using 16 GB (or above)
		memory modules. GIGABYTE will update the memory support list on the official
		website when the memory modules are available on the market.
	Dual channel memory architecture
	Support for DDR3 2133/1866/1600/1333 MHz memory modules
	Support for AMD Memory Profile (AMP)/Extreme Memory Profile (XMP) memory
	modules
	(Go to GIGABYTE's website for the latest supported memory speeds and memory
	modules.)
Onboard	Integrated Graphics Processor:
Graphics	-	1 x D-Sub port, supporting a maximum resolution of 1920x1200
	-	1 x DVI-D port, supporting a maximum resolution of 2560x1600
		* Support for 2560x1600 resolution requires both a monitor and cable that support
		Dual Link DVI.
		* The DVI-D port does not support D-Sub connection by adapter.
	-	Maximum shared memory of 2 GB

Audio		Realtek® ALC887 codec
	High Definition Audio
		2/4/5.1/7.1-channel
		* To configure 7.1-channel audio, you have to use an HD front panel audio module
		and enable the multi-channel audio feature through the audio driver.
	Support for S/PDIF Out
LAN		Realtek® GbE LAN chip (10/100/1000 Mbit)
Expansion Slots		1 x PCI Express x16 slot, running at x16
		(The PCIEX16 slot conforms to PCI Express 3.0 standard.)

*To support PCI Express 3.0, you must install an FM2+ APU.

1 x PCI Express x1 slot

(The PCI Express x1 slot conforms to PCI Express 2.0 standard.)

1 x PCI slot

Multi-Graphics		Support for AMD Dual Graphics technology
Technology		* Only A series APUs support AMD Dual Graphics.
Storage Interface		Chipset:
		- 4 x SATA 3Gb/s connectors
		- Support for RAID 0, RAID 1, RAID 10, and JBOD
USB		Chipset:
		- 8 x USB 2.0/1.1 ports (4 ports on the back panel, 4 ports available through
		the internal USB headers)

		- 7 -

Internal		1 x 24-pin ATX main power connector
Connectors		1 x 8-pin ATX 12V power connector
	4 x SATA 3Gb/s connectors
	1 x APU fan header
	1 x system fan header
	1 x front panel header
	1 x front panel audio header
	1 x S/PDIF Out header
	2 x USB 2.0/1.1 headers
	1 x serial port header
	1 x Clear CMOS jumper
Back Panel		1 x PS/2 keyboard/mouse port
Connectors		1 x D-Sub port
	1 x DVI-D port
	4 x USB 2.0/1.1 ports
	1 x RJ-45 port
	3 x audio jacks (Line In, Line Out, Mic In)
I/O Controller		iTE® I/O Controller Chip
Hardware		System voltage detection
Monitor		APU/System temperature detection
	APU/System fan speed detection
		APU overheating warning
	APU/System fan fail warning
	APU/System fan speed control

* Whether the fan speed control function is supported will depend on the cooler you install.

BIOS		2 x 64 Mbit flash
		Use of licensed AMI UEFI BIOS

Support for DualBIOS™

PnP 1.0a, DMI 2.7, SM BIOS 2.7, ACPI 2.0

Unique Features		Support for @BIOS
	Support for Q-Flash
	Support for Xpress Install
		Support for EasyTune
		* Available functions in EasyTune may differ by motherboard model.
	Support for Smart Recovery2
	Support for ON/OFF Charge
Bundled		Norton® Internet Security (OEM version)
Software		Norton® Internet Security (OEM version)
Software
Operating		Support for Windows 8.1/8/7 32-bit/64-bit
System		Support for Windows XP 32-bit

* To support Windows XP 32-bit, you must install an AMD FM2 Trinity APU.

- 8 -

Form Factor

Micro ATX Form Factor; 22.6cm x 17.4cm

*GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.

*Please visit the Support & Downloads\Utility page on GIGABYTE's website to check the supported operating system(s) for the software listed in the "Unique Features" and "Bundled Software" columns.

1-3 Installing the APU

Read the following guidelines before you begin to install the APU:

•• Make sure that the motherboard supports the APU.

(Go to GIGABYTE's website for the latest APU support list.)

•• Always turn off the computer and unplug the power cord from the power outlet before installing the APU to prevent hardware damage.

•• Locate the pin one of the APU. The APU cannot be inserted if oriented incorrectly.

•• Apply an even and thin layer of thermal grease on the surface of the APU.

•• Do not turn on the computer if the APU cooler is not installed, otherwise overheating and damage of the APU may occur.

•• Set the APU host frequency in accordance with the APU specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including theAPU, graphics card, memory, hard drive, etc.

Installing the APU

Locate the pin one (denoted by a small triangle) of the APU socket and the APU.

A Small Triangle	FM2+ Socket	A Small Triangle	APU
Marking Denotes Pin		Marking Denotes
One of the Socket		APU Pin One

1-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

•• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

•• Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.

•• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.

Dual Channel Memory Configuration

This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual

Channel memory mode will double the original memory bandwidth.

The two DDR3 memory sockets are divided into two channels and each channel has one memory socket as following:

Channel A: DDR3_2Channel B: DDR3_1

- 9 -

Due to APU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1.Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.

2.When enabling Dual Channel mode with two memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used for optimum performance.

1-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:

•• Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.

•• Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.

1-6 Setup of the AMD Dual Graphics Configuration

A.System Requirements

-- AMD A series processor

-- Windows 8.1/8/7 operating system

-- An AMD Dual Graphics technology-supported motherboard (with the BIOS updated to the latest version) and correct driver (make sure the onboard graphics driver version is Rev. 8.982 or above)

-- An AMD graphics card that supports AMD Dual Graphics technology (for more details, please visit AMD's official website) and correct driver (For an FM2+ APU, please use an AMD R7 200 series graphics card; for an FM2 APU, please use an AMD Radeon™ HD 6000 graphics card.)

B.Installing the Graphics Cards and Configuring BIOS Setup

Step 1:

Observe the steps in "1-5 Installing an Expansion Card" and install an AMD Dual Graphics technology-supported graphics card on the PCIEX16 slot. Plug the monitor cable into the graphics card and start up your computer. Step 2:

Enter BIOS Setup to set the following items under the Peripherals\GFX Configuration menu:

-- Set Integrated Graphics to Force.

-- Set UMA Frame Buffer Size to 512M or above.

Save the settings and exit BIOS Setup. Restart your computer.

C. Configuring the Graphics Card Driver

After installing the graphics card driver in the operating system, go to the AMDVISION Engine Control Center. Browse to Performance\AMD Radeon™ Dual Graphics and ensure the Enable AMD Radeon Dual Graphics check box is selected.

(Note) Make sure the drivers for the Chipset, onboard graphics, and external graphics card are properly installed.

1-7 Back Panel Connectors

PS/2 Keyboard and PS/2 Mouse Port

Usetheupperport(green)toconnectaPS/2mouseandthelowerport(purple)toconnectaPS/2keyboard.

- 10 -

D-Sub Port

The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200

(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports

D-Sub connection to this port.

DVI-D Port (Note)

The DVI-D port conforms to the DVI-D specification and supports a maximum resolution of 2560x1600.

Connect a monitor that supports DVI-D connection to this port. Please note that the actual resolutions supported are dependent on the monitor being used and support for 2560x1600 resolution requires both a monitor and cable that support Dual Link DVI.

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.

Connection/

Connection/Speed LED:

Activity LED:

Speed LED

Activity LED

State

Description

State

Description

Orange

1 Gbps data rate

Blinking

Data transmission or receiving is occurring

Green

100 Mbps data rate

Off

No data transmission or receiving is occurring

Off

10 Mbps data rate

LAN Port

Line In Jack (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out Jack (Green)

The line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.

Mic In Jack (Pink)

The Mic in jack. Microphones must be connected to this jack.

To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.

•• When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.

•• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.

(Note) The DVI-D port does not support D-Sub connection by adapter.

- 11 -

+ 25 hidden pages