General Semiconductor ZGL41-170, ZGL41-190, ZGL41-200, ZGL41-100, ZGL41-110 Datasheet

ZGL41-100 THRU ZGL41-200A

SURFACE MOUNT GLASS PASSIVATED ZENER

Zener Voltage - 100 to 200 Volts Steady State Power - 1.0 Watt

FEATURES

♦ Plastic package has Underwriters Laboratory

Flammability Classification 94V-0

♦ For surface mount applications
♦ Glass passivated junction
♦ Low Zener impedance
♦ Low regulation factor
♦ High temperature soldering guaranteed:

250°C/10 seconds at terminals

MECHANICAL DATA

Case: JEDEC DO-213AB molded plastic body over

passivated junction
Terminals: Solder plated solderable per MIL-STD-750,
Method 2026
Polarity: Red band denotes Zener diode and positive end
(cathode)

Mounting Position: Any
Weight: 0.0046 ounce, 0.116 grams

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Ratings at 25°C ambient temperature unless otherwise specified.

OPERATING JUNCTION AND STORAGE TEMPERATURE RANGE: TJ, T

STG

: -55°C to +150°C

NOMINAL MAXIMUM MAXIMUM

ZENER MAXIMUM ZENER DYNAMIC SURGE

INSTANTANEOUS

VOLTAGE IMPEDANCE MAXIMUM DC REVERSE CURRENT FORWARD

at I

ZT

TEST LEAKAGE CURRENT VOLTAGE

TYPE

(NOTE 1)

CURRENT at V

R (NOTE 2)

at 200mA

(V

Z

)(I

ZT

)Z

ZT

at I

ZT

Z

ZK

at I

ZK

(IR)(V

R

)(I

RM

)(V

F

)

(Volts) (mA) (Ohms) (Ohms) (mA) (µA) (Volts) (mAdc) (VOLTS)

ZGL41-100 100 3.7 250 3100 0.25 1.0 76.0 10.0 1.5
ZGL41-110 110 3.4 300 4000 0.25 1.0 83.6 9.1 1.5
ZGL41-120 120 3.1 380 4500 0.25 1.0 91.2 8.3 1.5
ZGL41-130 130 2.9 450 5000 0.25 1.0 98.8 7.7 1.5
ZGL41-140 140 2.7 525 5500 0.25 1.0 106.4 7.1 1.5
ZGL41-150 150 2.5 600 6000 0.25 1.0 114.0 6.7 1.5
ZGL41-160 160 2.3 700 6500 0.25 1.0 121.6 6.3 1.5
ZGL41-170 170 2.2 800 6750 0.25 1.0 129.2 5.9 1.5
ZGL41-180 180 2.1 900 7000 0.25 1.0 136.9 5.6 1.5
ZGL41-190 190 2.0 1050 7500 0.25 1.0 144.4 5.3 1.5
ZGL41-200 200 1.9 1200 8000 0.25 1.0 152.0 5.0 1.5

NOTES:

(1) Standard voltage tolerance is ± 10%, Suffix A= ± 5%
(2) Surge current is a non-repetitive, 8.3ms pulse width square wave or

equivalent sine-wave superimposed on I

ZT

per JEDEC Method

(3) Maximum steady state power dissipation is 1.0 watt at T

T

=75°C

SOLDERABLE ENDS

1st BAND

0.022 (0.56)

0.018 (0.46)

0.205 (5.2)

0.185(4.7)

D1=

0.105

0.095
(2.67)
(2.41)

D2 = D1

+ 0

- 0.008 (0.20)

1st band denotes type and positive end (cathode)

D2

Dimensions in inches and (millimeters)

DO-213AB

8/26/98

RATINGS AND CHARACTERISTIC CURVES ZGL41-100 THRU ZGL41-200A

FIG. 1 - MAXIMUM CONTINUOUS

POWER DISSIPATION

TERMINALS TEMPERATURE, °C

P

M(AV)

, AVERAGE POWER DISSIPATION,

WATTS

FIG. 2 - TYPICAL ZENER IMPEDANCE

I

ZT,

ZENER TEST CURRENT, mA

Z

Z

, DYNAMIC ZENER IMPEDANCE,

OHMS

FIG. 3 - TYPICAL INSTANTANEOUS

FORWARD CHARACTERISTICS

FIG. 4 - TYPICAL REVERSE CHARACTERISTICS

INSTANTANEOUS FORWARD CURRENT,

AMPERES

INSTANTANEOUS REVERSE CURRENT,

MICROAMPERES

INSTANTANEOUS FORWARD VOLTAGE,

VOLTS

FIG. 5 - TYPICAL TEMPERATURE COEFFICIENTS

ØV

Z

, TEMPERATURE COEFFICIENT,

mV/°C

VZ,ZENER VOLTAGE, VOLTS

TJ=25°C

TJ=25°C

PULSE WIDTH=300µs
1% DUTY CYCLE

TESTED at RATED I

ZT

PERCENT OF RATED ZENER VOLTAGE, %

TJ=100°C

P.C.B. MOUNTED ON

0.31 X 0.31 0.08” (8 x 8 x 2mm)
COPPER AREAS PADS

60 H

Z

RESISTIVE OR
INDUCTIVE LOAD

TJ=25°C
I

Z

ma +/- 0.1 IZ(dc)

VZ=180V
VZ=150V

VZ=100V

VZ=200V

VZ, ZENER VOLTAGE, VOLTS

I

ZT

, TEST ZENER CURRENT, mA

FIG. 6 - TYPICAL ZENER VOLTAGE

8/26/98

1.0

0.75

0.5

0.25

0

25 50 75 100 125 150 175

10

1

10,000

1,000

100

10

0.5

10

1

0.1

10

100

500

0.1

0.01

0.4 0.6 0.8

1 1.2 1.4 1.6

220
200
180
160
140
120
100

80

100 110 120 130 140 150 160 170 180 190 200

80

100

0.01
0

20

40

60

10

1

0.1
100

150

200

250