GENERAL ELECTRIC PSJC5YGXWV, PSHS6YGXSS, PSHS6TGXSS, PSHS6RGXSS, PSFW3YGXSS User Manual

Refrigerators

Profile Side-by-Side

ge.com

Safety Instructions . . . . . . . . . . .2–4

Operating Instructions

Automatic Icemaker . . . . . . . . . . . . . . .14

Care and Cleaning . . . . . . . . . . . . .16, 17

ClimateKeeper2™ . . . . . . . . . . . . . . . . . . . .6

Crispers and Pans . . . . . . . . . . . . . . . . .13

CustomCool™ . . . . . . . . . . . . . . . . . . . . .7, 8

Ice and Water Dispenser . . . . . . .15, 16

QuickFreeze™ . . . . . . . . . . . . . . . . . . . . . . .9

Quick Ice . . . . . . . . . . . . . . . . . . . . . . . . . .15

Refrigerator Doors . . . . . . . . . . . . . . . . .12

Replacing the Light Bulbs . . . . . . . . . .18

Set Features . . . . . . . . . . . . . . . . . . . . . . . .6

Shelves and Bins . . . . . . . . . . . . . . .10, 11

Temperature Controls . . . . . . . . . . . . . . .5

TurboCool™ . . . . . . . . . . . . . . . . . . . . . . . . .6

Water Filter . . . . . . . . . . . . . . . . . . . . . . . . .9

Installation Instructions

Installing the Refrigerator . . . . . . .28–31 Moving the Refrigerator . . . . . . . .24–27 Preparing to Install

the Refrigerator . . . . . . . . . . . . . . . . . . . .23 Trim Kits and Panels . . . . . . . . . . . .19–22 Water Line Installation . . . . . . . . .32–34

Troubleshooting Tips . . . . . .36–38

Normal Operating Sounds . . . . . . . . . .35

Consumer Support

Consumer Support . . . . . . . .Back Cover

Performance Data Sheet . . . . . . . . . . .41

Product Registration . . . . . . . . . . . .43, 44

State of California Water

Treatment Device Certificate . . . . . . .42

Warranty (Canadian) . . . . . . . . . . . . . . .39

Warranty (U.S.) . . . . . . . . . . . . . . . . . . . .40

Write the model and serial numbers here:

Model # __________________________

Serial # __________________________

Find these numbers on a label inside the refrigerator compartment at the top on the right side.

Owner’s Manual

and Installation

Models 23, 25, 26, 27 and 29

Profile Côte à Côte

Réfrigérateurs

Manuel d’utilisation

et d’installation

La section française commence à la page 46

Profile Lado a Lado

Refrigeradores

Manual del propietario

e instalación

La sección en español empieza en la página 88

200D8074P018 49-60573 09-08 JR

Downloaded from www.Manualslib.com manuals search engine

Operating Instructions Safety Instructions

Installation

Instructions

Consumer Support Troubleshooting Tips

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■This refrigerator must be properly installed and located in accordance with the Installation Instructions before it is used.

■Do not allow children to climb, stand or hang on the shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.

■Do not touch the cold surfaces in the freezer compartment when hands are damp or wet. Skin may stick to these extremely cold surfaces.

■Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

■In refrigerators with automatic icemakers,

avoid contact with the moving parts of the ejector mechanism, or with the heating element located on the bottom of the icemaker. Do not place fingers or hands on the automatic icemaking mechanism while the refrigerator is plugged in.

■Keep fingers out of the “pinch point” areas; clearances between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

■Unplug the refrigerator before cleaning and making repairs.

NOTE: We strongly recommend that any servicing be performed by a qualified individual.

■Non-LCD models: Setting either or both controls to OFF does not remove power to the light circuit.

■LCD models: Turning the cooling system off does not remove power to the light circuit.

■Do not refreeze frozen foods which have thawed completely.

■Always clean the CustomCool™ Tray after thawing food.

2

Downloaded from www.Manualslib.com manuals search engine

ge.com

DANGER! RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE REFRIGERATOR

	Child entrapment and suffocation are not problems	Refrigerants
	of the past. Junked or abandoned refrigerators are	All refrigeration products contain refrigerants,
	still dangerous…even if they will sit for “just a few
		which under federal law must be removed prior
	days.” If you are getting rid of your old refrigerator,
		to product disposal. If you are getting rid of an
	please follow the instructions below to help prevent
		old refrigeration product, check with the company
	accidents.
		handling the disposal about what to do.
	Before You Throw Away Your Old
	Refrigerator or Freezer:

■Take off the doors.

■Leave the shelves in place so that children may not easily climb inside.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

3

Instructions Operating Instructions Safety

Instructions

Installation

Support Consumer Tips Troubleshooting

Downloaded from www.Manualslib.com manuals search engine

Operating Instructions Safety Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

If the outlet is a standard 2-prong outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

Installation	Instructions

Consumer Support Troubleshooting Tips

4

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Downloaded from www.Manualslib.com manuals search engine

About the temperature controls.

ge.com

Not all features are on all models. Your controls will look like one of the following:

LCD models

Non-LCD models

NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not removed during installation, remove it now.

The temperature controls are preset in the factory at 37°F(3°C) for the refrigerator compartment and 0°F (-18°C)for the freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

Refrigerator temperatures can be adjusted between 34°F and 46°F (1°C to 8°C), and the freezer temperatures can be adjusted between –6°F and 8°F (–21°C to –13°C).

To change the Refrigerator temperature: LCD Models:

Access By: Home > Refrigerator

Activate By: Using the arrows to select the desired temperature. You must press ENTER to set the new temperature.

To change the Freezer temperature: Access By: Home > Freezer

Activate By: Using the arrows to select the desired temperature. You must press ENTER to set the new temperature.

Once the desired temperature has been set, the display will return to the HOME screen and show the set temperatures underneath the actual temperature display for several seconds. Several adjustments may be required. Each time you adjust the controls, allow 24 hours for the refrigerator to reach the temperature you have set.

Non-LCDModels:

To change the temperature, press and release the FREEZER TEMP/FRIDGE TEMP pad. The SET light will come on and the display will show the set temperature. To change the temperature, tap either the >or> pad until the desired temperature is displayed.

Once the desired temperature has been set, the temperature display will return to the actual refrigerator and freezer temperatures after 5 seconds. Several adjustments may be required. Each time you adjust the controls, allow 24 hours for the refrigerator to reach the temperature you have set.

The temperature controls can display both the SETtemperature as well as the actual temperature in the refrigerator and freezer.

The actual temperature may vary slightly from the SETtemperature based on usage and operating environment.

Turning the cooling system off:

LCDmodels:Turning the coolingsystemOFFstops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator.

LCD Models:

Access By: Home > Options > Information and Settings > Cooling System Off

To turn the cooling system back on, press the touch screen and press the ON button.

Activate By: Pressing ENTER.

Non-LCD Models:

Press and release the FREEZER TEMP/FRIDGE TEMP pad. Press> to set freezer temperature to 5. The display will show OFF. To turn the unit back on, press the FREEZER TEMP/FRIDGE TEMP pad. Press >to set the freezer and refrigerator temperatures to the preset points of 0°F (-18°C) for the freezer and 37°F (3°C) for the refrigerator.

When the unit is turned back on, it will take up to 24 hours to stabilize.

Performance Air Flow System

The Performance Air Flow System is designed	not affect performance. Although the Air Tower and the Air
to maximize temperature control in the refrigerator and	Tunnel can be removed, doing so will affect temperature
freezer compartments. This unique special feature consists	performance. (For removal instructions, on-line, contact
of the Air Tower along the back wall of the refrigerator and	us at ge.com or call 800.GE.CARES. In Canada, contact us
the Air Tunnel on the bottom portion of the freezer rear wall.	at GEAppliances.ca or call 1.800.561.3344.)
Placing food in front of the louvers on these components will	5

Instructions Operating Instructions Safety

Instructions

Installation

Support Consumer Tips Troubleshooting

Downloaded from www.Manualslib.com manuals search engine

Operating Instructions Safety Instructions

Installation

Instructions

Consumer Support Troubleshooting Tips

About Set Features.

This pad is used to select the following	exit the mode. If no key is pressed, the mode
features: TurboCool, Quick Ice, Door Alarm	will exit and return to displaying features
and Water Filter.	currently set.
Pressing SET FEATURES repeatedly will cycle
through all of the available features and then
About TurboCool.™

How it Works

	TurboCool™ rapidly cools the refrigerator
	compartment in order to more quickly
	cool foods. Use TurboCool when adding
	a large amount of food to the refrigerator
	compartment, putting away foods after they
	have been sitting out at room temperature or
LCD Models Only	when putting away warm leftovers. It can
	also be used if the refrigerator has been
	without power for an extended period.

Once activated, the compressor will turn on immediately and the fans will cycle on and off at high speed as needed for eight hours. The compressor will continue to run until the refrigerator compartment cools

to approximately 34°F (1°C), then it will cycle on and off to maintain this setting. After

8 hours, or if TurboCool is pressed again, the refrigerator compartment will return to the original setting.

About ClimateKeeper2.™ (on some models)

How to Use

LCD Models:

Access By: Home > Options > Refrigerator

Options > TurboCool

Activate By: Pressing ON.

Deactivate By: Pressing OFF.

Non-LCD Models:

Press SET FEATURES. The refrigerator temperature display will show TurboCool and/or TC. Press ON/OFF.

After TurboCool is complete, the refrigerator compartment will return to the original setting.

NOTES:

The refrigerator temperature cannot be changed during TurboCool.

The freezer temperature is not affected during

TurboCool.

When opening the refrigerator door during TurboCool, the fans will continue to run if they have cycled on.

How it Works

The ClimateKeeper2™ is the industry’s most advanced refrigeration system, delivering optimum temperature and humidity performance to keep food garden fresh longer and reduce freezer burn, while maintaining E star-level efficiency.

The ClimateKeeper2 system features two evaporators—one for the refrigerator and one for the freezer.

This provides two separate cooling systems, and separates the airflow between the fresh food and freezer compartments during normal cooling operations.*

This ensures that the humidity levels in

the fresh food compartment are significantly higher than in a conventional system,** allowing fresh produce and other unsealed foods to retain their moisture content and freshness longer. Moisture sensitive foods such as fresh fruit, salads, rice, etc., can now

6 be stored on open shelves without excessive moisture loss. Due to the higher humidity in

the refrigerator, you may on occasion experience fog or small amounts of moisture in the refrigerator compartment. This is normal and may come and go as different food loads and environmental conditions change. Wipe dry with a paper towel if desired.

The separate airflow system minimizes the mixing of air between the two compartments, which reduces fresh food odor transfer to improve the taste of ice.

The ClimateKeeper2 system also reduces the number of defrosting cycles in the freezer evaporator, thereby reducing freezer burn.

*Freezer air is used in the CustomCool feature.

**Testing shows a higher level of humidity in the Fresh Food section in ClimateKeeper2 refrigerators versus conventional units.

Downloaded from www.Manualslib.com manuals search engine

About CustomCool.™(on some models)

ge.com

Non-LCD Models Only

How it Works

The CustomCool™ feature is used to quickly chill items, thaw items or hold the pan at a specific temperature. This feature is a system of dampers, a fan, a temperature thermistor and a heater.

REFRIGERATOR OPTIONS

	CUSTOM COOL		TURBOCOOL
	PAN
	BEVERAGE
	CENTER
	BACK
OR	LCD Models Only

The pan is tightly sealed to prevent temperature fluctuations in the rest of the refrigerator. The controls for this pan are located on the dispenser with the temperature controls.

ExpressThaw™

ExpressChill™

How to Use

Empty the pan. Place the Chill/Thaw tray in the pan. Place the items on the tray and close the pan completely.

LCD Models:

Access by: Home > Options > Refrigerator Options > CustomCool Pan

Non-LCD Models:

For Non-LCD Models:

Tap that feature’s pad until no options are selected and the display is off.

■During ExpressThaw and

ExpressChill, the display on the controls will count down the time in the cycle (on some models).

Select the ExpressThaw™, ExpressChill™ or SelectTemp™ pad. The display and SET light will come on. Tap the pad until the light appears next to the desired setting.

Use the following chart to determine the best setting to use.

■ExpressChill can be set to 15, 30 or 45 minutes. The default is 15 minutes.

■To stop a feature before it is finished:

For LCD Models:

Go into that feature’s menu and press the OFF button.

■After the ExpressThaw cycle is complete, the pan will reset to the MEAT setting (32°F [0°C]) to help preserve thawed items until they are used.

■The displayed actual temperature of the CustomCool pan may vary slightly from the SET temperature based on usage and operating environment.

NOTE: For food safety reasons, it is recommended that foods be wrapped in plastic wrap when using ExpressThaw.

This will help contain meat juices and improve thawing performance.

How to Remove and Replace the Drawer

To remove:

Pull the drawer out to the stop position.

Rotate all four swing locks to the unlock position.

Lift the front of the drawer up and out.

Lock all four swing locks by rotating them to the lock position.

To replace:

Make sure all four swing locks are in the unlock position.

Place the sides of the drawer into
the drawer supports, making sure
the swing locks fit on the drawer slots.	7

Instructions Operating Instructions Safety

Instructions

Installation

Support Consumer Tips Troubleshooting

Downloaded from www.Manualslib.com manuals search engine

Operating Instructions Safety Instructions

Installation

Instructions

Consumer Support Troubleshooting Tips

About CustomCool.™(on some models)

CustomCool™ Chart

NOTE: Results may vary depending on packaging, starting temperature and other food traits.

ExpressThaw™

0.5 Lb. (4 hours)

■Hamburger Patties (0.5 lb)

■Individually Wrapped Filet Mignon (0.5 lb)

1.0 Lb. (6 hours)

■Chicken Breasts (1.0 lb)

■Ground Beef (1.0 lb)

■Steak (1.0 lb)

2.0 Lbs. (10 hours)

■Chicken Breasts (2.0 lbs)

■Ground Beef (2.0 lbs)

■Steak (2.0 lbs)

3.0 Lbs. (12 hours)

■Chicken Breasts (3.0 lbs)

■Ground Beef (3.0 lbs)

■Steak (3.0 lbs)

ExpressChill™

15Minutes

■1 Beverage Can (12 oz)

■2 Small Juice Boxes (6–8 oz each)

30Minutes

■2 to 6 Beverage Cans (12 oz each)

■2 Plastic 20 oz Bottles of Beverage

■4 to 6 Small Juice Boxes (6–8 oz each)

■3 Foil Juice Packets

■Wine (750 ml bottle)

45Minutes

■2 Liter of Beverage

■1/2 Gallon of Juice

■Gelatin–1 package

SelectTemp™

Citrus Setting (43°F [6°C])

■Oranges, Lemons, Limes, Pineapple, Cantaloupe

■Beans, Cucumbers, Tomatoes, Peppers, Eggplant, Squash

Produce Setting (35°F [2°C])

■Strawberries, Raspberries, Kiwifruit, Pears, Cherries, Blackberries, Grapes, Plums, Nectarines, Apples

■Asparagus, Broccoli, Corn, Mushrooms, Spinach, Cauliflower, Kale, Green Onion, Beets, Onions

Meat Setting (32°F [0°C])

■ Raw Meat, Fish and Poultry

How to Use the Beverage Center (LCD models only)

Some CustomCool models feature a beverage center. It is designed to store beverages at colder temperatures. Select this feature if you like to keep extra-chilled refreshments on hand.

Access by: Home > Options > Refrigerator

Options > Beverage Center

Activate by: Pressing ON.

Deactivate by: Pressing OFF.

Dairy Bin

How to Remove and Replace the Beverage Center (LCD models only)

To remove:

Remove dairy bin first. Holding

the bottom of the dairy bin, lift the front straight up, then lift up and out.

Holding left and right side of beverage center, lift straight up and out.

Leave adapter in place.

To replace:

Engage backside of beverage center in molded supports on adapter. Then push down on the sides of the beverage center. The beverage center will lock into place.

Replace dairy bin.

Beverage

Center

Adapter

8

Downloaded from www.Manualslib.com manuals search engine

About QuickFreeze.™(on some models)

ge.com

QuickFreeze Plate

The QuickFreeze plate is only to be used with the QuickFreeze feature. Use QuickFreeze to freeze items faster to enhance food preservation.

How to Use

Place food (wrapped in plastic wrap) on QuickFreeze plate. Turn the feature on via the LCD controls.

Some LCDModels Only:

Access By: Home > Options > Freezer Options

> QuickFreeze

Activate By: Using the arrows to select the time and pressing Enter.

Deactivate By: Pressing OFF.

NOTE: While the QuickFreeze feature is enabled, the actual freezer temperature may drop as low as –3°F (–19°C). This is normal.

About the water filter.

Cartridge

Holder

Place the top of the cartridge up inside the cartridge holder and slowly turn it to the right.

Filter

Bypass

Plug

SmartWater

Water Filter Cartridge

The water filter cartridge is located in

the back upper right corner of the refrigerator compartment.

When to Replace the Filter

LCD Models:

A pop-up screen will appear on the LCD screen to remind you to replace the water filter. You can check the status of the water filter manually.

Access By: Home > Options > Dispenser Options > Reset Water Filter

Non-LCD Models:

There is a replacement indicator light for the water filter cartridge on the dispenser. This light will turn orange to tell you that you need to replace the filter soon.

The filter cartridge should be replaced when the replacement indicator light turns red or if the flow of water to the dispenser or icemaker decreases.

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old one by slowly turning it to the left. Do not pull down on the cartridge. A small amount of water may drip down.

Installing the Filter Cartridge

There is an adapter attached to the top of the new filter cartridge.

The adapter must be removed before installing the cartridge. To remove the adapter, turn it to the left about 1/4 turn.

Fill the replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after installation.

Line up the arrow on the cartridge and

the cartridge holder. Place the top of the new cartridge up inside the holder. Do not push

it up into the holder.

Slowly turn it to the right until the filter cartridge stops. DONOTOVERTIGHTEN.

As you turn the cartridge, it will automatically raise itself into position. The cartridge will rotate about 1/2 turn.

Run water from the dispenser for 5 minutes to clear the system and prevent sputtering.

LCDModels:

Press FILTER REPLACED button to confirm replacement.

Non-LCDModels:

Press the SET FEATURES pad until REPLACE WATER FILTER is lit. Press and hold the

ON/OFF pad for 3 seconds. WATER FILTER IS RESET will show in the window.

NOTE: A newly installed water filter cartridge may cause water to spurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter cartridge is not available.

The dispenser and the icemaker will not operate without the filter or filter bypass plug.

Replacement Filters:

To order additional filter cartridges in the United States, visit our Website, ge.com, or call GE Parts and Accessories, 800.626.2002.

Filter Model MSWF

Customers in Canada should consult the yellow pages for the nearest Mabe Service Center.

9

Instructions Operating Instructions Safety

Instructions

Installation

Support Consumer Tips Troubleshooting

Downloaded from www.Manualslib.com manuals search engine

Operating Instructions Safety Instructions

Installation

Instructions

Consumer Support Troubleshooting Tips

About the shelves and bins.

Not all features are on all models.

Snugger

Refrigerator bin

Freezer tilt-out bin

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Bins

The larger refrigerator door bins and freezer tilt-out door bins are adjustable.

To remove: Lift the front of the bin straight up, then lift up and out.

To replace or relocate: Engage the back side of the bin in the molded supports on the door. Then push down on the front of the bin.

Bin will lock in place.

The snugger helps prevent tipping, spilling or sliding of small items stored on the door shelf. Place a finger on either side of the snugger near the rear and move it back and forth

to fit your needs.

Top Freezer Bins

Do not block

CAUTION:

Be careful when placing items in the top bin. Make sure that items do not block or fall into the ice chute.

Top freezer bin

CAUTION:

Do not block Part must be in place as shown for proper ice

dispensing. Food cannot be stored in this location.

Top freezer bin (on some models)

Press tab and pull shelf forward to remove

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you to reach items stored behind others. The special edges are designed to help prevent spills from dripping to lower shelves.

To remove:

Slide the shelf out until it reaches the stop, then press down on the tab and slide the shelf straight out.

To replace or relocate:

Line the shelf up with the supports and slide it into place. The shelf can be repositioned when the door is at 90° or more. To reposition the shelf, slide the shelf past the stops and angle downward. Slide shelf down to the desired position, line up with the supports and slide into place.

Make sure you push the shelves all the way back in before you close the door.

QuickSpace™ Shelf

This shelf splits in half and slides under itself for storage of tall items on the shelf below.

This shelf can be removed and replaced or relocated just like Slide-Out Spillproof Shelves.

On some models, this shelf cannot be used in the lowest position.

10

Downloaded from www.Manualslib.com manuals search engine

ge.com

Not all features are on all models.

Freezer Baskets

To remove, push the basket all the way to	Make sure you push the baskets all
the back of the freezer. Lift up until the back	the way back in before you close the door.
pins are disengaged. Lift the entire basket up
and pull out.

Slide-Out Freezer Shelves

To remove, slide out to the stop position,	Make sure you push the shelves all the way
lift the front past the stop position and	back in before you close the door.
slide out.

Fixed Freezer Shelves

There are two types of fixed freezer shelves.

To remove this type of shelf:

Lift the shelf up at the left side. Bring the shelf out.

To remove this type of shelf:

Lift up the left side of the shelf and slide it left into the center of the shelf supports.

Rotate the right side of the shelf up and out of the shelf supports.

NOTEFORDISPENSERMODELS: In order to take full advantage of the tilt-out ice bin, only store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

Door Wine/Beverage Rack (on some models)

This rack holds up to 5 cans or one bottle of wine.

The rack hangs from the sides of the dairy bin.

To remove:

Empty the wine/beverage rack.

Holding the bottom of the dairy bin, lift the front straight up, then lift up and out.

To detach the rack from the dairy bin, pull the rack’s side wires out of the holes on each side of the dairy bin.

To replace:

Reattach the rack to the sides of the bin.

Engage the back side of the bin in the molded supports on the door.

Then push down on the front of the bin. The bin will lock into place.

11

Instructions Operating Instructions Safety

Instructions

Installation

Support Consumer Tips Troubleshooting

Downloaded from www.Manualslib.com manuals search engine

Operating Instructions Safety Instructions

Installation

Instructions

Consumer Support Troubleshooting Tips

About the refrigerator doors.

Refrigerator Doors

The refrigerator doors may feel different than the ones you are used to. The special door opening/closing feature makes sure the doors close all the way and are securely sealed.

When opening and closing the door, you will notice a stop position. If the door is opened past this stop point, the door will remain open to allow you to load and unload food more easily. When the door is only partially open, it will automatically close.

The resistance you feel at the stop position will be reduced as the door is loaded with food.

When the door is only partially open, it will automatically close.

Beyond this stop the door will stay open.

Door Alignment

If doors are uneven, adjust the refrigerator door.

Using a 7/16″wrench, turn the door adjusting screw to the right to raise the door, to the left to lower it. (A nylon

plug, imbedded in the threads of the pin, prevents the pin from turning unless

a wrench is used.)

7/16″ Wrench

After one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.

Raise

Screw down the support leg until it touches the floor. This will prevent door misalignment.

12

Support Leg (on some models)

Before moving the refrigerator, you will need to screw up the support leg. Once the unit is relocated, you will need to screw down the support leg again.

Downloaded from www.Manualslib.com manuals search engine

About the crispers and pans.

ge.com

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the bottom of the drawers should be wiped dry.

On some models, the bottom drawer has full extension slides that allow full access to the drawer.

Adjustable Humidity Crispers

H I		L O
		Slide the control all the way to the HI setting	Slide the control all the way to the LO
		to provide high humidity recommended for	setting to provide lower humidity levels
		most vegetables.	recommended for most fruits.

C

O

L

D

C

O

L

D

E

S

T

Convertible Deli Pan

The convertible deli pan has its own cold air duct to allow a stream of cold air from the freezer compartment or fresh food compartment to flow to the pan.

The variable temperature control regulates the air flow from the Climate Keeper Air Tower.

Set the control to the coldest setting to store fresh meats.

Set the control to cold to convert the pan to normal refrigerator temperature and provide extra vegetable storage space. The cold air duct is turned off. Variable settings between these extremes can

be selected.

About crisper removal.

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling the drawer straight out and lifting the drawer up and over the stop location.

If the door prevents you from taking out

the drawers, first try to remove the door bins. If this does not offer enough clearance,

the refrigerator will need to be rolled forward until the door opens enough to slide the drawers out. In some cases, when you roll the refrigerator out, you will need to move the refrigerator to the left or right as you

roll it out.

13

Instructions Operating Instructions Safety

Instructions

Installation

Support Consumer Tips Troubleshooting

Downloaded from www.Manualslib.com manuals search engine

Operating Instructions Safety Instructions

Installation

Instructions

Consumer Support Troubleshooting Tips

About the automatic icemaker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

On dispenser models, to access ice or reach the power switch:

Lift the bin, then pull it forward until the bin stops.

Lower the bin to access ice or reach the power switch.

NOTE: In order to take full advantage of the tilt-out ice bin, only store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

Automatic Icemaker

The icemaker will produce seven cubes per cycle—approximately 100–130 cubes in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions.

If the refrigerator is operated before the water connection is made to the icemaker, set the power switch in the OFF position.

When the refrigerator has been connected to the water supply, set the power switch to the ON position.

The icemaker will fill with water when it cools to 15°F (–10°C). A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes.

You will hear a buzzing sound each time the icemaker fills with water.

Throw away the first few batches of ice to allow the water line to clear.

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the icemaker will stop producing ice. It is normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink.

Special note about dispenser models:

■Dispenser models have a tilt-out ice bin. The bin can be tilted out as shown in the illustrations, and it will hold itself up

while you take ice out or turn the icemaker power switch on and off. Be sure to put the bin back in place before closing the door.

■To restore your ice level from an empty bucket stage, the following steps are recommended:

12 hours after the first batch of ice has fallen into the bin, dispense

3 to 4 cubes.

After an additional 6 hours, dispense 3 to 4 cubes again.

These steps will restore your ice level in the shortest amount of time.

Icemaker

Power Switch

Feeler Arm

NOTE: In homes with lower-than-average water pressure, you may hear the icemaker cycle multiple times when making one batch of ice.

Lift the bin, then pull it forward until the bin stops.

Removing Ice Bin (dispenser models)

CAUTION:The ice bin is heavy when full.

Set the power switch to the OFF position before removing the bin.

When replacing the bin, be sure to press it firmly into place. If it does not go all the way back, remove it and rotate the drive mechanism 1/4 turn. Then push the bin back again.

Rotate

Drive

Mechanism

Dispenser Models only

Lift and pull forward again to remove the bin.

14

Downloaded from www.Manualslib.com manuals search engine

About the ice and water dispenser. (on some models)				ge.com
		To Use the Dispenser	Dispenser Light
		Select CUBED, CRUSHED or WATER.
		Press the glass gently against the top	The LIGHT pad turns the night light in
		of the dispenser cradle.
			the dispenser on and off. The light also comes on
		The spill shelf is not self-draining. To reduce water
			when the dispenser cradle is pressed. On some
		spotting, the shelf and its grille should be cleaned	models, if this light burns out, it should be replaced
		regularly.	with a 6-watt, 12V maximum bulb.
		If no water is dispensed when the refrigerator is	Door Alarm
		first installed, there may be air in the water line	Use Door Alarm to sound if either door is open
		system. Press the dispenser arm for at least two
		minutes to remove trapped air from the water line	for more than 3 minutes. The alarm will stop
		and to fill the water system. To flush out impurities	once the door is closed. For LCD models, a popup
		in the water line, throw away the first six glassfuls	screen will appear. The alarm can be silenced
Spill Shelf		of water.	by touching the LCD screen.
		CAUTION:Never put fingers or any	LCD Models:
			Access By: Home > Options > Information and
		other objects into the ice crusher discharge
			Settings > Settings > Door Alarm
		opening.
			Access By: Pressing ON.
		Locking the Dispenser
			Deactivate By: Pressing OFF.
		Press the LOCK or LOCK CONTROLS pad for
			Non-LCD Models:
		3 seconds to lock the dispenser and control panel.
		To unlock, press and hold the pad again for	Press the SET FEATURES pad once and DOOR
		3 seconds.	ALARM will blink. Press ON/OFF and the door

alarm will be set and the icon will turn solid. Press ON/OFF again to turn the alarm off.

Quick Ice

When you need to speed up ice production, use the QuickIcefeature. While this feature is turned on, the freezer fan runs continuously for 48 hours, or until the feature is turned OFF. During this period, ice production will increase up to 40%. Models with the integrated ice feature system require at FIRST

USE at least half an 8 oz. glass of ice to be dispensed every 6 to 12 hours. This will help the icemaker fill the bucket properly so that dispensing is better.

How to Use

LCD Models:

Access by: Home > Options > Freezer Options >

Quick Ice

Activate by: Pressing ON.

Deactivate by: Pressing OFF.

Non-LCD Models:

Press the SET FEATURES pad twice and QUICK ICE will blink. Press ON/OFFto turn the feature on, then again to turn it off.

Precise Fill (on some models)

This water dispenser is equipped with a feature called “precise fill.” This feature allows you to choose a precise amount of water (cups or ounces) that you would like dispensed. Pints and Liters are also available for LCD models.

LCD Models

Access By: Home > Options > Dispenser Options > Precise Fill > Set Amount

Activate By: Using the arrow buttons to select the desired amount. Press MORE UNITS to select between CUPS, OUNCES, PINTS or LITERS.

Non-LCD Models

Press the PRECISE FILL CUPS/OZ pad. The WATER pad will light and the CRUSHED

and CUBED ice pads will turn off. The last unit used will be displayed.

Press the PRECISE FILL pad again to toggle between cups and ounces.

If you selectedOUNCES, press the>or >pad to select the number of ounces you would like to have dispensed between 2–99 ounces.

The default is 8 ounces.

If you selectedCUPS, press the>or >pad to select the amount you would like to have

dispensed. They are displayed as 1/4, 1/3, 1/2, 2/3 and 3/4, with the highest amount being 16 3/4 cups. The default is 1 cup.

Press the cup against the cradle and water will begin dispensing. It will automatically stop when the amount set has been dispensed. The display will show the amount of water dispensed, beep, then reset after 5 seconds.

NOTE: Do not leave the dispenser unattended when water is being dispensed.

If you would like to stop dispensing water before the specified amount has been dispensed, just remove the cup from the cradle. The display will show the amount that has been dispensed for 5 seconds. If the cup switch is pressed again within that time, the dispenser will continue up to the set amount. If not, the display will return to the set amount.

15

Instructions Operating Instructions Safety

Instructions

Installation

Support Consumer Tips Troubleshooting

Downloaded from www.Manualslib.com manuals search engine

Operating Instructions Safety Instructions

Installation

Instructions

Consumer Support Troubleshooting Tips

About the ice and water dispenser. (on some models)

Important Facts About Your Dispenser

■Do not add ice from trays or bags to the storage drawer. It may not crush or dispense well.

■Avoid overfilling glass with ice and use of narrow glasses. Backed-up ice can jam the chute or cause the door in the chute to freeze shut . If ice is blocking the chute, poke it through with a wooden spoon.

■Beverages and foods should not be quick-chilled in the ice storage drawer. Cans, bottles or food packages in the storage drawer may cause the icemaker or auger to jam.

■To keep dispensed ice from missing the glass, put the glass close to, but not touching, the dispenser opening.

Care and cleaning of the refrigerator.

■Some crushed ice may be dispensed even though you selected CUBED. This happens occasionally when a few cubes accidentally get directed to

the crusher.

■After crushed ice is dispensed, some water may drip from the chute.

■Sometimes a small mound of snow will form on the door in the ice chute. This condition is normal and usually occurs when you have dispensed crushed ice repeatedly. The snow will eventually evaporate.

Dispenser drip area.

Cleaning the Outside

The dispenser drip area, beneath the grille, should be wiped dry. Water left in this area may leave deposits. Remove the deposits

by adding undiluted vinegar to the well. Soak until the deposits disappear or become loose enough to rinse away.

The dispenser cradle. Before cleaning, lock the dispenser by pressing and holding the LOCK or LOCK CONTROLS pad for

3 seconds. Clean with warm water and baking soda solution—about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. Rinse thoroughly and wipe dry.

The door handles and trim. Clean with a cloth dampened with soapy water. Dry with a soft cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with a commercially available stainless steel

cleaner. A spray-on stainless steel cleaner works best.

Do not use appliance wax or polish on the stainless steel.

Keep the outside clean. Wipe with a clean cloth lightly dampened with kitchen appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may leave a residue that can erode the paint. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch

and weaken the paint finish.

	Cleaning the Inside
	To help prevent odors, leave an open box
	of baking soda in the fresh food and freezer
	compartments.
	Unplug the refrigerator before cleaning.
	If this is not practical, wring excess moisture
	out of sponge or cloth when cleaning around
	switches, lights or controls.
	Use warm water and baking soda solution—
	about a tablespoon (15 ml) of baking soda to
	a quart (1 liter) of water. This both cleans and
	neutralizes odors. Rinse and wipe dry.
16	Use of any cleaning solution other than
	that which is recommended, especially

those that contain petroleum distillates, can crack or damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot water because the extreme

temperature difference may cause them to break. Handle glass shelves carefully. Bumping tempered glass can cause it to shatter.

Do not wash any plastic refrigerator parts in the dishwasher.

The chill/thaw tray is dishwasher safe.

Downloaded from www.Manualslib.com manuals search engine

ge.com

Behind the Refrigerator

Be careful when moving the refrigerator away from the wall. All types of floor coverings can be damaged, particularly cushioned coverings and those with embossed surfaces.

Pull the refrigerator straight out and return it to position by pushing it straight in. Moving the refrigerator in a side direction may result in damage to the floor covering or refrigerator.

When pushing the refrigerator back, make sure you don’t roll over the power cord or icemaker supply line.

Preparing for Vacation

For long vacations or absences, remove food and unplug the refrigerator. Clean the interior with a baking soda solution of

one tablespoon (15 ml) of baking soda to one quart (1 liter) of water. Leave the doors open.

Set the icemaker power switch to the OFF position and shut off the water supply to the refrigerator.

If the temperature can drop below freezing, have a qualified servicer drain the water supply system to prevent serious property damage due to flooding.

Preparing to Move

Secure all loose items such as shelves and drawers by taping them securely in place to prevent damage.

When using a hand truck to move

the refrigerator, do not rest the front or back of the refrigerator against the hand truck. This could damage the refrigerator. Handle only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright position during moving.

17

Instructions Operating Instructions Safety

Instructions

Installation

Support Consumer Tips Troubleshooting

Downloaded from www.Manualslib.com manuals search engine

Operating Instructions Safety Instructions

Installation

Instructions

Consumer Support Troubleshooting Tips

Replacing the light bulbs.

Setting the controls to OFF does not remove power to the light circuit.

Not all features are on all models.

Your light shield will look like one of the following:

Tabs

OR

Pocket

Refrigerator Compartment—Upper Light

Unplug the refrigerator.

The bulbs are located at the top of

the compartment, inside the light shield. On some models, a screw at the front of the light shield will have to be removed.

On other models, the screw is located in the pocket located at the back of the light shield.

To remove the light shield, on some models, press in on the tabs on the sides of the shield and slide forward and out. On other models, just slide the shield forward and out.

After replacing the bulb with an appliance bulb of the same or lower wattage, replace the light shield and screws (on some models). When replacing the light shield, make sure that the tabs at the back of the shield fit into the slots at the back of the light shield housing.

Plug the refrigerator back in.

Refrigerator Compartment—Lower Light

This light is located above the top drawer.

Unplug the refrigerator.

Remove the convertible meat drawer control knob by pulling straight out.

Lift the light shield up and pull it out.

After replacing the bulb with an appliance bulb of the same or lower wattage, replace the shield and

the knob.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just above the light shield. (The shelf will be easier to remove if it is emptied first.) On some models, a screw at the top of the light shield will need to be removed.

To remove the light shield, press in on the sides, and lift up and out.

Replace the bulb with an appliance bulb of the same or lower wattage, and reinstall the light shield. When reinstalling the light shield, make sure the top tabs snap securely into place. Replace the screw (on some models).

Reinstall the shelf and plug the refrigerator back in.

	Dispenser (on some models)
	Unplug the refrigerator.	Replace the bulb with a bulb of
	The bulb is located on the dispenser	the same size and wattage.
	under the control panel. Remove the light	Plug the refrigerator back in.
	bulb by turning it counterclockwise.
	Refrigerator Compartment (LCD models only)
	There is an LED lighting display in the top
LED Lighting	of the refrigerator compartment in LCD
	models. If this assembly needs to be

Display	replaced, call GE Service at 1.800.432.2737
	in the United States or 1.800.561.3344
	in Canada.

18

Downloaded from www.Manualslib.com manuals search engine

Trim kits and decorator panels.

For CustomStyle™ models

Read these instructions completely and carefully.

Before You Begin

Some models are equipped with trim kits that allow you to install door panels. You can order pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories, 800.626.2002, or you can add wood panels to match your kitchen cabinets.

Panels less than 1/4″ (6 mm) thick

When installing wood panels less than 1/4″ (6 mm) thick, you need to create a filler panel, such as 1/8″(3 mm) cardboard, that will fit between the face of the door and the wood panel. If you are installing the pre-cut decorator panels, pre-cut filler panels are included in the kit. The combined thickness of the decorator

or wood panel and the filler panel should be 1/4″ (6 mm).

Panels 1/4″thick or less

1/4″max

3/4″ (19 mm) or Raised Panel

A raised panel design screwed or glued to a 1/4″ (6 mm) thick backing, or a 3/4″ (19 mm) routed board can be used. The raised portion of the panel must be fabricated to permit clearances of at least 2″ (5.1 cm) from the handle side for fingertip clearance.

Panels thicker than 1/4″ (6 mm), up to 3/4″ (19 mm) max, will require that the outer 5/16″ (8 mm) of panel perimeter be no thicker than 1/4″ (6 mm).

Weight limitations for custom panels:

Fresh Food 38 lbs. (17 kg) max.

Freezer Door 28 lbs. (13 kg) max.

Panels thicker than 1/4″(6 mm)

1/4″(6 mm) Thick Backing

5/16″(8 mm)

1/4″(6 mm) max

3/4″(19 mm)

2″(5.1 cm) Clearance

Handle Side

3/4″ (19 mm)

	Appearance	Refrigerator
	Panel
		Door

19

Instructions Operating Instructions Safety

Instructions	Installation

Support Consumer Tips Troubleshooting

Downloaded from www.Manualslib.com manuals search engine

Operating Instructions Safety Instructions

Installation	Instructions

Consumer Support Troubleshooting Tips

Trim kits and decorator panels.

23‘ Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels.

Freezer Panel

Freezer Panel

Without Dispenser

With Dispenser

Fresh Food Panel

Cutout

1/8″ (3 mm)

Cutout

1/8″ (3 mm)

1/8″ (3 mm)

Cutout

5/16″

(8 mm)

5/16″

5/16″

(8 mm)

(8 mm)

177⁄8″

(45.4 cm)

679⁄32″

679⁄32″

(170.9 cm)

(170.9 cm)

FRONT

FRONT

FRONT

1415⁄32″

1415⁄32″

1915⁄32″

(36.8 cm)

(36.8 cm)

(49.5 cm)

335⁄8″

(85.4 cm)

25‘ CustomStyle™ Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels.

Freezer Panel

Freezer Panel

Without Dispenser

With Dispenser

Fresh Food Panel

Cutout

1/8″ (3 mm)

Cutout

1/8″ (3 mm)

1/8″ (3 mm)

Cutout

5/16″

(8 mm)

5/16″

5/16″

(8 mm)

(8 mm)

17″

(43.2 cm)

69″

69″

(175.3 cm)

(175.3 cm)

FRONT

FRONT

FRONT

1415⁄32″

1415⁄32″

1915⁄32″

(36.8 cm)

(36.8 cm)

(49.5 cm)

361⁄4″

(92.0 cm)

20

Downloaded from www.Manualslib.com manuals search engine

Inserting the door panels.

Read these instructions completely and carefully.

Insert the Freezer Panel and Fresh Food Panel.

Carefully push the freezer panel in until it slides	If your model has a dispenser, this step only
into the slot behind the door handle. Push the filler	applies to the fresh food panel and top freezer panel.
panel (required with some door panels) in behind
the decorator panel. Repeat for fresh food panel.

Insert the Bottom Freezer Panel (on dispenser models).

Carefully push the panel in until it slides into the slot behind the door handle. Push the filler panel (required with some door panels) in behind the decorator panel.

Attach the Top Trim on the Freezer and Fresh Food Doors.

The Top Trim can be found inside the refrigerator	door. Hand tighten only. Make sure that the top of
compartment.	each panel fits snugly behind the lip of the Top Trim.
With a T-20 Torxdriver, attach the Top Trim, using two
screws on each Top Trim piece, to the top of each

Top Trim Screws

Cutout

Top Trim Screws

Cutout

Top

Freezer

Panel

Fresh

Food

Panel

Bottom

Freezer

Panel

Side Trim

Side Trim

21

Instructions Operating Instructions Safety

Instructions	Installation

Support Consumer Tips Troubleshooting

Downloaded from www.Manualslib.com manuals search engine

Operating Instructions Safety Instructions

Installation	Instructions

Consumer Support Troubleshooting Tips

Inserting the door panels.

Install the Side Trim.

These pieces are tucked inside the refrigerator door handle.

Do not remove the protective film on the outside of the Side Trim until the Side Trim is installed.

Fit the bottom of the Side Trim under the Bottom Trim as illustrated.

Hold the Side Trim against the front face of

the decorator panels and fit the Side Trim under the Top Trim. Make sure the magnetically attached

Side Trim is fitted correctly and that you are satisfied with the appearance of all the parts.

Top Trim

Side

Trim

Side

Trim

Bottom Trim

22

Downloaded from www.Manualslib.com manuals search engine

Installation	Refrigerator
Instructions	Models 23, 25, 26, 27 and 29

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

In Canada, call 1.800.561.3344 or Visit our Website at: GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT — Save these instructions for local inspector’s use.

• IMPORTANT — Observe all governing codes and ordinances.

•Note to Installer – Be sure to leave these instructions with the Consumer.

•Note to Consumer – Keep these instructions for future reference.

•Skill level – Installation of this appliance requires basic mechanical skills.

•Completion time – Refrigerator Installation

30 minutes

Water Line Installation

30minutes

•Proper installation is the responsibility of the installer.

•Product failure due to improper installation is not covered under the Warranty.

If the refrigerator has already been installed, remove the base grille (see Step 2 in Moving the Refrigerator), then skip to Step 5 in Installing the Refrigerator.

PREPARATION

WATER SUPPLY TO THE ICEMAKER

If the refrigerator has an icemaker, it will have to be connected to a cold water line. A GE water

supply kit (containing tubing, shut-off valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at ge.com (in Canada at GEAppliances.ca) or from Parts and Accessories, 800.626.2002 (in Canada 1.888.261.3055).

TOOLS YOU WILL NEED
3/8″ and 5/16″ Socket	1/2″ and 7/16″ Wrench
1/8″ Hex Wrench
	Plastic Putty Knife
Phillips-Head Screwdriver

23

Downloaded from www.Manualslib.com manuals search engine

Installation Instructions

MOVING THE REFRIGERATOR

1LOADING THE RERIGERATOR ONTO A HAND TRUCK

Leave all tape and door pads on doors until the refrigerator is in its final location.

To move the refrigerator, use a padded hand truck. Center the refrigerator on the hand truck and secure the strap around the refrigerator.

DO NOT OVERTIGHTEN THE STRAP.

2 REMOVE THE BASE GRILLE

Remove the grille by removing the two Phillipshead screws.

If the refrigerator must go through

any entrance that is less than 38″ wide, the doors must be removed. Proceed

to Step 3.

DO NOT remove the handles.

If all entrances are more than 38″ wide, skip to Installing the Refrigerator.

3DISCONNECT THE WATER COUPLING (on some models)

If the refrigerator has a water dispenser, there is a water line from the cabinet into the bottom hinge on the freezer door that must be disconnected.

To disconnect, push in on the white collar of the coupling and pull out the tubing.

White Collar

Bottom

Freezer

Hinge

24

Downloaded from www.Manualslib.com manuals search engine

Installation Instructions

4DISCONNECT THE POWER COUPLING (on some models)

If the refrigerator has a water dispenser, there is a power line (harness) from the cabinet into the bottom hinge on the freezer door that must be disconnected.

To disconnect, pull apart at the coupling.

Bottom

Freezer

Hinge

5DISCONNECT THE ELECTRICAL CONNECTORS (on some models)

If the refrigerator has a refreshment center, there are electrical connectors (harnesses) from the cabinet into the bottom hinge

on the refrigerator door that must be disconnected.

To disconnect, pull apart each connector.

Bottom

Refrigerator

Hinge

25

6CLOSE THE FREEZER AND REFRIGERATOR DOORS

7 REMOVE THE FREEZER DOOR

ARemove the freezer door top hinge cover

(if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

BRemove the two 5/16″ or 1/8″ hex head screws, then lift the hinge straight up to free the hinge pin.

5/16″ or 1/8″ Hex Head

C Open the freezer door to 90.°

90°

Downloaded from www.Manualslib.com manuals search engine

Installation Instructions

MOVING THE REFRIGERATOR (CONT.)

7 REMOVE THE FREEZER DOOR (cont.)

DAs one person slowly lifts the freezer door up and off the bottom hinge, the second person should carefully guide the water line and power line (harness) through the bottom hinge.

90°

ESet the door on a non-scratching surface with the inside up.

8 REMOVE THE REFRIGERATOR DOOR

ARemove the refrigerator door top hinge cover (if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

8REMOVE THE REFRIGERATOR DOOR (cont.)

BRemove the two 5/16″ or 1/8″ hex head screws, then lift the hinge straight up to free the hinge pin.

5/16″ or 1/8″ Hex Head

C Open the refrigerator door to 90.°

90°

26

Downloaded from www.Manualslib.com manuals search engine

Installation Instructions

8

D

E

REMOVE THE REFRIGERATOR DOOR (cont.)

Lift the refrigerator door up and off the bottom hinge.

If the refrigerator has a refreshment center, one person should slowly lift the door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the bottom hinge.

90°

Refreshment Center Models Only

Set the door on a non-scratching surface with the inside up.

9 REPLACING THE DOORS

To replace the doors, simply reverse steps 3 through 8.

However, please note the following:

•When lowering the doors onto the bottom hinges, make sure the second person carefully guides the tube and harnesses through the holes in the hinges.

•When connecting the water line, make sure you insert the tubing all the way to the mark.

Mark

•Do not pinch the tubing and harnesses when placing the doors on the bottom hinges.

•When connecting the power line and the electrical lines (refreshment center models only), be sure that the connectors are seated together fully.

27

Downloaded from www.Manualslib.com manuals search engine

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

•Do not install the refrigerator where

the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

•Do not install the refrigerator where

the temperature will go above 100°F (37°C) because it will not perform properly.

•Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease

of installation, proper air circulation and plumbing and electrical connections:

		23‘ (33” wide),
	23‘/25‘ CustomStyle™	25‘, 26‘, 27‘, 29‘
Sides	1/8″ (4 mm)	1/8″ (4 mm)
Top	1″ (25 mm)	1″ (25 mm)
Back	1/2″ (13 mm)	1″ (25 mm)

DIMENSIONS AND SPECIFICATIONS

	Water	Electrical
	3/4″(19 mm) Airspace
	(1/2″[13 mm] Gap +
24″(61 cm)	1/4″[6 mm] Wall Plates)		25″(63.5 cm)
Cabinet			Countertop

DIMENSIONS AND SPECIFICATIONS (for 23‘ CustomStyle™ models)

701⁄4″(178.4 cm)

36″

(91.4 cm)

24″(61 cm)

DIMENSIONS AND SPECIFICATIONS (for 25‘ CustomStyle™ models)

721⁄4″(183.5 cm)*

36″

(91.4 cm)

24″(61 cm)

*721/4″ (183.5 cm) required for full adjustment of mobility wheels. If cabinets installed above

refrigerator have doors that are flush to the top of the opening for the refrigerator, then an additional 1/8″ may be required to provide clearance for cabinet doors to open freely.

28

Downloaded from www.Manualslib.com manuals search engine

Installation Instructions

1

A

B

CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE (icemaker and dispenser models)

A cold water supply is required for automatic icemaker and dispenser operation. If there

is not a cold water supply, you will need to provide one. See Installing the Water Line section.

NOTES:

•Before making the connection to

the refrigerator, be sure the refrigerator power cord is not plugged into the wall outlet .

•If your refrigerator does not have a water filter, we recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator’s water valve. Install it in the water line near the refrigerator. If using GE SmartConnect™ Refrigerator Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to install filter.

If you are using copper tubing, place a compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supply.

If you are using the GE SmartConnect™ tubing, the nuts are already assembled to the tubing.

If you are using copper tubing, insert the end of the tubing into the refrigerator connection, at the back of the refrigerator,

as far as possible. While holding the tubing, tighten the fitting.

If you are using GE SmartConnect™ tubing, insert the molded end of the tubing into

the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight . Then tighten one additional turn with a wrench. Overtightening may cause leaks.

CFasten the tubing into the clamp provided to hold it in position. You may need to pry open the clamp.

Tubing Clamp	1/4″Tubing

1/4″ Compression Nut

Ferrule (sleeve)

	Refrigerator	SmartConnect™ Tubing
	Connection

2 TURN ON THE WATER SUPPLY

Turn the water on at the shut-off valve (house water supply) and check for any leaks.

3 PLUG IN THE REFRIGERATOR

Before plugging in the refrigerator, make sure the icemaker power switch is set to the OFF position.

See the grounding information attached to the power cord.

29

Downloaded from www.Manualslib.com manuals search engine

Roller Adjusting Screws

Installation Instructions

INSTALLING THE REFRIGERATOR (CONT.)

4 PUT THE REFRIGERATOR IN PLACE

Move the refrigerator to its final location.

5 LEVEL THE REFRIGERATOR

The refrigerator can be leveled by adjusting the rollers located near the bottom hinges.

Raise

Rollers

Rollers have three purposes:

•Rollers adjust so the door closes easily when opened about halfway. (Raise the front about 5/8″ [16 mm] from the floor.)

•Rollers adjust so the refrigerator is firmly positioned on the floor and does not wobble.

•Rollers allow you to move the refrigerator away from the wall for cleaning.

To adjust the rollers on 23‘ (33” wide), 25‘, 26‘, 27‘ and 29‘ models:

•Turn the roller adjusting screws

clockwise to raise the refrigerator, counterclockwise to lower it. Use

a 3/8″ hex socket or wrench, or an adjustable wrench.

5 LEVEL THE REFRIGERATOR (cont.)

To adjust

the rollers on 23‘/25‘

CustomStyle™ models:

Turn the front roller adjusting screws clockwise to raise

the refrigerator, counterclockwise to lower it. Use a 3/8″

hex wrench with extension, or an adjustable wrench.

These models also have rear adjustable rollers so you can align the refrigerator with your kitchen cabinets. Use a 3/8″ hex wrench with extension to turn the screws for the rear rollers— clockwise to raise the refrigerator, counterclockwise to lower it.

6 LEVEL THE DOORS

Adjust the refrigerator door to make the doors even at the top.

To align:

AUsing a 7/16″ wrench, turn the door adjusting screw to the right to raise the door, to the left to lower it .

NOTE:

A nylon plug, imbedded in the threads of the pin, prevents the pin from turning unless a wrench is used.

BAfter one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.

Doors should be even at top

Roller Adjusting Screw

Raise

7/16″ Wrench

30

Downloaded from www.Manualslib.com manuals search engine