Panoptix™ PS21-TM
FrontVü
Installation Instructions
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
chartplotter or fishfinder product box for product warnings and
other important information.
You are responsible for the safe and prudent operation of your
vessel. Sonar is a tool that enhances your awareness of the
water beneath your boat. It does not relieve you of the
responsibility of observing the water around your boat as you
navigate.
CAUTION
Failure to install and maintain this equipment in accordance with
these instructions could result in damage or injury.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
To obtain the best performance and to avoid damage to your
boat, you must install the Garmin® device according to these
instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin Product Support.
• When the transducer moves through the water, bubbles
stream behind the transducer in a “V” shape À. The size and
area of this "V" shape is affected by factors such as your boat
speed and the angle of the transducer mount. You should
mount the transducer in a location that does not introduce air
into the path of propellers Á. Introducing air into the
propellers may severely impact acceleration and top speed
performance, and can damage the propellers and engines.
Mount the transducer far enough to the port or starboard side
away from the propeller(s) to avoid this effect. This effect is
greater if the transducer is aligned vertically with the path of
the propellers. Consider the turning radius of the propellers of
an outboard or stern drive. For most installations, it is not
recommended to mount the transducer between the engines
of a multi-engine arrangement. The transducer is shown from
above.
• When mounted farther from the center of the transom, a
greater deadrise can cause the boat hull À to interfere with
the sonar beam Á, and can cause inconsistent detection on
the opposite side of the boat Â. The transducer is shown
from behind.
Mounting Considerations
This mount is not usable for all boat hulls. Review these
considerations to determine compatibility with your boat type.
Poor transducer location may result in poor transducer
performance or impact the handling of the boat.
• The transducer should not be mounted in a location where it
might be jarred when launching, hauling, or storing.
• The transducer should not be mounted behind strakes, struts,
fittings, water intake or discharge ports, in-hull transducers,
or anything that creates air bubbles or causes the water to
become turbulent. Turbulent water may interfere with the
sonar beam.
• The transducer must be mounted with the transducer face
submerged and facing forward. The transducer shape
requires a larger surface area to be submerged than a typical
transom-mounted transducer. The large submerged surface
area creates drag that can impact the boat's handling and top
speed, ranging from a negligible drag to unacceptable drag.
You may need to adjust your boat's trim tabs if the transducer
is not mounted in the center of the transom. For optimal
results, the transducer should be mounted as close to the
center line as possible.
January 2017
Printed in Taiwan 190-02073-02_0A
Operating Considerations
When operating at speeds greater than 12.9 km/hr (8 mph), the
performance of the transducer is limited, the bottom return is
diminished, and the depth information and alarm may not
provide warnings for potential shallow depth areas.
You should operate your boat slowly in shallow water or in areas
of unknown depth or underwater obstructions.
When enabled, the forward depth alarm sounds in shallow
bottom areas. Suspended or narrow underwater obstructions
may not be identified as the bottom and may not trigger the
alarm. The alarm is not guaranteed to prevent collisions. You
should always use caution when operating your boat.
Effective Forward Range
The transducer has an effective forward range of between five
and eight times the depth of the water. For example, in 3 m
(10 ft.) of water, the effective forward range is between 15 and
24 m (between 50 and 80 ft.). Water conditions and bottom
conditions affect the actual range. You should use caution and
observe the water depth and forward range, especially when
your device is in manual forward range mode.
Software Update
You may need to update the device software when you install
the device or add an accessory to the device.
Loading the New Software on a Memory Card
You must copy the software update to a memory card using a
computer that is running Windows® software.
NOTE: You can contact Garmin customer support to order a
preloaded software update card if you do not have a computer
with Windows software.
Insert a memory card into the card slot on the computer.
1
Go to www.garmin.com/support/software/marine.html.
2
Select Download next to the software bundle that
3
corresponds with your chartplotter.
NOTE: The software download includes updates for all
devices connected to the chartplotter. Select the correct
bundle that corresponds to the chartplotter to be updated.
You can select See All Devices in this Bundle to confirm the
devices included in your download.
Read and agree to the terms.
4
Select Download.
5
If necessary, select Run.
6
If necessary, select the drive associated with the memory
7
card, and select Next > Finish.
Extract the files to the memory card.
8
NOTE: The software update can take several minutes to load
onto the memory card.
Updating the Device Software
Before you can update the software, you must obtain a
software-update memory card or load the latest software onto a
memory card.
Turn on the chartplotter.
1
After the home screen appears, insert the memory card into
2
the card slot.
NOTE: In order for the software update instructions to
appear, the device must be fully booted before the card is
inserted.
Follow the on-screen instructions.
3
Wait several minutes while the software update process
4
completes.
When prompted, leave the memory card in place and restart
5
the chartplotter manually.
Remove the memory card.
6
NOTE: If the memory card is removed before the device
restarts fully, the software update is not complete.
Tools Needed
• Drill
• 3.2 mm (1/8 in.) drill bit
• 4 mm (5/32 in.) drill bit
• #1 Phillips screwdriver
• #2 Phillips screwdriver
• 17 mm hex socket and 17 mm hex wrench
• 7 mm hex wrenches
• Marine sealant
• Cable ties (optional)
Installing the Transducer on a Transom
Aligning the Transom-Mount Hardware on the Boat
Place the transom-mount on the boat transom À 13 mm
1
(1/2 in.) Á from the bottom of the hull.
Insert a shear screw  into the transom-mount bracket in a
2
hole that keeps the housing bracket parallel to the water line
.
Ã
Using the transom-mount bracket as a template, mark the
3
location of the holes.
Remove the bracket.
4
Add the nut to the shear screw and tighten.
5
NOTE: When installed in the bracket, the shear screw and
nut may appear loose.
Tighten the M10 bolt Ä.
6
NOTE: The maximum torque applied to the M10 bolt should
not exceed 51.5 N-m (38 lb-ft.).
Installing the Transom-Mount Hardware on the Boat
If you are installing the bracket on fiberglass, place a piece of
1
tape over the pilot-hole location to reduce cracking of the gel
coat.
Using a 4 mm (5/32 in.) drill bit, drill the pilot holes.
2
Slide the deflection shield bracket À over the transom-mount
3
bracket.
Registering Your Device
Help us better support you by completing our online registration
today.
• Go to my.garmin.com.
• Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Product Support
• Go to www.garmin.com/support for in-country support
information.
• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.
2
Apply marine sealant to the four 5x30 screws, and attach the
4
transom-mount bracket and deflection shield bracket
assembly to the transom using the 5x30 screws and 5 mm
washers.
Mounting the Deflection Shield Cover
+
-
CAUTION
Do not step on the mounted deflection shield.
When you travel at high speeds, your transducer can spray
excessive water onto your motor. You can install the deflection
shield cover to reduce the water spray.
Insert the grommet À into the slot Á of the deflection shield
1
cover Â.
Pull the cable through the grommet.
2
TIP: You can lubricate the grommet and length of cable you
are pulling through the grommet with liquid dish soap.
With the deflection shield cover parallel to the top of the
3
housing bracket Ã, attach the deflection shield cover to the
deflection shield bracket Ä with the screws Å.
Route the cables up the transom above the water line, and
4
secure them with cable ties (optional).
To help make the cable-routing process easier, the locking rings
are packaged separately from the cables. Each locking ring is
packaged in a small bag with a number on the label for easy
identification.
Separate the two halves of the locking ring À.
1
Insert the o-ring Á into the end of the connector.
2
Align the two halves  of the locking ring over the cable and
3
snap them together.
Installation Diagram
Connecting the Transducer to Power and the Garmin Marine Network
WARNING
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
Before you can connect the device to the Garmin Marine
Network and power, you must mount the device.
Route the cables using the appropriate tie wraps, fasteners,
1
and sealant to secure the cables along the route, and through
any bulkheads or the deck.
Install the O-ring and locking collar on the Garmin Marine
2
Network connector.
Connect the bare-wire end of the power cable to a 10 to
3
35 Vdc power source and to the ground (Installation Diagram,
page 3).
Select an option:
4
• Connect the network cable to the network or the Panoptix
port on your chartplotter.
• Connect the network cable to a port on the GMS™ 10, if
available.
Cable Routing Grommets
When routing cables through your boat, it may be necessary to
drill holes to route the cables. Cable routing grommets can be
used to cover cable installation holes. The grommets do not
create a waterproof seal. If necessary, apply a marine sealant
after installation to weatherproof around the grommet and the
cable. You can purchase grommets from your Garmin dealer or
directly from Garmin at www.garmin.com.
Installing Locking Rings on the Cables
Before you install locking rings on the cables, you must route the
cables.
Item Description
À
Á
Â
Chartplotter
Panoptix PS21-TM
Power source (switch is optional)
Maintenance
Cleaning the Transducer
Aquatic fouling accumulates quickly and can reduce your
device's performance.
Remove the fouling with a soft cloth and mild detergent.
1
If the fouling is severe, use a scouring pad or putty knife to
2
remove growth.
Wipe the device dry.
3
Anti-Fouling Paint
To prevent corrosion on metal hulls and to slow the growth of
organisms that can affect a vessel's performance and durability,
you should apply a water-based anti-fouling paint to the hull of
your vessel every six months.
NOTE: Never apply ketone-based anti-fouling paint to your
vessel, because ketones attack many types of plastic and could
damage or destroy your transducer.
Specifications
Specification Measurement
Dimensions (W x H x L) 32 x 118 x 84 mm (1.3 x 4.6 x 3.3 in.)
Transducer weight .39 kg (.87 lb.)
Total weight (transducer, mount,
cable, and deflection shield)
Max. power usage 8 W
2.64 kg (5.82 lb.)
3
Specification Measurement
Operating voltage From 10 to 35 Vdc
Operating temperature range From 0 to 40°C (from 32 to 104°F)
Storage temperature range From -40 to 70°C (from -40 to 158°F)
Material ASA plastic
Maximum range* 91.4 m (300 ft.)
Frequency 417 kHz
Fuse rating 4.0 A mini 32 Vdc
*Dependent upon transducer placement, water salinity, bottom
type, and other water conditions.
© 2017 Garmin Ltd. or its subsidiaries
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries,
registered in the USA and other countries.
subsidiaries. These trademarks may not be used without the express permission of
Garmin.
Panoptix™ is a trademark of Garmin Ltd. or its
© 2017 Garmin Ltd. or its subsidiaries support.garmin.com
Loading...