Page 1
GPSMAP® 4000/5000 Series
owner’s manual
Page 2
© 2008 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street,
Olathe, Kansas 66062, USA
Tel. (913) 397.8200 or (800)
800.1020
Fax (913) 397.8282
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted,
disseminated, downloaded or stored in any storage medium, for any purpose without the express prior written consent of
Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic
storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic
or printed copy of this manual must contain the complete text of this copyright notice and provided further that any
unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its
products and to make changes in the content without obligation to notify any person or organization of such changes or
improvements. Visit the Garmin Web site (www.garmin.com) for current updates and supplemental information concerning
the use and operation of this and other Garmin products.
Garmin® is a trademark of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GPSMAP®,
AutoLocate®, TracBack®, and BlueChart® are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be
used without the express permission of Garmin.
Garmin (Europe) Ltd.
Liberty House
Hounsdown Business Park,
Southampton, Hampshire, SO40 9RB UK
Tel. +44 (0) 870.8501241 (outside the UK)
0808 2380000 (within the UK)
Fax +44 (0) 870.8501251
Garmin Corporation
No. 68, Jangshu 2nd Road,
Shijr, Taipei County, Taiwan
Tel. 886/2.2642.9199
Fax 886/2.2642.9099
WARNING: See the Important Safety and Product Information guide in the product box for
product warnings and other important information.
January 2008 Part Number 190-00854-00 Rev. D Printed in Taiwan
Page 3
Introduction
Introduction
This manual includes information for the following products:
GPSMAP® 4008
•
GPSMAP® 4010
•
GPSMAP® 4012
•
GPSMAP® 5008
•
GPSMAP® 5012
•
GPSMAP® 5015
•
Tips and Shortcuts
Press or touch HOME from any screen to return to the Home screen.
•
Press or touch MENU from any main screen to access additional settings.
•
Press and release the Power key to adjust the display settings.
•
Press and hold the Power key to turn the unit on or off.
•
Manual Conventions
In this manual, when you are instructed to select an item, either press the soft key along the right
side of the screen (GPSMAP 4000 series units) or use your nger to touch that item on the screen
(GPSMAP 5000 series units) to select it. Small arrows (>) in the text indicate that you should select
each item in order. For example, if you see “select Charts > Navigation Chart,” you should press
the Charts soft key (GPSMAP 4000 series) or touch Charts (GPSMAP 5000 series), and then select
or touch Navigation Chart.
Turning the Unit On or Off: page 2.
•
Acquiring GPS Satellite Signals: page 3.
•
Inserting and Removing SD Cards: page 3.
•
Restoring Factory Settings: page 3.
•
Using the Navigation Chart: page 5.
•
Changing the Chart Settings: page 9.
•
Navigating to a Destination: page 18.
•
Creating a Waypoint: page 20.
•
Conguring System Settings: page 29.
•
Using Radar: page 35.
•
Using Sonar: page 39.
•
Alarms and Messages: page 45.
•
Quick Links
GPSMAP® 4000/5000 Series Owner’s Manual i
Page 4
Introduction
Table of Contents
Introduction ................................................i
Tips and Shortcuts .........................................i
Manual Conventions ...................................... i
Quick Links ....................................................i
Getting Started ..........................................1
Unit Overview ...............................................1
Turning the Unit On or Off ............................2
Adjusting the Backlight .................................2
Acquiring GPS Satellite Signals ...................3
Inserting and Removing SD Cards ...............3
Restoring Factory Settings ...........................3
Viewing System Information .........................3
Using the Simulator Mode ............................4
Understanding the Home Screen .................4
Using Charts .............................................5
Using the Navigation Chart ..........................5
Zooming In and Out on the Map .................... 5
Navigation Chart Settings .............................. 5
Understanding Chart Data ............................. 5
Navigating to a Point on the Chart ................. 6
Panning the Navigation Chart ........................ 6
Accessing Additional Object Information ........ 7
Viewing Tide-Station Information.................... 7
Using Mariner’s Eye .....................................8
Mariner’s Eye Settings ................................... 8
Changing the Chart Settings ........................9
Changing the Chart Appearance .................... 9
Using Tracks ...............................................10
Using BlueChart g2 Vision..........................11
Using Mariner’s Eye 3D ..............................12
Mariner’s Eye 3D Settings ............................ 12
Using Fish Eye 3D ......................................13
Fish Eye 3D Settings .................................... 13
Using Fishing Charts ..................................13
Enabling High-Resolution Satellite
Imagery .................................................14
Viewing Aerial Photos .................................15
Viewing Current Station Information ...........15
Detailed Road and POI Data ......................15
Using Automatic Guidance .........................15
Using Combinations ...............................16
Where To? ...............................................18
Navigating to a Destination ........................18
Creating and Using Waypoints ...................20
Creating and Using Routes ........................22
Viewing Information ...............................24
Viewing Tide Station Information ................24
Viewing Current Information .......................24
Viewing Engine Gauges .............................27
Viewing Fuel Gauges .................................27
Viewing Video .............................................28
Conguring the Chartplotter .................29
Conguring System Settings ......................29
Changing Units of Measure ........................29
Conguring Communications Settings .......30
Setting Alarms ............................................30
Setting Navigation Alarms ............................ 31
Setting System Alarms ................................. 31
Setting Sonar Alarms ................................... 31
Conguring My Boat ...................................31
Conguring Other Boats .............................32
Using the Garmin Marine Network ........33
Viewing Connected Garmin Marine
Network Devices ...................................34
Using Radar ............................................35
Understanding the Cruising Screen ...........36
Cruising Screen Settings .............................. 36
Targeting on the Cruising Screen ................. 37
Understanding the Radar Overlay
Screen ...................................................38
Using Sonar ............................................39
Understanding the Full Screen ...................39
Understanding the Split Zoom Screen .......39
Understanding the Split Frequency
Screen ...................................................40
Understanding the Temp Log .....................40
Setting Up Sonar ........................................41
Advanced Sonar Settings ...........................42
Appendix .................................................43
Specications .............................................43
Physical Specications ................................. 43
GPS Performance (with
GPS 17 antenna) .................................... 43
Power ........................................................... 44
NMEA 2000 Specications: .......................... 44
Initializing Unit Settings ..............................44
Calibrating the Touchscreen .......................44
Alarms and Messages ................................45
Product Registration ...................................47
Contact Garmin ..........................................47
Declaration of Conformity (DoC) ................47
Software License Agreement .....................47
NMEA 0183 and NMEA 2000 .....................48
NMEA 0183 .................................................. 48
Approved NMEA 0183 sentences: ............... 48
NMEA 2000 .................................................. 48
Index ........................................................49
Viewing Celestial Information .....................25
Viewing User Data ......................................25
Viewing Other Boats ...................................26
ii GPSMAP® 4000/5000 Series Owner’s Manual
Page 5
Getting Started
Getting Started
Unit Overview
Automatic backlight sensor
GPSMAP 4012
NOTE: Use the soft keys to select menu items on the GPSMAP 4000 Series. Touch menu items on the
GPSMAP 5000 Series screen to select them.
Soft keys
POWER
RANGE (+/-)
ROCKER
MARK
SELECT
MENU
HOME
Numeric keypad
(GPSMAP 4010 and 4012)
SD card slot
Started
GettinG
GPSMAP 5008
POWER
Automatic backlight
sensor
SD card slot
GPSMAP® 4000/5000 Series Owner’s Manual 1
Page 6
Getting Started
NMEA 2000
GettinG
Started
Garmin Marine
connector
Network
connectors
Power
connector
Marine video
connector
NMEA 0183
connector
Turning the Unit On or Off
To turn the unit on, press and release the Power key. When the Warning screen appears, select
I Agree to open the Home screen.
NOTE: The rst time you turn on your unit, you must go through a setup sequence. See page 44.
To turn the unit off, press and hold the Power key.
Warning Screen Home Screen
Adjusting the Backlight
1. Press and release the Power key.
2. Select Backlight.
To allow the unit to automatically adjust the backlight based on ambient light, select Auto.
To manually adjust the backlight,
either select Up or Down, use the
ROCKER (GPSMAP 4000 series),
or touch and drag the brightness
bar (GPSMAP 5000 series).
2 GPSMAP® 4000/5000 Series Owner’s Manual
Page 7
Getting Started
To adjust the color mode:
1. Press and release the Power key.
2. Select Color Mode.
3. Select Day Colors, Night Colors, or Auto.
Acquiring GPS Satellite Signals
When you turn the unit on, the GPS receiver must collect satellite data and establish its current
location. When the unit acquires satellite signals, the signal strength bars at the top of the Home
screen are green . When the unit loses satellite signals, the green bars disappear and the
position icon shows a ashing question mark.
For more information about GPS, visit the Garmin Web site at www.garmin.com/aboutGPS.
Inserting and Removing SD Cards
Your unit supports Secure Digital (SD) cards. Insert optional BlueChart
view high-resolution satellite imagery, and aerial reference photos of ports, harbors, marinas, and
other points of interest. Insert blank SD cards to transfer data such as waypoints, routes, and tracks
to another compatible Garmin unit or a computer. The SD card slot is located on the lower-right
corner of the unit.
To insert the SD card, open the access door and press the SD card in until it clicks. Press the card in
again and release it to eject it from the chartplotter.
®
g2 Vision™ SD cards to
Started
GettinG
Card label
GPSMAP 4010 and 4012
GPSMAP 4008 and 5000 series
Card label
Restoring Factory Settings
You can restore your unit to the original factory settings.
CAUTION: This procedure deletes any information you have entered.
To restore factory settings:
1. From the Home screen, select Congure > System > System Information.
2. Select Factory Settings.
3. Select Reset to restore all factory settings or select Back to cancel.
Viewing System Information
You can view the software version, basemap version, and unit ID number for your chartplotter.
You may need this information to update the system software or to purchase additional map data
information.
From the Home screen, select Congure > System > System Information.
GPSMAP® 4000/5000 Series Owner’s Manual 3
Page 8
Getting Started
Using the Simulator Mode
Simulator Mode turns the GPS receiver off for use indoors or for practice. The unit does not track
satellites in simulator mode.
GettinG
Started
CAUTION: Do not try to navigate using Simulator Mode because the GPS receiver is turned off. Any
satellite signal strength bars shown are only simulations and do not represent the strength of actual
satellite signals.
To turn the Simulator Mode on:
1. From the Home screen, select Congure > System > Simulator > On.
2. Select Setup to set speed, track control, position, simulator time, and simulator date.
Understanding the Home Screen
Use the Home screen to access all other screens. Press or touch HOME from any screen to return to
the Home screen.
NOTE: Options on this screen vary based on the unit type. When you add additional hardware to your
Garmin Marine Network, additional options appear.
GPSMAP 4000 Series Home Screen GPSMAP 5000 Series Home Screen
Charts—access Navigation Chart, Mariner’s Eye, Mariner’s Eye 3D, Fish Eye 3D, Fishing
•
Charts and Radar Overlay (page 5).
NOTE: Mariner’s Eye 3D, Fish Eye 3D, and Fishing Charts are available only if you use a BlueChart
g2 Vision SD card.
Radar—set up and view radar (page 35).
•
Sonar—set up and access sonar information (page 39).
•
Combinations—set up the screen to view a chart, sonar, radar, and video in a two or three
•
(GPSMAP 4000 Series) eld, or four (GPSMAP 5000 Series) eld split screen (page 16).
•
Where To?
Information—view information including tides, currents, celestial data, user data, information
•
—access navigation features (page 18).
about other boats, gauges, and video (page 24).
Congure—access unit and system settings (page 29).
•
Mark—mark, edit, or delete your current location as a waypoint or MOB
•
(GPSMAP 5000 Series).
Man Overboard—navigate to a Man Overboard location (GPSMAP 5000 series).
•
4 GPSMAP® 4000/5000 Series Owner’s Manual
Page 9
Using Charts
Using Charts
Your unit has a basic worldwide imagery map. By purchasing an optional Blue Chart® g2 Vision™
preprogrammed SD card, you can view detailed information for your region, including:
Navigation Chart—displays navigation data, including buoys, lights, cables, depth soundings,
•
marinas, and tide stations in an overhead view.
Mariner’s Eye and Mariner’s Eye 3D—displays a view from above and behind your boat for a
•
visual navigation aid.
Fishing Chart—removes navigational data from the chart and enhances bottom contours for
•
depth recognition.
Fish Eye 3D—an underwater view that visually represents the sea oor according to the
•
information on the chart.
The unit automatically shows relevant navigational data when you select a navigation option.
Using the Navigation Chart
Use the Navigation Chart to plan your course, to view map information, and as a navigational aid.
To access the Navigation Chart, from the Home screen, select Charts > Navigation Chart.
ChartS
USinG
Marine
services
Your boat
Submerged
wreck
Navigation Chart with BlueChart g2 Vision Data
Exposed
wreck
Beacon
Buoy
Zoom scale
Zooming In and Out on the Map
The RANGE (+/-) keys (GPSMAP 4000 series) or the and keys (GPSMAP 5000 series)
control the zoom level, indicated by the scale at the bottom of the navigation chart ( ). The
bar under the number represents that distance on the map.
Navigation Chart Settings
To access additional settings or options for the Navigation chart, press or touch MENU.
Overlay Numbers—show or hide cruising, navigation, shing, and sailing numbers on the screen.
Chart Setup—customize the Navigation chart.
Understanding Chart Data
BlueChart g2 and BlueChart g2 Vision charts use graphic symbols to denote map features, which
follow the standards for US and international charts.
GPSMAP® 4000/5000 Series Owner’s Manual 5
Page 10
Using Charts
Other features common to most charts include depth contour lines (with deep water represented in
white), intertidal zones, spot soundings (as depicted on the original paper chart), navigational aids
and symbols, and obstructions and cable areas.
Navigating to a Point on the Chart
1. From the Home screen, select Charts.
2. Select Navigation Chart, Fishing Chart, or Radar Overlay.
3. Select the point on the chart where you want to go.
USinG
ChartS
4. Select Navigate To.
5. Select Go To (or Guide To when using a preprogrammed BlueChart g2 Vision card for Auto
Guidance).
6. Follow the colored line on the screen to the destination.
To create a route to a point on the chart, see page 22.
Panning the Navigation Chart
Use the ROCKER on your GPSMAP 4000 series unit to move the map pointer ( ) away from
your current location and to scroll to other areas on the navigation chart. As you pan past the edge
of the current map display, the screen scrolls forward to provide continuous map coverage. Touch
and drag the Navigation screen on your GPSMAP 5000 series unit to pan away from your current
location. The position icon ( ) stays at your present location. If the position icon leaves the map
when you pan, a small window appears in the corner so that you can keep track of your current
position.
As you move the map pointer, its coordinates, distance, and bearing from your current location
appear in the upper-left corner of the map.
To pan the map, press up, down, right, or left on the ROCKER (GPSMAP 4000 series), or touch
and drag the Navigation screen (GPSMAP 5000 series).
Pointer
coordinates
Pointer distance
and bearing
from current
location
Map
pointer
Position
window
To stop panning, select Stop Panning.
Pan
options
6 GPSMAP® 4000/5000 Series Owner’s Manual
Page 11
Using Charts
As you pan the map, a list of options appears along the right side. The options change as you move
the map pointer over various objects and charts.
Review—(Review will not appear if the pointer is not near an object—if the pointer is near only
•
one object, the name of the object appears.) This allows you to view details of objects in the
vicinity of the pointer. When you select Review, you are presented with a list of all the objects
near the pointer.
Navigate To—begin navigation to the pointer location.
•
Create Waypoint—mark a waypoint at the pointer location.
•
Information—view tide, current, celestial, or chart information near the pointer location.
•
Accessing Additional Object Information
Use the map pointer ( ) (GPSMAP 4000 series) or touch an item on the screen
(GPSMAP 5000 series) to view information about on-screen map items, waypoints, and charts.
Additional item
information
Selected
item
ChartS
USinG
Viewing Tide-Station Information
Tide-station information appears on the chart with a detailed icon showing the relevant tide level.
You can view an in-depth graph for a tide station to help predict the tide level at different times or on
different days.
Relevant tide
level
Highlight or touch a tide-station icon ( ), and select Review to view a detailed tide graph.
GPSMAP® 4000/5000 Series Owner’s Manual 7
Detailed
tide station
information
Page 12
Using Charts
Using Mariner’s Eye
Mariner’s Eye provides a view from above and behind the boat (according to your course), and
provides a visual navigation aid. This view is helpful when navigating tricky shoals, reefs, bridges,
or channels, and is benecial when trying to identify entry routes and exit routes in unfamiliar
harbors or anchorages.
To access the Mariner’s Eye screen, from the Home screen, select Charts > Mariner’s Eye.
Press the RANGE (+) key (GPSMAP 4000 series) or touch the key (GPSMAP 5000 series) to
USinG
ChartS
move the view closer to your boat and lower to the water. Press the RANGE (-) key (GPSMAP 4000
series) or touch the key (GPSMAP 5000 series) to move the view away from the boat.
Mariner’s Eye Settings
To access additional settings or options from the Mariner’s Eye screen, press MENU.
Rings—toggles the range rings on or off.
Tracks
—turns the visible track log on or off. The chartplotter continues to record tracks if you turn
this setting off, but they are hidden from view.
Safe Depth—adjusts the safe depth for your boat.
Lane Width—adjusts the width of the course line drawn when navigating. This setting also affects
routes (Route To), but does not affect automatic guidance (Guide To).
Show Radar—
If you have a Garmin marine radar device connected to your Garmin Marine
Network, you can overlay radar readings on the Mariner’s Eye screen.
Mariner’s Eye With Radar Information
Overlay Numbers—shows or hides cruising, navigation, shing, and sailing numbers.
8 GPSMAP® 4000/5000 Series Owner’s Manual
Page 13
Using Charts
Changing the Chart Settings
To change chart settings from the Home screen, select Charts > Chart Setup.
Orientation—changes the perspective of the map display:
North Up—sets the top of the map display to a north heading.
•
Track Up—sets the map display to the current track heading.
•
Course Up—sets the map so the direction of navigation is always up. The heading line appears
•
vertically on the screen if shown.
Heading line
Track
Chart border
ChartS
USinG
Heading Line—draws an extension from the bow of the boat in the direction of travel.
Off—turns the heading line off.
•
Distance—sets the distance to the end of the heading line.
•
•
—sets the amount of time until you reach the end of the heading line.
Time
Chart Borders—turns chart borders on when using a BlueChart g2 Vision SD card and you want to
see what area the maps cover.
Tracks
—turns the visible track log on or off. The chartplotter continues to record tracks if you turn
this setting off, but they are hidden from view.
Inset Map—turns the inset map on or off when panning away. Select Auto to turn the inset map on
only when the boat symbol is no longer visible.
Appearance—customizes how items are shown on the map. See “Changing the Chart Appearance”
on page 9.
Changing the Chart Appearance
From the Home screen, select Charts > Chart Setup > Appearance.
Detail—adjusts the amount of detail shown on the map at different zoom levels.
Photos—sets the high-resolution satellite images to off, land only, or blend. High-resolution satellite
imagery is only available while using a BlueChart g2 Vision SD card.
Spot Depths—turns spot soundings on or off and sets a dangerous depth.
Light Sectors—adjusts the drawing of light sectors on the map.
Symbols—selects the navaid symbol set (NOAA or IALA).
Symbol Size—adjusts the size of the symbols shown on the map.
GPSMAP® 4000/5000 Series Owner’s Manual 9
Page 14
Using Charts
Using Tracks
A track is a recording of your path. The track currently being recorded is the active track. An active
track can be saved.
To turn the track log on:
From the Navigation chart, select Menu > Chart Setup > Tracks > On. A trailing line on the chart
indicates your track.
USinG
ChartS
To save the active track:
1. From the Home screen, select Information > User Data > Tracks > Save Active Track.
2. Select either the time the current track began (or Midnight, if shown) or Entire Log.
3. To name the track, change the color of the track, or save it as a route, select Edit Track.
To clear the active track:
From the Home screen, select Information > User Data > Tracks > Clear Active Track. The
track memory is cleared; the current track continues to be recorded.
To retrace the active track:
1. From the Home screen, select Information > User Data > Tracks > Follow Active Track.
2. Select either the time the current track began or Entire Log.
3. Follow the colored line on the screen.
To edit or delete a saved track:
1. From the Home screen, select Information > User Data > Tracks > Saved Tracks.
2. Select the track you want to edit or delete.
10 GPSMAP® 4000/5000 Series Owner’s Manual
Page 15
Using Charts
3. Select Edit Track to change the name or color of the track or select Delete to delete it.
Select Next Page to view the track on the navigation chart.
To set active Track Options:
From the Home screen, select Information > User Data > Tracks > Active Track Options.
Record Mode—select Off, Fill, or Wrap.
Off—does not record a track log.
•
Fill—records a track log until the track memory is full.
•
Wrap—continuously records the track log, replacing the oldest track data with new data.
•
Interval—denes the frequency at which the track plot is recorded. Recording more-frequent plots
is more accurate but lls the track log faster.
Interval—sets whether the interval is determined by distance, time, or resolution. (Select
•
Change to set the quantity.)
Distance—records the track based on a distance between points.
•
•
•
—records the track based on a time interval.
Time
Resolution—records the track plot based on a variance from your course. This setting is
recommended for the most-efcient use of memory. The distance value (Change) is the
maximum error allowed from the true course before recording a track point.
Change—sets the value of the interval.
•
Color—sets the color of the track plot.
ChartS
USinG
Using BlueChart g2 Vision
Optional BlueChart g2 Vision preprogrammed SD cards allow you to get the most out of your unit.
In addition to detailed marine charting, BlueChart g2 Vision has the following features:
Mariner’s Eye 3D—provides a view from above and behind the boat for a three-dimensional
•
navigation aid. The BlueChart g2 Vision Mariner’s Eye 3D is more detailed than the preloaded
data.
Fish Eye 3D— provides an underwater, 3D view that visually represents the sea oor according
•
to the information on the chart.
Fishing Charts—provides a view of the chart with enhanced bottom contours and without
•
navigational data. This chart works well for offshore deep-sea shing.
High Resolution Satellite Imagery— provides high-resolution satellite images for a realistic
•
view of the land and water on the Navigation chart.
Aerial Photos—provides a view of marinas and other navigationally-signicant aerial photos to
•
help you visualize your surroundings.
Detailed Roads and POI data—provides a view of roads, restaurants, and other points of
•
interest (POIs) along the shore.
Current Data—provides a view of current station information.
•
Auto Guidance—uses the chart data and specied boat safe depth to determine the best course to
•
your destination.
NOTE: You cannot transfer BlueChart g2 Vision data from the SD card to your computer for backup or
viewing purposes. You can only use the SD card on BlueChart g2 Vision compatible Garmin GPS units.
GPSMAP® 4000/5000 Series Owner’s Manual 11
Page 16
Using Charts
Using Mariner’s Eye 3D
A BlueChart g2 Vision SD card offers Mariner’s Eye 3D, which provides a detailed threedimensional view from above and behind the boat (according to your course), and provides a visual
navigation aid. This view is helpful when navigating tricky shoals, reefs, bridges, or channels, and is
benecial when trying to identify entry and exit routes in unfamiliar harbors or anchorages.
USinG
ChartS
Mariner’s Eye 3D Navigation Chart
Press the RANGE (+) key (GPSMAP 4000 series) or touch the key (GPSMAP 5000 series) to
move the view closer to your boat and lower to the water. Press the RANGE (-) key (GPSMAP 4000
series) or touch the key (GPSMAP 5000 series) to move the view away from the boat.
Mariner’s Eye 3D Settings
To access additional settings or options from the Mariner’s Eye 3D screen, press MENU.
Colors
—selects between Normal (Default), Water Hazard, and All Hazard. The Normal setting
shows the land as seen from the water. The Water Hazard setting indicates shallow water and land
with a color scale. Blue indicates deep water, yellow is shallow water, and red is very shallow. The
Water Hazard setting indicates land in green and brown, and the All Hazard setting shows land as
dark red.
Mariner’s Eye 3D, Normal Colors Mariner’s Eye 3D, Hazard Colors
Safe Depth—adjusts the depth at which red indicates shallow water. This also changes the global
Safe Depth setting as it applies to the Auto Guidance feature.
Rings, Tracks, Lane Width, and Show Radar—see “Mariner’s Eye Settings” on page 8.
12 GPSMAP® 4000/5000 Series Owner’s Manual
Page 17
Using Charts
Using Fish Eye 3D
Using the depth contour lines of the BlueChart g2 Vision cartography, Fish Eye 3D provides an
underwater view of the sea oor or lake bottom. Use the RANGE keys (GPSMAP 4000 series) or
the and keys (GPSMAP 5000 series) to adjust the view.
Fish Eye 3D
Fish Eye 3D Settings
To access additional settings or options for the Fish Eye 3D screen, press MENU.
ChartS
USinG
Sonar Cone—turns a cone on or off that shows the area covered by your transducer.
Sonar Data—visually shows the sonar readings received by your transducer for the best
combination of sonar and mapping.
Tracks
—turns the track log on or off.
Overlay Numbers—shows or hides cruising, navigation, shing, sailing, or fuel numbers.
Using Fishing Charts
Use the Fishing chart for a detailed, unobstructed view of the bottom contours and depth soundings
on the chart.
Fishing Chart Navigation Chart
The Fishing chart uses detailed bathymetric data on a preprogrammed BlueChart g2 Vision SD card,
and is best for offshore deep-sea shing.
GPSMAP® 4000/5000 Series Owner’s Manual 13
Page 18
Using Charts
Enabling High-Resolution Satellite Imagery
You can overlay high-resolution satellite images on the land, the sea, or both portions of the
Navigation chart when using a preprogrammed BlueChart g2 Vision SD card.
To enable satellite imagery:
1. While viewing the Navigation Chart, press MENU.
2. Select Chart Setup > Appearance > Photos.
3. Select one of the following:
USinG
ChartS
Off—standard chart information is shown on the map.
•
Land Only—standard chart information is shown on water with photos overlaying the land.
•
Blend—photos overlay both the water and the land at a specied opacity. The higher you set
•
the percentage, the more the satellite photos will cover both land and water.
NOTE: When enabled, the high-resolution satellite images are present only at lower zoom levels. If you
cannot see the high-resolution images in your BlueChart g2 Vision region, zoom in using the RANGE
(+) key (GPSMAP 4000 series) or touch the key (GPSMAP 5000 series), or set the detail level
higher.
Photo Overlay Off Land Only Photo Overlay
Blend at 50%
14 GPSMAP® 4000/5000 Series Owner’s Manual
Blend at 100%
Page 19
Using Charts
Viewing Aerial Photos
Preprogrammed BlueChart g2 Vision SD cards contain aerial photographs of many landmarks,
marinas, and harbors. Use these photos to help orient yourself to your surroundings or to acquaint
yourself with a marina or harbor prior to arrival.
NOTE: Use the RANGE (+/-) keys (GPSMAP 4000 series) or touch the and keys (GPSMAP
5000 series) to zoom in and out while viewing the aerial photo on the full screen.
To access aerial photos from the navigation chart:
Use the ROCKER (GPSMAP 4000 series) or touch the screen (GPSMAP 5000 series) to
highlight a camera icon with the pointer, and select Aerial Photo or Review.
ChartS
USinG
Overhead
Perspective
Viewing Current Station Information
If current stations are available in your BlueChart g2 Vision region, they appear on the navigation
chart as highlighted arrows. These detailed icons show the speed and direction of the current at a
glance. Select Review or the name of the station display a current graph.
Detailed Road and POI Data
BlueChart g2 Vision contains detailed road and POI data, which includes highly detailed coastal
roads and points of interest (POIs) such as restaurants, lodging, local attractions, and more. For
instructions on searching for, and navigating to, these POIs, see the “Where To?” section (page 18).
Using Automatic Guidance
Automatic Guidance automatically suggests routes based on available BlueChart g2 Vision chart
information.
GPSMAP® 4000/5000 Series Owner’s Manual 15
Page 20
Using Combinations
Using Combinations
Use the Combinations screen to view a combination of different screens at the same time. The
number of options available on the Combinations screen depends on the optional network devices
you have connected to your chartplotter, and whether you are using an optional BlueChart g2
Vision SD card. You can combine two or three screens (GPSMAP 4000 series) or up to four screens
(GPSMAP 5000 series).
To access the Combinations screen from the Home screen, select Combinations.
USinG
CombinationS
Combinations Screen
The Combinations screen shows a list of possible screen combinations. When viewing three
combination screens, one screen is larger than the others. The charts are numbered with a
corresponding button in the lower-right corner (GPSMAP 4000 series). To switch the larger screen,
select the icon from the lower-right corner that represents the screen you want (GPSMAP 4000
series) or touch Menu > Change Combination (GPSMAP 5000 series). Touch one of the screens
to select a single-screen combination page that will provide congurable data elds (GPSMAP 5000
series).
Data elds
Focus screen
(GPSMAP 4000 series)
Select to switch focus
screen (GPSMAP 4000
series only)
Navigation Chart, Radar, and Sonar Combination
(GPSMAP 4000 series)
To access additional settings or options for the Combinations screen, press MENU.
16 GPSMAP® 4000/5000 Series Owner’s Manual
Page 21
Using Combinations
To customize the screen combinations:
1. While viewing the Combinations screen, select MENU > Change Combination, or, from the
Home screen, select Combinations > Unused Combo (if one is available).
Select the number of
Combination
screen 1
Combination
screen 2
Data bar
combination screens
Change to vertical or
horizontal layout
Toggle the
data bar
Change combination
screen 1
Change combination
screen 2
CombinationS
USinG
2. Select Num Functions to select the number of combination screens, toggle the data bar on or
off, and select the combination screens to view.
3. Select Done.
NOTE: You can only choose from the options available to your unit. To increase the number of screens
available, use a BlueChart g2 Vision SD card or add network devices.
To add additional data elds:
1. While viewing the Combinations screen, press the soft key corresponding to an unused data eld
(GPSMAP 4000 series) or touch an unused data eld (GPSMAP 5000 series) .
New data eld
Adding a Data Field (GPSMAP 4000 series)
2. Select the Digital Item to be displayed on the Combinations Screen. Available options vary, based
on the unit and network conguration.
To edit an existing data eld:
While viewing the Combinations screen, press a soft key corresponding to a data eld (GPSMAP
4000 series) or touch a data eld (GPSMAP 5000 series). Select the item to be displayed.
To change the layout to horizontal or vertical:
1. While viewing the Combinations screen, select MENU > Change Combination.
2. Select Layout Ver. or Layout Horiz.
GPSMAP® 4000/5000 Series Owner’s Manual 17
Page 22
Where To?
Where To?
Use the Where To? option on the Home screen to search for, and navigate to, nearby fuel, repairs,
services, waypoints, and routes.
NOTE: You must create waypoints and routes before you can navigate to them.
You can navigate to a destination using one of three methods: Go To, Route To, or Guide To.
Go To
•
•
•
to?
Where
Navigating to a Destination
You can search for, and navigate to, nearby destinations including fuel, repairs, marinas, waypoints,
and routes.
To begin navigating:
1. From the Home screen, select Where To?.
2. Select the marine service category to which you want to navigate. The unit shows the list of the
—takes you directly to the destination.
Route To—creates a route from your location to a destination, allowing you to add turns to the
route.
Guide To—searches BlueChart g2 Vision chart data to suggest the best path to your destination.
You must be using a BlueChart g2 Vision SD card for this option to appear.
CAUTION: Guide To does not ensure obstacle and bottom clearance. For safety, always resolve any
discrepancies or questions before continuing navigation.
50 nearest locations and the distance and bearing to each.
3. Select the marine service item to which you want to navigate. A screen containing information
about the selected marine service appears.
18 GPSMAP® 4000/5000 Series Owner’s Manual
Page 23
Where To?
NOTE: Select Next Page to view additional information or to display the location on a chart.
4. Select Navigate To.
5. Select Go To.
OR
Select Guide To when using a preprogrammed BlueChart g2 Vision card to use Auto Guidance.
6. Follow the colored line on the screen to the destination.
To stop navigating:
From the Navigation chart, select Menu, and then select Stop Navigating.
Where
to?
To search for a destination by name:
1. From the Home screen, select Where To? > Search by Name.
GPSMAP® 4000/5000 Series Owner’s Manual 19
Page 24
Where To?
2. Use the ROCKER (GPSMAP 4000 series) or touch (GPSMAP 5000 series) to select characters
and spell at least a portion of the name of your destination.
Search - GPSMAP 4000 series Search - GPSMAP 5000 series
3. Select Done to view the 50 nearest destinations that contain your search criteria.
4. Select the best location, then select Navigate To > Go To or Route To or Guide To (when using
to?
Where
a preprogrammed BlueChart g2 Vision card).
Creating and Using Waypoints
You can store up to 1,500 waypoints with a user-dened name, symbol, depth, and water
temperature for each waypoint.
To create a new waypoint:
1. From the Home screen, select Charts > Navigation Chart.
2. Use the map pointer ( ) to select the location you want to designate as a
waypoint (GPSMAP 4000 series); touch the location you want to designate as a waypoint
(GPSMAP 5000 series).
3. Select Create Waypoint.
4. Select one of the following:
Edit Waypoint—designate a specic name, symbol, water depth, water temperature, or
•
position.
Delete—delete the waypoint.
•
Navigate To—go to the waypoint.
•
Back—return to the navigation chart.
•
20 GPSMAP® 4000/5000 Series Owner’s Manual
Page 25
Where To?
To mark your current location as a waypoint:
From any screen, press the MARK key (GPSMAP 4000 series) or touch Mark on the Home
screen (GPSMAP 5000 series)
Edit Waypoint—designates a specic name, symbol, water depth, water temperature, or
•
position.
Delete—deletes the waypoint.
•
Man Overboard—designates the current location as a Man Overboard location.
•
Next Page/Previous Page—switches between waypoint information and the navigation chart.
•
Back—saves the waypoint and returns to the navigation chart.
•
NOTE: Selecting Mark creates a waypoint only at your present location.
To mark an MOB (Man Overboard) location:
When you mark a waypoint, you can designate it as an MOB (Man Overboard). This marks the
point and sets a course back to the marked location. When an MOB is active, an MOB waypoint
with an international MOB symbol is created, and the unit is on an active navigation to that point.
1. At any time, press the MARK key (GPSMAP 4000 series).
2. Select Man Overboard.
On the GPSMAP 5000 series, a Man Overboard button is available on the Home screen.
To edit an existing waypoint:
1. From the Navigation chart, use the map pointer ( ) (GPSMAP 4000 series) or touch the
waypoint (GPSMAP 5000 series) to highlight the waypoint on the navigation chart.
OR
From the Home screen, select Information > User Data > Waypoints.
2. Select the waypoint you want to edit.
Where
to?
3. Select Edit Waypoint.
4. Select the waypoint attribute you want to change (Name, Symbol, Depth, Water Temp, or
Position).
To move the waypoint on the navigation chart:
1. Select the waypoint on the navigation chart.
2. Select Review. (The Review button is only shown when more than one waypoint is in the
vicinity.)
3. Select the button for the waypoint you want to edit.
4. Select Edit Waypoint > Position.
5. Select Use Chart or Enter Coordinates.
GPSMAP® 4000/5000 Series Owner’s Manual 21
Page 26
Where To?
6. If entering coordinates, use the ROCKER (GPSMAP 4000 series) or the keyboard (GPSMAP
5000 series) to enter the new coordinates for the waypoint. If using the chart, highlight the new
location with the map pointer ( ) (GPSMAP 4000 series) or touch the location (GPSMAP 5000
series), and select Move Waypoint. The waypoint moves to the new location.
To view a list of all waypoints:
From the Home screen, select Information > User Data > Waypoints.
To delete a waypoint or MOB:
1. From the Navigation chart, touch the waypoint (GPSMAP 5000 series) or use the map pointer
( ) (GPSMAP 4000 series) to highlight the waypoint on the navigation chart.
OR
From the Home screen, select Information > User Data > Waypoints.
2. Select the waypoint or MOB you want to delete.
3. Select Delete.
Creating and Using Routes
You can create and store up to 20 routes with up to 250 waypoints each.
to?
Where
To create a route from your present location:
1. From the Navigation chart, use the map pointer ( ) (GPSMAP 4000 series) or touch your
destination (GPSMAP 5000 series) to select your destination.
2. Select Navigate To > Route To.
3. Use the map pointer ( ) (GPSMAP 4000 series) to select where you want to make the last turn.
Touch the location where you want to make the last turn toward your destination (GPSMAP 5000
series).
4. Select Add Turn.
22 GPSMAP® 4000/5000 Series Owner’s Manual
Page 27
Where To?
5. To add additional turns, select where you want to make the turn (working backward from the
destination) and select Add Turn.
6. Select Done to nish the route or Cancel Route to delete the route.
To create a route in another location:
1. From the Home screen, select Information > User Data > Routes > New Route.
2. Use the map pointer ( ) (GPSMAP 4000 series) or touch the location (GPSMAP 5000 series) to
select the initial location where you want to start the new route.
3. Select Add Turn to mark the starting point of the route.
4. Choose the location of the rst turn and select Add Turn. Repeat until the route is complete.
5. Select Done.
To create a route using Auto Guidance:
1. From the Navigation chart, select your destination.
2. Select Navigate To > Guide To. Your route is calculated.
NOTE: You can change the auto guidance path to a route by selecting the end of the path and selecting
Navigate To > Route To. The auto guidance path stays on the screen, allowing you to trace it while
creating a route.
To edit a route:
1. From the Home screen, select Information > User Data > Routes.
2. Select the route to edit.
3. Select Edit Route. You can edit the route name, edit the route turns, or delete the route.
Where
to?
To bypass a waypoint on a route:
1. Create a route as previously described.
2. Select the waypoint that follows the waypoint you are bypassing.
3. Select Navigate To > Go To (or Route To).
GPSMAP® 4000/5000 Series Owner’s Manual 23
Page 28
Viewing Information
Viewing Information
Use the Information screen to access information about tides, currents, celestial data, user data, other
boats, gauges, and video.
Viewing Tide Station Information
To view tide information from the Home screen, select Information > Tides. Information for the
most-recently viewed tide station is shown.
VieWinG
Select Nearby Stations to view other stations close to your current location. Select Change
information
Date > Manual to view tide information for a different date.
Viewing Current Information
Use the Current Prediction screen to view information for currents.
NOTE: You must use a BlueChart g2 Vision card to view Current Station information.
To view current information from the Home screen, select Information > Currents. Information
for the most-recently viewed current station is shown.
Select Nearby Stations to view other stations close to your current selection. Select Change
Date > Manual to view current information for a different date.
Select Show Report to view the Current Report for the selected station.
24 GPSMAP® 4000/5000 Series Owner’s Manual
Page 29
Viewing Information
Viewing Celestial Information
Use the Celestial screen to view celestial data for sunrise, sunset, moonrise, moonset, moon phase,
and approximate sky view location of the sun and moon.
To view celestial information from the Home screen, select Information > Celestial.
Moon position
Sun position
Sky view window
Viewing User Data
To view user data, from the Home screen, select Information > User Data.
i
nformation
VieWinG
Waypoints—view a list of all saved waypoints (page 22).
Routes—view a list of saved routes (page 22).
Tracks
—view a list of saved tracks.
Data Transfer
—transfer waypoints, routes, and tracks to and from an SD card or network.
Clear User Data—erase all user waypoints, routes, and tracks.
To copy or merge MapSource data to your chartplotter:
1. Insert the SD card into your chartplotter to allow it to place a le on the SD card. This le provides
information to MapSource to format its data. This only needs to be done the rst time you copy or
merge MapSource data to your chartplotter from a specic SD card.
2. Check your MapSource version on the PC by clicking Help > About MapSource. If the version
is older than 6.12.2, update to the most current version by clicking Help > Check for Software
Updates or check the Garmin Web site at www.garmin.com.
3. Insert the SD card into an SD card reader that is attached to the PC.
4. From within MapSource, click on Transfer > Send to Device.
5. From the Send to Device window, select the drive for the SD card reader and the types of data
you want to copy to your chartplotter.
6. Click Send.
7. Insert the SD card into your chartplotter.
8. From the Home screen on your chartplotter, select Information > User Data > Data Transfer >
Card.
9. Select Replace From Card or Merge From Card to copy or merge the data into your
chartplotter.
GPSMAP® 4000/5000 Series Owner’s Manual 25
Page 30
Viewing Information
To transfer data (waypoints, routes, tracks) to or from an SD card:
1. Insert an SD card into the SD card slot on the front of the unit.
2. From the Home screen, select Information > User Data > Data Transfer > Card.
Complete one of the following:
Select Save To Card to save waypoints, routes, and tracks to the SD card.
•
Select Merge From Card to transfer data from the SD card to the unit and combine it with
•
existing user data.
Select Replace From Card to overwrite items on your unit.
•
To transfer data to or from a network:
1. Connect the unit to a Garmin Marine Network using the network port on the back of the unit and
a Garmin Network cable.
2. From the Home screen, select Information > User Data > Data Transfer > Network.
Complete one of the following:
Select Clone User Data to transfer waypoints, routes, and tracks to other chartplotters
•
connected to the network. Existing data will be overwritten on those chartplotters.
Select Merge User Data to transfer data between all the chartplotters connected to the
•
network. Unique data will be combined with existing data on every chartplotter.
To back up data to a PC:
1. Insert an SD card into the SD card slot on the front of the unit.
2. From the Home screen, select Information > User Data > Data Transfer > Card > Save to
VieWinG
information
Card.
3. Remove the SD card from the chartplotter and insert it into an SD card reader that is attached to
a PC.
4. From Windows Explorer, open the Garmin\UserData folder on the SD card.
5. Copy the UserData.ADM le on the card and paste it to any location on the PC.
To restore backup data to your chartplotter:
1. Copy the UserData.ADM le from the PC to an SD card in a folder named Garmin\UserData.
2. Insert the SD card into your chartplotter.
3. From the Home screen on your chartplotter, select Information > User Data > Data Transfer >
Card > Replace From Card.
To delete all waypoints, routes, and tracks:
1. From the Home screen on your chartplotter, select Information > User Data > Clear User Data.
2. Select Waypoints, Routes, Saved Tracks, or All.
3. Select OK or Cancel.
Viewing Other Boats
To view information about other boats from the Home screen, select Information > Other Boats.
NOTE: To view information about other boats, your unit must be connected to an external AIS
(Automatic Identication System) or DSC (Digital Selective Calling) device.
AIS List—view information about the boats your unit is monitoring. Select AIS List to view the
MMSIs (Maritime Mobile Service Identities) or names (if the boat is broadcasting a name) of nearby
AIS-equipped boats. The AIS list is sorted by range, with the nearest boat at the top of the list.
26 GPSMAP® 4000/5000 Series Owner’s Manual
Page 31
Viewing Information
DSC Log—view a list of all DSC calls, sorted by most recent, sender, or by type (distress calls or
position reports).
View By Time
•
—view the most recent DSC calls received, sorted and displayed chronologically
by time and date. Calls with identical time and date information show the same information in the
list.
View By Sender—view an alphanumerical list of senders.
•
View By Type—view the most recent distress calls or position reports, sorted chronologically.
•
Delete All—delete all log entries.
•
DSC Call List—view the 100 most-recent calls. The DSC Call List shows the most-recent call from
a boat. If a second call is received from the same boat, it replaces the rst call in the Call List.
Directory—view a list of all DSC entries. You can view by name or by MMSI. You can also add an
entry.
Viewing Engine Gauges
To view analog or digital engine gauges from the Home screen, select Information > Gauges >
Engine.
i
nformation
VieWinG
NOTE: You must be connected to a NMEA 2000 network capable of sensing engine data to view the
gauges. See the GPSMAP 4000/5000 Series Installation Instructions for details.
To select analog or digital gauges:
1. While viewing the Gauges screen, press MENU.
2. Select Gauge Setup to select the number of engines (1–4), and the number of fuel tanks (1 or
2), and to reset the odometer to zero.
NOTE: For more than two engines, you can only use the digital gauges. For one or two engines, you
can switch between analog and digital gauges.
Viewing Fuel Gauges
To view fuel gauges from the Home screen, select Information > Gauges > Fuel. Fuel ow for
each engine, total fuel ow, fuel level in each tank, total fuel remaining, fuel economy, and the range
for your boat are shown.
NOTE: To view fuel information, your unit must be connected to an external fuel sensor, such as the
Garmin GFS 10.
GPSMAP® 4000/5000 Series Owner’s Manual 27
Page 32
Viewing Information
To synchronize your fuel gauges with your fuel:
From the Home screen select Information > Gauges > Fuel > Manage Fuel.
Fill Up—Select when your tank is full. An estimate of the total fuel is shown. Adjust if
•
necessary.
Add Fuel—Select when you have added less than a full tank. An estimate of the fuel added is
•
shown. Adjust if necessary.
Set Fuel Level—Select to specify the total fuel in your tanks.
•
Viewing Video
Your unit can display video if you connect it to a video source using the supplied video cable. See
the GPSMAP 4000/5000 Series Installation Instructions for details.
To view video from the Home screen, select Information > Video.
Select Menu to set up the following:
Source—selects the video device (1 or 2) to use to display video. If you have two video sources
•
and want to alternate between the two, select Alternate to dene the amount of time each video
is displayed.
Aspect—switches between the standard aspect ratio and a stretched aspect ratio. The video
•
cannot be stretched beyond the dimensions provided by the connected video device. Because of
this, the stretched video may not ll the entire screen of the GPSMAP 4012/5012.
VieWinG
Brightness—adjusts the brightness of the video feed up or down, or select Auto to allow the unit
•
information
to automatically adjust the brightness.
Saturation—adjusts the color saturation up or down, or select Auto to allow the unit to
•
automatically adjust the saturation.
Contrast—adjusts the contrast up or down, or select Auto to allow the unit to automatically
•
adjust the contrast.
Standard—selects the video format used by the source (PAL or NTSC). Select Auto to let the
•
unit automatically select the source format.
WARNING: Do not attempt to operate or watch video input while operating or navigating your boat.
Operating or watching the video input while the boat is moving could cause an accident or collision
resulting in property damage, serious injury, or death.
28 GPSMAP® 4000/5000 Series Owner’s Manual
Page 33
Conguring the Chartplotter
Conguring the Chartplotter
Use the Congure screen to congure unit settings.
Conguring System Settings
To change general system settings from the Home screen, select Congure > System.
Simulator—turn Simulator Mode On or Off. Select Setup to set simulator options. (If you set the
unit into a Store Demonstration mode during the initial unit setup, this setting is named Demo.)
Language—select the on-screen language.
Auto Power Up (GPSMAP 4010 and GPSMAP 5015 only)—turn Auto Power Up On or Off. When
On is selected, the chartplotter will automatically turn on whenever power is applied, unless the
chartplotter is turned off with the Power Key before power is lost.
Beeper/Display—select Beeper to set when the unit makes audible sounds. Select Backlight to
brighten or darken the backlight. Select Color Mode to switch between Day Mode and Night Mode.
GPS—view GPS satellites, turn WAAS/EGNOS on or off, select the source of GPS signals, and
set the speed lter to On, Off, or Auto. The speed lter averages the speed of your boat over a short
period of time for smoother speed values.
System Information—view system information, restore factory settings, view the status of
networked devices, and display the event log. The event log displays a list of system events. Select
the event to view additional information.
Overlay Numbers—view or edit the options for Wind (Apparent Wind or True Wind) and Next
Turn numbers (Distance or Time) for routes.
ConfiGUrinG the
Chartplotter
Changing Units of Measure
To change units of measure from the Home screen, select Congure > Units.
System Units—global setting that denes individual units of measure at the same time. Statute
(mh, ft, ºF), Metric (kh, m, ºC), Nautical (kt, ft, ºF), or Custom. Select Custom to individually
dene units of measure for depth, temperature, distance, speed, elevation, volume, and pressure.
NOTE: You must be receiving NMEA sonar depth data or using a Garmin sounder module to view
depth and water temperature information.
Heading—sets the reference used in calculating heading information.
Auto Mag Var—Automatic Magnetic Variation automatically sets the magnetic declination for
•
your location.
True—sets true north as the heading reference.
•
Grid—sets grid north as the heading reference (000º).
•
User Mag Var—allows you to set the magnetic variation value.
•
Position Format—change the coordinate style in which a given location reading appears. Do not
change the position format unless you are using a map or chart that species a different position
format.
Map Datum—change the coordinate system in which the map is structured. Do not change the Map
Datum unless you are using a map or chart that species a different Map Datum.
GPSMAP® 4000/5000 Series Owner’s Manual 29
Page 34
Conguring the Chartplotter
Time Format—select a 12-hour, 24-hour or UTC time format.
Time Zone
Daylight Saving Time
—set the time zone you want displayed for time readings.
—indicate whether you want daylight saving time Off, On, or Auto. The
auto setting automatically turns daylight saving time on or off, depending on the time of year.
Conguring Communications Settings
To change the communications settings from the Home screen, select Congure >
Communications.
Port Types—select the input/output format (NMEA Std. or NMEA High Speed) for each port
to use when connecting your chartplotter to external NMEA devices, a computer, or other Garmin
devices.
NMEA Std.—supports the input or output of standard NMEA 0183 data, DSC, and sonar NMEA
•
input support for the DPT, MTW, and VHW sentences.
NMEA High Speed—supports the input or output of standard 0183 data for most AIS receivers.
•
NMEA 0183 Setup—enable or disable NMEA 0183 output sentences for sounder, route, system,
and Garmin NMEA settings.
To enable or disable NMEA 0183 output sentences:
1. From the Home screen, select Congure > Communications > NMEA 0183 Setup.
2. Select a setting (Sounder, Route, System, or Garmin).
3. Select the NMEA 0183 output sentence.
4. Select Off to disable, or select On to enable the NMEA 0183 output sentence.
Posn. Precision—adjust the number of digits (Two Digits, Three Digits, or Four Digits) to
•
the right of the decimal point for transmission of NMEA output.
Waypoint IDs—select how the unit outputs waypoint identiers (Names or Numbers).
•
Chartplotter
ConfiGUrinG the
Defaults—reset NMEA 0183 settings to their default settings (OK or Cancel).
•
NMEA 2000 Setup—View and congure the devices connected to the NMEA 2000 network and set
bridging to On, Off, or Auto.
Device List—lists the NMEA 2000 devices on your network. If the NMEA 2000 device has
•
conguration options or settings, select the device for a list of options.
Bridging—enables or disables the output from Garmin sensors or NMEA 0183 devices to your
•
NMEA 2000 network.
Wireless Devices—Allows wireless devices, such as a remote control or optical mouse to
communicate with the chartplotter.
Preferred Sources—Allows selection of a preferred device when more than one source is available
for the same function.
Setting Alarms
You can set the unit to sound an audible alarm when certain conditions are met. By default, all
alarms are turned off.
To set an alarm:
1. From the Home screen, select Congure > Alarms.
2. Select an alarm category.
30 GPSMAP® 4000/5000 Series Owner’s Manual
Page 35
Conguring the Chartplotter
3. Select an alarm.
4. Select On to turn the alarm on, and then specify alarm information.
Setting Navigation Alarms
To set a navigation alarm, from the Home screen, select Congure > Alarms > Navigation.
Anchor Drag—set an alarm to sound when you exceed a specied drift distance.
Arrival—set an alarm to sound when you are within a specied distance or time from a destination
waypoint.
Off Course—set an alarm to sound when you are off course by a specied distance.
Setting System Alarms
To set a system alarm, from the Home screen, select Congure > Alarms > System.
Clock—set an alarm using the system (GPS) clock. The unit must be on for the clock alarm to work.
Battery—set an alarm to sound when the battery reaches a user-determined low voltage.
GPS Accuracy—set an alarm to sound when the GPS location accuracy falls outside the userdetermined value.
Setting Sonar Alarms
To set a sonar alarm, from the Home screen, select Congure > Alarms > Sonar.
NOTE: You must have an optional sonar module (and a transducer connected to the sounder module)
wired through NMEA 0183 or connected to the Garmin Marine Network to receive sonar information.
Shallow Water/Deep Water—set an alarm to sound when the depth is less than or greater than the
specied value.
Water Temp—set an alarm to sound when the transducer reports a temperature that is 2°F (1.1°C)
above or below the specied temperature.
Fish—set an alarm to sound when the unit detects a suspended target of the specied symbols.
— sounds an alarm for all sh sizes
— sounds an alarm for medium and large sh only
— sounds an alarm for large sh only
Conguring My Boat
To congure settings for your boat, from the Home screen, select Congure > My Boat.
Auto Guidance—set the Auto Guidance parameters for your boat:
Safe Depth—set the minimum depth (chart depth datum) to allow when calculating an auto
•
guidance path. A safe depth of less than one meter is not allowed when using Auto Guidance.
Safe Height—set the minimum height (chart height datum) of a bridge that your boat can safely
•
travel under.
Keel Offset—offset the surface reading for the depth of a keel, making it possible to measure depth
from the bottom of the keel instead of from the transducer location. Enter a positive number to offset
for a keel. Enter a negative number to offset for a large vessel that may draw several feet of water.
GPSMAP® 4000/5000 Series Owner’s Manual 31
ConfiGUrinG the
Chartplotter
Page 36
Conguring the Chartplotter
To adjust the Keel Offset:
1. From the Home screen, select Congure > My Boat > Keel Offset.
2. Use the ROCKER (GPSMAP 4000 series) or the screen keyboard (GPSMAP 5000 series) to
specify the offset.
3. Select Done to accept the number.
NOTE: Select Cancel to cancel your changes and return to the My Boat screen.
Transducer—select sonar-cone angles, and calibrate water speed.
Sonar Cone Angles—when using a transducer other than the standard Garmin transducer, you
•
can set the angle, in degrees, of the sonar cone so that it is accurately depicted on the Fish Eye 3D
screen. Select either 200kHz or 50kHz and use the on-screen keyboard to enter the angle.
NOTE: The Sonar Cone Angles setting is preset to match the cone angle of a standard Garmin dual-
frequency transducer. Use this option to match the specications of a non-standard transducer.
Calibrate Water Speed—use this menu to calibrate a speed-sensing device. Follow the on-
•
screen directions for calibration. If you do not have a speed-sensing device, this menu does not
appear.
NOTE: If the boat is not moving fast enough or the speed sensor is not registering a speed, a “Speed
Too Low” message appears. Select OK and safely increase boat speed. If you get the message again,
stop the boat and make sure the speed-sensor wheel is not stuck. If the wheel turns freely, check the
cable connections. If you continue to get the message, contact Garmin Product Support.
Conguring Other Boats
To congure settings for boats other than your own, from the Home screen, select Congure >
Other Boats.
AIS—turn AIS (Automatic Identication System) on or off. AIS alerts you to area trafc by
Chartplotter
ConfiGUrinG the
providing boat IDs, position, course, and speed for boats that are within range and equipped with a
transponder.
DSC—turn DSC (Digital Selective Calling) on or off.
NOTE: To congure AIS or DSC information for other boats, your unit must be connected to an
external AIS or DSC device.
Safe Zone—(AIS and MARPA only) turn a safe zone around your boat on or off. This is used for
collision avoidance, and can be customized.
To customize safe-zone settings:
From the Home screen, select Congure > Other Boats > Safe Zone > Setup.
Ring—show or hide a ring on the Navigation chart showing the safe zone for your boat.
•
Range—change the measured radius of the safe zone ring to a specied distance from 0.1 to
•
2.0 nm (or from 0.2 to 5.0 km, or from 0.1 to 2.0 mi).
Time to (Safe Zone)—sounds an alarm if AIS or MARPA determines that a target will intersect
•
the Safe Zone within the dened time interval (ranging from 3 to 24 minutes).
Details—show or hide the name, speed, and bearing of AIS or MARPA targets onscreen. The details
appear next to the AIS or MARPA target icon.
32 GPSMAP® 4000/5000 Series Owner’s Manual
Page 37
Using the Garmin Marine Network
Using the Garmin Marine Network
The Garmin Marine Network allows you to share data from Garmin peripheral devices between
Garmin chartplotters quickly and easily. You can connect your GPSMAP 4000 series and GPSMAP
5000 series chartplotters, and previous Garmin Marine Network compatible chartplotter models
(GPSMAP 3005/3006/3010), to your network to share data. With the Garmin Marine Network, you
can:
Share GPS data from a GPS 17 antenna that is wired to one chartplotter, with every chartplotter
•
connected to the Garmin Marine Network.
Share NMEA 0183 data from devices that are wired to one chartplotter, with every chartplotter
•
connected to the Garmin Marine Network.
NOTE: Both the GPS 17 and any NMEA 0183 devices must be connected to the same chartplotter to
achieve the best results when sharing data over the Garmin Marine Network.
NOTE: If you are using a GSD 21 wired to a GPSMAP 3006/3010 chartplotter, data is shared with
any GPSMAP 4000 series and GPSMAP 5000 series chartplotters connected to your Garmin Marine
network. All GSD 21 settings must be congured on the GPSMAP 3006/3010. You cannot wire a GSD
21 to a GPSMAP 4000 series or GPSMAP 5000 series chartplotter.
Share data from Garmin Marine Network devices connected to any chartplotter in the Marine
•
Network or to a GMS 10 Marine Network Port Expander, with every other chartplotter connected
to the Marine Network. These devices include:
GSD 22 digital sounder—provides sonar data when connected to the Garmin Marine
•
Network and an appropriate transducer. Sonar data is shared by all chartplotters on the
network.
GMR 21/41 Radome; GMR 18 Radome; and GMR 404/406 Open Array Radar—provide
•
radar data when connected to the Garmin Marine Network. Radar data is shared by all
chartplotters on the network.
Share BlueChart g2 Vision cartography data from an SD card inserted in one GPSMAP 4000
•
or GPSMAP 5000 series chartplotter with every GPSMAP 4000 and GPSMAP 5000 series
chartplotter connected to the Marine Network.
netWork
marine
NOTE: BlueChart g2 Vision cartography is only compatible with GPSMAP 4000 and GPSMAP 5000
series chartplotters. Previous Garmin Marine Network-compatible chartplotter models (such as the
GPSMAP 3010) can be connected to your network, but they cannot share BlueChart g2 Vision data.
Transfer waypoint, route, and track information from one chartplotter connected to the Garmin
•
Marine Network to every other chartplotter connected to the network. The data can be cloned
from one chartplotter to every other connected chartplotter, or the data can be merged and shared
with every connected GPSMAP 4000 and GPSMAP 5000 series chartplotter.
GPSMAP® 4000/5000 Series Owner’s Manual 33
Page 38
Using the Garmin Marine Network
Viewing Connected Garmin Marine Network Devices
To view all connected Garmin Marine Network devices, from the Home screen, select Congure >
System > System Information > Network Devices.
Aliases
dened
No alias
dened
Network Devices
Each connected device is listed along the right side of the screen. To assign an alias or name to one
of the devices for identication purposes, select the device. Use the ROCKER (GPSMAP 4000
series) or onscreen keyboard (GPSMAP 5000 series) to name the device.
Select Back or press the HOME key to exit.
marine
netWork
34 GPSMAP® 4000/5000 Series Owner’s Manual
Page 39
Using Radar
Using Radar
When you connect your chartplotter to an optional Garmin marine radar such as a GMR 404/406
or a GMR 18, you can view more information about your surroundings. The Garmin marine radar
connects through the Garmin Marine Network and shares radar data with all networked chartplotters.
The Garmin marine radar transmits a narrow beam of microwave energy as it rotates in a 360º
pattern. When the transmitted energy contacts a target, some of that energy is reected back to the
radar.
WARNING: The marine radar transmits microwave energy that has the potential to be harmful to
humans and animals. Before beginning radar transmission, verify that the area around the radar is clear.
The radar transmits a beam approximately 12° above and 12° below a line extending horizontally from
the center of the radar. Avoid looking directly at the radar, because the eyes are the most susceptible part
of the body.
To turn on the radar:
1. When you power the network on, the radar warms up. A countdown is provided to alert you when
the radar is ready. From the Home screen, press Radar > Cruising.
NOTE: As a safety feature, the radar enters standby mode after it warms up. This gives you an
opportunity to verify that the area around the radar is clear before beginning radar transmission. The
microwave energy transmitted by the radar can potentially be dangerous.
2. When the message “Ready to Transmit” appears, press or touch MENU.
3. On the lower-right portion of the screen, select Transmit Radar. A “Spinning Up” message
appears for a few moments, then the radar begins painting an image.
➊ ➋ ➌
To turn off the radar:
1. Press and release the Power key on the chartplotter (do not hold the button, or you may shut
down the chartplotter), or press MENU.
2. Select Go To Standby.
GPSMAP® 4000/5000 Series Owner’s Manual 35
radar
USinG
Page 40
Using Radar
Understanding the Cruising Screen
Use the Cruising screen to view a full-screen image of the gathered radar information. Your position
is in the center of the screen, and the rings provide distance measurements.
Range rings
Zoom scale
Heading line
Distance
between rings
The zoom scale represents the distance from your position (the center) to the outermost ring. Each
ring represents an even division of the zoom scale. For example, if the zoom scale is set at three
kilometers, each ring represents one kilometer from the center out. Use the RANGE (+/-) keys
(GPSMAP 4000 series) or the and keys (GPSMAP 5000 series) to adjust the zoom scale.
Cruising Screen Settings
To access additional settings or options for the radar cruising screen, press MENU.
Gain—
controls the sensitivity of the radar receiver. The default setting, Auto, adjusts automatically
to provide optimal performance. Select Up or Down to manually adjust the gain; select Auto to
return the gain to the default setting.
Rain Cltr—adjust the gain for unwanted clutter caused by rain at close ranges. Select Up or
•
Down to adjust the rain clutter sensitivity.
Sea Cltr—adjust the gain for clutter caused by choppy sea conditions. Select Nxt Prset to cycle
•
between Rough, Med, Calm, or Off. Select Up or Down to manually adjust the sea clutter
sensitivity.
Guard Zone—denes a safe zone around your boat. An alarm sounds when a detected object enters
this zone. Select On or Off. If the guard zone is on, you can dene the boundaries by selecting
Adjust Guard Zone.
Corner 1 (and Corner 2): Use the ROCKER (GPSMAP 4000 series) as indicated by the arrows
•
( and ) to dene the size of the guard zone. Select Corner 1 or Corner 2 to change the
reference point. For GPSMAP 5000 series units, touch Corner 1, and then touch the point on the
screen where you want the rst corner of the guard zone. Repeat this with Corner 2.
Circular: Joins the guard zone to completely encompass the boat. Use Corner 1 or Corner 2 to
•
USinG
radar
adjust the size.
Corner 1 Corner 2 Circular
Nav Features—hides or shows distance, arrival time, and bearing when navigating to a destination.
36 GPSMAP® 4000/5000 Series Owner’s Manual
Page 41
Using Radar
Overlay Numbers—show or hide cruising, navigation, shing, sailing, or fuel numbers.
Radar Setup—access advanced radar settings.
Orientation—change the perspective of the radar display.
•
Heading Line—show or hide a line in the direction of travel.
•
Rings—show or hide the radar range rings.
•
Look-Ahd Spd—turn on to shift your current location toward the bottom of the screen as your
•
speed increases. Enter your top speed for the best results.
•
Timed Xmit
Time
Xtalk Reject (Crosstalk)—lter out interference caused by another radar operating in close
•
—set and customize a transmit/standby cycle. Dene the transmission time (Xmit
) and standby time (Stdby Time) in minutes.
proximity.
Advanced—access advanced radar settings:
•
FTC (Fast Time Constant)—reduce unwanted clutter caused by rain at a distance.
•
Front of Boat—offset the front of the boat if you mount the radar at an angle.
•
Antenna Size (GMR 404/406 only)—select your antenna size (4 foot or 6 foot).
•
Motor Speed (GMR 404/406 only)—set the motor speed of your GMR 404/406 radar to
•
Normal Speed or High Speed. High Speed increases the speed at which the antenna rotates,
which increases the speed at which the screen updates.
Targeting on the Cruising Screen
Use the ROCKER (GPSMAP 4000 series) or touch the target location (GPSMAP 5000 series) to
begin targeting. A green ring and a green line appear. The green ring corresponds with the range
rings to help dene the distance of an object from your location. The green line corresponds with the
heading line to help dene the bearing of an object from your location. As you move the ROCKER,
you adjust the point where the green ring and green line intersect. This point indicates your target.
As you move the target over objects on the radar, target options appear along the right side of the
screen.
Heading line
Target
(intersection)
Target options
radar
Cruising Screen - Targeting
USinG
GPSMAP® 4000/5000 Series Owner’s Manual 37
Page 42
Using Radar
To stop targeting, select Stop Pointing.
Create Waypoint—marks a waypoint at the targeted object or location.
Acquire Target—assigns a MARPA (Mini Automatic Radar Plotting Aid) tag to the targeted object.
NOTE: MARPA requires the use of a heading sensor. The heading sensor must output the NMEA 0183
sentence HDM or HDG.
MARPA Target (only appears when you are targeting a tagged MARPA object)—opens the
MARPA target information window. Remove MARPA objects from this window.
MARPA target
lost
Tracking
MARPA object
Opens MARPA
target information
window
MARPA object
targeted
Dangerous
MARPA object
MARPA Targeting
Target options
Understanding the Radar Overlay Screen
Use the Radar Overlay option to overlay radar information on the Navigation chart.
Radar range
From the Home screen select Radar > Radar Overlay. The radar picture appears in orange and
overlays the Navigation chart. Use the RANGE (+/-) keys (GPSMAP 4000 series) or the and
keys (GPSMAP 5000 series) to zoom in and out. Zooming while panning the map only affects the
USinG
radar
zoom scale of the map. The radar range remains the same. Zooming while the map is locked on the
boat (not panning) affects the zoom scale of the map and the radar range.
To access additional settings or options for the radar overlay screen, touch or press MENU. Select
Adjust Chart > Chart Setup to access the chart options. Select Radar Setup to return to the radar
setup options.
38 GPSMAP® 4000/5000 Series Owner’s Manual
Page 43
Using Sonar
Using Sonar
When connected to an optional Garmin GSD 22 sounder module and a transducer, your chartplotter
can be used as a shnder. The GSD 22 connects through the Garmin Marine Network and shares
sonar data with every chartplotter connected to the network.
Understanding the Full Screen
Select the Full Screen option to view a full-screen graph of the sonar readings from the transducer.
The range scale along the right side of the screen shows the depth of detected objects as the screen
scrolls from the right to the left.
From the Home screen, select Sonar > Full Screen.
Depth, temperature,
and water speed
Suspended
target
Bottom
GPS speed and
GPS heading
Transducer
frequency
Range
Understanding the Split Zoom Screen
Use the Split Zoom screen to view the full sonar data from the graph and a zoomed-in portion on the
same screen.
From the Home screen, select Sonar > Split Zoom.
Depth, temperature,
and water speed
Zoomed depth
scale
GPS speed and
GPS heading
Zoom
window
Range
Zoom level
Transducer frequency
GPSMAP® 4000/5000 Series Owner’s Manual 39
Sonar
USinG
Page 44
Using Sonar
Understanding the Split Frequency Screen
Use the Split Frequency screen (dual-frequency transducer only) to view both the 50 kHz and 200
kHz frequencies on the same screen. A 200 kHz frequency graph appears on the left; a 50 kHz
frequency graph appears on the right.
From the Home screen, select Sonar > Split Frequency.
Depth, temperature,
and water speed
Range
GPS speed and
GPS heading
Transducer
frequencies
Understanding the Temp Log
If you are using a temperature-capable transducer, the Temp Log screen keeps a graphic log of
temperature readings over time. The current temperature and depth are shown in the upper-left
corner.
From the Home screen, select Sonar > Temp Log.
Temperature
and depth
Temperature
Range
Time
elapsed
The temperature appears along the right side and the time elapsed appears along the bottom. The
graph scrolls to the left as information is received.
USinG
Sonar
40 GPSMAP® 4000/5000 Series Owner’s Manual
Page 45
Using Sonar
Setting Up Sonar
Use the Sonar Setup screen to dene and adjust settings universal to all sonar screens.
From the Home screen, select Sonar > Sonar Setup.
Color Scheme—select white or blue. This affects the background on all sonar screens, but does not
change the Temp Log screen.
Fish Symbols—set how the sonar interprets suspended targets.
The unit does not interpret the sonar return data (default).
Suspended targets appear as symbols. Background sonar information appears, making the
distinction between sh and structure easier.
Suspended targets appear as symbols with background information shown. The target
depth of each symbol is also indicated.
Suspended targets appear as symbols. No background information appears.
Suspended targets appear as symbols with no background information shown. The target
depth of each symbol is indicated.
Scroll Speed—adjust the rate at which the sonar scrolls from right to left (Ultrascroll, Fast,
Medium, or Slow). If using a speed-capable transducer, select Auto to have the scroll speed
automatically adjust to the water speed of your boat.
Surface Noise—show or hide the sonar returns near the surface of the water. Hide surface noise to
help reduce clutter.
Whiteline—highlights the strongest signal from the bottom to help identify its hardness or softness.
Off—(default) Whiteline is disabled.
•
High—the most sensitive setting. Almost all strong returns are highlighted in white.
•
Medium—many strong returns are highlighted in white.
•
Low—the least sensitive setting. Only the strongest returns are highlighted in white.
•
Overlay Numbers—show or hide water temperature, water speed (if your transducer is capable),
and navigation numbers.
NOTE: To show water temperature or water speed, change the setting to Auto. If the connected
transducer is capable, the data is shown.
Sonar
USinG
GPSMAP® 4000/5000 Series Owner’s Manual 41
Page 46
Using Sonar
Advanced Sonar Settings
To adjust advanced sonar settings, press MENU while viewing a sonar screen.
Range—the range of the depth scale on the right side of the screen (Auto or, to adjust manually, Up
or Down).
Gain—controls the sensitivity of the sonar receiver (Auto or, to adjust manually, Up or Down). To
see more detail, increase the gain. If the screen is cluttered, decrease the gain.
Frequency—selects how the frequencies appear on screen (200kHz, 50kHz, or Dual).
Zoom—zoom in to a section of the Full Screen. The zoom is off, or set to No Zoom, by default.
Four options are available:
2x Zoom—twice the magnication. Select Up, Down, or Auto to set the depth range of the
•
magnied area.
4x Zoom—four times the magnication. Select Up, Down, or Auto to set the depth range of the
•
magnied area.
Bottom Lock—locks the zoom window to the bottom. Select Up, Down, or Auto to set the
•
depth range of the magnied area.
Depth Line—quickly reference a specic depth (On or Off). When On is selected, press up or
down on the ROCKER (GPSMAP 4000 series) or touch and drag the line (GPSMAP 5000 series) to
set the depth of the reference line.
A-Scope—creates a vertical asher along the right side of the screen (On or Off).
Sonar Setup—opens the Sonar Setup screen. See page 41.
USinG
Sonar
42 GPSMAP® 4000/5000 Series Owner’s Manual
Page 47
Appendix
Appendix
Specications
Physical Specications
Size: GPSMAP 4008: 7" H × 11.2" W × 4.2" D (176.9 × 284.4 × 106 mm)
GPSMAP 4010: 8.9" H × 13.4" W × 4.13" D (226.9 × 340.4 × 105.1 mm)
GPSMAP 4012: 9.5" H × 14.8" W × 4.13" D (240.5 × 375 × 105.1 mm)
GPSMAP 5008: 6.8" H × 10.1" W × 4.17" D (173.5 × 256 × 105.9 mm)
GPSMAP 5012: 9.47" H × 13" W × 4.7" D (240.5 × 330 × 119.2 mm)
GPSMAP 5015: 11.65" H × 15.55" W × 5.66" D (295.8 × 394.9 × 143.8 mm)
Weight: GPSMAP 4008: 6 lb. (2.7 kg)
GPSMAP 4010: 8 lb. (3.5 kg)
GPSMAP 4012: 10 lb. (4.5 kg)
GPSMAP 5008: 6 lb. (2.7 kg)
GPSMAP 5012: 9 lb. (4.3 kg)
GPSMAP 5015: 12 lb. (5.4 kg)
Display: GPSMAP 4008: 5.17" H × 6.85" W (131.4 × 174 mm)
GPSMAP 4010: 6.35" H × 8.43" W (161.4 × 214.2 mm)
GPSMAP 4012: 7.3" H × 9.7" W (184.3 × 245.8 mm)
GPSMAP 5008: 5" H × 6.73" W (128.2 × 170.9 mm)
GPSMAP 5012: 7.11" H × 9.3" W (180.49 × 235.97 mm)
GPSMAP 5015: 8.98" H × 11.97" W (228.1 × 304.1 mm)
Case: Fully Gasketed, high-impact plastic and aluminum alloy, waterproof to IEC 529-IPX
Temp. Range: from 5° to 131°F (from -15° to 55°C)
Compass Safe Distance: GPSMAP 4008/5008: 2.6 ft. (80 cm)
GPSMAP 4012/5012: 3.3 ft. (1 m)
GPSMAP 4010: 3.3 ft. (1 m)
GPSMAP 5015: 1.3 ft. (40 cm)
Hg
- LAMPS INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR
DISPOSED OF ACCORDING TO LOCAL, STATE, OR FEDERAL LAWS.
For more information go to:
www.garmin.com/aboutGarmin/environment/disposal.jsp.
GPS Performance (with GPS 17 antenna)
Receiver: Differential-ready 12 parallel channel WAAS-capable receiver
Acquisition Times:
Warm: 15 seconds
Cold: 45 seconds
AutoLocate: 2 minutes
Update Rate: 1/second, continuous
GPS Accuracy:
Position: <15 m (49 ft), 95% typical
Velocity: 0.05 meters/second steady state
GPSMAP® 4000/5000 Series Owner’s Manual 43
appendix
Page 48
Appendix
WAAS Accuracy:
Position: <3 m (9.8 ft), 95% typical
Velocity: 0.05 meters/second steady state
Dynamics: 6 g
Power
Source: 10–35 Vdc
Usage:
GPSMAP 4008/5008: 35 W max. at 10 Vdc
GPSMAP 4010/4012/5012: 40 W max at 10 Vdc
GPSMAP 5015: 60 W max at 10 Vdc
Fuse: 7.5 A, 42 V fast-acting
NMEA 2000 Specications:
Load Equivalency Number (LEN): 2
Unit Draw: 75 mA max
Initializing Unit Settings
The rst time you turn your unit on, you must congure a series of initial settings. These settings
must also be congured when restoring factory settings.
NOTE: You can change these settings later using the Congure screen.
Language—select the language to show on your screen.
Welcome—select OK.
Position Format—specify the coordinate system to use for location readings.
Time Format
—specify whether you want the time shown in a 12-hour, 24-hour, or UTC
(Universal Time Code) format.
Time Zone
—select your time zone.
Units—specify units for on screen measurements as Statute, Metric, or Nautical.
Minimum Safe Depth—select the minimum safe depth for your boat. Refer to your boat
specications for more information.
Minimum Overhead Clearance—select the minimum overhead clearance for your boat. Refer to
your boat specications for more information.
Calibrating the Touchscreen
For GPSMAP 5008/5012/5015 units, you might have to calibrate the touchscreen.
CAUTION: Do not calibrate the touchscreen unless you are certain that it is necessary.
To calibrate the touchscreen on GPSMAP 5000 series units:
1. Turn on the unit. When the Warning screen appears, touch and hold the black screen for at least
15 seconds until the calibration screen appears.
2. Follow the on-screen directions to calibrate the touchscreen.
appendix
44 GPSMAP® 4000/5000 Series Owner’s Manual
Page 49
Appendix
Alarms and Messages
Accuracy Alarm (GPS)—the GPS accuracy has fallen
outside the user-set value.
AIS: Dangerous Target—an AIS target presents a
collision threat.
Alarm Clock—the alarm clock has sounded.
Anchor Drag Alarm—the boat has drifted out of the user-
set distance range.
Antenna Input is Shorted —there is a short in the wiring
to the GPS 17 antenna.
Approaching Waypoint <name>—the boat is a specied
alarm distance from the destination waypoint.
Arrival Alarm <name>—arriving at destination waypoint.
Auto-guidance unable to calculate route—(BlueChart g2
Vision) auto-guidance cannot calculate the route.
Auto-guidance unable to calculate route, please shorten
route—(BlueChart g2 Vision) auto-guidance cannot
calculate the route, select a closer end point.
Auto-guidance unable to calculate route. Starting
position not within safe depth—(BlueChart g2 Vision)
auto-guidance cannot calculate the route; boat is not in a
safe depth.
Auto-guidance unable to calculate route. Ending
position not within safe depth—(BlueChart g2 Vision)
auto-guidance cannot calculate the route; select an end
point within the specied safe depth
Battery Alarm—Battery voltage is at or below the user-set
value.
Boat is not Moving Fast Enough to Calibrate—(speed
sensor) appears during water-speed calibration. Check
speed wheel for blockage and calibrate again. If wheel is
clear, calibrate again and increase speed.
Can’t Read User Card—cannot read card when
attempting a user data transfer.
Can’t Read Voltages That High, Limited To Top Of
Range—entering a battery-alarm voltage higher than the
unit can read.
Can’t Read Voltages That Low, Limited To Bottom Of
Range—entering a battery-alarm voltage lower than the
unit can read.
Can’t Unlock Maps—maps are locked and cannot be used
on this unit.
Can’t Write User Card— cannot write card when
attempting a user data transfer.
Cartography Service Incompatible. Software Update
Required—a software update is needed. Contact Garmin
Product Support for assistance updating your unit software.
Cooling Fan Voltage Too High
is higher than expected. Contact product support.
Cooling Fan Voltage Too Low
lower than expected. Contact product support.
Database Error—general database error. Contact Garmin
Product Support.
GPSMAP® 4000/5000 Series Owner’s Manual 45
—the cooling-fan voltage
—the cooling-fan voltage is
Deep Water Alarm—(sonar) the boat has entered user-
dened value for deep water.
Directory Item With This MMSI Already Exists
MMSI unit is already in directory.
Directory Memory is Full Can’t Create Entry—DSC
directory is full, no more entries can be created.
Distress Call Received From <name>—A distress call
has been received by the DSC module.
Drift Alarm—the boat has moved a user-dened distance.
DSC Position Report Received From <name>—a
position report has been received by the DSC module.
Entering Target Water Temperature—(temperature
sensor/transducer) the water temperature is inside the user-
dened target temperature zone.
GPS Antenna Has Lost Its Stored Settings—The GPS
antenna memory has been cleared. Contact Garmin Product
Support.
GPS Service Incompatible. Software Update
Required—a GPS service software update is needed.
Contact Garmin Product Support for assistance updating
your unit software.
GPS Service Lost—the unit has lost communications with
the remote GPS unit. Check the network and the antenna
wiring.
Incompatible Device, Software Update Required—an
incompatible device is attached that requires a software
update. Contact Garmin Product Support for assistance
updating your network.
Invalid Device Instance. Enter a number between
(0 - 252)—invalid NMEA 2000 Device instance.
Invalid Entry. Default value selected.—an invalid entry
was entered.
Invalid MMSI—an invalid DSC MMSI was entered.
Invalid System Instance. Enter a number between
(0 - 15)—invalid NMEA 2000 System instance.
Leaving Target Water Temperature—(temperature
sensor/transducer) the water temperature is outside the
user-dened target temperature zone
Low Fuel Alarm—(NMEA 2000) low fuel reported by the
NMEA 2000 network.
Lost Heading Sensor Connection— (radar/NMEA) the
unit has lost communications with the heading sensor.
Check wiring.
Lost Remote GPS Connection—connection to the remote
GPS has been lost. Check the network and the antenna
wiring.
Lost Satellite Reception—the unit has lost satellite
reception. Make sure you have a clear view of the sky.
Map Format Is Not Supported—a map format on a
preprogrammed SD card is not supported.
MARPA: Dangerous Target—(radar) a MARPA target
has become dangerous.
—the
appendix
Page 50
Appendix
MARPA: Target Lost—(radar) unable to track a MARPA
target any longer.
NMEA Depth Is Below Transducer—(sonar) the NMEA
depth input is using the DBT sentence which does not
include keel offset.
No DGPS Position—the unit lost differential GPS
reception (WAAS). Make sure you have a clear view of
the sky.
No Proximity Waypoints Found—no proximity
waypoints found while attempting a user data transfer.
No Routes Found—no routes found while attempting a
user data transfer.
No Tracks Found—no tracks found while attempting a
user data transfer.
No User Waypoints Found—no user waypoints found
while attempting a user data transfer.
Not All Maps Fit, Some Maps Will Not Be Drawn—
there are more maps present on the SD card than the unit
can support. Some maps on the card will not be drawn or
used to nd map features.
Off Course Alarm—the boat has left the user-dened
course.
Proximity Alarm—the boat has come close to a user-
dened proximity point.
Proximity Alarm Memory is Full—the proximity
waypoint memory is full. Erase existing proximity
waypoints to make room.
Proximity Overlaps Another Proximity Waypoint—a
proximity point is overlapping another proximity waypoint.
Radar Guard Zone Alarm—(radar) an object has been
detected in the user-dened radar guard zone.
Radar Needs Repair Error Code—(radar) the radar needs
repair. An error code will be listed to help diagnose the
error.
Radar Service Incompatible. Software Update
Required—a radar software update is needed. Contact
Garmin Product Support for assistance updating your
network.
Radar Service Lost—(radar) the unit has lost
communications with the remote radar unit. Check the
network and the radar wiring.
Route Already Exists—the named route already exists.
Select another name.
Route is Full—the individual route is full, no more
waypoints can be added.
Route Memory is Full, Can’t Create Route—the
chartplotter route memory is full, no more routes can be
created. Erase existing routes to make room.
Route Truncated—some points on the end of the route
have been discarded.
Shallow Water Alarm—(sonar) the boat has entered the
user-dened shallow-water depth.
Simulating Operation—the unit is in Simulator Mode.
appendix
46 GPSMAP® 4000/5000 Series Owner’s Manual
Sonar Failed, Unit Needs Repair—there has been a sonar
failure and the unit needs to be sent in for repair. Contact
Garmin Product Support.
Sonar Service Incompatible. Software Update
Required—a software update is needed. Contact Garmin
Product Support for assistance updating your network.
Sonar Service Lost—(sonar) the unit has lost
communications with the remote sonar unit. Check the
network and the sonar wiring.
Tide Alarm
alarm range.
Track Already Exists
Select another name.
Track Log Full—there is no longer any space in the active
track log storage.
Track Truncated—some points on the end of the track
have been discarded.
Transducer Disconnected, Sonar Turned Off—the
transducer has been disconnected. Sonar has been turned
off. Check transducer wiring.
Transfer Complete—user data transfer is complete.
Unknown bridge height within calculated auto-guidance
route—(BlueChart g2 Vision) there is an unknown bridge
height within the auto-guidance route.
User Card Not Found—user data card transfer. Make sure
an SD card is fully inserted.
Water Speed Sensor not Working—the water speed
sensor is not working properly. Check the wheel for
obstructions and check wiring.
Water Temperature Alarm—(temperature sensor/
transducer) the water temperature has entered or left the
user-dened water temperature alarm zone.
Warning: Auto-guidance route starting position moved
due to safe depth settings—(BlueChart g2 Vision) auto-
guidance has calculated the route, but the starting point has
been moved to deeper water.
Warning: Auto-guidance route ending position moved
due to safe depth settings (BlueChart g2 Vision) auto-
guidance has calculated the route, but the end point has
been moved to deeper water.
Waypoint Already Exists—the named waypoint already
exists. Select another name.
Waypoint Memory is Full, Can’t Create Waypoint—the
User Waypoint memory is full. Erase existing waypoints to
make room.
—the tide has reached the user-specied tide
—the named track already exists.
Page 51
Appendix
Product Registration
Help us better support you by completing our online registration today! Connect to our Web site at
http://my.garmin.com. Keep the original sales receipt, or a photocopy, in a safe place.
Contact Garmin
Contact Garmin if you have any questions while using your GPSMAP 4000 series or GPSMAP 5000
series chartplotter. In the USA contact Garmin Product Support by phone: (913) 397-8200 or (800)
800-1020, or go to www.garmin.com/support.
In Europe, contact Garmin (Europe) Ltd. at +44 (0) 870.8501241 (outside the UK) or 0808 2380000
(within the UK).
Declaration of Conformity (DoC)
Hereby, Garmin, declares that this unit is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
To view the full Declaration of Conformity, see the Garmin Web site for your Garmin product:
www.garmin.com/products/gpsmap4008
•
www.garmin.com/products/gpsmap4010
•
www.garmin.com/products/gpsmap4012
•
www.garmin.com/products/gpsmap5008
•
www.garmin.com/products/gpsmap5012
•
www.garmin.com/products/gpsmap5015
•
Click Manuals, and then select the Declaration of Conformity link.
Software License Agreement
BY USING THE UNIT, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING
SOFTWARE LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT CAREFULLY.
Garmin grants you a limited license to use the software embedded in this device (the “Software”) in binary executable
form in the normal operation of the product. Title, ownership rights, and intellectual property rights in and to the Software
remain in Garmin.
You acknowledge that the Software is the property of Garmin and is protected under the United States of America
copyright laws and international copyright treaties. You further acknowledge that the structure, organization, and code of
the Software are valuable trade secrets of Garmin and that the Software in source code form remains a valuable trade secret
of Garmin. You agree not to decompile, disassemble, modify, reverse assemble, reverse engineer, or reduce to human
readable form the Software or any part thereof or create any derivative works based on the Software. You agree not to
export or re-export the Software to any country in violation of the export control laws of the United States of America.
appendix
GPSMAP® 4000/5000 Series Owner’s Manual 47
Page 52
Appendix
NMEA 0183 and NMEA 2000
The GPSMAP 4000 and GPSMAP 5000 series chartplotters can accept data from NMEA 0183
compliant devices and also from certain NMEA 2000 devices connected to an existing NMEA 2000
network on your boat.
NMEA 0183
The NMEA 0183 data cable included with the GPSMAP 4000 and GPSMAP 5000 series
chartplotters support the NMEA 0183 standard, which is used to wire various NMEA 0183compliant devices such as VHF radios, NMEA instruments, autopilots, wind sensors, or heading
sensors.
The GPSMAP 4000 and GPSMAP 5000 series chartplotters can receive data from up to four NMEA
0183-compliant devices and send GPS data to up to six NMEA 0183-compliant devices.
To wire a GPSMAP 4000 or GPSMAP 5000 series chartplotter to optional NMEA 0183-compliant
devices, see the GPSMAP 4000/5000 Series Installation Instructions.
Approved NMEA 0183 sentences:
GPBWC, GPRMC, GPGGA, GPGSA, GPGSV, GPGLL, GPBOD, GPRMB, GPRTE, GPVTG,
GPWPL, GPXTE, and Garmin proprietary sentences—PGRME, PGRMM, and PGRMZ.
This unit also includes support for the WPL sentence, DSC, and sonar NMEA 0183 input with
support for the DPT (depth) or DBT, MTW (water temp), and VHW (water temp, speed, and
heading) sentences.
NOTE: To congure how the unit manages these NMEA 0183 sentences, see page 30.
NMEA 2000
The GPSMAP 4000 and GPSMAP 5000 series chartplotters are NMEA 2000 certied and can
receive data from a NMEA 2000 network installed on the boat.
To connect a GPSMAP 4000 or GPSMAP 5000 series chartplotter to an existing NMEA 2000
network and to see a list of supported NMEA 2000 PGN numbers, see the GPSMAP 4000/5000
Series Installation Instructions.
All GPSMAP 4000 and GPSMAP 5000 series chartplotters are NMEA 2000
certied.
appendix
48 GPSMAP® 4000/5000 Series Owner’s Manual
Page 53
Index
Index
A
A-scope 42
additional object information 7
aerial photos 15
AIS 26, 32
alarms 30, 45
navigation 31
safe zone 32
sonar 31
system 31
anchor drag 31
antenna size (radar) 37
automatic guidance 15, 31
B
backing up data 26
backlight
adjusting 2
sensor 1
backlight sensor 1
beeper 29
BlueChart g2 Vision 11, 33
bottom lock 42
bridging 30
C
calibrate water speed 32
celestial information 25
chart appearance 9
chart data 5
charts 4, 5
additional object information 7
appearance 9
borders 9
detail 9
sh eye 3D 5
shing 5
mariner’s eye 5
navigation 5
panning 6
settings 9
using 5
zooming 5
clear user data 26
colors 12
color mode 3
color scheme 41
combinations 16–17
communications settings 30
congure 4, 29–32
my boat 31
other boats 32
water speed 32
contact Garmin 47
course up 9
create waypoint 7
creating routes 22
cruising screen (radar) 36
current information 24
current station 15, 24
D
data
clear user data 26
transfer 26, 33
user 25
declaration of conformity 47
delete all 26
delete a waypoint 22, 26
depth line 42
detail 9
device list 30
DSC 26, 32
E
edit a route 23
edit existing waypoint 21
EGNOS 29
engine gauges 27
F
factory settings
restoring 3
sh eye 3D 5, 13
settings 13
shing charts 13
sh symbols 41
frequency 42
FTC 37
fuel gauges 27
full screen 39
G
gain 42
gauges
engine 27
fuel 27
GMR 18 33, 35
GMR 21/41 33
GMR 404/406 33, 35, 37
go to 18
GPS satellite signals 3, 29
GSD 22 33
guard zone 36
guide to 18
H
heading 29
heading line 9
cruising screen 37
high-resolution satellite imagery 14
home screen i, 4
I
information 4, 7
AIS 26
DSC 26
information screen 24
other boats 26
initializing the unit 43
K
keel offset 31
L
lane width 8
language 29
light sectors 9
look-ahd spd 37
M
man overboard 21
map datum 29
MapSource data 25
marine network 33
mariner’s eye 5, 8
settings 8
mariner’s eye 3D 12
colors 12
mark current location 21
mark key 1
MARPA 38
menu key 1
messages 45
motor speed (radar) 37
move a waypoint 21
my boat 31
N
navigate to 7, 18
navigation chart 5
nearby stations 24
network 33–34
viewing connected devices 34
NMEA 0183 30, 48
NMEA 2000 30, 44, 48
north up 9
numbers 5, 8, 13
numeric keypad 1
O
object information 7
orientation 9, 37
other boats 26, 32
overlay numbers 5, 8, 13, 29, 37, 41
GPSMAP® 4000/5000 Series Owner’s Manual 49
Page 54
Index
P
panning the navigation chart 6
photos 9, 14, 15
POI data 15
position format 29
position icon 6
POWER key 1
preferred devices 30
product registration 47
R
radar 35–38
antenna size 37
motor speed 37
overlay screen 38
setup 37
range 42
Range keys 1
registration 47
restoring factory settings 3
review 7
rings 8, 37
roads 15
Rocker 1
routes
creating 22
deleting all 26
editing 23
route to 18
sonar 39–42
a-scope 42
color scheme 41
depth line 42
sh symbols 41
frequency 42
full screen 39
gain 42
range 42
scroll speed 41
split frequency screen 40
split zoom screen 39
surface noise 41
temp log 40
whiteline 41
zoom 42
sonar cone 13
sonar cone angles 32
specications 43
split frequency screen 40
split zoom screen 39
spot depths 9
stop navigating 19
sun and moon 25
surface noise 41
symbols 9
system information
viewing
3
system settings 29
waypoint 20
create new 20
delete 22
edit existing 21
man overboard 21
mark current location 21
moving 21
waypoints
deleting 21
where to 4, 18–23
whiteline 41
wireless devices 30
X
xtalk reject 37
Z
zoom 5, 42
S
safe depth 8, 12, 31
safe height 31
safe zone 32
satellite signals 3
scroll speed 41
SD cards
inserting and removing 3
search for a destination by name 19
settings
alarms 30
chart 9
combinations 17
communications 30
sh eye 3D 13
initializing 44
mariner’s eye 8
mariner’s eye 3D 12
navigation chart 5
radar 37
sonar 41
sonar (advanced) 42
system 29
show radar 8
simulator mode 4, 29
soft keys i, 1
T
targeting (radar) 37
temp log 40
tide station 7, 24
timed xmit 37
tracks 8, 9, 10, 13
deleting all 26
track up 9
transfer data 26, 33
turn the unit off 2
U
unit ID number
viewing
3
units of measure 29
user data 25
V
video 28
view
system information
W
WAAS 29
3
50 GPSMAP® 4000/5000 Series Owner’s Manual
Page 55
Page 56
For the latest free software updates (excluding map data) throughout the life of your
Garmin products, visit the Garmin Web site at www.garmin.com.
© 2008 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street, Olathe, Kansas 66062, USA
Garmin (Europe) Ltd.
Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9RB UK
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com
Part Number 190-00854-00 Rev. D
Loading...