Contents:
CUTALONG BOLD LINE
CUTALONG BOLD LINE
TRIM ALONG DASHED LINE
3/8"
DRILLA HOLE FOR
APLACE TO BEGIN CUTTING
INSIDEEDGE OF POCKET
Flush Mount Installation Instructions
Flush Mount Pocket:
Mounts to the bulkhead
and retains the unit
Mounting Hardware:
A - Foam Rubber Pads (2)
B - M4x40mm Hew Head Screws (4)
C - M4 Hex Nuts (4)
D - Reusable Cable Tie (1)
E - Metal Retaining Brackets (2)
Tool List (Not Included)
Jig Saw Phillips Screwdriver
7mm Wrench Drill and 3/8’ Drill Bit
Masking Tape Thread Locking Compound — (Optional)
Safety Goggles and Dust Mask for drilling
Please read through these instructions thoroughly before attempting installation. Make
sure you completely understand these instructions before you begin. When in doubt, seek
professional assistance. Be sure the cables will reach the unit and transducer location before
beginning installation. Please check the packing list above. If you are missing any items,
please contact your Garmin dealer. Be sure to wear safety goggles and dusk mask when drilling and cutting.
Installing the Flush Mount Pocket
1. Using the supplied Mounting Template locate a suitable mounting location and
tape the template in place. Be sure to check behind the installation area to
avoid cutting or drilling into wiring, cables, etc.
2. Drill a 3/8” hole at the location in di cat ed on the template as a starting point,
then using the Jig Saw, cut the panel along the bold line. Be sure that your
initial cut does not go outside the line that in di cates the inside edge of the
pocket. (Figure 1)
3. Using a file or sandpaper, remove any burrs from the open ing. Test fit the Flush
Mount Pocket and make any ad just ments to correct the fit.
4. Install the two Foam Rubber Pads in the pocket at the locations indicated in
Figure 2. To install the pads, peel the lining off of the back and install with the
sticky side against the pocket.
5. Insert the pocket in the panel (The Garmin logo should be positioned at the
top.) Install a M4 Hex Head Screw through the pocket and the corresponding
hole in the Metal Retaining Bracket. Start a 4mm Hex Nut on the screw. Repeat
the process until all 4 nuts are started (Figure 3). Tighten the M4 nuts using a
7mm wrench or socket.
If operating in a high vibration environment it is recommended
that you use a thread locking compound on the M4 Hex Head Screws.
6. Secure the cable to the rectangular slot on the left side of the Flush Mount
Pocket or one of the metal retaining brack ets with the wire tie provided in the
kit. Leave approximately 18” of cable extending through the pocket to aid in
the installation and removal of the unit.
A
E
B
C
D
Figure 1
Rubber Pad Location
Figure 2
Boat Panel
Metal Retaining Bracket
Mounting Pocket
M45x40mm Hex Head
Wire Tie Slot
M4 Machine Nut
Side View
Figure 3
Installing/Removing the Unit
1. Connect the wiring harness to the unit, making sure the locking ring is
fully tightened. (Figure 4)
2. Slide the Fishfinder into the pocket. When the Fishfinder is fully inserted,
it will click into place at the lock tabs (Figure 5). It may be necessary to
apply some pressure when inserting the assembly into the pocket to
compress the foam rubber pads.
3. To remove the unit from the pocket, press the lock tabs toward the unit
while sliding the unit out of the pocket. (Figure 6)
Figure 4
Lock Tabs
Figure 5
© 2003 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151
Unit 5, The Quadrangle, Abbey Park In dus tri al Estate, Romsey, SO51 9DL, U.K.
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
st
Street, Olathe, Kansas 66062, U.S.A
Garmin (Europe) Ltd.
Garmin Corporation
www.garmin.com
Part Number 190-00311-00 Rev. A
Figure 6