Edge® 1000
Quick Start Manual
April 2014 190-01694-01_0C Printed in Taiwan
Introduction
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Always consult your physician before you begin or modify any
exercise program.
Getting Started
When using your device the first time, you should complete
these tasks to set up the device and learn about the basic
features.
Charge the device (Charging the Device).
1
Install your device using the standard mount (Installing the
2
Standard Mount) or the out-front mount (Installing the OutFront Mount).
Turn on the device (Turning On the Device).
3
Locate satellites (Acquiring Satellite Signals).
4
Go for a ride (Going for a Ride).
5
Upload your ride to Garmin Connect™ (Sending Your Ride to
6
Garmin Connect).
Register the device (Registering Your Device).
7
Get the owner's manual (Getting the Owner's Manual).
8
Charging the Device
Place the bike mount on the bike stem.
3
Attach the bike mount securely using the two bands Á.
4
Align the tabs on the back of the device with the bike mount
5
notches Â.
Press down slightly and turn the device clockwise until it
6
locks into place.
NOTICE
To prevent corrosion, thoroughly dry the USB port, the weather
cap, and the surrounding area before charging or connecting to
a computer.
The device is powered by a built-in lithium-ion battery that you
can charge using a standard wall outlet or a USB port on your
computer.
NOTE: The device will not charge when outside the
temperature range of 32° to 104°F (0° to 40°C).
Pull up the weather cap À from the USB port Á.
1
Plug the small end of the USB cable into the USB port on the
2
device.
Plug the large end of the USB cable into an AC adapter or a
3
computer USB port.
Plug the AC adapter into a standard wall outlet.
4
When you connect the device to a power source, the device
turns on.
Charge the device completely.
5
Installing the Standard Mount
For the best GPS reception, position the bike mount so the front
of the device is oriented toward the sky. You can install the bike
mount on the stem or the handlebars.
Select a secure location to mount the device where it does
1
not interfere with the safe operation of your bike.
Place the rubber disk À on the back of the bike mount.
2
The rubber tabs align with the back of the bike mount so it
stays in place.
Installing the Out-Front Mount
Select a secure location to mount the Edge device where it
1
does not interfere with the safe operation of your bike.
Use the hex key to remove the screw À from the handlebar
2
connector Á.
If necessary, remove the two screws on the back side of the
3
mount Â, rotate the connector Ã, and replace the screws to
change the orientation of the mount.
Place the rubber pad around the handlebar:
4
• If the handlebar diameter is 25.4 mm, use the thicker pad.
• If the handlebar diameter is 31.8 mm, use the thinner pad.
Place the handlebar connector around the rubber pad.
5
Replace and tighten the screw.
6
NOTE: Garmin® recommends a torque specification of 7 lbf-
in. (0.8 N-m). You should check the tightness of the screw
periodically.
Align the tabs on the back of the Edge device with the bike
7
mount notches Ä.
2
Press down slightly and turn the Edge device clockwise until
8
it locks into place.
Releasing the Edge
Turn the Edge clockwise to unlock the device.
1
Lift the Edge off the mount.
2
Turning On the Device
The first time you turn on the device, you are prompted to
configure system settings and profiles.
Hold .
1
Follow the on-screen instructions.
2
If your device includes ANT+™ sensors (such as a heart rate
monitor, speed sensor, or cadence sensor), you can activate
them during configuration.
For more information about ANT+ sensors, see ANT+ Sensors.
Keys
The timer overlay allows you to return to the home screen
during a ride.
• Select to save your changes and close the page.
• Select to close the page and return to the previous page.
• Select to return to the previous page.
• Select to return to the home screen.
• Select and to scroll.
• Select to search near a location.
• Select to search by name.
• Select to delete an item.
Viewing the Connections Page
The connections page displays the status of the GPS, ANT+
sensors, wireless connection, and your smartphone.
From the home screen, select the status bar or swipe down
from the top of the page.
À
Á
Â
Home Screen Overview
The home screen gives you quick access to all the features of
the Edge device.
RIDE Select to go for a ride.
Train Select to change your activity profile.
Where To? Select to search for and navigate to a location.
Calendar Select to view scheduled activities and completed rides.
History Select to manage your history and personal records.
Courses Select to manage your courses.
Segments Select to manage your segments.
Workouts Select to manage your workouts.
Select to enter sleep mode and wake the device.
Hold to turn the device on and off.
Select to mark a new lap.
Select to start and stop the timer.
Select to view the settings menu.
The connections page appears. A flashing icon means the
device is searching. You can select any icon to change the
settings.
Acquiring Satellite Signals
The device may need a clear view of the sky to acquire satellite
signals. The time and date are set automatically based on the
GPS position.
Go outdoors to an open area.
1
The front of the device should be oriented toward the sky.
Wait while the device locates satellites.
2
It may take 30–60 seconds to locate satellite signals.
Going for a Ride
Before you can record speed and distance, you must locate
satellite signals or pair your device with an optional ANT+ speed
sensor.
NOTE: History is recorded only while the timer is running.
From the home screen, select RIDE.
1
Wait while the device locates satellites.
2
Select to start the timer.
3
Using the Touchscreen
• When the timer is running, tap the screen to view the timer
overlay.
3