P3PC-6112-01EN
fi-760PRB Imprinter
Operator’s Guide
Contents
Introduction.............................................................................................................................. 2
Chapter 1 Preparations.......................................................................................................... 4
1.1 Checking the Package Contents...............................................................................................4
1.2 Names of Component Parts......................................................................................................4
Chapter 2 Installation............................................................................................................. 6
2.1 Installing the Imprinter...............................................................................................................6
2.2 Loading the Print Cartridge .......................................................................................................8
2.3 Test Print.................................................................................................................................10
Chapter 3 Basic Operation .................................................................................................. 12
3.1 Setting the Print Position.........................................................................................................12
3.2 Using the Paper Guides..........................................................................................................12
3.3 Print Setup ..............................................................................................................................14
3.4 Replacing the Print Cartridge..................................................................................................14
3.5 Removing Jammed Documents..............................................................................................16
Chapter 4 Daily Care ........................................................................................................... 18
4.1 Cleaning the Print Cartridge....................................................................................................18
4.2 Cleaning the Imprinter.............................................................................................................18
4.3 Cleaning the Rollers................................................................................................................19
4.4 Cleaning Materials ..................................................................................................................19
Chapter 5 Error Messages................................................................................................... 20
Chapter 6 Specifications...................................................................................................... 21
Contact for Inquiries .............................................................................................................. 23
1
Introduction
Thank you for your purchase of the fi-760PRB Imprinter.
The fi-760PRB Imprinter is an optional unit to be used
with the fi-7600 image scanner.
This manual explains installation and connection, basic
operations, and regular maintenance of the fi-760PRB
Imprinter. Use the product correctly according to this
manual.
For how to use the fi-7600 image scanner, refer to
"fi-7600/fi-7700/fi-7700S Image Scanner Operator's
Guide" contained in the setup DVD-ROM included in the
package.
We hope that this manual helps you make the most of
the imprinter.
June 2017
Safety Information
The "Safety Precautions" manual that is supplied with
the scanner contains important information about the
safety and the correct way of using this product. Make
sure that you read and understand it before using this
product.
Manufacturer
PFU Limited
YOKOHAMA i-MARK PLACE, 4-4-5 Minatomirai,
Nishi-ku, Yokohama, Kanagawa, 220-8567, Japan
© PFU Limited 2017
Trademarks
Microsoft, Windows, and Windows Server are either
registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
PaperStream is a registered trademark of PFU Limited
in Japan.
Other company names and product names are the
registered trademarks or trademarks of the respective
companies.
Abbreviations Used in This Manual
The operating systems and products in this manual are
indicated as follows.
Name Indication
Windows Server
®
2008 Standard
(32-bit/64-bit)
®
Windows Server
2008 R2 Standard
(64-bit)
Windows
®
7 Home Premium
(32-bit/64-bit)
®
Windows
7 Professional (32-bit/64-
bit)
®
Windows
Windows
Windows Server
7 Enterprise (32-bit/64-bit)
®
7 Ultimate (32-bit/64-bit)
®
2012 Standard
(64-bit)
®
Windows Server
2012 R2 Standard
(64-bit)
®
Windows
Windows
Windows
Windows
Windows
Windows
Windows
Windows Server
8.1 (32-bit/64-bit)
®
8.1 Pro (32-bit/64-bit)
®
8.1 Enterprise (32-bit/64-bit)
®
10 Home (32-bit/64-bit)
®
10 Pro (32-bit/64-bit)
®
10 Enterprise (32-bit/64-bit)
®
10 Education (32-bit/64-bit)
®
2016 Standard
(64-bit)
PaperStream IP (TWAIN)
PaperStream IP (TWAIN ×64)
PaperStream IP (ISIS) Bundle
fi-760PRB Imprinter imprinter
Windows
Server 2008
(*1)
Windows 7
(*1)
Windows
Server 2012
(*1)
Windows
Server 2012
R2 (*1)
Windows 8.1
(*1)
Windows 10
(*1)
Windows
Server 2016
(*1)
PaperStream
IP driver
fi-7600 image scanner scanner
fi-7600/fi-7700/fi-7700S Image
Scanner Operator's Guide
Operator's
Guide
*1: Where there is no distinction between the differe
versio
ns of the above operating system, the general
term "Windows" is used.
2
nt
Arrow Symbols in This Manual
Right-arrow symbols () are used to separate icons or
menu options you should select in succession.
Click [Start] menu [Control Panel].
Screen Examples in This Manual
Microsoft product screenshots are reprinted with
permission from Microsoft Corporation.
The screen examples in this manual are subject to
change without notice in the interest of product
development.
If the actual displayed screen differs from the screen
examples in this manual, operate by following the actual
displayed screen while referring to the user's manual of
the scanner application that you are using.
The screen examples used in this manual are of the
PaperStream IP driver.
The screenshots used in this manual are of Windows 7.
The actual windows and operations may differ
depending on the operating system. Also note that with
some scanner models, the screens and operations may
differ from this manual when you update the
PaperStream IP driver. In that case, refer to the manual
provided upon updating the driver.
3
Chapter 1 Preparations
Print Cartridge
Cover
Print Section
Lock
EXT Cable
Lock
Operator Panel
The scanner has an operator panel on each side.
LCD
[Menu] Button
[
] Button/[] Button
[Stop/Clear] Button
[Scan/Enter] Button
[Power] Button
ADF (Automatic
Document Feeder)
Stacker
ADF Paper Chute
(Feeder)
When the operator panel
is fitted into the side of
the scanner
1.1 Checking the Package Contents
Check the package contents list that is included in the
imprinter package box to make sure that all items are
included in the package.
If anything is missing or damaged, contact your
FUJITSU scanner dealer or an authorized FUJITSU
scanner service provider.
Use this product and accessories carefully.
1.2 Names of Component Parts
■ Imprinter Unit
Front
■ Imprinter with Scanner
Front
Back
■ Attachment Guide
Back
4
■ Inside
Print Cartridge Holder
Print Cartridge Cover
Paper Guide
5
Chapter 2 Installation
1
2
1
2
Attachment Guide
ADF
Bar
ADF
Bar
Attachment Guide
2.1 Installing the Imprinter
Install the imprinter as follows:
ATTENTION
Do not move the scanner with the imprinter
installed. The imprinter may be damaged.
1 Turn off the scanner power and disconnect the
power cable.
2 Remove the stacker from the scanner.
1 Check that the stacker is placed in the lower position.
You can lower the position of the stacker by tilting it
upwards a little.
2 Hold the center ( ) of the stacker and slightly
bend it to remove the right side ( ) of the stacker
from the slot in the direction of the arrow.
2 Look into the scanner from below to check the
position of the bar.
3 Align the attachment guide with the bar.
ATTENTION
You must remove the stacker before inst
imprinter
Do not pull forcibly, since this might damage
st
acker.
.
3 Attach the attachment guide to the scanner.
1 Make sure that the direction of the attachment guide
is the same as direction shown in the following figure.
4 Lift the attachment guide from underneath to attach
it.
alling the
the
6
ATTENTION
After
Installation
Confirm the following after attaching the attachment guide.
The attachment guide is not tilted.
The attachment guide is fitted in the scanner, and not
overhanging.
Good: The attachment guide is properly attached.
Bad: The attachment guide is tilted.
Bad: The attachment guide is overhanging.
HINT
Removing the Attachment Guide
To remove the attachment guide, press your fingers
against the attachment guide and slide it
downward.
ATTENTION
Be careful not to get your fingers caught.
5 Raise the locks (two locks on the back side).
4 Attach the scanner onto the imprinter.
Hold the scanner above the rear of the imprinter
and gently lower it onto the base of the imprinter
until it fits in place.
7
6 Turn the locks inside (two locks on the back side).
1
2
1
2
LQNLHW
SULQWFRQUJKH
KSFT
KS
7 Connect the EXT cable to the connector on the
back of the scanner.
2.2 Loading the Print Cartridge
Load the print cartridge as follows:
ATTENTION
When installing the print cartridge, install
operly.
pr
When you do not use the imprinter for a long time
re
move the print cartridge from the imprinter. Ink
will be consumed every time the scanner is
powered-on even if printing is not done.
1 Turn off the scanner.
2 Place your hand in the middle part of the print
ca
rtridge and open it as shown below.
it
,
ATTENTION
The imprinter will not work if the EXT cable is not
connected to the scanner. Scanning when the EXT
cable is not connected can cause documents to
jam inside the imprinter.
8 Install the stacker removed from the scanner (in
procedure 2) to the imprinter.
Insert the protrusion on the right side of the stacker
into the slot and then push the left side of the
stacker along the slot in the direction of the
arrow.
3 Remove the tape that holds the print cartridge
holder and the paper guides.
4 Lift the print cartridge holder by pinching the lever
with your fingers as shown below.
5 Take out the print cartridge from the bag.
9 Connect the power cable to the scanner.
8
6 Remove the protection tape on the print cartridge.
%/$&.
&$
Print Circuit
Film
%/$&.
&$
Catches
%/$&.
&$
ATTENTION
Do not touch the metal part of the print cartridge nor put the
tape back again.
7 With the tab on the print cartridge facing right, put
the print cartridge into the holder.
9 Move the print cartridge to an appropriate printing
position.
The print cartridge should be positioned within the
section where the document will pass through.
10 Close the print cartridge cover.
ATTENTION
Be careful not to let the print cartridge catch the
print circuit film to avoid damaging the film.
8 Bring down the arm of the print cartridge holder
down gently until it locks in and set the print
cartridge in place.
Make sure that the catches (both sides) on the arm
latch onto the print cartridge firmly.
9
2.3 Test Print
%/$&.
&$
Test Pattern Print Sample
Feed Direction
1
2
3
4
5
6
5 mm
After loading the print cartridge, check if the printing
operation works normally.
HINT
For details about the operator panel, refer to the
Operator's Guide provided with the scanner.
1 Push the [Power] button of the operator panel of the
scanner.
The [Ready] screen is shown on the LCD.
2 Load a blank document in the scanner.
5 Select [1: Single Sheet Only] or [2: Multiple Sheets]
by pressing the [
then confirm the selection by pressing the [Scan/
Enter] button.
When [2: Multiple Sheets] is selected, printing is
performed for all sheets set in the scanner.
The [Print Pattern] screen is shown on the LCD.
] button or the [] button, and
6 Select a print pattern by pressing the [] button or
the [
] button, and then confirm the selection by
pressing the [Scan/Enter] button.
HINT
Below are the print test patterns:
HINT
Use A3 or Double Letter size blank paper. If the
paper size is smaller, printing may not be
completed successfully.
Confirm that the print cartridge is positioned within
the document width.
3 Press the [Menu] button.
Menu
Stop/Clear
Check
Test Pattern 1 (Horizontal):
ABCDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_`0000
0000
Test Pattern 2 (Horizontal):
abcdefghijklmnopqrstuvwxyz{|}¯ 00000000
Test Pattern 3 (Horizontal):
!"#$%&'()*+,-./0123456789:;<=>?@00000000
Test Pattern 4 (Vertical):
ABCDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_`0000
0000
Test Pattern 5 (Vertical):
abcdefghijklmnopqrstuvwxyz{|}¯ 00000000
Test Pattern 6 (Vertical):
!"#$%&'()*+,-./0123456789:;<=>?@00000000
The numbering section "00000000" increases in
increments of one, starting from 0 (zero).
Scan/Enter
Power
The [Settings Menu] screen is shown on the
LCD.
4 Select [3: Test Print] by pressing the [] button or
the [
] button, and confirm the selection by
pressing the [Scan/Enter] button.
The [No. of Sheets Scanned] screen is shown
on the LCD.
ATTENTION
If the Imprinter is disconnected or not connected
properly, [Cannot use this function because the
Imprinter is not connected.] is shown on the LCD.
The [Test Print] screen is shown on the LCD.
10
7 Select [1: Yes] by pressing the [] button or the
[
] button, and then confirm the selection by
pressing the [Scan/Enter] button.
The blank sheet is fed into the scanner, and the
imprinter will print out a print test pattern leaving
a 5 mm gap (with an allowance of 4 mm inwards
or outwards) from the edge of the document.
8 To finish the print test, press the [Power] button on
the operator panel of the scanner to turn off the
power of the scanner.
ATTENTION
Do not move the imprinter or give it a jolt while
printing. Printing may be out of order.
11
Chapter 3 Basic Operation
%/$&.
&$
%/$&.
&$
Document Feed
Direction
%/$&.
&$
Paper Guides
Print Circuit
Film
3.1 Setting the Print Position
Set the print position in the following steps:
1 Open the print cartridge cover.
2 Move the print cartridge to an appropriate printing
position.
Hold the print cartridge as below, and slide it to the
left or right within the document width to set it at a
suitable print starting position.
HINT
The triangle-shaped protrusion on the print
cartridge holder indicates the print head. Use the
protrusion as a guide for the print position.
You can find the document size markings on the
imprinter above the print cartridge. Use the
markings as a guide for the document width.
Load the actual document in the scanner a
make sure that the print cartridge is positioned
within the width of document.
nd
3.2 Using the Paper Guides
When documents have curled edges like below, use the
paper guides to prevent paper jams.
Move the paper guides to the positions where the edges
of documents pass through in the following steps:
1 Load documents in the scanner.
2 Open the print cartridge cover.
3 Slide the paper guides and align them with the
edges of the document.
3 Close the print cartridge cover.
12
ATTENTION
Be careful not to let the paper guides come into
contact with the print circuit film to avoid damaging
the film.
&$
%/$&.
HINT
1
2
%/$&.
&$
1
2
%/$&.
&$
1
2
Paper Guide
Paper Guide
Metal Wheel
Paper Guide
When you want to perform a print on the left or right
margin of a wide document, the paper guide may
get in the way. In this case, remove the paper guide
and attach it to a place near the center where
space is available ( ). After that, move the print
cartridge to the left or right margin ( ).
When the print position is on the right margin
When the print position is on the left margin
■ Removing the Paper Guides
2 Push the head of the paper guide until it fits in well.
To remove the paper guides, pinch the paper guide with
your fingers and pull it out as shown below.
■ Attaching the Paper Guides
1 Place the paper guide as shown in the figure below.
Make sure that the paper guide is under the metal
wheel.
13
3.3 Print Setup
%/$&.
&$
%/$&.
&$
3.4 Replacing the Print Cartridge
You can configure settings for the imprinter by using the
scanner driver's setup window.
■ PaperStream IP (TWAIN) (Example)
Display the Normal dialog and configure the settings in
[Imprinter] of [Endorser].
The print cartridge is a consumable.
Replace the print cartridge as follows:
ATTENTION
When the following message appears, replace th
int cartridge as soon as possible. If you continue
pr
to print without replacing the cartridge, your print
output will be faded.
When replacing the print cartridge, make sure
alled properly.
inst
1 Turn off the scanner.
2 Place your hand in the middle part of the print
ca
rtridge and open it as shown below.
e
it is
HINT
The following items can be specified. For details,
refer to the help of the PaperStream IP driver.
Imprinter status (on or off)
Whether or not the setup dialog box is displayed
Whether the PaperStream IP driver
synchr
onized with the Digital Endorser
Printing settings (such as font type, direct
pr
int starting position, character strings to be
is
ion, the
printed, and initial, increased and decreased
values for the counter)
3 Lift the print cartridge holder by pinching the lever
with your fingers as shown below.
14
4 Remove the old print cartridge.
Print Circuit
Film
Catches
%/$&.
&$
5 Remove the protection tape on the new print
cartridge.
ATTENTION
Do not touch the metal part of the print cartridge nor
put the tape back again.
7 Bring down the arm of the print cartridge holder
down gently until it locks in and set the print
cartridge in place.
Make sure that the catches (both sides) on the arm
latch onto the print cartridge firmly.
&$
%/$&.
8 Move the print cartridge to an appropriate printing
position.
The print cartridge should be positioned within the
section where the document will pass through.
6 With the tab on the print cartridge facing right, put
the print cartridge into the holder.
ATTENTION
Be careful not to let the print cartridge catch the
print circuit film to avoid damaging the film.
&$
%/$&.
ATTENTION
Depending on the position of the print cartridge,
printing may not fit within the document when
printing close to the document edge.
9 Close the print cartridge cover.
10 Turn on the scanner.
15
11 Reset the ink counter in the following procedure.
ADF
Print
Section
3.5 Removing Jammed Documents
ATTENTION
Be sure to reset the ink counter after replacing the
print cartridge.
1 Display the [Software Operation Panel] window.
Windows Server 2008/Windows 7
Click [Start] menu [All Programs] [fi Series]
[Software Operation Panel].
Windows Server 2012
Right-click the Start screen, and select [All apps] on
the app bar [Software Operation Panel] under [fi
Series].
Windows Server 2012 R2/Windows 8.1
Click [] on the lower left side of the Start screen and
select [Software Operation Panel] under [fi Series].
To display [], move the mouse cursor.
Windows 10/Windows Server 2016
Click [Start] menu [fi Series] [Software
Operation Panel].
2 Click [Device Setting] from the list on the left, and
then click the [Clear] button of [Remaining Ink].
If a document jams, remove the jammed document as
follows:
ATTENTION
Open the ADF and the print section to remove the
jammed document. Do not pull out the document
forcefully.
1 Remove the documents from the ADF paper chute
(fee
der).
2 Hold the middle part of the print section, and open it
as
shown in the figure.
The value of the counter is set to 100.
3 Click the [OK] button on the [Software Operation
Panel] window.
4 A message appears. Click the [OK] button.
The [Software Operation Panel] window closes,
and the ink counter is cleared.
ATTENTION
When you open the ADF, be sure to open the print
section beforehand.
3 Open the ADF.
4 Remove the jammed document.
16
5 Close the ADF.
ADF
Print
Section
6 Hold the middle part of the print section, and close it
as shown in the figure.
ATTENTION
Make sure that the ADF is closed before you close
the print section.
Be careful not to get your fingers caught.
17
Chapter 4 Daily Care
Nozzle Plate
Contact Part
4.1 Cleaning the Print Cartridge
Ink stains stuck to the nozzle plate of the print cartridge
or leaving the imprinter unused for a while may cause
poor print quality due to a clogged nozzle. If your
imprinter has these types of trouble, clean the nozzle
plate of the print cartridge.
ATTENTION
For cleaning, use a dry lint-free cloth, and gently
wipe off the excess ink from the surface of the
nozzle plate. (Do not use a tissue.)
HINT
If the nozzle is still clogged after cleaning the print
cartridge, replace it with a new cartridge.
1 Turn off the scanner.
2 Remove the print cartridge.
(Refer to "3.4 Replacing the Print Cartridge" (page
14).)
4.2 Cleaning the Imprinter
While you use the imprinter frequently, ink sticks to the
print cartridge holder base which makes the paper dirty.
As a part of daily maintenance, clean the print cartridge
holder base by following the procedure below.
ATTENTION
When cleaning, use an absorbent cloth or a waste
cloth, and gently wipe off the ink.
If the ink is dried, gently wipe it with a moistened
cloth. (Since the ink is water soluble, it can be
cleaned with water.)
1 Turn off the scanner.
2 Remove the print cartridge.
(Refer to "3.4 Replacing the Print Cartridge" (page
14).)
3 Open the print section.
4 Clean the print cartridge holder base by pressing a
cloth or a waste cloth gently on it to wipe off the ink.
ATTENTION
Be careful not to touch the nozzle plate or the
contact part with your hand as this may cause poor
print quality or contact errors.
3 Wipe off the excess ink on the nozzle plate gently.
4 Make sure that the excess ink is removed and then
reinstall the print cartridge.
(Refer to "3.4 Replacing the Print Cartridge" (page
14).)
ATTENTION
When installing the print cartridge, install it
properly.
ATTENTION
When cleaning, be careful not to touch the metal
wheels located at the print section.
5 Confirm that the ink is removed and then close the
print section.
6 Reinstall the print cartridge.
(Refer to "3.4 Replacing the Print Cartridge" (page
14).)
18
4.3 Cleaning the Rollers
Print Section
Rubber Rollers
Print Section
Plastic Rollers
When ink or paper dust is stuck on the imprinter feed
roller surfaces, documents may not feed smoothly.
To prevent feed problems, clean the roller surfaces
regularly.
ATTENTION
It may take a long time to dry if an excessive
amount of Cleaner F1 is used. Use it in small
quantity. Wipe off the cleaner completely to leave
no residue on the cleaned parts.
HINT
The recommended cleaning cycle is every 5,000
sheets. The actual cleaning cycle may be shorter
depending on how often the imprinter is used and
the documents.
1 Open the print section.
2 Clean the rubber rollers.
Clean the rubber rollers (eight in total) under the
feeding section.
3 Clean the plastic rollers.
Clean the two plastic rollers (black) at the print
section.
Rotate the rollers manually while gently wiping the
dirt and dust off the surface of the rollers with a
cloth moistened with Cleaner F1.
4 Confirm that the dirt is removed and then close the
print section.
4.4 Cleaning Materials
Name Part No. Notes
Gently wipe the dirt and dust off the surface of the
rollers with a cloth moistened with Cleaner F1.
Clean the entire surface of the rubber rollers as you
rotate them manually.
ATTENTION
When cleaning, be careful not to touch the metal
wheels located at the print section.
Cleaner F1 PA03950-
0352
Cleaning Wipe PA03950-
0419
*1: Pre-moistened with Cleaner F1. It can be used
instead of moistening a cloth with Cleaner F1.
ATTENTION
In order to use the cleaning materials correctly and
safely, read the precautions on each product
thoroughly.
For information about the cleaning materials, contact
your FUJITSU scanner dealer or an authorized
FUJITSU scanner service provider.
Volume: 100 ml
24 packets
(*1)
19
Chapter 5 Error Messages
This chapter explains the imprinter error messages.
Error codes and error messages are displayed on the LCD. Refer to the error codes and the error messages that are
displayed for troubleshooting.
HINT
For details on the error messages and other errors, refer to the Operator's Guide provided with the scanner.
Error Code Error Details Action
J1:5A
U5:4A (*1)
U6:B4
U7:B9
A1:B3
A3:B6
A4:B8
A2:B5
H6:B1
Paper jam (Imprinter) Try the following:
1. Remove the jammed document from the imprinter.
2. Make sure that the document is an appropriate one for scanning
with the imprinter.
3. Clean the rollers.
Imprinter Cover Open Close the print section of the imprinter, and load the document again.
Print cartridge not installed No print cartridge is installed.
Check if the print cartridge is installed correctly.
Imprinting area error Adjust the imprinting start position and the imprinter strings to fit the
imprinting area in the document.
Imprinter error (communication timeout) An error occurred in the imprinter.
Try the following:
Imprinter error (EEPROM)
Imprinter error (ROM)
Imprinter error (print head) An error occurred in the imprinter.
Imprinter system error An error occurred in the imprinter.
1. Confirm that the EXT cable of the imprinter is connected properly
to the EXT connector on the back of the scanner.
2. Check if the print cartridge is installed correctly.
3. Turn the scanner off then back on.
If the problem persists, write down the displayed error code and
contact your FUJITSU scanner dealer or an authorized FUJITSU
scanner service provider.
Try the following:
1. Confirm that the EXT cable of the imprinter is connected properly
to the EXT connector on the back of the scanner.
2. Check if the print cartridge is installed correctly.
3. If you have a new print cartridge, replace the old print cartridge with
the new one.
4. Turn the scanner off then back on.
If the problem persists, write down the displayed error code and
contact your FUJITSU scanner dealer or an authorized FUJITSU
scanner service provider.
Turn the scanner off then back on.
If the problem persists, write down the displayed error code and
contact your FUJITSU scanner dealer or an authorized FUJITSU
scanner service provider.
*1: When you open the imprinter print section while the scanner is in standby, only an error message will appear withou
an error code. Also, note that buttons on the operator panel are disabled while the imprinter print section is open.
20
t
Chapter 6 Specifications
ATTENTION
Documents with glossy surface such as thermal paper, thermal transfer paper, coated
paper, and art paper take longer time for the ink to dry and may cause poor print quality.
The imprinter must be cleaned more frequently if you use these types of papers.
Thick plastic documents such as credit cards and a Carrier Sheet cannot be scanned
when the imprinter is installed.
D
C
A
B
Printing
Area
(Back)
Feed Direction
ATTENTION
Do not print within 5 mm from the edge of the
document.
Item Specification
Printing Method
Print Timing
Printing Characters
Maximum Number
of Characters per
Line
Print Orientation
Character Size
Character Pitch
Font Style
Character Width
Document That Can
Be Scanned
Thermal inkjet printing
Post printing, back surface printing
Alphabet: A to Z, a to z
Numeric characters: 0, 1 to 9
Symbols: ! " # $ % & ' ( ) * + , - . / : ; < = > ? @ [ ¥ ] ^ _ ` { | } ¯
Maximum of 43 digits
Normal, Bold: 0°, 180° (horizontal), 90°, 270° (vertical)
Narrow: 0°, 180° (horizontal)
Normal, Bold: Height 2.91 × width 2.82 mm/0.1146 × 0.1110 in. (horizontal orientation),
Height 2.82 × width 2.91 mm/0.1110 × 0.1146 in. (vertical orientation)
Narrow: Height 2.91 × width 2.12 mm/0.1146 × 0.0835 in. (horizontal orientation)
3.53 mm/0.1390 in. (Normal, Bold), 2.54 mm/0.10 in. (Narrow)
Regular, Bold
Normal, Bold, Narrow
Documents that can be scanned with the scanner
For details, refer to the Operator's Guide provided with the scanner.
Note that paper weight should be 52 to 128 g/m
2
(14 to 34 lb).
Printing Area
A = 5 mm
B = 5 mm
C = 5 mm
D = 5 mm
(0.20 in.)
Accuracy of Printing
±4 mm/0.16 in. from the starting point for feed direction
Position
Dimension
Weight
Without scanner: 360 (W) × 435 (D) × 228 (H) (mm)/14.17 (W) × 17.13
(D) × 8.98 (H) (in.)
With scanner: 360 (W) × 435 (D) × 264 (H) (mm)/14.17 (W) × 17.13 (D)
× 10.39 (H) (in.)
4.2 kg (9.26 lb)
21
(Excluding the interface cable,
ADF paper chute (feeder) and
stacker)
Item Specification
Ambient Condition
Consumable
Temperature: 10 to 35°C (50 to 95 °F), Humidity: 20 to 80%
Print cartridge (PART No.: CA00050-0262) (See "Contact for Purchasing Consumables or Cleaning
Materials" (page 23).)
The printable number of characters: 4,000,000 characters (The printable number of characters differs
depending on the characters to be printed.)
Replacement cycle: 4,000,000 characters or six months after opening (A print cartridge has a specific
expiration date, and the expiration period differs whether the package is opened or
not. Start using the print cartridge before the expiration date that is written on the
package.)
22
Contact for Inquiries
Refer to the contact list on the last page of the
Safety Precautions manual.
Image Scanner fi Series
For other inquiries regarding the scanner, refer to
the following web page:
http://imagescanner.fujitsu.com/g-support.html
If the solution to your problem cannot be found on
the above web page, refer to the contact
information for your Fujitsu office on the following
web page:
http://imagescanner.fujitsu.com/warranty.html
Contact for Purchasing Consumables or
Cleaning Materials
http://www.fujitsu.com/global/shop/computing/
IMAGE_index.html
23
fi-760PRB Imprinter
Operator's Guide
P3PC-6112-01EN
Issue date: June 2017
Issued by: PFU Limited
The contents of this manual are subject to change without notice.
PFU Limited assumes no liability for incidental or consequential damages ar
fro
m the use of this product, and any claims by a third party.
Copying of the contents of this manual, in whole or in part, as well as the
ap
plications is prohibited under the copyright law.
scanner
ising
Loading...