How it Works
Fujitsu
Loading...
FI-6670A
User Manual
212 pgs13.36 Mb0
User Manual
29 pgs1.59 Mb0
Table of contents
Loading...

Fujitsu FI-6670A User Manual

fi-6670(A)/fi-6770(A)/fi-6750S
P3PC-2252-02ENZ0
TOP
Contents
Index
Operator’s Guide
Thank you for purchasing a fi-6670(A) / fi-6770(A) / fi-6750S Color Image Scanner series. This manual provides the basics of how to operate and handle the scanner. Refer to the Getting Started for information on how to install and connect the scanner, and how to install related scanning software.
Shows scanner’s parts names and their functions plus the basic operation.
Explains how to load documents on the scanner.
Explains how to scan documents using a scanning application “ScandAll PRO.”
Describes the configurable parameters in the scanner drivers.
Explains how to scan various types of doc­uments.
Explains how to clean the scanner.
Explains how to replace the scanner con­sumables.
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Explains how to troubleshoot scanner problems.
Explains how to configure scanner settings using the Software Operation Panel.
How to Use This Manual
Trouble­shooting
Operational Settings
Appendix
Glossary

How to Use This Manual

TOP
Contents
How to Use This Manual
The following shows the tips for using this manual.
Cover page
P3PC-2252-01Z0
(A)
(
)
fi-6670
A
Operator’s Guide
Thank you for purchasing the fi-6670(A) / fi-6770(A) / fi-6750S Color Image Scanner series. This manual provides the basics of Refer to the Getting Started for information how to intall related
/fi-6770
scanning software,
/fi-6750S
how to operate and handle the scanner.
on how to install and
connect the scanner, and
rts names and their
Shows scanner’s pa functions plus the basic operation.
Explains how to load documents on the scanner.
Explains how to scan document using a scanning application “ScandAll PRO.”
Describes the parameters configurable in the scanner drivers.
Explains how to scan various types of doc­uments.
Explains how to clean the scanner.
Explains how to replace the consumables of the scanner.
Explains how to troubleshoot.
Explains how to configure scanner settings using the Software Operation Panel.
How to Use
TOP: Moves to the top page of this manual. Contents: Moves to the top page of the Table of Contents. Index: Moves to the top page of the Index section.
TOP
Contents
Index
Introduction
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Scans
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
Contents page
...........34
.............49
TOP
Contents
Index
Introduction
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Scans
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
14
Contents
Contents
How to Use This Manual ........................................2
Introduction .............................................................3
Regulatory Information ........................................... 4
Conventions ............................................................6
Precautions .............................................................8
Safety Information ................................................10
Chapter 1Scanner Overview .............................. 18
1.1 Overview and Features ..................................... 19
Overview.............................................................. 19
Features............................................................... 19
1.2 Scanner Parts and Their Functions .................20
fi-6670(A) (ADF Type).......................................... 20
fi-6770(A)/fi-6750S (FB Type).............................. 22
Model-Common Parts.......................................... 25
1.3 Functions of the Operator Panel ......................26
Operator Panel..................................................... 26
Indications on the Function Number Display........28
1.4 Turning the Scanner On and Off ......................29
Turning the Scanner On....................................... 29
Turning the Scanner Off.......................................29
1.5 Power Save Mode ..............................................30
Returning from e Power Save
1.6 Scanning Documents ........................................31
Chapter 2Loading Documents ..........................33
Mode.................... 30
2.1 Loading Documents on the ADF ...........
2.2 ADF-Loaded Documents .................................. 37
Sizes.....................................................................37
Paper Quality........................................................37
Maximum Document Loading Capacity................39
Area Not to be Perforated.................................... 39
Loading Documents with Tabs or
Non-Rectangular Documents............................... 40
Multifeed Detection Conditions.............................40
Limiting the Background Color Area.....................41
Job Separation Sheet...........................................42
2.3 Changing the ADF Position (FB Type Only) ... 43
2.4 Loading Documents on the Flatbed
(FB Type Only) ...................................................44
Chapter 3How to Use ScandAll PRO ................45
3.1 Overview of ScandAll PRO ...............................46
3.2 Launching ScandAll
3.3 Selecting a Scanner Driver ...............................48
3.4 Selecting a Scanner Model .
3.5 Scan Parameters ............................................... 50
3.6 Selecting a Scanning Method
PRO .................................47
.................
(with [Scan Settings]) ........................................51
Scan..................................................................... 51
Batch Scan........................................................... 51
Clicking the title moves to the page that describes it.
Clicking a desired chapter title moves to its top page.
Moves to this page (here).
Index page
Index
Index
A
ADF-Loaded Documents................................................ 42
Advanced Scanning........................................................ 79
B
Basic Flow of Scanning Documents............................... 33
Basic Specification........................................................ 189
Before Contacting Your Dealer or Scanner Service Provider
151
C
Changing the ADF Position............................................ 48
Checking Labels on the Scanner................................... 153
Cleaning Materials and Locations Requiring Cleaning.. 114
Cleaning the ADF.......................................................... 116
Cleaning the Flatbed (Flatbed Type Only)..................... 121
Configurable Items........................................................ 156
Consumables................................................................. 122
Consumables and the Replacement Cycles.................. 123
Conventions...................................................................... 7
Customizing the Hardware Settings.............................. 105
D
Daily Care...................................................................... 113
E
Errors Indicated on the Operator Panel......................... 131
Clicking the page for the desired item in the Index moves to the page that describes it.
Common Notes:
• Clicking a blue-colored character string (where your mouse pointer
changes to the shape of a hand pointing upward (such as ) when you hover over the string) moves to the linked section.
• In this manual, you can use the navigation option of Adobe
or Adobe For details, refer to the Adobe
• Keyboard assistance is also available. Use the PageUp key to go to
the previous page, and the PageDown key to the next page.
F
Features.......................................................................... 21
FUJITSU ISIS Scanner Driver......................................... 67
FUJITSU TWAIN 32 Scanner Driver............................... 64
Functions of the Operator Panels.................................... 28
H
How to Use ScandAll PRO.............................................. 51
How to Use This Manual.................................................. 2
I
Installation Specification................................................ 191
Introduction....................................................................... 3
L
Launching ScandAll PRO................................................ 53
Loading Documents........................................................ 38
Loading Documents on the ADF..................................... 39
Loading Documents on the Flatbed (Flatbed Type Only) 50
O
Options.......................................................................... 194
Outer Dimensions.......................................................... 192
Overview of ScandAll PRO............................................. 52
P
Paper Jams................................................................... 129
Power ON/OFF Control................................................. 187
Power Save Mode........................................................... 32
®
Reader.
TOP
Contents
Index
Introduction
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appndix
Glossary
209
®
Acrobat®
®
Acrobat® or Adobe® Reader Help.
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
2

Introduction

TOP
Contents
Introduction
Thank you for purchasing our fi-6670(A)/fi-6770(A)/fi-6750S series Color Image Scanner.
Scanner Models
This manual covers the following five scanner models, each featur­ing as:
Model Description
fi-6670 fi-6670A
fi-6770 fi-6770A
fi-6750S Equipped with an automatic document feeder (ADF) for
Equipped with an automatic document feeder (ADF) for automatic document feeding and duplex scanning. The fi-6670A comes with a color graphics adapter (CGA) board as a standard feature. It enables advanced image processing at a high speed when used with Kofax VRS.
Equipped with an automatic document feeder (ADF) for automatic document feeding and duplex scanning, and a flatbed for scanning documents such as thin paper or thick books. The fi-6770A comes with a color graphics adapter (CGA) board as a standard feature. It enables advanced image processing at a high speed when used with Kofax VRS.
automatic document feeding and simplex scanning, and a flatbed for scanning documents such as thin paper or thick books. The ADF features simplex scanning only.
Manuals
The following manuals are included in the for the scanner. Read them as needed.
Manual Description
Package Contents List (paper)
Getting Started (paper, PDF)
Operator’s Guide (This Manual)) (PDF)
FUJITSU TWAIN 32 User’s Guide (PDF)
Image Processing Software Option User’s Guide (PDF)
Lists all the items contained in the scanner package. Make sure all are included in the package.
Outlines the procedures from installing up to starting the operation of the scanner. Read this manual first.
Provides detailed information on how to operate, and maintain the scanner daily, how to replace the consumables, and how to troubleshoot problems. Included in the SETUP DVD-ROM.The PDF data is included in the SETUP DVD-ROM.
Explains how to install and operate the FUJITSU TWAIN 32 scanner driver. Included in the SETUP DVD-ROM.
Explains how to install and operate the Image Processing Software Option. Included in the SETUP DVD-ROM.
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
VRS Note (PDF) Explains how to connect and install Kofax
VRS. Included in the SETUP DVD-ROM.
Operational Settings
Appendix
Glossary
3
Introduction
Manual Description
Error Recovery Guide (HTML help)
Help - Embedded in scanner drivers
Help - Embedded in related applications
Details the status of the scanner and explains how to resolve problems encountered. Contains movies that explain how to replace the consumables. Included in the SETUP DVD-ROM.
Explains how to use the scanner drivers, and how to configure the settings for them.
Explains how to use and configure the settings for the application software. Use help files as necessary. Can be referenced from the applications.
Trademarks
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. ISIS and QuickScan are trademarks or registered trademarks of EMC Corporation in the United States. Adobe, the Adobe logo, and Acrobat are either registered trademarks of Adobe Systems Incorporated in the United States and/or other countries. Kofax and VRS are trademarks or registered trademarks of Kofax Image Products, Inc. Other product names are the trademarks or registered trade­marks of the respective companies.
Manufacturer
PFU LIMITED International Sales Dept., Imaging Business Division, Products Group Solid Square East Tower, 580 Horikawa-cho, Saiwai-ku, Kawasaki-shi Kanagawa 212-8563, Japan Phone: (81-44) 540-4538
TOP
Contents
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
All Rights Reserved, Copyright © PFU LIMITED 2008
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
4

Regulatory Information

！
TOP
Contents
Regulatory Information
FCC Declaration
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is located.
• Consult your dealer or an experienced radio/TV technician.
FCC warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The use of a shielded interface cable is required to comply with
！
！
the Class B limits of Part 15 of FCC rules. The length of the Power cable must be 3 meters (10 feet) or less.
Canadian DOC Regulations
This digital apparatus does not exceed the Class B limit for radio noise emissions from digital apparatus set out in the Radio interference Regulations of the Canadian Department of Communications. This Class B digital apparatus complies with Canadian ICES-
003. Le présent appareil numérique n'émet pas de parasites radioélectriques dépassant les limites applicables aux appar­eils numériques de la classe B et prescrites dans le Règle­ment sur le brouillage radioélectrique dictées par le Ministère des Communications du Canada. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Bescheimigung des Herstellers/ Importeurs
Für den fi-6670(A)/fi-6770(A)/fi-6750S wird folgendes bescheinigt:
• In Übereinsstimmung mit den Bestimmungen der EN45014(CE) funkentstört
• Maschinenlärminformationsverordnung 3. GPSGV: Der höchste Schalldruckpegel beträgt 70 dB (A) oder weniger, gemäß EN ISO
7779.
Dieses Gerät wurde nicht für die Benutzung in unmittelbarer Umgebung starker Lichtquellen (z. B. Projektoren) konzipiert.
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
5
Regulatory Information
International ENERGY STAR® Program
As an ENERGY STAR® Partner, PFU LIMITED has determined that this product meets the ENERGY STAR The International ENERGY STAR Program is an international program that promotes energy saving through the penetration of energy effi­cient computers and other office equipment. The pro­gram backs the development and dissemination of products with functions that effectively reduce energy consumption. It is an open system in which business proprietors can participate voluntarily. The targeted products are office equipment such as computers, monitors, printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and logos are uni­form among participating nations.
®
guidelines for energy efficiency.
®
Office Equipment
TOP
Contents
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Use in High-Safety Applications
This product has been designed and manufactured on the assumption that it will be used in office, personal, domestic, regular industrial, and general­purpose applications. It has not been designed and manufactured for use in applications (simply called "high-safety applications" from here on) that directly involve danger to life and health when a high degree of safety is required, for example, in the control of nuclear reactions at nuclear power facilities, automatic flight control of aircraft, air traffic control, operation control in mass-transport systems, medical equipment for sustaining life, and missile firing control in weapons systems, and when provisionally the safety in question is not ensured. The user should use this product with adopting measures for ensuring safety in such high-safety applications. PFU LIMITED assumes no liability whatsoever for damages arising from use of this product by the user in high-safety applications, and for any claims or compensation for damages by the user or a third party.
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
6

Conventions

！
TOP
Contents
Conventions
Symbols Used In This Manual
For notational convention, the following symbols are used in this manual:
This symbol alerts operators to particularly important informa-
！
！
Naming Conventions in This Manual
Scanners:
The scanners are indicated as follows:
fi-6670/fi-6670A ADF type Scanner
fi-6770/fi-6770A/fi-6750S Flatbed type
The explanation in this manual bases on the following models: ADF type: fi-6670 Flatbed type: fi-6770
tion. Be sure to read this information.
This symbol alerts operators to helpful advice regarding opera­tion.
Model Indication
Operating Systems and Software Products:
The OSs and products in this manual are indicated as follows:
Product Indication
Microsoft operating system
Microsoft operating system (32/64-bit)
Microsoft operating system
Microsoft Standard Edition operating system (32/64­bit)
Microsoft operating system (32/64-bit)
Microsoft operating system (32/64-bit)
Microsoft operating system (32/64-bit)
Microsoft operating system (32/64-bit)
Microsoft operating system (32/64-bit)
Microsoft Server 2003
Microsoft
®
Windows® 2000 Professional
®
Windows® XP Professional
®
Windows® XP Home Edition
®
Windows Server™ 2003
®
Windows Vista® Home Basic
®
Windows Vista® Home Premium
®
Windows Vista® Business
®
Windows Vista® Enterprise
®
Windows Vista® Ultimate
®
Office SharePoint™ Portal
®
Office SharePoint™ Server 2007
Windows 2000
Windows XP
Windows Server 2003
Windows Vista
Microsoft SharePoint Server
Windows (*1)
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Adobe
®
Acrobat
®
Adobe Acrobat (*2)
Appendix
Glossary
7
Conventions
*1: Where there is no distinction between the different versions of the
above operating system, the general term "Windows" is used.
*2: All the descriptions in this manual assume the usage of Adobe
Acrobat bundled with this product. However, Adobe Acrobat may be upgraded without notice. If the descriptions differ from the screens actually displayed, refer to the Adobe Acrobat Help.
Arrow Symbols in This Manual
TOP
Contents
Index
Scanner Overview
Right-arrow symbols (D) are used to separate icons or menu options you should select in succession. Example: Click [Tool]
D [Scan Setting].
Screen Examples in This Manual
The screen examples in this manual are subject to change without notice in the interest of product improvement. If the actual displayed screen differs from the screen examples in this manual, operate by following the actual displayed screen while referring to the user's manual of the scanner application you are using. The screen examples used in this manual are of FUJITSU TWAIN 32 scanner driver, FUJITSU ISIS scanner driver, ScandAll PRO (which is an image capturing software), and Adobe Acrobat.
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
8

Precautions

TOP
Contents
Precautions
Liability Note
READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IF THIS PRODUCT IS NOT USED CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS. Also, keep this manual in a safe place so that it can be easily referred to during use of this product. While all efforts have been made to ensure the accuracy of all information in this manual, PFU assumes no liability to any party for any damage caused by errors or omissions or by statements of any kind in this manual, its updates or supple­ments, whether such errors are omissions or statements resulting from negligence, accidents, or any other cause. PFU further assumes no liability arising from the application or use of any product or system described herein; nor any liability for incidental or consequential damages arising from the use of this manual. PFU disclaims all warranties regarding the infor­mation contained herein, whether expressed, implied, or statu­tory.
Use of Mercury
Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state, or federal
g
H
To avoid unexpected injuries:
• Do not put the substance contained in the lamp in your mouth as
it has mercury.
• Do not breathe the chemical liquid contained in the scanner
lamps.
• Do not incinerate, crush, or shred the lamps or scanner parts.
laws.
Maintenance
The user must not perform repairs on this scanner. Contact the store where you purchased the scanner or an authorized FUJITSU Image Scanner service provider to make repairs to this product.
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
9
Precautions
！
Warning Label
TOP
Contents
Index
！
！
HOT warning label:
The glass surface inside the ADF becomes hot during the operation. Be careful not to touch glass surfaces inside the ADF. To avoid burns, never touch around the area indicated by this label.
Take care not to get your finger(s) caught in the ADF while turning.
You must NOT remove this warning label from your scanner. When it gets old or unreadable by staining or scratches, contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider.
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
10

Safety Information

TOP
Contents
Safety Information
This manual describes important details for users to use this product safely and correctly. Read this manual thoroughly before you start using this product. Be sure to read and fully understand the Safety Information, in particular. In addition, keep this manual handy during use of this product, so that you can refer to it quickly when necessary.
Warning Indications Used In This Manual
The following indications are used in this manual to obviate any change of accident or damage to you and/or the product.
This indication alerts operators to an operation
WARNING
CAUTION
A TRIANGLE symbol indicates that special care and attention is required. The drawing inside the triangle shows the specific caution.
A CIRCLE with a diagonal line inside shows action which users may not perform. The drawing inside or under the circle shows the specific action that is not allowed.
that, if not strictly observed, may result in severe injury or death.
This indication alerts operators to an operation that, if not strictly observed, may result in safety hazards to personnel or damage to the product.
Outline characters on a colored background show instructions
R
users should follow. It may also include the drawing that shows the specific instruc­tion.
WARNING
The following are important warnings described in this manual.
Description
Do not damage the power cable.
A damaged power cable may cause fire or electric shock. Do not place heavy objects on power cable, or pull, bend, twist, heat, damage or modify Power cables. Do not use any damaged power cables or power plugs, or install any cables or power plugs to loose wall sockets.
Use only specified power cables and interface cables.
Use only specified power cables and interface cables. Failure to use the correct cables might cause electric shock and/or equip­ment failure. Do not use the power cable provided with the scanner for other devices, since this might cause equipment failure and other troubles or an electric shock.
Make sure to ground the scanner.
Make sure to ground to avoid electric shock. Be sure to ground before plugging into a power outlet. Unplug from the outlet before removing the ground connection.
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
11
Safety Information
Use the scanner only at the indicated power volt­age. Do not connect to multiple-power strips.
Use the scanner only at the indicated power voltage and current. Improper power voltage or current might cause fire or electric shock. Do not connect to multiple-power strips.
Do not touch the power cable with wet hands.
Do not touch the power plug with wet hands. Doing so might cause electric shock.
Wipe off any dust from the power plug.
Wipe off any dust from the metal parts on the power plug or metal fittings with a soft, dry cloth. Accumulated dust might cause fire or electric shock.
Do not install the scanner in a location that has oil smoke, steam, humidity, and dust.
Do not install the scanner in a location subject to oil smoke, steam, humidity, and dust. Doing so might cause a fire or electric shock.
Do not use the scanner if there is a strange odor.
If you detect excessive heat coming from the scanner or detect smoke, strange smells or noises during the operation, immedi­ately disconnect the power plug from the power outlet. Before contacting the store where you bought the scanner or an autho­rized FUJITSU scanner service provider, make sure that any smoke coming from it has completely stopped. Never try fixing such problems by yourself. Doing so is dangerous.
Description
Description
Do not put liquids inside the scanner.
Do not insert or drop any metal objects into the ADF slot or ventilation ports on the scanner. Do not scan any wet documents or documents with paper clips or staples attached. Do not splash or allow the scanner to get wet. If foreign objects (water, small metal objects, liquids, etc.) get inside the scanner, immediately disconnect the power plug from the power outlet. Then, contact the store where you bought the scanner or an authorized FUJITSU scanner service provider. Pay particular attention to this warning in households where there are small children.
Unplug the scanner when a trouble occurs.
Immediately unplug the scanner when a trouble occurs. Never cut the ground connection until the scanner is unplugged from the power outlet.
Do not disassemble the scanner.
Do not take apart or modify the scanner. The inside of the scanner contains high-voltage components. Touching these components might cause electric shock or fire.
Do not use aerosol or alcohol sprays near the scanner.
Do not use any flammable substance or alcohol based cleaning sprays (such as aerosol sprays) to clean the scanner. Sparks, caused by static electricity, generated when blowing off dust and dirt from the outside of the scanner, may cause a fire.
TOP
Contents
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Disconnect the power if the scanner is damaged.
If the scanner is damaged for any reason, immediately discon­nect the power plug from the power outlet. Then, contact the store where you bought the scanner or an authorized FUJITSU scanner service provider.
Do not place the scanner within the reach of small children.
To avoid injuries, do not place the scanner in an area where small children may be able to reach.
Do not touch the heated section for a long time.
Do not touch the heated section such as the bottom of the scanner for a long time. Doing so may cause a low-temperature burn on your skin.
Trouble­shooting
Operational Settings
Appendix
Glossary
12
Safety Information
Do not cover the scanner with something during its operation.
Do not use the scanner while covered with a blanket, etc. Doing so may raise the temperature inside and cause a fire.
Do not use the scanner where it gets wet.
Do not use the scanner at a place such as a bathroom, shower room, or swimming pool where it may easily get wet. Doing so might cause electric shock or fire.
Description
CAUTION
The following are important cautions described in this manual:
Description
Do not install the scanner on an unstable work table.
When installing the scanner on a work table, make sure that the table is flat and level. Place the scanner so that none of its parts extend beyond the edge of the table. Also, it must be strong enough to support the weights of the scanner and other devices.
Firmly insert the power plug.
Firmly insert the power plug into the power outlet as far it can go.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the ventilation ports generates heat inside of the scanner, which may result in fire or scanner failure.
TOP
Contents
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Do not place heavy objects or stand on the top of the scanner.
Do not place heavy objects on the scanner or stand on its top to perform other work. Doing so might cause injuries and equipment failure.
Do not use the scanner immediately after moving it from a cold place into a warm room.
Do not use the scanner immediately after moving it from a cold place into a warm room. Condensation may occur, which might lead to scanning errors. Let the scanner dry for one or two hours before you use it.
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
13
Safety Information
Before moving the scanner, disconnect the power plug from the power outlet.
Do not move the scanner with the power and interface cables connected as this can damage the cables, which can later cause fire, electric shock as well as injuries. Before moving the scanner, be sure to disconnect the power plug from the power outlet, and all other interface cables. Make sure that the floor is free of any obstructions.
Protect the scanner from static electricity.
Install the scanner away from strong magnetic fields and other sources of electronic noise. Also, protect the scanner against any static electricity, which can cause the scanner to malfunc­tion.Choose a static-free place to install the scanner.
Avoid any contact when scanner is in use.
Avoid getting a sleeve, necktie, or hair caught up in any scanner mechanism during scanning since this may cause injuries.
Disconnect the power plug from the power outlet when the scanner is not in use for a long period of time.
When the scanner is not going to be used for a long period of time, be sure to disconnect the power plug from the power outlet.
Description
Description
Before moving the scanner, make sure the trans­port lock is locked. (Flatbed type)
When moving the scanner, be sure to lock the transport lock and the ADF transport lock in order to prevent damage to the scanner.
Handle documents carefully.
When handling documents, be careful not to cut your fingers with them.
Do not make the scanner wet while carrying it outside.
When carrying the scanner outside while it is raining or snowing, pay special attention so the scanner does not get wet.
TOP
Contents
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Do not install the scanner in direct sunlight.
Do not install the scanner under direct sunlight or near heating apparatus. Doing so might cause excessive heat to build up inside the scanner, which can cause scanner trouble or even fire. Install the scanner in a well-ventilated location.
Do not try to move or lift the scanner alone.
When transporting the scanner, never carry it alone.
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
14

Contents

TOP
Contents
Contents
How to Use This Manual ........................................ 2
Introduction ............................................................. 3
Regulatory Information ........................................... 5
Conventions ............................................................ 7
Precautions ............................................................. 9
Safety Information ................................................ 11
Chapter 1 Scanner Overview............................ 20
1.1 Features .............................................................21
Features ...............................................................21
1.2 Scanner Parts and Their Functions ................. 22
fi-6670/fi-6670A (ADF Type) ................................22
fi-6770/fi-6770A/fi-6750S (Flatbed Type) .............24
Model-Common Parts ..........................................27
1.3 Functions of the Operator Panels ....................28
2.2 ADF-Loaded Documents ..................................42
Sizes..................................................................... 42
Paper Quality........................................................ 42
Maximum Document Loading Capacity................ 44
Area Not to be Perforated .................................... 44
Loading Documents with Tabs or Non-Rectangular
Documents ........................................................... 45
Multifeed Detection Conditions............................. 45
Limiting the Background Color Area..................... 46
Job Separation Sheet........................................... 47
2.3 Changing the ADF Position
(Flatbed Type Only) ........................................... 48
2.4 Loading Documents on the Flatbed
(Flatbed Type Only) ........................................... 50
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Operator Panel ..................................................... 28
Indications on the Function Number Display........ 30
1.4 Turning the Scanner ON and OFF ...................31
Turning the Scanner ON ...................................... 31
Turning the Scanner OFF..................................... 31
1.5 Power Save Mode .............................................. 32
Returning from Power Save Mode .......................32
1.6 Basic Flows of Scanning Documents ............. 33
Chapter 2 Loading Documents ........................ 38
2.1 Loading Documents on the ADF ......................39
Chapter 3 How to Use ScandAll PRO .............. 51
3.1 Overview of ScandAll PRO ............................... 52
3.2 Launching ScandAll PRO ................................. 53
3.3 Selecting a Scanner Driver ............................... 54
3.4 Selecting a Scanner Model ............................... 55
3.5 Scan Parameters ............................................... 56
3.6 Scanning Approaches ......................................57
Scanning with [Scan]............................................ 57
Scanning with [Batch Scan].................................. 57
3.7 Scanning with [Scan] ........................................ 58
Consumables
Trouble-
shooting
Operational
Settings
Appendix
Glossary
15
Contents
3.8 Scanning with [Batch Scan] ............................. 61
Creating and Editing Profiles................................ 61
Scanning Documents ...........................................62
[About] Tab........................................................... 72
Chapter 5 Various Documents ......................... 73
5.1 Summary ............................................................ 74
TOP
Contents
Index
Chapter 4 Scan Parameters.............................. 63
4.1 FUJITSU TWAIN 32 Scanner Driver ................. 64
Resolution ............................................................64
Scan Type ............................................................64
Paper Size............................................................ 65
Image Mode .........................................................65
[Scan] Button........................................................ 65
[Preview] Button ...................................................65
[Close]/[OK] Button............................................... 65
[Reset] Button....................................................... 65
[Help] Button......................................................... 65
[About] Button....................................................... 65
[Option] Button .....................................................66
[Advance] Button .................................................. 66
[Config] Button...................................................... 66
4.2 FUJITSU ISIS Scanner Driver ...........................67
[Main] Tab ............................................................67
5.2 Scanning Documents of Different Types or
Sizes .................................................................... 75
Scanning Both Sides of A Document
(fi-6670/fi-6670A/fi-6770/fi-6770A Only)............... 75
Scanning A Large-Size Document or Book
(Flatbed Type Only).............................................. 75
Scanning Documents of Different Widths............. 76
Scanning A Document Longer Than A3 Size....... 77
5.3 Advanced Scanning .......................................... 79
Excluding Color(s) from Images (Dropout Color) . 79
Skipping Blank Pages .......................................... 81
Removing Punch Holes from A Scanned Image.. 82 Scanning A Document from the ADF in Manual
Loading Mode....................................................... 84
Duplex Scanning Using the ADF Virtual Duplex
Function (fi-6750S Only) ...................................... 85
5.4 Setting Post-Scan Operations and Handling .. 87
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
[Layout] Tab .........................................................68
[Image Processing] Tab .......................................69
[Paper Handling] Tab ...........................................69
[Gamma] Tab .......................................................70
[Color Dropout] Tab.............................................. 70
[Blank Page Deletion] Tab.................................... 71
[Compression] Tab ............................................... 71
[Imprinter] Tab ...................................................... 72
Automatically Correcting Skewed Document
Images.................................................................. 87
Setting Auto Correction for Document Page
Orientations.......................................................... 89
Saving Scanned Images in PDF Format.............. 90
Dividing Multipage Documents Using Patch
Codes................................................................... 95
Dividing a Multipage Document Using Barcodes . 97
Trouble-
shooting
Operational
Settings
Appendix
Glossary
16
Contents
Horizontally Splitting a Scanned Image into Two100
Outputting in Multi-Image Mode .........................101
Setting Auto Detection for Content Colors
Temporary Errors ............................................... 133
Device Errors...................................................... 134
8.3 Troubleshooting .............................................. 136
TOP
Contents
Index
(Color/Monochrome) ..........................................103
5.5 Customizing the Hardware Settings .............. 106
Using the Scanner Buttons to Start A Scan
Quickly................................................................ 106
Detecting Multifeeds........................................... 108
Bypassing Multifeed Detection for a Fixed
Format ................................................................ 110
Chapter 6 Daily Care ....................................... 114
6.1 Cleaning Materials and Locations
Requiring Cleaning .........................................115
Cleaning Materials.............................................. 115
Locations to Clean and Cleaning Frequency .....116
6.2 Cleaning the ADF ............................................117
Cleaning with a Cloth Moistened with Cleaner
F1 .......................................................................117
6.3 Cleaning the Flatbed (Flatbed Type Only) ....122
Chapter 7 Consumables ................................. 123
7.1 Consumables and the Replacement
Cycles ...............................................................124
7.2 Replacing the Pick Rollers .............................125
7.3 Replacing the Brake Roller ............................. 127
Chapter 8 Troubleshooting............................. 129
8.1 Paper Jams ......................................................130
8.2 Errors Indicated on the Operator Panel ........132
Scanner cannot be turned on............................. 137
Indication on Function Number Display
goes out.............................................................. 138
Scanning does not start...................................... 139
Quality of scanned pictures or photos is not satisfactory when scanning in black and white... 140 Quality of scanned text or lines is unsatisfactory.141
Images are distorted or blurred. ......................... 142
Vertical lines appear in scanned images............ 143
Function Number Display indicates an error code (alphabetical letter plus number) alternately
after the scanner is turned ON. .......................... 144
Multifeed errors occur frequently........................ 145
Pickup errors occur frequently............................ 147
Paper jams occur frequently............................... 148
Scanned images are elongated when scanned
from the ADF...................................................... 149
There is a shadow on leading edge of scanned
image.................................................................. 150
The scanner is not recognized by your computer
when Kofax VRS is used.................................... 151
8.4 Before Contacting Your Dealer or Scanner
Service Provider .............................................. 152
General Details................................................... 152
Troubles ............................................................. 152
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
17
Contents
8.5 Checking Labels on the Scanner ................... 154
Positions of Labels on the Scanner.................... 154
Chapter 9 Operational Settings...................... 155
9.1 Starting Up the Software Operation Panel .... 156
9.2 Configurable Items .......................................... 157
Device Setting ....................................................157
Device Setting 2 .................................................159
9.3 Settings Related to Consumables and
Useful Life Counters ........................................165
Confirming and Resetting the Counters .............165
Cycle for Cleaning the Scanner [Cleaning Cycle]167 Cycle for Replacing the Consumables
[Useful life counter]............................................. 168
9.4 Settings Related to Scanning .........................169
Adjusting the Starting Position for Scanning
[Offset/Vertical Magnification Adjustment]..........169
Eliminating Shadows or Stripes on the Scanned
Image Edge [Page Edge Filler] ..........................171
Scanning with Particular Color(s) Dropped Out
[Dropout color].................................................... 172
Shorting the Scanning Intervals [Pre-Pick]......... 173
Scan Setting for The Document Whose One Side Is in Dark Background Color [Scan Setting for
Document in Dark Background Color]................ 176
Adjusting the Scanned Document Output Images
[Overcrop/Undercrop]......................................... 177
Adjusting the Paper Picking Pressure
[Pick Pressure] ................................................... 178
9.5 Settings Related to Multifeed Detection ........ 180
Multifeed Detection............................................. 180
Specifying the Multifeed Detection Range [Document Check Area Specification for
Multifeed Detection]............................................ 182
Setting A Non-Multifeed-Detection Range
[Intelligent Multifeed Function]............................ 185
9.6 Settings Related to Wait Time ........................ 186
Timeout for Manual Feeding
[Manual-feed timeout]......................................... 186
Setting the Wait Time in Power Saving Mode
[Power saving].................................................... 187
9.7 Settings Related to Power ON/OFF Control .. 188
Power ON/OFF Control [Power SW Control] ..... 188
TOP
Contents
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Cropping the Image Boundary
[AutoCrop Boundary].......................................... 174
Configuring the Data Transfer Width
[SCSI Bus Width]................................................ 175
Scan Setting for Documents with Tabs or Non-Rect- angular Documents [Scan Setting for Documents
with Tab (Automatic Paper Size Detection)]....... 175
Appendix ........................................................... 189
A.1 Basic Specification ......................................... 190
A.2 Installation Specification ................................ 192
A.3 Outer Dimensions ........................................... 193
ADF type ............................................................ 193
Flatbed type........................................................ 194
A.4 Scanner Options .............................................. 195
Trouble­shooting
Operational Settings
Appendix
Glossary
18
Contents
A.5 Uninstalling the Software ...............................196
Glossary ............................................................ 197
TOP
Contents
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
19
TOP
Contents
Index

Chapter 1 Scanner Overview

This chapter describes the components of the scanner, showing their names and functions, and explains the basics of how to operate them.
Here, Windows Vista screen samples are used to explain the operations. The screens and operations may differ slightly if the OS that you are using is other than Windows Vista. Take note that, when the FUJITSU TWAIN 32 or FUJITSU ISIS scanner driver is updated, the screens and operations herein may also be slightly different. In such case, refer to the relevant manuals or materials, which are to be supplied when updating the driver.
1.1 Features .................................................................................21
1.2 Scanner Parts and Their Functions........................................22
1.3 Functions of the Operator Panels...........................................28
1.4 Turning the Scanner ON and OFF..........................................31
1.5 Power Save Mode...................................................................32
1.6 Basic Flows of Scanning Documents .....................................33
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
Chapter 1 Scanner Overview
TOP
Contents

1.1 Features

This section explains the major features of the scanner.

Features

The scanner has the following features:
Realizes a high-speed scanning of 90 sheets (or 180 pages) per minute under JPEG compression (fi-6670/fi-6670A/fi-6770/fi-6770A only).
The scanner mounts newly-developed high-speed CCD and high-speed image processing circuit. This mechanism has realized a scan speed of 90 sheets or 180 pages (at 200 dpi) per minute. You can perform a batch scanning of about 45,000 sheets per day.
Reduces the work loss caused by multifeeds.
The scanner mounts an ultrasonic multifeed sensor that definitely detects two or more sheets fed simultaneously (this is called a "multifeed"). This feature enables multifeed detec­tion for documents of different thicknesses, sizes, color and/or color density, thus preventing any work loss caused by multi­feeds.
Provides the Intelligent Multifeed function.
The Intelligent Multifeed function recognizes paper (sticky notes or labels) of the same size which are glued onto a pre­specified same location of your document. The function suppresses multifeed detection at this location and continues scanning.
Mounts an adjustable ADF (Flatbed type only).
The scanner is equipped with an adjustable ADF. You can rotate it by 180 degree or slide to a desired position among three, thus saving your installation space.
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
21
Chapter 1 Scanner Overview
TOP
Contents

1.2 Scanner Parts and Their Functions

This section shows you the names of the scanner parts, and briefly describes how they function.

fi-6670/fi-6670A (ADF Type)

ADF (Automatic Document Feeder)
Feeds documents to the scanning position automatically. Documents are fed sheet by sheet when loaded for batch scanning. Both sides of documents can be scanned at one time.
Stacker
Scanned documents are ejected from the ADF onto this stacker. You can adjust the height of the stacker at lower or upper position. Is removable.
Stacker Extension
Pull out this extension according to the document length.
Stopper
Raise this if the documents loaded are long.
EXT Connector
A connector for connecting to the imprinter option. For details of the imprinter option, refer to the "Imprinter Operator’s Guide."
Operator Panel
Comprises a Function Number Display, operating push buttons, and LEDs. Used to operate the scanner and monitor the status. Two panels are mounted; one each on each side. You can use whichever is convenient for you. The panels are of quick-open type, and can be folded back in place when not used.
ADF Paper Chute
Holds in place the document pages/sheets that are to be fed into the ADF. Load them with their face
Paper Chute Extension
Extended when scanning long documents.
Chute Roller Cover
A cover to prevent your finger(s) from being caught by the Chute Roller.
Side Guide
Prevents documents from being skewed during feeding. Adjust the guide to the width of the document loaded.
Side Guide Button
Adjusts the position of the Side Guide when kept pressed. Locks the Side Guide at the position when this button is released.
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
down.
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
22
Chapter 1 Scanner Overview
ADF Open Button (Common)
Opens the ADF. Push the buttons in to open the ADF.
Cable Cover (Common)
A cover to house the cablings inside to protect them. The cables are let out from either side of the cover to avoid tangling.
CGA Board Slot (fi-6670 only)
Remove the cover to install a CGA or optional board. The fi-6670A mounts a CGA board. For details of the CGA board, refer to "A.4 Scanner Options" (on page 195).
TOP
Contents
Index
Scanner Overview
Loading Documents
fi-6670
fi-6670A
Main Power Switch (Common)
Used to turn the scanner ON and OFF.
Power Connector (Common)
A connector for a power cable.
Ventilation Port (Common)
An open port for ventilating hot air from inside the scanner.
SCSI Connector 1 (Common)
A connector for a SCSI interface cable.
SCSI ID Switch (Common)
Used to configure a SCSI ID (ID=5 by factory setting).
USB Connector 1 (Common)
A connector for a USB interface cable.
CGA Board (fi-6670A only)
For details of the CGA board, refer to "A.4 Scanner Options" (on page 195).
USB Connector 2 (fi-6670A only)
A connector for a USB interface cable.
SCSI Connector 2 (fi-6670A only)
A connector for a SCSI interface cable.
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
23
Chapter 1 Scanner Overview

fi-6770/fi-6770A/fi-6750S (Flatbed Type)

TOP
Contents
Index
ADF (Automatic Document Feeder)
Feeds documents to the scanning position automatically. Documents are fed sheet by sheet when loaded for batch scanning. The fi-6770/fi-6770A can scan both sides of documents at one time.
Stacker Extension
Pull out the extension according to the document length.
Stopper
Raise it if the documents loaded are long.
Stacker
Scanned documents are ejected from the ADF onto this stacker. You can adjust the height of the stacker at lower or upper position. Is removable.
Flatbed
Place them on the glass sheet by sheet for manual scanning. Allows for scanning thick documents such as books.
Transport Lock
Locks the carrier unit inside the Flatbed during transportation. Use a coin or similar to unlock it. Turn the slot to a vertical position to release the lock; to a horizontal position to lock it.
Side Guide Button
Adjusts the position of the Side Guide when kept pressed. Locks the Side Guide at the position when this button is released.
ADF Open Button
Opens the ADF. Push the buttons in to open the ADF.
ADF Paper Chute
Holds in place the document pages/sheets that are to be fed into the ADF. Load them with their face down.
Paper Chute Extension
Extended when scanning long documents.
Chute Roller Cover
A cover to prevent your finger(s) from being caught by the Chute Roller.
Operator Panel
Used to operate the scanner and monitor the status. Comprises a Function Number Display, operating push buttons, and LEDs.
Side Guide
Prevents documents from being skewed during feeding. Adjust the guide to the width of the documents loaded.
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
24
Chapter 1 Scanner Overview
Lock Screw Storage Hole
Stores the ADF Lock Screws that were removed after the ADF has been unlocked.
ADF Lock Screw
Fixes the ADF.
Document Cover
Holds the loaded documents at the scanning position when closed.
Handle
Used to open and close the Document Cover.
TOP
Contents
Index
Scanner Overview
Loading Documents
Document Bed
Place documents on the glass when scanning through the flatbed.
The Document Cover with a black document holding pad is optionally available. This type is convenient for scanning documents in black background when loading them from the flatbed. This option allows you to correct skewed document images after scanned with the flatbed and to recognize the size of document to output at it original size. Name: Black Document Pad Parts No.: PA03338-D960
Document Holding Pad
Holds documents to the Document Bed.
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
25
Chapter 1 Scanner Overview
fi-6770
Main Power Switch (Common)
Used to turn the scanner ON and OFF.
Power Connector (Common)
A connector for the power cable.
Ventilation Port (Common)
An open port for ventilating hot air from inside the scanner.
CGA Board Slot (fi-6770 only)
Connects a CGA board. For details of the CGA board, refer to "A.4 Scanner Options" (on
page 195).
TOP
Contents
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
fi-6770A
fi-6750S
SCSI ID Switch (fi-6770/fi-6770A only)
Used to configure a SCSI ID (ID=5 by factory setting).
SCSI Connector 1 (fi-6770/fi-6770A only)
A connector for a SCSI interface cable.
CGA Board (fi-6770A only)
For details of the CGA board, refer to "A.4 Scanner Options" (on
page 195).
USB Connector 2 (fi-6770A only)
A connector for a USB interface cable.
SCSI Connector 2 (fi-6770A only)
A connector for a SCSI interface cable.
USB Connector 1 (Common)
A connector for a USB interface cable.
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
26
Chapter 1 Scanner Overview

Model-Common Parts

TOP
Contents
Index
Pick Arm (x1)
Ultrasonic Sensor (x2)
(for multifeed detection)
Sheet Guide (x2)
Glass (x2)
Brake Roller (x1)
(consumable)
Brake Roller Holder (x1)
Feed Roller (x4)
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Plastic Roller (x4)
Various Documents
Daily Care
Pick Roller (1 x 2 types)
(consumable)
Chute Roller (x1)
(usually covered with a hood)
Pick Roller Cover (x1)
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
27
Chapter 1 Scanner Overview
TOP
Contents

1.3 Functions of the Operator Panels

The Operator Panel Consists of a Function Number Display, operating push buttons, and LEDs.

Operator Panel

fi-6670/fi-6670A (ADF Type)
Two Operator Panels are mounted on the scanner; one each on each side. You can use whichever is convenient for you. They can be folded back in place when not used.
Check LED
Lights in orange when an error occurs.
Function Number Display
Indicates the function number and the scanner status.
[Function] Button
Switches the Function activated by the [Send to] button.
[Power] Button / Power LED
Turns the scanner ON and OFF. Lights in green when the scanner is turned ON.
Check
Function
Send to
Scan / Stop
Power
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
When the Operator Panel is folded back in place
LED
The scanner status can be checked while the Operator Panel is folded back in place. Lights in green when the scanner is turned ON. Lights in orange when en error occurs.
For details of how to scan documents using the [Scan/Stop] or [Send to] button, refer to the FUJITSU TWAIN 32 Scanner Driver Help included in the SETUP DVD-ROM, and the section
"Using the Scanner Buttons to Start A Scan Quickly" (on page
106).
[Scan/Stop] Button
Launches linked application software for scanning, etc. Resets the error indication. Cancels ongoing scanning.
[Send to] Button
Launches linked application software for scanning, etc. Resets the error indication.
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
28
Chapter 1 Scanner Overview
fi-6770/fi-6770A/fi-6750S (Flatbed Type)
Check
Function
Send to
Scan / Stop
Power
Check LED
Lights (in orange) when an error occurs.
Function Number Display
Indicates the function number and the scanner status.
[Function] Button
Switches the Function activated by the [Send to] button.
[Send to] Button
Launches linked application software for scanning. Resets an error indication.
[Scan/Stop] Button
Launches linked application software for scanning. Resets an error indication. Cancels ongoing scanning.
TOP
Contents
Index
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
For details of how to scan documents using the [Scan/Stop] or [Send to] button, refer to the FUJITSU TWAIN 32 Scanner Driver Help included in the SETUP DVD-ROM, and the section
"Using the Scanner Buttons to Start A Scan Quickly" (on page
106).
[Power] Button / Power LED
Turns the scanner ON and OFF. Lights (in green) when the scanner is turned ON.
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
29
Chapter 1 Scanner Overview

Indications on the Function Number Display

TOP
Contents
Index
Indication Explanation
8 Blinks only one time upon turning on the scanner.
P Indicates that the scanner has been turned ON and is
being initialized.
1 Indicates that initialization has ended successfully. This
status is called "Ready Status" in which you can perform a scan.
J U
E F C H A L
Indicates that a recoverable error occurred during scan­ning. "J" or "U" and an "error number" are displayed alternately. For error details, refer to "Temporary Errors" (on page
133).
After the error has been resolved, you can return to the Ready Status (see "1" above) by pressing the [Stan/Stop] or [Send to] button.
Indicates that an abnormality (device error) occurred in the scanner during its initialization or during scanning docu­ments. "E", "F", "C", "H", "A", or "L" and an "error number" are dis­played alternately. For details of the errors, refer to "Device Errors" (on page
134).
If this error occurs, turn the Main Power Switch OFF and then ON again. If the error persists after this, contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider.
Scanner Overview
Loading Documents
How to Use ScandAll PRO
Scan Pa­rameters
Various Documents
Daily Care
Consumables
Trouble­shooting
Operational Settings
Appendix
Glossary
30
Loading...
+ 182 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use