Frigidaire CFEH3054USA, CFEH3054USB, CFEH3054UWA, CLEH3054UFA, CLEH3054UFB Installation Guide

INSTALLATION INSTRUCTIONS

FRONT CONTROL FREESTANDING ELECTRIC RANGE

INSTALLATION AND SERVICE MUST BE

PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

United States

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Canada

IMPORTANT SAFETY INSTRUCTIONS

If the information in this manual is not followedexactly,afireorelectricalshockmayresultcausing property damage, personal injury or death.

Important Notes to the Installer:

•Read all instructions contained in these installation instructions before installing range.

•Remove all packing material from the oven compartments before connecting the gas & electrical supply to the range.

•Observe all governing codes and ordinances.

•Be sure to leave these instructions with the consumer.

Important Notes to the Consumer:

Keep these instructions with your owner’s guide for future reference.

•As when using any appliance generating heat, there are certain safety precautions you should follow.

These are listed in the Use & Care Guide, read it carefully.

•Be sure your range is installed and grounded properly by a qualified installer or service technician.

•Make sure the wall coverings around the range can withstand the heat generated by the range.

•To eliminate the need to reach over the surface elements, cabinet storage space above the elements should be avoided.

Tip Over Hazard

• A child or adult can tip the range and be killed.

• Verify the anti-tip device has been installed to floor or wall.

•Ensure the anti-tip device is re-engaged to floor or wall when the range is moved.

•Do not operate the range without the anti-tip device in place and engaged.

•Failure to follow these instructions can result in death or serious burns to children and adults.

Range

leveling leg

Anti-tip bracket

To check if the anti-tip bracket is installed properly, use both arms to grasp the rear edge of the range back. Carefully attempt to tilt range forward. When properly installed, the range should not tilt forward.

Refer to the anti-tip bracket installation instructions supplied with your range for proper installation.

P/N 809127102 (1801) Rev. A English – pages 1-6 Français – pages 7-12

1

30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

1.Clearances and Dimensions

a.Provide adequate clearances between the range and adjacent combustible surfaces.

b.Location—Check location where the range will be installed. Check for proper electrical supply and the stability of floor.

c.Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level.

Front	Typical cabinet installation					Side
view						view
									29 7/8"
			30”
			Minimum
Minimum to		1”	30” Minimum*		Minimum to		13”
wall on either				18”
					cabinets on	Maximum depth
side of range								36 5/8"
					either side	for cabinets
above 36” height.					of range	above range top.		± 1/4"
						25” Max.		Maximum
36”
			30”						26 6/8"
				0” clearance below cooking top and at rear of range
Fig.1			Minimum
									Door	47"
										open
								Fig.2
*30" (762 mm) MINIMUM CLEARANCE BETWEEN THE										BACK
TOP OF THE COOKING SURFACE AND THE BOTTOM										VIEW
OF AN UNPROTECTED WOOD OR METAL CABINET; OR
24" (610 mm) MINIMUM WHEN BOTTOM OF WOOD OR									All dimensions for electrical outlet location
METAL CABINET IS PROTECTED BY NOT LESS THAN									are maximum.
1/4" (6 mm) FLAME RETARDANT MILLBOARD COVERED
WITHNOTLESSTHANNO.28MSGSHEETSTEEL,0.015"									Dashed cubed area
(0.4 mm) STAINLESS STEEL, 0.024" (0.6 mm) ALUMINUM									shows where the electrical outlet must be
									installed
OR 0.020" (0.5 mm) COPPER. 0" (0 mm) CLEARANCE IS									for flush to the wall installation.
THEMINIMUMFORTHEREAROFTHERANGE.FOLLOW								11”
ALL DIMENSION REQUIREMENTS PROVIDED ABOVE
								(279 mm)
TO PREVENT PROPERTY DAMAGE, POTENTIAL FIRE								22”
HAZARD,ANDINCORRECTCOUNTERTOPANDCABINET								(559 mm)
CUTS.

		6”
TO ELIMINATE THE RISK OF BURNS OR FIRE BY		(152 mm)
		Wall
REACHING OVER HEATED SURFACE UNITS, CABINET
STORAGESPACELOCATEDABOVETHESURFACEUNITS		Edge
	2-5/8” (67 mm) for models
SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE	equipped with warmer drawers
PROVIDED,THERISKCANBEREDUCEDBYINSTALLING	3-1/2” (89 mm) for models
	equipped with storage drawers	Fig.3
A RANGE HOOD THAT PROJECTS HORIZONTALLY A
MINIMUM OF 5" (127 mm) BEYOND THE BOTTOM OF
THE CABINETS.

2

30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

2. Tools You Will Need

For leveling legs and Anti-Tip Bracket:

• Adjustable wrench or channel lock pliers

• 5/16" Nutdriver or Flat Head Screwdriver

•Electric Drill & 1/8" Diameter Drill Bit (Masonry Drill Bit if

installing in concrete)

• Level & Measuring Tape

For electrical supply connection:

• 1/4" & 3/8" Socket driver or Nutdriver Additional Materials You Will Need:

• Power Supply Cord or

• Copper Electrical Wiring & Metal Conduit (for hard wiring)

3. Anti-Tip Bracket Installation

Instructions

Important Safety Warning

To reduce the risk of tipping of the range, the range should be secured to the floor by properly installed anti-tip bracket and screws packed with the range. Failure to install the anti-tip bracket will allow the range to tip over if excessive weight is placed on an open door or if a child climbs upon it. Serious injury might result from spilled hot liquids or from the range itself.

If range is ever moved to a different location, the anti-tip brackets must also be moved and installed with the range.

Instructions are provided for installation in wood or cement fastened to either the floor or wall. When installed to the wall, make sure that screws completely penetrate dry wall and are secured in wood or metal. When fastening to the floor or wall, be sure that screws do not penetrate electrical wiring or plumbing.

A.LocatetheBracketUsingtheTemplate-(Bracketmaybe located on either the left or right side of the range. Use the information below to locate the bracket if template is not available). Mark the floor or wall where left or right sideoftherangewillbelocated. Ifrearofrangeisagainst the wall or no further than 1-1/4" (32 mm) from wall when installed, you may use the wall or floor mount method. If molding is installed and does not allow the bracket to fit flush against the wall, remove molding or mount bracket to the floor. For wall mount, locate the bracket by placing the back edge of the template against the rear wall and the side edge of template on the mark made referencing the side of the range. Place bracket on top of template and mark location of the screw holes in wall. If rear of range is further than 1-1/4" (32 mm) from the wall when

installed, attach bracket to the floor. For floor mount, locate the bracket by placing back edge of the template where the rear of the range will be located. Mark the location of the screw holes, shown in template.

B.Drill Pilot Holes and Fasten Bracket - Drill a 1/8” (3 mm) pilot hole where screws are to be located. If bracket is to be mounted to the wall, drill pilot hole at an approximate

20° downward angle. If bracket is to be mounted to masonry or ceramic floors, drill a 5/32” (4 mm) pilot hole 1-3/4” (44 mm) deep. The screws provided may be used in wood or concrete material. Use a 5/16” (8 mm) nutdriver or flat head screwdriver to secure the bracket in place.

(32 mm)

Fig.4

(32 mm)

Fig.5

3

30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

C.LevelandPositionRange-Levelrangebyadjustingthe(4) leveling legs with a wrench. Note:A minimum clearance of 1/8” (3 mm) is required between the bottom of the range and the leveling leg to allow room for the bracket. Use a spirit level to check your adjustments. Slide range back into position. Visually check that rear leveling leg is inserted into and fully secured by the Anti-Tip Bracket by removing lower panel or storage drawer. For models with a warmer drawer or broiler compartment, grasp the top rear edge of the range and carefully attempt to tilt it forward.

(17 mm)

Fig.6

3. Electrical Connection

Requirements

Avoid fire hazard or electrical shock. Failure to follow this warning may cause serious injury, fire, or death.

Plugtherangepowercable(4conductors)intoa4conductor range outlet. Outlet must be properly grounded and in accordancewiththeCanadianElectricalCode(CSAStandard (C22.1 Part 1 -- latest edition) -- and any local electrical code requirements.

Locate outlet 6" (152 mm) above the floor in the wall behind the range.

Grounding Instructions

Forpersonalsafety,thisappliancemustbeproperlygrounded. Formaximumsafety,thepowercordmustbepluggedintoan electrical outlet that is correct voltage, is correctly polarized and properly grounded in accordance with local codes.

Power supply cord with 4-prong

grounding plug 240V grounded wall receptacle

Fig.7

It is the personal responsibilty of the consumer to have the appropiate outlet with the correct, properly grounded wall receptacle installed by a qualified electrician.

4. Model and Serial Number

Location

The serial plate is located on the right-hand surface of the oven front frame at the storage or warmer drawer; or the lower panel area.

Whenorderingpartsforormakinginquiresaboutyourrange, always be sure to include the model and serial numbers and a lot number or letter from the serial plate on your range.

Your serial plate also tells you the Kilowatt rating (power requirements) and Voltage ratings.

Serial Plate Locations:

Serial plate is located on the lower right front frame of the appliance. Alternate location may be under cooktop. Fig.8

4