Farfisa Echos, Exhito, Compact User Manual
ELECTRONIC
CALL SYSTEM
TECHNICAL
MANUAL
2012
ECHOS
EXHITO
COMPACT
INTRODUCTION
Notice to the installer and user
This edition contains helpful information on the operation and installation of Farfisa video intercoms systems.
In order to make the systems work properly it is necessary to install only
Farfisa equipment, keeping strictly to the items referred to in each
diagram.
Read all the notes carefully, (even the small ones) in each installation
scheme and the working instructions of the system given in the
following pages.
For the sake of clarity, please notice that the sequence of the terminals
of each article
has not been followed. Only the terminal code (letter and/
or number) is valid not the graphic sequence.
The items may have more terminals than the ones in the installation
diagrams. The excess terminals must not be used.
Check the integrity of the product after removing it from the packing.
Packing materials (such as plastic bags, cardboard, polystyrene
foam, etc.) must be kept out of the reach of children.
The manufacturer cannot be held responsible for possible damages
caused by improper, erroneous and unreasonable use.
The cable runs of any intercom and video-intercom system must be
kept separate from the mains or any other electrical installation as
required by International Safety Standards.
WARNINGS
An all-pole mains switch with a contact separation of at least
3mm in each pole shall be incorporated in the electrical installation of the building.
Before connecting the unit, make sure its data correspond to
those of the mains.
The apparatus shall not be exposed to dripping or splashing.
For correct operation make sure that ventilation or heat dissipation openings are not obstructed.
Do not open or tamper with power supply or video intercom
apparatus when they are ON. There is high voltage inside.
European Mark of conformity to the EEC
Directives.
CE MARK
The CE mark ensures that the product complies with the requirements of the
European Community Directives in force; in particular, Electrical Safety LVD73/23,
Electromagnetic Compatibility EMC89/336 and Telecommunication Terminals
R&TTE99/5 Directives.
As set forth by the Directives, the technical documentation and Conformity Declarations are available in the Company’s offices for verifications and controls by
competent Authorities.
Avoid bumping and hitting the video intercom apparatus, it
could break of the CRT with consequent projections of fragmented glass.
For installation or maintenance refer only to qualified personnel.
Mark of VDE a German Testing and Certification Institute.
R
T
E
I
C
F
I
C
M
A
E
T
T
I
S
O
Y
N
S
I
S
O
9
0
0
1
:
2
0
0
SGS
0
Quality assured firm.
Italian Association of Electrotechnical and
Electronic Industries
11
TECHNICAL MANUAL
2012 edition
INDEX
General characteristics
Intercom/videointercom systems with reduced wires technology
- Internal stations
- External door stations
- Power supplies and service modules
- Installation instructions
- Installation diagrams
- intercoms
- intercommunicating intercoms
- videointercoms
- intercommunicating videointercoms
Traditional intercoms and videointercoms
- Internal stations
- External door stations
- Power supplies and service modules
- Installation instructions
- Installation diagrams
- intercoms
- intercommunicating intercoms
- videointercoms
- additional diagrams
Page
2
3
4
16
47
51
53
54
65
68
88
93
94
113
141
146
151
152
164
185
219
Product List
230
1
(MT11 - Gb2012)
GENERAL CHARACTERISTICS
s
Exhito
Compact
Studio
Project
Agorà
Profilo
Matrix
Mody *
UP **
1+1 4+1 4+1 7+1
VIDEO-
INTERCOMS INTERCOMS
Serie
Internal stations
Echos *
External door stations
The Farfisa electronic call system with reduced
wires technology allows for the realisation of
intercom, video intercom and intercommunicating systems.
The modularity of Farfisa indoor and outdoor
devices allows for system extension to satisfy
the most diverse user’s requirements, from
individual houses to apartment buildings, from
simple intercoms to complete videointercoms.
Selecting the system
The first choice to be made is the preferred
type of system.
• Analog system with reduced number of
conductors (1+1 intercoms: 1 common
wire +1 wire for each user; 4+1 videointer-
coms: 4 common wires +1 wire for each
user).
• traditional analog system (4+1 intercoms:
4 common wires +1 wire for each user; 7+1
videointercoms: 7 common wires +1 wire
for each user + coaxial cable).
The Farfisa electronic call system allows for the
realisation of different types of installation.
• Intercom systems with 1 or more main
entrances and with or without secondary
entrances
• Videointercom systems with 1 or more
main entrances and with or without secondary entrances
• Intercommunicating systems
• Mixed systems (intercoms/videointer-
coms/intercommunicating systems)
• Intercom systems
It is the simplest of the installations. It provides
bidirectional audio communication between
intercoms and external door stations with dooropening function.
The following variants of the basic installation
are possible:
-intercommunicating service. It allows for
communication between different intercoms
of the same apartment or between different
apartments with private conversation to other
users and to external stations
-private conversation. By adding a board to
each intercom you can restrict the communication between internal and external user to
the called user. The other users do not hear
the conversation in progress when they lift the
handset.
• Videointercom systems
Apart from audio communication and dooropening function, video intercom systems provide visual control of the entrance.
The typical characteristics of video intercom
systems are:
-Timed operation. The video intercom of the
called user is enabled for about 100 seconds.
Picking-up the handset the enabling time will
be doubled; hanging up the handset the system switches back to the stand-by mode.
Systems which are using the power supplytimer art.1181E and 1281E switch back to the
stand-by mode only when the enabling time
expires.
-Private conversation. Video intercom systems allow for audio communication only for
the called user. The other users do not hear
the conversation in progress when they lift the
handset.
-Intercommunicating service. This service
allows for audio communication between different intercoms or video intercoms of the
same apartment or between different apartments with private conversation to other users
or external stations.
-Control switching ON. The user can enable
the system, switch ON his/her own video intercom and monitor the area framed by the camera. Additional wires and activation buttons
are needed in case of multiple entrances.
• Mixed systems (intercoms/videointer-
coms/intercommunicating systems)
All intercom and video intercom systems can
be combined according to the user’s requirements.
Selecting the articles
When choosing the article and type of installation, you should consider:
• user’s requirements
• number of users
• installation possibilities
• possible location of articles
The following options are possible for external
door stations and internal stations:
• External door stations:
- Agorà series
- Profilo series
- Matrix series (steel push-button panels)
- Mody series
- UP series
• Internal stations:
- Echos series
- Exhito series
- Compact series
- Studio series
- Project series
Table for the selection of house’s devices
and door stations according to the
performances of the system (see paragraph
“Selecting the system”)
Graphic symbols
The following symbols are used in the installation diagrams:
Speaker
Microphone
Button
Resistance
Lamp
Diode
Electronic buzzer
SR41
Additional speaker
Electric door lock
Coaxial cable
Optional wire (usually control switching ON, door release button or intercommunicating calls)
Dashed line (for schematic purposes
the first and last monitors are shown in
the multi-family systems. Required
additional monitors can be inserted in
such dashed line to complete the installation).
xn
Call wires (second and last)
x2
2
(MT11 - Gb2012)
* For audio compatibility we do not suggest to
connect door stations MODY series with
internal devices ECHOS series.
** Series for up to 2 calls
INTERCOMS AND VIDEOINTERCOMS SYSTEMS
REDUCED WIRES TECHNOLOGY
INDEX
Internal stations
- Echos series videointercoms
- Exhito series videointercoms
- Exhito series intercoms
- Compact series videointercoms
- Compact series intercoms
- Project series intercoms
External door stations
- Agorà series push-button p anels
- Profilo series push-button panels
- Matrix series push-button panels
- Mody series push-button panels
Power supplies
Service modules
Installation instructions
Working instructions
Installation diagrams
Page
4
4
9
11
14
15
15
16
16
22
31
38
47
47
50
52
53
3
(MT11 - Gb2012)
INTERNAL STATIONS
XL+
F
EH9161
1181E
Orange
ECHOS SERIES
1+1
VIDEOINTERCOMS
INTERCOMS *
16
5
”
/
8
4+1
VIDEOINTERCOMS
EH9161CT. Hands Free Colour Videointercom with audio-video
privacy, 3 types of calls, 5 differentiated programmable ring tones,
audio, contrast, and brightness adjustment. Metallized grey colour.
Complete with 10 keys for monitor control switching-on, door lock
opening, intercom calls and supplementary services. It can be installed
on the wall by using the back box art.9083 or wall adaptor WA9100T.
EH9161CW. Hands-free videointercom with same features as
above, in white colour finish. It can be installed on the wall by using the
back box art.9083 or wall adaptor WA9100W.
Technical characteristics
Power supply: 18÷24Vdc
Operating current: 0.4A
Screen: 3.5" LCD
Television standard: PAL
Horizontal frequency: 15625Hz
Vertical frequency: 50Hz
Band width: >5MHz
Video signal: balanced
Starting up time: 1 second
Number of bell rings: 2 (programmable)
Operating temperature: 0°÷+50°C
Maximum admissible humidity: 90%RH
208
8
3
”
/
16
26
1
How to select the function for buttons from 1 to 6
Buttons from 1 to 6 can be used for several functions, that is:
- intercommunicating calls;
- control switching ON of the video intercom when more than one
external door station or extra surveillance cameras are present on
the system;
- free voltage contacts for supplementary functions.
103
1
”
/
4
16
ATTENTION. The common contacts of the buttons are only two: one
for the buttons 1 and 2, the other for the buttons 3,4,5 and 6, so at
least only two of the three possible different operations described
before can be achieved at the same time. When the buttons are used
for intercommunicating calls or videointercom control switching ON
”
the terminals 1C and 2C must remain unconnected.
Functions of buttons according to the position of jumpers J11 and
J12
Push-buttons Jumpers Position Function
1-2 intercommunicating calls
1, 2 J12 2-3 (*) control switching ON
free free contacts (common 1C)
1-2 intercommunicating calls
3, 4, 5, 6 J11 2-3 (*) control switching ON
free free contacts (common 2C)
(*) Factory setting
1 - 2
Intercommunicating calls
2 - 3
Control switching ON
E
C
H
O
S
Terminals
X Balanced negative video signal input
Y Balanced positive video signal input
F Ground
H Positive voltage input (18-24Vdc)
10 Call, audio reception/transmission, door releasing
4 Control switching ON (button
9R Electronic call input from other intercommunicating devices
A1 Electronic floor call input
L+ LED for open-door signalling or other functions
V+ Positive voltage input for intercommunicating devices (15÷18Vdc)
1C Common contact for buttons P1 and P2
P1 - P2 Service buttons (max 50mA)
2C Common contact for buttons P3, P4, P5 and P6
P3 ÷ P6 Service buttons (max 50mA)
C Electronic call input for intercommunicating calls (common contact
for buttons P1÷P6 determined by the position of the jumpers J11
and J12)
)
Free
Free contacts commons 1C and 2C
Supplementary functions
Floor call
For floor call feature make the connection as reported on page 87.
Door-open’s warning and other functions
For door-open’s warning or other similar functions connect a normally
closed contact (NC) of a sensor or a relay between the terminal L+ of the
videointercom and terminal X of power supply 1181E .
Closed contact the orange LED is ON.
Open contact the orange LED is OFF.
4
(MT11 - Gb2012)
INTERNAL STATIONS
Flush mounted version
9083. Back-box for video intercoms
EH9161CT and EH9161CW.
4’ 11”
192
7
1+1
INTERCOMS *
92
3
46
13
”
/
1
16
5
”
/
8
4+1
VIDEOINTERCOMS
9
”
/
16
4 - Plug-in back the terminal blocks on the video intercom paying
attention to their position and direction in order to avoid degradation
of the system.
1 -Wall-up the back box art.9083 at an height of about 1.5 meters above
the floor.
2 -Unplug the terminal block from the video intercom.
5 -Remove the two frontal plastic frames to approach the two fixing
points of the video intercom.
E
C
H
3 -Make the connections as required by the elec-
tric diagram to wire. If the system provides for
the use of the buttons from 1 to 6, move the
jumpers J11 and J12, located on the back of
the video intercom, according to the required
function (see table on page 4).
O
S
6 -Fix the video intercom to the back box using the two screws supplied
with the product.
5
(MT11 - Gb2012)
INTERNAL STATIONS
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
7 -Re-insert the two frontal plastic frames to the video intercom.
Surface mounted version
WA9100T. Wall adaptor for the EH9161CT videointercom.
WA9100W. W all adaptor for the EH9161CW videointercom.
Table version
TA9160. Table adapter for Echos videointercoms. Complete with
junction box and 2.4m connection cable with 20 wires.
WA9100T/W
TA9160
Junction box
1 -Fix the adapter to the wall with 4 expansion plugs at approx. 1.5m
from the floor.
E
C
X
Yellow
- Fix the wall adaptor
WA9100T or WA9100W
to the table adaptor using
the supplied nuts.
- Insert the cable in the
proper hole of the adaptor
and fix it.
- Make the connection on
the videointercoms
terminal boards and write
down the correspondence between terminals and wire’s colour on the
label on the junction box.
- Fix the videointercom as shown in the figure 2 of this page.
H
F
EH9161..
Y
X
Display adjustment
To optimize the angle of view of the display it can be adjusted up and
down for about 15°.
X
Y
H
O
S
2 -Fix the video intercom to the wall adaptor using the two screws
supplied with the product.
6
(MT11 - Gb2012)
INTERNAL STATIONS
Characteristics
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
1
Image brightness adjustment .
2
Loudspeaker. It allows to hear the conversation and to receive the calls from the
external door station, from other intercommunicating equipments or from local door
station.
3
Call and communication volume adjust-
ment
4
Microphone. It allows to talk with the door
station or with other intercommunicating
equipments
5
Green LED. The LED shows:
- a communication in progress when it
lights up continuously;
- an intercommunicating call when it flashes.
6
Control switching ON button . It allows to power ON the video intercom and
monitoring the entrance.
7
Mute button . It allows to:
- enable/disable the audio (microphone)
to the door station during a conversation;
- enable/disable the bell rings if pressed
for less then 2 seconds after receiving a
call or making a control switching ON function;
- enter/exit the programming mode if
pressed for more than 2 seconds.
8
Red LED. The LED shows:
- temporary disabling of audio when it continuously lights-up. If audio is enabled again
the LED recover the previous operating
mode;
- bell rings disabling. The LED flashes
when a call is received and during the
.
conversation with an external door station
or another intercommunicating equipment;
- the videointercom is in programming operation mode when it is continuously lit-up.
9
Audio communication button . It al-
lows to enable the audio communication
with the door station or another intercom
after receiving a call or a control switching
ON operation (
cation is end pressing again the button or if
the communication time expires.
10
Buttons 3,4,5 and 6 are available for supple-
mentary services. After positioning properly the jumper J11 they can be used for:
- intercommunicating calls;
- control switching ON function for multiple
entrance systems;
- as free voltage contacts (max 50mA).
These four buttons, having a shared common contact (terminal 2C), can be only
used for one of the functions listed above at
time.
11
Lock release button . It allows to operate the electric lock release either with the
video intercom in ON or OFF state.
12
Buttons 1 and 2 are available for supplementary services. After positioning properly the jumper J12 they can be used for:
- intercommunicating calls;
- control switching ON function for multiple
entrance systems;
- as free voltage contacts (max 50mA).
These four buttons, having a shared common contact (terminal 1C), can be only
used for one of the functions listed above at
time.
13
Orange LED. The LED lights-up when at
the terminal L+ is connected a positive
voltage (8÷12Vdc). To signal an open-door
). The audio communi-
state it is necessary to install to the door a
proper sensor whose contacts must be a
normally closed type (see page 4).
14
3.5" Colour LCD Display.
15
Jumpers for programming buttons 1 to
6.
16
Microphone sensitivity adjustment
MIC.SENS.
17
Colour adjustment .
18
Contrast adjustment .
Adjustment of the microphone ampli-
.
fier
17 18 1915 16
E
C
H
O
S
7
(MT11 - Gb2012)
INTERNAL STATIONS
1+1
ADJUSTMENTS
Brightness adjustment.
INTERCOMS *
With the video intercom switched ON, press
left and right the button
brightness of the image. T o store the current
setting press the button
this button switches OFF the video intercom.
Colour
4+1
The trimmers are located on the back of the
video intercom and can be operated by
means of a small screwdriver. T o adjust the
VIDEOINTERCOMS
trimmers is required:
-dismount the video intercom from the wall to
accede to the adjustment points;
-power ON the video intercom;
-insert the screwdriver in the hole marked
with the symbol of the adjustment required;
-rotate the screwdriver clock or anti-clock
wise to find the desired image quality;
-fix again the video intercom to the wall.
Enabling, disabling and volume of the
ringing sound.
When you receive a call from the door station
or from another intercommunicating
equipment it is possible to adjust the level of
the ringing sound pressing left and right the
button
the button
T o disable the ringing sound it is necessary,
during a receiving call, to press momentarily
the button
call and the conversation.
The status (enabled or disabled) and the level
of the ringing sound are stored and they are
used for next calls. If the ringing sound is
disabled during a receiving call or during a
communication the red LED will flash to
indicate this status, but no LED indication will
be present in stand-by mode. After connecting
a positive 15÷18Vdc to the terminal V+ it will
be possible to have the LED indication of the
disabled ringing sound also with the video
intercom in stand-by mode.
Setting of the audio volume
-With the video intercom switched ON, press
the button
E
C
H
O
S
T o set the receiving audio level (loudspeaker)
press left and right the button
the selected level press the button
pressure of this button switches OFF the
video intercom.
-To set the amplifier’s level of the microphone
it is necessary to adjust the trimmer
the back of the videointercom.
-In case of incorrect automatic switching of
the video intercom between talk and listening
function decrease the level of the preferred
function and increase the other one by
acting on the button
and Contrast adjustment.
. T o store the current setting press
.
; the red LED flashes during the
to enable the communication.
or on the trimmer
of the videointercom.
to adjust the
. The pressure of
. T o store
. The
on
-If required the communication the audio is
intermittent or distorted it is advisable to
adjust the microphone sensitivity by acting
on the trimmer MIC.SENS. located on the
back of the video intercom.
-Attention. For a better setting of the audio
levels on the video intercom adjust the
microphone sensitivity of the door station to
the minimum value and the loudspeakers
volume to an intermediate value.
- If there are intercommunicating devices
adjust also their audio levels.
PROGRAMMING
In programming mode it is possible to select
the duration and the ringer tone among 5
different possibilities.
T o enter the programming mode it is required:
-to switch ON the video intercom pressing the
button
-to keep pressed for more than 2 seconds the
buttons
operation and the red LED lights up.
Number of rings of the bell (external and
intercommunicating calls)
After entering the programming mode it is
necessary:
- to press the button
of the rings currently programmed;
- to press left and right the button
respectively increase or decrease the
number of rings. After each pressure of the
button the selected number of rings will be
heard;
- please keep the button pushed for more
than 2 seconds or wait for the end of the
programming time in order to make the
changes confirmed and exit from the operation.
Ringer tone selection (call from door station)
Once entering into programming mode, it is
necessary:
- to push the
ringer tone now programmed;
- to push laterally (left or right side) the
button to select the previous or next ringer
tone;
- after having selected the favorite ringer
tone, keep the
than 2 seconds or wait for the end of the
programming time to make the changes
confirmed and exit from the operation.
.
; a beep will confirm the correct
to verify the number
to
button in order to check the
button pushed for more
OPERA TIONS
Call from the door station
Making a call from the door station the video
intercom will ring (according to the
programming) or the red LED starts flashing
if the bell rings has been disabled; on the
display appears the image of the calling
station. T o start the communication press the
button
to the door station, but continuing hearing the
audio from the door station press shortly the
button
up continuously . To restore the audio to the
door station press again the button
red LED will recover the previous status. T o
end the communication and switch OFF the
video intercom press the button
video intercom switches OFF automatically
when the communication time expires or if
from the door station a call to another user is
made.
Control switching ON
The button
from 1 to 6, if present and correctly
programmed (see table on the page 4), allow
to display the images (without audio) of the
entrances presents in the system. T o get also
the audio it is sufficient to press the button
intercom.
Control switching ON is allowed only when the
system is in stand-by mode (no running
communications); if, pressing the control
switching ON buttons, the video intercom
doesn’t switch ON a communication between
another user and the door station could be
active.
Door lock release
To operate the electric door lock release
press the button
video intercom is switched ON or OFF .
If the system has more door stations the
electric door lock release of the door station
from which the last call has been made or to
which a control switching ON has been
directed will be activated.
. If it is desired to disable the audio
; in this status the red LED will light
; the
. The
and the buttons numbered
. Press it again to switch OFF the video
independently if the
8
(MT11 - Gb2012)
INTERNAL STATIONS
EXHITO SERIES
VIDEOINTERCOMS
62
7
"
/
2
16
211
8
5
"
/
16
218
8
EX3160. White Flat videointercom with pri-
vate audio-video function, electronic microphone, differentiated double electronic ringing
sounds (modulated and continuous) and terminal board for the connection to the wall bracket.
Equipped with led's and 2 buttons for camera
control switch ON and door-open. Together
with the videointercom there are 5 extra buttons
which can be assembled in the proper slots
(see page 10).
The videointercom can be fixed to the wall
(flush-mounted) with the WB3161 bracket.
WB3161. Wall bracket for EX3100C, EX3160 and EX3160C video
intercoms with terminal boards for connection to the system and an
electronic circuit to convert the video signal from coax cable to a
balanced twisted pair.
Terminals
X Balanced negative video signal input
Y Balanced positive video signal input
F Ground
H Positive voltage input (+18-24Vdc)
10 Call, audio reception/transmission, door releasing
4 Control switching ON (button
9
"
/
16
A1 Electronic call input from other intercommunicating devices
1C Common contact for P1, P2, P3 (P2-P3 only for EX3160, EX3160C)
P1 Service button (max 0.3A)
P2 ÷ P5 (*) Service buttons (max 0.3A)
2C (*) Common contact for buttons P4 and P5
L1+ (*) Positive power supply input for red Led (+12Vdc)
L1- (*) Negative power supply input for red Led
L+ Not connected
(*) Not connected in EX3100C videointercom.
)
Wall version
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
Technical data
Power supply 12÷15Vdc
Operating current 0.4A
Monitor 4" FLAT CRT
TV standard CCIR-625 lines
Line frequency 15625Hz
Frame frequency 50Hz
Bandwidth >5MHz
Video signal on 75Ω 0.8÷1.5Vpp
Switching ON time 2 seconds
Operating temperature 0°÷+50°C
Maximum permissible humidity 90%RH
EX3160C. Version of EX3160 videointercom
with colour LCD.
EX3100C. It is dif-
ferent from the model
EX3160C because
of the lack of LED’s
and for the reduced
number of buttons
(only 3 for electrical
lock release, monitoring and supplementary functions).
Technical data
Power supply
12÷15Vdc
Operating current 0.4A
Screen 4" LCD
TV standard PAL
Line frequency 15625Hz
Frame frequency 50Hz
Bandwidth >5MHz
Video signal on 75Ω 0.8÷1.5Vpp
Switching ON time 1 second
Operating temperature 0°÷+50°C
Maximum permissible humidity 90%RH
-This area has to be free; remove possible present cables.
Fix the wall bracket by using 3 expansion plugs.
Don't shut the 3 screws of fixing if the wall is irregular.
It is suggested to use a wall box to contain the extra wires.
Plugging in of videointercom connectors to
the terminal boards of
wall bracket.
Installation of videointercom onto the wall bracket.
E
X
H
I
T
O
9
(MT11 - Gb2012)
INTERNAL STATIONS
P1
10
Y
X
F
H
A1
1C
4
Yellow
Junction box
Y
Y
X
WB3161
1+1
INTERCOMS *
Installation of videointercom onto the
wall bracket.
4+1
VIDEOINTERCOMS
Assembling of extra buttons to the
videointercom EX3160 and EX3160C
Taking out of button caps
Table version
TA3160. Table adaptor with weighted base, junction box and 2.4m connection cable
with 20 wires.
Mounting of the additional buttons
E
X
H
I
Remove the cover to the junction box and
connect wires to the terminals matching the
colour of wire with that of the label. Write in
the proper space the code of the connection.
Choosing the private conversation or intercommunicating service
1-2 =Video intercom with-
out audio privacy
2-3 =Video intercom with
audio privacy
T
O
10
(MT11 - Gb2012)
INTERNAL STATIONS
EXHITO SERIES
INTERCOMS
2
62
7
"
/
16
65
2
9
"
/
16
218
9
"
/
8
16
EX311. White electronic intercom with two
push-buttons, spiral cord, electronic microphone and possibility to insert an additional
EX301 push-button and a SR41 or SM50 mod-
ule. Wall-mountable with expansion plugs or
wall box.
Terminals
1 audio line, bell and door release control
3 ground
6 output electronic bell *
7 ground. Connected to terminal 3 with
jumper W1 *
A1 floor call or intercommunicating call input
P service push-button
C common contact for P push-button
Wall version
172.5
13
/
6
16
1+1
INTERCOMS *
172.5
13
"
/
6
16
4+1
VIDEOINTERCOMS
"
* terminals to be used when installing the pri-
vate conversation module SM50 in the inter-
com.
Accessories
EX301. Single button module for Exhito
intercoms. Maximum contact current is 0.1A.
For higher currents use a relay.
Note. For easier reference the 2 terminals of
the module are defined as C and P, but they
have no polarity and can be inverted.
EX304. Additional loudspeaker module
(*).
RL 36. Relay module (*).
SM50. Private conversation module (*).
SR41. Electronic buzzer module (*).
(*) for the connections and the characteristics
of the modules refer to page 13.
EX301
SR41 or
RL36 or
SM50 or
EX304
P
C
3
3
7
E
X
H
I
1
6
A1
T
O
11
(MT11 - Gb2012)
INTERNAL STATIONS
A161733CP
EX321
Yellow
Junction box
1
1
3
INTERCOMS
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
EX321. White colour intercom for 1+1 inter-
com systems and intercommunicating systems
connected to 1 or more external door stations.
Complete with spiral cord, electronic microphone and 2 buttons extendable to 8 by adding
the EX301 single button module.
Possibility of inserting modules EX304, EX332,
SR41, RL36 and SM50.
Wall-mountable with expansion plugs or wall
box or on the desk using the table adaptor
TA320.
Terminals
1 audio line, bell and door release control
3 ground
6 output electronic bell *
7 ground. Connected to terminal 3 with
jumper W1 *
A1 floor call or intercommunicating call input
P service push-button
C common contact for P push-button
* terminals to be used when installing the
private conversation module SM50 in the inter-
com.
83.5
1
"
/
3
4
Table version
TA320. T able adaptor with weighted base, junction box and 2.4m
connection cable with 20 wires.
Remove the cover of the junction
box and connect wires to the terminals matching the colour of wire with
that of the label. Write in the proper
space the code of the connection.
EXHITO SERIES
172,5
13
"
/
6
16
E
X
H
I
T
O
Wall version
Accessories
EX301. Single button module for Exhito in-
tercoms. Maximum contact current is 0.1A. For
higher currents use a relay.
Note. For easier reference the 2 terminals of the
module are defined as C and P, but they have no
polarity and can be inverted.
12
(MT11 - Gb2012)
INTERNAL STATIONS
EX304. Additional loudspeaker. It allows
to receive calls with off-hook handset, or in
systems with 2 calls, with 1 single call and 1 call
in common to other intercoms.
To install the module the last module holder on
the intercom base must be removed (see drawing). The article
takes the space
of 2 modules and
therefore reduces the number of additional
buttons to 4.
EX332. Module with 3 LED.
RL 36. Relay module. When installed inside
intercoms it allows to activate additional bells.
Maximum switching current is 1A (24V).
Terminals
C common terminal of relay
NA normally open contact of relay
NC normally closed contact of relay
- ground
13Vac/dc voltage input
EC relay activation input (ground command)
Wires
9 electronic call in-
put without resistive load
3 ground
9
3
EC
NA
NC
C
SR41. Electronic buzzer module. In the
intercoms can be added for having a further call
signal.
Terminals
4 power supply input
(13Vac-70mA; 9÷20Vdc-15mA)
3 ground
SM50. Private conversation module.
To have complete audio privacy between users it is necessary to add to each intercom the
private conversation module.
The intercom can communicate with the outside (for an unlimited period) only after having
received the call. The intercom becomes
disactived when there is a call from another
intercom or the door release push-button is
pressed.
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
L1, L2, L3
terminals input + / - : max 13Vac / 24Vdc
ST703. Ringing volume adjustment
switch.
C
9
P
P = audio and call conduc-
tor
= ground conductor
Note
Do not use this connection
in intercoms where is
already installed the module
SM50.
A1
6
1
3
7
EX321
Additional bell connection
If the ringing volume is not sufficient or if you
need to chime the call in a different place, you
can add an additional bell enabled by a relay.
intercom
terminals
13÷48Vac/dc
Terminals
C audio line receiver
B audio line transmitter
- ground
Note
B and C terminals are unused in an 1+1 intercom
system.
CT
C
B
R1
Notes
In each intercom EX311 or EX321 it is neces-
sary:
- to cut the jumper (W1) that links the terminals 3 and 7;
- to make the connection between terminal 7 of
the intercom and the - (minus) of the private
conversation module.
In all SM50 private conversation modules cut
the resistance R1.
EX311 + SM50
EX321 + SM50
1
6
2
3
1
6
3
7
W1
E
X
H
I
OFF MED. MAX.
3 levels to adjust ring-
ing volume (off, me-
dium and maximum)
T
O
13
(MT11 - Gb2012)
INTERNAL STATIONS
1+1
VIDEOINTERCOMS
88
7
"
/
INTERCOMS *
229
"
9
3
16
4+1
VIDEOINTERCOMS
140 150 cm÷
47"
COMPACT SERIES
201
15
"
/
7
16
11"
4
Installation
Fix the wall bracket by using 4 expansion plugs
KM8111W. White flat video intercom with
two buttons, one for control switch ON and one
for door lock release, audio-video privacy, electronic microphone, electronic modulated call
note, terminal board for the connection to the
wall-bracket. It can be installed on the wall (with
no built-in) by using the art.WB8111.
KM8111CW. Version with colour LCD.
WB8111. Wall-bracket for the KM8111W
and KM8111CW video intercoms. It includes a
terminal board for connection to the system.
Technical data
Power Supply 18÷24Vdc
Operating current 0.5A
Video tube (KM8111W) 4" FLAT CRT
Screen (KM8111CW) 4" LCD
Television standard (KM8111W) CCIR-625 lines
Television standard (KM8111CW) PAL
Horizontal frequency 15625Hz
Vertical frequency 50Hz
Bandwidth >5MHz
Video signal balanced
Starting up time (KM8111W) 2÷4 seconds
Starting up time (KM8111CW) 1 second
Operating temperature 0°÷+50°C
Max. permissible humidity 90%RH
C
Terminals
H Positive power supply input 18÷24Vdc-0.5A
F Ground
O
X and Y Video signal input
10 Call, audio reception/transmission, door re-
M
P
leasing
4 Control switch ON - button
A1 Floor call input
PC - P Service push-buttons
A
C
(max 0.3A)
Plugging in of videointercom connectors to the terminal boards of wall
bracket.
Dismounting of videointercom from the wall bracket.
Choosing the private conversation
A
X
Y
3
A1
2
1
J1
F
F
H
10
4
P
PC
123
123
J1
1-2 = Videointercom with-
B
J1
2-3 = Videointercom with
Installation of videointercom onto the wall
bracket.
out audio privacy
audio privacy
T
14
(MT11 - Gb2012)
INTERNAL STATIONS
3
"
16
/
1
2
8
"
"
16
16
/
/
13
1
77.572
214
COMPACT SERIES
PROJECT SERIES
INTERCOMS
2
65
9
"
/
16
3
86
3
"
/
8
211
5
"
/
8
16
KM811W. White electronic intercom with 1
push-button, spiral cord, electronic microphone
and possibility to insert an additional ST701
push-button and a SR41 or SM50 module
(description and characteristics of the modules on page 13). Wall-mountable with expan-
sion plugs or wall box.
Terminals
1 audio line, bell and door release control
3 ground
6 output electronic bell *
7 ground. Connected to terminal 3 with jumper
W1 *
A1 floor call input
INTERCOMS
PT511EW. White electronic intercom with 1
push-button, spiral cord, electronic microphone
and possibility to insert SR41 or SM50 module
(description and characteristics of the modules on page 13). Wall-mountable with expan-
sion plugs or wall box.
Terminals
1 audio line, bell and door release control
3 ground
6 output electronic bell *
7 ground. Connected to terminal 3 with jumper
W1 *
A1 floor call input
* terminals to be used when installing the private
conversation module SM50 in the intercom.
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
* terminals to be used when installing the private
conversation module SM50 in the intercom.
Mounting of the additional button ST701.
ST701
182
7
3
"
/
16
83
1
"
/
3
4
K
M
P
T
15
(MT11 - Gb2012)
EXTERNAL DOOR ST ATIONS
External door station
1+1 INTERCOMS * 4+1 VIDEOINTERCOMS
30
1
3
/
16
"
208
8
99
"
7
8
/
3
3
"
/
16
AG100A. Audio Door Station composed of an
ABS box for surface mounting, front plate in aluminium and electronic board with diodes and LED’s
for lighting the nameplates. Suitable for the AG30ED
door speaker and maximum 4 AG21 single pushbuttons or 4 AG222 double push-buttons.
AGL100A. Light grey version.
Surface mounting Door Stations
with reduced width and thickness.
Installation is easy and quick
because no recessed box is
required. Front plate is in extruded
anodized aluminium. Name plates
are backlighted with blue LED’s
for a better reading even in dark
places. Reduced dimensions and
surface mounting features make
the product particularly suitable
for the installations on the entry
gate’s post.
x 1
x 4
x 1
AGORA' SERIES
AG20. Blank module
AGL20. Light grey version.
AG21. Single button module with name plate
holder.
AGL21. Light grey version.
AG222. Double button unit with name plate
holder.
AGL222. Light grey version.
AG30ED. Audio Door Speaker to fit inside
the Door Stations AG100A and AGL100A.
Terminals
A Alternated power supply input for audio and
name-plate Led (13Vac-0.1A)
- Ground
1 Reception-transmission / door releasing / call
S Electric lock
A
G
O
R
À
AG100V. Video Door Station composed of an
ABS box for surface mounting, front plate in aluminium and electronic board with diodes and LED’s
for lighting the nameplates. Suitable for AG40CED
colour camera with door speaker and maximum 2
AG21 single push-button or 2 AG222 double push-
buttons.
AGL100V. Light grey version.
x 1
x 2
x 1
AG100T. Push-buttons Door Station com-
posed of an ABS box for surface mounting, front
plate in aluminium and electronic board with diodes
and LED’s for lighting the nameplates. Suitable for
8 AG21 single push-button or 8 AG222 double
Push-buttons.
AGL100T. Light grey version.
x 2
x 8
AG40CED. Colour camera with integrated door speaker to fit
inside the Door Stations AG100V and AGL100V.
Technical data
Video power supply 18÷24VDC-0.21A
Audio power supply 13VAC-0,15A
Video signal output balanced
Video signal standard PAL
Minimum lighting 2.5 Lux
LED's 4 white
Sensor CCD 1/3"
Number of pixel 291,000
Lens 3.6mm
Focusing 0.6m ÷ ∞
Horizontal/vertical sweep ±10°
Operating temperature -10° ÷ +40°C
Maximum permitted humidity 80% RH
Terminals
H Positive voltage input for camera (18÷24Vdc)
F Ground
X Balanced negative video signal output
Y Balanced positive video signal output
A Alternated power supply input for audio and name-plate Led (13Vac)
- Ground
1 Reception-transmission / door releasing / call
S Electric lock
16
(MT11 - Gb2012)
EXTERNAL DOOR STA TIONS
Installation and Assembly of AGORA’ door stations.
1
2a
AG100V
AGL100V
AG40...
2b
AG100A
AGL100A
AG30...
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
3a 3b
AG100V
AGL100V
max.2
AG100A
AGL100A
max.4
3c
AG100T
AGL100T
max.8
A
G
O
R
17
(MT11 - Gb2012)
À
AS1
Anti-feedback (Larsen
effect) adjustment
Receiver adjustable
volume (loudspeaker)
Transmitter adjustable
volume (microphone)
EXTERNAL DOOR ST ATIONS
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
4a
The wires of connection
cable must be connected
to the calling terminal (not
to the common terminal)
5a
4b
.
Cut and keep insulated not
used wire.
5b
Adjustments AG30ED and AG40CED
Adjustments are carried out in the factory; should any be
necessary they can be re-adjusted from the outside with a
screwdriver with the trimmers identified by the symbols
"
" and .
Adjustment of volume
Rotate trimmer
ing channel (loudspeaker).
Rotate trimmer
transmitting channel (microphone).
Anti-feedback adjustment
A
- Make a call from the door station and pick up the handset
G
O
R
À
of one of the videointercoms.
- Remove the microphone from its housing inside the
push-button panel, place it on the loudspeaker of the
electric door answering system and adjust the
trimmer until the feedback stops (Larsen effect).
- Replace the microphone in its housing.
Sweeps
If necessary, you can manually change the camera framing
by adjusting the horizontal and vertical levers in the desired direction (see figure).
to change the volume of the receiv-
to change the amplification of
±10°
±10°
HXASFY1
18
(MT11 - Gb2012)
Anti-feedback (Larsen
effect) adjustment
Transmitter adjustable
volume (microphone)
Receiver adjustable
volume (loudspeaker)
AG40CED
"E" terminal.
Cut the red wire to get "E"
terminal only if required by
the installation diagram.
AG30ED
EXTERNAL DOOR STA TIONS
ASSEMBLY MODULE SEQUENCE
Insert the Push-buttons or blank modules starting
from the top of the frontal plate
6
AG21
AG222
AG100T
AGL100T
7b
AG20
AG21
AG222
AG100T
AGL100T
7a 8a
AG100V
AGL100V
AG100A
AGL100A
AG20
AG21
AG222
AG100T
AGL100T
8b
AG100V
AGL100V
AG100A
AGL100A
9b
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
10
11
12
A
G
O
R
À
19
(MT11 - Gb2012)
EXTERNAL DOOR STA TIONS
1+1
ASSEMBLING DOOR STA TIONS SIDE BY SIDE
INTERCOMS *
AG100V
AGL100V
AG100A
AGL100A
AG100T
AGL100T
4+1
VIDEOINTERCOMS
Remove the side plastic caps
(only from the interested side)
to insert the spacers.
AG100V
AG100T
AGL100T
AGL100V
AG100A
AGL100A
A
G
O
R
À
AG100T
AGL100T
AG100V
AGL100V
AG100A
AGL100A
20
(MT11 - Gb2012)
EXTERNAL DOOR STA TIONS
Composition of door stations and requested quantities of modules
1 ROW VIDEOINTERCOM push-button panels 2 ROW VIDEOINTERCOM push-button panels
AG100V AG100T AG20
N. buttons
AG40CED
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
-
-
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
AG21
1
1
2
-
3
7
4
6
5
5
6
4
7
3
8
2
9
1
10
-
11
7
12
6
13
5
14
4
15
3
16
2
17
1
18
-
19
7
20
6
21
5
22
4
23
3
24
2
25
1
26
-
27
7
28
6
29
5
30
4
31
3
32
2
33
1
34
-
N. buttons
AG100V AG100T AG20
AG40CED
2
1
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
4
1
4
1
4
1
4
1
4
1
4
1
4
1
4
AG222
1
-
-
-
7
6
5
4
3
2
1
10
-
11
7
12
6
13
5
14
4
15
3
16
2
17
1
18
-
19
7
20
6
21
5
22
4
23
3
24
2
25
1
26
-
27
7
28
6
29
5
30
4
31
3
32
2
33
1
34
-
1+1
INTERCOMS *
1
2
3
4
5
6
7
8
9
4+1
VIDEOINTERCOMS
1 ROW INTERCOM push-button panels 2 ROW INTERCOM push-button panels
AG100A AG100T AG20
N. buttons
AG30ED
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
-
-
-
-
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
AG21
1
3
2
2
3
1
4
-
5
7
6
6
7
5
8
4
9
3
10
2
11
1
12
-
13
7
14
6
15
5
16
4
17
3
18
2
19
1
20
-
21
7
22
6
23
5
24
4
25
3
26
2
27
1
28
-
29
7
30
6
31
5
32
4
33
3
34
2
35
1
36
-
N. buttons
AG100A AG100T AG20
AG30ED
2
1
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
4
1
4
1
4
1
4
1
4
1
4
1
4
1
4
-
-
-
-
AG222
1
3
2
2
3
1
4
-
5
7
6
6
7
5
8
4
9
3
10
2
11
1
12
-
13
7
14
6
15
5
16
4
17
3
18
2
19
1
20
-
21
7
22
6
23
5
24
4
25
3
26
2
27
1
28
-
29
7
30
6
31
5
32
4
33
3
34
2
35
1
36
-
A
G
O
R
À
21
(MT11 - Gb2012)
EXTERNAL DOOR STA TIONS
1+1
Push-button panels in extruded aluminium and
steel push-buttons made up of modular ele-
INTERCOMS *
ments. Suitable for the most diverse installation requirements. The careful selection of
modules allows for multiple application opportunities; from one-way installations to blocks of
flats; from intercom to video intercom installations.
The optimized size of modules allows for easy
installation on the gage jamb.
4+1
VIDEOINTERCOMS
Hood covers
PROFILO SERIES
Module frames complete with back box
PL 71 PL 72 PL 73
PL 81 PL 83PL 82 PL 84 PL 86 PL 89
Rain shelters with module frames
P
R
O
F
I
PL 91 PL 93PL 92 PL 94 PL 96 PL 99
L
O
22
(MT11 - Gb2012)
EXTERNAL DOOR STA TIONS
PROFILO push-button panel
Modules with integrated door speaker
PL10PED
without call buttons
PL 50
number module
PL11PED
with 1 call button
PL 20
blank module
PL12PED
with 2 call buttons
Push-button modules
Video modules with integrated door speaker
PL40PED
without call buttons and
with B\W camera
PL40PCED
colour version
For specifications see page 24.
PL41PED
with 1 call button and B\W
camera
PL41PCED
colour version
PL42PED
with 2 call buttons and
B\W camera
PL42PCED
colour version
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
PL 21
with 1 call button
Access control modules
FC 52PL
Keypad module
for access control
(see characteristics on page 25).
Technical characteristics and terminal boards of the audio-video modules
PL10PED PL11PED PL12PED PL40PED PL41PED PL42PED
1111 1 1
EEEE E E
SSSS S S
AAAA A A
---- - CC C C
P1 P1 P1 P1
L+ L+ L+ L+ L+ L+
PL 22
with 2 call buttons
FP 52PL
Proximity reader for
access control (see
characteristics on
page 25).
PL40PCED PL41PCED PL42PCED
P2 P2
XXX
YYY
HHH
FFF
PL 23
with 3 call buttons
Technical characteristics and terminal boards of the button modules
PL21 PL22 PL23 PL24 PL226 PL228 PL50
AAAAAAA
(25mA) (50mA) (0.1A)
------C C C C C/C2 C/C2
P1 P1 P1 P1 P1 P1
PL 24
with 4 call buttons
P2 P2 P2 P2 P2
P3 P3 P3 P3
P4 P4
Reception-transmission; electric lock release; call
Reception-transmission; electric lock release
Electric lock
DC power supply input for door speaker and name-plate Led (13Vac-70mA)
Ground
Call push-buttons common
Call push-button
Call push-button
Negative video signal output
Positive video signal output
Positive voltage input for camera (18÷24Vdc)
Video ground
DC power supply input for service Led (12Vdc)
P5÷P7 P5÷P7
P8
PL226
with 6 call buttons (2 row)
AC power supply input for nameplate
Led (13Vac)
Ground
Call push-buttons common
Call push-button
Call push-button
Call push-button
Call push-button
Call push-buttons (C2 common)
Call push-button (C2 common)
PL228
with 8 call buttons (2 row)
P
R
O
F
I
L
O
23
(MT11 - Gb2012)
EXTERNAL DOOR ST ATIONS
1+1
Video modules with integrated door speaker
INTERCOMS *
Testing and adjustments
Adjustments are carried out in the factory; should
any be necessary they can be readjusted from
the outside with a screwdriver with the trimmers
identified by the symbols "
Volumes adjustment
To adjust the volume of microphone and loudspeaker, turn the trimmers
" and .
and .
4+1
PL40PED. Modules complete with:
- CCD color camera with autoiris and fixed
3.6mm lens.
VIDEOINTERCOMS
- amplified speaker unit with volume
adjustment of 2 channels (reception and
transmission)
- aluminium front plate with transparent
screen
- horizontal and vertical adjustments
- red operation LED
PL40PCED.
Colour version of the PL40PED model.
PL41PED.
Same as PL40PED, with 1 call button and
name plate panel with transparent screen
and green LED backlighting.
PL41PCED.
Colour version of the PL41PED model.
PL42PED.
Same as PL40PED, with 2 call buttons
and name plate panel with transparent
screen and green LED backlighting.
PL42PCED.
Colour version of the PL42PED model.
241DMA. Module with diodes for 4 users.
It allows for the use of the button modules PL21,
PL22, PL23, PL24, PL226 and PL228 in the 1+1
intercom systems and 4+1 video intercom systems. It is fixed on the back of the button modules
using the 2 supplied screws. Connect the conductors of the diode module to the corresponding
terminal on button module; if modules with a reduced number of Push-buttons are used (PL21,
PL22, PL23, PL226) do not connect and insulate
the excess of wires.
Cut a portion of the metal terminals to connect the
conductors to the terminal board of push buttons
modules.
Antilocale adjustment
In case of "feedback" (Larsen effect) in the
external unit it is necessary to operate as follow:
- make the call from the door station and lift the
handset of an intercom or videointercom
(press
- adjust the trimmer
(Larsen effect).
Receiver
adjustable volume
Receiver
adjustable volume
for Echos series);
until the whistling stops
Transmitter
PL40P...
S
FHX
L+
Y
Transmitter
volumeadjustable
Anti-feedback
(Larsen effect)
adjustment
volumeadjustable
PL21
PL22
Technical data PL40PED-PL41PED- PL40PCED-PL41PCED-
Camera power supply 18÷24Vdc-0.3A 18÷24Vdc-0.4A
Audio power supply 13Vac-0.07A 13Vac-0.07A
Video signal output balanced balanced
Video signal standard CCIR PAL
Minimum illumination 2 Lux 2.5 Lux
White balanced - auto
P
Led's 6 infrared 6 white
Sensor CCD 1/4" B/W CCD 1/3" colour
R
Number of pixels 291,000 291,000
Horizontal frequency 15,625Hz 15,625Hz
O
Vertical frequency 50Hz 50Hz
Lens 3.6mm 3.6mm
Focus 0.1m ÷ ∞ 0.6m ÷ ∞
F
Autoiris electronic electronic
Horizontal adjustment ± 15° ± 15°
I
Vertical adjustment ± 15° ± 15°
Operating temperature -10°÷+40°C -10°÷+40°C
L
Maximum permissible humidity 80%RH 80%RH
PL42PED PL42PCED
PL23
PL24
PL226
PL228
O
PL10P...
S
L+
Anti-feedback
(Larsen effect)
adjustment
Adjustments
You can manually change the camera framing
by unloosening and adjusting the horizontal
and vertical screws in the desired direction.
±15°
24
(MT11 - Gb2012)
EXTERNAL DOOR STA TIONS
PROXIMITY READER FOR ACCESS
CONTROL
FP52PL.
This article allows for the activation of 2 relays
by means of keytags or electronic ISO cards
based on transponder technology.
Programmable activation time from 1 to 63
seconds for every relay. 4 user cards and 1
master card supplied with the product. Acoustic
and visual control signals and 3-digit display to
view numbers and codes during set-up and
operation.
Technical data
Power supply 12Vac/dc ±10%
Stand-by current 0.1A
Maximum current consumption 0.25A
Contact ratings 24Vac - 2A
Max. number of cards 490
Max. number of Master cards 10
Number of relays 2
Relay time 1 to 63 sec.
Minimum recognition distance 3 cm
Maximum recognition time 1 sec.
Operating temperature 0° ÷ +40°C
Maximum permitted humidity 85% RH
Terminals
+/A positive or alternate current input
-/A ground or alternate current input
PB door open button
NC2 normally closed contact of relay 2
NA2 normally open contact of relay 2
C2 common terminal of relay 2
NC1 normally closed contact of relay 1
NA1 normally open contact of relay 1
C1 common terminal of relay 1
ACCESS CONTROL KEYPAD
FC 52PL.
Access control keypad with 12 digits and 2
relays for lock release. 4 programmable access codes for each relay. Programmable door
opening time from 1 up 99 sec. for each relay
(or bistable operation of relay 1). Acoustic and
visual confirmation for entered keys, accepted
programming and for wrong codes.
Technical data
Power supply: 12Vac/dc ±10%
Stand-by current: 0.06A
Maximum current consumption: 0.15A
Contact ratings: 12Vac-2A
Numbers of codes for relays 1: 12 or direct
activation
Numbers of codes for relays 2: 12 or direct
activation
Activation time for each relay: from 1 to 99 sec.
(or bistable relay 1)
Operating temperature: 0° ÷ +40°C
Maximum permissible humidity: 85% RH
Terminals
NC2 normally closed contact of relay 2
NA2 normally open contact of relay 2
C2 common contact of relay 2
NC1 normally closed contact of relay 1
NA1 normally open contact of relay 1
C1 common contact of relay 1
ground or alternate voltage input
positive or alternate voltage input
P2 activation of the relay 2; if momentarily
connected to ground it allows the activation for the programmed time
P1 activation of the relay 1; if momentarily
connected to ground it allows the activation for the programmed time
INSTALLATION
PL42PED
PL24
Place the push-button panel back box at a
height of about 1.65m (5' 5") from the floor
keeping the front edges flush-mounted and vertical to the finished plaster.
Position the camera in such a way that
sunlight or other direct or reflected light
sources with high intensity do not hit the
camera lens.
PL12PED
PL24
"
5
5
Assembling modules side by side
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
Card recognition LED. It turns ON during card recognition.
Relay activation LED. It indicates relay
deactivation (red) or activation (green).
Program LED. It turns ON during system
programming.
Card cancellation and system setup
LED. It turns ON during Master or user
card cancellation and system setup.
25
(MT11 - Gb2012)
Insertion of spacers between back boxes.
Spacers and cable bushing (not supplied with
the products) must be inserted before brick
work.
P
R
O
F
I
L
O
EXTERNAL DOOR ST ATIONS
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
Openings for cables.
Fix lower part of the
frame to the back box
and make the electrical connections.
Rain shelter
Fix lower part of the
frame to the rain shelter
and make the electrical
connections.
P
R
O
F
I
L
Flush mounting and cables placing.
Mounting of
module.
Fixing of module frames to the upper side by the
2 small screws included in the back boxes.
Fixing of frame to back box.
Align the frame before tightening the screws.
Fixing of module frames to the upper side by
the 2 small screws included in the rain shelter.
Fixing of frame to rain shelter.
Align the frame before tightening the screws.
O
26
(MT11 - Gb2012)
EXTERNAL DOOR STA TIONS
1 row push button
1 ROW PUSH BUTTON PANELS
1 call button
2 call
buttons
22 call buttons
4 call
buttons
6 call
buttons
25 call buttons 28 call buttons 30 call buttons
buttons
8 call
10 call
buttons
Examples of compositions in intercom systems
11 call buttons 14 call buttons
17 call buttons
20 call buttons
31 call buttons
1+1
INTERCOMS *
4+1
VIDEOINTERCOMS
34 call buttons
N°
Dimensions
calls
1
2
4
6
8
10
11
14
100x142x19
15
/16" x 5 9/16" x 3/4")
(3
100x253,5x19
15
/16" x 10" x 3/4")
(3
100x365x19
15
(3
/16" x 14 3/8" x 3/4")
200x253,5x19
7
/8" x 10" x 3/4")
(7
17
20
200x365x19
7
(7
/8" x 14 3/8" x 3/4")
22
25
28
400x253,5x19
3
/4" x 10" x 3/4")
(15
30
31
34
300x365x19
13
/16" x 14 3/8" x 3/4")
(11
38
40
42
400x365x19
3
/4" x 14 3/8" x 3/4")
(15
46
(**) If requested the hood covers can be added (see
on page 22)
Door speaker
module (ampl.)
1 PL11PED
1 PL12PED
1 PL10PED
1 PL12PED
1 PL10PED
1 PL12PED
1 PL11PED
1 PL12PED
1 PL11PED
1 PL12PED
1 PL12PED
1 PL11PED
1 PL10PED
1 PL12PED
1 PL11PED
1 PL12PED
1 PL12PED
1 PL10PED
1 PL12PED
1 PL12PED
40 call buttons
42 call buttons
46 call buttons38 call buttons
Composition board of Profilo push-button panels.
Button, blank or informa-
tion modules
-
1 PL24
1 PL24
2 PL24
2 PL24
2 PL24
3 PL24
4 PL24
4 PL24
5 PL24
6 PL24
7 PL24
7 PL24
7 PL24
8 PL24
9 PL24
10 PL24
10 PL24
11 PL24
-
-
-
-
-
-
1 PL22
-
(*)
1 PL20
1 PL22
-
(*)
1 PL20
-
-
1 PL22
-
(*)
2 PL20
1 PL20 (*)
1 PL20 (*)
-
(*) or PL50
4 diode
module
-
1 241DMA
1 241DMA
2 241DMA
2 241DMA
3 241DMA
3 241DMA
4 241DMA
5 241DMA
5 241DMA
6 241DMA
7 241DMA
7 241DMA
8 241DMA
8 241DMA
9 241DMA
10 241DMA
10 241DMA
11 241DMA
Back box and
module frame
(**)
1 PL71
1 PL71 (**)
1 PL72 (**)
1 PL72 (**)
1 PL73 (**)
1 PL73 (**)
2 PL72 (**)
2 PL72 (**)
2 PL73 (**)
2 PL73 (**)
2 PL73 (**)
4 PL72
4 PL72
4 PL72
(**)
3 PL73
3 PL73 (**)
4 PL73
4 PL73
4 PL73
4 PL73
Rain
shelters
1 PL91
1 PL91
1 PL92
1 PL92
1 PL93
1 PL93
1 PL94
1 PL94
1 PL96
1 PL96
1 PL96
-
-
1 PL99
1 PL99
-
-
-
-
It replaces
PL71, PL72 or PL73
P
R
O
F
I
L
O
27
(MT11 - Gb2012)
EXTERNAL DOOR STA TIONS
2 ROW PUSH BUTTON PANELS
1+1
INTERCOMS *
2 row push button
Examples of compositions in intercom systems
6 call
4+1
buttons
8 call
buttons
14 call
buttons
VIDEOINTERCOMS
48 call buttons 52 call buttons 56 call buttons
72 call buttons
N°
Dimensions
calls
6
8
14
16
20
24
100x253,5x19
15
/16" x 10" x 3/4")
(3
100x365x19
15
/16" x 14 3/8" x 3/4")
(3
200x253,5x19
7
/8" x 10" x 3/4")
(7
32
200x365x19
36
7
(7
/8" x 14 3/8" x 3/4")
40
P
48
52
56
400x253,5x19
3
(15
/4" x 10" x 3/4")
60
R
62
300x365x19
13
/16" x 14 3/8" x 3/4")
(11
64
O
F
I
72
78
80
82
400x365x19
3
(15
/4" x 14 3/8" x 3/4")
88
L
(**) If requested the hood covers can be added (see on
page 22)
O
16 call
buttons
Door speaker
module (ampl.)
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
1 PL10PED
20 call buttons 24 call buttons 40 call buttons
60 call buttons
80 call buttons
82 call buttons
36 call buttons32 call buttons
64 call buttons
88 call buttons78 call buttons
Composition board of Profilo push-button panels.
Button, blank or information
modules
1 PL226
1 PL228
1 PL228
2 PL228
1 PL228
3 PL228
4 PL228
3 PL228
5 PL228
6 PL228
5 PL228
7 PL228
6 PL228
7 PL228
8 PL228
9 PL228
9 PL228
10 PL228
8 PL228
11 PL228
-
-
1 PL226
-
2 PL226
-
1 PL20
2 PL226
-
1 PL20
2 PL226
2 PL226
1 PL226
-
2 PL20
1 PL226
1 PL20
3 PL226
-
(*)
(*)
(*)
1 PL20 (*)
(*)
(*) or PL50
4 diode
module
2 241DMA
2 241DMA
4 241DMA
4 241DMA
6 241DMA
6 241DMA
8 241DMA
10 241DMA
10 241DMA
12 241DMA
14 241DMA
14 241DMA
16 241DMA
16 241DMA
16 241DMA
18 241DMA
20 241DMA
20 241DMA
22 241DMA
22 241DMA
Back box and
module frame
(**)
1 PL72
1 PL72 (**)
1 PL73 (**)
1 PL73 (**)
2 PL72 (**)
2 PL72 (**)
2 PL73 (**)
2 PL73 (**)
2 PL73 (**)
4 PL72
4 PL72
4 PL72
(**)
3 PL73
3 PL73 (**)
3 PL73 (**)
4 PL73
4 PL73
4 PL73
4 PL73
4 PL73
Rain
shelters
1 PL92
1 PL92
1 PL93
1 PL93
1 PL94
1 PL94
1 PL96
1 PL96
1 PL96
-
-
1 PL99
1 PL99
1 PL99
-
-
-
-
-
It replaces
PL72 or PL73
28
(MT11 - Gb2012)
Loading...