Epson Stylus Pro 7600, Stylus Pro 9600 Product Information Guide

Page 1
EPSON Stylus Pro 7600 and 9600
-
roll paper cover
paper set lever

Printer Specifications

ink cartridge compartment
paper guides
The stand is optional for the Stylus Pro 7600.
Note:
paper set lever
optional interface shield plate
control panel
front cover

Printing

Printing method 7 color EPSON UltraChrome ink or
6 color EPSON Photographic Dye ink
UltraChrome model switchable between three ink modes:
Photo Black Mode (uses Photo Black
and Light Black cartridges)
Matte Black Mode (uses Matte Black and
Light Black cartridges)
Dual Matte Black Mode (uses two Matte
Black cartridges)
Nozzle configuration
Resolution Maximum 2880 dpi × 1440 dpi
Print direction Bidirectional
Control code ESC/P
Line spacing 1/6 inch (default), programmable in
96 nozzles for each color: black 1, black 2, cyan, magenta, yellow, light cyan, light magenta
®
Raster Photographic Driver
1/1440-inch increments
parallel interface connector
USB interface connector
AC inlet
Paper feed speed 200 ± 10 milliseconds per 1/6-inch line
RAM 32MB (Stylus Pro 7600)
64MB (Stylus Pro 9600)

Engine Reliability

Total print volume
Print head life 28 billion dots per nozzle
Periodic maintenance
Cutter blade life Approximately 2000 B0+ sheets (EPSON
20,000 B0 images, 360 × 360 dpi
Pump unit, head cleaner, and cap assembly require replacement approximately every 2 years based on 25% duty cycle
media up to 4.33 mil thick); approximately 1000 B0+ film sheets
7/02 EPSON Stylus Pro 7600 and 9600 - 2
Page 2
EPSON Stylus Pro 7600 and 9600

Electrical

Specification 120V Model 220240V Model
Input voltage range 90 to 132V 198 to 264V
Rated frequency range 50 to 60 Hz
Input frequency range 49 to 61 Hz
Rated current 1.0A 0.5A
Power consumption Stylus Pro 7600: Approx. 50 W (ISO 10561
Letter Pattern)
Stylus Pro 9600: Approx. 55 W (ISO 10561 Letter Pattern)
Both printers: 12 W or less in sleep mode

Mechanical

Paper feed Friction feed (roll and cut sheet)
Paper path Roll paper or cut sheets with manual
insertion
Dimensions Stylus Pro 7600:
Width: 43.3 inches (1100 mm) Depth: 22.5 inches (572 mm) Height: 22.0 inches (560 mm)
Stylus Pro 9600:
Width: 63.9 inches (1624 mm) Depth: 28.2 inches (717 mm) Height: 46.5 inches (1181 mm), including stand
Weight Stylus Pro 7600: 96 lb (43.5 kg) without
ink cartridges or stand
Stylus Pro 9600: 185 lb (84 kg) without ink cartridges or stand

Paper

The allowable paper dimensions are shown below:
Roll paper Cut sheets
Size (Stylus Pro 9600)
Size (Stylus Pro 7600)
Maximum external roll diameter
Thickness 3.15 to 19.7 mil (0.8 to
Notes:
Poor quality paper may reduce print quality and cause paper jams
and other problems. If you encounter problems, switch to a higher grade of paper.
Do not use curled, folded, or deckle-edge paper.
Depending on the media, best feed and print quality are
guaranteed on EPSON paper with thicknesses of 3.15 to 4.33 mil (0.08 to 0.11 mm), 64 to 90 gsm.
For best results, use paper under the following conditions:
Temperature: 59 to 77 °F (15 to 25 °C) Humidity: 40 to 60% RH
BorderFree™ (marginless) printing is available in the following paper widths:
8 to 8.5 inches 20 inches
10 inches 24 inches
12 inches 36 inches (Stylus Pro 9600
8.3 to 44.0 in. wide (210 to 1118 mm)
8.3 to 24.0 in. wide (210 to 610 mm)
2 in. core: 4 in. (103 mm) 3 in. core: 6 in. (150 mm)
0.5 mm)
only)
8.5 × 11 in. up to 44 in. wide
8.5 × 11 in. up to 24 in. wide
3.15 to 59 mil (0.8 to
1.5 mm)

Environmental

Temperature Operation: 50 to 95 °F (10 to 35 °C)
Storage:
Transit
Humidity (without condensation)
Operation: 20 to 80% RH Storage: 20 to 85% RH Transit 5 to 85% RH (stored in
3 - EPSON Stylus Pro 7600 and 9600 7/02
4 to 104 °F (–20 to 40 °C)
1 month at 104 °F (40 °C)
4 to 140 °F (–20 to 60 °C), stored in shipping container 120 hours at 140 °F (60 °C)
shipping container)
14 inches 44 inches (Stylus Pro 9600
only)
16 inches
When printing BorderFree, set the image size in your application to be approximately 3 mm (1/8 inch) larger than the intended size of your printed image.

Safety Approvals

Safety standards UL 1950, CSA C22.2 No. 950 FDA
EMC FCC part 15 subpart B, class B,
CSA C108.8 class B
Page 3
EPSON Stylus Pro 7600 and 9600

Ink Cartridges

Lightfastness* Photographic Dye:
Color: up to 26 years (using EPSON ColorLife paper); black and white not rated
UltraChrome:
Color: up to 100 years Black and white: over 100 years
Print yield Approximately 28 pages/A1
(720 dpi, 40% duty)
Approximately 3,800 pages/A4 (360 dpi, 5% duty)
Print yield may vary, depending on how often you run cleaning cycles and how much you use the printer; yield of the initial cartridge set is reduced because of ink charging.
Cartridge life: Photographic Dye
2 years from production date
UltraChrome
2 years from production date if unopened; within 6 months after opening package, at 77 °F (25 °C)
Temperature: Storage (uninstalled):
22 to 104 °F (–30 to 40 °C); 1 month at 104
°F (40 °C)
Storage (installed):
4 to 104 °F (–20 to 40 °C); 1 month at 104
°F (40 °C)
Transit
:
22 to 140 °F (–30 to 60 °C); 1 month at 104
°F (40 °C), 120 hours at 140 °F (60 °C)
Freezing:
14 °F (
10 °C); ink thaws and is usable after
at least 3 hours at 77 °F (25 °C)

Drivers

Macintosh® System 8.5.1 through 9.x (OS X clients supported via RIP, available from the EPSON web site for download), Windows
®
95, Windows 98, Windows 2000, Windows Me, Windows XP, and Windows NT 4.0. Raster drivers are standard. For Adobe optional EFI
®
Fiery® Spark Professional 2.0 Software RIP or a
®
PostScript® support, use the
third-party software solution.

Interfaces

USB (1.1 and 2.0 compatible), recommended length less
than 6 feet (2 meters)
Parallel (IEEE-1284 ECP mode)
In addition, a Type B expansion slot is available for installing one of these options:
Ethernet network card (10/1000 Base T)
IEEE 1394 (FireWire) card
The following connections are supported for each operating system:
Connection
Parallel X X X XXX
USB X* XXXX
Ethernet (optional)
FireWire (optional)
* Supported on pre-installed operating systems, not upgraded from
earlier versions of Windows.
Win 95Win 98Win
NT 4.0
X X X XXXX
In addition, Macintosh OS X supports USB and Ethenet when running applications in Classic mode.
Win
Win MeWin
2000
XXXX
XP Mac
Capacity 110 ml (all models)
220 ml (Stylus Pro 9600, UltraChrome only)
* Preliminary data from Wilhelm Imaging Research, Inc. indicate the
lightfastness of color UltraChrome prints made by the EPSON Stylus Pro 7600 and 9600 printers will be rated up to 100 years under glass on specific EPSON media. Data indicate the lightfastness of black and white UltraChrome images printed using the 7-color mode will be rated as greater than 100 years under glass on specific EPSON media.
Ink lightfastness ratings are based on accelerated testing of prints on specialty media, displayed indoors, under glass. Actual print stability will vary according to media, printed image, display conditions, light intensity, humidity, and atmospheric conditions. EPSON does not guarantee longevity of prints. For maximum print life, display all prints under glass or lamination or properly store them. Visit www.wilhelm­research.com for the latest information.
7/02 EPSON Stylus Pro 7600 and 9600 - 4
Page 4
EPSON Stylus Pro 7600 and 9600

Consumables and Accessories

Ink Cartridges

When you install the printers first ink cartridges, it takes about 10 minutes to initialize the printer. Do not interrrupt this process by turning off the printer, opening the printer covers, or releasing the paper set lever, or the printer will have to re-initialize. In that case, there may not be enough ink left in the original cartridges and you may have to replace them with new ones.
When you installed the ink cartridges that came with the printer, it was initialized as either a Photographic Dye ink model or UltraChrome ink model. If you dont use the correct replacement cartridges for your model, you will see an error message and your printer wont work until you insert the correct cartridges.
If you have a Stylus Pro 9600 that uses UltraChrome ink, you can install any combination of 110 and 220 ml cartridges. Unless youre planning to switch between black ink modes (see page 12), be sure to replace the black ink cartridges with the same type as youre currently using.
Use the following cartridges before the expiration date on the package:
Photographic Dye ink users:
Black* T545100 Light cyan T545600
Cyan T545200 Light magenta T545500
Magenta T545300 Yellow T545400
* Your printer requires two black ink cartridges.
UltraChrome ink users:
Cartridge 110 ml 220 ml*
Photo Black** T543100 T544100
Matte Black** T543800 T544800
Light Black** T543700 T544700
Cyan T543200 T544200
Magenta T543300 T544300
Light Magenta T543600 T544600
Light Cyan T543500 T544500
Yellow T543400 T544400
* Stylus Pro 9600 only.
** Your printer uses two black ink cartridges. Unless you are switching
between black ink modes, use the same type of cartridges as are currently installed. Check their type by looking at the installed cartridges. If you install an incorrect cartridge, you will see the message
WRONG INK CARTRIDGE
.

User-Replaceable Parts

You can order these user-replaceable parts:
Part Part number
Relacement Ink Maintenance Tank C120890071
Replacement Printer Cutter Blade (replaces the printers built-in cutter)
C12C815241

Options

The following options are available:
Part Part number
EPSON Stylus Pro 7600 Printer Stand C12C844061
®
Fiery® Spark Professional 2.0 Software RIP C842832
EFI
Internal 10/100 BaseT (Ethernet card
Internal IEEE 1394 (FireWire
Automatic Take-Up Reel System (Stylus Pro 9600 only) C12C815251
Replacement 44-inch Take-up Reel Core (Stylus Pro 9600 only)
Paper Roller Spindle (Normal Tension) 2- or 3-inch
Paper Roller Spindle (High Tension) 2- or 3-inch
Manual Media Cutting System*
Replacement Manual Cutting Blade (for Manual Media Cutting System)
* Designed for use with heavy media, which may damage the printer’s
built-in cutter.
) Type-B interface
) Type-B interface card C823722
Stylus Pro 7600: Stylus Pro 9600:
Stylus Pro 7600: Stylus Pro 9600:
Stylus Pro 7600: Stylus Pro 9600:
C12C823912
C815121
C12C811161 C12C811151
C12C811155 C12C811152
C12C815231 C815182
C815192
5 - EPSON Stylus Pro 7600 and 9600 7/02
Page 5
EPSON Stylus Pro 7600 and 9600

EPSON Paper and Other Media

The papers you can use vary, depending on whether you have the Photographic Dye ink model or the UltraChrome ink model, as shown in the tables below.
NOTE: The Stylus Pro 7600 cannot use paper wider than 24 inches.
Papers supported by Photographic Dye ink model
Paper type Roll sizes Sheet sizes
Premium Glossy Photo Paper (250)
Premium Luster Photo Paper
Premium Semigloss Photo Paper
Premium Semimatte Photo Paper (250)
Photo Paper 13-inch roll: S041233 8.3" 11.7": S041141,
Photo Glossy Paper 24-inch roll: SP91021
Photo Semigloss Paper
Photo Quality Ink Jet Paper
ColorLife Paper Semigloss
Presentation Matte Paper
Doubleweight Matte Paper
Enhanced Matte Paper
Photo
8.3-inch roll: S041376 13-inch roll: S041378 24-inch roll: S041638 36-inch roll: S041639 44-inch roll: S041640
10-inch roll: S041644 20-inch roll: S041645 24-inch roll: S041461 36-inch roll: S041462 44-inch roll: S041463
8.3" × 11.7": S041331
24-inch roll: S041655 36-inch roll: S041656 44-inch roll: S041657
36-inch roll: SP91001 44-inch roll: SP91002
24-inch roll: SP91022 36-inch roll: SP91003 44-inch roll: SP91004
11" × 17": S041070
24-inch roll: S041664 44-inch roll: S041666
24-inch roll: S041295 36-inch roll: S041221 44-inch roll: S041220
24-inch roll: S041385 36-inch roll: S041386 44-inch roll: S041387
24-inch roll: S041595 36-inch roll: S041596 44-inch roll: S041597
11" × 17": S041290
11.7" × 16.5": S041288 13" × 19": S041289
8.3" × 11.7": S041602
11.7" × 16.5": S041406 13" × 19": S041604
13" × 19": S041327
S041271,S041272
8.3" × 11.7": S041140
11.7" × 16.5": S041142 11" × 17": S041156 13" × 19": S041143
8.3" × 23.4" (Panoramic):
S041145
13" × 19": S041069
16.5" × 23.4": S041079 17" × 22": S041171
16.5" × 49.21' (Banner): S041102
8.3" × 11.7": S041603
13" × 19": S041605
Papers supported by Photographic Dye ink model (continued)
Paper type Roll sizes Sheet sizes
Matte Paper ­Heavyweight
Enhanced Matte Posterboard
EPSON Proofing Paper Commercial Semimatte
Glossy Paper Heavyweight
Semigloss Paper Heavyweight
Posterboard Semigloss
Backlight Film 24-inch roll: S041482
8.3" × 11.7": S041257
24" × 30": S041598
13-inch roll: S041668 24-inch roll: S041658 36-inch roll: S041659 44-inch roll: S041660
24-inch roll: S041291 36-inch roll: S041227 44-inch roll: S041226
24-inch roll: S041292 36-inch roll: S041229 44-inch roll: S041228
20.25" × 28.75":
36-inch roll: S041483 44-inch roll: S041484
11.7" × 16.5": S041260 13" × 19": S041263
30" × 40": S041599
S041237 28" × 40": S041236
Papers supported by UltraChrome ink model
Paper type Roll sizes Sheet sizes
Premium Glossy Photo Paper (250)
Premium Luster Photo Paper
Premium Semigloss Photo Paper
Premium Semimatte Photo Paper (250)
Photo Glossy Paper 44-inch roll: SP91002
Photo Semigloss Paper
Doubleweight Matte Paper
Enhanced Matte Paper
8.3-inch roll: S041376 13-inch roll: S041378 24-inch roll: S041638 36-inch roll: S041639 44-inch roll: S041640
10-inch roll: S041644 20-inch roll: S041645 24-inch roll: S041461 36-inch roll: S041462 44-inch roll: S041463
8.3" × 11.7": S041331
24-inch roll: S041655 36-inch roll: S041656 44-inch roll: S041657
36-inch roll: SP91001 24-inch roll: SP91021
44-inch roll: SP91004 36-inch roll: SP91003 24-inch roll: SP91022
44-inch roll: S041387 36-inch roll: S041386 24-inch roll: S041385
24-inch roll: S041595 36-inch roll: S041596 44-inch roll: S041597
11" × 17": S041290
11.7" × 16.5": S041288 13" × 19": S041289
8.3" × 11.7": S041602
11.7" × 16.5": S041406 13" × 19": S041604
13" × 19": S041327
8.3" × 11.7": S041603 13" × 19": S041605
7/02 EPSON Stylus Pro 7600 and 9600 - 6
Page 6
EPSON Stylus Pro 7600 and 9600
Papers supported by UltraChrome ink model (continued)
Paper type Roll sizes Sheet sizes
Enhanced Matte Posterboard
EPSON Proofing Paper Commercial Semimatte
Glossy Paper ­Photo Weight
Watercolor Paper­Radiant White
EPSON Velvet Fine Art Paper*
Somerset Velvet for EPSON Fine Art Paper
Smooth Fine Art Paper*
Textured Fine Art Paper*
Synthetic Paper* 24-inch roll: S041399
Adhesive Synthetic Paper*
Adhesive Vinyl 24-inch roll: S041436
Backlight Film 24-inch roll: S041482
®
Brillion
Tyvek
Canvas 24-inch roll: S041531
NOTE: Check the EPSON Pro Graphics web site (http:// prographics.epson.com) for additional media that may become available.
24" × 30": S041598
13-inch roll: S041668 24-inch roll: S041658 36-inch roll: S041659 44-inch roll: S041660
44-inch roll: S041389 22-inch roll: S041388
13" × 19": S041351
8.5" × 11": S041636
24-inch roll: SP91203 44-inch roll: SP91204
24-inch roll: S041431 36-inch roll: S041432 44-inch roll: S041433
24-inch roll: S041447 36-inch roll: S041448 44-inch roll: S041449
36-inch roll: S041400 44-inch roll: S041401
24-inch roll: S041402 36-inch roll: S041403 44-inch roll: S041404
36-inch roll: S041437 44-inch roll: S041438
36-inch roll: S041483 44-inch roll: S041484
24-inch roll: S041494 36-inch roll: S041495 44-inch roll: S041496
36-inch roll: S041532 44-inch roll: S041533
30" × 40": S041599
13" × 19": S041456
13" × 19": S041637
24" × 30": SP91200 36" × 44": SP91201 44" × 60": SP91202
24" × 30": S041434 36" × 44": S041435
24" × 30": S041450 36" × 44": S041451

Control Panel

Control Panel Lights and Messages

When a problem occurs, a message appears on the display and the lights on the control panel come on or flash.
Error messages
Message/Light Explanation Response
INK LOW
Ink Out light(s) flashing
INK OUT
Ink Out light(s) on
NOT ENOUGH INK
Ink Out light(s) on
NO INK CARTRIDGE
Ink Out light(s) on
WRONG INK CARTRIDGE
INVALID INK CARTRIDGE
Ink Out light(s) on
LOAD PAPER
Paper Out light on
Ink cartridge(s) are nearly empty (printing continues).
Ink cartridge(s) are empty (printing stops).
Not enough ink is available to finish cleaning the print head.
Ink cartridge(s) not installed.
You tried to install the wrong ink cartridge.
Paper lever is in the released position (all the way back) while loading paper.
Make sure you have replacement cartridges available.
Replace the ink cartridge(s) indicated by Ink Out light(s).
Replace the ink cartridge(s) indicated by Ink Out light(s).
Install ink cartridges as indicated by the lights.
If you are installing ink cartridges for the first time, you must install the cartridges that came with your printer.
If you are replacing ink cartridges, check the package and product code. You must use the ink cartridges designed for your printer. Other cartridges will not work.
After you finish loading paper, pull the paper lever all the way forward, to the secured position.
7 - EPSON Stylus Pro 7600 and 9600 7/02
Page 7
EPSON Stylus Pro 7600 and 9600
Error messages (continued)
Message/Light Explanation Response
LOAD ROLL PAPER
LOAD SHEET PAPER
Paper Out light on
PAPER JAM
Paper Out light flashing
PAPER NOT CUT
Paper Out light flashing
PAPER NOT STRAIGHT
Paper Out light flashing
PAPER OUT
Paper Out light on
RELOAD PAPER
Paper Out light on
REMOVE PAPER
Paper Out light on
SET PAPER LEVER
Paper Out light on
Paper source setting in printer software is different from control panel.
Paper has jammed in the printer.
Roll paper was not cut completely.
Cut paper did not fall off.
Paper slipped and fed into the printer at an angle.
No paper is loaded. Load paper.
Paper ran out. Remove any printouts or
Paper could not be reversed into the printing position.
Image is too wide for the paper loaded in the printer.
Paper is not fully ejected.
PAPER NOT CUT error was cleared.
Paper is too thick for head cleaning.
Paper lever was released during the printing process or another operation.
Make sure the right paper is loaded and the paper source setting is the same on the control panel and printer software.
Remove the jammed paper.
Cut the paper manually, remove the cut paper from the printer, then reload paper.
Remove the cut paper from the printer. Reload paper.
Reload paper, making sure the edges are straight and aligned with the vertical row of holes at the paper exit.
paper remaining in the printer and load more paper.
If the message appears during a print job, reset the printer by pressing the Pause button for 3 seconds. Then load paper and resend the job.
Remove the paper. Reload it so that the bottom edge is straight and aligned with the vertical row of holes at the paper exit.
Resize your image or load wider paper.
Cut the paper at the paper insertion slot, then reload paper.
Reload paper.
Pull the paper set lever out to remove the paper. Head cleaning automatically starts. After cleaning, reload paper.
Pull the lever all the way forward, to the secured position. Start printing again from the beginning for best results.
Error messages (continued)
Message/Light Explanation Response
SET INK LEVER The ink lever was left
FRONT COVER OPEN
Pause light on
TURN PRINTER PWR OFF AND ON
UNABLE TO PRINT
MAINTENANCE TANK ALMOST FULL
Maintenance Tank light
flashing
CHANGE MAINTENANCE TANK
All lights flashing
NO MAINTENANCE TANK
Maintenance Tank light is on
OPTION I/F ERROR
SERVICE REQ.
All lights flashing
MAINTENANCE REQ.
COMMAND ERROR
in the unlocked position.
Front cover is open. Close the front cover.
This message appears after you clear a paper jam.
You tried to print while an error condition was present or the ink compartment cover was open.
The maintenance tank is almost full.
The maintenance tank is full.
The maintenance tank is not installed.
Wrong interface card installed.
An error has occurred.
A printer part will need to be replaced soon.
Youre using the wrong printer driver.
Damaged data was sent to the printer.
Pull the lever down to lock the ink cartridges.
Press the Power button to turn the printer off and back on again.
After 3 seconds the message disappears. Press the Pause button to exit SelecType mode. If the message appears again, clear the error before you print.
Make sure you have a replacement maintenance tank.
Replace the maintenance tank.
Make sure the maintenance tank is fully inserted.
Turn off the printer and remove the card. See the documentation that came with the card.
Note the error number, then turn the printer off and back on.
Note the error number and contact EPSON. (If only the cutter blade is worn out, you can replace it yourself.)
Make sure you installed the correct driver for your printer.
To clear the data, press the printer’s Power button to turn the printer off. Wait for about a minute, then turn the printer on again.
7/02 EPSON Stylus Pro 7600 and 9600 - 8
Page 8
EPSON Stylus Pro 7600 and 9600

Printing a Status Check

The status check shows the amount of ink remaining in each cartridge, the page count, and the status of the cutter blade, maintenance tank, and other printer parts.
NOTE: You can replace the ink cartridges, cutter blade, and maintenance tank yourself. Other parts need to be replaced by an authorized EPSON service technician.
Follow these steps to print the status check:
1. Load a sheet of paper in the printer. (You can print test pages on roll paper, but you will use more paper.)
2. Press the SelecType button on the control panel. You see PRINTER SETUP.
3. Press
4. Press
5. Press Enter. The status check sheet prints.
6. Press Pause to exit the Test Print menu.
so you see TEST PRINT, then press
d
. You see
r
NOZZLE CHECK.
so you see STATUS CHECK, then press
d
. You
r
see PRINT.
The amount of ink left or the component life is indicated as follows:
E*****F = full (or full life remaining) E**** F = 3/4 full (or 3/4 life remaining) E*** F = 1/2 full (or 1/2 life remaining) E** F = 1/4 full (or 1/4 life remaining) E* F = nearly empty (or service life near end) E F = empty (or service life ended)

Replacing an Ink Cartridge

The easiest way of checking ink levels is from the control panel:
(almost
(full)
black* black* cyan magenta light cyan light magenta yellow
* If your printer uses UltraChrome ink, the black ink cartridges may be
a combination of Photo Black, Matte Black, or Light Black.
When one of the Ink Out lights is flashing (and INK LOW is displayed on the control panel), the corresponding cartridge is almost out of ink. Make sure you have a replacement cartridge. When the light stays on and INK OUT is displayed, the cartridge is empty. You must replace the cartridge before you can continue printing.
See page 5 for information on selecting the correct replacement cartridges. Before you start, make sure the printer is turned on. Then follow these steps to replace an ink cartridge:
empty)
9 - EPSON Stylus Pro 7600 and 9600 7/02
1. Note the color of the cartridge whose Ink Out light is on or
flashing. This is the cartridge you need to replace.
2. Open the ink compartment cover.
Page 9
EPSON Stylus Pro 7600 and 9600
3. Raise the ink lever to the unlocked position.
4. Remove the empty ink cartridge from the printer.
5. Make sure the replacement cartridge is the correct color, and remove it from its package.
7. Lower the ink lever to its locked position.
8. If you’re using 110 ml cartridges, close the ink compartment cover. If youre using 220 ml cartridges, you’ll have to leave the cover open.
Once the cartridges are installed, the printer returns to its READY state (or says LOAD PAPER if paper isn’t loaded).
If you see the message WRONG INK CARTRIDGE, you may have loaded an incorrect black ink cartridge for the black ink mode youre currently in, or loaded a cartridge containing the wrong type of ink for your printer (Photographic Dye or UltraChrome). Remove any cartridges indicated by a red Ink Out light on the control panel, and replace them with the correct cartridges.
If youre using UltraChrome Ink, gently shake the cartridge before installing it.
6. Hold the cartridge with the arrow pointing toward the printer. Then insert the cartridge into the slot. Dont force it in.

Paper Type and Banding

Banding can be caused by several problems, such as clogged print head nozzles or a mis-aligned print head. It can also be caused by using a paper that is not defined in the EPSON printer driver or in a third-party RIP. To correct this problem, make sure you select the correct paper type in the driver.
If your paper type is not defined, use the printers SelecType menu to create a custom paper type. See Optimizing the Settings for Your Paper in the Printer Guide.

Running a Nozzle Check and Cleaning Cycle

If your printed image is unexpectedly light or faint or dots are missing from the image, you may need to run a cleaning cycle. This unclogs the print head nozzles so they can deliver ink properly.
The cleaning cycle uses ink, so you should run it only if print quality declines. To determine if a cleaning cycle is needed, print a nozzle check (below). You should also print a nozzle check after cleaning to see if the cleaning cycle was successful.
7/02 EPSON Stylus Pro 7600 and 9600 - 10
Page 10
EPSON Stylus Pro 7600 and 9600

Printing a Nozzle Check Pattern

1. Load a letter-size sheet of paper in the printer. (You can print the nozzle check on larger sheets or roll paper, but you will use more paper; youll also have to remove any roll paper before running the cleaning cycle.)
2. Press the SelecType button on the control panel. You see PRINTER SETUP.
3. Press
4. Press
5. Examine the nozzle check pattern. Each staggered
so you see TEST PRINT, then press
d
. You see
r
NOZZLE CHECK.
so you see PRINT, then press Enter. The nozzle
r
check sheet prints.
horizontal and straight vertical line should be complete, with no gaps in the pattern:
If dots are missing from the pattern, as shown below, clean the print head as described in the next section.

Aligning the Print Head

If banding appears on your prints, or vertical lines are not straight, you need to align the print head. Although you can align the print head using the printer software, its best to do this from the control panel. This aligns the print head for all modes and resolutions.
If you havent already done so, its a good idea to run a nozzle check before aligning the print head (page 11). This ensures that the print head alignment patterns print correctly.
1. Make sure the printer is turned on. Then load roll paper that is at least 24 inches wide (you can use the roll paper that came with your printer).
2. Press the SelecType button on the control panel. You see PRINTER SETUP.
3. Press
4. Press
so you see HEAD ALIGNMENT, then press
u
.
r
You see PAPER THKNS.
so that *STD appears on the display. This is the
r
correct thickness setting for most EPSON papers. If you’ll be printing on one of the papers listed below after completing the alignment, use the
u
and
buttons to
d
select the appropriate thickness setting for that paper.

Cleaning the Print Head

1. Make sure no paper is loaded and all of the H Ink Out lights on the printers control panel are off.
If an H Ink Out light is flashing or on, you need to replace the corresponding ink cartridge instead. See page 9 for instructions.
2. Press the Cleaning button and hold it for at least 3 seconds. The Pause light flashes as the printer cleans its print head. The cleaning cycle takes about 60 seconds and does not use any paper.
3. When the Pause light goes off, print the nozzle check again to confirm that the head is clean.
You may need to run the cleaning cycle several times to get a complete nozzle check pattern. For effective cleaning, always run a nozzle check between cycles.
If the lines in the pattern are still missing dots after several cleaning cycles, turn the printer off and leave it overnight, then clean the print head again the following morning. If you still see no improvement, contact EPSON for assistance.
Thickness setting
3N For EPSON Premium Glossy Photo Paper (250) and
0N For film
0.0 to 1.6 mm For non-EPSON media
Paper type
Premium Semimatte Photo Paper (250)
5. Press Enter.
6. Press the
button to select the mode you want to perform
d
the adjustment in (BI-D BLACK, BI-D ALL, or UNI-D ALL).
If youre printing non-photographic images with black ink only, select BI-D BLACK. Otherwise, perform a UNI-D ALL adjustment, followed by BI-D ALL.
7. Press the Enter button to print the alignment patterns.
11 - EPSON Stylus Pro 7600 and 9600 7/02
Page 11
EPSON Stylus Pro 7600 and 9600
8. Once the patterns are done printing, examine the first row (K1) in group #1. You see a pattern similar to that shown below (only part of it is shown in the drawing). Use your own eye loupe or the one that came with the printer to determine which line looks the best. In the example below, the middle line (numbered 5) is the best.
NOTE: You must use at least a 10× eye loupe to check the pattern.
best line in K1
K1
123456
K2
123456
Lc
123456
9. Use the
u
and
d
7
7
best block in K2
7
buttons to select the best line.
10. Press Enter.
11. Examine the black set of blocks (K2) in group #1. Select the block with the smallest gap, then press Enter.

Switching Between Black Ink Modes

If your printer uses EPSON UltraChrome ink, you can switch between black ink modes to optimize your black ink density. When you installed the cartridges that came with your printer, your printer was initialized in Photo Black Mode. You can switch between the three modes shown below:
Mode Image and paper type
Photo Black Mode For printing photographic images on all media
types. Optimized for traditional photographic and ink jet-coated papers, such as EPSON Premium Luster Photo Paper, Photo Semigloss Paper, Premium Semimatte Photo Paper, etc.
Matte Black Mode Optimized for printing photographic images on
matte or plain papers, such as EPSON Enhanced Matte Paper, Smooth and Textured Fine Art Paper, and Somerset Velvet for EPSON, when the highest level of photographic quality is desired.
Dual Matte Black For printing on matte or plain paper, such as
newsprint and plain bond, when print speed is favored over photographic image quality.
After deciding on the black ink mode you want to switch to, make sure you have the black ink cartridge(s) youll be installing. In some cases, youll be replacing only one of the cartridges.
12. Repeat this process for each of the other patterns, when prompted.
13. If number 5 (the current alignment setting) shows the smallest gap for each pattern, the print head is aligned and you can exit the adjustment early by pressing
Pause
. You may need to repeat the alignment more than once to ensure that number 5 is the best choice for all patterns.
14. When done, press Pause to exit the head alignment.
Mode Required cartridges
Photo Black Mode Photo Black and Light Black
Matte Black Mode Matte Black and Light Black
Dual Matte Black Matte Black and Matte Black
Since this process consumes ink from the color cartridges as well as the black ones, you need to make sure there is enough ink in all the cartridges before you begin. Check the
Ink Out
If there is not enough ink in one or more cartridges to carry out the procedure (5% or less), youll be prompted during the procedure to replace the cartridges. If any cartridges are low on ink but not low enough to prevent the procedure from being carried out, you should still make sure you have replacements available, or you will be limited in how much you can print after switching black ink modes.
lights on the control panel:
If an
Ink Out
on or flashing, you’ll need to replace the cartridge
light is
7/02 EPSON Stylus Pro 7600 and 9600 - 12
Page 12
EPSON Stylus Pro 7600 and 9600
If the printers maintenance tank is almost used up, you’ll need to replace it as well. The printer will tell you if it needs to be replaced, but you may wish to check it in advance, as shown below, so you can make sure you have one available, in case its needed.
Maintenance
tank indicator
(showing a
new tank)

Selecting the Black Ink Cartridges

Make sure you have all the needed supplies as described above. Once you remove the ink cartridges from the printer, you must not turn off the printer until you have finished switching black ink modes. Follow these steps to start the process and tell the printer which cartridges you want to install:
1. Make sure the printer is on and READY is displayed on the
control panel.
8. The printer displays a message telling you to release the ink lever and remove the cartridges. Raise the lever and remove all the cartridges; do not re-insert them until instructed to do so.
Be sure to set aside any black ink cartridges you wont be using, so that you dont accidentally re-insert them.

Checking the Maintenance Tank

Once you have removed all the ink cartridges, you may see a message telling you to replace the maintenance tank. If so, pull out the tank from the side of the printer and replace it with a new one. If you dont see this message, continue on to the next section.
2. Press the SelecType button. You see PRINTER SETUP.
3. Press d until you see MAINTENANCE, then press r. You
see PWR CLEANING.
4. Press d so you see BK INK CHANGE, then press r. You
see EXEC.
5. Press Enter. You see SELECT INK SET.
The printer gives you two choices for the new set of black ink cartridges, depending on which ones are already installed (press
or
to see the choices). For example, if
u
d
youre in Photo Black Mode, the printer will let you switch to either Matte Black Mode (#1 MAT: #2 LBK) or Dual Matte Black Mode (#1 MAT: #2 MAT).
6. Make sure you know which cartridges you want to install, then press
or
u
d until the correct set of cartridges is
displayed.
7. Press ENTER.
If you see the message NOT ENOUGH INK, lift the ink lever and remove any low or empty cartridges. (Check the Ink Out lights on the control panel to see which cartridges are low or empty.) Insert the replacement cartridge(s), then lower the ink lever.

Draining the Ink

Once you have removed all the ink cartridges, you see a message that the printer is ready for draining. Follow these steps:
1. Insert the draining cartridge into the slot indicated on the
control panel (#1 or #2 slot). The position is also indicated by the flashing Ink Out light.
2. Lower the ink lever. The printer begins draining the ink delivery system.
3. Once the draining is complete, the printer stops making noise and you see a message telling you to remove the draining cartridge.
If you are replacing both black ink cartridges, you see a message prompting you to insert the draining cartridge in the second slot. Once you do this, the draining process repeats a second time.
13 - EPSON Stylus Pro 7600 and 9600 7/02
Page 13
EPSON Stylus Pro 7600 and 9600

Charging the Ink

Once draining is complete, make sure you have the correct black ink cartridges available for the black ink mode you’re switching to. Then follow these steps:
1. Insert all the ink cartridges into the printer. Be sure to install the correct black ink cartridges for the black ink mode youre switching to.
2. Lower the ink lever. The printer begins charging the ink delivery system.
3. Once the charging is complete, the printer stops making noise and displays READY on the control panel.
Continue on to the next section to update your printer driver software.

Updating the Macintosh Driver

If youre printing from a Macintosh, you need to update the driver so that it knows which black ink mode you’re using. (In Windows, the driver is updated automatically.)
1. Open the Chooser from the Apple menu.
2. Click the printer icon and port, as shown.

Replacing the Cutter Blade

If you notice that your paper isnt cut cleanly, the cutter blade may need to be replaced. If you use the blade to cut heavy stock or non-EPSON media, you may need to replace it more often. You can check the status of your cutter by printing the status check sheet (see page 9).
1. Make sure that the printer is on and the front cover is closed.
2. Press the SelecType button on the control panel. You see PRINTER SETUP.
3. Press
4. Press d until you see CUTTER REPL, then press
5. Press Enter. The carriage moves to the cutter replacement
6. You see a message on the control panel telling you to open
d until you see MAINTENANCE, then press
see PWR CLEANING.
r
see EXEC.
position.
the front cover. Open the cover to access the carriage.
. You
r
. You
Close when done
3. Close the Chooser. This completes the black ink replacement.
Click here . . .
then here
7. Push down on the side pin, then turn the latch to the right.
7/02 EPSON Stylus Pro 7600 and 9600 - 14
Page 14
EPSON Stylus Pro 7600 and 9600
8. Carefully remove the cutter blade. Be careful not to lose the spring.
CAUTION: The blade is sharp. Be careful when removing it.
9. Insert the new cutter as shown.

Replacing the Maintenance Tank

When the maintenance tank is almost full, the Maintenance Tank light on the control panel flashes. When the tank is
completely full, the printer stops working and the
Maintenance Tank
CHANGE MAINTENANCE TANK on the control panel.
You can check how much space remains in the maintenance tank by viewing its indicator on the control panel, shown below.
Maintenance
tank indicator
(showing a
new tank)
Follow these steps to replace the tank:
1. Make sure the printer is not printing or performing any
other operations (READY or PAPER OUT should appear on the control panel).
light stays on. You see the message
10. Push down on the side pin while turning the latch to
the left.
11. Close the front cover. The carriage returns to the
home position and the printer returns to its previous status.
2. Pull out the maintenance tank from the side of the printer.
CAUTION: Be careful not to spill ink from the tank when removing it. Hold it upright at all times.
3. Insert the new tank.

Related Documentation

CPD-14021 EPSON Stylus Pro 7600 and 9600 Printer
Guide
CPD-14020 EPSON Stylus Pro 7600 and 9600 Quick
Reference Guide
15 - EPSON Stylus Pro 7600 and 9600 7/02
Loading...