DORO 5015 User Manual
English
5015
Cordless Telephone with
Caller Identication
User guide
1 Earpiece
2 Display
3 Redial Button
4 Caller Identication
5 Talk button
6 Programming /Recall (R) Button
7 Microphone
8 Erase/Volume
9 CARE-function button
10 Disconnect button
11 Memory button
12 Intercom/Mute
English
Index
Installation 4
Unpacking........................... 4
Connection ......................... 4
Belt Clips............................. 5
Battery ................................ 5
Battery Charge Indicator .... 6
Range ................................. 6
The Display......................... 7
Base Unit Indicators ........... 7
Handset Paging .................. 7
Operation 8
Making a Call ...................... 8
Receiving a Call.................. 8
Redial Button ...................... 8
Volume Control ................... 8
Hold Function ..................... 8
Call Timer ........................... 8
Memory............................... 9
Caller Identication 10
Settings 11
Expanded System 14
General Information............ 14
Multiple Base Units............. 14
Multiple Handsets ............... 15
Register a New Handset/
Base Unit ............................ 15
Intercom Function ............... 16
Transferring Calls Between
Handsets ............................ 16
Conference ......................... 16
Select Base Unit ................. 17
Other 18
Troubleshooting .................. 18
Guarantee (UK) .................. 19
Guarantee/Notes for Australia,
New Zealand ...................... 19
Technical information ......... 21
UK....................................... 21
REN (RN for New Zealand) 21
Declaration of conformity ... 23
Type of Ringer signal .......... 11
Volume of Ringer signal...... 11
Button Click ........................ 11
Auto - Answer ..................... 11
Handset PIN Code.............. 12
Tone/Pulse Dialling ............ 12
Recall Button Timing
(business use only)............. 12
PBX Function...................... 13
Optional Network Services. 13
www.doro.com 3
English
Installation
Unpacking
The package should include the following items:
- Handset - Mains adapter
- Base unit - Line cord
- Battery - Belt clip
Connection
1. Connect the mains adapter to the y socket of the base unit and to an
electrical wall socket.
2. Remove the battery cover from the back of the handset. Insert the battery
plug and t the battery into the handset. Replace the battery cover.
3. Place the handset in the base unit, with the keypad facing outwards. Once the
handset is correctly placed in the base unit, a beep will be heard and the
charge indicator 7 will illuminate on the base unit.
4. Charge the handset battery without interruption for 15 hours.
5. Connect the telephone line cord to the socket marked t on the base unit
and plug into the telephone network socket (using adapter plug if required).
IMPORTANT!
Under power failure conditions, this telephone will not operate. Please ensure that a separate
telephone, not dependent on local power, is available for emergency use. The earpiece of the
handset may attract small ferromagnetic objects such as staples and pins, care should be taken
when placing the handset near these items. Do not place the base unit in areas of high humidity
or where it will be exposed to direct sunlight or other major heat sources.
This model can only be recharged with the keypad set facing
outwards!
4 www.doro.com
English
Installation
Belt Clips
A belt clip is included, which can be tted on the back of the handset. To attach
the clip, press it into place over the back of the handset. On either side of the
handset, there are indents for the clips to clasp onto.
Battery
The telephone comes supplied with an environmentally friendly nickel metal
hydride (NiMH) battery. As with all batteries performance may degrade over
time, should you notice that the standby time has reduced considerably or there
are signs of leakage, the battery pack should be replaced.
A fully charged battery will last for approx. 100 hours in standby or approx. 10
hours call time. These operation times apply at normal room temperature.
A completely discharged battery will take about 15 hours to fully recharge.
Please note that the charge indicator 7 on the base unit is on while charging
and will go out when the battery is fully charged.
The battery charge indicator in the handset display will ash while charging and
will stop ashing when the battery is fully charged.
The equipment has an automatic charging mechanism that prevents the battery
from being overcharged or damaged due to prolonged charging.
Please note!
When the telephone is installed for the rst time, the battery must be charged for 15 hours
before using the telephone.
Use DORO original batteries only. The guarantee does not cover any damages caused by
incorrect batteries.
The handset must be charged with the buttons facing outwards.
Please dispose of any batteries in an environmentally friendly manner.
www.doro.com 5
English
Installation
Battery Charge Indicator
The symbol in the display indicates when it is time to recharge the battery.
The symbol has two segments, which disappear as the battery charge decreases.
When the battery is running low, the symbol will appear in the display and
a warning tone will be heard. If the handset is not recharged at this time, the
phone will cease to function until it is recharged.
Range
The range of the telephone varies depending on various factors in the
surrounding environment. The radio waves transmitting the call may be
hindered by obstructions, reducing the range.
Specied ranges require an unobstructed transmission between the handset and
the base unit. In such ideal conditions, the telephone range can be up to 300
metres. In a densely populated area, house, apartment, etc. the range of the
telephone will be reduced. Try to get the best range by relocating the base unit.
The ideal location for the base unit is a high and unobstructed place.
Out of range warning
If, during a call, the handset is carried too far from the base, a warning tone will
be heard from the handset. Unless the handset is moved closer to the base unit
within a few seconds, the call will be lost.
6 www.doro.com
English
Installation
The Display
Indicator Function
P Programming.
* New number/s in Caller ID log.
Speed dial.
Indicates that a call is connected.
Flashes when the phone rings.
INT z Intercom calls and Mute function.
Battery charge indicator.
6 Shown within range of the base unit. Flashes when out of range.
Base Unit Indicators
* New number/s in Caller ID log.
7 Charging.
o/y
Illuminates when the base unit is connected, and ashes during
call and registration.
Handset Paging
Pressing j on the base unit will activate the paging signal of the handset. This
function is used to help locate the handset or to page the person carrying the
handset. The signal will stop automatically after a while, or if either the l
button on the handset or the j button on the base unit is pressed.
www.doro.com 7
English
Operation
Making a Call
1. Enter the required number. Mistakes can be erased using C.
2. Press o , and the number is dialled.
3. Use l to terminate the call.
Please note!
If the telephone cannot connect to a line, a warning tone will be heard. The problem may be
due to the battery running low, the handset being too far from the base unit or all of the
transmission channels being engaged.
Receiving a Call
1. Wait for the handset to ring.
2. Answer the call by pressing o.
3. Use l to terminate the call.
Redial Button
If the number dialled is engaged or if you wish to redial the last number dialled,
press r and o .
Volume Control
The volume may be adjusted during a call using .
Hold Function
A call can be temporarily put on hold using the i button. Press it once more to
resume the previous call. The call cannot be resumed from another phone.
The display shows INT z as long as the call is on hold.
Call Timer
Following the connection of a call, a timer is shown on the display. The timer
helps you keep track of how long the call lasts.
8 www.doro.com
Loading...