D-link DFL-700 Quick Installation Guide

This product can be set up usingThis product can be set up using

This product can be set up using

This product can be set up usingThis product can be set up using anan

y curry curr

y curr

anan

y curry curr

Internet Explorer 6 or NetscapeInternet Explorer 6 or Netscape

Internet Explorer 6 or Netscape

Internet Explorer 6 or NetscapeInternet Explorer 6 or Netscape NN

aviavi

avi

aviavi

enen

t Wt W

t W

t Wt W

eb breb br

eb br

eb breb br

enen

gator 6 or abovegator 6 or above

gator 6 or above

gator 6 or abovegator 6 or above

owserowser

owser

owserowser

, i.e, i.e

, i.e

, i.e, i.e

.,.,

DFL-700

™™

™

™™

ETET

Security FirewallSecurity Firewall

Security Firewall

Security FirewallSecurity Firewall

EFENDEFEND

EFEND

EFENDEFEND

NetworkNetwork

Network

NetworkNetwork

Before You Begin

If you purchased this Network Security Firewall to connect to your high-speed Internet connection in a secure manner, you must have either an Ethernet-based Cable or DSL modem with an established Internet account from an Internet Service Provider (ISP).

Check Your Package Contents

These are the items included with your DFL-700 purchase:

DFL-700 NETDEFEND™ Network Security Firewall

CD-ROM (containing Manual and Warranty)

Ethernet (CAT5 UTP/Straight-Through) Cable

Console Cable (RS-232)

Using a power supply

5V DC Power Adapter

If any of the above items are missing, please contact your reseller.

specifications subject to change without notice. DFL-700. 05192004

with a different voltage rating will damage this product and void its warranty.

Connecting The DFL-700 Network Security Firewall To Your Network

A. Connect the power adapter to the receptor on the back panel of the DFL-700 and

then plug the other end of the power adapter to a wall outlet or power strip. The Power LED will turn ON to indicate proper operation.

B. Power off your Cable or DSL modem; some devices may not have an on/off switch

and will require you to unplug the power adapter. Now, the DFL-700 should be powered on and the Cable / DSL modem should be turned off. Cable / DSL modem (Power Off) – DFL-700 (Power On)

C. Attach an Ethernet cable to the Ethernet jack located on the Cable / DSL modem.

After the Ethernet cable is securely connected, power on the Cable / DSL modem by turning on the unit or plugging in the power adapter. Cable / DSL modem (Power On) – DFL-700 (Power On)

D. Attach the other end of the Ethernet cable to the W AN port on the back panel of

the DFL-700. The WAN LED light will illuminate to indicate proper connection. If the WAN LED is not illuminated, please go back to step B and repeat the steps.

E. Attach an Ethernet cable in the LAN port on the back panel of the DFL-700 and

connect it to a port on your network hub or switch. The LED light for the LAN port on the DFL-700 will illuminate to indicate proper connection.

F. Connect the computer that you will use to configure the DFL-700 to the network

hub or switch.

DMZ port: Connects to

the DMZ network.

COM Port: Connects to your

computer’s COM port using the provided Console Cable.

LAN port: Connects

the local area network.

WAN port: Connects to

the Cable or DSL modem.

Power Receptor:

Connection for the Power Adapter.

Connecting The DFL-700 Network Security Firewall To Your Network (continued)

STA TUS LED: Flashes consistently to indicate that the DFL-700 is working properly .

POWER LED: A solid light indicates a proper connection to the power supply .

When you have completed the steps in this Quick Installation Guide, your connected

network should look similar to this:

NETWORK LEDs: A solid light on the port indicates a good connection. The LEDs blink during data transmission.

Using The Setup Wizard

T o obtain a new IP address from the DFL-700 you may need to restart your computer or release and renew your IP address. First make sure that the network adapter in your computer is configured properly. Instructions for configuring the network adapter to obtain an IP address automatically from the DFL-700 can be found in the Appendix.

The DFL-700 provides Web based configuration. Y ou can configure your DFL-700 using a Web browser such as Internet Explorer or Netscape Navigator in Windows, Macintosh, or UNIX based environments.

Open your Web browser and type

http://192.168.1.1 into the URL

address box. Then press the Enter or Return key .

(The IP Address shown in the example above is the default setting. If you’ve changed the IP Address of the DFL-700 to conform to a network then input that IP Address instead of the default IP Address.)

Welcome to the DFL-700 connection wizard!

Here you can choose to either configure your firewall over HTTP or over Secure HTTP (HTTPS).

Click on Connect to the unit via

HTTPS instead to use Secure HTTP

Click Next to keep using HTTP

+ 8 hidden pages