Note: Using a power supply with a different voltage than the one included with
your product will cause damage and void the warranty for this product.
If any of the above items are missing, please contact your reseller.
Product Overview
Package Contents
• Screws
• I/O Connector
• Alignment Paper
• Manual and Software on CD
• Quick Install Guide
System Requirements
• Windows® XP or Windows Vista
• At least 256MB of memory (512MB recommended)
• An available Ethernet connection
• Internet Explorer 6.x or higher Internet Web Browser
• VGA card resolution: 800x600 or above
• CPU: 1.7GHz or above processor (2.8GHz plus processor with 512MB memory and a 32MB video card is required for
multiple camera viewing and recording in IP surveillance program)
™
4D-Link DCS-6110 User Manual
Section 1 - Product Overview
Introduction
DCS-6110 fixed dome network camera is cost-effective and an ideal security solution providing high quality real-time videos in
MPEG-4 and JPEG compression for small to medium-sized businesses, office and homes. The DCS-6110 features 3G mobile
video support, enabling you to view a live video feed from your camera on a compatible 3G mobile phone or PDA anywhere in
your 3G coverage area. The 3G mobile video support allows you to monitor a remote location without using a computer or an
internet connection. In addition supports dual stream output for simultaneous live monitoring and high resolution recording.
D-ViewCam software is also included to manage up to 32 cameras simultaneously from your computer, send automated e-mail
alerts, and record video to your hard drive when motion is detected. The DCS-6110 is a deluxe-size dome network camera, giving
you a more professional look to your business or location making it an excellent choice for home and business surveillance.
Note: Use of video equipment for recording the image of a person without their knowledge and consent is prohibited in certain states
or jurisdictions. Nothing herein represents a warranty or representation that the D-Link product provided herein is suitable for the
end-user’s intended use under the applicable laws of his or her state. D-Link disclaims any liability whatsoever for any end-user use
of the D-Link product, which fails to comply with applicable state, local, or federal laws.
exceptional picture quality. Use D-Link’s SoC (system-on-chip) products to provide high quality real-time video
compression in MPEG-4 and Motion JPEG formats. DCS-6110 supports simultaneous dual-streaming for live
monitoring and recording. With the free-bundled 32-channel recording software, the DCS-6110 is an ideal solution
for high quality viewing and reliable recording.
Features
• Sharp Image Monitoring From Different Angles
and thus prevents possible damage that maybe caused by a burglar. This network camera has a built-in three axis
mechanism for wall mount installation. The DCS-6110 provides high quality real-time videos in MPEG-4 and JPEG
compression with VGA/QVGA/QQVGA resolution. It is suitable for narrow space surveillance, like an elevator.
• View Live Video from a 3G Mobile Phone
network by using a compatible cell phone or PDA with a 3G video player. Anywhere within the 3GPP service area, users
are offered a flexible and convenient way to remotely monitor a home or office in real time.
• Wired PoE Access - For effective surveillance in and around a building, this camera comes with a built-in 802.3af
compliant Power Over Ethernet (PoE) module, which eases the installation process and also gives you the freedom
to place the camera where it’s needed. In addition, the 10/100BASE-TX Ethernet port is also provided for convenient
connection to an Ethernet network or to a broadband Internet via a gateway router.
• Smart & Easy To Use - The software allows you to view up to 32 cameras on a single computer screen at one central
location. Users can set up automated e-mail alerts to be instantly informed of unusual activities. Fixed dome cameras
usually uses fixed focus lens, but the DCS-6110 also has a vari-focal lens. Vari-focal lens provides easier installation
process because the board lens of dome camera is not like CS/C mount lens, it is not changeable. Drop ceiling bracket
is another alternative option for an installation method. In addition, this network camera supports the Universal Plugn-Play feature, which allows computers running on Windows 2000/XP/Vista to automatically recognize the camera
and adds it to the network. Sign up with one of the free Dynamic DNS services available on the web, to assign a name
and domain to the camera (e.g.mycamera.dlinkddns.com). This allows users to remotely access the camera without
having to remember the IP address.
- The live camera feed of the camera can be pulled from the 3G cellular
- The DCS-6110 is recommended for indoor ceiling mounting,
6D-Link DCS-6110 User Manual
Section 1 - Product Overview
• Supports a Variety of Protocols - The DCS-6110 supports a wide variety of protocols such as RTSP, FTP, SMTP, NTP
and HTTP. In addition, supports UPnP and DDNS. DDNS allows your camera to be accessed using a static host name
rather than an IP address. UPnP allows Windows XP users to install the camera with a single mouse click.
• Web Configuration - Using a Web browser, administrators can configure and manage the network camera directly from
its own Web page via the Intranet or the Internet. Up to 20 user names and passwords are permitted, with privilege
settings controlled by the administrator.
• Connection to External Devices - Supporting auxiliary Input/Output connectors, you can connect the Network Camera
to a variety of external devices such as IR-sensors, switches and alarm relays. Combined with programmable alarming
equipment, you can develop a variety of security applications that are triggered on alarm-based events. The Network
Camera provides an industry standard in/out external connector for connectivity.
Note: Use of audio or video equipment for recording the image or voice of a person without their knowledge and consent is prohibited in
certain states or jurisdictions. Nothing herein represents a warranty or representation that the D-Link product provided herein is suitable
for the end-user’s intended use under the applicable laws of his or her state. D-Link disclaims any liability whatsoever for any end-user use
of the D-Link product, which fails to comply with applicable state, local, or federal laws.
7D-Link DCS-6110 User Manual
Section 1 - Product Overview
Hardware Overview
Connections
DC Power Connector
The DC power input connector is
located on the side panel of the
DCS-6110 labeled 12VDC with a
single socket to supply power to
the network camera.
Ethernet Cable Connector (PoE)
The network camera’s side panel features an RJ-45
connector for connections to 10Base-T Ethernet
cabling or 100Base-TX Fast Ethernet cabling. This
network port supports the NWay protocol, allowing
this network camera to automatically detect or
negotiate the transmission speed of the network.
The Ethernet port can also be used to power the
camera by using a PoE switch.
Focus Controller
Zoom Controller
Adjustment Screw
Tilt Screw
DI/DO
Pan Screw
Reset Button
Reset is initiated when the reset button is
pressed once and held until the power LED
flashes through its cycle twice.
8D-Link DCS-6110 User Manual
Section 1 - Product Overview
Power/Activity LED
Hardware Overview
LEDs
9D-Link DCS-6110 User Manual
Section 1 - Product Overview
Hardware Installation
When Mounting to a Ceiling
Find a suitable place to install the camera using the installment stencil. Place the camera
at the desired operating location and insert the screws through the two holes located at
the base of the camera. Use screwdriver to tighten and secure.
When Mounting to a Wall
Find a suitable place to install the camera by using the installment stencil to find a desired
operating location on the wall. Drill two pilot holes where the holes of the installment
stencil are located. Insert the supplied plastic anchors into the drilled holes, and align
the holes at the base of the camera with the plastic anchors. Once aligned, insert the
provided screws through the holes with screwdriver to tighten and secure.
10D-Link DCS-6110 User Manual
Section 1 - Product Overview
Network Deployment
General Connection (without PoE)
Connect the network camera to a hub via Ethernet cable.
Connect the supplied power cable from the camera to a power outlet.
Connection with a PoE Hub/Switch
If using a PoE hub/switch, connect the network camera to the hub/switch via Ethernet
cable, which will provide transmission for both power and data over a single cable.
11D-Link DCS-6110 User Manual
Section 2 - Installation
Software Installation
Turn on the computer and insert the D-Link DCS-6110 Autorun CD into the CD-ROM drive. The following step-by-step instructions
displayed are shown when using Windows Vista operating system. The steps and screens are similar when using other Windows
operating systems.
Click on Installation Wizard
to begin software installation.
The Installation Setup Wizard window will pop up. Click Next to
continue.
Click Next
12D-Link DCS-6110 User Manual
Section 2 - Installation
Click I Agree to accept the License Agreement.
Click I Agree
Click the Browse button if you would like to change the destination of
installation, otherwise click Install to continue.
Note: Installation may take several minutes to complete.
Click Install
13D-Link DCS-6110 User Manual
Section 2 - Installation
To start the installation click Install.
Note:The installation may take several minutes to complete.
Click Finish to complete installation and the D-Link Installation Wizard window will pop up for camera configuration.
Click Finish
14D-Link DCS-6110 User Manual
Section 3 - Configuration
Configuring Your Camera with the Installation Wizard
If the D-Link Installation Wizard window does not pop up after completion of software installation, click on the icon that was
created in your Windows Start Menu.
The Installation Wizard will appear and show the MAC address and IP address of the DCS-6110, which may appear to be different
from the actual address depending on what your device is connected to. If you have a DHCP server on your network, there will
be a valid IP address displayed here.
Note:A DHCP server is a device that supplies the same IP address.
To begin setup, single-click on the DCS-6110 located in the camera list and
click Manual Setup located on the left of the Installation Wizard.
Click Manual Setup
15D-Link DCS-6110 User Manual
Section 3 - Configuration
Enter a password, and confirm the password for the admin ID and click
Next.
Note: The default administrator username is set to admin and the password
may be left blank. The password can be changed after installation.
Click Next
16D-Link DCS-6110 User Manual
Section 3 - Configuration
PPPoE Setup
The Network Type screen displays will pop up to ask if you want to setup a
PPPoE for the device. Click No for quick setup and skip to the next page .
Note: By using PPPoE, users can virtually dial from one machine to another over an Ethernet
network, establish a point to point connection between them and then securely transport
data packets over the connection.
The PPPoE Setting screen displays. Enter the username and password provided
by your ISP to connect to the Internet by PPPoE.
Click Next and skip to the setup screen as seen in page 19.
Click Next
17D-Link DCS-6110 User Manual
Section 3 - Configuration
Check the Get IP by DHCP Server automatically box to obtain a new IP
address every time the camera starts up. Click Next to continue.
Click Next
Select UPnP Port Forwarding if your router supports this function. If not, choose Manual to manually enter your port numbers. Click Next to continue.
Click Next
18D-Link DCS-6110 User Manual
Section 3 - Configuration
Click Next to continue.
Click Next
A window will pop up asking you if you want to access the DCS-6110 via
mobile phone. Clicking Yes will set the video resolution to 176x144.
19D-Link DCS-6110 User Manual
Section 3 - Configuration
Click Apply to apply the settings listed in the window to the device.
Application may take a few minutes to process.
Click Apply
A window will pop up to confirm application was successful. Click OK
to continue.
A new window will pop up displaying the lists to access your device,
click Add to my favorite to save the address then click Exit to complete
installation.
Click Exit
20D-Link DCS-6110 User Manual
Section 3 - Configuration
Double-click DCS-6110 in the Installation Wizard window to launch the
camera’s web configuration.
Note:Please see the user manual for more information.
Enter admin as the default username and leave the password blank. Click
OK to continue.
21D-Link DCS-6110 User Manual
Section 3 - Configuration
This section shows your camera’s live video. You can control your settings using the buttons below. For more information on using
the web configuration, please refer to the user manual.
22D-Link DCS-6110 User Manual
Section 3 - Configuration
Loosen
Tighten
Tighten
Loosen
Tighten
Loosen
Loosen
Tighten
Adjusting the Lens
Based on the live image retrieved from the camera, adjust the camera lens by performing the following procedures:
Adjusting the Viewing Angle
Loosen the pan screw and turn the lens module left and right until the desired position is achieved; tighten the pan screw when
completed.
Loosen the tilt screws on both sides of the camera, and turn the lens module up and down until the desired position is achieved;
tighten the tilt screws once completed.
Loosen the image adjustment screw and turn the lens to adjust the network camera’s image until the desired orientation is
achieved, tighten the image adjustment screw once completed.
Adjusting Zoom and Focus
Loosen the zoom controller and adjust the zoom factor by moving
the controller left and right until the desired range is achieved;
tighten the zoom controller once completed.
Loosen the focus controller and adjust the focus range by moving
the controller left and right until the image is clear; tighten the focus
controller once completed.
23D-Link DCS-6110 User Manual
Section 3 - Configuration
Attaching the Enclosure
Once the lens is properly adjusted, rearrange the light shield so that it will not obstruct the lens during surveillance.
Place the dome enclosure over the network camera so that the LED sticker on the dome
enclosure is properly aligned with the camera’s LED. Insert the supplied screws into the
two holes located at the base of the dome enclosure, tighten until secure.
Place the ring enclosure over the dome enclosure. Once placed, gently turn the ring
enclosure clockwise until it locks and is securely attached to the dome enclosure.
Note: When attaching the ring enclosure, be sure to first align the line on the ring enclosure with the
triangle on the dome enclosure. When attachment is successful, the line on the ring enclosure will be
aligned with the line on the dome enclosure.
24D-Link DCS-6110 User Manual
Section 3 - Configuration
Web-based Configuration Utility
This section will show you how to configure your new D-Link Network Camera using the Web-based Configuration Utility.
To access the configuration utility, open a web-browser such
as Internet Explorer and enter the IP address of your Network
Camera (http://192.168.0.120)
Note: In the example, this address is 192.168.0.120. Your address
may differ.
Type Admin in the user name field and leave the password
blank by default.
Note: You may refer to page 51 to change the password
for your admin account.
Click OK
25D-Link DCS-6110 User Manual
Loading...
+ 57 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.