D-link DCS-4622 User Manual

Version 2.00 | 08/27/2018
User Manual
Vigilance 360° Full HD PoE Network Camera
DCS-4622
Preface
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Information in this document may become obsolete as our services and websites develop and change.
Revision Date Description
1.00 09/13/2016 DCS-4622 Revision A1 with rmware version 1.00
1.01 02/24/2017 Minor updates
2.00 08/27/2018 DCS-4622 Revision B1 with rmware version 2.00
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Copyright © 2018 D-Link Corporation.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation.
2D-Link DCS-4622 User Manual
Table of Contents
Product Overview ........................................................4
Package Contents ................................................................. 4
Introduction ............................................................................ 5
System Requirements ......................................................... 5
Features .................................................................................... 6
Hardware Overview ............................................................. 7
Installation ...................................................................9
Mounting the Camera .........................................................9
Software Installation ......................................................12
Conguration ............................................................15
Using the Conguration Interface ................................15
Live Video ..............................................................................17
Setup .......................................................................................20
Setup Wizard ....................................................................20
Network Setup .................................................................25
Advanced ...............................................................................43
ICR and IR ...........................................................................43
HTTPS .................................................................................. 44
Access List ..........................................................................45
SNMP ...................................................................................46
Maintenance .........................................................................48
Device Management .....................................................48
System ................................................................................49
Firmware Upgrade ..........................................................50
Status ......................................................................................51
Device Info ........................................................................51
Logs .....................................................................................52
Help......................................................................................53
Technical Specications ............................................54
Regulatory Information ............................................ 57
Dynamic DNS ...................................................................28
Image Setup .....................................................................29
Audio and Video ..............................................................31
Preset ...................................................................................32
Motion Detection ...........................................................33
Time and Date ..................................................................34
Event Setup .......................................................................35
SD Card ...............................................................................42
3D-Link DCS-4622 User Manual
Section 1: Product Overview
DCS-4622 Vigilance 360° Full HD PoE Network Camera
Mounting Kit
CD-ROM with User Manual and software
Quick Installation Guide
Product Overview

Package Contents

If any of the above items are missing, please contact your reseller.
Safety Notice: Installation and servicing should be done by certied technicians so as to conform to all local codes and prevent voiding your warranty.
4D-Link DCS-4622 User Manual
Section 1: Product Overview

Introduction

Congratulations on your purchase of the DCS-4622 Vigilance 360° Full HD PoE Network Camera. The DCS-4622 is a professional surveillance and security solution for small, medium, and large enterprises alike. The DCS-4622 uses a Full HD progressive scan CMOS sensor; the professional sensor results in low noise and high sensitivity capabilities ideal for surveillance applications.
The DCS-4622 is a complete system with a built-in CPU and incorporates a web server, allowing it to transmit excellent real­time Full HD resolution video for security and outdoor surveillance.
The DCS-4622 can be accessed remotely, controlled and congured from any PC/Notebook over your local network or through the Internet via a web browser. The simple installation and intuitive web-based interface oer easy conguration across the full range of its advanced feature set, including granular control over multiple video streams with dierent congurations and multicast video streams which helps you manage your network load.
The built-in removable IR-cut lter and IR LEDs give the DCS-4622 the capability to view up to 8M at night. The DCS-4622 also incorporates Power over Ethernet (PoE), allowing it to be easily installed in a variety of locations without the need for supplemental power cabling. The combination of an IR-Cut Filter, IR LEDs, and PoE make the DCS-4622 an ideal solution for a dependable and cost-eective 24 hour surveillance solution with easy clutter-free installation.

System Requirements

• Computer with Microsoft Windows® 10, 8, 7, or Vista® (for CD-ROM Setup Wizard), Mac OS X, or Linux
• Internet Explorer 7, Firefox 20, or Safari 6 or higher
• Existing 10/100 Ethernet-based network with an available 802.3af Power over Ethernet (PoE) port
5D-Link DCS-4622 User Manual
Section 1: Product Overview

Features

360 Degree Surveillance
The built-in sheye lens gives you a full 360 degrees of coverage, allowing it to monitor an entire room with ease. It can also be placed on a wall for 180 degree coverage of a hallway. Distortion correction gives you a panoramic view or a normal corrected image that you can pan across easily.
Supports a Variety of Platforms
With support for TCP/IP networking, HTTP, and other Internet related protocols, the DCS-4622 can also be integrated easily into other Internet/ Intranet applications because of its standards-based features. The DCS-4622 works with any 10/100 Ethernet network, making the DCS-4622 easy to integrate into your existing network environment.
Advanced Event Management
The DCS-4622 can be set up to send e-mail notications with snapshots when an event occurs, such as when motion is detected. Events can be triggered from several sources, such as motion detection and time based events.
IR LEDs for Day and Night Functionality
The built-in infrared LEDs enable night time viewing of up to 20 meters.
PoE (Power over Ethernet) for Flexible Installation
The DCS-4622 can draw all the power it needs from a PoE switch or PoE injector for a simple and clutter-free installation.
Remote Monitoring Utility
The D-ViewCam application adds enhanced features and functionality for the Network Camera and allows administrators to congure and access the Network Camera from a remote site via Intranet or Internet. Other features include image monitoring, recording images to a hard drive, viewing up to 32 cameras on one screen, and taking snapshots.
6D-Link DCS-4622 User Manual
Section 1: Product Overview
1

Hardware Overview

11
10
2
3
4
5
9
14
8
6 7
12
13
7D-Link DCS-4622 User Manual
Section 1: Product Overview
1 Speaker (on back) Onboard speaker for 2-way communication.
2 IR LEDs (behind cover) Provide illumination for low-light environments.
3 Camera Lens Fixed lens to record video of the surrounding area.
4 Light Sensor
5 Power/Status LED
6 Microphone Records audio from the surrounding area.
7 microSD Card Slot You can insert a microSD card to save snapshots and video to it.
8 Camera Mount
9 Tilt Adjustment Screw
10 Mounting Plate Use the holes on the mounting plate to mount the camera to a ceiling or wall.
11 Cable Channels
12 Power Connector Connects to an optional 12 V / 1.5 A power adapter (not included).
13 Ethernet Jack RJ-45 connector for Ethernet to connect the camera to your network.
The light sensor measures the lighting conditions and switches between color and infrared accordingly.
Red: Camera is on, but not connected to the network Green: Camera is on and is connected to the network Flashing Green: Camera is currently streaming video
Remove the camera from the camera mount by turning the camera counter-clockwise. Lock the camera in the camera mount by turning the camera clockwise.
Can be loosened to adjust camera angle, or removed when separating the camera cover from the mounting plate.
The camera cable can be passed through the cable channels or the center of the camera mount when mounting it.
14 Reset Button Press and hold for 10 seconds to reset camera back to the factory default settings.
8D-Link DCS-4622 User Manual
Section 2: Installation

Installation

Mounting the Camera

It is highly recommended that you congure and test your camera before mounting it.
Use a screwdriver to unscrew the tilt adjustment screw. Pull the mounting plate away from the camera mount.
Place the mounting plate where you want to position the camera and use a pencil to mark the two mounting holes.
If you wish to run the camera cables through the wall or ceiling, mark the center hole as well.
Use a 6 mm drill bit to make the required holes approximately 25 mm deep, then insert the wall anchors into the holes. Use the screws provided to attach the mounting bracket to the wall.
If you wish to run the camera cables through the wall or ceiling, drill the center hole for the camera cables to pass through.
9D-Link DCS-4622 User Manual
Section 2: Installation
Use an Ethernet cable to connect the camera's Ethernet jack to your PoE switch or injector. If you are not using PoE to power the camera, you may connect a 12V
1.5A power adapter to the power connector.
Attach the camera mount to the mounting plate.
If you are running the camera cables out the side of the camera, guide the camera cables through the cable channel on the camera mount.
If you wish to run the camera cables through the wall or ceiling, pull the cables through the hole.
10D-Link DCS-4622 User Manual
Section 2: Installation
Adjust the angle of the camera, then screw in the tilt adjustment screw until it is snug.
If you wish to insert a microSD card, remove the camera from the camera mount by turning the camera counter-clockwise and lifting it away from the camera mount.
Insert the microSD card with the contacts facing you.
Reattach the camera to the camera mount and turn it clockwise to lock it in place.
11D-Link DCS-4622 User Manual
Section 2: Installation

Software Installation

Step 1
Insert the DCS-4622 CD into your computer's CD-ROM drive to begin the installation.
If the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start automatically, click the Start button and type D:\autorun.exe (where D: represents the drive letter of your CD-ROM drive) and press Enter.
Step 2
Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu (Start > D-Link > Setup Wizard SE).
12D-Link DCS-4622 User Manual
Section 2: Installation
Step 3
The Setup Wizard will appear and display the MAC address and IP address of your camera(s). If you have a DHCP server on your network, a valid IP Address will be displayed. If your network does not use a DHCP server, the network camera's default static IP 192.168.0.20 will be displayed.
Select your camera, then click the Wizard button to continue.
Step 4
Enter the Admin ID and password. When logging in for the rst time, the default Admin ID is admin with the password left blank.
Click the checkboxes if you wish to change the admin ID and password for the camera, and enter the new ID and password you wish to use.
Click Next to continue.
13D-Link DCS-4622 User Manual
Section 2: Installation
Step 5
Select DHCP if your camera obtains an IP address automatically from a DHCP server such as a router. Select Static IP if you want to manually enter the IP settings for the camera.
Click Next to continue.
Step 6
Take a moment to conrm your settings and click Restart.
14D-Link DCS-4622 User Manual
Section 3: Conguration
Conguration
Using the Conguration Interface
After completing the Camera Installation Wizard, you are ready to use your camera. The camera’s built-in Web conguration utility is designed to allow you to easily access and congure your DCS-4622. At the end of the wizard, click Link, or enter the IP address of your camera into a web browser, such as Firefox. To log in, use the User name admin and the password you created in the Installation Wizard. If you did not create a password, the default password is blank. After entering your password, click OK.
Step 1
Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu (Start > D-Link > Setup Wizard SE).
Step 2
Select the camera and click Link to access the web conguration.
The Setup Wizard will automatically open your web browser to the IP address of the camera.
15D-Link DCS-4622 User Manual
Section 3: Conguration
Step 3
Enter admin as the default username and leave the password blank. Click OK to continue.
Step 4
Enter a password to use for your camera, then click the Save button.
You will be directed to the Live View page, and you can now start using and conguring your camera.
16D-Link DCS-4622 User Manual
Section 3: Conguration

Live Video

This section shows your camera’s live video. You may select any of the available icons listed below to operate the camera. You may also select your language using the drop-down menu on the left side of the screen.
Motion Trigger Indicator
Recording Indicator
Control Pad This control pad can be used to electronically pan, tilt, and
Auto Pan Click this to start automatically panning the currently
Stop Click this to stop any auto pan or preset sequence actions.
Patrol After creating a list of preset ePTZ camera positions, click this
This indicator will change color when a trigger event occurs.
Note: The video motion feature for your camera must be enabled.
When a recording is in progress, this indicator will change color.
zoom (ePTZ) within the camera's predened view area, if one has been dened. Click on the arrows to move the view in that direction. Click on the inside buttons to zoom in and out of the image. Click the center to return to the home position.
selected view.
to automatically cycle through the preset sequence.
Presets only apply to the square viewing windows in Multi-View with Fisheye, Multi-View, and Mixed View display modes.
17D-Link DCS-4622 User Manual
Section 3: Conguration
Display Modes
Please note that presets only apply to the square viewing panels and are not used with Fisheye View or Panoramic View.
Fisheye View This shows the full camera view.
Normal View This shows a corrected view that you can move by using the
directional controls.
This is the only view that will be available if the camera's Mount Type is set to Wall in Setup > Image Setup. For more details, refer to Image Setup on page 29.
Multi-View with Panorama
Panoramic View This shows a full 360° horizontal view across 2 video panels.
Mixed View This shows 3 normal corrected views with a full sheye
Multi-View This shows a multi-panel view. Each panel is distortion
Pan/Tilt/
Zoom/
You can set how fast the camera will pan/tilt/zoom/auto pan or move through your preset sequence.
Auto Pan/ Sequence
Speed
This shows a multi-panel view, with a full panorama in the bottom panel. The top video panels are distortion corrected and their positions can be adjusted by clicking the panels and using the directional controls.
You can pan the views left and right by using the directional controls.
view in the top-right panel. Each normal view is distortion corrected and their positions can be adjusted by clicking the panel and using the directional controls.
corrected and their positions can be adjusted by clicking the panel and using the directional controls.
Fisheye View
Multi-View with Panorama
Mixed View Multi-View
Normal View
Panoramic View
Home
Denition:
Language:
Click the Set as Home button to set the current position as the camera's home position.
You may select the interface language using this menu.
18D-Link DCS-4622 User Manual
Section 3: Conguration
Video Prole 1/2 Select a video prole to use. For more on setting up your
video proles, refer to Audio and Video on page 31.
Full Screen Mode
Take a Snapshot This will save a snapshot to your PC using the storage folder
Record a Video Clip
Set a Storage Folder
Listen/Stop Audio In
Talk/Stop Audio Out
Go To:
You can move the currently selected view to one of your preset positions by selecting it from the drop-down menu.
This will switch to a full-screen view of your camera's video. Double-click or press the Esc key to exit full-screen mode.
you have selected. This will start recording a video clip to your PC using the
storage folder you have selected. Click it again to stop recording. If you close the browser window, the recording will stop.
Select a storage folder to save snapshots and video clips to.
Toggles incoming audio from the camera's microphone on and o.
Toggles outgoing audio from your PC's microphone to the camera's speaker on and o.
19D-Link DCS-4622 User Manual
Section 3: Conguration

Setup

Setup Wizard

To congure your Network Camera, click Internet Connection Setup Wizard. Alternatively, you may click Manual Internet Connection Setup to manually congure your Network Camera and skip to Network Setup on page 25.
To quickly congure your Network Camera’s motion detection settings, click Motion
Detection Setup Wizard. If you want to enter your settings without running the wizard, click Manual Motion Detection Setup and skip to Motion Detection on page 33.
20D-Link DCS-4622 User Manual
Section 3: Conguration
Internet Connection Setup Wizard
This wizard will guide you through a step-by-step process to congure your new D-Link Camera and connect the camera to the Internet. Click Next to continue.
Select how the camera will connect to the Internet.
If your camera is connected to a router, or you are unsure how your camera will connect to the Internet, select DHCP Connection.
Select Static IP if your Internet Service Provider has provided you with connection settings, or if you wish to set a static address within your home network. Enter the correct conguration information and click Next to continue.
If you are using PPPoE, select Enable PPPoE and enter your user name and password.
Click Next to continue.
21D-Link DCS-4622 User Manual
Loading...
+ 46 hidden pages