Table of Contents
Table of Contents
Product Overview ........................................................3
Package Contents ......................................................................... 3
System Requirements ................................................................. 3
Introduction ...................................................................................4
Features ............................................................................................5
Hardware Overview ..................................................................... 6
Hardware Installation .................................................................. 8
Software Installation .................................................................10
Configuration ............................................................. 22
Setup Wizard Conguration ...................................................22
Web-based Conguration Utility ..........................................25
Live Video ......................................................................................26
Camera ...................................................................................26
Setup ...............................................................................................27
Wizard .....................................................................................27
Internet Connection Setup Wizard ...............................27
Motion Detection Setup Wizard ....................................31
Snapshot ................................................................................46
Digital Output ......................................................................47
Advanced ICR .......................................................................48
RS-485 .....................................................................................49
Maintenance ................................................................................50
Device Admin .......................................................................50
System ....................................................................................51
Firmware Upgrade ..............................................................52
Status ..............................................................................................53
Device Info ............................................................................53
Logs .........................................................................................54
Help .................................................................................................55
D-ViewCam Installation .............................................56
Add a Camera ...............................................................................59
Troubleshooting .........................................................64
DI/DO ........................................................................... 67
Network Setup .....................................................................34
Wireless Setup ......................................................................36
Dynamic DNS .......................................................................37
Image Setup .........................................................................38
Audio and Video ..................................................................39
Motion Detection ...............................................................41
Time and Date ......................................................................42
Recording ..............................................................................43
How to save video to a shared folder? ........................44
Networking Basics .................................................... 69
Check your IP address ...............................................................69
Statically Assign an IP address ...............................................70
Technical Specifications ...........................................71
2D-Link DCS-3411/3430 User Manual
Section 1 - Product Overview
• D-Link DCS-3411/3430 Day & Night Network Camera
• CAT5 Ethernet Cable
• Power Adapter
• Manual and Software on CD
• Quick Install Guide
• Camera Stand
• 2 Antennas (DCS-3430 only)
Note: Using a power supply with a dierent voltage than the one
included with the package will cause damage and void the warranty
for this product.
Product Overview
Package Contents
If any of the above items are missing, please contact your reseller.
System Requirements
• Windows® XP or Windows Vista
• At least 256MB of memory (512MB recommended)
• An available Ethernet connection
• Wireless 802.11n network (for DCS-3430 only)
• Internet Explorer 6.x or higher Internet Web Browser
• VGA card resolution: 800x600 or above
• CPU: 1.7GHz or above processor (2.8GHz plus processor with 512MB memory and a 32MB video card
is required for multiple camera viewing and recording using the D-ViewCam software)
®
3D-Link DCS-3411/3430 User Manual
Section 1 - Product Overview
Introduction
The D-Link DCS-3411/3430 Day & Night Network Camera is a powerful surveillance system that can connect to your
network. The DCS-3411/3430 diers from a conventional PC Camera because it is a stand-alone system with a built-in
CPU and Web server, providing low-cost solution capable of solving demanding security and home/oce monitoring
needs. It is designed with an aluminum cast for maximum heat dissipation and better protection. Snapshot enables you
to save a snapshot image directly form a Web browser to a local hard drive without installing any software. H.264 can
reduce the size of video stream around 80% compared with the Motion JPEG and as much as 50% when compared with
MPEG4. Using less network bandwidth and storage space allows the DCS-3411/3430 to be a very cost eective network
camera. With 0.5 lux light sensitivity, the DCS-3411/3430 is capable of capturing video in rooms with minimal lighting.
With optional Day & Night Auto Iris lens, IR LED lens or night vision illuminator, you can customize your surveillance
application to enable low light or night vision video streaming. You can also zoom in using the DCS-3411/3430’s 16x
digital zoom feature. The DCS-3411/3430 gives you the ability to monitor video and audio in you home/oce using an
Internet browser anywhere in the world! Simple installation procedures, along with the built-in Web-based interface
oers easy integration to your network environments.
Note: Use of audio or video equipment for recording the image or voice of a person without their knowledge and consent
is prohibited in certain states or jurisdictions. Nothing herein represents a warranty or representation that the D-Link
product provided herein is suitable for the end-user’s intended use under the applicable laws of his or her state. D-Link
disclaims any liability whatsoever for any end-user use of the D-Link product, which fails to comply with applicable
state, local, or federal laws.
4D-Link DCS-3411/3430 User Manual
Section 1 - Product Overview
Features
• Multiple Stream Types: Choose between H.264 / MPEG4 / MJPEG depending on the type of application the camera is being
used for. When using H.264 you can reduce the bandwidth and storage needs by up to 80% when compared to MJPEG or
by up to 50% when compared with MPEG4.
• Supports a Variety of Protocols: Supporting TCP/IP networking, SMTP e-mail, HTTP and other Internet related protocols,
the DCS-3411/3430 Network Camera can be integrated easily into other Internet/Intranet applications because of its
standards-based features.
• Remote Snapshot Images: Using the Snapshot feature, you save snapshots directly from the Web browser to a local hard
drive without installing any software, making it convenient to instantly capture any moment from a remote location.
• Low Light Recording and 16x Digital Zoom: The DCS-3411/3430’s 0.5 lux light sensitivity allows you to capture video in rooms
with minimal lighting, making it ideal for use at night time. The camera also features 16x digital zoom for closer viewing.
• Optional Day & Night Auto iris lens, IR LED Lens or night vision illuminator
to enable low light or night vision video streaming.
• Web Conguration: Using the Web browser, administrators can congure and manage the Network Camera directly using the web
browser via Intranet or Internet. Up to 10 accounts with dierent settings can be created and controlled by the administrator.
• Built-in BNC (Bayonet Neil-Concelman) connector is used for professional video connections. It benets users who integrate
digital IP camera into traditional system (CCTV) for both analog and digital video streaming purposes.
• Powerful Surveillance and Remote Monitoring Utility: An administrator is assigned with a pre-dened user ID and password,
can modify the Network Camera settings from a remote site via Intranet or Internet. Administrators are allowed to monitor
the video image, record the video image to a hard drive, and take snapshots.
• Broad Range of Applications: With today’s high-speed Internet, the Network Camera provides the ideal solution for remotely
monitoring live video images over the Intranet and Internet. The DCS-3411/3430 allows remote access using an Internet
Explorer or web browser for live image viewing with audio and allows the administrator to manage and control the Network
Camera anywhere and anytime. Apply the Network Camera to monitor various objects and places such as homes, offices,
banks, hospitals, child-care centers, amusement parks and other varieties of industrial and public monitoring. The Network
Camera can also be used for intruder detection with its motion-detection mode, capture still images and video images for
archiving and many more applications.
2
, you can customize your surveillance application
5D-Link DCS-3411/3430 User Manual
Section 1 - Product Overview
Hardware Overview
Ethernet Cable Connector (PoE only with 3411)
The Network Camera’s back panel features an RJ-45
connector for connections to 10Base-T Ethernet cabling
or 100Base-TX Fast Ethernet cabling. This network port
supports the NWay protocol, allowing the Network Camera
to automatically detect or negotiate the transmission speed
of the network.
Audio Out Connector
The DCS-3411/3430 provides an Audio
Out connector to be used for 2-way
audio. Speakers (not included) may
be connected to the camera to provide
audio for 2-way communication.
BNC
The BNC connector is used for professional
video connections. It benefits users who
integrate digital IP camera into traditional
system (CCT V) for both analog and digital
video streaming purposes.
Iris Level
Used only when the DC-Iris lens
is connected to the camera. When
adjusting the Iris level, you can
determine the brightness of the
video images.
Reset Button
Reset will be initiated when the
reset button is pressed once and
held until the Power LED flashes
through its cycle twice.
Microphone Connector
Th e DC S-3 411 /34 30 Day & Nigh t
Ne t wo r k Ca mer a has an int er n a l
microphone built-in. However, you
have the option of using an external
microphone by plugging it into the
microphone connector.
6D-Link DCS-3411/3430 User Manual
Section 1 - Product Overview
Hardware Overview
DC Power Connector
The DC power in put connector is
located on the DCS-3411/3430 Network
Camera’s back panel and is labeled
12V DC with a single socket to supply
power to the Network Camera.
Antenna Connectors (DCS-3430)
Connects to the wireless antennas.
I/O Connector
The DCS-3411/3430 provides a terminal block with
three pairs of connectors situated on the back panel.
Two pairs are for input and the other is for output. The
I/O connectors provide the physical interface to send
and receive digital signals to and from a variety of
external devices.
Power LED
The power LED is on the back of the
camera. As soon as the power adapter
is connected to the camera, the LED
will turn red. Once a connection has
been established via Ethernet port, the
LINK LED will turn solid green. If trac
is passing to the camera the LINK LED
will blink. If no Ethernet connection is
detected the LINK LED will not light up.
Link LED
Once a connection has been established via
Ethernet port, the LINK LED will turn solid green.
If trac is passing to the camera the LINK LED
will blink. If no Ethernet connection is detected
the LINK LED will not light up.
7D-Link DCS-3411/3430 User Manual
Section 1 - Product Overview
Hardware Installation
Attach the Antennas (DCS-3430 only)
Locate the antennas included with your DCS-3430, and attach them to the antenna connectors
located on the back of the DCS-3430.
Connect the Ethernet Cable
Connect an Ethernet cable to the network cable connector located on the Network
Camera’s back panel and attach it to the network.
Attach the External Power Supply
Attach the external power supply to the DC power input connector located on the Network
Camera’s back panel (labeled DC 12V) and connect it to an AC power outlet.
Note: When you have a proper connection, the LED will turn red. The light may cycle on
and o and your computer may show an intermittent loss of connectivity, this is normal
until you have congured your Network Camera.
Connect Using Power-Over-Ethernet
Once you connect an Ethernet cable to your PoE switch or adapter, the Power LED on the DCS-3411/3430 will turn red to
indicate a proper connection.
8D-Link DCS-3411/3430 User Manual
Section 1 - Product Overview
The Network Camera comes with a camera stand with a swivel ball screw head that can be attached to the Network
Camera bottom socket cavity. Attach the camera stand to the Network Camera and station it for your application. There
are holes located in the base of the camera stand allowing the Network Camera to be mounted to the ceiling, or any
wall securely.
Socket for camera stand
9D-Link DCS-3411/3430 User Manual
Section 2 - Installation
Software Installation
Turn on the computer and Insert the D-Link DCS-3411/3430 Driver CD in the CD-ROM drive. The step-by-step instructions
that follow are shown in Windows® XP. The steps and screens are similar for the other Windows operating systems.
Click Setup Wizard
If the CD Autorun function does not automatically start on your computer, click Windows Start > Run. In the Run command
box type “D:\DCS-3411_3430.exe”, where D: represents the drive letter of your CD-ROM. If it does start, proceed to the next
screen.
10D-Link DCS-3411/3430 User Manual
Section 2 - Installation
Click Next to continue.
Click Next
Click Yes to accept the License Agreement.
Click Yes
11D-Link DCS-3411/3430 User Manual
Section 2 - Installation
To start the installation click Next.
Note: The installation may take several minutes to complete.
Click Next
12D-Link DCS-3411/3430 User Manual
Section 2 - Installation
Click Finish to complete the installation.
Click Finish
13D-Link DCS-3411/3430 User Manual
Section 2 - Installation
Now, click on ffdshow from the autorun screen. This will install the proper codecs that will allow you to playback video
taken by the DCS-3411/3430.
Click ffdshow
Click I Agree
14D-Link DCS-3411/3430 User Manual
Section 2 - Installation
Select Language, and then click OK.
Click OK
Click Next
15D-Link DCS-3411/3430 User Manual
Section 2 - Installation
Click Next
Click Next
16D-Link DCS-3411/3430 User Manual
Section 2 - Installation
Click Next
Click Next
17D-Link DCS-3411/3430 User Manual
Section 2 - Installation
Click Next
Click Next
18D-Link DCS-3411/3430 User Manual
Section 2 - Installation
Select the speaker from your PC, and then click Next.
Click Next
Click Install
19D-Link DCS-3411/3430 User Manual
Section 2 - Installation
Installing
Click Finish
20D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Configuration
This section will show you how to congure your new D-Link Network Camera using the Setup Wizard.
Setup Wizard Configuration
Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu.
Click D-Link Setup Wizard SE
21D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
The Setup Wizard will appear and show the MAC address of the
DCS-3411/3430 and an IP Address (which may or may not be correct
depending on what you have your DCS-3411/3430 connected to).
If you have a DHCP server on your network, there will be a valid IP
Address displayed here. Click the Wizard button to continue.
Note: A DHCP server is a device that supplies the IP address.
Enter the admin ID and password.
Note: The default Admin ID is admin with the password left blank.
Click Next
22D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Select DHCP if you want to obtain a new IP address every time the
camera boots up.
Click Next
Select static IP to use the same IP address at each boot up.
Click Next
23D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Click Restart to save your settings and reboot the Network Camera.
Click Restart
Click the button labeled Link to access the web configuration
page. The Setup Wizard will automatically open your web browser
to the IP address of the DCS-3411/3430, in this example it is:
http://192.198.0.185. Your DCS-3411/3430 may have a different
IP Address.
Click Link
24D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Web-based Configuration Utility
This section will show you how to configure your new D-Link Network Camera using the Web-based Configuration
Utility.
To access the conguration utility, open a web-browser
such as Internet Explorer and enter the IP address for
your Network Camera (http://192.168.1.179)
Note: For example, the address is 192.168.1.179. Your
address may dier.
Enter Admin for the username and then leave the
password blank by default.
Note: To change your password at a later time, please refer
to page 50.
Click OK
25D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Live Video
Camera
This section shows your camera’s live video. You may select the available thumbnails for your option of predened Video
Profile, Full Screen mode, and action items of taking Snapshot, Recording, Set Storage Folder, Listen, Talk, and
Digital Output. You may also select your language setting using the drop-down menu.
You can zoom in and out of the live video image using your mouse. Right-click to zoom out and left-click to zoom in on
the image.
Digital Input
Indicator:
Motion Trigger
Indicator:
Recording
Indicator:
Video Profile 1
Video Profile 2
Video Profile 3
Video Profile 4
Full screen mode
Taking a Snapshot
Recording a Video Clip
Set a Storage Folder
This indicator will light up when there is an
available digital input signal.
When a trigger event occurs, this will light
up.
Note: The video motion feature for your
camera must be enabled.
When a recording is in progress, this indicator
will light up.
Listen/Stop Listening
Talk/Stop Talking
Start/Stop Digital Output
26D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Setup
Wizard
To quickly configure your Network Camera, click Internet
Connection Setup Wizard, or click Manual Internet
Connection Setup to manually configure your Network
Camera.
To quickly congure your Network Camera’s motion detection
settings, click Motion Detection Setup Wizard and skip to
page 31. If you want to enter your settings without running
the wizard, click Manual Motion Detection Setup and skip
to page 41.
Internet Connection Setup Wizard
This wizard will guide you through a step-by-step process to congure your new D-Link Camera and connect the camera
to the internet. Click Next to continue.
Click Next
27D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Select DHCP if you are unsure which settings to pick. Click
Next to continue and skip to page 29.
Click Next
Select Static IP if your Internet Service Provider has
provided you with connection settings, or you wish to
set a static address within your home network. Enter the
accurate information for your static IP setting. Click Next
to continue.
Click Next
28D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
If you are using PPPoE, select Enable and enter your
user name and password, otherwise select Disable and
click Next to continue.
Click Next
If you have a Dynamic DNS account and would like the
camera to update your IP address automatically, Select
Enable and enter your host information. Click Next to
continue.
Click Next
Enter a name for your camera and click Next to continue.
Click Next
29D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Congure the correct time to ensure that all events will
be triggered, captured and scheduled at the right time.
Click Next to continue.
Click Next
If you have selected DHCP, you will see a summary
of your camera’s settings. Please note down all this
information as you will need it for accessing your camera
within the network. Click Apply to save your settings.
Click Apply
If you have selected Static IP, you will see a summary
of your camera’s settings. Please note down all this
information as you will need it for accessing your camera
within the network. Click Apply to save your settings.
Click Apply
30D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Motion Detection Setup Wizard
This wizard will guide you through a step-by-step process to configure your new D-Link Camera motion detection
functions. Click Next to continue.
Click Next
This section will allow you to enable or disable motion
detection as well as control the sensitivity or your
camera’s ability to detect movement. You can select the
Drawing Mode to draw or erase the motion area in your
window of live video.
Click Next
31D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
This step allows you to specify how you will receive the
events notication of your camera, either via using email
or FTP. You will need to enter all the relevant information
for your email account or FTP settings. Then, click Next
to continue.
Click Next
32D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
You have completed the Motion Detection Wizard. Click
Apply to activate your settings.
Click Apply
33D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Network Setup
Use this section to congure the network connections for you camera. All relevant information must be entered accurately.
LAN Settings:
DHCP:
Static IP
Address:
IP Address:
Subnet Mask:
Default
Gateway:
Primary DNS:
Settings for your local area network.
Select this connection if you have a DHCP server running
on your network and would like a dynamic IP address to
be updated to your camera automatically.
You may obtain a static or fixed IP address and other
network information from your network administrator
for your camera. A static IP address will ease you for
accessing your camera in the future.
The xed IP address.
The default value is “255.255.255.0.” Used to determine
if the destination is in the same subnet.
The gateway used to forward frames to destinations in
a different subnet. Invalid gateway settings may cause
the failure of transmissions to a dierent subnet.
Primary domain name server that translates names to
IP addresses.
Secondary
DNS:
Enable UPnP:
Secondary domain name server to backup the primary
one.
Enable this setting to allow your camera to be congured
as an UPnP device in your network.
34D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Enable UPnP port
forwarding:
Enable PPPoE:
User Name:
Password:
HTTP Port:
RTSP port:
Enable this setting to allow the camera to add port forwarding entries into the router automatically.
Enable this setting if you network is using PPPoE service.
The unique name to your account. You may obtain this information from your ISP.
The password to your account. You may obtain this information from your ISP.
The default value is 80.
The port number that you use for RTSP streaming to mobile devices, such as mobile phones or PDAs. The default port
number is 554.
35D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Wireless Setup
This sections allows you to setup and congure the wireless settings for your camera.
Enable Wireless:
Site Survey:
SSID:
Wireless Mode:
Channel:
Authentication:
Select to enable wireless conguration.
Select the wireless connection you would like to
use from the pull-down menu.
Enter the name of you wireless network.
Use the dropdown box to select the mode of
the wireless network you wish to connect to.
Infrastructure is normally used to connect to
an access point or router. Ad-Hoc is usually
used to connect directly to another computer.
If you are using Ad Hoc mode, select the
channel of the wireless network you wish to
connect to, or select Auto.
Select the authentication you use on your
wireless network - Open, Shared (WEP),
WPA-PSK, or WPA-PSK2.
Encryption:
Key:
Signal:
If you use WPA-PSK or WPA-PSK2 authentication, you will need to specify whether your wireless network uses TKIP or
AES encryption. If you use Open or Shared authentication, this setting will be automatically set for you.
If you use WEP, WPA-PSK, or WPA-PSK2 authentication, enter the Key (also known as password) used for your wireless
network.
Indicates the strength of the wirelss signal between the camera and the access point.
36D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Dynamic DNS
DDNS (Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem
when it has been modied. The user name and password are required when using the DDNS service.
Enable DDNS:
Server
Address:
Host Name:
User name:
Password:
Timeout:
Status:
Click to enable the DDNS function.
Select your Dynamic DNS provider from the pull
down menu or enter the server address manually.
Enter the host name of the DDNS server.
Enter your user name or e-mail used to connect
to the DDNS
Enter your password used to connect to the
DDNS server.
This sets the number of hours between DDNS
updates.
Indicate the connection status, automatically
determined by the system.
37D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Image Setup
In this section, you may congure the video image settings for your camera. Preview of the image will be shown in the
window of Live Video. Click Save Settings to activate and save your changes.
Brightness:
Contrast:
Flip:
B/W:
Saturation:
Sharpness:
An adjustable setting to compensate for backlit
scenes.
Adjust to control the contrast of colors between
the object. This feature will help improve images
under a dull grey sky.
Select this feature when your camera is installed
upside down on the cealing
Select to enable or disable black and white mode
for you camera.
This setting controls the strength of color from
black and white to bold colors.
Adjust the sharpness of images. Sharper images
will be displayed when the number is higher. If
the number is lower, a blurrier image will be
displayed.
Mirror:
Frequency:
Select this feature to obtain a mirror image.
You may chose 50Hz or 60Hz frequency. It may
depend on the country where you reside.
38D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Audio and Video
You may congure 4 video proles with dierent setting for your camera. Additionally, you may also congure your
audio (speakers and microphone) setup for your camera. Prole 3 is set as the prole for snapshot, while prole 4 is
sef for your mobile phone or PDA device.
Resolution:
FPS:
Jpeg Quality:
BPS:
This option allows the user to choose the video
resolution of the camera between 160x120, 320x240
and 704x480:
• QQVGA @ 160x112 - Usually used for only displays
of handheld devices.
• QVGA @ 320x240 - Standard solution for mobile
phones and PDAs.
• VGA @ 640x480 - Standard solution for computer
display.
(Frames Per Second): Highest FPS represents highest
refresh rate of a picture is updated on screen every
second, and provides better quality of video.
Select the image quality level you wish to use for the
JPEG images captured.
(Bits Per Second): BPS will aect the bit rate of the video
recorded by the camera. Higher bit rate will increase the
video quality.
RTSP URL:
Analog Output:
Is the URL name used to connect to the camera when
viewing from a mobile device or PDA.
Select the display system of Analog Video Output on the
back NTSC or PAL.
39D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Select On to use auto exposure or Off to use auto IRIS.
Auto
Exposure:
Audio Setup:
Enable
Speaker:
Speaker
Volume:
Enable
Microphone:
Microphone
Volume:
You may switch the external speaker and microphone on/o or adjust the volume.
Enabling this feature allows you to talk using a PC microphone. Your voice will be transmitted to the external speaker
connected to the camera.
You can adjust the speaker volume by using the volume level setting.
Enable this feature to hear audio from the IP Camera’s microphone.
You can adjust the MIC Port volume by using the volume level setting.
40D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Motion Detection
Enabling Video Motion will allow your camera to use the motion detection feature. You may also draw out the motion
area for the monitoring.
Enable Video
Motion:
Sensitivity:
Draw motion
area:
Erase motion
area:
Check this option to turn on the motion detection
feature for your camera.
Set the measurable difference between two
sequential images that would indicate motion.
Select this option to draw out the motion detection
area by dragging your mouse in the window
(indicated by the red-colored box).
Select this option to erase your motion detection
area by dragging your mouse in the window.
41D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Time and Date
From this section, you may automatically or manually congure, update and maintain the internal system clock for your
camera.
Time Zone:
Enable Daylight
Saving:
Auto Daylight
Saving:
Set date and
time manually:
Offset:
Synchronize
with NTP
server:
NTP Server:
Select your time zone from the drop-down menu.
Select this to enable the daylight saving time.
Select this option so that your camera will congure
the Daylight Saving setting automatically.
Select this option so that you may congure the
Daylight Saving date and time manually.
Sets the amount of time to be added or removed
when Daylight Saving is enabled.
Enable this feature to obtain time configuration
automatically from NTP server.
Network Time Protocol (NTP) synchronizes the
DCS-3411/3430 with an Internet time ser ver.
Choose the one that is closest to your location.
Set the date
and time
manually:
Copy Your
Computer’s
Time Settings:
This option allows you to set the time and date
manually.
This will synchronize the time information from
your PC.
42D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Recording
In this section, you can congure and schedule the recording setting for your IP camera.
Enable Recording:
SD Card:
Samba Auth:
Server:
Shared Folder:
Test:
Samba Status:
Resolution:
When Storage is
full:
Select this option to enable the recording feature.
Selecting this will allow you to record to a SD Card inserted into
the SD slot on the right side of the unit. When recording to the
SD card, you can only use Event Based recording.
To access your account on the Samba network drive, enter your
account or anonymous username and password.
The name of your Samba server.
The name of the shared folder used for recording.
Click this thumbnail to verify the connection status of your
camera to the Samba network drive.
Displays the connection status that is determined by the system.
You can click Get Status to refresh the status.
Select your pre-dened prole from the drop-down menu.
When the recording storage area is full, you may choose to stop
recording, or recycle the recording les so that your camera can
record the video continuously.
Event Based:
Prerecord:
Postrecord:
Continous:
Scheduled:
Records when Motion Recording, Digital Input 1, or Digital Input
2 is triggered.
A preset amount of time before motion recording is triggered.
A preset amount of time after motion recording is triggered.
Select to continuously record.
Select this option to manually schedule and configure the
starting and ending time for the recording.
43D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
How to save video to a shared folder?
1. Set the folder in your computer to shared. You can set as anonymous authentication or set a user name and
password.
44D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
2. Click Enable Recording.
3. Set the Samba Authentication to Anonymous
or Account. Enter the IP address of the
computer or network attached storage with
the shared folder and the name of the shared
folder in step 1 to record to. If you selected
Account, enter the user name and password
from step 1.
4. Set the recording and schedule options.
5. Click Save Settings. The status will be set to
Normal when connected properly.
45D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Snapshot
Enable the Snapshot feature so that your camera can take snaphots and send it to your email address or FTP
server.
Enable Snapshot:
Event Based:
Continous:
Scheduled:
Send to
E-mail Address:
FTP Server:
Host name:
Path:
Filename Prefix:
Enable or disable snapshot event.
Select one or more of the events such as Motion
Detection, D/I Signal 1 and D/I Signal 2 for the
source that triggers the action.
Select to continuously record.
Select this option to manually schedule and
configure the starting and ending time for the
recording.
Select this option if you want to receive snapshot
images in your e-mail.
Select this option if you want to receive your
snapshot images via FTP.
The host name of your FTP server.
The directory or path where the images will be
uploaded to (for example: \pub\images).
The prex that will be added to the lename of
each le.
Port:
Passive mode:
The port of the FTP server. The default port is 25.
Some FTP servers allow clients to use passive mode
when connecting to an FTP, which uses random
ports for transfers.
46D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Digital Output
You may enable the Digital Output (DO) feature and congure the source of event for your camera.
Enable D/O
signal:
Trigger Event:
This enables the D/O to send a signal when there
is a triggered event.
You can choose from one or up to three events,
such as Motion Detection, D/I Signal 1, and D/I
Signal 2 for the sources of the triggered events.
47D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Advanced ICR
ICR - IR-Cut Removable(ICR) lter is a switch mechanical design with two dierent sensor lters. It provides the best
lighting conditions for day and night.
Automatic:
Day mode:
Night mode:
Scheduled
Mode:
Selecting this feature will automatically set to
the day mode during daylight and to the night
mode during the night or in dark places.
Selecting this mode will disable the IR Cut
Filter.
Selecting this mode will enable the IR Cut
Filter.
This mode will allow you to enter the desired
time frames for the ICR lter.
48D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
RS-485
You may congure the RS-485 settings or communication specications (baud rate, data bit, stop bit, and parity bit) for
your camera. RS-485 is a serial communication method for computers and devices. For your camera, RS-485 is used
to control a PAN/TILT device, such as an external camera enclosure to perform PAN and TILT movement.
Support PAN-TILT:
Protocol:
ID:
Baud Rate:
Data Bit:
Stop Bit:
When enabling Support PAN-TILT, a control panel will be
displayed on the Live Video page allowing control through
RS-485 for an external camera enclosure.
Select one protocol type from the pull-down menu.
Range from 1 to 255, is the identifier for each RS-485
devices.
Range from 2400 to 38400 bps. It is a speed measurement for
communication between a transmitter and receiver, indicates
the number of bit transfers per second. Higher baud rate
will reduce the distance of the two devices (transmitter and
receiver). By default, the value is 2400.
Either 7 or 8. It is a measurement of the actual data bits in a
transmission. By default, the value is 8.
Either 1 or 2. It is used to signal the end of communication for a
single packet. The more bits used for stop bits, the greater the
lenience in synchronizing the dierent clocks but the slower
the data transmission rate. Bye default, the value is 1.
Parity Bit:
Choices of No, Even, and Odd. It is a simple form of error
checking used in serial communication and you may use no
parity. For even and odd parity, the serial port sets the parity
bit (the last bit after the data bits) to a value to ensure that the
transmission has an even or odd number of logic-high bits.
For example, if the data is 011, for even parity, the parity bit
is 0 to keep the number of logic-high bits even. If the parity is
odd, the parity bit is 1, resulting in 3 logic-high bits.
49D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Maintenance
Device Admin
You may modify the name and administrator’s password of your camera, as well as add and manage the user accounts
for accessing the camera. You may also use this section to create the unique name and congure the OSD setting for
your camera.
Admin password
setting:
Add user account:
User name:
Password:
User List:
Camera Name:
Enable OSD:
Set a new password for the administrator’s
account.
Add new user account.
The user name for the new account.
The password for the new account.
All the existing user accounts will be displayed
here. You may delete any accounts included on
the list.
Create a unique name for your camera, in which
you can access the camera by using this name in
your web-browser.
For example: http://DCS-3411/3430 (By default).
Select this option to enable the On-Screen Display
feature for your camera.
Label:
Show time:
LED Light:
The label name.
Select this option to enable the time-stamp display
in the video screen.
Chose On or Off.
50D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
System
In this section, you may backup, restore and reset the settings as well as reboot your camera.
Save To Local Hard
Drive:
Local From Local
Hard Drive:
Restore To Factory
Default:
Reboot Device:
You may save and document your current
conguration settings into your computer.
Locate a pre-saved configuration by clicking
Browse and then restore the pre-dened settings
to your camera by clicking Load Configuration.
You may reset your camera and restore the factory
settings to your camera by clicking Restore
Factory Defaults.
This will restart your camera.
51D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Firmware Upgrade
Your current rmware version and date will be displayed on your screen. You may go to the D-Link Support Page to
check for the latest rmware version available.
To upgrade the firmware on your DCS-3411/3430, please download and save the latest firmware version from the
D-Link Support Page to your local hard drive. Locate the le on your local hard drive by clicking the Browse button.
Then, open the le and click the “Upload” button to start the rmware upgrade.
Current firmware
version:
Current Product
Name:
File Path:
Upload:
It will be automatically determined and displayed
by the system.
Name of the existing product.
Locate the le (upgraded rmware) on your hard
drive by clicking Browse.
Start uploading the new firmware to your
camera.
52D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Status
Device Info
This page displays all the details information about your device and network connection.
53D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Logs
This page displays the log information of your camera. You may download the information by clicking Download or
delete the log information by clicking Clear.
54D-Link DCS-3411/3430 User Manual
Section 3 - Configuration
Help
55D-Link DCS-3411/3430 User Manual
Section 4 - D-ViewCam Installation
D-ViewCam Installation
D-ViewCam software is included for the administrator to manage up to 32 D-Link IP cameras remotely. You may now use
the software to congure all the advanced settings for your cameras. D-ViewCam is a comprehensive management tool
for IP surveillance.
Insert the CD-ROM into the CD-ROM drive. A menu screen will appear as shown below.
Click D-ViewCam
D-ViewCam provides English, Traditional Chinese and Simplified
Chinese language versions. Select a language version and click OK to
continue.
Click OK
56D-Link DCS-3411/3430 User Manual
Section 4 - D-ViewCam Installation
Click Next to continue.
Click Next
Click Browse if you would like to choose a specific folder for the
installation, otherwise click Next to continue.
Click Next
57D-Link DCS-3411/3430 User Manual
Section 4 - D-ViewCam Installation
Click Next to start the installation.
Note: The D-ViewCam installation process may take several minutes to
complete.
Click Next
Click Finish to complete the installation.
Click Finish
58D-Link DCS-3411/3430 User Manual
Section 4 - D-ViewCam Installation
Add a Camera
This section will show you how to start and add a camera to the D-ViewCam system.
To start D-ViewCam, select Start > All Programs > D-Link >
D-Link D-ViewCam.
Enter Admin as the default user name and leave the password
blank. Click
Camera Wizard.
Note: Please refer to page 51 in the D-ViewCam user manual
to change your password.
/ OK to log into the system and access the Add
59D-Link DCS-3411/3430 User Manual
Section 4 - D-ViewCam Installation
Welcome to the Add Camera Wizard. Use this wizard to add your cameras to the D-ViewCam system.
Note: Use the left or right arrow to navigate the wizard.
Click
/ Next to continue.
Click Next
60D-Link DCS-3411/3430 User Manual
Section 4 - D-ViewCam Installation
Choose which method to add your camera(s). You can choose Auto
Discovery to automatically search for your camera(s), or choose Add
Manually to add your camera(s) via the camera’s IP address. Click Next
to continue.
If you choose Auto Discovery, the system will search all available
cameras that are located on the same LAN with same subnet. The system
will place all the cameras under the default map called My Map. Click
Next to continue.
If you choose Add Manually, enter the IP address or domain name, http
port, model name, camera ID and password.
Click the “?” button to auto detect the camera’s model name, then the
model name will appear in the Model Name box.
Click Next to continue.
61D-Link DCS-3411/3430 User Manual
Section 4 - D-ViewCam Installation
D-ViewCam shows the detected IP camera(s) information. You can choose and schedule the recording for each
camera.
• 24/7 Continuous Recording: Continuously recording 24 hours a day, 7 days a week.
• 24/7 Motion Detection Recording: Continuously monitoring but ONLY recording when motion is detected.
• Ofce Hours Only: Continuously monitoring during oce hours (08:00 AM to 06.00 PM) and ONLY recording
when motion is detected.
• Non-Ofce Hours Only: Continuously monitoring during non-oce hours (06:00 PM to 08.00 AM) and ONLY
recording when motion is detected.
Note: Excluding 24/7 Continuous Recording, other schedule recording types can ONLY do recording when motion is
detected. Please refer to page 35 in the D-ViewCam manual for more information.
Click Next to continue.
62D-Link DCS-3411/3430 User Manual
Section 4 - D-ViewCam Installation
Select Yes to add other camera(s), or select No if you have no additional
camera(s) to be added. Click Next to continue.
The Add Camera wizard is now complete. Click Close to access the D-ViewCam’s main screen.
Your D-ViewCam Installation is Complete!
Note: Please refer to the D-ViewCam user manual for information
about using D-ViewCam.
63D-Link DCS-3411/3430 User Manual
Section 5 - Troubleshooting
Troubleshooting
1. What is an Network Camera?
The Network Camera is a stand-alone system connecting directly to an Ethernet or Fast Ethernet network. It diers
from a conventional PC Camera, the Network Camera is an all-in-one system with built-in CPU and Web-based
solutions providing a low cost solution that can transmit high quality video images for monitoring. The Network
Camera can be managed remotely, accessed and controlled from any PC/Notebook over an Intranet or the Internet
from a Web browser.
2. What is the maximum number of users that can be allowed to access DCS-3411/3430 simultaneously?
The maximum number of users that can log onto the Network Camera at the same time is 10. Please keep in mind
the overall performance of the transmission speed will slow down when many users are logged on.
3. What algorithm is used to compress the digital image?
The Network Camera utilizes MPEG-4 simple prole image compression technology to provide high quality images.
4. Can I capture still images from the Network Camera?
Yes you are able to capture still images with the snapshot function from the software application CD supplied with
the Network Camera or with the snapshot function on the Home page using an Internet browser.
5. Can the Network Camera be used outdoors?
The Network Camera is not weatherproof. It needs to be equipped with a weatherproof case to be used outdoors
and it is not recommended.
6. When physically connecting the Network Camera to a network what network cabling is required?
The Network Camera uses Category 5 UTP cable allowing 10 Base-T and 100 Base-T networking.
7. Can the Network Camera be setup as a PC-cam on a computer?
No, the DCS-3411/3430 Network Camera is used only on an wireless 802.11n, Ethernet or Fast Ethernet
network.
64D-Link DCS-3411/3430 User Manual
Section 5 - Troubleshooting
8. Can the DCS-3411/3430 be connected to the network if it consists of only private IP addresses?
Yes, the Network Camera can be connected to a LAN with private IP addresses.
9. Can the DCS-3411/3430 be installed and work if a firewall exists on the network?
If a rewall exists on the network, port 80 is open for ordinary data communication. The DCS-3411/3430 uses
port 5002 for streaming audio and port 5003 for streaming video. These ports (or the ports you specify from the
Advanced Tab in the Conguration screen if you change the default ports) need to be opened on the rewall.
10. Why am I unable to access the DCS-3411/3430 from a Web browser?
If a router or rewall is used on the network, the correct ports for the DCS-3411/3430 may not be congured on
the router or rewall. To correct the problem, you need to determine if the DCS-3411/3430 is behind a router or
rewall and if the router or rewall is properly congured for the ports the DCS-3411/3430 is using. Other possible
problems might be due to the network cable. Try replacing your network cable. Test the network interface of the
product by connecting a local computer to the unit, utilizing a Ethernet crossover cable. If the problem is not solved
the Network Camera might be faulty.
11. Why does the Network Camera work locally but not externally?
This might be caused by network rewall protection. The rewall may need to have some settings changed in order
for the Network Camera to be accessible outside your local LAN. Check with the Network Administrator for your
network.
Make sure that the Network Camera isn’t conicting with any Web server you may have running on your network.
The default router setting might be a possible reason. Check that the conguration of the router settings allow the
Network Camera to be accessed outside your local LAN.
12. I connected the Network Camera directly to a computer with a cross-over cable Ethernet cable and
received the following Windows error upon running the Installation Wizard:
This Windows error will occur if the Network Camera is connected to a computer that is not properly congured with
a valid IP address. Turn o DHCP from the Network Settings in Windows and congure the computer with a valid IP
address, or connect the camera to a router with DHCP enabled. This error can also occur if the Installation Wizard
icon is clicked on more than once from the setup wizard.
65D-Link DCS-3411/3430 User Manual
Section 5 - Troubleshooting
13. Noisy images occur. How can I solve the problem?
The video images might be noisy if the Network Camera is used in a very low light environment.
To solve this issue you need more lighting.
13. The images appear to be of poor quality, how can I improve the image quality?
Make sure that your computer’s display properties are set above 256 colors. Using 16 or 256 colors on your
computer will produce dithering artifacts in the image, making the image appear to be of poor quality.
The conguration on the Network Camera image display is incorrect. Through the Advanced > Image Setting
section of the Web management you need to adjust the image related parameters such as brightness, contrast,
hue and power line frequency for uorescent light.
66D-Link DCS-3411/3430 User Manual
Section 6 - DI/DO
Reed switch
Vibration
sensor
RS485 Device
ALARM
DC Power 12V
Photo Relay
Photo Relay
Photo Relay
RS-485 Transceivers
0
0
0
0
0
IR illuminator
※DC12V total output current maximum to 200mA
DI/DO
67D-Link DCS-3411/3430 User Manual
Section 6 - DI/DO
12V+/12V-
DI
DO
485+/485-
Connect to an IR illuminator or other device in parallel connection.
The total output current should be under 200mA.
Receive signals from a motion detector or any other external
security device.
Connect to an alarm or buzzer. Refer to page 47.
Connect to the RS-485 interface for controlling auxiliary equipment
such as an external camera enclosure to perform PAN and TILT
movement. Refer to page 49 for more information.
68D-Link DCS-3411/3430 User Manual
Appendix A - Networking Basics
Networking Basics
Check your IP address
After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a
DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.
Click on Start > Run. In the run box type cmd and click OK.
At the prompt, type ipcong and press Enter.
This will display the IP address, subnet mask, and
the default gateway of your adapter.
If the address is 0.0.0.0, check your adapter
installation, security settings, and the settings
on your router. Some firewall software programs
may block a DHCP request on newly installed
adapters.
If you are connecting to a wireless network at a
hotspot (e.g. hotel, coee shop, airport), please contact an employee or administrator to verify their wireless network
settings.
69D-Link DCS-3411/3430 User Manual
Appendix A - Networking Basics
Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps
below:
Step 1
®
Windows
Windows® 2000 - From the desktop, right-click My Network Places > Properties.
Step 2
Right-click on the Local Area Connection which represents your D-Link network adapter and select Properties.
Step 3
Highlight Internet Protocol (TCP/IP) and click Properties.
Step 4
Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN
IP address on your router.
XP - Click on Start > Control Panel > Network Connections.
Example: If the camera´s LAN IP address is 192.168.0.1, make your IP address
192.168.0.X where X is a number between 2 and 99. Make sure that the number
you choose is not in use on the network. Set Default Gateway the same as the LAN
IP address of your router (192.168.0.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The
Secondary DNS is not needed or you may enter a DNS server from your ISP.
Step 5
Click OK twice to save your settings.
70D-Link DCS-3411/3430 User Manual
Appendix B - Technical Specifications
Technical Specifications
Video Codec
MPEG4 / MJPEG/ H.264 multi prole compression simultaneously
PoE (3411 only)
Supported IEEE 802.3af standard
Sensor
1/4” CMOS Sensor
SDRAM
64 Mbytes
Flash Memory
8 Mbytes
Lens
6mm, F1.8
Support Auto Iris lens, or IR lens
LAN
• 10/100Base T ports x1
• IEEE 802.3 compliance
• IEEE 802.3u compliance
• Support Full-Duplex operations
• MDI/MDIX auto-negotiation
• 802.3x Flow Control support for Full-Duplex mode
• Supported IEEE 802.3af standard (DCS-3411 only)
MIC
42dB +/- 3dB, Omni-directional
I/O Connector
2 Inputs (Photo relay, Active High: Dropout: 0 VDC)
1 Output (photo relay, Close circuit current: AC 70mA or DC 100mA;
40Ohm; Open circuit voltage: 240 VAC or 350VDC)
Power Output: 12VDC, 200mA
RS 485
2 pin(485A,485B) (Supported to control external Pan-Tilt device)
Audio Out
600mV
Video Out
75 ohm 1Vpp
Reset Button
Reset to factory default
Storage
SD card slot
Dimension (WxDxH)
177mm x 78mm x 60mm
Weight
577.8g
Max Power Consumption
• Max : DCS-3411 5.484 W, DCS-3430 6.9W
• Input: 100-240VAC, 50/60Hz, 0.4A
• Output: 12VDC, 1.25A
Antenna
2 (DCS-3430 only)
71D-Link DCS-3411/3430 User Manual
Appendix B - Technical Specifications
Wireless (DCS-3430 only)
Frequency RangeAnd Channels
• 2.412-2.4835 GHz
• 13 Channels (depend on Area)
Transmition
2TX, 2RX
Date Range
• IEEE 802.11n: From MCS0 to MCS15
• IEEE 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps
• IEEE 802.11b: 11, 5.5, 2, 1 Mbps
• Auto-select or Manual specied.
Outpower
• 12 dBm@11n (Typical)
• 12 dBm@11g (Typical)
• 16 dBm@11b (Typical)
Sensitivity
• HT40802.11n: Packet Error Rate < 10%, MCS6 < -60
dBm·
• HT20802.11n: Packet Error Rate < 10%, MCS6 < -66
dBm
• 802.11g: Packet Error Rate < 10%, 54Mbps < -66 dBm
• 802.11b: Packet Error Rate < 8%, 11Mbps < -82 dB
Antenna
• Connector: MHF
• Operating Frequency: 2.4Ghz
Networking
Protocol
• IPV4, ARP, TCP, UDP, ICMP
• DHCP Client
• NTP Client
• DNS Client
• DDNS Client (D-Link)
• SMTP Client
• FTP Client
• HTTP Server
• Samba Client
• PPPoE
• UPnP Port Forwarding
• RTP
• RTSP
• RTCP
• 3GPP
Ethernet
10/100M BaseT Fast Ethernet auto negotiation
Wireless (DCS-3430 only)
WMM
Video
Algorithm Supported
• MPEG4/MJPEG/H.264 multi prole compression
simultaneously
• JPEG for still image
Features
• Adjustable image size and quality
• Time stamp and text overlay
• Three congurative motion detection windows
• Flip & Mirror
Resolution
• Up to 30 frames at 640x480
• Up to 30 frames at 320x240
• Up to 30 frames at 160x120
Sensitivity
11.5 V/lux-s at 550nm
72D-Link DCS-3411/3430 User Manual
Appendix B - Technical Specifications
Video
AGC, AWB, AES, BLC
Digital Zoom
Up to 16X
Low Lux
0.5 lux@F1.8
3A control
AGC, AWB, AES
Electronic shutter
NTSC: 1/60 ~ 1/100000 sec.
PAL: 1/50 ~ 1/110000 sec.
Audio
Sample rate
GSM-AMR: 12.2kbps, ADPCM: 8Kbps
Cable
• Cable Length: 1800 ± 30mm
• UL 20AWGx2C (105°C) 300V
Microphone
Directional
Omni-directional
Frequency
20 ~ 20000Hz
S/N ratio
More than 58dB
LED
Control
Enable/Disable
Security
Login authentication
Default Admin ID/PW : admin/space(blank)
OS Support
Device
Windows 2000 / Windows XP / Windows Vista / 3GPP Mobile Phone
Utility
Windows 2000 / Windows XP / Windows Vista
Plug
• Type: L type
• Connector Color: Black
Frequency
20 ~ 20000Hz
S/N ratio
More than 58dB
Physical Environment
Power
• 12V 1.25A switching power adapter
• External AC-to-DC Switching Power Adapter
• Type: USA / UK / EUR / AUS / CN (Order by each territory)
Operation Temperature
0 to 40°C (32 to 104°F)
Storage Temperature
- 20 to 70°C (-4 to 158°F)
73D-Link DCS-3411/3430 User Manual
Appendix B - Technical Specifications
Humidity
20-80% RH non-condensing
Emission (EMI), Safety & Other Certifications
• FCC
• IC
• C-Tick
• CE
• LVD
1
Maximum wireless signal rate derived from IEEE Standard 802.11g, 802.11a and Draft 802.11n specications. Actual data throughput will vary. Network conditions and
environmental factors, including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely aect wireless signal range.
2
Range varies depending on country’s regulation.
3
The DCS-3411/3430 doesn’t include 5.25-5.35GHz & 5.47~5.725GHz.
74D-Link DCS-3411/3430 User Manual
Loading...