Denon DVD-2200 Instruction Manual

DVD AUDIO-VIDEO/SUPER AUDIO CD PLAYER

DVD

2200

OPERATING INSTRUCTIONS MODE D’EMPLOI INSTRUCCIONES DE OPERACION

ENTER

456

TOP MENU DISPLAY

MARKERRANDOM

PAGE

A-B

ZOOM

DIMMER PIC.ADJ

REPEAT

SETUP

NTSC / PAL

CALL RETURN

SKIP SLOW / SEARCH

POWER

ANGLE SUBTITLE AUDIO

SEARCH MODE

PLAY

STILL / PAUSE

STOP

PROG / DIR

CLEAR

SRS.TS

OPEN / CLOSE

RC-962

ON OFF

T. MENU

DISP.

FOR ENGLISH READERS PAGE 006 ~ PAGE 064 POUR LES LECTEURS FRANCAIS PAGE 065 ~ PAGE 123 PARA LECTORES DE ESPAÑOL PAGINA 124 ~ PAGINA 182

IMPORTANT TO SAFETY

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

1. Handle the power supply cord carefully

Do not damage or deform the power supply cord. If it is damaged or deformed, it may cause electric shock or malfunction when used. When removing from wall outlet, be sure to remove by holding the plug attachment and not by pulling the cord.

2. Do not open the top cover

In order to prevent electric shock, do not open the top cover. If problems occur, contact your DENON DEALER.

3. Do not place anything inside

Do not place metal objects or spill liquid inside the DVD audio-video/ Super audio CD player. Electric shock or malfunction may result.

Please, record and retain the Model name and serial number of your set shown on the rating label. Model No. DVD-2200 Serial No.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

NOTE:

This DVD audio-video/Super audio CD player uses the semiconductor laser. To allow you to enjoy music at a stable operation, it is recommended to use this in a room of 5 °C (41 °F) ~ 35 °C (95 °F).

CAUTION:

USE OF CONTROLS OR ADJUSTMENTS OR REFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

• FOR CANADA MODEL ONLY

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• POUR LES MODELE CANADIENS UNIQUEMENT

ATTENTION

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU FOND.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ENGLISH FRANCAIS ESPAÑOL

FRONT PANEL PANNEAU AVANT PANEL FRONTAL

REAR PANEL PANNEAU ARRIERE PANEL TRASERO

@2@1 @3

@7 @8

@5 @6

qw r

y u i o !0 !1e

!8 !3!5

!4 !2!7

SAFETY INSTRUCTIONS

1. Read Instructions – All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions – The safety and operating instructions should be retained for future reference.

3. Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions should be followed.

5. Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

6. Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10. Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Grounding or Polarization – This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

13. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

15. Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A.

16. Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

17. Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

18. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

19. Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

20.

Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

21.

Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service

personnel under the following conditions: a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the

product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation, e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance

– this indicates a need for service.

22. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

23. Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

24. Wall or Ceiling Mounting – The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

25. Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE ANTENNA

LEAD IN WIRE

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

ENGLISHFRANCAISESPAÑOL

NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION / NOTAS SOBRE EL USO

Copyrights / Droits d’auteur / Derechos de Autor

• Avoid high temperatures. Allow for sufficient heat dispersion when installed on a rack.

• Eviter des températures élevées. Tenir compte d’une dispersion de chaleur suffisante lors de l’installation sur une étagère.

• Evite altas temperaturas. Permite la suficiente dispersión del calor cuando está instalado en la consola.

• Keep the set free from moisture, water, and dust.

• Protéger l’appareil contre l’humidité, l’eau et lapoussière.

• Mantenga el equipo libre de humedad, agua y polvo.

• Do not let foreign objects in the set.

• Ne pas laisser des objets étrangers dans l’appareil.

• No deje objetos extraños dentro del equipo.

• Do not let insecticides, benzene, and thinner come in contact with the set.

• Ne pas mettre en contact des insecticides, du benzène et un diluant avec l’appareil.

• No permita el contacto de insecticidas, gasolina y diluyentes con el equipo.

• Unplug the power cord when not using the set for long periods of time.

• Débrancher le cordon d’alimentation lorsque l’appareil n’est pas utilisé pendant de longues périodes.

• Desconecte el cordón de energía cuando no utilice el equipo por mucho tiempo.

• Do not obstruct the ventilation holes.

• Ne pas obstruer les trous d’aération.

• No obstruya los orificios de ventilación.

• Never disassemble or modify the set in any way.

• Ne jamais démonter ou modifier l’appareil d’une manière ou d’une autre.

• Nunca desarme o modifique el equipo de ninguna manera.

✽ (For sets with ventilation holes)

It is prohibited by law to reproduce, broadcast, rent or play discs in public without the consent of the copyright holder.

La reproduction, la diffusion, la location, le prêt ou la lecture publique de ces disques sont interdits sans le consentement du détenteur des droits d’auteur.

De acuerdo con las leyes está prohibido reproducir, emitir, alquilar o interpretar discos en público sin la autorización del propietario de los derechos de autor.

• Handle the power cord carefully. Hold the plug when unplugging the cord.

• Manipuler le cordon d’alimentation avec précaution. Tenir la prise lors du débranchement du cordon.

• Maneje el cordón de energía con cuidado. Sostenga el enchufe cuando desconecte el cordón de energía.

ENGLISH

— TABLE OF CONTENTS —

Features...................................................................................6, 7

Discs ............................................................................................8

Cautions on Handling Discs.........................................................9

Connections ......................................................................10 ~ 15

Part Names and Functions ..................................................16, 17

Remote Control Unit............................................................18, 19

Loading Discs ............................................................................20

Changing the Default Settings..........................................21 ~ 37

Playback ............................................................................38 ~ 42

⁄0

Adjusting the Picture Quality ............................................43 ~ 45

⁄1

Using the On-Screen Display.....................................................46

⁄2

Playing Repeatedly ..............................................................47, 48

• ACCESSORIES

Please check to make sure the following items are included with the main unit in the carton:

q Audio video cord.......................................................................1

w Remote control unit (RC-962)...................................................1

e R6P/AA batteries......................................................................2

r Power supply cord....................................................................1

t Operating instructions..............................................................1

y Service station list ....................................................................1

FEATURES

1. Super Audio CD multi-channel playback compatibility

In addition to playing DVD audio and video discs, the DVD2200 can play multi-channel Super Audio CDs with a playback frequency range covering 100 kHz and a dynamic range of 120 dB or greater within the audible frequency range, and a maximum of 5.1 channels can be output.

2. High precision 24-bit D/A converter

The audio playback circuit includes an advanced segment type D/A converter with the top technical specifications in the business, manufactured by Burr-Brown, a company with an established reputation for D/A converters. This high performance D/A converter allows not only input of the 24bit/192 kHz data of DVD-Audio discs, it also includes an analog pure FIR filter for ideal DSD playback of Super Audio CDs. Furthermore, the same DAC is used unsparingly for the surround, center and LFE channels to provide optimum sound quality during multi-channel playback as well.

3. Dolby Digital (AC-3)/DTS decoder (NOTE 2)

The DVD-2200 is equipped with a built-in Dolby Digital (AC-3) /DTS decoder, allowing you to recreate the atmosphere of a movie theater or concert hall when using the DVD-2200 in combination with an AV amplifier and speakers.

4. Progressive Scan circuit “Pure Progressive

” (NOTE 3)

The DVD-2200 is equipped with a high precision Progressive Scan circuit “Pure Progressive

” allowing it to reproduce movies and other images on DVDs with a quality near that of the original.

5. 12-bit/108 MHz video D/A converter (NOTE 4)

The DVD-2200 uses a video D/A converter that conducts D/A conversion of all video signals at 12 bits and allows 4X oversampling in the progressive mode to achieve the high quality picture that DVDs are meant to provide. In addition, NSV technology reduces noise upon D/A conversion.

qwer

⁄3

Playing Tracks in the Desired Order ..........................................49

⁄4

Playing Tracks in the Random Order .........................................50

⁄5

MP3 Playback ......................................................................51, 52

⁄6

Playing Still Picture Files (JPEG format)............................53 ~ 55

⁄7

Using the Multiple Audio, Subtitle and Angle Functions

.......56 ~ 58

⁄8

Using the Menus.................................................................59, 60

⁄9

Marking Scenes you want to see again ....................................61

¤0

Playing in the Zoom Mode ........................................................62

¤1

Troubleshooting .........................................................................63

¤2

Main Specifications....................................................................64

ENGLISH

6. Anti-interference design through isolation of blocks

The DVD-2200 uses a 5-block architecture with the different functions (power supply, video circuitry, audio circuitry, etc.) on separate circuit boards to minimize mutual interference.

7. Thorough vibration-resistant design

The pickup mechanism is positioned at the center to reduce the effects of external vibrations.

8. Multiple functions

(1) Picture CD playback function (NOTE 5)

Kodak Picture CDs and Fujifilm Fujicolor CD can be played on the DVD-2200. Still images stored in JPEG format on CD-R/RWs can also be played.

(2) Multiple audio function

Selection of up to 8 audio languages. (The number of languages offered differs from DVD to DVD.)

(3) Multiple subtitle function

Selection of up to 32 subtitle languages. (The number of languages offered differs from DVD to DVD.)

(4) Multiple angle function

The angle of view can be changed. (For DVDs on which multiple angles are recorded.)

(5) GUI (Graphical User Interface) function

The DISPLAY button on the remote control unit can be used to display player and disc information on the TV screen.

(6) Marker function

The positions of up to five scenes can be stored in the memory, so you can watch your favorite scenes whenever you want.

(7) Playback disable function

This function can be used to disable playback of DVDs you do not want children to watch.

NOTES:

1. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Work. ©1992 – 1998 Dolby Laboratories, Inc. All rights reserved.

2. “DTS” and ”DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc.

3. “Pure Progressive” is a trademark of Silicon Image, Inc.

4. “NSV” is a trademark of Analog Devices, Inc.

5. “KODAK” is a trademark of Eastman Kodak Company. “Fujicolor CD” is a trademark of FUJI PHOTO FILM CO., LTD..

ENGLISH

DISCS

• The types of discs listed on the table below can be used on the DVD-2200.

The marks are indicated on the disc labels or jackets.

Usable

discs

Mark (logo)

Recorded

signals

Disc size

DVD video DVD audio

(NOTE 1)

DVD-R DVD-RW (NOTE 2)

Digital audio +

digital video

(MPEG2)

12 cm

8 cm

12 cm

8 cm

12 cm

8 cm

Digital audio +

digital video

(MPEG1)

Digital audio

MP3

Digital picture

(JPEG)

Video CD (NOTE 1)

CD-R

CD-RW

(NOTE 3)

2 The following types of discs cannot be played on the

DVD-2200:

• DVDs with region numbers other than “1” or “ALL”

• DVD-ROM/RAMs

• CD-ROMs

• CVD/VSDs

• CDVs (Only the audio part can be played.)

• CD-Gs (Only the audio is output.)

• Photo CDs

NOTE 1: Some DVD audio, DVD video and video CD discs do not

operate as described in this manual due to the intentions of the discs’ producers.

NOTE 2: Playing DVD-R and DVD-RW discs

DVD-R and DVD-RW discs recorded in video format on a DVD recorder can be played on the DVD-2200. Discs that have not be finalized cannot be played. Depending on the disc’s recording status, the disc may not be accepted or may not be played normally (the picture or sound may be not be smooth, etc.).

NOTE 3: According to recording quality, some CD-R/RW cannot be

played.

• Titles and chapters (DVD-videos)

DVD-videos are divided into several large sections called “titles” and smaller sections called “chapters”. Numbers are allotted to these sections. These numbers are called “title numbers” and “chapter numbers”.

• Playback control (video CDs)

Video CDs including the words “playback control” on the disc or jacket are equipped with a function for displaying menus on the TV screen for selecting the desired position, displaying information, etc., in dialog fashion. In this manual, playing video CDs using such menus is referred to “menu playback”. Video CDs with playback control can be used on the DVD-

2200.

NOTE:

• This DVD player is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DVD player, this DVD player cannot play this disc. The Region number for this DVD player is 1.

• Tracks (Super audio CDs, video and music CDs)

Super audio CDs, video and music CDs are divided into sections called “tracks”. Numbers are allotted to these sections. These numbers are called “track numbers”.

For example:

Title 1

Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2

Title 2

Track 1 Track 2 Track 3 Track 4 Track 5

Recordable

ReWritable

2 Disc terminology

• Groups and tracks (DVD-audios)

DVD-audios are divided into several large sections called “groups” and smaller sections called “tracks”. Numbers are allotted to these sections. These numbers are called “group numbers” and “track numbers”.

For example:

Group 1

Track 1 Track 2 Track 3 Track 1 Track 2

Group 2

12 cmJPEGPicture CD

12 cmDigital audio

Super

audio CD

12 cmJPEG

Fujicolor

Stereo

Multi-

ENGLISH

CAUTIONS ON HANDLING DISCS

Discs

Only the discs including the marks shown on page 8 can be played on the DVD-2200. Note, however, that discs with special shapes (heart-shaped discs, hexagonal discs, etc.) cannot be played on the DVD-2200. Do not attempt to play such discs, as they may damage the player.

Cautions on Handling Discs

• Do not get fingerprints, grease or dirt on discs.

• Be especially careful not to scratch discs when removing them from their cases.

• Do not bend discs.

• Do not heat discs.

• Do not enlarge the center hole.

• Do not write on the labeled (printed) side with a ball-point pen or a pencil.

• Water droplets may form on the surface if the disc is moved suddenly from a cold place to a warm one. Do not use a hairdryer, etc., to dry the disc.

Cautions on Storing Discs

• Always eject discs after playing them.

• Keep discs in their cases to protect them from dust, scratches and warping.

• Do not put discs in the following places:

1. Places exposed to direct sunlight for long periods of time

2. Humid or dusty places

3. Places exposed to heat from heaters, etc.

Cautions on Loading Discs

• Only load one disc at a time. Loading one disc on top of another may result in damage or scratch the discs.

• Load 8 cm discs securely in the disc guide, without using an adapter. If the disc is not properly loaded, it may slip out of the guide and block the disc tray.

• Be careful not to let your fingers get caught when the disc tray is closing.

• Do not place anything but discs in the disc tray.

• Do not load cracked or warped discs or discs that have been fixed with adhesive, etc.

• Do not use discs on which the adhesive part of cellophane tape or glue used to attach the label is exposed, or discs with traces of tape or labels that have been peeled off. Such discs may get stuck inside the player, resulting in damage.

Holding Discs

Avoid touching the surface of discs when loading and unloading them.

Cleaning Discs

Fingerprints or dirt on the disc may lower sound and picture quality or cause breaks in playback. Wipe off fingerprints or dirt.

Use a commercially available disc cleaning set or a soft cloth to wipe off fingerprints or dirt.

Be careful not to get fingerprints on the signal surface (the side which shines in rainbow colors).

Wipe gently from the middle outwards.

Do not wipe with a circular motion.

NOTE:

• Do not use record spray or antistatic. Also do not use volatile chemicals such as benzene or thinner.

Record

spray

Thinner Benzene

VIDEO IN S-VIDEO IN

AUDIO IN

ENGLISH

CONNECTIONS

• Read the manuals of all the components when making connections.

• Keep the power supply cord unplugged until all connections have been completed.

• If the power is on when connections are made, noise may be generated and damage the speakers.

• Be sure to connect the left and right channels properly, L (left) to L, R (right) to R.

• Plug the power supply cord securely into the power outlet. Incomplete connection may result in noise.

• Binding the power supply cord together with connection cords may result in humming or noise.

NOTES:

(1) Connecting to a TV

• Use the included audio video cord to connect the TV’s video input connector and audio input connectors to the DVD-2200’s VIDEO OUT or S-VIDEO OUT and AUDIO OUT.

DVD-2200

S-Video output connector

The video signals are divided into color (C) and brightness (Y) signals, achieving a clearer picture. If the TV is equipped with an S-Video input connector, we recommend connecting it to the DVD-2200’s S-Video output connector using a commercially available S-Video connection cord.

To power outlet

• Connect the DVD-2200’s video outputs to the TV either directly or through an AV amplifier. Do not connect it via a VCR (video cassette recorder). Some discs contain copy prohibit signals. If such discs are played via a VCR, the copy prohibit system may cause disturbance in the picture.

• Set the “TV TYPE” in “VIDEO SETUP” in “SETUP” to comply with your TV’s video format. When the TV is NTSC formated set to NTSC. (See page 28.)

• To use with 2-channel audio output, set “2 CHANNEL” in “AUDIO CHANNEL” in “AUDIO SETUP” in “SETUP” at the initial settings. (See page 30.)

• Set the “TV ASPECT” in “VIDEO SETUP” in “SETUP” to comply with your TV’s aspect. (See page 28)

NOTES:

ENGLISH

(2) Connecting to a TV or Monitor Equipped with Color Component Input Connectors

COMPONENT VIDEO IN

PR/CRPB/CBY

AUDIO IN

To power outlet

Color component output connectors (PR/CR, PB/CB and Y)

The red (PR/CR), blue (PB/CB) and brightness (Y) signals are output independently, achieving more faithful reproduction of the colors.

• The color component input connectors may be marked differently on some TVs or monitors (P

R, PB and Y/R-

Y, B-Y and Y/CR, CB and Y, etc.). For details, refer to the TV’s operating instructions.

• Connect in this way if your TV is compatible with Progressive Scan.

NOTES:

• Use the three commercially available video cords to connect the DVD-2200’s color component output connectors to the TV or monitor.

• Set the “TV TYPE” in “VIDEO SETUP” in “SETUP” to comply with your TV’s video format. When the TV is NTSC formated set to NTSC. (See page 28.)

• Set the “VIDEO OUT” in “VIDEO SETUP” in “SETUP” to comply with Progressive TV. (NTSC formated only)

• To use with 2-channel audio output, set “2 CHANNEL” in “AUDIO CHANNEL” in “AUDIO SETUP” in “SETUP” at the initial settings. (See page 30.)

• Set the “TV ASPECT” in “VIDEO SETUP” in “SETUP” to comply with your TV’s aspect. (See page 28.)

CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE “STANDARD DEFINITION” OUTPUT.

DVD-2200

If necessary, connect the video terminals, referring to page 10.

ENGLISH

NOTES:

• Harsh noise that could harm your ears or damage the speakers is generated when a DVD recorded in DTS is played while using a decoder, etc., that is not DTS-compatible.

• When playing copyright-protected linear PCM or packed PCM DVDs, in consideration of copyrights, no digital signals are output for sources exceeding 48 kHz/16 bits. When playing such sources, either set “LPCM (44.1 kHz/48 kHz)” under “AUDIO SETUP” at “SETUP” to “ON” (see page 33) or make analog connections. (See page 14.)

• When making digital connections to an AV amplifier that is not compatible with 96 kHz/88.2 kHz signals, set “LPCM (44.1 kHz/48 kHz)” under “AUDIO SETUP” at “SETUP” to “ON”. (See page 33.)

• With Super audio CDs, digital audio signals cannot be output. Use analog connections. (See page 14, 15.)

PHONES

DIRECT STEREO

ANALOG EXT. IN

DOLBY

SURROUND

DTS

SURROUND

WIDE

SCREEN

CINEMA / MUSIC

6.1 / 7.1 SURROUND

VIDEO ON / OFF

STATUS

M-ZONE 1

FUNCTION CONTROL

INPUT MODE

5CH / 7CH STEREO

DSP

SIMULATION

TONE

DEFEAT

MODE SELECT

REC /

M-ZONE 2

SURROUND MODE

INPUT REC SELECT / M-ZONE

MULTI FUNCTION

(3) Connecting to a AV amplifier with a built-in decoder

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital or DTS bitstream signals are output from the DVD player’s digital audio output connectors. If a Dolby Digital or DTS decoder is connected, you can achieve sound with the power and sense of presence of a movie theater or concert hall.

DVD-2200

Digital audio input connector (OPTICAL)

Front speaker (left)

Surround speaker (left)

Center speaker

Digital audio input connector (COAXIAL)

AV amplifier with a built-in decoder

(AV control center)

Front speaker (right)

Subwoofer

Surround speaker (right)

To power outlet

Optical fiber cable (commercially available)

75Ω/ohms pin-plug cable (commercially available)

The same data is output from both digital audio output connectors (COAXIAL and OPTICAL). Connect to one or the other connector, according to your system.

ENGLISH

2 Sound output from the DVD-2200’s digital audio output connectors

In the case of bit stream output

*1 Only 48 kHz/16 bit sources are output. *2 Only 44.1 kHz/16 bit sources are output. *3 44.1 kHz/16-bit PCM signals are output during CD layer playback.

• Down-mixed to 2 channels for multi-channel PCM sources. (Only the front left and right channels are output for sources for which downmixing is prohibited.)

• When “OFF” is selected, digital signals are not output from the digital audio output at this time.

• Linear PCM audio is the signal recording format used for music CDs. While the signals are recorded at 44.1 kHz/16 bit for music CDs, for DVDs they are recorded at 44.1 kHz/16 bit to 192 kHz/24 bit, providing higher sound quality than music CDs.

• Packed PCM signals are high sound quality compressed PCM signals that are decompressed with virtually no loss of data.

OFF

DVD audio

Audio recording format

Linear PCM

Video CD

Linear PCM

Packed PCM

Music CD

MP3 CD

44.1 kHz / 16 bit PCM

192 kHz / 16 ~ 24 bit

176.4 kHz / 16 ~ 24 bit

MPEG 1

44.1 kHz / 16 bit Linear PCM

MP3 (MPEG-1 Audio Layer 3)

96 kHz / 16 ~ 24 bit

88.2 kHz / 16 ~ 24 bit

48 kHz / 16 ~ 24 bit

44.1 kHz / 16 ~ 24 bit

96 kHz / 16 ~ 24 bit

48 kHz / 16 ~ 24 bit

LPCM SELECT

48 kHz / 16 bit PCM

44.1 kHz / 16 bit PCM

48 kHz / 16 bit PCM

44.1 kHz / 16 bit PCM

48 kHz / 16 bit PCM

44.1 kHz / 16 bit PCM

48 kHz / 16 bit PCM

DVD video

44.1 kHz / 16 bit PCM

No output data

No output data (*1)

No output data (*2)

No output data

No output data (*1)

44.1 kHz, 48 kHz / 16 bit PCM

Copy protection ON

88.2 kHz / 16 ~ 24 bit PCM

96 kHz / 16 ~ 24 bit PCM

88.2 kHz / 16 ~ 24 bit PCM

48 kHz / 16 ~ 24 bit PCM

96 kHz / 16 ~ 24 bit PCM

Copy protection OFF

44.1, 48 kHz / 16 bit PCM

Settings

NORMAL

Audio recording format

Dolby Digital

DTS

DIGITAL OUT

2 channels PCM

(48 kHz / 16 bit)

2 channels PCM

(48 kHz / 16 bit)

PCM

DVD video

Dolby Digital bitstream

DTS bitstream

Settings

In the case of PCM output

48 kHz / 16 ~ 24 bit PCM

44.1 kHz / 16 ~ 24 bit PCM

96 kHz / 16 ~ 24 bit PCM

Super audio CD

DSD (DIRECT STREAM DIGITAL) No output data (*3) No output data (*3)

ENGLISH

PHONES

DIRECT STEREO

ANALOG EXT. IN

DOLBY

SURROUND

DTS

SURROUND

WIDE SCREEN

CINEMA /

MUSIC

6.1 / 7.1

SURROUND

VIDEO ON / OFF

STATUS

M-ZONE 1

FUNCTION CONTROL

INPUT MODE

5CH / 7CH STEREO

DSP

SIMULATION

TONE

DEFEAT

MODE SELECT

REC /

M-ZONE 2

SURROUND MODE

INPUT REC SELECT / M-ZONE

MULTI FUNCTION

(4) Connecting a basic 5.1-channel surround system

Analog 5.1-channel audio signals can be output from the DVD-2200. The multichannel audio signals recorded in packed PCM and the multichannnel Super audio CDs can be played when an AV amplifier equipped with analog 5.1-channel audio inputs is connected.

DVD-2200

Front speaker (left)

Surround speaker (left)

Center speaker

AV amplifier with 5.1-channel inpur terminals

Front speaker (right)

Subwoofer

Surround speaker (right)

To power outlet

CENTER

SURROUND

SUBWOOFER

FRONT

NOTES:

• For multi-channel connections, set “AUDIO CHANNEL” under “AUDIO SETUP” at “SETUP” to “MULTI CHANNEL” and make the “SPEAKER CONFIGURATION”, “CHANNEL LEVEL” and “DELAY TIME” settings.

• The delay time setting is not valid when playing Super audio CDs.

• Set the “SUPER AUDIO CD” setting under “AUDIO SETUP” to “MULTI”.

• With the DVD-2200, we recommend turning the digital output off and only outputting analog signals in order to keep interference from the digital output circuitry to the minimum and allow you to enjoy high bit, high sampling frequency, high quality multi-channel sound.

If necessary, connect the video terminals, referring to page 10.

✽ Set the “AUDIO SETUP” default setting as shown below. (See page 33.)

• “DIGITAL OUT” → “PCM” “LPCM (44.1kHz/48kHz)” → “ON”

Playing DVDs with incorrect settings may result noise that could damage your ears or the speakers.

ENGLISH

(5) Connecting to a Digital Recorder (MD Recorder, DAT Deck, etc.)

Optical fiber cable (commercially available)

75Ω/ohms pin-plug cable (commercially available)

DVD-2200

(6) Connecting to a Stereo Component

DVD-2200

Stereo component

NOTE:

• When connecting to a 2-channel audio stereo device, set “AUDIO CHANNEL” under “AUDIO SETUP” at “SETUP” to “2 CHANNEL” (see page 30). For multi-channel sources, the signals are down-mixed into two channels (analog). (Only the front left and right channels are output for sources for which down-mixing is prohibited.)

Digital audio

input connector

(COAXIAL)

Digital audio

input connector

(OPTICAL)

NOTE:

• Digital audio signals cannot be output when playing Super Audio CDs. Use analog connections to record Super Audio CDs.

If necessary, connect the video terminals, referring to page 10.

ENGLISH

PART NAMES AND FUNCTIONS

(1) Front Panel

See page 3.

Power button

• Press once to turn the power on.

• Press again to set to the “OFF” position and turn the power

off.

• Set the power to the standby mode by pressing the POWER

OFF button on the remote control unit while the power is on.

• Turn the power on from the standby mode by pressing the

POWER ON button on the remote control unit.

Power indicator

• This indicator lights when the power is on and when the

power is in the standby mode.

Disc tray

• Load discs here. (See page 20.)

• Press the OPEN/CLOSE button !8 to open and close the

disc tray.

• The disc tray is also closed when the PLAY button

r is

pressed.

PLAY button (1)

• Press this button to play the disc. (See page 38.)

SEARCH MODE button

•

Press this to change the search mode to search for groups or titles, tracks or chapters when selecting sections of discs directly using the number buttons or SKIP buttons.

STILL/PAUSE button (3)

• Press this button to pause images or music or to play

images frame by frame. (See pages 40, 41.)

STOP button (2)

• Press this to stop the disc. (See page 40.)

Skip button (8)

• Press this to move back to the beginning of the current track

(or chapter).

• Press again to move back to the beginning of the previous

track (or chapter). (See page 41.)

Skip button (9)

• Press this to move ahead to the beginning of the next track

(or chapter). (See page 41.)

Slow/Search button (6)

• Press this to set the slow play mode and to search in the reverse direction. (See pages 40, 41.)

Slow/Search button (7)

• Press this to set the slow play mode and to search in the forward direction. (See pages 40, 41.)

PROGRESSIVE button

• Press to switch the progressive video output mode between progressive and interlace. (See psge 28.)

✽ This function does not work when a CD is playing.

PURE DIRECT VIDEO button

• Press to switch the video output between on and off.

• When the power is turned off, the setting is restored to the default value. (The default value is ON.)

SRS TS button

•

Sets the virtual surround sound. (Functions when playing DVD-videos or VCDs only. See page 42.)

PURE DIRECT DIGITAL button

• Press to switch the audio output between on and off.

• When the power is turned off, the setting is restored to the default value. (The default value is ON.)

PURE DIRECT DISPLAY button

• Press to switch the indicate in Display of the main unit between on and off.

• When the power is turned off, the setting is restored to the default value. (The default value is ON.)

• Even when the display is turned off, it lights for about 2 seconds when any button other than the DIMMER button is pressed.

Setting the playback area/layer of Super audio CD (SUPER AUDIO CD SETUP)

• Switch the area/layer of the Super audio CDs played with priority.

OPEN/CLOSE button (5)

• Press this button to open and close the disc tray. (See page 20.)

Display

• Information on the disc that is currently playing is shown on the display. (See page 17.)

Remote control sensor

ENGLISH

(2) Rear Panel

Component video output connectors (COMPONENT VIDEO OUT)

• Connect using video cords (available in stores).

Video output connector (VIDEO OUT)

• Connect using the included audio video cord.

S-Video output connector (S-VIDEO OUT)

• Connect using an S-Video connection cord (available in stores).

Audio output connectors (AUDIO OUT)

• Connect using the included audio video cord.

Digital audio output connector (COAXIAL)

• Connect using an digital audio cord. Connect a commercially available 75 Ω/ohms pin-plug cord.

• Digital data is output from this connector.

Digital audio output connector (OPTICAL)

• Connect using an optical fiber cable (available in stores).

• Digital data is output from this connector.

(3) Display

Lights during playback, flashes when the resume play memory function is activated.

Lights in the repeat play mode.

Lights in the still/pause mode.

Displays the title, track number and elapsed time during playback.

Lights to indicate the currently playing video type. F: Film source V: Video source G: Graphic source

Lights in the programmed play mode.

Lights during playback of multiple angles disc.

Lights when the audio signals can be down-mixed.

Control output connector (ROOM TO ROOM/OUT)

• This is the output connector for wired remote control. Consult your DENON dealer if you wish to use this connector.

Control input connector (ROOM TO ROOM/IN)

• This is the input connector for wired remote control. Consult your DENON dealer if you wish to use this connector.

Power input (AC IN)

• Connect to AC power supply using the included power supply cord.

Lights to indicate the currently playing disc.

Lights when progressive video signals are being output.

Lights in the random play mode.

Lights to indicate the currently playing audio channel. L: Front left channel C: Center channel R: Front right channel SL: Surround left channel S: Mono surround channel SR: Surround right channnel LFE: Low frequency effect

Lights to indicate the currently playing audio format.

These light to indicate the names of the sections of the disc being played.

These light to indicate the time display mode.

Lights when SRS TruSurround is on.

ENGLISH

REMOTE CONTROL UNIT

2 The DVD-2200 can be controlled from a distance using the included remote control unit (RC-962).

(1) Inserting Batteries

q Remove the remote control unit’s rear cover.

w Place two R6P/AA batteries in the battery compartment in the

direction indicated by the marks.

e Close the rear cover.

Cautions On Batteries

• Use R6P/AA batteries in this remote control unit.

• Replace the batteries with new ones approximately once a year, though this depends on the frequency with which the remote control unit is used.

• If the remote control unit does not operate from close to the main unit, replace the batteries with new ones, even if less than a year has passed.

• The included battery is only for verifying operation. Replace it with a new battery as soon as possible.

• When inserting the batteries, be careful to do so in the proper direction, following the < and > marks in the remote control unit’s battery compartment.

• To prevent damage or battery fluid leakage:

• Do not use a new battery with an old one.

• Do not use two different types of batteries.

• Do not short-circuit, disassemble, heat or dispose of

batteries in flames.

• Remove the batteries when not planning to use the remote control unit for a long period of time.

• If the batteries should leak, carefully wipe off the fluid from the inside of the battery compartment, then insert new batteries.

(2) Using the Remote Control Unit

30°

Approx. 7 meters

• When operating the remote control unit, point it at the remote control sensor as shown on the diagram.

• The remote control unit can be used from a direct distance of approximately 7 meters. This distance will be shorter, however, if there are obstacles in the way or if the remote control unit is not pointed directly at the remote control sensor.

• The remote control unit can be operated at a horizontal angle of up to 30° with respect to the remote control sensor.

NOTES:

• It may be difficult to operate the remote control unit if the remote control sensor is exposed to direct sunlight or strong artificial light.

• Do not press buttons on the main unit and on the remote control unit at the same time. Doing so will result in malfunction.

ENGLISH

(3) Names and Functions of Remote Control Unit Buttons

A-B repeat button (A-B)

Use this to repeat sections between two specific points.

REPEAT button

Press this to play tracks repeatedly.

Number buttons

Use these to input numbers. Use the +10 button to input numbers of 10 or over. Example: To input 25

5+10 +10

Picture adjust button (PIC.ADJ)

Press this to adjust the picture quality to suit your tastes.

ENTER

456

TOP MENU DISPLAY

MARKERRANDOM

PAGE

A-B

ZOOM

DIMMER PIC.ADJ

REPEAT

SETUP

NTSC / PAL

CALL RETURN

SKIP SLOW / SEARCH

POWER

ANGLE SUBTITLE AUDIO

SEARCH MODE

PLAY

STILL / PAUSE

STOP

PROG / DIR

CLEAR

SRS.TS

OPEN / CLOSE

RC-962

ON OFF

T. MENU

DISP.

Cursor buttons/ENTER button

Use the • and ª cursor buttons to select in the vertical direction. Use the

and 1cursor buttons to select in the horizontal direction. Press the ENTER button to select the item selected with the cursor buttons.

SUBTITLE button

Press this to switch the DVD’s subtitle language.

DISPLAY button

Press this to display the ON-SCREEN.

STOP button (2)

SKIP buttons

POWER ON/POWER OFF buttons

Press this to switch the power between on and standby.

STILL/PAUSE button (3)

NTSC/PAL button

Use this to switch the set’s video output format (NTSC/PAL).

OPEN/CLOSE button

SLOW/SEARCH buttons

PLAY button (1)

ANGLE button

Press this to switch the angle.

AUDIO button

For DVDs, press this to switch the audio language. For video CDs, press this to switch the channel between “LR”, “L” and “R”.

TOP MENU button

MENU button

RETURN button

Press this to return to the previous menu screen.

ZOOM button

Press this to enlarge the image.

DIMMER button

Use this to adjust the brightness of the main unit’s display. Can be switched in 4 steps, from OFF to always on.

PROGRAM/DIRECT button (PROG/DIR)

Press this to switch between the normal play, programmed play.

CLEAR button

Press this to clear numbers that you have input.

CALL button

Press this to check the program contents.

MARKER button

Press this to mark places you want to see again.

SEARCH MODE button

Press this to change the search mode to search for groups or titles, tracks or chapters when selecting sections of discs directly using the number buttons or SKIP buttons.

SRS TS button

Sets the virtual surround sound. (Functions when playing DVD-videos or VCDs only. See page 42.)

RANDOM button

Press this to play the tracks on the video or music CD in random order.

PAGE -/PAGE + buttons

Use these to selected the desired still picture on DVD audio discs containing browseable still pictures.

SETUP button

Press this to display the default setting screen.

The top menu stored on the disc is displayed.

The DVD menu stored on the disc is displayed.

2 Button not explained here function in the same way as the corresponding buttons on the main unit.

ENGLISH

LOADING DISCS

2 Set discs in the disc tray with the labeled (printed) side facing up.

8 cm disc guide

Disc tray

NOTE:

• Do not move the DVD-2200 while a disc is playing. Doing so may scratch the disc.

(1) Opening and Closing the Disc Tray

q Turn on the power. w Press the OPEN/CLOSE button.

Disc tray

OPEN/CLOSE button

NOTES:

• Be sure to turn on the power before opening and closing the disc tray.

• Do not strike on the button with a pencil, etc.

(2) Loading Discs

• Pick up the disc carefully so as not to touch the signal surface and hold it with the labeled side facing up.

• With the disc tray fully open, set the disc in the disc tray.

• Set 12 cm discs in the outer tray guide (Figure 1), 8 cm discs in the inner tray guide (Figure 2).

• Press the OPEN/CLOSE button. The disc is automatically loaded.

• The disc tray can also be closed automatically to load the disc by pressing the PLAY button.

Figure 1

Outer disc tray

12 cm disc

Figure 2

Inner disc tray

8 cm disc

NOTES:

• If a foreign object is caught in the disc tray during closing, simply press the OPEN/CLOSE button again and the tray will open.

• Do not press the disc tray in by hand when the power is off. Doing so will damage it.

• Do not place foreign objects in the disc tray. Doing so will damage it.

12 cm disc guide

Power button

ENGLISH

In the stop mode, press the SETUP button.

• The setup (default settings) screen appears.

NOTE: For some menus, the initial values can be changed during playback. DISC SETUP

Use this to set the language to be used when playing the disc. If the set language is not offered on that disc, the discs default language is set.

OSD SETUP

Use this to set the language for the default setting screen and messages displayed on the TV screen (“PLAY”, etc.).

VIDEO SETUP

Use this to set the DVD-2200’s screen mode. (TV aspect and TV type.)

AUDIO SETUP

Use this to set the DVD-2200’s audio output mode. (Digital and LPCM output settings.)

RATINGS

Use this to disable playback of adult DVDs so that children cannot watch them. Note that playback of adult DVDs cannot be disabled if the rating level is not recorded on the DVD.

OTHER SETUP

These include special settings CAPTIONS and COMPRESSION.

Use the 0and 1cursor buttons to select the desired setting item, then press the ENTER button. Select “DISC SETUP”. (See page 23.) Select “OSD SETUP”. (See page 26.) Select “VIDEO SETUP”. (See page 27.) Select “AUDIO SETUP”. (See page 30.) Select “RATINGS”. (See page 34.) Select “OTHER SETUP”. (See page 36.)

D I SC SE TUP

SELECT: DECISION:ENTER BUTTON

D I ALOG

D I SC MENUS

EXI T SETUP

SUBT I T L E

ENGL ISH O FF ENGLISH

CHANGING THE DEFAULT SETTINGS

ENTER

456

TOP MENU DISPLAY

MARKERRANDOM

PAGE

A-B

ZOOM

DIMMER PIC.ADJ

REPEAT

SETUP

NTSC / PAL

CALL RETURN

SKIP SLOW / SEARCH

POWER

ANGLE SUBTITLE AUDIO

SEARCH MODE

PLAY

STILL / PAUSE

STOP

PROG / DIR

CLEAR

SRS.TS

OPEN / CLOSE

ON OFF

T. MENU

DISP.

SETUP

Remote control unit

ENTER

✽

To exit the setup mode

Use the ªcursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit by pressing the SETUP button on the remote control unit.

Turn on the power.

• Press the power button, the power indicator lights and the power turns on.

¢ON / STANDBY

£ OFF

Main unit Remote control unit

POWER

2 Make the initial settings to suit your usage conditions before starting playback.

The initial settings are retained until they are next changed, even if the power is turned off.

Remote control unit

Light

ENGLISH

DISC SETUP

DIALOG

SUBTITLE

DISC MENUS

ENGLISH

FRENCH SPANISH GERMAN JAPANESE OTHERS

OFF

ENGLISH FRENCH SPANISH GERMAN JAPANESE OTHERS

ENGLISH

FRENCH SPANISH GERMAN JAPANESE OTHERS

OSD SETUP

OSD LANGUAGE

WALL PAPER

ENGLISH

FRANÇAIS ESPAÑOL

BLUE

GRAY BLACK PICTURE

VIDEO SETUP

TV ASPECT

TV TYPE

VIDEO OUT

STILL MODE

BLACK LEVEL

PROGRESSIVE MODE

4:3 PS 4:3 LB

WIDE (16:9)

NTSC PAL

MULTI

PROGRESSIVE

INTERLACED

FIELD FRAME

AUTO

DARKER

LIGHTER

MODE 1

MODE 2

AUDIO SETUP

AUDIO CHANNEL

SUPER AUDIO CD

DIGITAL OUT

LPCM (44.1 kHz/48 kHz)

BASS ENHANCER (2 CHANNEL)

MULTI CHANNEL

2 CHANNEL

MULTI

STEREO CD

NORMAL

PCM

OFF

SPEAKER CONFIGURATION

CHANNEL LEVEL

DELAY TIME

FRONT SP

CENTER SP

SUBWOOFER

SURROUND SP

FILTER

TEST TONE

FRONT Lch CENTER FRONT Rch SURROUND Rch SURROUND Lch SUBWOOFER SW +10dB

DISTANCE

FRONT Lch FRONT Rch CENTER SURROUND Lch SURROUND Rch SUBWOOFER DEFAULT

LARGE

SMALL

LARGE

SMALL NONE

YES

LARGE

SMALL NONE

OFF

AUTO MANUAL 0 dB 0 dB 0 dB 0 dB 0 dB 0 dB

OFF

METERS

FEET

12 ft 12 ft 12 ft 10 ft 10 ft 12 ft ON

RATINGS

RATING LEVEL

PASSWORD

CHANGE

1 2 3 4 5 6 7 8

NO LIMIT

OLD PASSWORD NEW PASSWORD COMFIRM PASSWORD

OTHER SETUP

PLAYER MODE

CAPTIONS

COMPRESSION

AUTO POWER MODE

SLIDE SHOW

AUDIO

VIDEO

OFF

5 SEC

Setup items for use

Bold characters indicate factory defaults.

ENGLISH

When “DISC SETUP” is selected

See page 21.

Use the •and ªcursor buttons to select the desired setting, then press the ENTER button.

DIALOG

Use this to set the language of the sound output from the speakers.

SUBTITLE

Use this to set the language of the subtitles displayed on the TV.

DISC MENUS

Use this to set the language of the menus recorded on the disc (top menu, etc.).

Use the •and ªcursor buttons to select the desired setting, then press the ENTER button.

When “DIALOG” is selected:

ENGLISH (Factory default)

Select this when you want to play the DVD with the sound in English.

FRENCH

Select this when you want to play the DVD with the sound in French.

SPANISH

Select this when you want to play the DVD with the sound in Spanish.

GERMAN

Select this when you want to play the DVD with the sound in German.

JAPANESE

Select this when you want to play the DVD with the sound in Japanese.

OTHERS

Use the number buttons to input the language number. (See “Language code list” on page 25.)

D I SC SE TUP

SELECT: DECISION:ENTER BUTTON

D I ALOG

D I SC MENUS

EXI T SETUP

SUBT I T L E

ENGL ISH O FF ENGLISH

ENTER

456

TOP MENU DISPLAY

MARKERRANDOM

PAGE

A-B

ZOOM

DIMMER PIC.ADJ

REPEAT

SETUP

NTSC / PAL

CALL RETURN

SKIP SLOW / SEARCH

POWER

ANGLE SUBTITLE AUDIO

SEARCH MODE

PLAY

STILL / PAUSE

STOP

PROG / DIR

CLEAR

SRS.TS

OPEN / CLOSE

ON OFF

T. MENU

DISP.

1, 2, 3

D I SC SE TUP

SELECT: DECISION:ENTER BUTTON

DIAL OG

D I SC MENUS

EXI T SETUP

SUBT I T L E

ENGLISH

FRENCH

SPAN I SH

JAPANESE

GER MAN

OTHERS

Remote control unit

ENTER

Remote control unit

ENTER

Remote control unit

ENGLISH

When “SUBTITLE” is selected:

OFF (Factory default)

Select this if you do not want to display the subtitles. (For some discs it is not possible to turn off the subtitle display.)

ENGLISH

Select this when you want to play the DVD with the subtitles in English.

FRENCH

Select this when you want to play the DVD with the subtitles in French.

SPANISH

Select this when you want to play the DVD with the subtitles in Spanish.

GERMAN

Select this when you want to play the DVD with the subtitles in German.

JAPANESE

Select this when you want to play the DVD with the subtitles in Japanese.

OTHERS

Use the number buttons to input the language number. (See “Language code list” on page 25.)

When “DISC MENUS” is selected:

ENGLISH (Factory default)

Select this when you want to display the menus in English.

FRENCH

Select this when you want to display the menus in French.

SPANISH

Select this when you want to display the menus in Spanish.

GERMAN

Select this when you want to display the menus in German.

JAPANESE

Select this when you want to display the menus in Japanese.

OTHERS

Use the number buttons to input the language number. (See “Language code list” on page 25.)

D I SC SE TUP

SELECT: DECISION:ENTER BUTTON

D I ALOG

D I SC MENUS

EXI T SETUP

SUBT IT LE

ENGLISH

FRENCH

SPAN I SH

JAPANESE

GER MAN

OTHERS

OFF

D I SC SE TUP

SELECT: DECISION:ENTER BUTTON

D I ALOG

D I SC MENUS

EXI T SETUP

SUBT I T L E

ENGLISH

FRENCH

SPAN I SH

JAPANESE

GER MAN

OTHERS

✽

To exit the setup mode

Use the ªcursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit by pressing the SETUP button on the remote control unit.

ENGLISH

Language code list

Code

6565

6566

6570

6577

6582

6583

6588

6590

6665

6669

6671

6672

6678

6679

6682

6765

6779

6783

6789

6865

6869

6890

6976

6978

6979

6983

6984

6985

7065

7073

7074

Code

7079

7082

7089

7165

7168

7176

7178

7185

7265

7273

7282

7285

7289

7365

7378

7383

7384

7387

7465

7473

7487

7565

7575

7576

7577

7578

7579

7583

7585

7589

7665

Code

7678

7679

7684

7686

7771

7773

7775

7776

7778

7779

7782

7783

7784

7789

7865

7869

7876

7879

7982

8065

8076

8083

8084

8185

8277

8279

8285

8365

8368

8372

8373

Language

Afar

Abkhazian

Afrikaans

Ameharic

Arabic

Assamese

Aymara

Azerbaijani

Bashkir

Byelorussian

Bulgarian

Bihari

Bengali; Bangla

Tibetan

Breton

Catalan

Corsican

Czech

Welsh

Danish

German

Bhutani

Greek

English

Esperanto

Spanish

Estonian

Basque

Persian

Finnish

Fiji

Language

Faroese

French

Frisian

Irish

Scots Gaelic

Galician

Guarani

Gujarati

Hausa

Hindi

Croatian

Hungarian

Armenian

Interlingua

Indonesian

Icelandic

Italian

Hebrew

Japanese

Yiddish

Javanese

Georgian

Kazakh

Greenlandic

Cambodian

Kannada

Korean

Kashmiri

Kurdish

Kirghiz

Latin

Language

Lingala

Laothian

Lithuanian

Latvian, Lettish

Malagasy

Maori

Macedonish

Malayalam

Mongolian

Moldavian

Marathi

Malay

Maltese

Burmese

Nauru

Nepali

Dutch

Norwegian

Oriya

Panjabi

Polish

Pashto, Pushto

Portuguese

Quechua

Rhaeto-Romance

Romanian

Russian

Sanskrit

Sindhi

Serbo-Croatian

Singhalese

Code

8375

8376

8377

8378

8379

8381

8382

8385

8386

8387

8465

8469

8471

8472

8473

8475

8476

8479

8482

8484

8487

8575

8582

8590

8673

8679

8779

8872

8979

9072

9085

Language

Slovak

Slovenian

Samoan

Shona

Somali

Albanian

Serbian

Sundanese

Swedish

Swahili

Tamil

Telugu

Tajik

Thai

Tigrinya

Turkmen

Tagalog

Tonga

Turkish

Tatar

Twi

Ukrainian

Urdu

Uzbek

Vietnamese

Volapük

Wolof

Xhosa

Yoruba

Chinese

Zulu

ENGLISH

When “OSD SETUP” is selected

See page 21.

Use the •and ªcursor buttons to select the desired setting, then press the ENTER button.

OSD LANGUAGE

Use this to set the language for the default setting screen and messages displayed on the TV screen (“PLAY”, etc.)

WALL PAPER

Use this to select the image to be shown on the screen in the stop mode and CD play mode.

ENTER

456

TOP MENU DISPLAY

MARKERRANDOM

PAGE

A-B

ZOOM

DIMMER PIC.ADJ

REPEAT

SETUP

NTSC / PAL

CALL RETURN

SKIP SLOW / SEARCH

POWER

ANGLE SUBTITLE AUDIO

SEARCH MODE

PLAY

STILL / PAUSE

STOP

PROG / DIR

CLEAR

SRS.TS

OPEN / CLOSE

ON OFF

T. MENU

DISP.

1, 2, 3

OSD SE TUP

SELECT: DECISION:ENTER BUTTON

OSD L ANGUAGE

EXI T SETUP

AL L PA PER

ENGLISH

BUL E

Use the •and ªcursor buttons to select the desired setting, then press the ENTER button.

When “OSD LANGUAGE” is selected:

ENGLISH (Factory default)

Select this to set the OSD language to English.

FRANÇAIS

Select this to set the OSD language to French.

ESPAÑOL

Select this to set the OSD language to Spanish.

OSD SE TUP

SELECT: DECISION:ENTER BUTTON

OSD L ANGUAGE

EXI T SETUP

AL L PA PER

ENGLISH

FRANÇAIS

ESPAÑOL

Remote control unit

ENTER

Remote control unit

ENTER

Remote control unit

ENGLISH

When “WALL PAPER” is selected:

BLUE (Factory default)

Select this to display a blue background on the TV display.

GRAY

Select this to display a gray background on the TV display.

BLACK

Select this to display a black background on the TV display.

PICTURE

Select this to display the wallpaper on the TV display.

✽ To exit the setup mode

Use the ªcursor button to select “EXIT SETUP”, then press the ENTER button. It is also possible to quit by pressing the SETUP button on the remote control unit.

OSD SE TUP

SELECT: DECISION:ENTER BUTTON

OSD L ANGUAGE

EXI T SETUP

AL L PA PER

BUL E

GRAY

BL ACK

PICTURE

When “VIDEO SETUP” is selected

See page 21.

Use the •and ªcursor buttons to select the desired setting, then press the ENTER button.

TV ASPECT

Use this to set the shape of your TV’s screen.

TV TYPE

Use this to set your TV’s video format (NTSC, PAL or MULTI).

VIDEO OUT

Use this to select either the progressive image output or interlace image output.

STILL MODE

The play DVD video, select the desired video mode (“FIELD”, “FRAME”, “AUTO”).

BLACK LEVEL

To select the black level of the picture, “DARKER” or “LIGHTER”.

PROGRESSIVE MODE

Select the film source and video source detection method recorded on the DVD. Normally select “MODE 1” (level detection mode). (only valid for progressive output during DVD video playback)

ENTER

456

TOP MENU DISPLAY

MARKERRANDOM

PAGE

A-B

ZOOM

DIMMER PIC.ADJ

REPEAT

SETUP

NTSC / PAL

CALL RETURN

SKIP SLOW / SEARCH

POWER

ANGLE SUBTITLE AUDIO

SEARCH MODE

PLAY

STILL / PAUSE

STOP

PROG / DIR

CLEAR

SRS.TS

OPEN / CLOSE

ON OFF

T. MENU

DISP.

1, 2, 3

V IDEO SETUP

SELECT: DECISION:ENTER BUTTON

TV ASPECT TV TYPE V I DEO OUT ST I L L MODE

IDE(16:9)

MULTI

PROGRESS IVE

AUTO

BL ACK L EV EL

LIGHTER

PROGRE SS I VE MODE

MODE 1

EXI T SETUP

Remote control unit

ENTER

Remote control unit

+ 60 hidden pages