Page 1
STGB10NC60KD, STGD10NC60KD
STGF10NC60KD, STGP10NC60KD
10 A, 600 V short-circuit rugged IGBT
Features
■ Lower on voltage drop (V
■ Lower C
RES
/ C
ratio (no cross-conduction
IES
susceptibility)
■ Very soft ultra fast recovery antiparallel diode
■ Short-circuit withstand time 10µs
CE(sat)
)
Description
This IGBT utilizes the advanced PowerMESH™
process resulting in an excellent trade-off
between switching performance and low on-state
behavior.
Applications
■ High frequency motor controls
■ SMPS and PFC in both hard switch and
resonant topologies
■ Motor drives
TAB
3
1
2
D
PAK
TO-220FP
3
2
1
TAB
3
1
DPAK
TAB
1
TO-220
Figure 1. Internal schematic diagram
3
2
Table 1. Device summary
Order codes Marking Packages Packaging
STGB10NC60KDT4 GB10NC60KD D
STGD10NC60KDT4 GD10NC60KD DPAK
STGF10NC60KD GF10NC60KD TO-220FP
STGP10NC60KD GP10NC60KD TO-220
November 2009 Doc ID 11423 Rev 6 1/20
2
PA K
Tape and reel
Tu b e
www.st.com
20
Page 2
Contents STGx10NC60KD
Contents
1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2/20 Doc ID 11423 Rev 6
Page 3
STGx10NC60KD Electrical ratings
1 Electrical ratings
Table 2. Absolute maximum ratings
Val ue
Symbol Parameter
V
CES
I
C
I
C
I
CL
I
CP
V
I
I
FSM
P
TOT
V
ISO
t
scw
T
T
1. Calculated according to the iterative formula
Collector-emitter voltage (V
(1)
Continuous collector current at TC = 25°C
(1)
Continuous collector current at TC = 100°C
(2)
Turn-off latching current 30 A
(3)
Pulsed collector current 30 A
Gate-emitter voltage ±20 V
GE
Diode RMS forward current at Tc=25°C 10 A
F
GE
Surge non repetitive forward current Tp = 10 ms
sinusoidal
Total dissipation at TC = 25°C
Insulation withstand voltage (RMS) from all three
leads to external heat sink (t=1s;T
Short-circuit withstand time
= 0.5 V
V
CE
Storage temperature
stg
Operating junction temperature
j
, Tj = 125 °C, RG = 10 Ω, VGE = 12 V
CES
= 0)
=25°C)
C
D²PAK
TO-220
DPAK TO-220FP
600 V
20 9 A
10 6 A
20 A
65 62 25 W
-- 2500 V
10 µs
– 55 to 150 °C
Unit
ICTC()
2. Vclamp = 80 % V
3. Pulse width limited by maximum junction temperature and turn-off within RBSOA
, VGE = 15 V, RG = 10 Ω, TJ = 150 °C
CES
--------------------------------------------------------------------------------------------------------- -=
R
thj c–
T
V
CE sat()max()Tjmax()ICTC
–
jmax()TC
Doc ID 11423 Rev 6 3/20
(),()×
Page 4
Electrical ratings STGx10NC60KD
Table 3. Thermal data
Val ue
Symbol Parameter
R
thj-case
R
thj-case
R
thj-amb
Thermal resistance junction-case IGBT 1.9 2 5
Thermal resistance junction-case diode 4 4.5 7
Thermal resistance junction-ambient 62.5 100 62.5
TO-220
D²PAK
Unit
DPAK TO-220FP
°C/W
4/20 Doc ID 11423 Rev 6
Page 5
STGx10NC60KD Electrical characteristics
2 Electrical characteristics
(Tj =25°C unless otherwise specified)
Table 4. Static
Symbol Parameter Test conditions Min. Typ. Max. Unit
Collector-emitter
V
(BR)CES
V
CE(sat)
V
GE(th)
I
CES
I
GES
g
1. Pulse test: pulse duration < 300 µs, duty cycle < 2 %
breakdown voltage
(VGE= 0)
Collector-emitter saturation
voltage
Gate threshold voltage
Collector cut-off current
= 0)
(V
GE
Gate-emitter leakage
current (V
(1)
Forward transconductance
fs
CE
= 0)
IC= 1mA
= 15V, IC= 5A
V
GE
= 15V, IC= 5A, Tj= 125°C
V
GE
= VGE, IC= 250µA
V
CE
VCE= 600 V
=600 V, Tj = 125°C
V
CE
VGE= ±20V
V
= 15V, IC= 5A
CE
600 V
2.2
2.5 V
1.8
4.5 6.5 V
1501µA
mA
±100 nA
15 S
V
Table 5. Dynamic
Symbol Parameter Test conditions Min. Typ. Max. Unit
C
C
C
Q
Q
Q
Input capacitance
ies
Output capacitance
oes
Reverse transfer
res
capacitance
g
Total gate charge
Gate-emitter charge
ge
Gate-collector charge
gc
= 25V, f = 1MHz,
V
CE
= 0
V
GE
= 390V, IC = 5A,
V
CE
= 15V,
V
GE
(see Figure 19)
380
-
46
-
8.5
19
-
5
-
9
pF
pF
pF
nC
nC
nC
Doc ID 11423 Rev 6 5/20
Page 6
Electrical characteristics STGx10NC60KD
Table 6. Switching on/off (inductive load)
Symbol Parameter Test conditions Min. Typ. Max. Unit
t
d(on)
t
(di/dt)
t
d(on)
t
(di/dt)
tr(V
t
d(off
t
tr(V
t
d(off
t
Turn-on delay time
Current rise time
r
Turn-on current slope
on
Turn-on delay time
Current rise time
r
Turn-on current slope
on
)
off
Off voltage rise time
)
Turn-off delay time
Current fall time
f
)
off
Off voltage rise time
)
Turn-off delay time
Current fall time
f
= 390V, IC = 5A
V
CC
R
= 10Ω, VGE= 15V
G
(see Figure 20)
= 390V, IC = 5A
V
CC
= 10Ω, VGE= 15V,
R
G
=125°C
T
j
(see Figure 20)
Vcc = 390V, IC = 5A,
= 10Ω, VGE = 15V
R
GE
(see Figure 20)
= 390V, IC = 5A,
V
cc
=10Ω, VGE =15V,
R
GE
=125°C
T
j
(see Figure 20)
17
-
6
-
655
16.5
-
6.5
-
575
33
-
72
-
82
60
-
106
-
136
Table 7. Switching energy (inductive load)
Symbol Parameter Test conditions Min. Typ. Max. Unit
(1)
E
on
E
off
E
E
on
E
off
E
1. Eon is the tun-on losses when a typical diode is used in the test circuit in figure 2. If the IGBT is offered in
a package with a co-pak diode, the co-pack diode is used as external diode. IGBTs & Diode are at the
same temperature (25°C and 125°C)
2. Turn-off losses include also the tail of the collector current
Turn-on switching losses
(2)
Turn-off switching losses
Total switching losses
ts
(1)
Turn-on switching losses
(2)
Turn-off switching losses
Total switching losses
ts
= 390V, IC = 5A
V
CC
=10Ω, VGE=15V
R
G
(see Figure 20)
VCC = 390V, IC = 5A
R
=10Ω, VGE= 15V,
G
= 125°C
T
j
(see Figure 20)
55
-
85
-
140
87
-
162
-
249
ns
ns
A/µs
ns
ns
A/µs
ns
ns
ns
ns
ns
ns
µJ
µJ
µJ
µJ
µJ
µJ
6/20 Doc ID 11423 Rev 6
Page 7
STGx10NC60KD Electrical characteristics
Table 8. Collector-emitter diode
Symbol Parameter Test conditions Min Typ. Max. Unit
I
I
V
t
Q
rrm
t
Q
rrm
Forward on-voltage
F
Reverse recovery time
rr
Reverse recovery charge
rr
Reverse recovery current
Reverse recovery time
rr
Reverse recovery charge
rr
Reverse recovery current
IF=5 A
=5 A, Tj=125 °C
I
F
IF=5 A, VR=40 V,
di/dt=100 A/µs
(see Figure 5)
=5 A, VR=40 V,
I
F
=125 °C, di/dt=100 A/µs
T
j
(see Figure 5)
2
-
1.6
22
-
14
1.3
35
-
40
2.2
V
V
ns
-
nC
A
ns
-
nC
A
Doc ID 11423 Rev 6 7/20
Page 8
Electrical characteristics STGx10NC60KD
2.1 Electrical characteristics (curves)
Figure 2. Output characteristics Figure 3. Transfer characteristics
Figure 4. Transconductance Figure 5. Collector-emitter on voltage vs
temperature
Figure 6. Gate charge vs gate-source voltage Figure 7. Capacitance variations
8/20 Doc ID 11423 Rev 6
Page 9
STGx10NC60KD Electrical characteristics
Figure 8. Normalized gate threshold voltage
vs temperature
Figure 10. Normalized breakdown voltage vs
temperature
Figure 9. Collector-emitter on voltage vs
collector current
Figure 11. Switching losses vs temperature
Figure 12. Switching losses vs gate resistance Figure 13. Switching losses vs collector
Doc ID 11423 Rev 6 9/20
current
Page 10
Electrical characteristics STGx10NC60KD
Figure 14. Thermal impedance for D²PAK,
DPAK and TO-220
Figure 16. Emitter-collector diode
) !
&-
characteristics
4 #
J
AXIMUMVALUES
M
4 #
J
TYPICALVALUES
6 6
&-
4 #
J
MAXIMUMVALUES
Figure 15. Turn-off SOA
Figure 17. Thermal impedance for TO-220FP
10/20 Doc ID 11423 Rev 6
Page 11
STGx10NC60KD Test circuits
3 Test circuits
Figure 18. Test circuit for inductive load
switching
Figure 19. Gate charge test circuit
Figure 20. Switching waveform Figure 21. Diode recovery time waveform
Doc ID 11423 Rev 6 11/20
Page 12
Package mechanical data STGx10NC60KD
4 Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
®
packages, depending on their level of environmental compliance. ECOPACK®
12/20 Doc ID 11423 Rev 6
Page 13
STGx10NC60KD Package mechanical data
Table 9. D
Dim.
A 4.40 4.60 0.173 0.181
A1 0.03 0.23 0.001 0.009
b 0.70 0.93 0.027 0.037
b2 1.14 1.70 0.045 0.067
c 0.45 0.60 0.017 0.024
c2 1.23 1.36 0.048 0.053
D 8.95 9.35 0.352 0.368
D1 7.50 0.295
E 10 10.40 0.394 0.409
E1 8.50 0.334
e 2.54 0.1
e1 4.88 5.28 0.192 0.208
H 15 15.85 0.590 0.624
J1 2.49 2.69 0.099 0.106
2
PAK package mechanical data
mm inch
Min. Typ. Max. Min. Typ. Max.
L 2.29 2.79 0.090 0.110
L1 1.27 1.40 0.05 0.055
L2 1.30 1.75 0.051 0.069
R 0.4 0.016
V2 0° 8° 0° 8°
Figure 22. D2PAK package drawing
0079457_M
Doc ID 11423 Rev 6 13/20
Page 14
Package mechanical data STGx10NC60KD
Table 10. DPAK package mechanical data
mm
Dim.
Min. Typ Max.
A 2.20 2.40
A1 0.90 1.10
A2 0.03 0.23
b 0.64 0.90
b4 5.20 5.40
c 0.45 0.60
c2 0.48 0.60
D 6.00 6.20
D1 5.10
E 6.40 6.60
E1 4.70
e2.28
e1 4.40 4.60
H 9.35 10.10
L1
L1 2.80
L2 0.80
L4 0.60 1
R0.20
V2 0
o
o
8
Figure 23. DPAK package drawing
14/20 Doc ID 11423 Rev 6
0068772_G
Page 15
STGx10NC60KD Package mechanical data
Table 11. TO-220FP package mechanical data
mm
Dim.
Min. Typ. Max.
A4.4 4.6
B2.5 2.7
D 2.5 2.75
E0.45 0.7
F0.75 1
F1 1.15 1.70
F2 1.15 1.70
G4.95 5.2
G1 2.4 2.7
H 10 10.4
L2 16
L3 28.6 30.6
L4 9.8 10.6
L5 2.9 3.6
L6 15.9 16.4
L7 9 9.3
Dia 3 3.2
Figure 24. TO-220FP package drawing
L7
A
B
Dia
L6
H
L2
D
L5
F2
F1
L4
E
F
G
G1
L3
7012510_Rev_K
Doc ID 11423 Rev 6 15/20
Page 16
Package mechanical data STGx10NC60KD
Table 12. TO-220 type A mechanical data
mm
Dim.
Min. Typ. Max.
A4.40 4.60
b0.61 0.88
b1 1.14 1.70
c0.48 0.70
D 15.25 15.75
D1 1.27
E 10 10.40
e2.40 2.70
e1 4.95 5.15
F1.23 1.32
H1 6.20 6.60
J1 2.40 2.72
L13 14
L1 3.50 3.93
L20 16.40
L30 28.90
∅P3.75 3.85
Q2.65 2.95
Figure 25. TO-220 type A package drawing
16/20 Doc ID 11423 Rev 6
0015988_S
Page 17
STGx10NC60KD Packaging mechanical data
5 Packaging mechanical data
D2PAK FOOTPRINT
TAPE AND REEL SHIPMENT
REEL MECHANICAL DATA
DIM.
A 330 12.992
B 1.5 0.059
C12.8 13.2 0.504 0.520
D 20.2 0795
G 24.4 26.4 0.960 1.039
N 100 3.937
T 30.4 1.197
mm inch
MIN. MAX. MIN. MAX.
TAPE MECHANICAL DATA
DIM.
A0 10.5 10.7 0.413 0.421
B0 15.7 15.9 0.618 0.626
D 1.5 1.6 0.059 0.063
D1 1.59 1.61 0.062 0.063
E1.651.85 0.065 0.073
F 11.4 11. 6 0.449 0.456
K0 4.8 5.0 0.189 0.197
P0 3.9 4.1 0.153 0.161
P1 11.9 12.1 0.468 0.476
P2 1.9 2.1 0.075 0.082
R 50 1.574
T0.250.35 0.0098 0.0137
W 23.7 24.3 0.933 0.956
mm inch
MIN. MAX. MIN. MAX.
BASE QTY BULK QTY
1000 1000
Doc ID 11423 Rev 6 17/20
Page 18
Packaging mechanical data STGx10NC60KD
DPAK FOOTPRINT
All dimensions are in millimeters
TAPE AND REEL SHIPMENT
REEL MECHANICAL DATA
DIM.
A 330 12.992
B 1.5 0.059
C 12.8 13.2 0.504 0.520
D 20.2 0.795
G 16.4 18.4 0.645 0.724
N 50 1.968
T 22.4 0.881
mm inch
MIN. MAX. MIN. MAX.
TAPE MECHANICAL DATA
DIM.
A0 6.8 7 0.267 0.275
B0 10.4 10.6 0.409 0.417
B1 12.1 0.476
D 1.5 1.6 0.059 0.063
D1 1.5 0.059
E 1.65 1.85 0.065 0.073
F 7.4 7.6 0.291 0.299
K0 2.55 2.75 0.100 0.108
P0 3.9 4.1 0.153 0.161
P1 7.9 8.1 0.311 0.319
P2 1.9 2.1 0.075 0.082
R 40 1.574
W 15.7 16.3 0.618 0.641
mm inch
MIN. MAX. MIN. MAX.
BASE QTY BULK QTY
2500 2500
18/20 Doc ID 11423 Rev 6
Page 19
STGx10NC60KD Revision history
6 Revision history
Table 13. Document revision history
Date Revision Changes
14-Jun-2005 1 New release.
19-Jul-2005 2 Complete version.
27-Jan-2006 3 Inserted ecopack indication.
01-Mar-2006 4 The document has been reformatted.
08-Feb-2007 5 Modified value on Table 6.: Switching on/off (inductive load).
24-Nov-2009 6 Inserted DPAK package option.
Doc ID 11423 Rev 6 19/20
Page 20
STGx10NC60KD
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
20/20 Doc ID 11423 Rev 6
Loading...