Dascom T2250 User Manual

User Guide IGP for Dot Matrix Printers

IGP for Dot Matrix Printers User Guide

Scope

This User Guide is to be considered as an enhancement to the standard documentation of your printer. Hence keep the printer’s standard documentation ready as your particular printer model is pictured in detail.

Table of Contents

Subject Listing

Table of Contents

SCOPE........................................................................................................................................................... 2

CHAPTER 1: CONTROL PANEL ............................................................................................................ 7

BASIC ELEMENTS ........................................................................................................................................ 7

MENU STRUCTURE...................................................................................................................................... 8

MENU PARAMETERS.................................................................................................................................... 9

MENU PRINTOUT EXAMPLE....................................................................................................................... 17

WEBPANEL ENHANCEMENTS .................................................................................................................... 19

ADVANCED MENU..................................................................................................................................... 20

PJL FUNCTIONS......................................................................................................................................... 21

CHAPTER 2: EMULATIONS.................................................................................................................. 23

MT660 EMULATION.................................................................................................................................. 23

Character Definition and Format ........................................................................................................ 23

Attributes, Print Position, and Type Styles....................................................................................... 23

Combining Attributes................................................................................................................... 24

Languages and Character Sets.......................................................................................................... 25

Primary and Secondary Fonts and Languages.............................................................................. 26

Selecting Primary and Secondary Sets......................................................................................... 27

Characters Per Inch .......................................................................................................................... 28

Character Height and CPI................................................................................................................. 29

Page Formatting................................................................................................................................... 30

Lines Per Inch................................................................................................................................... 30

Variable Line Spacing...................................................................................................................... 30

Horizontal Tabs................................................................................................................................ 31

Setting Tabs.................................................................................................................................. 31

Clearing Tabs ............................................................................................................................... 31

Setting Left and Right Margins........................................................................................................ 32

Setting Vertical Format........................................................................................................................ 33

Form Length Select .......................................................................................................................... 33

VFU Download Commands............................................................................................................. 34

VFU Load..................................................................................................................................... 34

VFU Load Errors................................................................................................................ .......... 34

VFU Data Format......................................................................................................................... 35

Paper and Print Position Movement.................................................................................................... 36

Reserved Control Codes................................................................................................................... 36

Horizontal Tab HT 09.............................................................................................................. 36

Form Feed FF 0C...................................................................................................................... 36

Vertical Tab VT 0B .................................................................................................................. 36

Carriage Return CR 0D ............................................................................................................ 36

Line Feed LF 0A...................................................................................................................... 37

Save Print Position ........................................................................................................................... 37

Restore Vertical Print Position......................................................................................................... 37

Relative Paper Motion...................................................................................................................... 38

Reverse Form Feed........................................................................................................................... 38

Forward Index .................................................................................................................................. 39

Reverse Index................................................................................................................................... 39

Partial Line Advance........................................................................................................................ 39

VFU Channel Commands................................................................................................................. 40

IGP for Dot Matrix Printers User Guide

Plot Mode............................................................................................................................................. 41

Plot Mode Commands...................................................................................................................... 41

Entering Plot Mode....................................................................................................................... 41

Exiting Plot Mode......................................................................................................................... 41

Align to Line Boundary................................................................................................................ 42

Plot Data........................................................................................................................................... 43

Plotting Dot Patterns......................................................................................................................... 45

Repeating a Pattern....................................................................................................................... 46

Stringing Commands Together..................................................................................................... 47

Plot Density...................................................................................................................................... 49

Paper Path Selection............................................................................................................................ 50

Select Tractor 1 ................................................................................................................................ 50

Select Tractor 2 ................................................................................................................................ 50

Select Tractor 3 ................................................................................................................................ 50

Select Single Sheet Feeder ............................................................................................................... 50

Select Auto Sheet Feeder Bin 1........................................................................................................ 50

Select Auto Sheet Feeder Bin 2........................................................................................................ 50

Postal Bar Code Printing..................................................................................................................... 51

POSTNET Bar Codes....................................................................................................................... 51

Four-State Bar Codes ....................................................................................................................... 52

PLANET Bar Codes......................................................................................................................... 52

Miscellaneous Functions...................................................................................................................... 53

Reset Printer to Powerup Settings.................................................................................................... 53

Alternate Escape Sequences............................................................................................................. 53

Emulation and Configuration Switching.......................................................................................... 53

Reserved Control Codes....................................................................................................................... 54

Escape Sequence Summary .................................................................................................................. 55

IBM PROPRINTER III XL EMULATION....................................................................................................... 57

Exceptions ............................................................................................................................................ 57

Enhancements....................................................................................................................................... 57

EPSON FX-1180 EMULATION.................................................................................................................... 58

Exceptions ............................................................................................................................................ 58

Enhancements....................................................................................................................................... 59

PRINTRONIX P6000 EMULATION ............................................................................................................... 60

HP 2564C EMULATION ............................................................................................................................. 61

Enhancements....................................................................................................................................... 63

GENICOM ANSI EMULATION .................................................................................................................... 64

Exceptions ............................................................................................................................................ 66

Enhancements....................................................................................................................................... 67

GRAPHICS LANGUAGE EMULATIONS......................................................................................................... 68

QMS Code V Emulation ....................................................................................................................... 68

Printronix Graphics Language Emulation........................................................................................... 71

Graphics Language Exceptions............................................................................................................ 74

CHAPTER 3: TRUETYPE FONTS......................................................................................................... 75

Maximum Character Size..................................................................................................................... 75

The PGL FONT Command................................................................................................................... 76

CHAPTER 4: MISCELLANEOUS.......................................................................................................... 77

Driver ................................................................................................................................................... 77

Cutting Device...................................................................................................................................... 77

Standard Documentation...................................................................................................................... 77

Table of Contents

Figure Listing

IGURE 1 - CONTROL PANEL ELEMENTS.......................................................................................................... 7

FIGURE 3 - CONTROL PANEL MENU STRUCTURE ............................................................................................. 8

FIGURE 4 - WEBPANEL ENHANCEMENTS....................................................................................................... 19

FIGURE 5 – CHARACTER DEFINITION AND FORMAT CODES........................................................................... 24

FIGURE 6 – LANGUAGE AND CHARACTER SET SELECTIONS .......................................................................... 25

FIGURE 7 – LANGUAGE AND FONT SELECTIONS ............................................................................................ 26

FIGURE 8 – CPI SELECTIONS ......................................................................................................................... 28

FIGURE 9 – CHARACTER HEIGHT MULTIPLIERS............................................................................................. 29

FIGURE 10 – LPI SELECTIONS ....................................................................................................................... 30

FIGURE 11 – SAMPLE VFU DOWNLOAD........................................................................................................ 35

FIGURE 12 – VFU CHANNEL VALUES ........................................................................................................... 40

FIGURE 13 – ALIGNMENT USING MODPLOT.................................................................................................. 42

FIGURE 14 – PLOT DATA FORMAT................................................................................................................. 43

FIGURE 15 – SAMPLE DOT PATTERN CODE ................................................................................................... 43

FIGURE 16 – SAMPLE BIT PATTERN............................................................................................................... 44

FIGURE 17 – DOT PATTERNS AND IDENTIFIERS ............................................................................................. 45

FIGURE 18 – REPETITION CONVERSION TABLE.............................................................................................. 46

FIGURE 19 – MT660 CONTROL CODES.......................................................................................................... 54

FIGURE 20 – MT660 ESCAPE SEQUENCE SUMMARY ..................................................................................... 56

FIGURE 21 – FX-1180 SUPPORTED CHARACTER SETS................................................................................... 58

IGP for Dot Matrix Printers User Guide

ACKNOWLEDGMENTS: “IBM" and “Proprinter” are trademarks of International Business Machines Corporation.

“Printronix” and “PGL” are trademarks of Printronix, Inc. “Epson” is a trademark of Seiko Epson Corp. “QMS” and “Code V” are trademarks of Konica Minolta-QMS Inc. “HP” is a trademark of Hewlett-Packard Company. “Genicom” is a trademark of Genicom L.L.C. “Acrobat

This printer makes use of the FreeType Engine software in accordance with the FreeType Project License, based in part on the Catharon Typography Project in accordance with the Catharon Open Source License.

Reader” is a trademark of Adobe Systems Incorporated.

Chapter 1: Control Panel

The panel consists of 2 Function Keys (Online sets the printer to online/offline mode, Setup enters setup mode) and 4 situation dependent soft keys (1, 2, 3, 4). The function of the soft keys is denoted by the display. For further explanations of the control panel functions, please refer to the User Guide of the printer.

On some printer models the menu may be locked. In order to enter the menu in this case, press the Menu key (1) for approximately 5 seconds.

Basic Elements

NOTE: For further informations on the control panel please refer to the printers

2 x 16 Digit

LCD

2 3 4

Online

Setup

Figure 1 - Control Panel Elements

Quick Start Guide or the User Guide on the Online CD-ROM.

1,2,3,4 “Soft Keys”

The function is denoted by the display

Online sets printer to online / offline Setup enters set-up mode

IGP for Dot Matrix Printers User Guide

Menu Structure

Back

PapOpt

Back

Print Menu

Reset Quietm.

Font CPI

LPI Skip

FFatTOF Compr 8

Graphic

Emulate

Back

Printer

dependent

Sl.Zero

Paper AutoTear

Printer

dependent

VFU

Printer

VTChan

dependent

Single Trac 1

dependent

VFUEnab

SkpWhn

Printer

VTChan

(future)

Printer

dependent

CVCC CV Lang

SFCC PG Lang

PY Then PN Then

Modplot Sz1 Font

Version Descend

Vscale Bar Res

Freefmt Auto PY

DarkBar Dot Pos

BlkMaxH BlkMaxH

ESC Alt ESC

MenLock Op Lang

Line Wr Wrap LF

Auto-CR Auto-LF

LtMarg RtMarg

Lang Charset

Code 7F Pr80-9F

Bidir I/O

Serial

Interf.

Baud Format

Protocol DTR

Formlen FormAdj

Lines Standard

Buffer ETH-INT

IPAddr

Gateway

Subnet

Next Back

OCTET 1 OCTET 2 OCTET3 OCTET 4

Figure 2 - Control Panel Menu Structure

Chapter 1: Control Panel

Menu Parameters

Factory settings are marked with *

Parameter group Parameter Description

Print (none) A list of the menus with the current setting is

printed.

Menu Load Menu = 1*

Load Menu = 2 Load Menu = 3 Load Menu = 4 Load Menu = 5

Reset

Quietm. Quietm. = On

Font Draft

CPI 5 CPI, 6 CPI,

LPI 1,5 LPI, 2 LPI, 3 LPI,

Skip Skip = 0.0 Inch*

FFatTOF Off

Compr 8 Off*

Reset Menu 1...5 No* Yes

Quietm. = Off*

Roman NLQ Roman LQ Sans Serif NLQ Sans Serif LQ Courier NLQ Courier LQ OCR-B NLQ OCR-B LQ OCR-A NLQ OCR-A LQ

6.67 CPI,

7.5 CPI, 8.6 CPI, 10 CPI*, 12 CPI,

13.3 CPI, 15 CPI,

17.1 CPI, 20 CPI

4 LPI, 5 LPI, 6 LPI*, 8 LPI, 9 LPI, 10 LPI, 12 LPI

Skip = 0.5 Inch Skip = 1.0 Inch Skip = 1.5 Inch Skip = 2.0 Inch Skip = 2.5 Inch Skip = 3.0 Inch Skip = 3.5 Inch

On*

A menu is loaded. Selection between five menus can be made.

The currently selected menu returns to the default values (factory settings).

Switches between normal and quiet mode printing. For all printing modes, the print-out is made with the bidirectional method in quiet mode printing. In the first step the first row of pins is activated, during the second step the second row is used.

Selects the character style and its quality. The abbreviation NLQ stands for Near Letter print quality, which means that the printer works faster but with a slightly lower resolution. LQ stands for Letter Quality, which means that the resolution is higher at the expense of a slightly slower speed.

Sets the characters per inch (character pitch).

Sets the lines per inch (line density).

Skips the perforation; 7 different values (in inches) can be defined.

Determines whether a Form Feed is invoked at Top Of Form. When set to Off, a host Form Feed command is ignored if the current position is at TOF.

Compressed 8 LPI. When set to On, all text printed at 8 LPI or greater is printed in the compressed font.

IGP for Dot Matrix Printers User Guide

Parameter group Parameter Description

Graphic CVCC

CV Lang

SFCC

PG Lang

PY Then

PN Then

1 : 94* : 255

US* UK Swe/Fin Nor/Dan Japan French Italian Spanish

1 : 126* : 255

ASCII* German Swedish Danish Norway Finnish English Dutch French Spanish Italian Turkish

None* All Term FreeFmt

Defines the decimal ASCII character code for the Code V Command Character

Defines the language substitution set for Code V block characters.

Defines the decimal ASCII character code between 1 and 255 for the PGL Command Character (called the Special Function Command Character by Printronix).

Defines the language substitution set for PGL block characters.

Defines how data on the same line as the Code V ^PY command is treated. The possible settings are:

None All data, plus the line terminator, are ignored. All All data is executed. Term All but the terminator is ignored. FreeFmt Characters on the ^PY line are ignored if the state of FreeFmt is On/Enabled in the Config Menu "Graphics" "FreeFmt".

Defines how data on the same line as the Code V ^PN command is treated. The possible settings are:

None All data, plus the line terminator, are ignored. All All data is executed. Term All but the terminator is ignored. FreeFmt Characters on the ^PN line are ignored if the state of FreeFmt is On/Enabled in the Config Menu "Graphics" "FreeFmt".

Parameter group Parameter Description

Graphic (continued) Modplot

Sz1Font

Version

Descend

Vscale

Bar Res

Freefmt

Auto PY

DarkBar

Dot Pos

On* Off

Roman HS Sana Serif HS Courier HS OCRA HS OCRB HS* Block

2* 1

Fixed* Auto

Off Style 1*

Low* High

On Off*

Off* On

On* Off*

Baseline* Top of Cell

Chapter 1: Control Panel

Determines whether text following graphics is re-aligned to the vertical spacing defined by the LPI setting, relative to Top of Form.

Selects the character style of the size 1 block character. This font style will be used only for horizontal size 1 block characters that are not reverse image, all other orientations and reverse image will use the block character font.

Note: In order to make size 1 block characters work within PGL reverse fields, the font chosen must be "Block".

Allows for the setting of Version 1 or Version 2 Code V (Default) compatibility.

Parameter controls the line spacing when descenders are present.

Parameter defines whether vertical block characters will be scaled to the same dimensions as horizontal block characters.

This control panel option applies only to Code V Extended Mode bar code commands. If you want the 300 DPI bar codes, but elect not to use the EXTENDED graphics commands, this menu option can be used. If High is selected you will get 300 DPI bar codes. If you select Low, you will get the standard 60 by 72 bar codes that appear on line printers. This switch only changes bar code dpi while in Code V (not PGL, etc.). This switch has no effect in the case where ^IPARAM,EXTENDED has been activated.

Option turns on free format in Code V graphics whenever a ^PY is encountered.

If Auto-PY is On, the printer is automatically in Code V graphics mode, and a ^PY command is not needed in the file being sent to the printer to begin Code V graphics.

Barcodes can be printed in two densities. "on" means 180 dpi Full Space. "off" means 180 dpi Half Space.

When set to "Baseline", the specified position is interpreted to be the baseline position of the character. Use this setting if you are upgrading from a line printer application. Use the “Top of Cell” setting if you are upgrading from a laser printer application.

IGP for Dot Matrix Printers User Guide

Parameter group Parameter Description

Graphic (continued) BlkMaxH

BlkMaxV

Emulate MT660*

ESC On*

Alt ESC On

Bidir Bidir = On*

I/O Serial Baud

Format

Protocol

0 to 136 Default: 40

0 to 136 Default : 40

P6000 EPSON FX IBM PROPRINTER HP2564C GENICOM

Off

Off*

Bidir = Off

Baud = 600 Baud = 1200 Baud = 2400 Baud = 4800 Baud = 9600* Baud = 19200

7 Bit No 2 Stop 7 Bit Even 1 Stop 7 Bit Odd 1 Stop 7 Bit Even 2 Stop 7 Bit Odd 2 Stop 7 Bit Mark 1 Stop 7 Bit Spc 1 Stop 7 Bit Mark 2 Stop 7 Bit Spc 2 Stop 8 Bit No 1 Stop* 8 Bit No 2 Stop 8 Bit Even 1 Stop 8 Bit Odd 1 Stop 8 Bit Mark 1 Stop 8 Bit Spc 1 Stop

XON/ XOFF* Robust XON/ XOFF ENQ/ STX ETX/ ACK ACK/NAK

Sets the maximum size black character (horizontally) that will be printed using the TrueType font. Characters above this maximum size will be printed using the previous vector style block characters.

Sets the maximum size black character (vertically) that will be printed using the TrueType font. Characters above this maximum size will be printed using the previous vector style block characters.

Selects the emulation.

Turns on or off the recognition of the ESC character

Turns on or off the recognition of the Alternate ESC character (^ in column 1)

On: Printer prints bi-directional. Off: Printer prints left to right.

Selects the baud rate. Printer and computer must have the same baud rate

Sets the number of data bits. The parity test for received data bytes can be selected. NO causes transmission in both directions without parity bit. If EVEN or ODD is selected, the bytes are checked if they have even or odd parity. The selection of MARK or SPACE causes a data byte transmission with parity bit, but without checking the received data. Transmission data with parity bit is always marked with 1 (MARK) or 0 (SPACE). Selects one or two stop bits per data byte.

Selects the protocol for data transmission

Parameter group Parameter Description

I/O (continued) DTR

Interf. Interf. = Share*

Buffer Buffer = 0 KB

ETH-INT

IP Addr

Gateway

Subnet

Code 7F Fill*

Pr80-9F Off

Lang US*

DTR = DTR* DTR = READY

Interf. = Parallel Interf. = Serial

… Buffer = 128 KB*

IP Addr = OCTET1 … IP Addr = OCTET4

Gateway = OCTET1 … Gateway = OCTET4

Subnet = 0 … Subnet = 255

Ignore Del Chr Del Buf Space

On*

UK French German Italian Swe/Fin Nor/Dan Spanish Japanese Portuguese Fren Eps UK Eps Nor/Dan Eps Ital Eps Span Eps Nor Eps Dan II Eps Span II Eps Lat Amer Eps

Chapter 1: Control Panel

DTR signal is assigned to DTR line READY signal is assigned to DTR line DTR = Pin 20 (25- pin female connector) DTR = Pin 4 ( 9- pin female connector)

Selects the interface. Printer is configured either for parallel or serial connection or in automatic change for both. Note: Serial is optional.

Selects the size of the interface buffer

In this parameter group you can choose settings for the internal Ethernet interface.

This menu level offers the possibility to set the IP address, which is divided into four digit groups (octet 1 to 4). Possible settings: 0 to 255

This menu level offers the possibility to set the Gateway address, which is divided into four digit groups (octet 1 to 4). Possible settings: 0 to 255

This menu level offers the possibility to set the Subnet mask address , which is divided into four digit groups (octet 1 to 4). Possible settings: 0 to 255

Determines what to do when a 7F character is parsed in the data stream.

Selects whether or not to print characters for codes 80-9F

Selects the language set defined by character substitution within the ASCII character set in locations 20 Hex to 7F Hex.

IGP for Dot Matrix Printers User Guide

Parameter group Parameter Description

Charset CP437

CP850 CP852 CP857 CP860 CP861 CP863 CP865 CP866 CP1250 CP1251 CP1252 CP1254 Italic Latin1* Latin2 Latin9 Cyrillic Turkish SAP8859-1 HP Roman8

LtMarg 1 to CPI X 13.6 Sets the left margin column. The maximum

RtMarg 1 to CPI X 13.6 Sets the right margin column. The maximum

Auto-CR Auto-CR = On

Auto-CR = Off*

Auto-LF Auto-LF = On

Auto-LF = Off*

Line-Wr Line-Wr = Off*

Line-Wr = On

Wrap-LF Wrap-LF=Off*

Wrap-LF=On

MenLock MenLock = Off

MenLock = Menu* MenLock = All

Op Lang English*

German French Italian Spanish

Selects the character set that defined the characters in location 80 Hex to FF Hex. Locations 20 Hex to 7F Hex will be the standard ASCII characters.

value is a function of the CPI times the printable area (13.6 inches)

Switches the automatic carriage return on or off after receiving the signal CR

Switches the automatic line feed (LF) on or off after receiving the signal CR

Parameter will cause an automatic Carriage Return when attempting to print data past the right margin

When this parameter and the Line Wrap parameter are both set to ON, an automatic Carriage Return and Line Feed will occur when attempting to print data past the right margin

MenLock = Menu : Menu-key is locked MenLock = All: Setup-, Paper-, Font, CPI locked. Printer power has to be toggled to activate locking The locked keys can only be re-activated by holding the Setup-key while switching the printer on.

The menu will be shown on the LC display in the selected language.

Parameter group Parameter Description

Paper Single Formlen Lines

Standard

FormAdj

Trac1 Formlen FormAdj

AutoTear View/Tear = Off*

6 : 72* : 132

No format DIN A3 DIN A4 DIN A5 DIN B5 DIN B6 DIN C6 Executive Letter Legal

FormAdj = 0/ 72" : FormAdj = 12/ 72"* : FormAdj = 220/ 72"

(same as above) (same as above)

View = 1s View = 3s View = 6s

Tear = 1s Tear = 3s Tear = 6s

Tear at TOF

Chapter 1: Control Panel

Selects the paper parameters for Formlen , FormAdj and Head, for the Single feed and Tractor feed forms.

Sets the form length by No of lines of the actual LPI setting. (E.g. 72 lines at 6 LPI will result in 12 ins form length). Form length may be selected in the range of 3 ins to 21 ins. Form length selected will not be affected by changing LPI later on.

Selects the form length by standard formats. The LC display will indicate "No format" if a Form length is selected by the Line function or ESC sequence, which does not correspond to a standard format

Sets the first print position of a form in n/72 inch, separately adjustable for each paper path.

NOTE: "Single" does not apply to some printer models.

Selects the Auto View / Auto Tear function. If Auto View is selected, paper will be moved to make the last printed line visible (Auto View position). When data is received paper will move to last print position and printing continues. If no data is received for the selected interval paper will be moved to Auto View position

If Auto Tear is selected, the perforation of the paper will be moved to the Tear-off position As soon as data is received the paper will move to the last print position and printing will continue. If no data is to be printed for the selected interval, paper will be moved to Tear-off position

If the parameter Tear at TOF is set, the paper perforation is automatically positioned at the tear off edge as long as the current print position is TOF. Feeding takes place after approx. 1.5 sec (hold time). If any data is received during this period of time printing will continue and the paper will not be fed to the tear-off position. It must be noted that the printer may only be switched off when the print position is at TOF.

IGP for Dot Matrix Printers User Guide

Parameter group Parameter Description

Sl.Zero Off*

VFU VFUEnab

VTChan

SkpWhn

PapOpt ASF-R

Off* On

1 : 12 Unused

Before* After

ASF-F Trac2 Trac3

AutoTRA AutoASF

Selects if normal zero (0) or the slashed zero (Ø) is printed.

Selects whether VFU is active for use with Vertical Format Units

Selects the Vertical tab channel

Sets up when paper movement happens on hitting bottom of form using VFUs

T2150/T2250

Activation of optional Tractors and SheetFeeders: installed or not installed.

T2265+…T2380

These Parameters only appear if at least one optional Tractor (TRA) or Sheet Feeder (ASF) is installed. It regulates the activation of optional paper ways when there is no more paper left in one of them: T1=T2=T3 and/or: ASF1=ASF2 or: Off

Menu Printout Example

NOTE: The actual print out of your printer may differ from this example.

Chapter 1: Control Panel

IGP for Dot Matrix Printers User Guide

Chapter 1: Control Panel

WebPanel Enhancements

Enhancements have been made to the WebPanel embedded web server pages to provide management of the features provided by the printer.

The Graphics page, which is special to the IGP printer, is shown below.

NOTE: Dependent on the printer model and the used Ethernet interface the menus

may slightly differ from the images shown below.

Figure 3 - WebPanel Enhancements

IGP for Dot Matrix Printers User Guide

Advanced Menu

In order to enter the Advanced Menu you need to keep the key "Online" pressed while switching on the printer. Once "Testmode" is displayed the Advanced Menu mode is activated.

Parameter group Parameter Description

ASCII80 ASCIIa136

H-Dump on

Formlen 11"

AGA always*

Paphand Headup

Cx-Bid on*

Wrap on*

Sound on*

Single on

Pap.back normal*

HvyForm on

Sleepmod on*

Serial N Asset N

GrSpeed triple*

GrFreq normal

Jobcntl off*

on off*

off*

12"

off once

on* off

Pagewid Leftzone Rightzone Physlm

off

dark

off*

off Variable Settings for the serial and the asset no. of the

normal double

high*

Prints self test 80 or 136 columns. Can be halted by pressing the Online key. Can only be exited by powering the printer off.

This test enables analyzing interface data sent from host to printer.

Defines default form length.

T2150/T2250

Determines how often the AGA (automatic gap adjustment = head to platen distance) is carried out.

T2265+ … T2380

Decides whether the AGA is on or the head gap needs to be set manually.

Settings to improve handling of critical paper.

Sets Parallel Interface to IEEE1284 on or off.

Enables/disables line wrap.

Enable/disables sound.

Default setting depends on printer model. Enables/disables the manual single sheet mode.

Suitable to improve paper handling with gray or colored rear side.

Improves quality of carbon copies.

Enables/disables Sleep mode.

printer. normal = 180 dpi graphic full space.

double = 180 dpi graphic half space. triple = 180 dpi graphic triple space. Choose triple for highest print speed.

T2150/T2250/T2265+/T2365 only. Improves graphic performance.

Job control disables/enables PJL commands.

Chapter 1: Control Panel

PJL Functions

The following PJL commands are implemented:

Command Short description T2x80(+)

T2x65(+)

T2x50

"ESC"%-12345X@PJL Universal Exit Language (UEL)

Commands @PJL ECHO ECHO Command X X @PJL EOJ @PJL EOJ NAME= @PJL INFO STATUS INFO (Information Request)

@PJL INFO CONFIG INFO of the printer configuration X @PJL INFO VARIABLES INFO of varibles which can be set

@PJL INFO MEMORY INFO about the Memory of the @PJL RDYMSG DISPLAY = RDYMSG (Ready Message) @PJL USTATUS DEVICE = ON

@PJL USTATUS DEVICE = OFF @PJL USTATUS DEVICE = VERBOSE @PJL USTATUS JOB = ON @PJL USTATUS JOB = OFF @PJL USTATUS PAGE = ON @PJL USTATUS PAGE = OFF @PJL USTATUSOFF @PJL JOB NAME = @PJL JOB FILE = @PJL JOB START = @PJL JOB END = @PJL JOB COPY = @PJL ENTER LANGUAGE Exit PJL and start normal parser X @PJL INFO USTATUS X X @PJL USTATUS TIMED X X

The PJL functionality works with the internal and external (TallyCom III) ethernet interface and can be switched on/off via the new setting JobCntrl (in the online menu). Default is “off”.

EOJ (End of Job) Commands: X

Command

by SET

printer

Command

USTATUS (Unsolicited Status)

Commands

JOB (Start of Job) Commands X

X X

X X X

X X -

- X

X X X X X X X X

X X X

Line

printer

X X

X X X X X X X X

X X X X X

IGP for Dot Matrix Printers User Guide

Chapter 2: Emulations

MT660 Emulation

This language is an emulation of the MT660 native language, which was based on the ANSI 3.64 standard. This language has been enhanced as needed throughout the development of the MT661 Series and T6000 Series printers. It is identified as the MT660 emulation on the control panel and in printer reports.

Character Definition and Format

This section presents and explains the Reserved Control Codes and Escape Sequences that control how printed output will look, where it will print, characters that are available, etc.

Attributes, Print Position, and Type Styles

This escape sequence is used for setting up fonts by allowing you to control the print attributes (boldface, underline, overline, etc.), print position (superscript and subscript), and type style selection. The basic sequence is:

ESC [ n1 ; n2 ; nx m ASCII Command

1B 5B 3B 3B 6D Hex Equivalent

This sequence changes both the primary and secondary fonts, but does not change the character set selected except when changing into or out of the OCR sets. In this command you may combine codes for attributes, print positions, and type styles. You may send all of the attributes available and the printer will act on all of them. However, when you send type style codes and super- and subscript codes, the printer will act only on the last type style code and whichever of the super- and subscript commands appears last.

The codes in the following lists may be listed in any order in the command. Each code must be separated from the following code by a semicolon.

Using this escape sequence, you can select such things as Italicized Courier font by sending a code to select the Courier type style along with a code to select italic printing (see the next section for an explanation of combining character definition and format codes).

IGP for Dot Matrix Printers User Guide

Parameter Code Parameter

ASCII HEX Description

Attribute Selections

4 34 Underline 3 33 Italic

1 31 Boldface 60 3630 Overline 61 3631 Strikethrough

0 30 End Attribute

Print Position

62 3632 Superscript printing 63 3633 Subscript printing

0 30 End Super-/subscript

Type Styles

10 3130 Data Processing 11 3131 Gothic 12 3132 OCR-A 13 3133 OCR-B 14 3134 Draft 15 3135 Courier

100 313030 Roman 101 313031 San-Serif 102 313032 Prestige

Figure 4 – Character Definition and Format Codes

Combining Attributes

As we mentioned, any of the attributes discussed in the ESC [nm sequence may be included in a single escape sequence. The escape sequence begins the same as one requesting a single code but changes after the first attribute byte. A semicolon (;) must be inserted between each code listed in the sequence. For example, to print a single word in a sentence with the boldface and underline attributes, send the escape sequence

ESC [ 1 ; 4 m

1B 5B 31 3B 34 6D

immediately before the word in the data stream and follow the word with the escape sequence:

ESC [ 0 m

1B 5B 30 6D

Example: To boldface and italicize the word "only" in the sentence:

Enter: Boldface and italicize the word ESC[1;3monlyESC[0m in this sentence. Printer Output: Boldface and italicize the word only in this sentence.

Chapter 2: Emulations

Languages and Character Sets

The numerous language and character set selections are defined in the Character Sets section of this manual. The following commands can be used:

Language Panel Display MT660 G0 MT660 G1

ISO 4 – UK ISO 6 – US ISO 11 – Swedish/Finnish ISO 14 – Japanese ISO 15 – Italian ISO 16 – Portuguese ISO 17 – Spanish ISO 21 – German ISO 60 – Nor/Danish ISO 69 – French

Character Set Panel Display MT660 G0 MT660 G1

Code Page 437 – IBM Proprinter Code Page 850 – Latin 1

Code Page 852 – Latin 2 Code Page 857 – Turkish Code Page 860 – Portuguese Code Page 861 – Icelandic Code Page 863 – French Canadian Code Page 865 – Nordic Code Page 866 – Cyrillic Code Page 1250 – Win 98 Latin 2 Code Page 1251 – Win 98 Cyrillic Code Page 1252 – Win 98 Latin 1 Code Page 1254 – Win 98 Turkish ISO 8859-1 – Latin 1

ISO 8859-2 – Latin 2 ISO 8859-15 – Latin 9

ISO 8859-5 – Cyrillic ISO 8859-9 – Turkish

HP Roman-8 SAP 8859-1 Italic

UK ESC(A ESC)A US ESC(B ESC)B Swe/Fin ESC(H ESC)H Japanese ESC(J ESC)J Italian ESC(Y ESC)Y Portuguese ESC(L ESC)L Spanish ESC(Z ESC)Z German ESC(K ESC)K Nor/Dan ESC(’ ESC)’ French ESC(f ESC)f

CP437 ESC(0x80 ESC)6 or

ESC)0x80 CP850 ESC(0x82 ESC)0x82 CP852 ESC(0x87 ESC)0x87 CP857 ESC(0x8D ESC)0x8D CP860 ESC(0x84 ESC)0x84 CP861 ESC(0x94 ESC)0x94 CP863 ESC(0x85 ESC)0x85 CP865 ESC(0x86 ESC)0x86 CP866 ESC(0x8E ESC)0x8E CP1250 ESC(p ESC)p CP1251 ESC(q ESC)q CP1252 ESC(r ESC)r CP1254 ESC(. ESC). Latin1 ESC,A or

ESC(%

Latin2 ESC(& or

ESC,B Latin9 ESC(/ ESC)/ Cyrillic ESC(* ESC)* or

Turkish ESC(. ESC). HP Roman8 ESC(0x83 ESC)0x83 SAP8859-1 ESC(+ ESC)+ Italic ESC(Y or

ESC (4

ESC-A or ESC)% ESC)& or ESC-B

ESC-L

ESC)Y or ESC)4

Figure 5 – Language and Character Set Selections

IGP for Dot Matrix Printers User Guide

Primary and Secondary Fonts and Languages

This escape sequence allows a font style and some language substitutions to be loaded into the primary (G0) and secondary (G1) areas. To load your primary and alternate character sets, use the sequence:

ESC [ n1 ; n2 ! s

1B 5B 3B 21 73

Where:

= the value field for the primary (G0) character set.

= the value field for the alternate (G1) character set.

There are six groupings of Character Sets to select from on your printer.

ASCII Values

Language Gothic Courier Draft DP

(user default) 10 40 100 or 700 0

US 11 41 101 or 701 1

German 12 42 102 or 702 2

Norwegian/Danish–T6 13 43 103 or 703 3

French–T6 14 44 104 or 704 4

UK 15 45 105 or 705 5

Spanish 16 46 106 or 706 6

Swedish/Finnish–T6 17 47 107 or 707 7

Italian–T6 18 48 108 or 708 8

Special Characters 19 49 109 or 709 9

Character Set ASCII

OCR-A 600 OCR-B 610

Figure 6 – Language and Font Selections

In the examples that follow, we show you how to use this escape sequence in a variety of ways.

Example 1:

To select US Data Processing as the primary set (n alternate set (n

= 8) use the escape sequence:

= 1) and Italian Data Processing as the

ESC [ 1 ; 8 ! s

1B 5B 31 3B 38 21 73

Example 2:

You may change to another primary set without changing the alternate set by omitting n

in the

sequence. For example, the original escape sequence shown above can be modified to:

ESC [ 1 2 ! s

1B 5B 31 32 21 73

This escape sequence would change the primary character set to German Gothic

= 12). The alternate character set remains unchanged.

Example 3:

Chapter 2: Emulations

To change the alternate character set to the Spanish Courier (n

= 46) without changing the

primary set, modify the escape sequence to:

ESC [ ; 4 6 ! s

1B 5B 3B 34 36 21 73

Selecting Primary and Secondary Sets

There are two ways to access the primary and alternate character sets. Once the primary and alternate character sets are loaded, they can be accessed using the Shift In (SI, HEX 0F) and Shift Out (SO, HEX 0E) codes to select the sets for actual printing; SI selects the primary set, and SO selects the alternate set.

The second way to access the primary and alternate character sets uses the 8th bit to select either primary or alternate set. To use this method, set the 8th Bit Parameter to Data in the Configuration Menu. With 8th Bit set to Data, when the 8th bit is high, it performs the same function as the SO Command; it selects the Alternate Character Set. When the 8th bit is low, it performs the same function as the SI Command; it selects the Primary Character Set.

IGP for Dot Matrix Printers User Guide

Characters Per Inch

The following escape sequence selects the characters per inch (CPI):

ESC [ n w

1B 5B 77

Where:

n = A value from the table below.

CPI ASCII HEX

5 CPI 9 39 6 CPI 10 3130

6.5 CPI 14 3134

6.67 CPI 11 3131

7.5 CPI 12 3132

8.33 CPI 13 3133

8.57 CPI 15 3135 9 CPI 19 3139

10 CPI 4 34 12 CPI 5 35

12.5 CPI 16 3136

13.33 CPI 8 38 15 CPI 1 31

16.67 CPI 6 36

17.14 CPI 17 3137 18 CPI 18 3138 20 CPI 7 37

Figure 7 – CPI Selections

The CPI value may be changed at any time. However, selecting a new CPI value cancels a previous horizontal size selection (see the next escape sequence), and selecting a new horizontal size cancels the previous CPI value.

Chapter 2: Emulations

Character Height and CPI

This sequence allows you more control over how characters will look when they are printed out on the printer. With this command you can change both the character height and the character width. This allows you to print in wide characters for increased readability. To change character size, use the following escape sequence:

ESC [ n1 ; n2 Sp B

1B 5B 3B 20 42

Where:

= one of the values from the following table.

n1 values Char Height

ASCII HEX amount of increase

100 313030 = normal height 200 323030 = twice normal height

Figure 8 – Character Height Multipliers

Note: Changing the height of a character set will change the distance the paper moves in response to a Line Feed Command.

= a width multiplier in the range of 1 (.01x) to 1000 (10x). For example, a

value of 50 would be .50 X 10 CPI = 5 CPI, and a value of 200 would be 2.00 X 10 CPI = 20 CPI. The result is variable to within a decipoint, so that a value of 128 would be 1.28 X 10 CPI = 12.8 CPI.

The table above lists all of the available CPIs on this emulation and the values used to select them. This command will work with any alphanumeric font.

A new CPI selection will cancel the horizontal size selected with this command, and selecting a new horizontal size cancels the previous CPI selection.

IGP for Dot Matrix Printers User Guide

Page Formatting

Many of the parameters for formatting the print and page characteristics (such as LPI, Horizontal Tabs, etc.) can be set from your host computer using escape sequences. This section discusses and explains the Escape Sequences and Reserved Control Codes used for page formatting.

Lines Per Inch

The following escape sequence selects lines per inch (LPI):

ESC [ n z

1B 5B 7A

Where:

n = one of the values from the table below.

LPI n Value

Selection ASCII HEX

1.5 LPI 7 37 2 LPI 8 38 3 LPI 9 39 4 LPI 10 3130 5 LPI 11 3131

6 LPI* 3 33

7 LPI 12 3132 8 LPI 4 34 9 LPI 13 3133

10 LPI 6 36 11 LPI 14 3134 12 LPI 15 3135 15 LPI 16 3136

*Default LPI value

Figure 9 – LPI Selections

The LPI may be changed anywhere on a form. The current LPI setting is used to compute the physical form length when loading a VFU or selecting a form length. Changing the LPI does not change the physical form length, bottom-of-form skip, vertical tab stops, or VFU channel positions. However, it does change the size of the units by which they are set and reported. For example, an 11 inch form at 6 LPI has 66 lines, but the same form length has 88 lines at 8 LPI.

Variable Line Spacing

You may set up these emulations to use variable line spacing in increments of n/720". To set up variable line spacing, use the sequence:

ESC [ < n Sp h space required before h

1B 5B 3C 20 68

Where:

n = Desired line spacing in increments of n/720".

Chapter 2: Emulations

Horizontal Tabs

The MT660 sets default tabs at every eighth column. The following commands allow the user to manipulate Horizontal Tabs according to job requirements.

Setting Tabs

To set up to 16 horizontal tabs, use the sequence:

ESC [ n1 ; n2 ; n3 ; ...n16 u

1B 5B 3B 3B 3B 75

Where n specified).

Example:

To set horizontal tabs at columns 15, 30, and 45, use the sequence:

ESC [ 15 ; 30 ; 45 u

1B 5B 3135 3B 3330 3B 3435 75

Current Position

Horizontal tabs may also be set at the current position while sending a line of print data. To set a horizontal tab at the current position, use the sequence:

ESC H

1B 48

Clearing Tabs

To clear tab stops at specific columns, use the sequence:

ESC [ n1 ; n2 ; n3 ; ...n16 q

1B 5B 3B 3B 3B 71

= The column numbers assigned as tab stop locations (up to 16 may be

1–n16

Where n

Clearing All Horizontal Tabs

To clear all horizontal tabs (including the default tab settings), use the sequence:

ESC [ 3 g

1B 5B 33 67

Clearing Current Horizontal Tab

To clear a horizontal tab at the current position, use the sequence:

ESC [ 0 g

1B 5B 30 67

= Previously selected tab stops that will be removed.

1–n16

IGP for Dot Matrix Printers User Guide

Setting Left and Right Margins

This escape sequence allows the user to set the left and right margins from the host. However, instead of using column numbers, which change when the CPI setting is changed, this command sets absolute margins in increments of 1/120 of an inch that do not change location when the CPI selection is changed.

The basic margin setting sequence is:

ESC [ LM ; RM " s

1B 5B 3B 22 73

Each margin setting is calculated from the first dot position on the page. For example, if you want the left margin set 1 inch from the first dot position and the right margin set at 8 inches from the first dot position, multiply 120 x the desired inch setting and enter that amount in the proper location in the escape sequence.

To finish this example, you would finally enter margin values of 120/120 and 960/120, which would give you the escape sequence:

ESC [ 120 ; 960 " s

1B 5B 313230 3B 393630 22 73

Chapter 2: Emulations

Setting Vertical Format

The top of the first line of print on a page is called the top-of-form (TOF) position. Vertical position is measured from this point. The form length is the distance from one TOF to the next. The bottom-of-form (BOF) skip is the distance between the last line of print on the page and the next TOF. Once the TOF and form length have been set, the paper will automatically advance to the next TOF whenever the print position advances into the BOF skip area. Vertical formatting includes the following settings:

Physical length of the total form. Position of the first printed line on a form (TOF). Position of bottom-of-form and/or bottom-of-form skip. Position of any other vertical stops on a form.

There are three ways to set vertical format. One way involves using the menus on the printer to set the desired parameter values through the control panel. The other ways involve sending escape sequences or control codes from the host computer.

Form Length Select

In the IEEE 1284 interface the form length can be selected through the control panel or by sending the Form Length Select (FLS) escape sequence from the host. The basic FLS escape sequence is:

ESC [ n t

1B 5B 74

Where: n = Form Length

If n = : 0, form length is 11 inches. 1, form length is 12 inches. 2–255, form length is equal to the value of n (in lines). The FLS Command resets the current paper position as the TOF. Make sure the

paper is aligned at the desired top-of-form before sending the FLS Command. To calculate form length, multiply the form length in inches by the lines per inch.

For instance, a 15.5" form printed at 6 LPI has a form length of 93 lines:

15.5" Form Length x 6 LPI = 93 (Total lines on form) To set the form length for a 15.5" form, send the sequence:

ESC [ 93 t

1B 5B 3933 74

Even though the form length can be set in number of lines, the printer divides the Form Length in lines by the LPI setting and stores the form length in inches, not number of lines. Subsequent changes in LPI will not change the physical form length.

IGP for Dot Matrix Printers User Guide

VFU Download Commands

VFU download commands are used with the IEEE 1284 and serial interfaces only. The VFU Load not only sets values for the form length and bottom-of-form skip (see also, Skp Whn in

Chapter 2), but also sets up vertical tabs on the page that are used by VFU Channel Commands. Load the printer VFU memory from your computer and then use VFU Channel Commands to move the paper to specific locations. Your printer uses electronic memory for its VFU, allowing the page format to be defined by commands from your computer up to a maximum storage of 255 lines.

Form lengths and vertical tab positions stored in the VFU memory are based on the Lines Per Inch (LPI) setting in effect at the time the VFU is loaded. Settings are not affected by changes in LPI or by entering Plot Mode.

VFU Load

To load the VFU, two escape sequences are needed, one to begin and one to end the load. The VFU Load Command resets the current paper position as the top-of-form. Make sure the

paper is aligned at the desired top-of-form before sending the VFU Load Command. To begin a VFU download, use the sequence:

ESC [ < 1 h

1B 5B 3C 31 68

To end a VFU download, use the sequence:

ESC [ < 1 l l = lower-case L

1B 5B 3C 31 6C

After the Begin-load escape sequence, all data, except ASCII control codes, is treated as VFU formatting information and is placed in VFU memory. All ASCII control codes and Escape sequences are ignored except the End-load sequence.

VFU Load Errors

All data must be in the proper VFU Load format. If an error occurs during the load or a load overruns memory length, the load is canceled and any remaining VFU data is printed. Canceled loads default to the current form length setting (as set from the control panel or with the FLS Escape Sequence).

To use the Vertical Format Units you download you must send a Vertical Channel Command, discussed below.

Chapter 2: Emulations

VFU Data Format

The VFU Data Format includes two bytes of data for each line of the form, starting with line 1. The two bytes of data indicate channel number(s). Traditionally, Channel 1 is reserved for TopOf-Form (TOF) and Channel 12 is reserved for Bottom-Of-Form (BOF). The Vertical Tab (VT) Control Code moves the paper forward to the next marked tab position on Channel 2. The format for the byte pair is:

Bit: 7 6 5 4 3 2 1 0

Value: x 1 C6 C5 C4 C3 C2 C1 Byte 1

x 1 C12 C11 C10 C9 C8 C7 Byte 2

Where:

Bit 7 (x) = Not used. Bit 6 = Always 1. Bits 0–5 = VFU channels (C1–C12 = channels 1–12).

1 = channel present 0 = no channel

The byte-pairs for a sample load are shown below. The form length used for this example is 16 lines long; therefore, 16 byte-pairs are needed.

Byte Line Binary HEX Channel or Byte Line Binary HEX Channel or

# # Value Value Function # # Value Value Function

1 1 x1000001 41 1 17 9 x1000000 40 2 x1000000 40 18 x1000000 40 3 2 x1000000 40 19 10 x1000000 40 4 x1000000 40 20 x1000000 40 5 3 x1000000 40 21 11 x1100100 64 6 and 3 6 x1000000 40 22 x1000000 40 7 4 x1000000 40 23 12 x1000000 40 8 x1000000 40 24 x1000000 40

9 5 x1000000 40 25 13 x1000000 40 10 x1000000 40 26 x1000000 40 11 6 x1000000 40 27 14 x1000000 40 12 x1000000 40 28 x1000000 40 13 7 x1000010 42 2 29 15 x1000000 40 14 x1000000 40 30 x1100000 60 12 15 8 x1000000 40 31 16 x1001000 48 4 16 x1000000 40 32 x1000010 42 8

ESC[<1h

Start Code

ESC[<1l

Stop Code

Figure 10 – Sample VFU Download

IGP for Dot Matrix Printers User Guide

Paper and Print Position Movement

There are varieties of commands and escape sequences used to select paper and print movement functions. In this section, we present both the reserved commands and escape sequences.

When entering or exiting the Character or Plot modes, any data in the print buffer is printed. In Character Mode, the print position moves to the left margin of the current line, or to the current dot row in Plot Mode. If no paper motion command is issued, printing continues at the current print position. The following commands affect print position by moving the paper vertically or print position horizontally or both.

Reserved Control Codes

Horizontal Tab HT 09

This control code moves the print position to the next horizontal tab stop on a line. For multiple tabs, string multiple HT Control Codes together. The printer ignores HT Control Codes if horizontal tabs are not set or if the command is placed in a line beyond the available tabs.

By default, the printer sets a tab stop every 8 columns. These default tab stops can be altered or cleared using the Horizontal Tab Escape Sequence, listed earlier in this chapter.

In the MT660 Emulation, horizontal tab stops change physical location with a change of the left margin or CPI. For example, if a stop is set at column 16, it will always be 15 columns from the left margin, but the physical distance will change for all CPIs.

Form Feed FF 0C The FF Control Code advances the paper to the first print position of the next form.

Vertical Tab VT 0B

When the VFU is enabled, the VT Control Code is used to advance the paper to the next VT Channel location whether the printer is in Character Mode or Plot Mode.

The VT Channel is selected through the printer control panel. If the VFU is not enabled, a VT Command causes a single line feed. If POPC is enabled, the preceding buffer contents are printed before the VT Command is performed.

Carriage Return CR 0D

The Carriage Return (CR) Control Code moves the print position back to the left margin. In Automatic Line Feed Mode (Auto LF), when the printer encounters a CR Command, any

printable data previously received is printed and the current print position (cursor) moves to the first column of the next line.

Chapter 2: Emulations

Line Feed LF 0A

The Line Feed (LF) Control Code advances the paper one line in Character Mode or one dot-row in Plot Mode.

If the Auto Carriage Return Parameter is set to ON, the printer also moves the print position to the left margin when it receives a Line Feed Command.

If Print on Paper Command (POPC) is enabled, any character data previously received is printed before the move.

Character Mode

When a LF Command is issued in Character Mode, the actual distance the paper moves in response to a single LF Command depends on the LPI or the Variable Line Spacing setting.

Plot Mode

When a LF Command is issued in Plot Mode, the actual distance the paper moves depends on the plot density setting for vertical DPI. For example, with a density of 100 dots per inch the paper would advance 1/100", and with a density of 50 dots per inch the paper would advance 1/50”.

Save Print Position

The Save Print Position (SPP) Command saves the current print position into the printer’s memory. The SPP escape sequence is:

ESC P B

1B 50 42

Restore Vertical Print Position

The Restore Vertical Print Position Command moves the paper to the last saved vertical cursor position. If no vertical cursor position has been saved on the current form, the paper moves to the current top-of-form. In either case, the active print position is moved to the left margin. The escape sequence is:

ESC P A

1B 50 41

IGP for Dot Matrix Printers User Guide

Relative Paper Motion

The Relative Paper Motion (RPM) Command moves the paper forward or backward a requested number of increments from its current print position. Movement distance is dictated by the print mode (Character or Plot).

Exceptions:

Reverse paper motion stops at the Top-Of-Form (TOF) location on the current form.

Forward motion into a Bottom-Of-Form (BOF) skip area advances the paper to the next TOF, then forward motion continues the remaining number of increments.

The relative paper motion escape sequence is:

ESC [ c n n ! v

1B 5B 63 21 76

Where:

c = Paper movement direction. 0 = forward paper motion 9 = reverse paper motion

nn = Number of increments the paper moves.

Range = 1 to 99 ASCII or 31 to 3939 HEX.

Example 1:

Moving the paper forward 5 lines.

ESC [ 0 0 5 ! v

1B 5B 30 30 35 21 76

Example 2:

Moving the paper backward 13 lines.

ESC [ 9 1 3 ! v

1B 5B 39 31 33 21 76

Reverse Form Feed

The Reverse Form Feed Command moves the paper backward to the top-of-form (TOF) position of the current form. If the paper is already positioned at the TOF when this command is received, no movement will occur. The Reverse Form Feed escape sequence is:

ESC [ f

1B 5B 66

Chapter 2: Emulations

Forward Index

The Forward Index Command moves the paper forward one line with no change in horizontal position. This command is valid only in Character Mode; it is not allowed in Plot Mode. The Forward Index escape sequence is:

ESC D

1B 44

Example:

Input: A Output: A

B C D

After the CRLF, the print position would be on this line at the left margin.

ESCDBESCDCESCDDCRLF

Reverse Index

The Reverse Index Command moves the paper backward one line with no change in horizontal position. This command will not move the print location past the top of the current form and is valid only in Character Mode. The Reverse Index escape sequence is:

ESC M

1B 4D

Example:

Input: A Output: D

C B A

After the final LF, the print position would be on this line at the left margin.

ESCMBESCMCESCMDCRLFLFLFLF

Partial Line Advance

The Partial Line Advance Command moves the paper up or down a partial line for use in superscripting and subscripting. A parameter of 0 moves the paper up; 1 moves the paper down.

ESC [ n Sp p

1B 5B 20 70

IGP for Dot Matrix Printers User Guide

VFU Channel Commands

After the VFU Memory is loaded, the format is set. To use the VFU Format, you must select VFU Mode on the printer. After selecting VFU Mode, you can send VFU Channel Commands to move the paper either forward or backward to the desired location. All reverse moves stop at the TOF if the requested channel is not found. The escape sequence for moving the paper to a desired channel is:

ESC [ c nn ! p

1B 5B 63 21 70

Where:

c = Paper motion direction. 0 = forward paper motion. 9 = reverse paper motion.

nn = VFU channel to which the paper will move. The value for each

channel is shown below:

Channel ASCII HEX

1 00 3030 2 01 3031 3 02 3032 4 03 3033 5 04 3034 6 05 3035 7 06 3036 8 07 3037

9 08 3038 10 09 3039 11 10 3130 12 11 3131

Figure 11 – VFU Channel Values

The following examples give the format for forward and backward moves. Example 1:

To move the paper forward (c = 0) to channel 4 (nn = 03), the escape sequence is:

ESC [ 0 0 3 ! p

1B 5B 30 30 33 21 70

Example 2:

To move the paper backward (c = 9) to channel 1 (nn = 00), the escape sequence is:

ESC [ 9 0 0 ! p

1B 5B 39 30 30 21 70

Chapter 2: Emulations

Plot Mode

When Plot Mode is selected, all input data is treated as plotting data. All graphics in Plot Mode are designed and printed one dot-row at a time.

In Plot Mode the data stream dictates each dot to be printed. Data bytes are either bit images of the dots to be printed, or they are commands to repeat the previous bit image one or more times. Both the density of dots in the horizontal row, and the density of rows can be varied.

When switching from Character Printing to Plot Mode and vice versa, any data in the print buffer is printed. After the data prints out in Character Mode, the print position moves to the left margin of the current line. In Plot Mode it stays at the current dot row. If no paper motion command is issued, printing continues at the current print position.

When the printer enters Plot Mode, it starts plotting at the left margin, at the top row of the character dot matrix. When the printer exits Plot Mode, the position of the next print location depends on the setting of the ModPlot Parameter.

Plot Mode Commands

In Plot Mode, all control codes and escape sequences may be used. All of the commands work the same except the following:

Line Feeds advance by the dot-row instead of line distances. Horizontal Tabs are not recognized. Forward Index commands are not recognized. Reverse Index commands are not recognized.

Entering Plot Mode

To enter Plot Mode, use the escape sequence:

ESC [ < 3 h

1B 5B 3C 33 68 You need to use this escape sequence only once. After entering Plot Mode, you simply send Plot Data, instructions, and the usual control codes and escape sequences.

Exiting Plot Mode

To exit Plot Mode and enter Character Mode, use the escape sequence:

ESC [ < 3 l l = lower-case L

1B 5B 3C 33 6C

When the Modplot Parameter is set to ON, the printer automatically performs an Align to Line Boundary function and moves the print position to the next line down instead of the next dot row down. The default for this parameter is ON. The examples that follow show the actual results of both Modplot ON and Modplot OFF in MT660 Emulation.

IGP for Dot Matrix Printers User Guide

Figure 12 – Alignment Using ModPlot

Align to Line Boundary

When you are exiting from the Plot Mode and the ModPlot Parameter is OFF it is necessary to send an Align to Line Boundary Command to advance the paper to the next line down (as measured from the current TOF). Without this command, characters and graphics would touch. The escape sequence is:

ESC P @

1B 50 40

Chapter 2: Emulations

Plot Data

Two types of information are needed for plot data. The first is an ASCII character (or numerical equivalent in whatever base number system your host requires; octal, decimal, hexadecimal, etc.) that designates which dot pattern you want to print. The second is a one or two byte numeric equivalent (oct., dec., or hex.) of the number of repetitions of the dot pattern you require. This information is converted into the following binary equivalents by the host for transmission to the printer.

Plot Bits

Data 7 6 5 4 3 2 1 0

Dot Pattern Code x 1 d d d d d d

Repeat 1–15 Times x 0 1 0 m m m m

Repeat 16–240 Times x 0 1 1 n n n n

Figure 13 – Plot Data Format

Where:

x = Not used for Plot Data. dddddd = Binary representation of the desired dot pattern.

0 = no dot 1 = dot

mmmm =Binary equivalent of 1–15 repetitions. nnnn = Binary equivalent of 16–240 repetitions in multiples of 16.

A sample Dot Pattern Code is shown below. Six bits represent the dot pattern.

Figure 14 – Sample Dot Pattern Code

IGP for Dot Matrix Printers User Guide

Plot data is received as binary code that represents the dot pattern to be printed, as shown above. If you do not have a table of the various dot patterns possible with their decimal and hexadecimal equivalents, you can use the following method to compute the numeric equivalents.

First, plot out the dot pattern, then convert the six dot pattern to a six-bit binary number (0 for no dot and 1 for a dot). For example:

Figure 15 – Sample Bit Pattern

Now reverse the order of the binary digits. The leftmost dot position (most significant bit) becomes the least significant bit and so on.

101011 D 110101

Convert the new binary number, 110101, to whatever number system you use (octal, decimal, hexadecimal, etc.) to send the code to the printer. The host computer then retranslates the numbers you use back to their binary equivalents for transmission to the printer.

Chapter 2: Emulations

Plotting Dot Patterns

To construct the data code for a specific dot pattern and have the printer print that dot pattern, refer to the table below and perform the procedure that follows.

Figure 16 – Dot Patterns and Identifiers

IGP for Dot Matrix Printers User Guide

Step 1.

Find the desired dot pattern from the two dot pattern columns. For example, use the dot pattern from Figure 16. It is located in the right-hand column (it's the one inside the oval).

Step 2.

Look to the right of the dot pattern and determine the number for this particular dot pattern. In the Figure we have provided the ASCII, Hexadecimal, and Decimal equivalent. Whatever code you use, this number becomes the dot-pattern designator.

Step 3.

Send the Enter Plot Mode escape sequence followed by the dot-pattern designator (ASCII = u), like this:

ESC [ < 3 h u

1B 5B 3C 33 68 75

The desired dot pattern will print one time.

Repeating a Pattern

To repeat a dot pattern, add the desired number of repetitions after the dot-pattern designator. When no repetitions are designated, the printer defaults to 1 and the dot pattern will be printed 1 time. For repetitions of 15 or fewer, the ASCII codes used to designate the number of repetitions begin with Sp (0) and continue through to the / (15).

In the example that follows the table, we show the sequence of actions required to compose an ASCII data code.

Repetitions ASCII Multiples ASCII

1—15 Value Of 16 Value

0 Sp 00 0 1 ! 16 x 1 = 16 1 2 “ 16 x 2 = 32 2 3 # 16 x 3 = 48 3 4 $ 16 x 4 = 64 4 5 % 16 x 5 = 80 5 6 & 16 x 6 = 96 6 7 ' 16 x 7 = 112 7 8 ( 16 x 8 = 128 8

9 ) 16 x 9 = 144 9 10 * 16 x 10 = 160 : 11 + 16 x 11 = 176 ; 12 , 16 x 12 = 192 < 13 – 16 x 13 = 208 = 14 . 16 x 14 = 224 > 15 / 16 x 15 = 240 ?

Figure 17 – Repetition Conversion Table

Chapter 2: Emulations

For example, if you wanted to print a pattern 10 times you would look up 10 in the repetition column above; the ASCII character that corresponds to 10 is an asterisk (*). Therefore, placing an asterisk after a dot-pattern designator would cause the printer to repeat the pattern 10 times.

For numbers greater than 15, you must send a two-byte code:

Byte 1 = (the remainder of the number of desired repetitions) Byte 2 = (number of desired repetitions)

— (largest possible multiple of 16

The maximum number of times a dot pattern may be repeated per request is 255. The ASCII characters that are used to represent multiples of 16 are 0–? (HEX 30–3F).

Example:

To send 70 repetitions, you must first find the largest multiple of 16 that is less than or equal to 70, then subtract that number from 70 to find the remainder. From the above table you can see that the largest multiple of 16 that is less than or equal to 70 is 64. Subtracting 64 from 70 gives us a result of 6. To find the ASCII equivalent of 6, use Figure 17. To compile the 2-byte code for 70 repetitions, remember, the remainder comes first. The result will be & for the remainder of 6, followed by 4 for the multiple of 16 (64).

To print the previous dot pattern 70 times you would send the following escape sequence:

ESC [ < 3 h u & 4

1B 5B 3C 33 68 75 26 34

Stringing Commands Together

Different dot-pattern designators may be strung together in a single escape sequence to enable printing special graphics. To illustrate stringing designators together, we will use a single dotpattern command repeated eight times and string together 6 of these commands. That escape sequence is:

that will result in a positive integer or 0)

÷ 16

ESC [<3h A ( A ( A ( A ( A ( A ( CRLF

1B5B3C3368 41 28 41 28 41 28 41 28 41 28 41 28 0D0A

Where:

A = The dot pattern. ( = 8 repetitions of the dot pattern. (se Figure 17)

This would result in the selected dot pattern being printed 48 times across the page. Or you may send just a single command that specifies that the selected dot pattern is to be printed 48 times:

ESC [ < 3 h A SP 3 CR LF

1B 5B 3C 33 68 41 20 33 0D 0A

IGP for Dot Matrix Printers User Guide

The second escape sequence format is more economical and easier to use when stringing commands together, but either of the above commands would result in a horizontal line of 48 dots across the page.

Repeating either of the above command/CRLF sequences would cause printing of vertical bars across the page. For example, repeating either of the above sequences 100 times would result in:

The advantage of being able to string commands together is that it enables you to put commands for different dot patterns together in one escape sequence for designing special graphics to be printed on your printer. In the next example, the plot density has been set to 60 DPI by 60 DPI in order to show the dot pattern clearly. Sending the following escape sequence 20 times,

ESC[<3hA$1 will result in the following graphic:

CRLFB$1CRLFD$1CRLFH$1CRLFP$1CRLF`$1CRLF

Chapter 2: Emulations

Plot Density

In Plot Mode, your printer will print in a variety of dot densities, both horizontally and vertically. The default density in Plot Mode is 100 dots per inch (DPI) in both the horizontal and vertical directions. To select a different density, use the escape sequence:

ESC [ n1 ; n2 ! q

1B 5B 3B 21 71

Where:

= Horizontal density in DPI in the range of 40 to 240, scaled to 180 DPI.

= Vertical density in DPI in the range of 40 to 240, scaled to 180 DPI.

When you change the plot densities, they remain active until the printer is turned off or they are changed again.

To determine the number of dot patterns necessary to print a full line, multiply the line length by the horizontal DPI, then divide the total by 6 (each dot pattern = 6 bits).

Example:

If line length = 13.2" and DPI = 100, then

Total dots per line = 13.2 x 100=1320, and Total dot patterns per line = 1320/6 = 220

Therefore, to print a full 13.2 inch line at 100 DPI you would have to send 220 dot patterns.

Shading effects can be created by printing different dot patterns in subsequent rows.

IGP for Dot Matrix Printers User Guide

Paper Path Selection

The following commands are used to select the paper input for your T3116 printer. Some of these capabilities may require the purchase of optional components.

Select Tractor 1

ESC [ 5 {

1B 5B 35 7B

Select Tractor 2

ESC [ 6 {

1B 5B 36 7B

Select Tractor 3

Requires the “2T” model.

ESC [ 7 {

1B 5B 37 7B

Select Single Sheet Feeder

ESC [ 0 {

1B 5B 30 7B

Select Auto Sheet Feeder Bin 1

ESC [ 2 1 {

1B 5B 32 31 7B

Select Auto Sheet Feeder Bin 2

ESC [ 2 2 {

1B 5B 32 32 7B

Chapter 2: Emulations

Postal Bar Code Printing

POSTNET Bar Codes

POSTNET Bar Code Mode allows you to make use of the mail handling systems that the United States Postal Service (USPS) has implemented. In addition, POSTNET Bar Codes allow you to take advantage of postal discounts available through USPS for mail pieces using POSTNET Bar Codes for regular 5 digit, Zip+4, and Advanced Bar Code (ABC) zip codes. The basic sequence is:

ESC P b data

1B 50 62 data

After entering POSTNET Mode, any ASCII characters can be sent. However, only the characters 0–9 will be printed. All others, except the reserved control codes and the Space character (Hex

20) are ignored. All reserved control codes, except the ESC (HEX 1B) and the HT (HEX 09) control codes, cancel POSTNET Mode. After POSTNET Mode is canceled, the printer will perform the requested function, such as Line Feed or Form Feed.

The Space character can be used to space between bar codes. If placed inside a bar code, it will terminate the current bar code and cause the framing bar to print. Then the cursor will move the equivalent of one space. Additional spaces can be sent and the cursor position will move the requested number of spaces, then another bar code can be printed. Use the Space character between bar codes only.

The ESC Control Code is used in some applications to select different parameters while in POSTNET Mode.

The HT Control Code is used while in POSTNET Mode to control horizontal space between bar codes. To use the HT Control Code, the procedure is:

If you are NOT going to use the Default Tabs, begin here:

Clear all current Horizontal Tab settings. Set desired Horizontal Tabs.

If you ARE going to use the Default Tabs, begin here:

3. Enter POSTNET Mode.

4. Send data + HT....data + HT....

5. Exit POSTNET Mode.

Example:

ESC P b 9 9 9 9 9 HT 9 8 9 8 9 CR

1B 50 62 39 39 39 39 39 09 39 38 39 38 39 0D

The above sequence would cause bar codes representing the digits 99999 and 98989 to print on the same line, spaced at whatever distance the Horizontal Tabs designate, then the printer would exit the POSTNET Mode.

IGP for Dot Matrix Printers User Guide

Four-State Bar Codes

Four-State Bar Codes are similar to POSTNET bar codes, except they have four states instead of two. In addition to the tall bar and short bare, there is an ascending bar and a descending bar. Four-state bar codes are supported for the UK Postal Service and the Dutch Postal Service.

The syntax for the UK Postal Service Four-State Bar code is:

ESC P c data

1B 50 63 data

The syntax for the Dutch Postal Service KIX Bar code is:

ESC P d data

1B 50 64 data

Once in the Four-State Bar Code Mode, the rules are the same as those described in POSTNET Mode, above.

PLANET Bar Codes

PLANET is similar to POSTNET in "look and feel", and is intended to complement the use of POSTNET for mass mailers. For more information, see the PLANET Bar Code website,

http://www.planetcodes.com/

. The escape sequence for printing PLANET bar codes is:

ESC P f data

1B 50 66 data

Once in the PLANET Bar Code Mode, the rules are the same as those described in POSTNET Mode, above.

Chapter 2: Emulations

Miscellaneous Functions

Reset Printer to Powerup Settings

You can reset the printer to all its powerup settings by sending the escape sequence:

ESC [ 6 ~

1B 5B 36 7E

Alternate Escape Sequences

Since some systems will not allow ESC (1B hex) to be sent as the escape function, you can substitute the following codes:

^ CR OR ^ CR LF

5E 0D 5E 0D 0A

But they must be placed in Column 1 (the left margin), and Alt ESC must be set to ENABLED through the control panel (see the Codes Category of the Configuration Menu).

Emulation and Configuration Switching

In addition to being able to change emulations or configurations through the printer control panel, you can use this escape sequence to change emulations or configurations from your host computer.

~ = tilde

Unlike changing emulations through the control panel, when this escape sequence is used to change emulations, it does not change the Powerup or Alternate configurations that are currently loaded on the printer. The only configuration that is affected is the Current Configuration. The basic switching sequence is:

ESC [ < n h

1B 5B 3C 68

Where:

n = One of the selections from the list below.

10 = Powerup Emulation 13 = Epson Emulation 14 = MT660 Emulation 15 = IBM Proprinter Emulation 16 = Genicom ANSI 18 = HP 2564C Emulation 20 = WinEmul 30 = Config 1 31 = Config 2 32 = Config 3

IGP for Dot Matrix Printers User Guide

Reserved Control Codes

In this emulation there are different combinations of reserved control codes you may use to control various aspects of printer operations. In addition, there are reserved control codes that are used "behind the scenes" in communication between the host computer and the printer, and in data handling protocols.

The table below lists the codes for the MT660 Emulation. In addition, we show in which interface they are valid and give a basic explanation of their function.

Interface Key:

S = Serial C = IEEE 1284

In the Serial and IEEE 1284 interfaces, when an invalid control code is received, it is discarded.

ASCII Interface Function

ETX* S Signals the End of Text to the Printer.

ENQ* S Enquiry code sent by the computer to the printer.

ACK* S Sent by the printer to indicate that there were no errors in the data

transmission.

BEL S, C Sounds printer alarm for .5 seconds.

HT S, C Moves the print position to the next horizontal tab stop.

LF S, C Advances paper one line for printing or one row for plotting (see

also, POPC parameter in Chapter 2, Configuration Menu).

VT S, C Advances paper to the next selected VFU Vertical Tab channel

(see also, POPC parameter in Chapter 2, Configuration Menu).

FF S, C Advances the paper to the top of the next form (see also, POPC

parameter in Chapter 2, Configuration Menu). CR S, C Moves the print position to the left margin of the current line. SO S, C Selects the alternate character set for printing.

SI S, C Selects the primary character set for printing.

DC1*

(XON)

DC3*

(XOFF)

NAK S Printer warns host that there was an error in the data transmission. ESC S, C Tells the printer that the data that follows is not to be printed but is

DEL S, C The Delete Control Code defaults to the Rubout character. It can

S, C When the data buffer is ready to accept more data, XON allows

new data to be sent from the host computer.

S, C XOFF stops data transmission from the host computer when the

data buffer signals it is full.

to be interpreted as a control function.

be used to delete characters in the buffer if your printer is setup

properly. Call your Tech. Rep. for set up procedure.

*Actual function depends on Interface Protocol being used.

Figure 18 – MT660 Control Codes

Chapter 2: Emulations

Escape Sequence Summary

The following escape sequences are supported:

Sequence Function Description

ESC D Index Forward Moves the paper forward one line with no change to the

horizontal position. ESC H Set Tab Sets a tab stop at the current horizontal position. ESC M Index Reverse Moves the paper backward one line with no change to

the horizontal position. ESC P@ Align to Line

Boundary

ESC PA Restore

Cursor Position

ESC PB Save Cursor

Position

ESC PC Save Powerup

Configuration

ESC Pb POSTNET

Mode ESC Pc or ESC Pe ESC Pd

ESC Pf ESC , A

ESC ( xx ESC - A ESC ) xx ESC [ n z Select LPI Selects lines per inch. ESC [ n w Select CPI Selects characters per inch. ESC [ n m Select

ESC [ n t Select Form ESC [ n u Set Tabs Sets horizontal tab stops.

ESC [ n q Clear Tabs Clears horizontal tab stops. ESC [ 3 g Clear All Tabs Clear all tab stops. ESC [ 0 g Clear Current

ESC [ n { Select Paper ESC [ 6 ~ Reset Resets to Powerup Configuration.

ESC [ cn !p VFU Channel ESC [ cn !v Relative Paper

UK Post Mode Causes the following digits to be printed as UK postal

KIX Mode Causes the following digits to be printed as Dutch KIX

PLANET

Mode

Select G0

Character Set

Select G1

Character Set

Attributes

Length

Tab

Path

Command

Motion

Moves the vertical position to the next line relative to top of form as defined by the current LPI setting. Moves the print position to the beginning of the saved vertical position.

Saves the current vertical position. Saves the current configuration into the Powerup

Configuration. Causes the following digits to be printed as POSTNET bar codes.

bar codes. Special for Tally UK. postal bar codes. Special for Tally UK.

Causes the following digits to be printed as PLANET postal bar codes. Selects the G0 character set.

Selects the G1 character set.

Selects bold, italics, overline, strikethrough, underline, subscript and superscript attributes. Also DP, Draft, Gothic, Courier, OCR-A and OCR-B font styles and downloaded font. Select form length. 2 to 255 lines, or 11 inches or 12 inches.

Clear a tab stop at the current horizontal position. Activates the selected paper input path.

Performs a VFU channel move. Performs a relative paper move.

IGP for Dot Matrix Printers User Guide

Sequence Function Description

ESC [ n !s Select

Character

Sets ESC [ n sp B Select

Character

Size ESC [ n1;n2 !q Select Plot

Density ESC [ n “s Set Margins Sets the left and right margins in 1/120ths.

ESC [ n sp p Partial Line Performs a partial (half) line advance up or down. ESC [ f Reverse FF Backs paper up to the previous TOF. ESC [ < 1 h ESC [ < 1 l ESC [ < 2 h ESC [ < 2 l ESC [ < 3 h ESC [ < 3 l ESC [ < n h Emulation &

ESC [ < n sp h Variable Line

VFU

Download

Font

Download

Plot Mode Begins and ends plot mode.

Configuration

Switching

Spacing

Selects the primary (G0) and alternate (G1) fonts and character sets (languages).

Selects the character height and width.

Selects the horizontal and vertical plot densities. Also selects shuttle speed and spacing (speed and spacing options are undocumented).

Begins and ends a VFU download. Begins and ends a font download.

Changes emulations when n = 10 - 39

Sets the line advance distance in 1/720ths.

Figure 19 – MT660 Escape Sequence Summary

Chapter 2: Emulations

IBM Proprinter III XL Emulation

This is an emulation of the IBM Proprinter III XL as defined by IBM document SA34-2065-1, IBM Proprinter III and Proprinter III XL Guide to Operations.

Exceptions

The following escape sequences are not supported:

ESC 8 Disables the paper out sensor. ESC 9 Enables the paper out sensor. ESC < Turns unidirectional mode ON for one line. ESC U Turns unidirectional mode ON. ESC i Immediate mode, prints 1 character at a time. ESC s Half speed mode. ESC = Font Download ESC P Proportional printing

Enhancements

The following enhancements to the Proprinter II XL emulation exist:

Various font styles, plus POSTNET and PLANET bar codes, can be selected with the

ESC x n command:

n (ASCII) n (Hex) Selection

0 00 or 30 Draft 1 01 or 31 Gothic 2 02 or 32 Courier 3 03 or 33 Draft 4 04 or 34 OCR-A 5 05 or 35 OCR-B

@ 10 or 40 POSTNET

C 43 PLANET

There are a number of control panel selections, such as Language, CPI, and LPI, not provided by the emulated printer that can be used in this emulation.

IGP for Dot Matrix Printers User Guide

Epson FX-1180 Emulation

This emulation is defined in the Epson ESC/P Reference Manual. The version of the manual used for the emulation development was dated December 1997.

Exceptions

1. Printing & Sensors Any commands related to unidirectional or single-pass printing, or disabling of sensors, are not supported.

2.Spacing ESC sp n – Variable intercharacter spacing – Not supported.

3. Proportional Spacing ESC p n – Not supported.

4. Font Selection: ESC k – Select Typeface (0 = Courier; 1 = Gothic)

ESC t and ESC ( t – Select Character Set

Supported Epson Character Sets

ISO8859-1 (Latin 1) Latin 1 8859-1 Abicomp OCR-B OCR-B BRASCII PC437 (US) Code Page 437 Bulgaria PC850 (Multilingual) Code Page 850 Code MJK (CSFR) PC863 (Canada-French) Code Page 863 Estonia Roman 8 Roman-8 Hebrew 7, Hebrew 8 ISCII KU42, TIS11, TIS13, TIS16, TIS17, TIS18, TSM/WIN (Thai) MAZOWIA (Poland) PC708 PC720 PC774 (Lithuania) PC853 (Turkish) PC860 (Portugal) PC861 (Iceland) PC862 (Hebrew) PC864 (Arabic),

PC865 (Norway) PC Aptec ISO8859-2 (Latin 2) ISO8859-7 (Latin/Greek) ISO Latin 1 ISO Latin 1T (Turkish) ISO Latin 7 (Greek) PC437 Greek PC851 (Greek) PC852 (East Europe) PC855 (Cyrillic) PC857 (Turkish) PC866 (Russian)

Tally Equivalent Character Sets

Unsupported Epson Character Sets

PCAR864

Figure 20 – FX-1180 Supported Character Sets

Chapter 2: Emulations

Enhancements

The following enhancements to the Epson FX-1180 emulation exist:

1. Various font styles, plus POSTNET and PLANET bar codes, can be selected with the

ESC x n command:

n (ASCII) n (Hex) Selection

0 00 or 30 Draft 1 01 or 31 Gothic 2 02 or 32 Courier 3 03 or 33 Draft 4 04 or 34 OCR-A 5 05 or 35 OCR-B

@ 10 or 40 POSTNET

C 43 PLANET

2. There are a number of control panel selections, such as Language, CPI, and LPI, not provided by the emulated printer that can be used in this emulation.

IGP for Dot Matrix Printers User Guide

Printronix P6000 Emulation

The Printronix P6000 emulation is defined by P6000 Series Multifunctional Line Printer Pedestal Models, Printronix Part Number 108534-001 REV B. With the exception of one control code (Hex

01), the P6000 emulation is a superset of the P600 emulation. There are no exceptions or enhancements for this emulation.

Chapter 2: Emulations

HP 2564C Emulation

The HP 2564C emulation is defined by HP 256x Printer Family Technical Reference Manual, HP Manual Part No. 02564-90905.

This emulation supports the following HP PCL Level 1, PCL Level 2, some PCL Level 3 commands (mainly in the area of font selection), and PCL extensions unique to line matrix printers. These extensions provide for raster graphics, bar code printing, and VFUs.

Command Description Command Description

ESC E Reset ESC 9 Reset Margins ESC *b<0-1056>W Raster Download ESC *b<0-1056>Y Move Raster Amount

of Lines

ESC *rA Raster Start

Sequence

ESC *rB Raster Stop

Sequence

ESC *r70L Set Horizontal 70 DPI ESC *r120L Set Horizontal 120

ESC *r140L Set Horizontal 140

DPI ESC *r144V Set Vertical 144 CPI ESC &dD Enable Underline ESC &d0D Enable Underline ESC &d@ Disable Underline ESC &k0S Select 10 CPI ESC &k2S Select 16.7 CPI ESC &k4S Select 12 CPI ESC &k8S Set Dbl Size ESC &l1L Enable Perf Skip ESC &l0L Disable Perf Skip ESC (0U Set Primary Lang

ASCII ESC (0@ Set Primary Lang

Default ESC (0E Set Primary Lang

Roman8

ESC *r1A Raster Start

Sequence

ESC *r60L Set Horizontal 60 DPI

DPI

ESC *r72V Set Vertical 72 DPI

ESC (8U Set Primary Lang

Roman8

ESC (0L Set Primary Lang Line

ESC (1E Set Primary Lang UK

ESC (0G Set Primary Lang

German ESC (0D Set Primary Lang

Danish ESC (1K Set Primary Lang

Katakana ESC (0O Set Primary Lang

OCRA

ESC (0F Set Primary Lang

French

ESC (0S Set Primary Lang

Swedish

ESC (0K Set Primary Lang

Japanese

ESC (1O Set Secondary Lang

OCRB

IGP for Dot Matrix Printers User Guide

Command Description Command Description

ESC (s0S Set Primary Attributes

to Upright ESC (s0Q Set Primary font Data

Processing ESC (s-1Q Set Primary font Draft ESC )0@ Set Secondary Lang

ESC )0L Set Secondary Lang

Line ESC )0U Set Secondary Lang

ASCII ESC )0G Set Secondary Lang

German ESC )0D Set Secondary Lang

Danish ESC )1K Set Secondary Lang

Katakana ESC )00 Set Secondary Lang

OCRA ESC )s10H Set Secondary CPI 10 ESC )s12H Set Secondary CPI 12

ESC (s1S Set Primary Attributes

to Italics

ESC (s1Q Set Primary font NLQ

Default

ESC )0E Set Secondary Lang

Roman 8

ESC )1E Set Secondary Lang

ESC )0F Set Secondary Lang

French

ESC )0S Set Secondary Lang

Swedish

ESC )0K Set Secondary Lang

Japanese

ESC )10 Set Secondary Lang

OCRB

ESC )s13.3H Set Secondary CPI

13.3

ESC )s16.7H Set Secondary CPI

16.7

ESC )s1S Set Secondary Italics ESC )s0Q Set Secondary Data

ESC )s1Q Set Secondary NLQ ESC )s-1Q Set Secondary Draft ESC (s<1-9999>.<1-

9999>H ESC *z<0-128>C Bar Column Size ESC *t<0-600>R Set Density ESC &a<1-128>L Set Left Margin ESC *z<0-128>H Select Bar Height ESC &l<0-128>P Set Page Length ESC &a<1-128>M Set Right Margin ESC &l<0-128>F Set Text Length ESC &a<1-128>R Move Absolute Row ESC *z<0-128>Q Select Human

Set Primary CPI ESC &l<0-16>V Do VFU Move

Readable Characters

(in Bar Code)

ESC )s15H Set Secondary CPI 15

ESC )s0S Set Secondary

Upright

Processing

ESC *z<0-128>V Select Bar Code Type

Chapter 2: Emulations

Command Description Command Description

ESC &l<1-256>W VFU Download ESC &l<1-9999>.<1-

9999>D

ESC &a<1-128>C Bar Column ESC *z*Z Get Bar Data

Set LPI

Enhancements

The following escape sequences have been added:

POSTNET bar codes ESC * z 20 V PLANET bar codes ESC * x 23 V

IGP for Dot Matrix Printers User Guide

Genicom ANSI Emulation

The Genicom ANSI emulation is defined by the Genicom 4810 / 4840 Programmer’s Manual, GEK-89025. This emulation supports many standard ANSI escape sequences as well as

extended commands for bar codes and oversize characters. The following escape sequences are supported:

Command Description Command Description

ESC c Reset Printer ESC \ Exit Special Modes ESC K Move Partial Line

Down ESC [p1 a Move Relative

Horizontal Position

Right ESC [p1 e Move Relative Vertical

Position Down

ESC [p1 j Move Relative

Horizontal Position

Left ESC [p1 ‘ Move Absolute

Horizontal Position ESC J Set Vertical Tab at

Current Position

ESC [p1;p2;p3 r Set Form Length, Top

Margin, and Bottom

Margin ESC [p1;p2 s Set Left and Right

Margins ESC [p1;p... u Set Horizontal Tabs ESC [3 g Clear Horizontal Tabs ESC [p1;p... v Set Vertical Tabs ESC [4 g Clear Vertical Tabs ESC [p1;p2 SP B Modify Character Size ESC [p1;p2 SP G Set LPI and CPI ESC [p1;p... m Set Font Style and

Enhancements ESC [0 m Cancel Font

Enhancements ESC [1 m Enable Bold ESC [11 h Set Position Unit

ESC [4 m Enable Underline ESC [20 h Set Line Feed New

ESC L Move Partial Line Up

ESC [p1 d Move Absolute

Vertical Position

ESC [p1;p2 f Move Absolute

Horizontal and Vertical Positions

ESC [p1 k Move Relative Vertical

Position Up

ESC H Set Horizontal Tab at

Current Position

ESC [p1;p... g

ESC [0 g Clear Horizontal Tab

ESC [1 g Clear Vertical Tab at

ESC [p1 x Select Character Set

ESC [p1;p... h Set Mode

Set and Clear Horizontal and Vertical Tabs

at Current Position

Current Position

Mode

Line Mode

Chapter 2: Emulations

Command Description Command Description

ESC [22 m Disable Bold ESC [>1 h Set Proportional Print

Mode

ESC [24 m Disable Underline ESC [>3 h Set C1 Control Code

Mode

ESC [10 m Select Data

Processing Font ESC [11 m Select Data

Processing Font ESC [12 m Select Character

Graphics Font ESC [13 m Select Gothic Font ESC [20 l Reset Line Feed New

ESC [14 m Select Courier Font ESC [>1 l Reset Proportional

ESC [15 m Select Draft Font ESC [>3 l Reset C1 Control

ESC [16 m Select OCR-A Font ESC [>5 l Reset Character Set 2

ESC [17 m Select OCR-B Font ESC P Begin Dot Graphics

ESC [18 m Select Italic Gothic

Font ESC [19 m Select 13.3 CPI

Gothic Font

ESC [>5 h Set Character Set 2

Mode

ESC [p1;p... l Reset Mode

ESC [11 l Reset Position Unit

Mode

Line Mode

Print Mode

Code Mode

Mode

ESC [p1 b Repeat Character

ESC [p1;p2;p3 q Select Horizontal and

Vertical Graphics Dot Densities

ESC ]! Begin EVFU Table

Loading ESC [0 t Select Bar Code

Mode ESC [p1;p...;p10 } Select Bar Code

Parameters ESC [1 | Select Oversize

Character Font (No

Rotation) ESC [3 | Select Oversize

Character Font (180-

Degree Rotation)

ESC [p1 ! p Move to EVFU

Channel

ESC [3 t Deselect Bar Code

Mode

ESC [0 | Exit Oversize Printing

ESC [2 | Select Oversize

Character Font (90Degree Rotation)

ESC [4 | Select Oversize

Character Font (270Degree Rotation)

IGP for Dot Matrix Printers User Guide

Exceptions

The following are discrepancies between the Genicom 4840 printer and Genicom manual:

ESC [p1 d AVM beyond 15840 decipoints is ignored ESC [p1 e RVM uses the decipoint parameter exactly (no round off to 1/144ths)

RVM greater than 15840 decipoints is ignored ESC [p1;p... m p1 = 11 - Data Processing ESC [p1 !p Syntax not ESC[p1;p2 !p ESC [p1;p2;p3 q p3 = 0-4 - ignored

p2 and p3 are not ignored in any p1 mode ESC [p1;p2;p3 r p3 is measured from BOF, not TOF

Differences between the T3116 IGF Option’s Genicom ANSI emulation and the Genicom 4840 printer:

ESC [p1;p... m p1 = 19 - Gothic ESC [p1;p2;p3 q p1 = 0 - 60H x 72V

p1 = 1 - 144H x 72V p1 = 2 - 144H x 144V p3 = 5 - 144H p3 = 8-10 - 72H

ESC Q Self-test command is not supported ESC ] 5 Font download is not supported ESC [p1 SP } Font download control is not supported ESC [ p1;p2 sp G Line heights greater than 9 inches are not supported ESC [ > 1 h Proportional spacing is not supported ESC [p1 x Supported as follows:

p1 = 0 US 1 German 2-3 French 6, 23 Italian 7, 20 UK 8, 24 Spanish 9-10 Norwegian/Danish 11-12 Norwegian/Danish II 13-16 Swedish/Finnish 437 Code Page 437 USA 850 Code Page 850 Multilingual 863 Code Page 863 French Canadian 8575 Roman 8

Latin 1

ESC [p1;p...;p10 } Bar code ratios greater than 85 are not supported

Enhancements

The following escape sequences have been added:

POSTNET bar codes ESC [ 50 ; … } PLANET bar codes ESC [ 53 ; … }

Chapter 2: Emulations

IGP for Dot Matrix Printers User Guide

Graphics Language Emulations

Graphics languages are a set of commands used to create graphic images such as large characters, lines, boxes, and bar codes. A graphics language is run on top of any of the above underlying control language emulations.

QMS Code V Emulation

This graphics language is an emulation of QMS Code V Version 1 and 2. It is accessible from all underlying control languages.

The emulation is based on QMS Manual Number 1720155B, QMS Code V Version II

Programming Manual. The commands are defined in Manual Number 079697, Graphics Applications Manual, Line Printers.

Command Description Inside

Pass

^#n Compressed Fonts ^@Cnn Draft Fonts ^@Hn Dump Mode ^@Lnn Lines Per Inch (LPI) ^[nnn Data Field, Buffered Forms ^A Ignore Data Off ^B^-<data>^] Buffered Formatting, Version 1 ^B{B,N,O,S,T,Y}9x<ratio><data>^G Bar Code Style 1, Horz. Ver. Ratio ^B{B,N,O,S,T,Y}x<data>^G Bar Code Style 1, Horizontal ^Cnn<data>^Z Buffered Form Copy ^C{B,N,O,S,T,Y}9x<ratio><data>^G Bar Code Style 1, Vert Var. Ratio ^C{B,N,O,S,T,Y}x<data>^G Bar Code Style 1, Vertical ^D Descender Mode  ^~Dhhhvvv Pass Density

 

     

 

Outside

Pass



^Dnn Dot Slew ^Ehhwwjjd<data> Graphics Pass, Vertical Left ^F Free Format ^~FF Full Space Font Mode ^~FH Half Space Font Mode ^~FQ Quality Font Mode ^G Command Terminator ^Hnn Form Length ^Hnn Pass Length

 

       



Chapter 2: Emulations

^IBARC,x,R<ratio>,{N,E,B},<data>^G Bar Code Style 2, Var. Ratio

^IBARC,x,{N,E,B},<data>^G Bar Code Style 2 ^IFONT,S,n^G<data> Default Font ^IFORM,C... Buffered Form Create ^IFORM,D<name>^G Buffered Form Delete ^IFORM,E<form name>^G<data>^G Buffered Form Execute ^IFORM,L Buffered Form List ^IFORM,R Buffered Form Memory Reset ^IHEX,nn Hex Command ^ILOGO,nn^G Logos ^Innn Interrupt Function ^IPEXP,h,v^G Pixel Exppansion ^IREPE Repeat Terminator ^IREPH,n,hhd^G Horizontal Repeat, Version 2 ^IREPV,n,vvvd^G Vertical Repeat, Version 2



    

        



^IISO,n^G ISO Character Set ^Jvvd Vertical Justification  ^KF Half-Dot Mode ^KH Half-Tone Toggle  ^KLnn Half-Tone ^Knn Line Slew ^LBhhhdvvvdhv Boxes ^LDhhhdvvvd Dashed Lines ^LFhhhdvvvdhvllldt...^G Form Drawing ^Lnn Form Length ^LShhhdvvvd Solid Lines ^Mhhwwjjd<data> Graphics Pass, Horizontal ^Nx Command Change ^O Free Format Off ^PN Graphics Mode Off ^PY Graphics Mode On

 



   



^Q<plot data>^G Plot Mode ^R Reverse Image Toggle

 

IGP for Dot Matrix Printers User Guide

^R^- Buffered Form Repeat ^Rnnnn^-<data>^-^Z^- Vertical Repeat, Version 1 ^Sn NLQ Fonts ^Snntt^-<data>^-^S^- Horizontal Repeat, Version 1 ^Thhhd Horizontal Tab ^Uhhwwjjd<data> Graphics Pass, Upside Down ^Vhhwwjjd<data> Graphics Pass, Vertical Right ^Wnn Line Slew ^Wnn Pass Width ^X Ignore Data On ^Yx{+,-}z Automatic Increment/Decrement ^Z Buffered Copy/Repeat Terminator ^– Carriage Return (CR) ^* Line Feed (LF) ^, Form Feed (FF)



    



 



Chapter 2: Emulations

Printronix Graphics Language Emulation

The Printronix Graphics Language (PGL) emulation provides a graphics language that is compatible with the Printronix IGP 100/200/400 language. It is accessible from all underlying control languages.

The emulation is based on IGP-100 Firmware Version 2.19A (Part Number 148771,) and the Printronix IGP-100 Manual (Part Number 141331-001 Revision A.) In cases where the function of the firmware differs from the manual, the emulation follows the function of the firmware. The commands are defined in Manual Number 079697, Graphics Applications Manual, Line Printers.

Command Normal

Mode

AFn  Executes the dynamic alphanumeric data

ALPHA

BARCODE

BFn  Executes the dynamic bar code data

BOX

CORNER

Create

Mode



Execute

Mode

Description

provided after the (cc) EXECUTE command.

Defines size, location, and content of

alphanumeric characters and dynamic alphanumeric data fields.

Each bar code type has its own command

to define size, location, orientation, and data as described in the “Bar Codes” chapter.

provided after the (cc)EXECUTE command.

Defines size, location, and thickness of

boxes.

Defines vertical and horizontal length,

location, and thickness of a set of four corners.

CREATE

DELETE FORM

DELETE LOGO

DENSITY

Graphics Language Exceptions

Exceptions from the T6215 implementation are noted below. All unsupported emulation commands are parsed and ignored. All other capabilities, exceptions, and nuances are defined by the Line Printer Graphics Applications Manual.

Exceptions from the T6215 Printer

The human readable attribute of a bar code is not supported above the bar code. Reverse fields do not reverse standard text. PGL – REVERSE Block character patterns and reverse fields are not supported. Control of whether or not descending block characters descend is not supported. All block characters with descending components (i.e. g, j, q, y) will descend below the baseline. The human readable characters of the Code 39 bar code are bounded by asterisks. Check digits are not printed in the human-readable portion of UPC bar codes Long bars are not supported for Code 39 bar codes. PGL, Code V, and Genicom The Industrial 2 of 5 bar code is not supported. PGL, Code V, and Genicom The size vertical bar codes (top to bottom as printed) are slightly smaller due to the printer resolution. Style 2 is not supported by the Vscale control panel option because that block character capability is unavailable. Block character size and position within a cell is slightly different. Multi-high human-readable in a bar code is not supported. Embedded human-readable is only available for UPC and EAN bar codes, and is always on. Block character reverse acts like reverse fields. PGL Dark barcodes and block characters are not supported Items that start before the current paper position are not printed.

Emulations Affected

PGL – BARCODE

Code V - ^KL, ^KH Code V – ^D

PGL, Code V, and Genicom PGL, Code V, and Genicom

PGL, Code V, and Genicom Code V PGL, Code V, and Genicom

PGL PGL

Chapter 3: True Type Fonts

Chapter 3: TrueType Fonts

The “block character” text printed by the Code V and PGL industrial graphics languages is generated using TrueType font outlines. There is one TrueType font embedded in the printer as a resident font used for generating these characters. This font is:

Resident Font Name

MonoBlock Bold 93779

Font Number

Maximum Character Size

The parameters BlkMaxH and BlkMaxV allow to set the maximum size block character horizontally and vertically that will be printed using the TrueType font. Characters above this maximum size will be printed using the previous vector style block characters.

Parameter

BlkMaxH BlkMaxV

Setting options

0 to 136 (Default: 40) 0 to 136 (Default: 40)

IGP for Dot Matrix Printers User Guide

The PGL FONT Command

The FONT command has been added to the PGL emulation contained in the printer to provide increased flexibility and compatibility when printing forms designed for laser printers. This command allows the form designer to choose from a variety of fonts when creating or printing a form. The format of the FONT command is described below.

Mode: NORMAL, CREATE, EXECUTE.

Format: <SFCC>FONT;FACE n

<SFCC> Enter the Special Function Control Character as set in the SFCC menu

option. When in the CREATE mode, do not include the SFCC.

FONT The font command.

FACE n Specifies the typeface. Enter FACE, then a space, then the 5 digit

number of the desired typeface. For the resident font, the following number applies:

93779 –MonoBlock Bold

Notes: The FACE SMODE, BOLD, BLOCK, SLANT, SYMSET, POINT, SPACE, and ZERO

parameters are not currently supported. Use of the FONT command in the Create mode affects only the current form being

created. It will have no effect on other forms or the font used for Normal or Execute mode text. Similarly, use of the FONT command in the Execute and Normal modes does not affect the fonts used in forms that have already been created.

NOTE: Currently download of fonts is not supported.

Chapter 4: Miscellaneous

Driver

This printer model is provided without driver. The IGP printer model basically is delivered with the standard Online CD-Rom.

The Driver located on this CD rom requires MTPL and Epson LQ emulations. These emulations are not included in the firmware of an IGP printer model.

NOTE: However the Plug&Play string is identical to that of the standard

printer this means that the standard driver would be installed by accident. This driver is not functional!

Cutting Device

Basically the optional cutting device will work. As in IGP the form is defined by the “Create” command, and printing is normally done by the

“Execute” command without a formfeed, the form will not be cut using the “Cut on Formfeed” setting. Instead it is recommended to use the “Cut on Tof” setting (See printer's menu: ViewCut).

NOTE: The function "cutting" is not determined as there is no support

from the emulations. Hence we recommend to test the proper function of the cutter in the particular environment.

Standard Documentation

The IGP printer model is provided with its standard printer documentation. It is intended to being used to describe the basic functions of your printer. Only the special IGP

functions which differ from the standard are described in this manual.

IGP for Dot Matrix Printers User Guide

All rights reserved. Translations, reprinting or copying by any means of this manual complete or in part or in any different form requires our explicit approval. We reserve the right to make changes to this manual without notice. All care has been taken to ensure accuracy of information contained in this manual. However, we cannot accept responsibility for any errors or damages resulting from errors or inaccuracies of information herein.

DASCOM REPRESENTATIVES

GERMANY DASCOM Europe GmbH

Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com

SINGAPORE DASCOM AP Pte Ltd

21 Bukit Batok Crescent #29-81, WCEGA Tower Singapore 6580656 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.com

AMERICAS DASCOM Americas Corporation

421 W. Main Street Waynesboro, VA 22980 USA Phone: +1 (877) 434 13 77 www.dascom.com

UNITED KINGDOM DASCOM GB Ltd

Hart House, Priestley Road Basingstoke, Hampshire RG24 9PU, England Phone: +44 (0) 1256 481481 Fax: +44 (0) 1256 481400 www.dascom.com

FRANCE DASCOM Europe GmbH

117 Avenue Victor Hugo 92100 Boulogne-Billancour t France Phone: +33 (1)73 02 51 98 www.dascom.com

Dascom T2250 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Scope

Chapter 1: Control Panel

Basic Elements

Menu Structure

Menu Parameters

Menu Printout Example

Advanced Menu

PJL Functions

Chapter 2: Emulations

MT660 Emulation

Character Definition and Format

Attributes, Print Position, and Type Styles

Combining Attributes

Languages and Character Sets

Primary and Secondary Fonts and Languages

Selecting Primary and Secondary Sets

Characters Per Inch

Character Height and CPI

Page Formatting

Lines Per Inch

Variable Line Spacing

Horizontal Tabs

Setting Tabs

Current Position

Clearing Tabs

Clearing All Horizontal Tabs

Clearing Current Horizontal Tab

Setting Left and Right Margins

Setting Vertical Format

Form Length Select

VFU Download Commands

VFU Load

VFU Load Errors

VFU Data Format

Paper and Print Position Movement

Reserved Control Codes

Horizontal Tab HT 09

Vertical Tab VT 0B

Carriage Return CR 0D

Line Feed LF 0A

Save Print Position

Restore Vertical Print Position

Relative Paper Motion

Reverse Form Feed

Forward Index

Reverse Index

Partial Line Advance

VFU Channel Commands

Plot Mode

Plot Mode Commands

Entering Plot Mode

Exiting Plot Mode

Align to Line Boundary

Plot Data

Plotting Dot Patterns

Repeating a Pattern

Stringing Commands Together

Plot Density

Paper Path Selection

Select Tractor 1

Select Tractor 2

Select Tractor 3

Select Single Sheet Feeder

Select Auto Sheet Feeder Bin 1

Select Auto Sheet Feeder Bin 2

Postal Bar Code Printing

POSTNET Bar Codes

Four-State Bar Codes

PLANET Bar Codes

Miscellaneous Functions

Reset Printer to Powerup Settings

Alternate Escape Sequences

Emulation and Configuration Switching

Reserved Control Codes

Escape Sequence Summary

IBM Proprinter III XL Emulation