S/M No. :
Service Manual
Microwave Oven
Model: KOR-6L3B3S
KOR-6L3B3W
Caution
: In this Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service Information Center (http://svc.dwe.co.kr).
Dec. 2010
Downloaded from www.Manualslib.com manuals search engine
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a)Do not operate or allow the oven to be operated with the door open.
(b)Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) Interlock operation, (2) Proper door closing, (3) Seal and sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and latches, (5) Evidence of dropping or abuse.
(c)Before turning on power to the microwave oven for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections.
(d)Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.
(e)A microwave leakage check to verify compliance with the federal performance standard should be performed on each oven prior to release to the owner.
TABLE OF CONTENTS |
|
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE |
|
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY...................................................................................................... |
1 |
SAFETY AND PRECAUTIONS ........................................................................................................................................... |
2 |
1. FOR SAFE OPERATION .................................................................................................................................. |
2 |
2. FOR SAFE SERVICE PROCEDURES ............................................................................................................. |
2 |
SPECIFICATIONS ............................................................................................................................................................... |
3 |
EXTERNAL VIEW................................................................................................................................................................ |
4 |
1. OUTER DIMENSION......................................................................................................................................... |
4 |
2. FEATURES DIAGRAM...................................................................................................................................... |
5 |
3. CONTROL PANEL ............................................................................................................................................ |
6 |
INSTALLATION................................................................................................................................................................... |
7 |
OPERATIONS AND FUNCTIONS....................................................................................................................................... |
8 |
DISASSEMBLY AND ASSEMBLY...................................................................................................................................... |
9 |
INTERLOCK MECHANISM AND ADJUSTMENT............................................................................................................. |
16 |
TROUBLESHOOTING GUIDE .......................................................................................................................................... |
17 |
MEASUREMENT AND TEST ............................................................................................................................................ |
21 |
1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT ........................................................................ |
21 |
2. MICROWAVE RADIATION TEST ................................................................................................................... |
22 |
3. COMPONENT TEST PROCEDURE ............................................................................................................... |
23 |
WIRING DIAGRAM............................................................................................................................................................ |
24 |
PRINTED CIRCUIT BOARD.............................................................................................................................................. |
25 |
1. CIRCUIT CHECK PROCEDURE .................................................................................................................... |
25 |
2. PCB CIRCUIT DIAGRAM................................................................................................................................ |
28 |
3. P.C.B. LOCATION NO .................................................................................................................................... |
29 |
EXPLODED VIEW AND PARTS LIST............................................................................................................................... |
30 |
1. DOOR ASSEMBLY ......................................................................................................................................... |
30 |
2. CONTROL PANEL ASSEMBLY...................................................................................................................... |
30 |
3. TOTAL ASSEMBLY......................................................................................................................................... |
30 |
1
Downloaded from www.Manualslib.com manuals search engine
SAFETY AND PRECAUTIONS
1. FOR SAFE OPERATION
Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may cause serious bodily injury to the operator.
IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE. (Only a trained service personnel should make repairs.)
(1)A broken door hinge.
(2)A broken door viewing screen.
(3)A broken front panel, oven cavity.
(4)A loosened door lock.
(5)A broken door lock.
The door gasket plate and oven cavity surface should be kept clean.
No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven. DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN.
The microwave oven has concealed switches to make sure the power is turned off when the door is opened. Do not attempt to defeat them.
DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.
2.FOR SAFE SERVICE PROCEDURES
1.If the oven is operative prior to servicing, a microwave emission check should be performed prior to servicing the oven.
2.If any certified oven unit is found to servicing, a microwave emission check should be performed prior to servicing the oven.
(a)inform the manufacturer, importer or assembler,
(b)repair the unit at no cost to the owner,
(c)attempt to ascertain the cause of the excessive leakage,
(d)tell the owner of the unit not to use the unit until the oven has been brought into compliance.
3.If the oven operates with the door open, the service person should tell the user not to operate the oven and contact the manufacturer and the dealer immediately.
IMPORTANT
The wire in this mains lead colored in accordance with the following code.
Green-and-yellow : Earth
Blue |
: Neutral |
Brown |
: Live |
As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows.
The wire which is colored green-and-yellow must be connected to the terminal in the plug which is marked with the letter ‘E’, earth symbol or colored green-and-yellow.
The wire which is colored blue must be connected to the terminal which is marked with the letter ‘N’ or colored black.
The wire which is colored brown must be connected to the terminal which is marked with the letter ‘L’ or colored red.
NOTE :
The oven is designed for counter-top use only.
2
Downloaded from www.Manualslib.com manuals search engine
SPECIFICATIONS
POWER SUPPLY |
|
220~240V AC, 50Hz SINGLE PHASE WITH |
|
|
|
|
EARTHING |
|
|
|
|
|
|
INPUT POWER |
1000 W |
|
|
|
|
MICROWAVE |
|
ENERGY OUTPUT |
700 W |
|
|
|
|
|
|
FREQUENCY |
2,450 MHz |
|
|
|
|
OUTSIDE DIMENSIONS (W x H x D) |
446 x 270 x 319 mm |
||
|
|
|
|
CAVITY DIMENSIONS (W x H x D) |
295 x 219 x 303 mm |
||
|
|
|
|
CAVITY VOLUME |
|
20 L |
|
|
|
|
|
NET WEIGHT |
|
APPROX. 10.2 Kg |
|
|
|
|
|
TIMER |
|
59 min. 90 sec. |
|
|
|
|
|
POWER SELECTIONS |
10 Levels |
||
|
|
|
|
* Specifications are subject to change without notice.
3
Downloaded from www.Manualslib.com manuals search engine
EXTERNAL VIEW
1. OUTER DIMENSION
446 |
|
|
|
|
319 |
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
270
4
Downloaded from www.Manualslib.com manuals search engine
2. FEATURES DIAGRAM
1 |
2 |
|
3 |
4 |
9 |
0 |
q |
|
8 |
7 |
6 |
5 |
|
w |
|
1Door latch - When the door is closed, it will automatically shut off. If the door is opened while the oven is operating, the magnetron will automatically shut off.
2Door seal - The door seal surfaces prevent microwaves escaping from the oven cavity.
3Oven cavity
4Control panel
5Door open button - To open the door push the door open button.
6Coupler - This fits over the shaft in the center of the oven cavity floor. This is to remain in the oven for all cooking.
7Roller guide - This must always be used for cooking together with the glass cooking tray.
8Glass cooking tray - Made of special heat resistant glass. The tray must always be in proper position before operating. Do not cook food directly on the tray.
9Viewing screen - Allows viewing of food.
The screen is designed so that light can pass through, but not the microwave.
0Waveguide cover - Protects the microwave outlet from splashes of cooking foods.
qSafety interlock system
wOven lamp - Automatically turns on during oven operating.
5
Downloaded from www.Manualslib.com manuals search engine
3. CONTROL PANEL
|
1 |
|
2 |
4 |
5 |
3 |
|
|
6 |
|
7 |
8 |
9 |
1DISPLAY - Cooking time, power level, indicators and the current time are displayed.
2AUTO COOK - Used to cook or reheat many of favorite food.
3DEFROST - Used to defrost foods for time and weight.
4POWER - Used to set power level.
5CLOCK - Used to set clock.
6ONE TOUCH COOK - Used to cook or reheat specific quantities of food.
7TIME SET PAD - Used to set the cooking time and the current time.
8STOP/CLEAR - Used to stop the oven operation or to delete the cooking data.
9START/+30 SEC - Used to start the oven and also used to set a reheat time.
6
Downloaded from www.Manualslib.com manuals search engine
INSTALLATION
1.Steady, flat location
This microwave oven should be set on a steady, flat surface. This microwave oven is designed for counter top use only.
2.Leave space behind and side
All air vents should be kept a clearance. If all vents are covered during operation, the oven may overheat and, eventually, cause failure.
3.Away from radio, and TV sets
Poor television reception and radio interference may result if the oven is located close to a TV, radio, antenna, or feeder and so on. Position the oven as far from them as possible.
4.Away from heating appliances and water taps
Keep the oven away from hot air, steam and splash when choosing a place to position it, or the insulation might be adversely affected and breakdowns occur.
5.Power supply
• Check your local power source.
This microwave oven requires a current of approximately 10 amperes, 230 Volts, 50 Hz.
•Power supply cord is about 0.8 meters long.
•Used the voltage must be the same as specified on this oven. Using a higher voltage may result in a fire or other accident causing oven damage. Using low voltage will cause slow cooking. We are not responsible for damage resulting from use of this oven with a voltage of ampere fuse other than those specified.
•This appliance is supplied with cable of special type, which, if damaged, must be repaired with cable of same type. Such a cable can be purchased from DAEWOO and must be installed by a qualified person.
6.Examine the oven after unpacking for any damage such as:
A misaligned door, broken door or a dent in cavity.
If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.
7.Do not operate the oven if it is colder than room temperature
(This may occur during delivery in cold weather.) Allow the oven to become room temperature before operating.
EARTHING INSTRUCTIONS
This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of the electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a earthing plug. The plug must be plugged into an outlet that is properly installed and earthed.
WARNING
Improper use of the earthing plug can result in a risk of electric shock. Consult a qualified electrician or service-man if the earthing instructions are not completely understood, or if doubt exists as to whether the appliance is properly earthed, and either : If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade earthing plug, and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the extension cord should be equal to or greater than the electrical rating of the appliance, or DO NOT USE an extension cord.
7
Downloaded from www.Manualslib.com manuals search engine
OPERATIONS AND FUNCTIONS
11. Connect the mains lead to an electrical outlet.
12. After placing the food in a suitable container, open the oven door and put it on the glass tray. The glass tray must always be in place during cooking.
13. Close the door securely.
14. The oven door can be opened at any time during operation by pushing the door open button on the control panel. The oven will automatically shut off. To restart the oven, close the door and then touch the START pad.
15. Each time a pad is touched. a BEEP will sound to acknowledge the touch. 16. The oven automatically cooks on full power unless set to a lower power level. 17. The display will show “: 0” when the oven is plugged in.
18. Time clock returns to the present time when the cooking time ends.
19. When the STOP/CLEAR pad is touched during the oven operation, the oven stops cooking and all information retained. To erase all information (except the present time), touch the STOP/CLEAR pad once more. If the oven door is opened during the oven operation, all information is retained.
10.If the START pad is touched and the oven does not operate, check the area between the door and door is closed securely. The oven will not start cooking under the door is completely closed or the program has been reset.
Make sure the oven is properly installed and plugged into the electrical.
Wattage output chart
The power level is set by touching the POWER pad. The chart shows the display, the power level and the percentage of power.
Touch the POWER Pad |
Power Level(Display) |
Approximate Percentage of Power |
Once |
P-HI |
100% |
|
|
|
Twice |
P-90 |
90% |
|
|
|
3 times |
P-80 |
80% |
|
|
|
4 times |
P-70 |
70% |
|
|
|
5 times |
P-60 |
60% |
|
|
|
6 times |
P-50 |
50% |
|
|
|
7 times |
P-40 |
40% |
|
|
|
8 times |
P-30 |
30% |
|
|
|
9 times |
P-20 |
20% |
|
|
|
10 times |
P-10 |
10% |
|
|
|
11 times |
P-00 |
00% |
|
|
|
8
Downloaded from www.Manualslib.com manuals search engine
DISASSEMBLY AND ASSEMBLY
Cautions to be observed when troubleshooting.
Unlike many other appliances, the microwave oven is high-voltage, high-current equipment. It is completely safe during normal operation.
However, carelessness in servicing the oven can result in an electric shock or possible danger from a short circuit. You are asked to observe the following precautions carefully.
1.Always remove the power plug from the outlet before servicing.
2.Use an insulated screwdriver and ware rubber gloves when servicing the high voltage side.
3.Discharge the high voltage capacitor before touching any oven components or wiring.
(1)Check the grounding.
Do not operate on a two-wire extension cord.
The microwave oven is designed to be used while earthed. It is imperative, therefore, to make sure it is earthed properly before beginning repair work.
(2)Warning about the electric charge in the high voltage capacitor.
For about 30 seconds after the operation stopped and electric charge remains in the high voltage capacitor.
When replacing or checking parts, short between oven chassis and the negative high terminal of the high voltage capacitor by using a properly insulated screwdriver to discharge.
4.When the 10A fuse is blown out due to the operation of the monitor switch; replace primary interlock switch, secondary interlock switch and
interlock monitor switch.
5.After repair or replacement of parts, make sure that the screws are properly tightened, and all electrical connections are tightened.
6.Do not operate without cabinet.
CAUTION : Service personnel should remove their watches whenever working close to or replacing the magnetron.
WARNING : When servicing the appliance, need a care of touching or replacing high potential parts because of electrical shock or exposing microwave. These parts are as follows - HV Transformer, Magnetron, HV Capacitor, HV Diode, HV fuse.
9
Downloaded from www.Manualslib.com manuals search engine
1.To remove cabinet
1)Remove four screws on cabinet back.
2)Pull the cabinet backward.
2.To remove door assembly
1)Remove two screws which secure the stopper hinge top.
2)Remove the door assembly from top plate of cavity.
3)Reverse the above for reassembly.
NOTE : After replacing the door assembly, perform a check of correct alignment with the hinge and cavity front plate.
10
Downloaded from www.Manualslib.com manuals search engine
Loading...