OPERATOR’S MANUAL
R
53-in 8 Drawer bb WORKstation model # 31011
service parts
Call 1-800-366-7278 for Service Parts. Refer to Service Parts Drawing for full listing of Service Parts.
Locating Model # Information
Model numbers and other information required for service parts is located on a label on the interior right side of the top most drawer.
capacities
•The maximum weight for each drawer should be no more than 25 lbs.
•Empty weight of the unit is 166 lbs.
•The maximum product weight, including contents, should be no more than 500 lbs.
maintenance
•For casters, use high quality bearing grease, (yearly).
•Lubricate the slides with grease or equivalent,(twice yearly.)
• Lubricate lock with graphite, (yearly).
Ball bearing slides |
Friction slides |
•Periodically the drawer fronts, drawer trim, and other surfaces should be cleaned with a mild detergent and water.
•Auto wax will preserve the unit’s luster finish. Apply the wax as to a car. The wax will also help protect the unit against scratches.
•Grease and oil can be removed with most standard
cleaning fluids. For safety, use a nonflammable cleaning fluid.
•If drawer liners are supplied, it is recommended they are used to protect the finish inside the drawers and to make the drawers easier to clean. The drawer liners may be cleaned
with soap and water.
|
safety |
DANGER |
is used to indicate a hazardous situation which, |
if not avoided, will result in serious injury or death. |
|
WARNING |
indicates a hazardous situation which, |
if not avoided, could result in serious injury or death. Caution is used to indicate a hazardous situation which, if not avoided, may result in minor injury, moderate injury, or property damage.
CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
danger
•DO NOT stand on this product. You may fall or cause product to tip.
•DO NOT open more than one drawer. The product may become unstable and tip.
•DO NOT step in the drawers. You may fall or cause product to tip.
•DO NOT mount this product on a truck bed or any other moving object.
•DO NOT move the product prior to closing
and locking all the drawers. The drawers could come open and make the product unstable and tip.
warning
•WEAR SAFETY GLASSES when removing or repositioning the slides.
•DO NOT pull the unit, push it when moving
•USE THE BRAKES when not moving this product. This will prevent the product from rolling.
•DO NOT alter this product in any manner. For example, do not weld external lockbars or attach electrical equipment.
•Keep the product on level surfaces. The product may become unstable and tip if stored or moved on an uneven surface.
•BE CAREFUL when closing the cover. Remove hands before the cover closes completely.
caution
•This product is not designed to be directly lifted with a fork lift, or to be towed with any mechanical devices.
•The maximum weight for each drawer should never be exceeded.
•Only transport this product empty. Properly secure when transporting.
•DO NOT exceed maximum product weight, including contents. See Capacities for more information.
Distributed by Sears Brands Management Corporation, Hoffman Estates, IL 60179 |
Rev. A F1873 |
hardware
TOOLS REQUIRED:
3/8-in wrench
Hardware Included:
1/4 - 20 x 5/8-in (Qty: 16)
1/4 - 20 Nut (Qty: 16)
Carton Contents
Cabinet:
Literature
Caster pack
Caster pack
ASSEMBLY
Note: Not all assembly instructions will relate to your model.
REMOVING DRAWERS
•Empty the drawer.
•Fully extend the drawer.
Release
Lever Style - Lift or lower (depending on the slide) the release lever on both sides, (this allows the slides to ride over the stops.) Pull out to remove.
Tab Style - Depress the release tabs on both sides, (this allows the slides to ride over the stops.)
Pull out to remove.
2
Friction Style - Fully extend the drawer. Insert screwdriver into the slot in the side and push in on the stop until it clears the lance. Pull drawer just past lance before releasing stop. Repeat the process for the other slide.
CASTER INSTALLATION
Items Needed:
1/4 - 20 x 5/8-in (Qty: 16) 1/4 - 20 Nut (Qty: 16) 3/8-in Wrench
Process:
•Remove bottom drawers.
•Lay the cabinet on its back. Use packaging material to protect the finish.
•Mount both swivel casters on the same side of the unit.
•Attach the casters using four screws and nuts per caster.
•Wrench tighten all screws. It is recommended not to exceed 80 inch pounds of torque.
•Return the unit to its upright position.
•Reinstall bottom drawers (see step 3).
Nut
Screw
installING drawers
Ball bearing slide - Pull slides and slide carrier out to fully extended position (see illustration.) Hold the slide on the cabinet while aligning it with the slide on drawer. Slightly insert one side and repeat for the other side. Slowly push drawer to its fully closed position to engage slide. Open drawer and reclose to ensure proper operation.
slide carrier
slide
3