Comelit FT SK9010 User Manual [en, es, fr]

FT SK9010

Comelit Group S.p.A. - Via Don Arrigoni 5 - 24020 Rovetta S. Lorenzo BG Italy - tel. [phone] - fax [phone]
www.comelit.eu www.simplehome.eu [e-mail] [e-mail] [e-mail]

Assistenza tecnica Italia 0346/750090 Technical service abroad ([phone]
Commerciale Italia 0346/750091 Export department ([phone]

TECHNICAL

SHEET

FEUILLE

TECHNIQUE

EN FR

TECHNISCHE

HANDLEIDING

HOJA

TÉCNICA

NL ES

Centrale met radio-ontvanger Art. SK9010

Centralita con receptor radio art. SK9010

Control unit with RF receiver Art. SK9010

Centrale avec récepteur radio Art. SK9010

GROUP S.P.A.

FT SK9010

2

EN

FR

WARNINGS

• Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the standards in force.

• All equipment must only be used for the purposes for which it was designed. The COMELIT GROUP s.p.a. disclaims all responsibility in the event of misuse of the
equipment, for modifications made by other people for whatever reason and for using non-original accessories and materials.

• All the products comply with the requirements of Directive 2006/95/CE (which replaced Directive 73/23/EEC and subsequent amendments). This is proven by the CE
mark on the products.

• Do not put the riser wires near the supply cables (230/400 v)

AVERTISSEMENTS

• Effectuer lʼinstallation en suivant scrupuleusement les instructions fournies par le constructeur et conformément aux normes en vigueur.

• Tous les appareils doivent être strictement destinés à lʼemploi pour lesquels ils ont été conçus. La société COMELIT GROUP s.p.a. décline toute responsabilité en cas
de mauvais usage des appareils, pour des modifications effectuées par dʼautres personnes pour nʼimporte quelle raison et pour lʼutilisation dʼaccessoires et matériaux
non dʼorigine.

• Tous les produits sont conformes aux prescriptions de la directive 2006/95/CE (qui remplace la directive 73/23/CEE et amendements successifs). Cela est attesté par
la présence du marquage CE sur les produits.

• Eviter de placer les fils de montants à proximité des câbles dʼalimentation (230/400 v)

NL

ES

WAARSCHUWING

• Volg de instructies van de fabrikant nauwkeurig en installeer de materialen volgens de plaatselijk geldende normen.

• Alle componenten mogen alleen gebruikt worden voor de doeleinden waarvoor ze zijn ontworpen. COMELIT GROUP s.p.a. is niet verantwoordelijk voor
oneigenlijk gebruik van de apparatuur, voor wijzigingen die om welke reden dan ook door derden zijn aangebracht, en voor het gebruik van accessoires en materialen
die niet door de fabrikant zijn aangeleverd.

• Alle producten voldoen aan de eisen van de richtlijn 2006/95/EG (die de richtlijn 73/23/EEG en latere wijzigingen vervangt). Dit wordt bevestigd door het CE-label op
de producten.

• Monteer de aders van de stamleiding niet in de nabijheid van voedingskabels (230/400V).

ADVERTENCIAS

• La instalación se ha de efectuar en conformidad con las normas vigentes, siguiendo atentamente las instrucciones suministradas por el fabricante.

• Todos los aparatos deben estar destinados exclusivamente al uso para el cual han sido construidos. COMELIT GROUP s.p.a. declina toda responsabilidad por el uso
impropio de los aparatos, por cambios efectuados por terceros por cualquier motivo o finalidad y por el uso de accesorios y materiales no originales.

• Todos los productos son conformes a los requisitos de las Directivas 2006/95/CE (que sustituye la Directiva 73/23/CEE y sucesivas enmiendas) como demuestra la
presencia de la marca CE en ellos.

• No poner los cables de la columna montante cerca de los cables de alimentación (230/400V).

FT SK9010

FT SK9010

3

ENGLISH

General introduction

The SK9010 radio frequency unit is a stand-alone control unit with an integral receiver
used to manage SK9060 radio transmitters in order to control access to an automatic
door. It uses the 868.3 Mhz frequency. The transmitters are registered automatically in
the memory by pressing their command button. They are managed later using the 3
buttons on the control unit. They can be put inside the premises to be controlled or in a
watertight casing.

Layout of the electronic card

The card is made up of:

- D1 ; D2 ; D3: Display

- S2: Used to return to programming mode

- S1 and S3: Used to scroll through the programmed locations and the timer
settings.

Description of terminals

1 : Power supply 12 - 24 Vdc
2 : 0 V power supply
3 : Manual command input
4 : NO relay output
5 : NC relay output
6 : Common relay output

N.B.: By connecting terminal 3 to the earth, the relay will be activated manually (e.g.

exit push button)

Programming a transmitter

- Press button S2 until the red dot on the display D3 lights up. Release the button.
“APR” appears on the display indicating that you are in programming mode. Press the
button for the transmitter to be programmed once. The display will show the number of
the memory on which it will record the remote control button. Pressing it once more
deletes the number and the “APR” message appears once more confirming that
programming has taken place. It is then possible to repeat the operation for another
transmitter.

To exit training mode press S2 once more.

Deleting a transmitter

- Press button S2 until the red dot on the display D2 lights up. Release the button.
“EFF” appears on the screen indicating that you are in delete mode. There are two
ways of deleting a transmitter:

1. Press the button on the transmitter to be deleted. This will be deleted from
the memory immediately and the display goes out.

2. Search for the location in the memory with buttons S1 and S3. When the
number is displayed, press S2. The relevant memory box will be deleted.

Deleting all

Press button S2 until the red dot on the display D1 lights up. Release the button. “EFF”
appears on the screen indicating that you are in delete all mode. Press S2 again. The
display flashes for ten seconds or so and then goes out. The memory has been
cleared.

Timer

The factory time setting is 2 seconds. To change it, you must press S2 until “REL” is
displayed. Release the button. The “tEP” message shows you that you are in timer
programming mode. By pressing S1 and S3 you can reduce or increase the time. After
setting the time (in seconds), wait for the display to go out. The receiver is in normal
operating mode with the new time setting.

Note: in programming mode, if there is no action for 20 seconds, the program exits
programming mode automatically to go back to use mode.

Technical characteristics

• Time for opening the door can be set from 1 - 255 seconds.

• Output via dry contact max. 5A at 250 VAC

• Frequency: 868.3 MHz (EN 300 220)

• Power consumption: 22 mA inactive relay, 95 mA active relay

• Range: 100 metres in a free field

• Operating temperature: -10°C - +55°C

• Operating voltage: 8 - 24 Vdc

• Dimensions (h x l x d) 55 x 87 x 20 mm

Connection example

RTE

It is necessary to use a separate Power Supply for the Electric Lock