Citroën C3 Dag 2010, C3 Dag Picasso 2010 Owner's Manual
FAMILIARISATION
Zenith windscreen
This large windscreen provides incomparable visibility and light in the passenger
compartment.
6
Stop & Start
This system puts the engine temporarily into standby during stops in the traf-
fi c (red lights, traffi c jams, etc...). The
engine restarts automatically as soon
as you want to move off. The Stop &
Start system reduces fuel consumption
and exhaust emissions, and provides
the comfort of complete silence when
stationary.
111
Temporary puncture repair kit
This kit is a complete system consisting
of a compressor and sealant cartridge,
to allow the temporary repair of a tyre.
127
Rear parking sensors
This system provides a warning when
reversing by detecting obstacles located
behind the vehicle.
118
FAMILIARISATION
Remote control key Fuel tank
1. Opening the fuel fi ller fl ap.
2. Opening and hooking the fuel fi ller
cap.
A. Unfolding/Folding the key.
B. Unlocking the vehicle.
60
69
A. Interior release lever.
B. Exterior safety catch.
C. Bonnet stay.
121
Bonnet
ACCESS
Other functions...
C. Normal locking of the vehicle
Vehicle location.
Tank capacity:
- approximately 50 litres (petrol),
- approximately 48 litres (Diesel).
FAMILIARISATION
ZENITH WINDSCREEN
System comprising a panoramic tinted
glass area to increase lighting and vision in the cabin.
Fitted with a manual blind to improve
thermal comfort and sun visors to avoid
dazzle.
Blind Sun visors
To open the blind, take it by its cen-
tral grip A , then pull it backwards
and guide it to the desired position.
To close the blind, take it by its cen-
tral grip A , then pull it forwards and
guide it to the desired position.
Before moving the blind, the sun visors
must be in the folded position.
Lower the sun visors to avoid dazzle.
Do not attach or hang heavy
objects to the blind or its guide
rails.
FAMILIARISATION
INTERIOR
Interior mood lighting
This subdued passenger compartment lighting improves visibility inside
the vehicle in low lighting conditions. It
comprises 4 lamps, located in the automatic day/night mirror support, in the
footwells and in the lower dashboard
storage compartment.
79
Gear shift indicator
Associated with the manual gearbox,
this system suggests when to change
up to obtain optimum fuel consumption.
104
Scented air freshener
The scented air freshener diffuses the
selected fragrance throughout the passenger compartment from its location in
the ventilation system.
54
Digital air conditioning
After setting the desired level of com-
fort, the system then automatically con-
trols this level according to the ambient
conditions.
51
Audio and communication systems
This equipment benefi ts from the lat-
est technology: MP3 compatible Audio
system, USB port, Bluetooth hands-free
system, MyWay with 16/9 colour screen,
auxiliary inputs, Hi-Fi audio system.
MyWay
169
Audio system
201
FAMILIARISATION
INSTRUMENTS AND CONTROLS
1. Cruise control/speed limiter
switches.
2. Headlamp height adjustment.
3. Steering wheel adjustment control.
4. Lighting and direction indicators
control stalk.
5. Instrument panel.
6. Driver's airbag.
Horn.
7. Gear lever.
8. 12 V accessory socket
USB port/auxiliary socket.
9. Heated seat control.
10. Bonnet release lever.
11. Door mirror controls.
Electric window controls.
Rear doors and electric windows
deactivation control.
12. Fusebox.
13. Stop & Start button.
Electronic stability programme
button (ESP/ASR).
14. Front door window demisting/
defrosting vent.
15. Speaker (tweeter).
16. Windscreen demisting/defrosting
vent.
FAMILIARISATION
INSTRUMENTS AND CONTROLS
1. Steering lock and ignition.
2. Audio equipment steering wheel
controls.
3. Wipers/screenwash/trip computer
control stalk.
4. Microphone.
5. Scented air freshener.
6. Central locking button.
7. Multifunction screen.
8. Hazard warning lamps switch.
9. Central adjustable air vents.
10. Sunshine sensor
Hi-Fi audio system central speaker.
11. Passenger's airbag.
12. Side adjustable air vent.
13. Glove box/Passenger's airbag
deactivation/Audio/video sockets.
14. Parking brake.
15. Central armrest with storage.
16. Upper and lower storage.
17. MyWay or Audio system.
18. Heating/air conditioning controls.
FAMILIARISATION
SITTING COMFORTABLY
Front seats
1. Forwards-backwards adjustment. 2. Height adjustment. 3. Seat back angle adjustment.
55
FAMILIARISATION
Other adjustments
4. Head restraint height adjustment.
56
Steering wheel adjustment
1. Release the adjustment mechanism.
2. Height and reach adjustment.
3. Lock the adjustment mechanism.
59
For reasons of safety, these op-
erations must only be carried out
with the vehicle stationary.
Other functions...
Heated seats.
SITTING COMFORTABLY
FAMILIARISATION
SITTING COMFORTABLY
Door mirrors
Adjustment
A. Selecting the mirror.
B. Adjusting the position of the mirror.
C. De-selecting the mirror.
58
Other functions...
Folding/Unfolding.
Rear view mirror
Manual day/night type
1. Selecting the "day" position of the
mirror.
2. Adjusting the mirror.
59
Automatic day/night type
Automatic detection of day/night mode.
1.
2. Adjusting the mirror.
59
Front seat belts
1. Fitting the belt.
2. Fastening.
3. Check that the belt is correctly fas-
tened by pulling on the belt webbing.
97
FAMILIARISATION
SEEING CLEARLY
Lighting
Ring A
Lighting off.
Automatic illumination of headlamps.
Sidelamps.
Dipped/main beam headlamps.
Ring B
Rear foglamps.
or
Front and rear foglamps.
Wipers
Control stalk A: windscreen wipers
2. Fast wipe.
1. Normal wipe.
Int. Intermittent wipe.
0. Park.
AUTO Automatic wiping or single
wipe.
Wash-wipe: pull the control stalk to-
wards you.
75
Switching on "AUTO" mode
Push the control stalk downwards
and release it.
Switching off "AUTO" mode
Push the control stalk upwards and
return it to position "0" .
77
Ring B: rear wiper
Park.
Intermittent wipe.
Wash-wipe.
71
76
FAMILIARISATION
VENTILATION
Advice on interior settings
Heating or Manual air conditioning
I require...
DEMISTING
DEFROSTING
Digital air conditioning: use of the fully automatic mode by pressing the "AUTO" button is recommended.
HEAT
COOL
Air distribution Air fl ow
Air recirculation /
Exterior air intake
Temperature Manual A/C
FAMILIARISATION
MONITORING
Instrument panel
A. With the ignition on, the fuel gauge
bars for the fuel remaining should
come on.
B. With the engine running, the associ-
ated low level warning lamp should
go off.
C. With the ignition on, the oil level in-
dicator should display "OIL OK" for
a few seconds.
If the levels are not correct, top up the
level which is low.
19
Warning lamps
1. With the ignition on, the orange and
red warning lamps come on.
2. With the engine running, these
warning lamps should go off.
If a warning lamp remains on, refer to
the page concerned.
21, 26
Switch panel
Illumination of the indicator lamp indicates the state of the corresponding
system.
A. ESP/ASR system deactivated.
96
B. Stop & Start system deactivated.
112
FAMILIARISATION
PASSENGER SAFETY
Front passenger's airbag
1. Open the glove box.
2. Insert the key.
3. Select position:
"ON" (activation), with front passen-
ger or "forwards facing" child seat,
"OFF" (deactivation), with "rear fac-
ing" child seat".
4. Remove the key keeping the switch
in the new position.
99
Front seat belts and
passenger's front airbag
A. Front seat belts not fastened or un-
fastened warning lamp.
97
B. Front passenger's airbag deactiva-
tion indicator lamp.
C. Front passenger's airbag activation
indicator lamp.
100
Electric child lock
Illumination of the lamp A indicates that
the rear door and rear electric window
controls are deactivated.
93
FAMILIARISATION
DRIVING SAFELY
Stop & Start
Going into engine STOP mode
Going into engine START mode
The "ECO" warning lamp comes
on in the instrument panel and
the engine goes into standby:
- with a manual gearbox; at speeds
below 12 mph (20 km/h), put the
gear lever into neutral, then release
the clutch pedal.
In some circumstances, STOP mode
may not be available; the "ECO" warn-
ing lamp fl ashes for a few seconds,
then goes off.
111
The "ECO" warning lamp goes
off and the engine restarts:
- with a manual gearbox; depress
the clutch pedal.
In certain circumstances, START mode
may be invoked automatically; the
"ECO" warning lamp fl ashes for a few
seconds, then goes off.
112
Deactivation/Reactivation
You can deactivate the system at
any time by pressing the "ECO OFF"
switch; the warning lamp in the button
comes on.
The system is reactivated automatically every time the vehicle
is started using the key.
Before refueling or doing any-
thing under the bonnet, you
must switch off the ignition with
the key.
113
FAMILIARISATION
DRIVING SAFELY
Speed limiter "LIMIT"
1. Selecting/Switching off speed limiter
mode.
2. Decrease the programmed value.
3. Increase the programmed value.
4. Speed limiter on/off.
The values must be set with the engine
running.
114
Cruise control "CRUISE"
1. Selecting/Switching off cruise con-
trol mode.
2. Decrease the programmed value.
3. Increase the programmed value.
4. Cruise control Off/Resume.
In order to be programmed or activated,
the vehicle speed must be higher than
25 mph (40 km/h), with at least fourth
gear engaged on a manual gearbox
(second gear on a SensoDrive or automatic gearbox).
116
Display in the instrument panel
The cruise control or speed limiter mode
appears in the instrument panel when it
is selected.
Cruise control
Speed limiter
Panel grouping together the vehicle operation indication dials and warning lamps.
Dials
1. Rev counter.
Indicates the speed of rotation of the
engine (x 1 000 rpm).
2. Vehicle speed.
Indicates the current speed of the
moving vehicle (mph or km/h).
3. Fuel level.
Indicates the quantity of fuel remain-
ing in the tank.
4. Screen.
5. Display management button
Servicing information.
Adjust the time and choose units.
Reset the service indicator.
6. Instrument panel lighting button.
Adjusts the brightness of the lighting
of the instruments and controls.
For more information, refer to the
section on the button or function
and its associated display.
MONITORING
Screen
A. Ambient temperature.
(°Celsius or °Fahrenheit)
B. Gear effi ciency indicator.
C. Time.
D. Engine oil level indicator.
Appears a few seconds after switching
on the ignition, then disappears.
E. Trip computer.
F. Service indicato r.
(miles or km) then,
Total mileage.
These two functions are displayed
successively when switching on the
ignition.
1
MONITORING
1
Panel grouping together the vehicle operation indication dials and warning lamps.
Depending on the version, the instrument panel may have permanent back-lighting.
Dials
1. Rev counter.
Indicates the speed of rotation of the
engine (x 1 000 rpm).
2. Vehicle speed.
Indicates the current speed of the
moving vehicle (mph or km/h).
3. Fuel level.
Indicates the quantity of fuel remaining
in the tank.
4. Screen.
5. Display management button
Alternates display between range
and trip mileage recorder.
Servicing information.
Resets the selected function to zero
(trip distance recorder or service in-
dicator).
6. Instrument panel lighting button.
Adjusts the brightness of the lighting
of the instruments and controls.
For more information, refer to the
section on the button or function
and its associated display.
Screen
A. Speed limiter
(mph or km/h) or
Cruise control.
B. Gear shift indicator.
C. SensoDrive or automatic gearbox
information.
D. Range
(miles or km) or
Trip mileage recorder.
E. Service indicator
(miles or km), then
Total mileage recorder
These two functions are displayed
successively when switching on the
ignition
F. Engine oil level indicator
Appears a few seconds after switching
on the ignition, then disappears.
MONITORING
Indicator and warning lamps
Visual indicators informing the driver that a system is in operation (operation or
deactivation indicator lamps) or of the occurrence of a fault (warning lamp).
When the ignition is switched on
Certain warning lamps come on for a few seconds when the vehicle's ignition is
switched on.
When the engine is started, these same warning lamps should switch off.
If they remain on, before moving off, refer to the information on the warning lamp concerned.
Operation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the corresponding
system has come into operation.
The warning lamps may come
on continuously (fi xed) or fl ash.
Certain warning lamps may
come on in two different modes.
Only by relating the type of lighting to the operating status of the
vehicle can it be ascertained
whether the situation is normal
or whether a fault has occurred.
Associated warnings
The switching on of certain warning lamps may be accompanied by an audible
signal and a message on the multifunction screen.
Warning lamp is on Cause Action/Observations
Left-hand
direction
indicato r
fl ashing with
buzzer.
The lighting stalk is pushed
down.
Right-hand
direction
indicator
fl ashing with
buzzer.
The lighting stalk is pushed up.
Sidelamps fi xed.
The lighting stalk is in the
"Sidelamps" position.
Hazard
warning lamps
fl ashing with
audible signal.
The hazard warning lamps
switch, located on the
dashboard, has been operated.
The left-hand and right-hand direction indicators
and their associated indicator lamps fl ash
simultaneously.
1
MONITORING
Warning lamp is on Cause Action/Observations
1
Parking brake fi xed.
Dipped beam
headlamps
Main beam
headlamps
Front
foglamps
Rear
foglamps
Diesel engine
pre-heating
fi xed.
fi xed.
fi xed.
fi xed.
fi xed.
The lighting stalk is in the
"Dipped beam headlamps"
position.
The lighting stalk is pulled
towards you.
The front foglamps are
switched on.
The rear foglamps are
switched on.
The ignition switch is at the
2nd position (ignition on).
The parking brake is
applied or not properly
released.
Pull the stalk to return to dipped beam
headlamps.
Turn the ring on the stalk rearwards twice to
switch off the front foglamps.
Turn the ring on the stalk rearwards to switch off
the rear foglamps.
Wait until the warning lamp goes off before
starting.
The period of illumination of the warning lamp is
determined by the climatic conditions (up to about
thirty seconds in extreme climatic conditions).
If the engine does not start, switch the ignition off
and then on, wait until the warning lamp goes off
again, then start the engine.
Release the parking brake to switch off the
warning lamp, keeping your foot on the brake
pedal.
Observe the safety recommendations.
For further information on the parking brake, refer
to the "Driving" section.
MONITORING
Stop & Start
fi xed.
The Stop & Start system
has put the engine in STOP
mode at a vehicle stop
(traffi c lights, traffi c jam, or
other...).
The warning lamp goes off and the engine
restarts automatically in START mode, as soon
as you want to move off.
fl ashes for a
few seconds,
then goes off.
STOP mode is temporarily
unavailable.
or
START mode is invoked
automatically.
Refer to "Driving - § Stop & Start" for special
cases with STOP mode and START mode.
Passenger's
airbag
system
fi xed.
The control switch, located
in the glove box, is in
the " ON " position.
The passenger's front
airbag is activated.
In this case, do not install a
rear-facing child seat.
Turn the control switch to the " OFF " position
to deactivate the front passenger's airbag.
In this case you can install a rear-facing child
seat.
Engine
coolant
temperature
fi xed blue .
On starting the engine, it
indicates that the engine is
cold.
After a few minutes driving, it swiches off to
indicate that the engine temperature is normal.
In order to protect your engine, avoid driving too
hard until the warning lamp has switched off.
Warning lamp is on Cause Action/Observations
1
MONITORING
Warning lamp is on Cause Action/Observations
1
With the SensoDrive gearbox, press the brake
pedal to start the engine (lever in position N ).
With an automatic gearbox, with the engine
fi xed.
Foot on the
brake pedal
Automatic
wiping
fl ashing.
fi xed.
The brake pedal must be
pressed.
With a SensoDrive gearbox,
if you hold the vehicle on an
incline using the accelerator
for too long, the clutch
overheats.
The wiper control is pushed
downwards.
running, press the brake pedal before releasing
the parking brake, to unlock the lever and come
out of position P .
If you wish to release the parking brake without
pressing the brake pedal, this warning lamp will
remain on.
Use the brake pedal and/or the parking brake.
Automatic front wiping is activated.
MONITORING
Deactivation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the corresponding system has been switched off intentionally.
This is may be accompanied by an audible signal and a message on the multifunction screen.
Passenger's
airbag
system
fi xed.
The control, located in the
glove box, is set to the OFF
position.
The passenger's front
airbag is deactivated.
In this case you can install
a "rear facing" child seat.
Set the control to the ON position to activate the
passenger's front airbag.
In this case, do not fi t a child seat in the rear-
facing position.
ESP/ASR fi xed.
The button, located at
the bottom left of the
dashboard, is pressed. Its
indicator lamp is on.
The ESP/ASR is
deactivated.
ESP: electronic stability
programme.
ASR: anti-skid regulation.
Press the button to activate the ESP/ASR. Its
indicator lamp goes off.
The ESP/ASR system is activated automatically
when the vehicle is started.
If deactivated, the system is reactivated
automatically from around 30 mph (50 km/h).
Warning lamp is on Cause Action/Observations
1
MONITORING
Warning lamps
When the engine is running or the vehicle is being driven, the switching on
of one of the following warning lamps
1
indicates a fault which requires action
on the part of the driver.
Warning lamp is on Cause Action/Observations
or associated
STOP
Service
warning lamp,
accompanied
by an audible
fi xed, alone
with another
signal and a
message on
the screen.
temporarily.
fi xed.
Any fault resulting in the illumination of a warning lamp must be investigated
further by reading the associated message in the multifunction screen.
If you encounter any problems, do not hesitate to contact a CITROËN
dealer or a qualifi ed workshop.
Illumination of the warning
lamp is associated with a
serious braking system or
engine coolant temperature
problem.
Minor problems have
occurred for which there is
no specifi c warning lamp.
Major problems have
occurred for which there is
no specifi c warning lamp.
Stop as soon as it is safe to do so as the engine
may cut out when driving.
Park, switch off the ignition and call a CITROËN
dealer or a qualifi ed workshop.
Identify the problem by reading the message
shown in the screen, such as, for example:
- the engine oil level,
- the screenwash level,
- the remote control battery,
- saturation of the particle emission fi lter on
Diesel vehicles (see "Checks - § particle
emissions fi lter").
For any other faults, contact a CITROËN dealer or
a qualifi ed workshop.
Identify the problem by reading the message
shown in the screen and contact a CITROËN
dealer or a qualifi ed workshop.
MONITORING
Anti-lock
Braking
System
(ABS)
fi xed.
The anti-lock braking
system has a fault.
The vehicle retains conventional braking.
Drive carefully at reduced speed and contact
a CITROËN dealer or a qualifi ed workshop
without delay.
Dynamic
stability
control
(ESP/ASR)
fl ashing.
The ESP/ASR regulation is
active.
The system optimises traction and improves the
directional stability of the vehicle.
fi xed.
Unless it has been
deactivated with the indicator
lamp in the button on, the
ESP/ASR system has a fault.
Have it checked by a CITROËN or a qualifi ed
workshop.
Engine
autodiagnosis
system
fi xed.
The emission control
system has a fault.
The warning lamp should go off when the engine is started.
If it does not go off, contact a CITROËN dealer or qualifi ed
workshop without delay.
fl ashing.
The engine management
system has a fault.
Risk of destruction of the catalytic converter.
Have it checked by a CITROËN dealer or a
qualifi ed workshop.
Braking
fi xed,
associated
with the STOP
warning lamp.
The braking system fl uid
level is too low.
You must stop as soon as it is safe to do so.
Top up with brake fl uid recommended by
CITROËN.
If the problem persists, have the system checked
by a CITROËN dealer or a qualifi ed workshop.
+
fi xed, associated
with the STOP
and ABS
warning lamp.
The electronic brake force
distribution (EBFD) system
has a fault.
You must stop as soon as it is safe to do so.
Have it checked by a CITROËN or a qualifi ed
workshop.
Warning lamp is on Cause Action/Observations
1
MONITORING
Warning lamp is on Cause Action/Observations
1
You must refuel as soon as possible to avoid
running out of fuel.
This warning lamp will come on every time the
Low fuel
level
Maximum
coolant
temperature
Engine oil
pressure
Battery
charge
fi xed.
fi xed red.
fi xed.
fi xed.
When it fi rst comes on there
remains approximately
5 litres of fuel in the tank.
The temperature of the
cooling system is too high.
There is a fault with the
engine lubrication system.
The battery charging circuit
has a fault (dirty or loose
terminals, slack or cut
alternator belt, ...).
ignition is switched on, until a suffi cient addition
of fuel is made.
Fuel tank capacity: approximately 50 litres
(petrol) or 48 litres (Diesel).
Never continue to drive until you run out of fuel
as this could damage the emission control and
injection systems.
Stop as soon as it is safe to do so.
Wait until the engine has cooled down before
topping up the level, if necessary.
If the problem persists, contact a CITROËN dealer
or qualifi ed workshop.
You must stop as soon it is safe to do so.
Park, switch off the ignition and contact a CITROËN
dealer or a qualifi ed workshop.
The warning lamp should go off when the engine
is started.
If it does not go off, contact a CITROËN dealer or
a qualifi ed workshop.
MONITORING
Airbags
temporarily.
This lamp comes on for
a few seconds when you
turn on the ignition, then
goes off.
This lamp should go off when the engine is
started.
If it does not go off, contact a CITROËN dealer or
a qualifi ed workshop.
fi xed.
One of the airbag or seat
belt pretensioner systems
has a fault.
Have it checked by a CITROËN dealer or a
qualifi ed workshop.
Seat belt not
fastened/
unfastened
fi xed then
fl ashing
accompanied
by
an increasing
audible signal.
The driver and/or the front
passenger has not fastened
or has unfastened their seat
belt.
Pull the strap then insert the tongue in the
buckle.
Door(s) open
fi xed if the
speed is
below 6 mph
(10 km/h).
A door or the boot is still
open.
Close the door or boot.
fi xed and
accompanied
by an audible
signal if the
speed is
above 6 mph
(10 km/h).
Warning lamp is on Cause Action/Observations
1
MONITORING
Warning lamp is on Cause Action/Observations
1
Power
steering
Water in
Diesel
Particle
emissions
fi lter (Diesel)
fi xed.
fi xed.
fi xed,
accompanied
by an audible
signal
message on
the risk of
blockage of
the particle
emissions fi lter.
fi xed,
accompanied
by an audible
signal
and and a
message that
the particle
emissions fi lter
additive level
is too low.
The power steering has a
fault.
The Diesel fuel fi lter
contains water.
This indicates that the
particle emissions fi lter
is starting to become
saturated.
This indicates the low level
of the additive reservoir.
Drive carefully at reduced speed.
Have it checked by a CITROËN dealer or a
qualifi ed workshop.
Risk of damage to the injection system on Diesel
engines.
Contact a CITROËN dealer or a qualifi ed
workshop without delay.
As soon as driving conditions allow, regenerate
the fi lter by driving at a speed of at least 35 mph
(60 km/h) until the warning lamp goes off.
Have the reservoir topped up as soon as
possible by a CITROËN dealer or a qualifi ed
workshop.
MONITORING
Service indicator
System which informs the driver when
the next service is due, in accordance
with the manufacturer's servicing
schedule.
The point at which the service is due is
calculated from the last indicator zero
reset. It is determined by two parameters:
- the distance travelled,
- the time elapsed since the last
service.
Between 600 miles (1 000 km) and
1 800 miles (3 000 km) remain before
the next service is due
For a few seconds after the ignition is
switched on, the spanner symbolising
the service operations comes on. The
distance recorder display line indicates
the distance remaining before the next
service is due.
Example: 1 700 miles (2 800 km) re-
main before the next service is due.
For a few seconds after the ignition is
switched on, the screen indicates:
Less than 600 miles (1 000 km)
remain before the next service is due
Example: 400 miles (900 km) remain
before the next service is due.
For a few seconds after the ignition is
switched on, the display indicates:
A few seconds after the ignition is
switched on, the spanner goes off ; the
distance recorder resumes its normal
operation. The screen then indicates
the total and trip distances.
A few seconds after the ignition is switched
on, the distance recorder resumes its normal operation. The spanner remains on
to indicate that a service must be carried
out soon.
More than 1 800 miles (3 000 km)
remain before the next service is due
When the ignition is switched on, no service information appears in the screen.
1
MONITORING
Service overdue
For a few seconds after the ignition is
switched on, the spanner fl ashes to
indicate that the service must be carried
1
out as soon as possible.
Example: the service is overdue by
180 miles (300 km).
For a few seconds after the ignition is
switched on, the display indicates:
A few seconds after the ignition is switched
on, the distance recorder resumes its normal operation. The spanner remains on .
The distance remaining may be
weighted by the time factor, depending on the driver's driving
habits.
Therefore, the spanner may also
come on if you have exceeded
the two year service interval.
Service indicator zero reset
After each service, the service indicator
must be reset to zero.
The procedure for resetting to zero is as
follows:
switch off the ignition,
press and hold the trip distance re-
corder zero reset button,
switch on the ignition; the distance re-
corder display begins a countdown,
when the display indicates "=0" ,
release the button; the spanner disappears.
Following this operation, if you
wish to disconnect the battery,
lock the vehicle and wait at least
fi ve minutes for the zero reset to
be taken into account.
Retrieving the service information
You can access the service information
at any time.
Press the trip distance recorder zero
reset button.
The service information is displayed
for a few seconds, then disappears.
MONITORING
Service overdue
For a few seconds after the ignition is
switched on, the spanner fl ashes to
indicate that the service must be carried
1
out as soon as possible.
Example: the service is overdue by
180 miles (300 km).
For a few seconds after the ignition is
switched on, the display indicates:
A few seconds after the ignition is switched
on, the distance recorder resumes its normal operation. The spanner remains on .
The distance remaining may be
weighted by the time factor, depending on the driver's driving
habits.
Therefore, the spanner may also
come on if you have exceeded
the two year service interval.
Service indicator zero reset
After each service, the service indicator
must be reset to zero.
The procedure for resetting to zero is as
follows:
switch off the ignition,
press and hold the trip distance re-
corder zero reset button,
switch on the ignition; the distance re-
corder display begins a countdown,
when the display indicates "=0" ,
release the button; the spanner disappears.
Following this operation, if you
wish to disconnect the battery,
lock the vehicle and wait at least
fi ve minutes for the zero reset to
be taken into account.
Retrieving the service information
You can access the service information
at any time.
Press the trip distance recorder zero
reset button.
The service information is displayed
for a few seconds, then disappears.
Loading...