Canon PIXMA IP100 series Easy Setup Instructions

Start Here

Easy Setup Instructions

Photo Printer

Important

When cleaning the exterior of the printer, use a soft cloth to wipe it gently. For details, refer to “Cleaning Your Printer” in the Quick Start Guide.

a Unpack the Printer.

Con rm the included items referring to the illustration printed on the lid of the packing box or “Included Items” in the Quick Start Guide.

A USB cable is necessary to connect the printer with your computer.

b Place the printer on a  at and

horizontal surface, and do not place any objects in front of the printer.

Remove all the shipping tapes on the outside of

the printer.

c Connect the power cord to the AC

adapter. Plug the AC adapter into the printer, and connect the other end of the power cord to the wall outlet.

Important

Do NOT connect the USB cable at this stage.

d Open the Rear Tray Cover and pull out

the Paper Support completely.

Paper Support

Rear Tray Cover

Paper Output Slot Cover

Note

The Paper Output Slot Cover will open automatically.

e Press the Power button to turn on the

printer.

1 Prepare the Printer 2 Install the Print Head 3 Install the Ink Tanks

a Open the Print Head Cover. The Print

Head Holder moves to the center.

Print Head Holder

Print Head Cover

b Unlock the Print Head Lock Lever by

squeezing both tabs inward.

Important Make sure the printer is turned on and the Power lamp is flashing green. Make sure the Print Head Holder has moved to the center.

c Raise the Print Head Lock Lever until it

stops.

Caution Do not touch internal parts other than the Print Head Lock Lever.

d Remove the Print Head from its

package.

Caution There may be some transparent or light blue ink on the inside of the bag the print head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items.

•

e Remove the orange protective cap from

the Print Head and discard it.

Protective Cap

Print Head Nozzles

Important Do not touch the print head nozzles. Do not reattach the protective tape once you have removed it.

f Insert the Print Head.

Align the mark on the Print Head with the mark on the Print Head Holder.

g Lower the Print Head Lock Lever

carefully.

h Push both tabs in left to right order until

each clicks into place.

Important

Make sure that the Print Head Lock Lever is ﬁ rmly

locked into the Print Head Holder by pressing both tabs on the Print Head Lock Lever until it clicks.

•

Note

For the ink tanks compatible with this printer, refer to the back cover of the Quick Start Guide.

a Remove the orange protective cap and

discard it.

Protective Cap

Ink Port

Electrical Contacts

Important Do not touch the electrical contacts and the ink port. Do not reattach the protective tape once you have removed it.

b Insert the Black ink tank at a slant into

the right slot.

Align the mark on the ink tank with the mark on the Print Head Holder.

c Press the mark on the ink tank until it

clicks into place.

Important Make sure that the ink lamp lights red. If the ink lamp does not light red after it is inserted, repeat steps b and c. If the Print Head Cover is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Print Head Cover to

return the holder to the center.

•

d Similarly, insert the Color ink tank into

the left slot.

Important If the front (innermost) part of the ink tank (A) is sticking up, push down on the Canon logo on the ink tank as illustrated below. Do not remove the ink tank forcibly.

(A)

e Close the Print Head Cover.

Important Once you have installed both ink tanks, the Power

lamp will ﬂ ash green. Wait for about 2 minutes, until the Power lamp stops ﬂ ashing and changes to steady, non-ﬂ ashing green and the printer has

stopped making operating noises, before proceeding.

Note

If the Alarm lamp on the printer  ashes orange after you have closed the Print Head Cover, refer to “Alarm Lamp Flashes Orange” in “Troubleshooting” of the

Quick Start Guide.

4 Load Printing Paper

a Load a sheet of supplied paper (Paper

For Print Head Alignment MP-101) loaded with the printing side (whiter side) facing UP in the Rear Tray, align the paper stack against the guide on the right side of the Rear Tray.

Make sure that the Paper Thickness Lever is set to the right.

Print Side

Paper Guide

Paper Thickness Lever

MP-101

Hardware setup is now complete.

Next, turn over and install the software.

5 Software Installation

Note

The screens below refer to Windows Vista™ operating system Ultimate Edition (hereafter referred to as “Windows Vista”) installation. Screens may vary depending on the operating system you are using. Log into a user account with the administrator privilege. Do not switch users during the installation process. Quit all running applications before installation. A message asking for your confirmation to restart your computer may appear during the installation process. If this message is displayed, follow the on-screen instructions and click OK. The installation resumes from where it left off when your computer has been restarted. If the computer is restarted during installation, do not remove the Setup CD-ROM during restarting.

a Be sure to TURN THE PRINTER OFF before continuing.

(1) Press the Power button. (2) Make sure that the Power lamp stops ashing.

b Turn the computer on and start Windows

Important

If the Found New Hardware or Found New Hardware Wizard screen appears automatically, remove the USB cable connected to your computer. Click Cancel to quit the screen. The screen may close automatically when the USB cable is unplugged.

Then turn off the printer and proceed from step c to install the software. When performing infrared communication, click Cancel to quit the screen. Then turn off the printer and proceed from step c to install the software.

c Insert the Setup CD-ROM. The setup program should run

automatically.

In Windows Vista, go to Step d. In Windows XP and Windows 2000, go to

Step f.

Note

If installation does not start automatically, refer to “Troubleshooting” instructions in the

Quick Start Guide.

d If the AutoPlay screen appears, click Run Msetup4.exe.

e If the User Account Control screen appears, click Continue.

If the same screen reappears in subsequent steps, click

Continue.

f When the main menu appears, click Easy Install.

The printer driver, On-screen Manuals, and application software are installed automatically.

Note

If you want to select particular items to install, click Custom Install and follow the onscreen instructions to proceed the installation. To install Adobe® RGB (1998), click Custom Install and follow the instruction on the screen.

g When the list of software to install appears, conrm the contents,

click Install.

Note

Move the cursor over items to display explanations of each application.

h Read the License Agreement carefully and click Yes. The

software installation screen may appear during the installation process. Follow the on-screen instructions to install the software.

i When the Printer Connection screen appears, connect one

end of the USB cable to the computer, the other to the printer, then TURN THE PRINTER ON. The printer driver will begin identifying the printer port being used.

When performing infrared communication, make the IrDA port of each other’s device stand opposite to each other. Distance between the IrDA ports should be 8 inch (20 cm) or less.

Important

If you cannot go to the next procedure after 2 minutes, refer to “Troubleshooting”

instructions in the Quick Start Guide.

•

USB

→

To Computer

j When the Print Head Alignment screen appears, make sure

that a sheet of supplied paper (Paper For Print Head Alignment MP-101) is loaded in the Rear Tray. Click Execute, conrm the displayed message and click Align Print Head.

Note

Print Head Alignment will take about 5 minutes to complete. Do not start another operation until the printer has stopped making operating noises. Do not open the Print Head Cover while printing.

The pattern is printed, and the Print Head is aligned automatically.

Note

The pattern is printed in black and blue. When Automatic Print Head Alignment cannot be executed properly, the Alarm lamp on the printer will flash orange eleven times. Refer to “Alarm Lamp Flashes Orange” in “Troubleshooting” of the Quick Start Guide.

k After print head alignment is completed, click Next. l When the Installation Results screen appears, click Next.

m When the User Registration screen appears, click Next.

Note

To register later, click Cancel and go to Step n. After software installation is complete, double-click on the desktop .

Follow on-screen instructions to register your product. You will need your product serial number, which is located on the rear of the printer.

Serial Number

n When the PIXMA Extended Survey Program screen appears,

conrm the message. We would appreciate it if you would take part in this program regarding the use of Canon printers. If you can agree, click Agree.

If Do not agree is clicked, the PIXMA Extended Survey Program will not be installed but you can use the printer normally.

o When the Installation completed successfully screen

appears, click Exit. Remove the Setup CD-ROM after clicking Exit.

If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart.

Remove the Setup CD-ROM after restarting the computer.

Note

Keep the Setup CD-ROM in a safe place in case you need to reinstall the software.

Software installation and print head alignment are now complete.

•

Note

Since Mac® OS 9, Mac OS X Classic environments, or Mac OS X v.10.3.8 or earlier are not supported, do not connect the printer to these. Use Mac OS X v.10.3.9 or later. The screens below refer to Mac OS X v.10.4.x installation. Screens may vary depending on the operating system you are using. Log on as an Administrator. Quit all running applications before installation.

a Connect one end of the USB cable to the computer, the other to

the printer.

Note

Make sure the printer is turned on.

USB

b Turn on your Mac and insert the Setup CD-ROM.

Note

If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop.

c Double-click the Setup icon.

d When the Authenticate screen appears, enter your

administrator name and password. Click OK. If you do not know your administrator name or password, click

, then follow the on-screen instructions.

e When the main menu appears, click Easy Install.

The printer driver, On-screen Manuals, and application software are installed automatically.

Note

If you want to select particular items to install, click Custom Install and follow the onscreen instructions to proceed the installation.

f When the list of software to install appears, conrm the contents,

then click Install.

Note

Move the cursor over items to display explanations of each application.

g Read the License Agreement carefully and click Yes. The

software installation screen may appear during the installation process. Follow the on-screen instructions to install the software.

h When the Start Setup screen appears, click Execute.

i When the Printer Connection screen appears, conrm the

displayed message and click Restart.

The system is restarted automatically.

Note

Do not remove the Setup CD-ROM while your computer is being restarted.

•

j When the Print Head Alignment screen appears, make sure

that a sheet of supplied paper (Paper For Print Head Alignment MP-101) is loaded in the Rear Tray. Click Execute, conrm the displayed message, and click OK.

Note

Print Head Alignment will take about 5 minutes to complete. Do not start another operation until the printer has stopped making operating noises. Do not open the Print Head Cover while printing.

The pattern is printed, and the Print Head is aligned automatically.

Note

k When the Setup Complete screen appears, click Next.

l When the User Registration screen appears, click Next.

Note

To register later, click Cancel and go to Step m. After software installation is complete,

double-click on the desktop.

Follow on-screen instructions to register your product. You will need your product serial number, which is located on the rear of the printer.

Serial Number

m When the Installation completed successfully screen

appears, click Exit. Remove the Setup CD-ROM after clicking Exit.

If Restart is displayed, click Restart. Remove the Setup CD-ROM after restarting the computer.

Note

Keep the Setup CD-ROM in a safe place in case you need to reinstall the software.

Software installation and print head alignment are now complete.

•

“Microsoft” is a registered trademark of Microsoft Corporation. “Windows” is a trademark of Microsoft Corporation, registered in the U.S. and other countries. “Windows Vista” is a trademark of Microsoft Corporation. “Macintosh” and “Mac” are trademarks of Apple Inc., registered in the U.S. and other countries. “Adobe” and “Adobe RGB (1998)” are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.