Canon MF4770N, Lbp7780cdn User Manual

Read this guide first.

ACT LNK

Please read this guide before operating this product. After you finish reading this guide, store it in a safe place for future reference.

Quick Setup Guide

Read the "Important Safety Instructions" section on the back side of this Setup Guide carefully to install the printer safely.

Check!

Did you remove all the packing materials?

Make sure that all the orange tape is completely removed.

Connect the printer and computer.

USB

Confirm the supplied accessories.

Remove the packing materials.

Remove all the tape.

Remove all the orange tape attached to the printer when performing the following procedure.

The packing materials may be changed in form or placement, or may be added or removed without notice.

User Manual CD-ROM

User Software CD-ROM

Close the covers after you finish checking.

Move the printer.

Left Side View

Rear Side View

OFF

A message prompts you to turn on the printer during the printer driver installation.

LAN

Load paper.

Hooks

Hook

Connect the power cord.

Up to here

Configure the network settings, if necessary.

See the e-Manual.

R T 5 - 1 0 1 5 - 0 1 0

RT5-1015 (010) XXXXXXXXXX © CANON INC. 2013 PRINTED IN CHINA

Install the driver.

Check the printing operation.

Important Safety Instructions

This manual describes only warnings and cautions for the installation and the power supply. Be sure to read "Important Safety Instructions" described in the e-Manual (HTML manual) included in the supplied User Manual CD-ROM also.

User Manual CD-ROM

Follow the instructions on the screen.

If you have any questions about operations, see the "Printer Driver Installation Guide."

See the e-Manual.

Setup is finished.

For more about using the printer, see the e-Manual.

Installation

- Do not install the printer in a location near alcohol, paint thinner, or other flammable substances. If flammable substances come into contact with electrical parts inside the printer, this may result in a fire or electrical shock.

- Do not place the following items on the printer.

- Necklaces and other metal objects

- Cups, vases, flowerpots, and other containers filled with water or

liquids If these items come into contact with a high-voltage area inside the printer, this may result in a fire or electrical shock. If these items are dropped or spilled inside the printer, immediately turn OFF the power switch (1) and disconnect the interface cables if they are connected (2). Then, unplug the power plug from the AC power outlet (3) and contact your local authorized Canon dealer.

(1)

(2)

(1)

- When installing or removing the optional accessories, be sure to turn the printer OFF, unplug the power plug, and then disconnect all the interface cables and power cord from the printer. Otherwise, the power cord or interface cables may be damaged, resulting in a fire or electrical shock.

- Do not install the printer in unstable locations, such as on unsteady platforms or inclined floors, or in locations subject to excessive vibrations, as this may cause the printer to fall or tip over, resulting in personal injury.

- The ventilation slots are provided for proper ventilation of working parts inside the printer. Never place the printer on a soft surface, such as a bed, sofa, or rug. Blocking the slots can cause the printer to overheat, resulting in a fire.

- Do not install the printer in the following locations, as this may result in a fire or electrical shock.

- A damp or dusty location

- A location exposed to smoke and steam, such as near a cookery or

humidifier

- A location exposed to rain or snow

- A location near a water faucet or water

- A location exposed to direct sunlight

- A location subject to high temperatures

- A location near open flames

- When installing the printer, gently lower the printer to the installation site so as not to catch your hands between the printer and the floor or between the printer and other equipment, as this may result in personal injury.

- When connecting the interface cable, connect it properly by following the instructions in the e-Manual. If not connected properly, this may result in malfunction or electrical shock.

- Be careful when handling the main board or the ROM. Touching the main board or the sharp parts such as the edges of the ROM may result in personal injury.

- When moving the printer, follow the instructions in the e-Manual to hold it correctly. Failure to do so may cause you to drop the printer, resulting in personal injury.

(2)

(3)

Symbols

Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly. To use the machine safely, always pay attention to these warnings.

Indicates a caution concerning operations that may lead to injury to persons if not performed correctly. To use the machine safely, always pay attention to these cautions.

Power Supply

- Do not damage or modify the power cord. Also, do not place heavy objects on the power cord or pull on or excessively bend it, as this can cause electrical damage, resulting in fire or electrical shock.

- Keep the power cord away from all heat sources. Failure to do so can cause the power cord insulation to melt, resulting in a fire or electrical shock.

- The power cord should not be taut, as this may lead to a loose connection and cause overheating, which could result in a fire.

- The power cord may become damaged if it is stepped on, fixed with staples, or if heavy objects are placed on it. Continued use of a damaged power cord can lead to an accident, such as a fire or electrical shock.

- Do not plug or unplug the power plug with wet hands, as this can result in electrical shock.

- Do not plug the power cord into a multi-plug power strip, as this can result in a fire or electrical shock.

- Do not bundle up or tie up the power cord in a knot, as this can result in a fire or electrical shock.

- Insert the power plug completely in the AC power outlet. Failure to do so can result in a fire or electrical shock.

- If excessive stress is applied to the connection part of the power cord, it may damage the power cord or the wires inside the machine may disconnect. This could result in a fire. Avoid the following situations:

- Connecting and disconnecting the power cord frequently.

- Tripping over the power cord.

- The power cord is bent near the connection part, and continuous stress

is being applied to the power outlet or the connection part.

- Applying a shock to the power connector.

- Do not use power cords other than the one provided, as this can result in a fire or electrical shock.

- As a general rule, do not use extension cords. Using an extension cord may result in a fire or electrical shock.

- Do not use a power supply voltage other than that listed herein, as this may result in a fire or electrical shock.

- Always grasp the power plug when unplugging the power plug. Do not pull on the power cord, as this may expose the core wire of the power cord or damage the cord insulation, causing electricity to leak, resulting in a fire or electrical shock.

- Leave sufficient space around the power plug so that it can be unplugged easily. If objects are placed around the power plug, you may be unable to unplug it in an emergency.

Others

To avoid the risk of personal injury or damage to the printer, and for legal information, make sure to read the "Legal Notices" and "Important Safety Instructions" in the e-Manual included on the accompanying User Manual CD-ROM carefully before using the printer.