Quick Setup Guide
Start Here
Before you can use the machine, please read this Quick Setup Guide for the correct setup and installation.
To view the Quick Setup Guide in other languages, please visit http://solutions.brother.com/
DCP-9010CN
.
IMPORTANT
DO NOT connect the interface cable yet.
Unpack the machine and check the components
1
Waste Toner Box
(pre-installed)
Quick Setup Guide
Belt Unit
(pre-installed)
CD-ROM
(Windows
(Macintosh)
Drum Unit and Starter Toner Cartridge
(Black, Cyan, Magenta and Yellow)
®
)
Assemblies
AC Power Cord
WARNING
• Plastic bags are used in the packaging of your machine. To avoid danger of suffocation, please keep
these bags away from babies and children.
• This machine is heavy and weighs approximately 22.7 kg. (50.0 lb). To prevent injuries use at least two
people to lift the machine. Be careful not to pinch your fingers when you put the machine back down.
UK/IRE Version 0
1
Note
Keep a minimum gap around the machine as shown in the illustration.
400 mm
100 mm
100 mm
120 mm
Note
• The components included in the box may differ depending on your country.
• Save all packing materials and the box in case for any reason you must ship your machine.
• The interface cable is not a standard accessory. Buy the appropriate interface cable for the interface you
want to use (USB or Network).
USB cable
• Please make sure you use a USB 2.0 cable (Type A/B) that is no longer than 2 metres.
• DO NOT connect the interface cable at this time. Connecting the interface cable is done during MFL-Pro
installation process.
• When you use a USB cable, make sure you connect it to the USB port of your computer and not to a USB
port on a keyboard or non-powered USB hub.
Network cable
Use a straight-through Category 5 (or greater) twisted-pair cable for 10BASE-T or 100BASE-TX Fast Ethernet
Network.
2
Symbols used in this guide
WARNING
CAUTION
IMPORTANT
Note
User's Guide
Network User's
Guide
WARNINGs tell you what to do to prevent possible personal injury.
CAUTIONs specify procedures you must follow or avoid to prevent possible minor injuries.
IMPORTANT specifies procedures you must follow or avoid to prevent possible damage to the
machine or other objects.
Notes tell you how you should respond to a situation that may arise or give tips about how the
current operation works with other features.
Indicates reference to the User's Guide or Network User's Guide which is on the CD-ROM we
have supplied.
3
Remove the packing
material from the
2
IMPORTANT
• Save all packing material and the carton in
case you have to ship your machine.
• DO NOT plug in the AC power cord yet.
machine
a Remove the packing tape from the outside of
the machine.
b Open the top cover by lifting up on the
handle a.
c Remove the packing material from the inside of
the machine.
1
4
Install the drum unit and
Y
toner cartridge
3
assemblies
a Unpack the four drum unit and toner cartridge
assemblies and gently shake each of them
from side to side several times to distribute the
toner evenly inside the assembly.
c Slide all four of the drum unit and toner
cartridge assemblies into the machine as
shown in the illustration. Make sure that you
match the toner cartridge colour to the same
colour label on the machine.
b Remove the protective cover by pulling on the
tab as shown in the illustration.
Note
Do not touch the surface of the packing film. It
may contain toner powder which can stain your
skin and clothing.
C
M
K
C - Cyan Y - Yellow
M - Magenta K - Black
d Close the top cover of the machine.
IMPORTANT
To avoid print quality
problems, DO NOT touch the
surface of the drum unit.
5
Load paper in the paper
4
tray
a Pull the paper tray completely out of the
machine.
d Put paper in the tray, and make sure that the
paper is below the maximum paper mark a.
The side to be printed on must be face down.
IMPORTANT
Make sure the paper guides touch the sides of
the paper so it will feed correctly.
b While pressing the green paper-guide release
lever a, slide the paper guides to fit the paper
size you are loading in the tray. Make sure that
the guides are firmly in the slots.
c Fan the stack of paper well to avoid paper jams
and misfeeds.
e Put the paper tray firmly back in the machine.
Make sure that it is completely inserted into the
machine.
f Unfold the support flap a to prevent paper
from sliding off the face-down output tray.
1
6
Connect the power cord
Choose your language
5
IMPORTANT
DO NOT connect the interface cable yet.
a Make sure that the machine’s power switch is
off. Connect the AC power cord to the machine.
b Plug the AC power cord into an AC outlet. Turn
the power switch on.
6
a After turning the power switch on, the LCD
shows:
Select Language
Press OK Key
Press OK.
b Press a or b to choose your language and
press OK.
Select ab or OK
English
c The LCD prompts you to confirm your
selection.
English?
1.Yes 2.No
If the LCD shows the correct language, press
1.
—OR—
Press 2 to go back to step b to choose the
language again.
Note
If you have set the wrong language, you can
change the language from the control panel menu
of the machine. (Menu, 1, 0)
7
Set the LCD contrast
7
If you are having difficulty reading the LCD, try
changing the contrast setting.
(if needed)
a Press Menu, 1, 4.
General Setup
4.LCD Contrast
b Press a to increase the contrast.
—OR—
Press b to decrease the contrast.
Press OK.
c Press Stop/Exit.
8
Choose your connection type
8
For USB Interface Users
Windows®, go to page 10
Macintosh, go to page 14
For Wired Network
Windows®, go to page 16
Macintosh, go to page 21
Windows
®
USB
Macintosh
Windows
Wired Network
®
Macintosh
Note
For Windows Server® 2003/ 2008, see the Network User’s Guide on the CD-ROM.
9
USB
For USB Interface Users
®
(Windows
Windows Vista
2000 Professional/XP/XP Professional x64 Edition/
®
)
Windows
®
Before you install
9
a Make sure that your computer is ON and you
are logged on with Administrator rights.
IMPORTANT
• DO NOT connect the USB cable yet.
• If there are any programs running, close
them.
• The screen may differ depending on the
operating system.
• The supplied CD-ROM includes ScanSoft™
PaperPort™ 11SE. This software supports
Windows
greater), XP Professional x64 Edition and
Windows Vista
Windows
MFL-Pro Suite.
b Turn off and unplug the machine from the AC
outlet and disconnect it from your computer, if
you already connected an interface cable.
®
2000 (SP4 or greater), XP (SP2 or
®
. Update to the latest
®
Service Pack before installing
Install MFL-Pro Suite
10
a Put the supplied CD-ROM into your CD-ROM
drive. If the model name screen appears,
choose your machine. If the language screen
appears, choose your language.
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click Start.exe.
b The CD-ROM main menu will appear. Click
Initial Installation.
10
c Click Install MFL-Pro Suite.
USB
Windows
®
Note
• If the installation does not continue
automatically, open the main menu again by
ejecting and then reinserting the CD-ROM or
double-click the Start.exe program from the
root folder, and continue from step c to install
MFL-Pro Suite.
• For Windows Vista
User Account Control screen appears, click
Allow.
®
, when the
d When the ScanSoft™ PaperPort™ 11SE
License Agreement window appears, click
Yes if you agree to the Software
License Agreement.
g Choose Local Connection, and then click
Next. The installation continues.
Note
If you want to install the PS driver (Brother’s
BR-Script Driver), choose Custom Install and
then follow the on-screen instructions. When the
Select Features screen appears, check
PS Printer Driver, and then continue following
the on-screen instructions.
h If you do not want to monitor the machine
status and error notification from your
computer, uncheck Enable Status Monitor
and then click Next.
Windows
®
USB
Macintosh
e The installation of ScanSoft™ PaperPort™
11SE will automatically start and is followed by
the installation of MFL-Pro Suite.
f When the Brother MFL-Pro Suite Software
License Agreement window appears, click
Yes if you agree to the Software
License Agreement.
i When this screen appears, go to the next step.
11
USB
Windows
®
Connect the USB cable
11
IMPORTANT
• DO NOT connect the machine to a USB port
on a keyboard or a non-powered USB hub.
• Connect the machine directly to your
computer.
a Remove the label covering the USB interface
connector.
Connect the power cord
12
a Plug the AC power cord into an AC outlet. Turn
the power switch on.
The installation will continue automatically.
The installation screens appear one after
another.
IMPORTANT
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
b When the On-Line Registration screen is
displayed, make your selection and follow the
on-screen instructions. Once you have
completed the registration process, close your
web browser to return to this window.
Then click Next.
b Connect the USB cable to the USB connector
on the machine marked with the symbol.
Then connect the cable to your computer.
12
USB
Finish and restart
Windows
®
13
a Click Finish to restart your computer.
After restarting the computer, you must be
logged on with Administrator rights.
Note
If an error message appears during the software
installation, run the Installation Diagnostics
located in Start/All Programs/Brother/
DCP-XXXX (where DCP-XXXX is your model
name).
b If this screen appears, choose the firmware
update setting and click OK.
Windows
®
USB
Macintosh
Note
Internet access is required for the firmware
upgrade.
The installation is now
Finish
Note
XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is the
most suitable driver when printing from the
applications that use the XML Paper Specification
documents. Please download the latest driver by
accessing the Brother Solutions Center at
http://solutions.brother.com/
complete.
.
13
USB
For USB Interface Users (Mac OS X 10.3.9 or greater)
Before you install
9
a Make sure your machine is connected to the
power and your Macintosh is ON. You must be
logged on with Administrator rights.
IMPORTANT
For the latest drivers and information on the
Mac OS X you are using, visit
http://solutions.brother.com/
.
Macintosh
b Connect the USB cable to the USB connector
on the machine marked with the symbol.
Then connect the cable to your computer.
Connect the USB cable
10
IMPORTANT
• DO NOT connect the machine to a USB port
on a keyboard or a non-powered USB hub.
• Connect the machine directly to your
Macintosh.
a Remove the label covering the USB interface
connector.
Install MFL-Pro Suite
11
a Put the supplied CD-ROM into your CD-ROM
drive.
b Double-click Start Here OSX to install.
14
Note
Please see the Software User’s Guide on the
CD-ROM if you want to install the PS driver.
(Brother’s BR-Script Driver)
c Please wait, it will take a few seconds for the
software to install. After the installation, click
Restart to finish installing the software.
USB
d The Brother software will search for the Brother
device.
e Choose the machine from the list, and then
click OK.
Macintosh
Install
12
When Presto! PageManager is installed OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
documents using Presto! PageManager.
Presto! PageManager
Windows
®
USB
f When this screen appears, click OK.
The installation of MFL-Pro Suite is now
complete.
Go to step 12 on page 15.
a Double-click Presto! PageManager and follow
the on-screen instructions.
The installation is now
Finish
complete.
Macintosh
15
Wired Network
For Wired Network Interface Users
®
(Windows
Windows Vista
2000 Professional/XP/XP Professional x64 Edition/
®
)
Windows
®
Before you install
9
a Make sure that your computer is ON and you
are logged on with Administrator rights.
IMPORTANT
• If there are any programs running, close
them.
• The screens may differ depending on the
operating system.
• The supplied CD-ROM includes ScanSoft™
PaperPort™ 11SE. This software supports
Windows
greater), XP Professional x64 Edition and
Windows Vista
Windows
MFL-Pro Suite.
IMPORTANT
Disable all personal firewall
software (other than Windows
®
2000 (SP4 or greater), XP (SP2 or
®
. Update to the latest
®
Service Pack before installing
®
Connect the network
10
cable
a Connect the network interface cable to the LAN
connector marked with a symbol and then
connect it to a free port on your hub.
Connect the power cord
11
a Plug the AC power cord into an AC outlet. Turn
the power switch on.
Firewall), anti-spyware or
antivirus applications for the
duration of the installation.
b Unplug the machine from the AC outlet.
16
Wired Network
Windows
®
Install MFL-Pro Suite
12
a Put the supplied CD-ROM into your CD-ROM
drive. If the model name screen appears,
choose your machine. If the language screen
appears, choose your language.
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click Start.exe.
b The CD-ROM main menu will appear. Click
Initial Installation.
Note
• If the installation does not continue
automatically, open the main menu again by
ejecting and then reinserting the CD-ROM or
double-click the Start.exe program from the
root folder, and continue from step c to install
MFL-Pro Suite.
• For Windows Vista
User Account Control screen appears, click
Allow.
®
, when the
d When the ScanSoft™ PaperPort™ 11SE
License Agreement window appears, click
Yes if you agree to the Software
License Agreement.
Windows
Wired Network
®
Macintosh
c Click Install MFL-Pro Suite.
e The installation of ScanSoft™ PaperPort™
11SE will automatically start and is followed by
the installation of MFL-Pro Suite.
f When the Brother MFL-Pro Suite Software
License Agreement window appears, click
Yes if you agree to the Software
License Agreement.
17
Wired Network
Windows
®
g Choose Wired Network Connection, and
then click Next.
Note
If you want to install the PS driver (Brother’s
BR-Script Driver), choose Custom Install and
then follow the on-screen instructions. When the
Select Features screen appears, check
PS Printer Driver, and then continue following
the on-screen instructions.
h For Windows
Professional x64 Edition/ Windows Vista
users, when this screen appears, choose
Change the Firewall port settings to enable
network connection and continue with the
installation. (Recommended) and click Next.
®
XP SP2 or greater/XP
®
Note
• You can find your machine’s IP address and
the node name by printing out the Network
Configuration List. See Print the Network
Configuration List on page 25.
• If your machine is not found over the network,
the following screen will appear.
Confirm your network settings by following the
on-screen instructions.
• If the IP Address of the machine is not yet
configured for use on your network, the
following screen appears.
If you are not using the Windows
the User’s Guide for your software for
information on how to add the following
network ports.
For network scanning, add UDP port 54925.
If you still have trouble with your network
connection, add UDP port 137.
®
Firewall, see
i If the machine is configured for your network,
choose the machine from the list, and then click
Next.
Click OK and then Configure IP Address.
Enter an IP address for your machine that is
suitable for your network by following the onscreen instructions.
j If you do not want to monitor the machine
status and error notification from your
computer, uncheck Enable Status Monitor
and then click Next.
18
Wired Network
k The installation of the Brother drivers will
automatically start. The installation screens
appear one after another.
IMPORTANT
DO NOT cancel any of the screens during the
installation. It may take a few seconds for all
screens to appear.
Note
For Windows Vista®, when this screen appears,
select the check box and click Install to complete
the installation correctly.
Windows
®
Finish and restart
13
a Click Finish to restart your computer. After
restarting the computer, you must be logged on
with Administrator rights.
l When the On-Line Registration screen is
displayed, make your selection and follow the
on-screen instructions. Once you have
completed the registration process, close your
web browser to return to this window.
Then click Next.
Note
If an error message appears during the software
installation, run the Installation Diagnostics
located in Start/All Programs/Brother/
DCP-XXXX LAN (where DCP-XXXX is your
model name).
b If this screen appears, choose the firmware
update setting and click OK.
Note
Internet access is required for the firmware
upgrade.
Windows
Wired Network
®
Macintosh
19
Wired Network
Install MFL-Pro Suite on
additional computers
14
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
each computer. Go to step 12 on page 17.
Note
Network license (Windows®)
This product includes a PC license for up to 5
Users. This license supports the installation of the
MFL-Pro Suite including ScanSoft™ PaperPort™
11SE on up to 5 PCs on the network. If you want
to use more than 5 PCs with ScanSoft™
PaperPort™ 11SE installed, please purchase the
Brother NL-5 pack which is a multiple PC license
agreement pack for up to 5 additional users. To
purchase the NL-5 pack, contact your authorized
Brother dealer or contact Brother customer
service.
(if needed)
Windows
®
The installation is now
Finish
Note
XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is the
most suitable driver when printing from the
applications that use the XML Paper Specification
documents. Please download the latest driver by
accessing the Brother Solutions Center at
http://solutions.brother.com/
complete.
.
20
Wired Network
For Wired Network Interface Users (Mac OS X 10.3.9 or greater)
Macintosh
Before you install
9
a Make sure your machine is connected to the
power and your Macintosh is ON. You must be
logged on with Administrator rights.
IMPORTANT
For the latest drivers and information on the
Mac OS X you are using, visit
http://solutions.brother.com/
Connect the network
10
cable
a Connect the network interface cable to the LAN
connector marked with a symbol and then
connect it to a free port on your hub.
.
Install MFL-Pro Suite
11
a Put the supplied CD-ROM into your CD-ROM
drive.
b Double-click Start Here OSX to install.
Windows
Wired Network
®
Macintosh
Note
Please see the Network User’s Guide on the
CD-ROM if you want to install the PS driver.
(Brother’s BR-Script Driver)
c Please wait, it will take a few seconds for the
software to install. After the installation, click
Restart to finish installing the software.
d The Brother software will search for the Brother
device.
21
Wired Network
e If the machine is configured for your network,
choose the machine from the list, and then click
OK.
Note
If your machine is not found over the network,
confirm your network settings.
Note
If this screen appears click OK.
Macintosh
Install
12
When Presto! PageManager is installed OCR
capability is added to Brother ControlCenter2. You
can easily scan, share and organize photos and
documents using Presto! PageManager.
a Double-click Presto! PageManager and follow
Presto! PageManager
the on-screen instructions.
• Enter a name for your Macintosh in
Display Name up to 15 characters long and
click OK. Go to f.
• If you want to use the machine’s Scan key to
scan over the network, you must check the
Register your computer with the “Scan To”
function on the machine box.
• The name you enter will appear on the
machine’s LCD when you press and
choose a scan option. (For more information,
see Network Scanning in the Software User’s
Guide on the CD-ROM.)
Install MFL-Pro Suite on
additional computers
13
If you want to use your machine with multiple
computers on the network, install MFL-Pro Suite on
each computer. Go to step 11 on page 21.
Finish
(if needed)
The installation is now
complete.
f When this screen appears, click OK.
The installation of MFL-Pro Suite is now
complete.
Go to step 12 on page 22.
22
For Network Users
BRAdmin Light utility (for Windows® users)
BRAdmin Light is a utility for initial setup of Brother network connected devices. It also can search for Brother
products on your network, view the status and configure basic network settings, such as IP address.
For more information on BRAdmin Light, visit us at http://solutions.brother.com/
Note
If you require more advanced printer management, use the latest Brother BRAdmin Professional utility version
that is available as a download from http://solutions.brother.com/
.
.
Install the BRAdmin Light configuration utility
a Click Network Utilities on the menu screen.
b Click BRAdmin Light and follow the on-screen
instructions.
Set your IP address, Subnet Mask and Gateway using BRAdmin Light
Note
If you have a DHCP/BOOTP/RARP server in your
network, you do not have to do the following
operation. The machine will automatically obtain
its own IP address.
a Start BRAdmin Light. It will search for new
devices automatically.
b Double-click the unconfigured device.
Note
The default password for the machine is ‘access’.
You can use BRAdmin Light to change this
password.
c Choose STATIC for the Boot Method. Enter
the IP Address, Subnet Mask and Gateway,
and then click OK.
d The address information will be saved to the
machine.
23
For Network Users
BRAdmin Light utility (for Mac OS X users)
BRAdmin Light is a utility for initial setup of Brother network connected devices. It also can search for Brother
products on your network, view the status and configure basic network settings, such as IP address from a
computer running Mac OS X 10.3.9 or greater.
The BRAdmin Light software will be installed automatically when you install the printer driver. If you have already
installed the printer driver, you do not have to install BRAdmin Light again. For more information on BRAdmin
Light, visit us at http://solutions.brother.com/
.
Set your IP address, Subnet Mask and Gateway using BRAdmin Light
Note
• If you have a DHCP/BOOTP/RARP server in
your network, you do not have to do the
following operation. The machine will
automatically obtain its own IP address.
• Make sure that version 1.4.2 or greater of
Java™ client software is installed on your
computer.
• The default password for the machine is
‘access’. You can use BRAdmin Light to
change this password.
a Double-click Macintosh HD on your desktop.
c Double-click the file BRAdmin Light.jar and
run the software. BRAdmin Light will then
search for new devices automatically.
d Double-click the unconfigured device.
b Choose Library, Printers, Brother and then
Utilities.
e Choose STATIC for Boot Method. Enter the
IP Address, Subnet Mask and Gateway, and
then click OK.
f The address information will be saved to the
machine.
24
For Network Users
Web Based Management (web browser)
The Brother print server is equipped with a web server
that allows you to monitor its status or change some
of its configuration settings, using HTTP (Hyper Text
Transfer Protocol).
Note
• The User Name is ‘admin’ and the default
password is ‘access’. You can use a web
browser to change this password.
• We recommend Microsoft
6.0 (or higher) or Firefox 1.0 (or higher) for
Windows
Please also make sure that JavaScript and
cookies are always enabled in whichever
browser you use. To use a web browser, you
will need to know the IP address of the print
server. The IP address of the print server is
listed on the Network Configuration List.
®
and Safari 1.3 for Macintosh.
®
Internet Explorer®
a Open your browser.
b Type http:// printer_ip_address /into your
browser (Where “printer_ip_address” is the IP
address of the printer or the print server name).
For example http://192.168.1.2/
Print the Network Configuration List
You can print the Network Configuration List to
confirm the current network settings. To print the
Network Configuration List:
a Turn on the machine and wait until the machine
is in the Ready state.
b Press Menu, 5, 4.
Machine Info.
4.Network Config
c Press Start.
The machine will print the current network
settings.
Restore the network settings to factory default
To restore all network settings of the internal
Print/Scan server to factory default, please follow the
steps below.
a Make sure the machine is not operating, then
disconnect all the cables from the machine
(except the power cord).
See Chapter 11 of the Network User’s Guide.
b Press Menu, 4, 0.
Network
0.Network Reset
c Press 1 to choose Reset.
d Press 1 to choose Yes.
e The machine will restart, re-connect cables
once this is complete.
25
Other Information
Choosing a location
Put your machine on a flat, level, stable surface that is free of vibration and shocks, such as a desk. Put the
machine near a standard grounded electrical socket. Choose a location where the temperature remains between
10 °C and 32.5 °C and the humidity is between 20% to 80% (without condensation).
WARNING
• DO NOT expose the machine to direct sunlight, excessive heat, open flames, salty or corrosive
gasses, moisture or dust.
• DO NOT place the machine near heaters, air conditioners, refrigerators, water or chemicals.
CAUTION
CAUTION
• Avoid placing your machine in a high-traffic area.
• Avoid placing your machine on a carpet.
• DO NOT connect your machine to electrical sockets controlled by wall switches or automatic timers,
or to the same circuit as large appliances that might disrupt the power supply.
• Disruption of power can delete information from the machine’s memory.
• Make sure cables leading to the machine do not constitute a trip hazard.
26
Other Information
To use the machine safely
Please keep these instructions for later reference and read them before attempting any maintenance.
WARNING
There are high voltage electrodes inside the machine.
Before you clean the inside of the machine, make sure you
have unplugged the power cord from the electrical socket.
Doing this will prevent an electrical shock.
DO NOT handle the plug with wet hands. Doing this might
cause an electrical shock.
Always make sure the plug is fully inserted.
This product must be installed near an electrical socket
that is easily accessible. In case of an emergency, you
must unplug the power cord from the electrical socket to
shut off the power completely.
DO NOT use flammable substances near the machine. DO
NOT use any type of spray to clean the inside or outside
of the machine. Doing this may cause a fire or electrical
shock. Refer to Routine maintenance in the User’s Guide
for how to clean the machine.
DO NOT use a vacuum cleaner to clean up scattered toner.
Doing this might cause the toner dust to ignite inside the
vacuum cleaner, potentially starting a fire. Please
carefully clean the toner dust with a dry, lint-free soft cloth
and dispose of it according to local regulations.
27
Other Information
CAUTION
CAUTION
After you have just used the machine, some internal parts
of the machine will be extremely hot. To prevent injury,
when you open the top or back cover (back output tray) of
the machine, DO NOT touch the shaded parts shown in the
illustration.
To prevent injuries, be careful not to put your hands on the
edge of the machine under the document cover, the
scanner, or the top cover as shown in the illustrations.
To prevent injuries, be careful not to put your fingers in
the areas shown in the illustrations.
IMPORTANT
The fuser unit is marked with a caution label. Please DO
NOT remove or damage the label.
28
Other Information
Regulations
EC Declaration of Conformity
Disconnect device
This product must be installed near an electrical
socket that is easily accessible. In case of
emergencies, you must disconnect the power cord
from the electrical socket to shut off power
completely.
Radio interference
This product complies with EN55022 (CISPR
Publication 22)/Class B.
EU Directive 2002/96/EC and EN50419
This equipment is marked with the above recycling
symbol. It means that all the end of the life of the
equipment you must dispose of it separately at an
appropriate collection point and not place it in the
normal domestic unsorted waste stream. This will
benefit the environment for all. (European Union only)
International ENERGY STAR
Statement
The purpose of the International ENERGY STAR
Program is to promote the development and
popularization of energy-efficient office equipment.
As an ENERGY STAR
Ltd. has determined that this product meets the
ENERGY STAR
®
®
specifications for energy efficiency.
®
Qualification
®
Partner, Brother Industries,
Wiring information (U.K. only)
If you need to replace the plug fuse, fit a fuse that is
approved by ASTA to BS1362 with the same rating as
the original fuse.
Always replace the fuse cover. Never use a plug that
does not have a cover. If in any doubt, call a qualified
electrician.
Warning - This machine must be earthed. (U.K. only)
The wires in the mains lead are coloured in line with
the following code:
Green and Yellow: Earth
Blue: Neutral
Brown: Live
LAN connection
CAUTION
CAUTION
DO NOT connect this product to a LAN connection
that is subject to over-voltages.
29
Options and Consumables
Options
The machine has the following optional accessory. You can expand the capabilities of the machine by adding this
item. For more information about compatible SO-DIMM Memory, visit us at http://solutions.brother.com/
For installing the SO-DIMM Memory, see the User's Guide or visit http://solutions.brother.com/.
SO-DIMM Memory
You can expand the memory by installing
a (144-pin SO-DIMM) memory module.
When the time comes to replace consumable items, an error will be indicated by the LCD on the control panel. For
more information about the consumables for your machine, visit us at http://solutions.brother.com/
local Brother reseller.
.
or contact your
Toner cartridges Drum units
TN-230C/TN-230M/TN-230Y/TN-230BK
Belt Unit (BU-200CL) Waste Toner Box (WT-200CL)
1
Contains a set of three colour dr ums and one black drum. All four drums are replaced at the same time.
DR-230CL
1
30
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
Multi-Function Link is a registered trademark of Brother International Corporation.
Windows Vista is either a registered trademark or a trademark of Microsoft Corporation in the United States and/or other countries.
Microsoft, Windows and Windows Server and Internet Explorer are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
Apple, Macintosh, Safari and TrueType are trademarks of Apple Inc., registered in the United States and other countries.
Nuance, the Nuance logo, PaperPort and ScanSoft are trademarks or registered trademarks of Nuance Communications, Inc. or its affiliates
in the United States and/or other countries.
Each company whose software title is mentioned in this manual has a Software License Agreement specific to its proprietary programs.
All other brand and product names mentioned in this manual are trademarks or registered trademarks of their
respective companies.
Compilation and Publication
Under the supervision of Brother Industries, Ltd., this manual has been compiled and published, covering the latest product descriptions and
specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for
any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other
errors relating to the publication.
Copyright and License
©2009 Brother Industries, Ltd.
This product includes software developed by the following vendors:
©1983-1998 PACIFIC SOFTWORKS, INC.
This product includes the “KASAGO TCP/IP” software developed by ELMIC WESCOM, Inc.
©2009 Devicescape Software, Inc.
Loading...