Brother DCP-8060 User Manual

DCP-8060

DCP-8065DN

Before you can use the machine, you must set up the hardware and install the software. Please read this “Quick Setup Guide” for the correct setup procedure and installation instructions.

Step 1

Setting Up the machine

Setting Up

the machine

USB

Windows

Step 2

Installing the Drivers & Software

Setup is Complete!

Keep this “Quick Setup Guide”, User’s Guide and supplied CD-ROM in a convenient place for quick and easy reference at all times.

Parallel

Windows

4.0

Parallel

Windows

Network

Windows

Installing the Drivers & Software

USB

Macintosh

Quick Setup Guide

Version A

Network

Macintosh

Network

Administrators

Warning Caution Improper Setup Note User’s Guide

Warnings tell you what to do to prevent possible personal injury.

Cautions specify procedures you must follow or avoid to prevent possible damage to the machine or other objects.

Improper Setup icons alert you to devices and operations that are not compatible with the machine.

Notes tell you how you should respond to a situation that may arise or give tips about how the current operation works with other features.

Indicates reference to the User’s Guide.

■ Getting Started

Carton Components

8 7

. Automatic Document Feeder (ADF)

. Control Panel

. Face-down Output Tray

Support Flap (Support Flap)

. Front Cover

Carton components may differ from one country to another. Save all packing materials and the carton.

Austraria & New Zealand users: Hong Kong, Malaysia & Singapore users:

. Paper Tray

. Power Switch

. Document Cover

. ADF Document Output Support Flap

Quick Setup Guide

CD-ROMs

For Windows

For Macintosh

AC Power Cord

Drum Unit Assembly

(including Toner

Cartridge)

The mains plug supplied with this machine is a grounded three pin plug. Make sure that the AC socket will accept this grounded three pin plug. This machine must be grounded, If in doubt, call a qualified electrician.

Philipine & Thailand users:

The mains plug supplied with this machine is a side grounded two pin plug. Make sure that the AC socket will accept this side grounded two pin plug. This machine must be grounded, If in doubt, call a qualified electrician.

■ To ensure safe operation the supplied plug must be inserted only into a standard power outlet that is

properly grounded through the standard electrical wiring. None grounded equipment may cause an electrical shock hazard, and may cause excessive electrical noise radiation.

■ The interface cable is not a standard accessory. Please purchase the appropriate interface cable for

the interface you intend to use (Parallel, USB or Network).

■ Do NOT connect the interface cable at this time. Connecting the interface cable is done during the

software installation process.

■ USB interface cable

Please make sure you use a USB 2.0 interface cable that is no longer than 2.0 meters. When you use a USB cable, make sure you connect it to the USB port of your computer and not to a USB port on a keyboard or non-powered USB hub.

■ Parallel interface cable

Please make sure you use a Parallel interface cable that is no longer than 2.0 meters. Use a shielded interface cable that is IEEE 1284-compliant.

■ Network cable (DCP-8065DN only)

Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or 100Base-TX Fast Ethernet Network.

Control Panel

DCP-8060

1234

879

DCP-8065DN

1234

879

1 Status LED 2 LCD (Liquid Crystal Display) 3 Menu keys

4 Dial Pad 5 Stop/Exit key 6 Start key

7 Copy keys 8 Scan key 9 Print keys

For the details of the control panel, see “Control panel overview” in Chapter 1 of the User’s Guide.

Step 1

Step 2

Supplied CD-ROM “MFL-Pro Suite” ................................................................................8

For USB Interface Cable Users (For Windows For Parallel Interface Cable Users (For Windows For Windows NT For Network Interface Cable Users (DCP-8065DN only) (For Windows® 98/98SE/Me/NT/2000 Professional/XP/XP Professional x64 Edition)

For USB Interface Cable Users ......................................................................................20

For Network Interface Cable Users (DCP-8065DN only) .............................................25

Setting Up the machine

1. Install the Drum Unit and Toner Cartridge Assembly ....................................4

2. Load Paper in the Paper Tray ..........................................................................5

3. Release the Scanner Lock ................................................................................6

4. Connect the Power Cord ..................................................................................6

5. Setting the LCD Contrast .................................................................................7

Installing the Drivers & Software

98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition) ....10

98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition) ....12

Workstation Version 4.0 Users ......................................................15

For Mac OS® 9.1 to 9.2 ......................................................................................20

■

For Mac OS® X 10.2.4 or greater .......................................................................22

■

For Mac OS® 9.1 to 9.2 ......................................................................................25

■

For Mac OS® X 10.2.4 or greater .......................................................................27

■

...17

For Network Users and Administrators (DCP-8065DN only)

■

BRAdmin Professional configuration utility (For Windows® users) ..........................30

BRAdmin Light configuration utility (For Mac OS

Options and Consumables

■

Options ............................................................................................................................33

Replacement Consumables ...........................................................................................33

X users) ......................................32

Step 1

1 Install the Drum Unit and Toner Cartridge Assembly

Setting Up the machine

Do not connect the interface cable. Connecting the interface cable is done during the software installation process.

Open the front cover by pressing the front cover release button (1).

Unpack the drum unit and toner cartridge assembly.

Gently rock it from side to side several times to distribute the toner evenly inside the cartridge.

(1)

Put the drum unit and toner cartridge into the machine so that it clicks into place.

Close the front cover of the machine.

2 Load Paper in the Paper Tray

Pull the paper tray completely out of the machine.

While pressing the blue paper guide release lever (1), slide the adjusters to fit the paper size. Check that the guides are firmly in the slots.

Put paper in the paper tray. Check that the paper is flat in the tray and below the maximum paper mark (1).

Put the paper tray firmly back into the machine and unfold the support flap (1) before you use the machine.

(1)

Setting Up

the machine

USB

Windows

Parallel

Windows

4.0

Parallel

Windows

(1)

Fan the stack of paper well to avoid paper jams and misfeeds.

(1)

For details on supported paper specifications, see “Acceptable paper and other media” in Chapter 2 of the User’s Guide.

Windows

Macintosh

Network

USB

Network

Administrators

Step 1

Setting Up the machine

Release the Scanner

Lock

Push the lever (1) in the direction shown to unlock the scanner. (The gray scanner lock lever is located at the back left side, under the document cover (2).)

(1)

(2)

4 Connect the Power Cord

Do not connect the Parallel or USB cable yet.

Make sure that the power switch is off. Connect the AC power cord to the machine.

Plug the AC power cord into an AC outlet. Turn the power switch on.

If Scanner Locked appears on the LCD, immediately release the scanner lock and press Stop/Exit. (See “Release the Scanner Lock” on page 6.)

5 Setting the LCD Contrast

You can change the contrast to help the LCD look lighter or darker.

Press Menu.

Press 1.

Press 6.

Press to increase the contrast. —OR— Press to decrease the contrast. Press OK.

Setting Up

the machine

USB

Windows

Parallel

Windows

4.0

Windows

Macintosh

Parallel

Network

USB

Network

Go to the next page to install the drivers & software

Network

Administrators

Step 2

The CD-ROM includes the following items:

Installing the Drivers & Software

Supplied CD-ROM “MFL-Pro Suite”

Install MFL-Pro Suite

You can install the MFL-Pro Suite and multifunction drivers.

Install Optional Applications

You can install additional MFL-Pro Suite software utilities.

Documentation

View the User’s Guide and other documents in PDF format (Viewer included). The User’s Guide on the CD-ROM includes the Software and Network User’s Guide for features available when connected to a computer (e.g. printing, scanning and networking details). .

On-Line Registration

You will be pointed to the Brother Product Registration Web page for quick registration of your machine.

Brother Solutions Center

Brother contact information and web site links offering the latest news and support information.

Repair MFL-Pro Suite

(For USB and Parallel cable users only) If you experience errors while installing the MFL-Pro Suite, you can use this function to automatically repair and re-install the software.

MFL-Pro Suite includes Printer Driver, Scanner Driver, Brother ControlCenter2, ScanSoft True Type PaperPort application for viewing scanned documents.

PaperPort® SE with OCR and

fonts.

SE is a document management

Start Here OS 9.1-9.2

You can install the printer driver, scanner driver and Presto!

You can install the MFL-Pro Suite that includes the printer driver, scanner driver and the Brother ControlCenter2 for Mac OS can also install Presto! capability to the Brother ControlCenter2 and easily scan, share and organize photos and documents.

You can get important information and troubleshooting tips.

View the User’s Guide and other document in PDF format (Viewer included). The User’s Guide on the CD-ROM includes the Software and Network User’s Guide for features available when connected to a computer (e.g. printing, scanning and networking details).

You can access the Brother Solutions Center, a Web site offering information about your Brother product including FAQs, User’s Guides, Driver updates and Tips for using your machine.

You will be pointed to the Brother Product Registration Web Page for quick registration of your machine.

PageManager® for Mac OS®9.1 - 9.2.

Start Here OSX

10.2.4 or greater. You

PageManager® to add OCR

Readme.html

Documentation

Brother Solutions Center

On-Line Registration

Step 2

Follow the instructions on this page for your operating system and interface cable. For the latest drivers and to find the best solution for your problem or question, access the Brother Solutions Center directly from the driver or go to http://solutions.brother.com

Installing the Drivers & Software

Setting Up

the machine

USB Interface Cable Users .......................................... Go to page 10

(For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition)

Parallel Interface Cable Users ..................................... Go to page 12

(For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition)

Windows NT® Workstation Version 4.0 Users ........... Go to page 15

(For Parallel Interface Cable Users)

Network Interface Cable Users.................................... Go to page 17

(DCP-8065DN only)

USB

Windows

Parallel

Windows

4.0

Parallel

Windows

Network

Windows

USB Interface Cable Users

■ For Mac OS

9.1 to 9.2 ............................................. Go to page 20

X 10.2.4 or greater ............................. Go to page 22

Network Interface Cable Users (DCP-8065DN only)

■ For Mac OS

9.1 to 9.2 ............................................. Go to page 25

X 10.2.4 or greater ............................. Go to page 27

For Network Users and Administrators...................... Go to page 30

USB

Macintosh

Network

Macintosh

Network

Administrators

Step 2

For USB Interface Cable Users

(For Windows® 98/98SE/Me/2000 Professional/XP/XP Professional x64 Edition)

Make sure that you have finished the instructions from Step 1 “Setting Up the machine” on pages 4 - 7.

Installing the Drivers & Software

Please close any applications running before installing the MFL-Pro Suite.

Switch off the machine and disconnect the machine from the power socket (and from your computer, if you have already connected an interface cable).

After reading and accepting the ScanSoft® PaperPort Yes.

SE License Agreement, click

Turn on your computer. (For Windows XP Professional x64 Edition, you must be logged on with Administrator rights.)

Put the supplied CD-ROM for Windows® into your CD-ROM drive. If the model name screen appears, choose your machine. If the language screen appears, choose your language.

The CD-ROM main menu will appear. Click Install MFL-Pro Suite.

2000 Professional/XP/

The installation of PaperPort automatically start and is followed by the installation of MFL-Pro Suite.

When the Brother MFL-Pro Suite Software License Agreement window appears, click Yes if you agree to the Software License Agreement.

Choose Standard (DCP-8060) or Local Connection (DCP-8065DN), and then click Next. The installation continues.

SE will

If this window does not appear, use Windows® Explorer to run the setup.exe program from the root folder of the Brother CD-ROM.

(DCP-8060) (DCP-8065DN)

If you want to install the PS driver (BR-Script 3 printer driver), choose Custom Install and then follow the on-screen instructions. When the Select Components screen appears, check PS Printer Driver, and then continue following the on-screen instructions.

+ 25 hidden pages

Brother DCP-8060 User Manual

■ Getting Started

Carton Components

Control Panel

Table of Contents

1 Install the Drum Unit and Toner Cartridge Assembly

2 Load Paper in the Paper Tray

4 Connect the Power Cord

5 Setting the LCD Contrast

Supplied CD-ROM “MFL-Pro Suite”