Bosch Power Tools GLM165-22, GLM165-27C User manual

IMPORTANT:

0.0°

Read Before Using

Operating/Safety Instructions

GLM165-22
GLM165-27C

1/x

164

'

6

" ⁄

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

(9)

(a) (d) (e)

(g)

(f)

164' 6

(3)

(2)

(1)

1/x

(b)

4'02"

8'05"

12'08"

" ⁄

164

(8)

'

6

" ⁄

(7)

12'08"

8'05"

(6)

4'02"

(4)

(5)

GLM165-22

-2-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

(b)

(a) (c) (d)(e)

(9)

(1)

(h)

(g)

(f)

(2)

(3)

0.0°

164' 6

1/x

4'02"

8'05"

12'08"

" ⁄

0.0°

164

'

6

" ⁄

(8)

GLM165-27C

(7)

12'08"

8'05"

(6)

4'02"

(4)

(5)

-3-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

(11)

(12)

3601K72S10

GLM165-22

(13)

Made in Malaysia

Mount Prospect, IL

Robert Bosch Tool Corp.,

CLASSE 2.

2 x 1.5V (AA)

DUIT LASER DE

LE FAISCEAU. PRO-

RECTEMENT DANS

GARDEZ PAS DI-

LASER. NE RE-

RAYONNEMENT

LASER PRODUCT.

BEAM. CLASS 2

2

DO NOT STARE INTO

LASER RADIATION.

< 1 mW, 635 nm

IEC 60825-1:2014

A

(16)

(15)

(14)

(10)

(24)

(26)

(25)

(27)

-4-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

AC

B

GLM165-22

(i) (j) (k)

GLM165-27C

(i) (j) (k)

1/x

1/x

1/x

-5-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

D

(18)

(17)

(17)

(18)

-6-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

E

(19)

(17)

(18)

(20)

(21)

-7-

(23)

1.600.A01.6A8

C

l

0

a
n
o
i

M 5

s

GL

fes

o
r
P

(22)

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Safety Symbols

The definitions below describe the level of severity for
each signal word. Please read the manual and pay
attention to these symbols.

This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that follow
this symbol to avoid possible
injury or death.

DANGER indicates a
hazardous situation which,
if not avoided, will result in
death or serious injury.

WARNING indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.

CAUTION indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.

-8-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

General Safety Rules

Read all instructions. Failure to

may result in hazardous radiation exposure, electric
shock, fire and/or serious injury.

The term “laser measure” in the warnings listed below
refers to your battery-operated (cordless) laser mea­suring tool.

SAVE ALL WARNINGS AND INSTRUCTIONS

The following label is on your laser
measure for your safety. ALWAYS BE
AWARE of its location when using the
laser measure.

tion and complies with 21 CFR 1040.10 and 1040.11
except for conformance with IEC 60825-1 Ed. 3.,
as described in Laser Notice No. 56, dated May 8,

2019.” This can lead to persons being blinded.

DO NOT stare directly at the laser beam or project
the laser beam directly into the eyes of others. Seri-

ous eye injury could result.

DO NOT place the laser measure in a position that
may cause anyone to stare into the laser beam inten­tionally or unintentionally. Serious eye injury could

result.

DO NOT operate the laser measure around children
or allow children to operate the laser measure. Seri-

ous eye injury could result.

ALWAYS: Make sure that any bystanders in the vicin­ity of use are made aware of the dangers of looking
directly into the laser measure.

Never aim the beam at a workpiece with a reflective
surface. Bright shiny reflective sheet steel or similar

follow all instructions listed below

FOR FUTURE REFERENCE

DO NOT direct the laser beam
at persons or animals and do
not stare into the laser beam
yourself. This laser measure
produces class 2 laser radia-

-9-

2

IEC 60825-1:2014
< 1 mW, 635 nm
LASER RADIATION.
DO NOT STARE INTO
BEAM. CLASS 2
LASER PRODUCT.
RAYONNEMENT
LASER. NE RE­GARDEZ PAS DI­RECTEMENT DANS
LE FAISCEAU. PRO­DUIT LASER DE
CLASSE 2.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

reflective surfaces are not recommended for laser
use. Reflective surfaces could direct the beam back

towards the operator.

Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.

DO NOT use any optical tools such as, but not limited
to, telescopes or transits to view the laser beam. Se-

rious eye injury could result.

DO NOT leave the laser measure “ON” unattended in
any operation mode. ALWAYS turn the laser measure
“OFF” when not in use. Leaving the laser measure

“ON” increases the risk of someone inadvertently star­ing into the laser beam.

DO NOT operate the laser measure in combustible
areas such as in the presence of flammable liquids,
gases or dust.

Do not use the laser viewing glasses as safety gog­gles. The laser viewing glasses are used for improved

visualization of the laser beam, but they do not protect
against laser radiation.

Do not use the laser viewing glasses as sun glasses
or in traffic. The laser viewing glasses do not afford

complete UV protection and reduce color perception.
ALWAYS position the laser measure securely. Dam-

age to the laser measure and/or serious injury to the
user could result if the laser measure falls.

Take care to recognize the accuracy and range of the
laser measure. Measurement may not be accurate if

used beyond the rated range of the laser measure.

DO NOT remove or deface any warning or caution
labels. Removing labels increases the risk of exposure

to laser radiation.

Battery tool use and care

Recharge only with the charger specified by the man­ufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with
another battery pack.

-10-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Use tool only with specifically designated battery
packs. Use of any other battery packs may create a

risk of injury and fire.

When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.

Shorting the battery terminals together may cause
burns or a fire.

Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acciden­tally occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from

the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or
modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, EXPLOSION
or risk of injury.

Do not expose a battery pack or tool to fire or ex­cessive temperature. Exposure to fire or temperature

above 265 °F (130 °C) may cause explosion.

Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging improp-

erly or at temperatures outside the specified range
may damage the BATTERY and increase the risk of fire.

Disconnect the battery pack from the tool before
making any adjustments, changing accessories, or
storing the tool. Such preventive safety measures re-

duce the risk of starting the tool accidentally.

Do not modify or attempt to repair the tool or the
battery pack except as indicated in the instructions
for use and care.

Electrical safety

Batteries can explode or leak,

risk, always follow all instructions and warnings on the
battery label and package.

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

cause injury or fire. To reduce this

-11-

DO NOT short any battery terminals.
DO NOT charge alkaline batteries.
DO NOT mix old and new batteries. Replace all of

them at the same time with new batteries of the
same brand and type.

DO NOT mix battery chemistries.
Dispose of or recycle batteries per local code.
DO NOT dispose of batteries in fire.
Keep batteries out of reach of children.
Remove batteries if the device will not be used for

several months.

Risk of fire and burns. Do not

(70°C) or incinerate.

open, crush or heat above 158°F

Maintenance

DO NOT disassemble the laser measure. There are
no user serviceable parts inside. Disassembling the
laser will void all warranties on the product. Do not
modify the product in any way. Modifying the laser

measure may result in hazardous laser radiation expo­sure.

ALWAYS remove the batteries when cleaning the la­ser light aperture to laser lens.

DO NOT use this laser measure for any purpose other
than those outlined in this manual. This could result

in serious injury.

ALWAYS use only the accessories that are recom­mended by the manufacturer of your laser measure.

Use of accessories that have been designed for use
with other laser measures could result in serious in­jury.

Repair and servicing must always be performed by
a qualified repair facility. Repairs performed by un-

qualified personnel could result in serious injury.

-12-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Bluetooth® (GLM165-27C only)

Do not turn on laser remotely using

to the laser tool. The sudden bright laser beam may

increase the risk of personal injury or property damage.

Do not use the laser measure with Bluetooth® in
the vicinity of gas stations, chemical plants, areas
where there is danger of explosion and areas sub­ject to blasting. Do not use the laser measure with
Bluetooth® in airplanes. Do not use the laser measure
with Bluetooth® in the vicinity of medical devices.
Avoid operation in the direct vicinity of the human
body over longer periods of time. When using the la-

ser measure with Bluetooth®, interference with other
devices and systems, airplanes and medical devices
(e.g., cardiac pacemakers, hearing aids) may occur.

The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use
of such marks by Robert Bosch Tool Corporation is
under license.

device manufacturer. Failure to follow recommended
procedures could result in personal injury or property
damage.

the Bosch app without line of sight

Follow all instructions and warn­ings provided by your Bluetooth®

FCC Caution

The manufacturer is not responsible for radio inter­ference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s
authority to operate the equipment.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1) This device may not cause harmful interference,
and

2) This device must accept any interference received,
including interference that may cause undesired
operation.

-13-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

NOTE! This equipment has been tested and found to
comply with the limits for a Class B digital devices,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates uses and can radiate radio fre­quency energy and, if not installed and used in ac­cordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

•Reorientorrelocatethereceivingantenna.

•Increasetheseparationbetweentheequipmentand

receiver.

•Connecttheequipmentintoanoutletonacircuitdif-

ferent from that to which the receiver is connected.

•Consultthedealeroranexperiencedradio/TVtech-

nician for help.

“Exposure to Radio Frequency (RF) Signals: The wire­less device is a radio transmitter and receiver. It is
designed and manufactured not to exceed the emis­sion limit for exposure to radio frequency (RF) energy
set by the Ministry of Health (Canada), Safety Code

6. These limits are part of comprehensive guidelines

and established permitted levels of RF energy for the
general population.

These guidelines are based on the safety standards
previously set by international standard bodies. These
standards include a substantial safety margin de­signed to assure the safety of all persons, regardless
of age and health.

-14-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ISED Canada

This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two con­ditions:

(1) this device may not cause interference, and
(2) this device must accept any interference, including

interference that may cause undesired operation
of the device.

Symbols

IMPORTANT: Some of the following symbols may be

used on your laser measure. Please study them and
learn their meaning. Proper interpretation of these
symbols will allow you to operate the laser measure
better and safer.

Symbol Designation/Explanation

Read manual symbol, alerts user to read
manual

This symbol designates that this laser
measure complies with Part 15 of the
FCC Rules.

Laser warning symbol, alerts user to
laser radiation, do not stare into beam.

-15-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Technical Data

Laser Measure GLM165-22, GLM165-27C

Article Number 3.601.K72.S10

Measuring range (typical): 6 in – 165 ft

Measuring accuracy (typical)

Lowest indication unit 1/32 in (0.8 mm)

General

Operating temperature +14 °F to 113 °F

Storage temperature -4 °F to 158 °F

Relative air humidity, max. 90 %

Max. altitude: 2000 m

Pollution degree according to
IEC 61010-1:

Laser class 2

Laser type 635 nm, <1 mW

Laser beam diameter at 77 °F
(25 °C) approx.

– at 33 ft (10 m) distance
– at 165 ft (50 m) distance

Weight 0.22 lb (0.1 kg)

Dimensions 4.7 x 2.1 x 1.2 in

Automatic switch-off after approx.
– Laser
– Laser measure (without

measurement)

3.601.K72.T10

(0.15 – 50 m)

A

±1/16 in (±1.6 mm)

(-10 °C to 45 °C)

(-20 °C to 70 °C)

D

2

4/11 in (9 mm)
1-3/4 in (45 mm)

(119x53x29 mm)

E

20 s
5 min F

B

C

-16-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Degree of protection IP65

Batteries 2 x 1,5 V LR6 (AA)

Battery pack (optional) Li-ion

Type BA 3.7V 1.0Ah A

Article Number 1 607 A35 0N9

USB port Type C

Rated voltage 3.7 V

Capacity 1.0 Ah

Number of battery cells 1

Power adaptor (optional)

Output voltage 5.0 V

Output current 500 mA

Recommended power adaptor 1 600 A01 43H

Laser Measure GLM165-27C only

Indirect Distance Measurement and Vial

Measuring range 0°–360° (4 x 90°)

Angle Measurement

Measuring range 0°–360° (4 x 90°)

Measuring accuracy (typical) ±0.2°

G,H, I

Lowest indication unit 0.1°

Data transmission

Bluetooth® Bluetooth® 4.2

(Low Energy)

J

A

The working range increases depending on how well

the laser light is reflected from the surface of the
target (scattered, not reflective) and with increased
brightness of the laser point to the ambient light
intensity (interior spaces, twilight). In unfavorable

-17-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

conditions, e.g., with extreme illumination or a badly
reflecting surface, the measuring range may be lim­ited.

B

In favorable conditions, a deviation influence of ±0.05

mm/m must be taken into account. In unfavorable
conditions, e.g., with extreme illumination, badly re­flecting surface or the room temperature deviating
heavily from 77 °F (25 °C), the maximum deviation
can be up to ±3.0 mm. Additionally, a deviation influ­ence of 0.15 mm/m must be taken into account.

C

In the real time measuring function, the maximum

operating temperature is 104 °F (40 °C).

D

Non-conductive soiling only, whereby occasional

temporary conductivity caused by condensation is
expected.

E

Shut-off after approximately 5 minutes in the real

time measuring function

F

Bluetooth® deactivated

G

After user calibration at 0 ° and 90 °; An additional

grade error of ±0.01 °/degree to 45 ° (max.) has to be
taken into account.

H

Left side of the tool is the reference side for inclination

measurement.

I

At 77 °F (25 °C ) operating temperature.

J

Bluetooth® devices must support the GATT profile.

The laser measure can be clearly identified with the
serial number (11) on the type plate.

Intended Use

The laser measure is intended for measuring distanc­es, lengths, heights and clearances. The laser measure
is suitable for measuring indoors.

-18-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Features

The numbering of the product features shown refers
to the illustration of the laser measure on the graphic
page.

(1) Rounding button [ ]
(2) Function button

[Func]

(3) Minus button [−]
(4) Display
(5) Measuring button [ ]
(6) Plus button [+]
(7) Basic settings

button [ ]

(8) On/off button [ ]
(9) Loop for carrying

strap

A)

(10) Laser warning label
(11) Serial number
(12) Battery

compartment cover
locking mechanism

(14) 1/4” tripod socket
(15) Reception lens
(16) Laser beam output
(17) Belt clip

A)

(18) Screw for belt clip
(19) Laser target plate
(20) Laser viewing

(21) Tripod

glasses

A)

A)

(22) Protective bag
(23) USB-C cable

A)

(24) Li-ion battery pack
(25) Li-ion battery pack

locking mechanism

(26) USB-C port cover
(27) Battery port

A)

A)

(13) Battery

compartment cover

A) Accessories shown or described are not included

with the product as standard. You can find
the complete selection of accessories in our
accessories range.

A)

A)

A)

-19-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Display elements

(a) Reference level of measurement
(b) Rounding function accuracy reference
(c) Connection status (GLM165-27C only)

Bluetooth® activated,
no connection established

Bluetooth® activated,
connection established

(d) Battery indicator
(e) Measured-value lines
(f) Result line
(g) Measuring function
(h) Slope angle display (GLM165-27C only)
(i) Display measuring functions
(j) Display settings
(k) Display more settings

-20-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Preparation

Power Supply

The tool can either be operated with commercially
available LR6 (AA) batteries or with the Bosch re­chargeable Lithium-ion battery pack (optional) out­lined in the technical section of this manual.

Operation with LR6 (AA) batteries

Alkaline batteries (2 x 1,5 V LR6 (AA)) are recommend­ed for the laser measure.

Press the locking mechanism (12) to open the battery
compartment cover (13) and remove the battery com­partment cover. Insert the batteries. When inserting,
pay attention to the correct polarity according to the
representation on the inside of the battery compart­ment.

When the empty battery symbol first appears on the
display, then approximately 100 measurements are
still possible. When the battery symbol is empty and
red flashing, measurements are no longer possible.
Replace the batteries.

Always replace all batteries at the same time. Only
use batteries from one brand and with identical ca­pacity.

Remove the batteries from the laser measure when
not using it for extended periods. When storing for

extended periods, the batteries can corrode and dis­charge themselves.

Operation with Bosch rechargeable lithium-ion

battery packs (optional) (see figure C)

Follow all warnings and all instruc-

lithium-ion battery pack manual before using the bat­tery pack. Improper usage and recharge of battery

pack may increase the risk of fire, personal injury and
property damage.

tions in the Bosch rechargeable

Use only Bosch rechargeable lithi­um-ion battery packs listed in the

-21-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

technical data section of this manual. Use of other
battery packs may increase the risk of fire, personal
injury and property damage.

Remove the batteries from the

ed periods. When storing for extended periods, the

batteries can corrode and self-discharge.
Note: The battery pack is supplied partially charged.

To ensure full capacity of the battery pack, completely
charge the battery pack with the USB power adapter
(optional) listed in the technical data section of this
manual before using for the first time. See Bosch re­chargeable lithium-ion battery pack manual for details.

this manual. Use of other USB-C cables may increase
the risk of fire, personal injury and property damage.

The lithium-ion battery pack can be charged at any
time without reducing its service life. Interrupting the
charging procedure does not damage the battery pack.

The lithium-ion battery is protected against deep
discharge by the Electronic Cell Protection (ECP). A
protective circuit switches the laser level off when the
battery is drained.

•Following the automatic shut off of the tool, do not

continue to press the On/Off button. The battery

can be damaged.

To insert the charged battery pack 24, slide it into the
battery port 27 until you feel it lock into position. Do
not use force.

To remove the battery pack 24, press the unlocking
buttons 25 and pull the battery pack out of the battery
port 27. Do not use force.

tool when not using it for extend-

Use only Bosch USB-C cable listed
in the technical data section of

-22-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Operation

Do not leave the switched-on laser

the laser measure off after use. Other persons could

be blinded by the laser beam.

Protect the laser measure against moisture and di­rect sun light.

Do not subject the laser measure to extreme temper­atures or variations in temperature. As an example,

do not leave it in vehicles for a long time. In case of
large variations in temperature, allow the laser mea­sure to adjust to the ambient temperature before put­ting it into operation. In case of extreme temperatures
or variations in temperature, the accuracy of the laser
measure can be impaired.

Avoid heavy impact to or falling down of the laser
measure. After severe exterior effects to the laser

measure, it is recommended to carry out an accuracy
check (see “Accuracy Check of the Distance Measure­ment”, page 25) each time before continuing to work.

– To switch on the measuring tool and the laser,

briefly press the measuring button (5) [

– To switch on the measuring tool without the laser,

briefly press the on/off button (8) [ ].

look into the laser beam yourself, not even from a
large distance.

The values in the memory and the device settings are
retained when you switch the laser measure off.

measure unattended and switch

Switching On and Off

].

Do not point the laser beam at
persons or animals and do not

-23-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Working Advice

The laser measure (GLM165-27C

terface. Local operating restrictions, e.g. in airplanes
or hospitals, are to be observed.

to the laser tool (GLM165-27C only). The sudden bright
laser beam may increase the risk of personal injury or
property damage.

Further information on laser measure and apps can be
found on the Bosch product page by scanning the QR
code on Page 7 or the QR code on the box.

General Information

The reception lens (15) and the laser beam outlet (16)
must not be covered when taking a measurement.

The laser measure must not be moved while taking a
measurement. Therefore, place the laser measure, as
much as possible, against or on a firm stop or support­ing surface.

Influence on the Measuring Range

The measuring range depends on the light conditions
and the reflection properties of the target surface.

Influence on the Measuring Result

Due to physical effects, faulty measurements cannot be
excluded when measuring on different surfaces which
include:

– Transparent surfaces (e.g., glass, water),
– Reflecting surfaces (e.g., polished metal, glass),
– Porous surfaces (e.g. insulation materials),
– Structured surfaces (e.g., roughcast, natural stone).
Also, air layers with varying temperatures or indirectly

received reflections can affect the measured value.

Accuracy Check and Calibration of the Grade
Measurement (GLM165-27C only)

Regularly check the accuracy of the grade measure-

only) is equipped with a radio in-

Do not turn on laser remotely using
the Bosch app without line of sight

-24-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

ment. Hold down the function button (2) [Func]. Press
the plus button (6) [
scroll until the highlighted box appears over the icon

. Press the measure button (5) [ ]. Place the laser

measure on a table or surface and measure the grade.
Turn the laser measure 180° and measure the grade
again. The difference of the indicated reading may not
exceed 0.3°. If the deviation is greater, the laser mea­sure must be recalibrated. Select . Follow the di­rections on the display.

After severe temperature changes or impacts, we rec­ommend to check the accuracy and, if required, to reca­librate the laser measure. After a temperature change,
the laser measure must adjust to the new temperature
before calibrating.

Accuracy Check of the Distance Measurement

The accuracy of the distance measurement can be
checked as follows:

- Select a permanent measuring section with a length

of approx. 10 ft to 33 ft (3 m to 10 m); its length
must be precisely known (e.g. the width of a room
or a door opening). The measuring distance must
be indoors; the target surface for the measurement
must be smooth and reflect well.

- Measure the distance 10 times in a row.

The deviation of the individual measurements from the
mean value must not exceed ± 5/32” (± 4 mm). Log the
measurements so that you can compare their accuracy
at a later point in time.

Working with the Tripod (Accessory)

The tripod is particularly useful for measuring greater
distances. Position the laser measure with 1/4” thread
(14) onto the quick-change plate of a tripod (21).
Tighten the laser measure with the locking screw of the
quick-change plate.

Set the corresponding reference point for the measure­ment with a tripod by pushing the measuring reference
button (5) and using the plus button (6) [
button (3) [ ] to scroll until the highlighted box ap­pears over the .

] or the minus button (3) [ ] to

] and minus

-25-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Error Message

If a measurement is not done correctly, the error mes­sage “Error” appears in the display. Turn the laser
measure off and on again, and start the measurement
again.

The symbol to the left will appear if there is a
fault with the laser measure. If this is the case,
have the laser measure checked by an after
sales service agent for Bosch power tools.

Maintenance and Service

Keep the laser measure clean at
all times.

Do not immerse the laser measure into water or other
fluids.

Wipe off debris using a moist and soft cloth. Do not
use any cleaning agents or solvents.

Maintain the reception lens (14) in particular, with the
same care as required for eye glasses or the lens of a
camera.

If the laser measure should fail despite the care tak­en in manufacturing and testing procedures, repair
should be carried out by an authorized after-sales ser­vice center for Bosch power tools. Do not open the
laser measure yourself.

In all correspondence and spare parts orders, please
always include the 10-digit article number given on the
type plate of the laser measure.

ENVIRONMENT PROTECTION

Recycle raw materials & batteries instead
of disposing of waste. The unit, accesso­ries, packaging & used batteries should
be sorted for environmentally friendly
recycling in accordance with the latest
regulations.

-26-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

LIMITED WARRANTY OF BOSCH

LASER AND LASER MEASURE

PRODUCTS

Robert Bosch Tool Corporation (“Seller”) warrants to
the original purchaser only, that all Bosch lasers and
laser measures will be free from defects in material or
workmanship for a period of one (1) year from date of
purchase. Bosch will extend warranty coverage to two
(2) years when you register your product within eight (8)
weeks after date of purchase. Product registration card
must be complete and mailed to Bosch (postmarked
within eight weeks after date of purchase), or you

Product Registration. If you choose not to register your
product, a one (1) year limited warranty will apply to
your product.

30 Day Money Back Refund or Replacement -

If you are not completely satisfied with the performance
of your laser and laser measures, for any reason, you
can return it to your Bosch dealer within 30 days of
the date of purchase for a full refund or replacement.
To obtain this 30-Day Refund or Replacement, your re­turn must be accompanied by the original receipt for
purchase of the laser or optical instrument product. A
maximum of 2 returns per customer will be permitted.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE
REMEDY under this Limited Warranty and, to the extent
permitted by law, any warranty or condition implied by
law, shall be the repair or replacement of parts, without
charge, which are defective in material or workmanship
and which have not been misused, carelessly handled,
or misrepaired by persons other than Seller or Autho­rized Service Center. To make a claim under this Limited
Warranty, you must return the complete Bosch laser or
laser measure, transportation prepaid, to any BOSCH
Factory Service Center or Authorized Service Center.
Please include a dated proof of purchase with your tool.

-27-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

THIS WARRANTY PROGRAM DOES NOT APPLY TO
TRIPODS AND RODS. Robert Bosch Tool Corporation
(“Seller”) warrants tripods and leveling rods for a pe­riod of one (1) year from date of purchase.

THIS LIMITED WARRANTY DOES NOT APPLY TO OTH­ER ACCESSORY ITEMS AND RELATED ITEMS. THESE
ITEMS RECEIVE A 90 DAY LIMITED WARRANTY.

To make a claim under this Limited Warranty, you must
return the complete product, transportation prepaid.
For details to make a claim under this Limited Warranty

ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURA­TION TO ONE YEAR FROM DATE OF PURCHASE. SOME
STATES IN THE U.S., AND SOME CANADIAN PROVINCES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IM­PLIED WARRANTY LASTS, SO THE ABOVE LIMITATION
MAY NOT APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY IN­CIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUD­ING BUT NOT LIMITED TO LIABILITY FOR LOSS OF
PROFITS) ARISING FROM THE SALE OR USE OF THIS
PRODUCT. SOME STATES IN THE U.S., AND SOME CA­NADIAN PROVINCES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE IN THE U.S.,
OR PROVINCE TO PROVINCE IN CANADA AND FROM
COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PROD­UCTS SOLD WITHIN THE UNITED STATES OF AMERI­CA, CANADA AND THE COMMONWEALTH OF PUERTO
RICO. FOR WARRANTY COVERAGE WITHIN OTHER
COUNTRIES, CONTACT YOUR LOCAL BOSCH DEALER
OR IMPORTER.

-28-

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com