Page 1
D7044
Installation Instructions
EN
Multiplex Single Input
Module
Page 2
D7044 | Installation Instructions |
Notices
Notices
These instructions cover the installation of the D7044
Multiplex Single Input Module in a fire system,
supervised by a D7024 or DS9400M Fire Alarm
Control Panel (FACP) with firmware revision 2.0 or
greater and a D7039 or DS9431 Multiplex Expansion
Module.
Install, test, and maintain the D7044 according to these
instructions, NFPA 72, Local Codes, and the Authority
Having Jurisdiction (AHJ).
Follow the procedures in these instructions
to avoid personal injury and damage to the
equipment. Failure to follow the procedures
can result in the D7044 not operating
properly. Bosch is not responsible for
improperly installed, tested, or maintained
devices.
Test the FACP according to NFPA 72.
1.0 Description
The D7044 (Figure 1) is a general purpose device that
connects a contact device to the FACP multiplex bus
with a supervised input loop.
Figure 1: D7044 Features
1
2
0
2
0
A
1
9
2
8
0
7
6
1
B
5
0
1
4
1
9
2
8
3
2
7
3
6
4
5
3
4
1 - Status LED
2 - Zone input terminals
3 - Mux bus loop terminals
4 - Rotary address switches
All operating power for the D7044 is drawn from the
FACP.
Rotary switches provide convenient address setting.
An on-board Status LED, visible through the faceplate,
indicates normal operation and communication with the
control panel. The LED flash rates are:
• Fast: Approximately 4 sec indicating an alarm
condition.
• Medium: Approximately 8 sec indicating normal
operation.
• Slow: Approximately 16 sec indicating a trouble
condition.
The D7044 can be mounted in a standard double-gang
or a 4 in. x 4 in. electrical box.
Bosch | 10/04 | 48337D2
Page 3
D7044 | Installation Instructions | 2.0 Setting the Address
2.0 Setting the Address
Set the D7044 address using a flat-bladed screwdriver to
position each rotary switch located on the front of the
module (Figure 2). Note that the switches click when
turned.
Figure 2: D7044 Address Setting
A
0
1
2
0
1
B
2
1
1 - Hundreds 2 - Tens 3 - Ones
A = D7024 FACP, B = DS9400M FACP
For example:
0 hundreds, 9 tens, 5 ones = Address 095 on the
The valid D7044 address range is 9 to 255. Refer to the
D7024 Operation and Installation Guide (P/N: 31499) or
the DS9400M Reference Guide (P/N: 44578) for
additional address limitations.
The A address range works on the D7039
Multiplex Expansion Module with the D7024
FACP. The B address range works on the
DS9431 Multiplex Expansion Module with
the DS9400M FACP.
0
1
9
8
7
2
3
4
6
5
2
D7024 FACP
0
1
9
8
7
2
3
4
6
5
3
Figure 3: Field Wiring Connections
1
2
3
1 - 2.21 kΩ end-of-line (EOL) resistor UL Listed
(P/N: 25899)
2 - Zone in (+)
3 - Zone in (-)
Note: The maximum zone wire resistance = 100 Ω.
Figure 4: Loop and Panel Wiring Connections
A
0
1
2
0
1
2
B
Figure 2 shows the A address range set at 095, allowing
the D7039 to work with the D7024 FACP.
3.0 Wiring
Ensure all power is removed before making
electrical connections. Failure to do so can
result in personal injury and damage to the
equipment.
Connections are made using the terminals on either side
of the D7044 (Items 2 and 3 in Figure 1 on page 2). All
terminals can accommodate up to and including
12 AWG (2.3 mm) wire. Follow the wiring guidelines as
specified by NFPA-70 and the local AHJ.
All wiring is power limited and supervised. Refer to
Figures 3 and 4 for the two types of wiring connections.
Use normally-open (NO) contacts for
Underwriters Laboratories, Inc. (UL) Listed
fire installations.
1
3
2
1
4
0
1
9
8
2
7
3
6
4
5
2
1 - Mux bus loop (+)
2 - Mux bus loop (-)
3 - To next device
4 - From previous device, the D7039, or the DS9431
3Bosch | 10/04 | 48337D
Page 4
D7044 | Installation Instructions |
4.0 Installation
4.0 Installation
Complete all wiring before mounting the D7044 and faceplate.
1. Wire the D7044 according to Figures 3 and 4 on page 3.
2. Mount the D7044 on a standard double-gang box (Figure 5) or 4 in. x 4 in. electrical box (Figure 6).
Figure 5: Mounting the D7044 on a Double- Gang Box
1
2
3
1
0
0
A
0
1
1
2
1
9
1
9
2
8
2
8
2
0
3
3
7
7
46
46
B
5
5
1 - Supplied mounting screws (4) 2 - D7044 Module 3 - Double-gang box
Figure 6: Mounting the D7044 on an Electrical Box
1
2
3
1
0
A
0
1
1
2
0
1
9
1
9
2
2
8
2
8
0
7
3
7
3
6
4
6
4
B
5
5
1 - Supplied mounting screws (2) 2 - D7044 Module 3 - 4 in. x 4 in. electrical box
Bosch | 10/04 | 48337D4
Page 5
3. Secure the faceplate to the front of the D7044 (Figure 7).
Figure 7: Mounting the Faceplate
2
1
D7044
D7044 | Installation Instructions | 4.0 Installation
3
0
0
A
1
2
0
1
2
B
0
1
9
8
7
6
1
9
2
2
8
3
7
3
4
6
4
5
5
1 - Supplied mounting screws (2) 2 - Faceplate 3 - D7044 Module on electrical box
5Bosch | 10/04 | 48337D
Page 6
D7044 | Installation Instructions |
5.0 Specifications
Table 1: Specifications
Control Panel
Programming Type
Control Panel
Requirements
Multiplex Bus Average
Current Draw
Operating Temperature
Relative Humidity
Listings and Approvals
Single input
D7024 FACP with ROM version 2.0 or greater and a D7039 Multiplex Expansion Module
installed. Refer to the D7024 Operation and Installation Guide (P/N: 31499) or the DS9400M
Reference Guide (P/N: 44578) for specific programming information. Refer to the D7039
Installation Instructions (P/N: 38685) or the DS9431 Installation Instructions (P/N: 41381) for
multiplex wiring information.
Alarm: 550 µA
Standby: 550 µA
Nominal: 12 V
+32°F to +120°F (0°C to +49°C)
Maximum of 93%, non-condensing
UL 864
California State Fire Marshall (CSFM)
5.0 Specifications
Bosch | 10/04 | 48337D6
Page 7
Notes
D7044 | Installation Instructions | Notes
7Bosch | 10/04 | 48337D
Page 8
Bosch
130 Perinton Parkway
Fairport, NY 14450-9199 USA
Customer Service: (800) 289-0096
Technical Support: (888) 886-6189
© 2004 Bosch
48337D
Loading...