Bosch B426-M Installation Manual

1 | Overview

The Ethernet Communication Module (wired to a compatible control

panel) is a four-wire powered SDI, SDI2, or option bus device that provides two-way communication with compatible control panels over

IPv4 or IPv6 Ethernet networks.

Figure 1.1: Board overview

Callout ― Description

1 ― Ethernet RJ-45 port

2 ― Yellow LINK LED

3 ― Green 100MB LED

4 ― Address switch

5 ― Heartbeat LED (blue)

6 ― TX and RX LEDs

7 ― Terminal strip

(to control panel or additional modules)

8 ― Interconnect wiring connectors

(to control panel or additional modules)

9 ― Tamper switch connector

2 | Bus address settings

One address switch determines the address for the module. The

control panel uses the address for communications. Use a slotted screwdriver to set the address switch.

NOTICE!

The module reads the address switch setting only during

power up. If you change the switch after you apply power to the module, you must cycle the power to the module in order for the new setting to be enabled.

Set the address switch per the Table 2.1. If multiple modules reside on the same system, each module must have a unique address. Figure 2.1

shows the address switch setting for SDI2 bus address 1.

Figure 2.1: Address switch

Control

panels

B9512G/

B8512G, B6512/B5512/ B4512/B3512, GV4, Solution 2000/3000

B9512G/

B8512G, GV4, Solution, 2000/3000

GV4,GV3,

GV2, D9412G/

D7412G/ D7212G v6.3 or higher

GV4 and GV3 5 92

FPD-7024

v1.06+,

DS7240V2, DS7220V2,

Easy Series, V3+, CMS

Series, AMAX Series

DS7400Xi 7 13

DS7400Xi 8 14 Reporting

FPD-7024, CMS Series, AMAX Series

Table 2.1: Address switch settings

Switch

position

1 1 SDI2 Automation,

2 2

3 80 SDI Automation

4 88 Remote

6 134 Option

9 250 Remote

Control

panel

address

Bus type Function

Remote Programming, or Reporting

programming or Reporting

3 | Installation

After you set the address switch for the proper address, install the module in the enclosure, and then wire it to the control panel and other devices.

Caution!

Remove all power (AC and battery) before making any connections. Failure to do so might result in personal injury and/or equipment damage.

3.1 | Mount the module in the enclosure

Mount the module into the enclosure’s 3-hole mounting pattern using the supplied mounting screws and mounting bracket. Refer to Figure 3.1.

Figure 3.1: Mounting the module in the enclosure

Callout ― Description

1 ― Module with mounting bracket installed

2 ― Enclosure

3 ― Mounting screws (3)

3.2 | Mount and wire the tamper switch

For instructions on this optional switch (on GV4 Series and B Series v2.xx control panels), refer to the Module (B426) Installation and Operation Guide (P/N: F01U266226) and the F01U003734).

EZTS Cover and Wall Tamper Switch Installation Guide (P/N:

Conettix Ethernet Communication

3.3 | Wire to the control panel

When you wire a B426/B426-M to an SDI or SDI2 control panel, you can use either the module’s terminal strip labeled R, Y, G, B (PWR, A, B, COM) or the module’s interconnect wiring connectors (wire included). Figure 1.1 indicates the location of both the terminal strip and the interconnect connectors on the module. Run the wires from the module to the data bus terminals on the compatible control panel.

NOTICE!

Use either the terminal strip wiring or interconnect wiring connector to the control panel. Do not use both. When connecting multiple modules, you can combine terminal strip and interconnect wiring connectors in series.

Figure 3.2: Wiring to the control panel (GV4 Series and FPD-7024 control panel shown)

Callout ― Description

1 ― SDI2 control panel. For SDI control panels, wire R, Y, G, B to

the SDI bus.

2 ― Interconnect wiring connectors

3 ― To Ethernet network

4 ― Terminal strip wiring

5 ― Interconnect cable (P/N: F01U079745) (included)

6 ― Option bus control panel

4 | Conguration

Congure the B426/B426-M using one of the methods described in this

section for your control panel type.

4.1 | PnP for SDI2 or option bus control panel

NOTICE!

Option bus control panels support AMAX 2100/ 3000/ 4000

rmware version v1.5 or higher only.

NOTICE!

By default, when connecting a eld replacement B426/

B426-M to an existing SDI2 or option bus control panel, the

panel overrides the module settings. To keep custom module settings when you connect a module to a congured control

panel, you must disable Panel Programming using web-based

conguration, prior to connecting to the SDI2 or option

bus.

When connected to a non-default SDI2 or option bus control panel, the

control panel automatically congures a connected module.

1. Set the address switch to the correct address for the control panel (SDI2 control panels use address 1 or 2, option control panels use addresses 134 or 250).

2. Connect the module to the control panel bus and apply power.

3. Program the control panel communication settings using RPS for SDI2 control panel, A-Link for option control panel, or the keypad.

4.2 | PnP for SDI or option bus control panels

When installing under the following conditions, the B426/B426-M needs

no further conguration:

– DHCP is available on your network. – AES encryption is not required. – Default B426/B426-M port settings (UDP on Port 7700) are

permitted by the network administrator.

4.3 | Web-based conguration

For installations requiring non-default conguration, use the B426/ B426-M web-based conguration pages.

To use the B426/B426-M conguration pages, you need the module’s IP

address or hostname.

– The default hostname for the module is the letter B followed

by the last six alpha-numeric digits of its MAC address (for example, B3F603F).

– Locate the IP address in the table on the DHCP server

(networked modules).

– To use Auto IP, directly connect from your PC to the module.

Within 60 seconds, the module temporarily assumes address

169.254.1.1 for conguration. (

Communication Module Installation and Operation Guide more information on using these methods).

NOTICE!

Before proceeding, ensure that the web browser is not

congured to use a proxy server. Refer to the browser’s

online help for instructions on disabling proxy service.

Logging into web-based conguration (B426 Conguration Pages):

1. Open an internet browser (Microsoft Internet Explorer or Mozilla Firefox) and type in the module’s IP address. The B426’s login page

opens.

2. Enter the password and click Login. The Device Information home page opens.

• For B426 (FW v3.09+) and B426-M (FW v3.10+) use the unique

passcode printed on the product label.

• For earlier versions of B426/B426-M, use the default passcode B42V2.

3. Browse to the desired settings page and congure the parameters.

4. Click OK and then click Save & Execute to save and apply all changes to the device.

NOTICE!

Before browsing to a new settings page, you must click OK to save edited values.

Refer to the Conettix Ethernet

for

5 | LED descriptions

6 | Certications

The module includes the following on-board LEDs to assist with

troubleshooting issues.

Flash pattern Function

Flashes once every 1 sec

3 quick ashes

every 1 sec

On Steady Trouble state. Indicates a trouble condition

Off LED trouble state. Module is not powered, or

Table 5.1: Heartbeat LED descriptions

Normal state: Indicates normal operation state.

Communication error state: Indicates a bus

communication error. The module is not

receiving commands from the control panel.

exists.

some other trouble condition prohibits the

module from controlling the heartbeat LED.

Flash pattern Function

RX (Receive)

ashes

TX (Transmit) ashes

Table 5.2: RX and TX LEDs descriptions

LINK (yellow)

ash pattern

Off Off No Ethernet link

On Steady Off 10 BASE-T link

Flash Off 10 BASE-T activity

On Steady On Steady 100 BASE-T link

Flash On Steady 100 BASE-T activity

Table 5.3: Ethernet LINK and 100mb LEDs descriptions

Condition Heartbeat Transmit

Network cable disconnected

6 | Show the rmware version

Obtaining an IP address

Low bus voltage

Occurs when the module receives a message

over the network connection – UPD, TCP, or

DNS.

Occurs when the module sends a message

over the network connection – UPD, TCP, or

DNS.

100mb (green)

Function

ash pattern

Receive

(TX)

On Steady Off 1 quick ash,

On Steady Off 2 quick ashes,

On Steady Off 3 quick ashes,

(RX)

repeating

Region CTN Certication

USA B426 UL 365 – Police Station Connected Burglar Alarm Units and Systems

UL 609 – Local Burglar Alarm Units and Systems

UL 864 – Control Units and Accessories for Fire Alarm Systems (Including NFPA 72)

UL 985 – Household Fire Warning System Units

UL 1023 – Household Burglar Alarm System Units

UL 1076 – Proprietary Burglar Alarm Units and Systems

UL 1610 – Central Station Burglar Alarm Units

FCC Part 15 Class B, NIST FIPS-197 AES Certication

(IP Communications)

Canada B426 CAN/ULC S303 – Local Burglar Alarm Units and Systems

CAN/ULC S304 – Signal Receiving Centre and Premise Alarm Control Units

CAN/ULC S559 – Fire Signal Receiving Centres and Systems

ULC-ORD C1023 – Household Burglar Alarm System Units

ULC-ORD C1076 – Proprietary Burglar Alarm Units and Systems

ICES-003 – Digital Apparatus

Australia

Belgium

B426/B426-M

EN 50130-4, EN 61000-6-3, EN 60950, EN 50131-10, EN 50136-2, EN 50130-5 Environmental Class II

C-Tick/RCM

INCERT B-509-0065

B426/B426-M

7 | Specications

Dimensions 59.5 mm x 108 mm x 16 mm (2.19 in x 4.25 in x 0.629 in)

Voltage (operating) 12 VDC nominal

Current (maximum) 100 mA max

Connectors LAN/WAN: RJ-45 modular port (Ethernet)

Ethernet cable Category 5 or better unshielded twisted pair, 100 m (328 ft) max length

Interface IEEE 802.3

Data bus wire size 1.02 mm to 0.65 mm (18 AWG to 22 AWG)

Data bus wire length Maximum distance - Wire size: 150 m (500 ft) - 0.65 mm (22 AWG), 300 m (1000 ft) - 1.02 mm (18 AWG)

Web browser Microsoft Internet Explorer; Mozilla Firefox

Compatibility B426:

AMAX 2000/2100/3000/4000

B9512G/B9512G-E, B8512G/B8512G-E B6512, B5512/B5512E, B4512/B4512E, B3512/B3512E D9412GV4/D7412GV4/D7212GV4 D9412GV3/D7412GV3/D7212GV3 D9412GV2/D7412GV2/7212GV2 Version 7.06 or higher

DS7220 Version 2.10 or higher DS7240 Version 2.10 or higher DS7400XiV4 Version 4.10 or higher

Easy Series V3+

FPD-7024 Version 1.02 or higher Solution 2000/3000

The module reporting timing category of transmission path is dependent on the associated control panel. The maximum timing category for

this device is SP4. Refer to the control panel’s dcoumentation for timing parameter values.

14 | Certications

B426-M: *AMAX 2000/2100/3000/4000 *Solution 2000/3000

* The B426-M is compatible with AMAX and Solution

control panels only.

Conettix Ethernet Communication Module

B426/B426-M

en Quick Start Guide

For complete installation, con guration, and testing instructions,

refer to the Conettix Ethernet Communication Module (B426) Installation and Operation Guide provided on the supplied

CD-ROM.

Bosch Security Systems B.V.

Torenallee 49 5617 BA Eindhoven Netherlands

www.boschsecurity.com

Internal failure On Steady On Steady On Steady

Table 5.4: Trouble conditions indicated through LEDs

Trademarks

All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.

Bosch Security Systems B.V. product manufacturing dates

Use the serial number located on the product label and refer to the Bosch Security Systems B.V. website at http://www.boschsecurity.com/datecodes/.