Business WLAN .11ac Access Point
bintec W2003ac-ext
•802.11ac/agbn 2x2 Mimo technology with up to 867 Mbit/s
•Dual concurrent operation at 5GHz and 2,4 GHz
•Enhanced feature set for performance optimizing
•Managed operation or stand-alone operation
•2 x Gigabit Ethernet with standard PoE (12,4W)
•Certified for operation in medical environments
•External antennas with RSMA connector
bintec W2003ac-ext
Business WLAN .11ac Access Point
Budget 802.11ac Access Point with full performance support of .11ac devices, interoperable to
.11n devices
Product Description
The bintec W2003ac-ext access point supports the new 802.11ac wireless standard. The dual radios allow for simultaneous operation in both the 2.4 GHz and 5 GHz frequency bands. bintec Client Management ensures that the wireless client is always able to operate at maximum speed. bintec Client Management offers a wide range of features and also ensures that the client is always connected to the access point that can provide the best performance.
MIMO 2x2 technology and the 802.11ac wireless standard allow for PHY data rates of up to 867 Mbps. The MIMO 2x2 technology with two transmission streams offers the considerable advantage of requiring less than 12.4 watts of power, enabling operation on a standard low-cost PoE infrastructure.
In addition, the MIMO 2x2 technology is an ideal match for current smartphones and tablet PCs, which frequently only support 802.11ac with MIMO 1x1. Access points with the expensive MIMO 3x3 or MIMO 4x4 technology are not able to realize their full performance potential with these types of terminal devices, which makes an access point operating on the 802.11 ac standard and MIMO 2x2 the better solution and the better value.
The bintec W2003ac-ext has external antennas for more flexibility. The included wall and ceiling mounting bracket makes installation easy.
The access point be managed using the bintec Cloud NetManager or a locally installed bintec WLAN Controller. Using the included free WLAN Controller license, you can operate this model as a master-AP to manage a small wireless LAN with up to six access points. Of course you can also configure the W2003ac-ext to run as a stand-alone AP. It's hard to imagine greater flexibility.
Variants
bintec elmeg GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany |
bintec W2003ac-ext |
Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25 |
31.05.2016 |
E-Mail: info@bintec-elmeg.com - www.bintec-elmeg.com |
Subject to technical alterations |
|
Page 2 / 8 |
|
|
|
|
bintec W2003ac-ext (5510000396)
WLAN Access Point with a dual concurrent radio module acc. 802.11ac/abgn (2.4/5 GHz) Mimo 2x2, 2 Gigabit ETH, PoE, 4 external antennas, incl. wall/ceiling mounting, incl. WLAN Controller license for Master AP, shipment without 100-240V wall adapter
Features
Wireless LAN (Radio 2)
Receiver Sensitivity @ 2.4 GHz |
MSC0/8 -93 dBm; MSC1/9 -92 dBm; MCS2/10 -89 dBm; MCS3/11 -86 dBm; MCS4/12 -83 dBm; |
802.11n 40 MHz |
MSC5/13 -81 dBm; MCS6/14 -78 dBm; MCS7/15 -76 dBm |
|
|
Output power limitation ( |
Adjustable in following steps: 5, 8,11,14,16 dBm and maximum. Maximal power varies depending |
without antenna gain) |
on data rate, frequency band and country setting. |
|
|
Output power @ 2.4 GHz |
Max. 20dBm (100mW EiRP) |
|
|
Output power @ 5 GHz |
Max. 23 dBm (200mW EiRP) |
|
|
Automatic Rate Selection (ARS) |
Available |
|
|
Transmission rate |
Automatic |
|
|
Number of spatial streams |
1 or 2 |
(802.11n) |
|
|
|
Bandwidth (802.11n) |
20/40 MHz (bundling of two adjoining 20 MHz channels to one 40 MHz channel) |
|
|
Short guard interval (802.11n) |
On/off switchable; increase of throughput by reduction of the guard intervals from 800ns to 400ns |
|
|
DTIM Period |
Adjustable |
|
|
Extended Performance Feature |
Beamforming, MRC (Maximum Ratio Combining), Block-Acknowlegde |
|
|
Multi SSID |
Up to 16 service sets per radio module, with virtual access points and own MAC address per SSID. |
|
|
Broadcast SSID |
On/off switchable |
|
|
RTS/CTS |
RTS/CTS threshold adjustable |
|
|
Operation Modes
WLAN operation mode WLAN = off / WLAN = Access Point (stand-alone/Managed/Master-AP/Cloud Managed)
Wireless LAN (Radio 1/2)
WLAN Standards |
802.11b; 802.11g; 802.11n Mimo 2x2 2.4 GHz 802.11ac/an; Mimo 2x2; 20/40/80 MHz; 5 GHz |
|
|
Receiver Sensitivity @ 2.4 GHz |
1 Mbps -94 dBm; 2 Mbps -94 dBm; 5,5 Mbps -94 dBm; 11 Mbps -94 dBm; 6 Mbps -94 dBm; 9 Mbps |
802.11b/g |
-94 dBm; 12 Mbps -94 dBm; 18 Mbps -94 dBm; 24 Mbps -94 dBm; 36 Mbps -86 dBm; 48 Mbps -82 |
|
dBm; 54 Mbps -80 dBm |
|
|
Receiver Sensitivity @ 2.4 GHz |
MCS0/8 -94 dBm; MCS1/9 -94 dBm; MCS2/10 -92 dBm; MCS3/11 -88 dBm; MCS4/12 -84 dBm; |
802.11n 20 MHz |
MCS5/13 -81 dBm; MCS6/14 -78 dBm; MCS7/15 -77 dBm |
|
|
bintec elmeg GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany |
bintec W2003ac-ext |
Phone: +49 - 911 9673-0 - Telefax: +49 - 911 688 07 25 |
31.05.2016 |
E-Mail: info@bintec-elmeg.com - www.bintec-elmeg.com |
Subject to technical alterations |
|
Page 3 / 8 |
|
|
|
|
Loading...