WMB 51201 CSNY
Washing Machine
User’s Manual
Plně automatická
pračka
Uživatel Manuální
Automatická pračka
Používateľská príručka
Document Number
2820524290_EN / 24-09-14.(16:13)
WMB 51201 CS NY
This product was manufactured using the latest technology in environmentally friendly conditions.
1 Important instructions for safety and environment
This section contains safety instructions that will help protect from risk of personal injury
or property damage. Failure to follow these instructions shall void any warranty.
1.1 General safety
• This product can be used by children at and above 8 years old and by persons whose
physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage
of the product and the risks it brings out. Children must not play with the product.
Cleaning and maintenance works should not be performed by children unless they
are supervised by someone. Children of less than 3 years should be kept away unless
continuously supervised.
• Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath
the machine will cause electrical parts to overheat. This will cause problems with your
product.
• If the product has a failure, it should not be operated unless it is repaired by the
Authorized Service Agent. There is the risk of electric shock!
• This product is designed to resume operating in the event of powering on after a
power interruption. If you wish to cancel the programme, see "Cancelling the programme" section.
• Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect to
have the grounding installation made by a qualified electrician. Our company shall not
be liable for any damages that will arise when the product is used without grounding
in accordance with the local regulations.
• The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.
• Never open the loading door or remove the filter while there is still water in the drum.
Otherwise, risk of flooding and injury from hot water will occur.
• Do not force open the locked loading door. The loading door will be ready to open just
a few minutes after the washing cycle comes to an end. In case of forcing the loading
door to open, the door and the lock mechanism may get damaged.
• Unplug the product when not in use.
• Never wash the product by spreading or pouring water onto it! There is the risk of
electric shock!
• Never touch the plug with wet hands! Never unplug by pulling on the cable, always
pull out by grabbing the plug.
• Use detergents, softeners and supplements suitable for automatic washing machines
only.
• Follow the instructions on the textile tags and on the detergent package.
• The product must be unplugged during installation, maintenance, cleaning and repairing procedures.
• Always have the installation and repairing procedures carried out by the Authorized
Service Agent. Manufacturer shall not be held liable for damages that may arise from
procedures carried out by unauthorized persons.
• If the power cable is damaged, it must be replaced by the manufacturer, after sales
service or a similarly qualified person (preferably an electrician) or someone designa-
3 / EN
Washing Machine / User’s Manual
ted by the importer in order to avoid possible risks.
• Place the product on a rigid, flat and level surface.
• Do not place it on a long-pile rug or similar surfaces.
• Do not place the product on a high platform or near the edge on a cascaded surface.
• Do not place the product on the power cable.
• Never use sponge or scrub materials. These will damage the painted, chrome plated
and plastic surfaces.
1.2 Intended use
• This product has been designed for domestic use. It is not suitable for commercial
use and it must not be used out of its intended use.
• The product must only be used for washing and rinsing of laundry that are marked
accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage or transportation.
1.3 Children's safety
• Packaging materials are dangerous to children. Keep packaging materials in a safe
place away from reach of the children.
• Electrical products are dangerous for the children. Keep children away from the product when it is in use. Do not let them to tamper with the product. Use child lock to
prevent children from intervening with the product.
• Do not forget to close the loading door when leaving the room where the product is
located.
• Store all detergents and additives in a safe place away from the reach of the children
by closing the cover of the detergent container or sealing the detergent package.
While washing the laundry at high temperatures, the loading door glass
becomes hot. Therefore, keep especially the children away from the
loading door of the machine while the washing operation is in progress.
1.4 Package information
• Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging
materials together with the domestic or other wastes. Take them to the packaging
material collection points designated by the local authorities.
1.5 Disposing of the waste product
• This product has been manufactured with high quality parts and materials which can
be reused and are suitable for recycling. Therefore, do not dispose the product with
normal domestic waste at the end of its service life. Take it to a collection point for the
recycling of electrical and electronic equipment. Please consult your local authorities
to learn the nearest collection point. Help protect the environment and natural resources by recycling used products. For children's safety, cut the power cable and break
the locking mechanism of the loading door so that it will be non-functional before disposing of the product.
4 / EN
Washing Machine / User’s Manual
1.6 Compliance with WEEE Directive
This product complies with EU WEEE Directive (2012/19/EU). This product
bears a classification symbol for waste electrical and electronic equipment
(WEEE).
This product has been manufactured with high quality parts and materials
which can be reused and are suitable for recycling. Do not dispose of the
waste product with normal domestic and other wastes at the end of its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It
does not contain harmful and prohibited materials specified in the Directive.
2 Installation
collection centers.
Refer to the nearest Authorised Service Agent for installation
of the product. To make the product ready for use, review
the information in the user manual and make sure that the
electricity, tap water supply and water drainage systems are
appropriate before calling the Authorized Service Agent. If they
are not, call a qualified technician and plumber to have any
necessary arrangements carried out.
INFORMATIONS
C
Preparation of the location and electrical, tap water and waste
water installations at the place of installation is under customer’s
responsibility.
Make sure that the water inlet and discharge hoses as well as the
power cable are not folded, pinched or crushed while pushing the
product into its place after installation or cleaning procedures.
B WARNING
Installation and electrical connections of the product must be
carried out by the Authorized Service Agent. Manufacturer shall not
be held liable for damages that may arise from procedures carried
out by unauthorized persons.
A WARNING
Prior to installation, visually check if the product has any defects on
it. If so, do not have it installed. Damaged products cause risks for
your safety.
2.1 Appropriate installation location
• Place the machine on a rigid floor. Do not place it on a long
pile rug or similar surfaces.
• Total weight of the washing machine and the dryer -with
full load- when they are placed on top of each other
reaches to approx. 180 kilograms. Place the product on a
solid and flat floor that has sufficient load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where temperature may
fall below 0ºC.
• Place the product at least 1 cm away from the edges of
other furniture.
2.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.
2.3 Removing the transportation locks
A WARNING
Do not remove the transportation locks before taking out the
packaging reinforcement.
Remove the transportation safety bolts before operating the
washing machine! Otherwise, the product will be damaged.
Loosen all the bolts with a suitable spanner until they rotate
freely (C). Remove transportation safety bolts by turning them
gently. Attach the plastic covers supplied in the User Manual
bag into the holes on the rear panel. (P)
INFORMATIONS
C
Keep the transportation safety bolts in a safe place to reuse when
the washing machine needs to be moved again in the future.
Never move the product without the transportation safety bolts
properly fixed in place!
5 / EN
Washing Machine / User’s Manual
2.4 Connecting water supply
INFORMATIONS
C
The water supply pressure required to run the product is between
1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters
of water flowing from the fully open tap in one minute to have your
machine run smoothly. Attach a pressure reducing valve if water
pressure is higher.
If you are going to use the double water-inlet product as a single
(cold) water-inlet unit, you must install the supplied stopper to
the hot water valve before operating the product. (Applies for the
products supplied with a blind stopper group.)
If you want to use both water inlets of the product, connect the
hot water hose after removing the stopper and gasket group from
the hot water valve. (Applies for the products supplied with a blind
stopper group.)
A WARNING
Models with a single water inlet should not be connected to the
hot water tap. In such a case the laundry will get damaged or the
product will switch to protection mode and will not operate.
Do not use old or used water inlet hoses on the new product. It may
cause stains on your laundry.
Connect the special hoses supplied with the product to the
water inlets on the product. Red hose (left) (max. 90 ºC) is for
hot water inlet, blue hose (right) (max. 25 ºC) is for cold water
inlet.
A WARNING
Ensure that the cold and hot water connections are made correctly
when installing the product. Otherwise, your laundry will come out
hot at the end of the washing process and wear out.
100cm
40cm
• To prevent flowing of dirty water back into the machine and
to allow for easy discharge, do not immerse the hose end
into the dirty water or do not drive it in the drain more than
15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be
stepped on and the hose must not be pinched between the
drain and the machine.
• If the length of the hose is too short, use it by adding
an original extension hose. Length of the hose may not
be longer than 3.2 m. To avoid water leak failures, the
connection between the extension hose and the drain
hose of the product must be fitted well with an appropriate
clamp as not to come off and leak.
2.6 Adjusting the feet
A WARNING
In order to ensure that the product operates more silently and
vibration-free, it must stand level and balanced on its feet. Balance
the machine by adjusting the feet. Otherwise, the product may
move from its place and cause crushing and vibration problems.
Loosen the lock nuts on the feet by hand. Adjust the feet until
the product stands level and balanced. Tighten all lock nuts
again by hand.
Tighten all hose nuts by hand. Never use a wrench when
tightening the nuts. Open the taps completely after making the
hose connection to check for water leaks at the connection
points. If any leaks occur, turn off the tap and remove the nut.
Retighten the nut carefully after checking the seal. To prevent
water leakages and damages caused by them, keep the taps
closed when the machine is not in use.
2.5 Connecting to the drain
• The end of the drain hose must be directly connected to
the wastewater drain or to the washbasin.
A WARNING
Do not remove the transportation locks before taking out the
packaging reinforcement.
• The hose should be attached to a height of at least 40 cm,
and 100 cm at most.
• In case the hose is elevated after laying it on the floor level
or close to the ground (less than 40 cm above the ground),
water discharge becomes more difficult and the laundry
may come out excessively wet. Therefore, follow the
heights described in the figure.
6 / EN
A WARNING
Do not use any tools to loosen the lock nuts. Otherwise, they will
get damaged.
2.7 Electrical connection
Connect the product to a grounded outlet protected by a fuse
complying with the values in the "Technical specifications"
table. Our company shall not be liable for any damages that
will arise when the product is used without grounding in
accordance with the local regulations.
• Connection must comply with national regulations.
• Power cable plug must be within easy reach after
installation.
• The voltage and allowed fuse or breaker protection are
specified in the “Technical specifications” section. If the
current value of the fuse or breaker in the house is less
than 16 Amps, have a qualified electrician install a 16 Amp
fuse.
• The specified voltage must be equal to your mains voltage.
• Do not make connections via extension cables or multiplugs.
Washing Machine / User’s Manual
B WARNING
Damaged power cables must be replaced by the Authorized Service
Agents.
2.8 First use
Before starting to use the product, make sure that all
preparations are made in accordance with the instructions in
sections "Important safety instructions" and "Installation".
To prepare the product for washing laundry, perform first
operation in Cotton-90 programme. Before starting the
programme, put max. 100 g of powder anti-limescale into
the main wash detergent compartment (compartment nr. II).
If the anti-limescale is in tablet form, put only one tablet into
compartment nr. II. Dry the inside of the bellow with a clean
piece of cloth after the programme has come to an end.
INFORMATIONS
C
Use an anti-limescale suitable for the washing machines.
Some water might have remained in the product due to the quality
control processes in the production. It is not harmful for the product.
2.9 Disposing of packaging material
Packaging materials are dangerous to children. Keep
packaging materials in a safe place away from reach of the
children.
Packaging materials of the product are manufactured from
recyclable materials. Dispose of them properly and sort in
accordance with recycled waste instructions. Do not dispose
of them with normal domestic waste.
2.10 Transportation of the product
Unplug the product before transporting it. Remove water drain
and water supply connections. Drain the remaining water in
the product completely; see, "Draining remaining water and
cleaning the pump filter". Install transportation safety bolts in
the reverse order of removal procedure; see, "Removing the
transportation locks".
INFORMATIONS
C
Never move the product without the transportation safety bolts
properly fixed in place!
2.11 Disposing of the old product
Dispose of the old product in an environmentally friendly
manner.
Refer to your local dealer or solid waste collection centre in
your area to learn how to dispose of your product.
For children's safety, cut the power cable and break the
locking mechanism of the loading door so that it will be
nonfunctional before disposing of the product.
3 Preparation
3.1 Things to be done for energy saving
Following information will help you use the product in an
ecological and energy-efficient manner.
• Operate the product in the highest capacity allowed by the
programme you have selected, but do not overload; see,
"Programme and consumption table".
• Always follow the instructions on the detergent packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities of lightly soiled
laundry.
• Do not use high temperatures for laundry that is not heavily
soiled or stained.
• Do not use detergent in excess of the amount
recommended on the detergent package.
3.2 Sorting the laundry
• Sort laundry according to type of fabric, colour, and degree
of soiling and allowable water temperature.
• Always obey the instructions given on the garment tags.
3.3 Preparing laundry for washing
• Laundry items with metal attachments such as, underwired
bras, belt buckles or metal buttons will damage the
machine. Remove the metal pieces or wash the clothes by
putting them in a laundry bag or pillow case.
• Take out all substances in the pockets such as coins, pens
and paper clips, and turn pockets inside out and brush.
Such objects may damage the product or cause noise
problem.
• Put small size clothes such as infant's socks and nylon
stockings in a laundry bag or pillow case.
• Place curtains in without compressing them. Remove
curtain attachment items.
• Fasten zippers, sew loose buttons and mend rips and
tears.
• Wash “machine washable” or “hand washable” labeled
products only with an appropriate programme.
• Do not wash colours and whites together. New, dark
coloured cottons release a lot of dye. Wash them
separately.
• Tough stains must be treated properly before washing. If
unsure, check with a dry cleaner.
• Use only dyes/colour changers and limescale removers
suitable for machine wash. Always follow the instructions
on the package.
• Wash trousers and delicate laundry turned inside out.
• Keep laundry items made of Angora wool in the freezer for
a few hours before washing. This will reduce pilling.
• Laundry that are subjected to materials such as flour, lime
dust, milk powder, etc. intensely must be shaken off before
placing into the machine. Such dusts and powders on the
laundry may build up on the inner parts of the machine in
time and can cause damage.
3.4 Correct load capacity
The maximum load capacity depends on the type of laundry,
the degree of soiling and the washing programme desired.
The machine automatically adjusts the amount of water
according to the weight of the loaded laundry.
A WARNING
Follow the information in the “Programme and consumption table”.
When overloaded, machine’s washing performance will drop.
Moreover, noise and vibration problems may occur.
7 / EN
Washing Machine / User’s Manual
Laundry types and their average weights in the following table
are given as examples.
Laundry type Weight (g)
Bathrobe 1200
Duvet cover 700
Bed Sheet 500
Pillowcase 200
Tablecloth 250
Towel 200
Men’s shirt 200
3.5 Loading the laundry
Open the loading door. Place laundry items loosely into the
machine. Push the loading door to close until you hear a
locking sound. Ensure that no items are caught in the door.
INFORMATIONS
C
The loading door is locked while a programme is running. The door
can only be opened a while after the programme comes to an end.
A WARNING
In case of misplacing the laundry, noise and vibration problems may
occur in the machine.
3.6 Using detergent and softener
Detergent Drawer
The detergent drawer is composed of three compartments:
- (1) for prewash
- (2) for main wash
– (3) for softener
– (*) in addition, there is siphon piece in the softener
compartment.
3
2
Detergent, softener and other cleaning agents
• Add detergent and softener before starting the washing
programme.
• Never open the detergent drawer while the washing
programme is running!
• When using a programme without prewash, do not put any
detergent into the prewash compartment (compartment nr.
1).
• In a programme with prewash, do not put liquid detergent
into the prewash compartment (compartment nr. 1).
• Do not select a programme with prewash if you are using a
detergent bag or dispensing ball. Place the detergent bag
or the dispensing ball directly among the laundry in the
machine.
• If you are using liquid detergent, do not forget to place
the liquid detergent cup into the main wash compartment
(compartment nr. 2).
1
3.7 Choosing the detergent type
The type of detergent to be used depends on the type and
colour of the fabric.
• Use different detergents for coloured and white laundry.
• Wash your delicate clothes only with special detergents
(liquid detergent, wool shampoo, etc.) used solely for
delicate clothes.
• When washing dark coloured clothes and quilts, it is
recommended to use liquid detergent.
• Wash woolens with special detergent made specifically for
woolens.
A WARNING
Use only detergents manufactured specifically for automatic
washing machines.
Do not use soap powder.
3.8 Adjusting detergent amount
The amount of washing detergent to be used depends on the
amount of laundry, the degree of soiling and water hardness.
Read the manufacturer's instructions on the detergent
package carefully and follow the dosage values.
• Do not use amounts exceeding the dosage quantities
recommended on the detergent package to avoid problems
of excessive foam, poor rinsing, financial savings and
finally, environmental protection.
• Use lesser detergent for small amounts or lightly soiled
clothes.
• Use concentrated detergents in the recommended dosage.
3.9 Using softeners
Pour the softener into the softener compartment of the
detergent drawer.
• Use the dosages recommended on the package.
• Do not exceed the (>max<) level marking in the softener
compartment.
• If the softener has lost its fluidity, dilute it with water before
putting it in the detergent drawer.
Using bleaches
• Select a programme with prewash and add the bleaching
agent at the beginning of the prewash. Do not put
detergent in the prewash compartment.
• Do not use bleaching agent and detergent by mixing them.
• Use just a little amount (approx. 50 ml) of bleaching agent
and rinse the clothes very well as it causes skin irritation.
Do not pour the bleaching agent onto the clothes and do
not use it for coloured clothes.
• When using oxygen based bleaches, follow the instructions
on the package and select a programme that washes at a
lower temperature.
• Oxygen based bleaches can be used together with
detergents; however, if its thickness is not the same with
the detergent, put the detergent first into the compartment
nr. "II" in the detergent drawer and wait until the detergent
flows while the machine is taking in water. Add the
bleaching agent from the same compartment while the
machine is still taking in water.
Using limescale remover
• When required, use limescale removers manufactured
specifically for washing machines only.
• Always follow instructions on the package.
8 / EN
Washing Machine / User’s Manual
3.10 Tips for efficient washing
Light colours and whites Colours Dark colours
(Recommended temperature
range based on soiling level:
40-90ºC)
Clothes
(Recommended temperature
range based on soiling level:
cold-40ºC)
(Recommended
temperature range
based on soiling level:
cold-40ºC)
Delicates/
Woolens/Silks
(Recommended
temperature range
based on soiling level:
cold-30ºC)
Heavily Soiled
(difficult stains such
as grass, coffee,
fruits and blood.)
Normally Soiled
(For example, stains
Soiling Level
caused by body on
collars and cuffs)
Lightly Soiled
(No visible stains
exist.)
It may be necessary to pre-treat
the stains or perform prewash.
Powder and liquid detergents
recommended for whites can be
used at dosages recommended
for heavily soiled clothes. It is
recommended to use powder
detergents to clean clay and soil
stains and the stains that are
sensitive to bleaches.
Powder and liquid detergents
recommended for whites can be
used at dosages recommended
for normally soiled clothes.
Powder and liquid detergents
recommended for whites can be
used at dosages recommended
for lightly soiled clothes.
Powder and liquid
detergents recommended
for colours can be used at
dosages recommended for
heavily soiled clothes. It is
recommended to use powder
detergents to clean clay and
soil stains and the stains that
are sensitive to bleaches. Use
detergents without bleach.
Powder and liquid detergents
recommended for colours
can be used at dosages
recommended for normally
soiled clothes. Use detergents
without bleach.
Powder and liquid detergents
recommended for colours
can be used at dosages
recommended for lightly
soiled clothes. Use detergents
without bleach.
Liquid detergents
suitable for colours
and dark colours can
be used at dosages
recommended for
heavily soiled clothes.
Liquid detergents
suitable for colours
and dark colours can
be used at dosages
recommended for
normally soiled clothes.
Liquid detergents
suitable for colours
and dark colours can
be used at dosages
recommended for lightly
soiled clothes.
Prefer liquid detergents
produced for delicate
clothes. Woolen and
silk clothes must be
washed with special
woolen detergents.
Prefer liquid detergents
produced for delicate
clothes. Woolen and
silk clothes must be
washed with special
woolen detergents.
Prefer liquid detergents
produced for delicate
clothes. Woolen and
silk clothes must be
washed with special
woolen detergents.
9 / EN
Washing Machine / User’s Manual
4 Operating the product
4.1 Control panel
1
1 - Programme Selection knob
(Uppermost position On / Off)
2 - Door open indicator
3 - Programme Follow-up indicator
4 - Start / Pause button
5 - Spin Speed Adjustment button
4.2 Preparing the machine
Make sure that the hoses are connected tightly. Plug in your
machine. Turn the tap on completely. Place the laundry in the
machine. Add detergent and fabric softener.
Programme selection
Select the programme suitable for the type, quantity
and soiling degree of the laundry in accordance with the
"Programme and consumption table" and the temperature
table below. Select the desired programme with the
Programme Selection button.
90˚C
60˚C
40˚C30˚CCold
C
Use an anti-limesc Programmes are limited with the highest spin
speed appropriate for that particular type of fabric. ale suitable for
the washing machines.
When selecting a programme, always consider the type of fabric,
colour, degree of soiling and permissible water temperature.
For further programme details, see “Programme and consumption
table”.
Heavily soiled white cottons and linens. (coffee
table covers, tableclothes, towels, bed sheets,
etc.)
Normally soiled, coloured, fade proof linens,
cottons or synthetic clothes (shirt, nightgown,
pajamas, etc.) and lightly soiled white linens
(underwear, etc.)
Blended laundry including delicate textile (veil
curtains, etc.), synthetics and woolens.
INFORMATIONS
4.3 Main programmes
Depending on the type of fabric, use the following main
programmes.
• Bavlna (Cottons)
Use this programme for your cotton laundry (such as bed
sheets, duvet and pillowcase sets, towels, bathrobes,
underwear, etc.). Your laundry will be washed with vigorous
washing action for a longer washing cycle.
• Syntetika (Synthetics)
Use this programme to wash your synthetic clothes (shirts,
blouses, synthetic/cotton blends, etc.). It washes with a gentle
action and has a shorter washing cycle compared to the
Cotton programme.
For curtains and tulle, use the Synthetic 40˚C programme.
As their meshed texture causes excessive foaming, wash the
veils/tulle by putting little amount of detergent into the main
wash compartment. Do not put detergent in the prewash
compartment.
• Vlna 40 (Woollens)
Use this programme to wash your woolen clothes. Select
the appropriate temperature complying with the tags of your
clothes. Use appropriate detergents for woolens.
4.4 Additional programmes
For special cases, additional programmes are available in the
machine.
INFORMATIONS
C
Additional programmes may differ according to the model of the
machine.
• Bavlna Eco (Cotton Economic)
Use this programme to wash your laundry washable in
cottons programme for a longer time, still with a very good
performance for saving purposes.
INFORMATIONS
C
Cottons Eco programme consumes less energy compared to other
cottons programmes.
• Jemné 30° (Delicate)
Use this programme to wash your delicate clothes. It washes
with a gentle action without any interim spin compared to the
Synthetics programme.
• Rucní praní 20° (Hand wash)
Use this programme to wash your woolen/delicate clothes
that bear “not machine- washable” tags and for which hand
wash is recommended. It washes laundry with a very gentle
washing action to not to damage clothes.
2
3
4
5
10 / EN
Washing Machine / User’s Manual
• Mini 30
Use this programme to wash your lightly soiled cotton clothes
in a short time.
• Bavlna s Předpírkou (Prewash-Cottons)
Prefer this programme only for heavily soiled cotton clothes.
INFORMATIONS
C
Not using this programme with prewash will save energy, water,
detergent and time.
4.5 Special programmes
For specific applications, select any of the following
programmes.
• Máchání (Rinse)
Use this programme when you want to rinse or starch
separately.
• Odstřeďování + Vypouštění (Spin + Drain)
Use this programme to apply an additional spin cycle for your
laundry or to drain the water in the machine.
INFORMATIONS
C
If you wish to drain the water only without spinning your laundry,
select the Spin+Pump programme and press “Start / Pause”
button. Machine will switch to spin step once it completes the
program step. Press “Start / Pause” button to stop the machine as
soon as you see the drum rotating. And cancel this programme by
turning Programme Selection knob to any other position.
4.6 Spin speed selection
Whenever a new programme is selected, the recommended
spin speed of the selected program is displayed on the spin
speed indicator.
To decrease the spin speed, press the spin speed adjustment
button. Spin speed decreases gradually.
Then, depending on the model of the product, “Rinse Hold”
and “No Spin” options appear on the spin speed led indicator.
4.7 Rinse Hold
If you are not going to unload your clothes immediately after
the programme completes, you may use rinse hold function to
keep your laundry in the final rinsing water in order to prevent
them from getting wrinkled when there is no water in the
machine.
In rinse hold step, the machine will be in pause mode and
“start/pause” led will be blinking. In rinse hold step, if you
want to drain the water without spinning your laundry,
press the “start/pause” button. Programme will resume and
complete after draining the water.
If you want to spin the laundry held in water, select the
spin speed and press “start/pause button. The programme
resumes, water is drained, laundry is spun and the
programme is completed.
Indicative values for Synthetics programmes (EN)
Remaining Moisture
Content (%) **
Load (kg)
Water
Consumption
(l)
Energy
Consumption
(kWh)
Programme
Duration
Synthetics 60
Synthetics 40
* You can see the washing time of the programme you have selected on the display of the machine. It is normal that small
differences may occur between the time shown on the display and the real washing time.
** Remaining moisture content values may differ according to the selected spin speed.
2.5 55 1.02 01:53 45 40
2.5 54 0.50 01:45 45 40
≤ 1000 rpm > 1000 rpm
(min) *
11 / EN
Remaining Moisture
Content (%) **
Washing Machine / User’s Manual
4.8 Programme and consumption table
EN
Programme
Bavlna 90 5 130 53 1.63 1400
Bavlna s Předpírkou 60 5 115 64 1.10 1400
Bavlna 40 5 120 50 0.97 1400
Bavlna Cold 5 120 52 0.10 1400
Bavlna Eco 60** 5 145 45 0.80 1400
Bavlna Eco 60** 2.5 145 38 0.75 1400
Bavlna Eco 40** 2.5 116 38 0.65 1400
Syntetika 60 2.5 113 55 1.02 800
Syntetika 40 2.5 105 54 0.50 800
Syntetika Cold 2.5 66 52 0.10 800
Jemné 30° 30 2 61 47 0.26 800
Vlna 40 40 1.5 54 50 0.35 800
Rucní praní 20° 20 1 41 34 0.20 800
Mini 30 30 2.5 29 72 0.21 1400
2
Max. Load (kg)
Programme Duration (~min)
Water Consumption (l)
Energy Consumption (kWh)
Max. Speed***
• : Selectable
** : Energy Label programme (EN 60456 Ed.3)
***: If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed.
INFORMATIONS
C
Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature, ambient temperature, type
and amount of laundry, selection of auxiliary functions and spin speed, and changes in electric voltage.
** “Cotton Economic 40°C and Cotton Economic 60°C are standard cycles.” These cycles are known as ‘40°C
cotton standard cycle’ and ‘60°C cotton standard cycle’ and indicated with the symbols on the
panel.
12 / EN
Washing Machine / User’s Manual
4.9 Starting the programme
Press Start / Pause button to start the programme.
Programme follow-up light showing the startup of the
programme will turn on.
Progress of programme
Progress of a running programme can be followed from the
Programme Follow-up indicator with the lights "Running" and
"End/Cancel".
INFORMATIONS
C
If the machine does not pass to the spinning step, automatic
unbalanced load detection system might have been activated due to
the unbalanced distribution of the laundry in the machine.
4.10 Loading door lock
There is a locking system on the loading door of the machine
that prevents opening of the door in cases when the water
level is unsuitable.
If you want to open loading door when the machine is in use,
press "Start / Pause" button to pause the machine. "Door
Open" light will start flashing when the machine is switched
to Pause mode. Machine checks the level of the water inside.
If the level is suitable, "Door Open" light illuminates steadily
within 1-2 minutes and the loading door can be opened.
If the level is unsuitable, "Door Open" light turns off and the
loading door cannot be opened. If you are obliged to open
the loading door when the "Door Open" light is off, you
have to cancel the current programme; see "Cancelling the
programme".
Switching the machine to pause mode
Press the "Start / Pause" button to switch the machine to
pause mode while a programme is running. "Running" light
starts flashing on the Programme Follow-up indicator to show
that the machine has been switched to the pause mode.
When the loading door is ready to be opened, "Door Open"
light will illuminate continuously.
Adding or taking out laundry
Press "Start / Pause" button to switch the machine to pause
mode. When the machine is switched to pause mode,
"Running" light flashes. Wait until the Loading Door can be
opened. Open the Loading Door and add or take out the
laundry.
Close the Loading Door. Press "Start / Pause" button to start
the machine.
INFORMATIONS
C
The door can be opened if the water level is suitable. Door open
symbol flashes until the loading door gets ready to be opened. The
symbol’s light is steady when the door is ready to open. You can
open the door to add/take out laundry.
4.11 Cancelling the programme
To cancel the programme, turn the Programme Selection knob
to select another programme. Previous programme will be
cancelled. "End/Cancel" light will flash continuously to notify
that the programme has been cancelled.
INFORMATIONS
C
If you start a new programme after cancelling the previous one,
this new programme will start without draining the water in the
machine.
If you must certainly open the loading door when the “Door
Open” light is off, you need to use “Spin+Pump” programme. See
“Spin+Pump”
Re-spinning the laundry
Unbalanced load control system can prevent spinning
because of unbalanced load of laundry in the machine. If you
would like to spin again:
Rearrange the laundry in the machine. Select Spin+Pump
programme and press “Start / Pause" button.
4.12 End of programme
"End/Cancel" light on the programme follow-up indicator will
light up once the programme comes to an end; and "Door
Open" symbol flashes for 1-2 minutes until the door is ready
to open. When "Door Open" symbol is steadily illuminated, the
door can be opened.
To turn off the machine, turn program selection knob to "On
/ Off" position. Take out your laundry and close the loading
door. The machine will be ready for the next run.
4.13 Door Open
"Door Open" symbol is illuminated when the door is ready
to open. It flashes until the door gets ready to open. If the
"Door Open" symbol is not illuminated, do not force the door
to open. The symbol's light is steady when the door is ready
to open.
4.14 Your machine is equipped
with a “Standby Mode”
In case of not starting any programme or waiting without
making any other operation when the machine is turned on
by On/Off button and while it is in selection step or if no other
operation is performed approximately 2 minutes after the
programme you selected has come to an end, your machine
will automatically switch to energy saving mode. Brightness of
indicator lights will decrease. Also, if your product is equipped
with a display showing the programme duration, this display
will completely turn off. In case of rotating the Programme
Selection knob or pressing any button, lights and display
will restore to their previous condition. Your selections made
while exiting the energy saving mode may change. Check
the appropriateness of your selections before starting the
programme. Readjust if necessary. This is not a fault.
13 / EN
Washing Machine / User’s Manual
5 Maintenance and cleaning
Service life of the product extends and frequently faced
problems decrease if cleaned at regular intervals.
5.1 Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every
4-5 washing cycles) as shown below in order to prevent
accumulation of powder detergent in time.
Press the dotted point on the siphon in the softener
compartment and pull towards you until the compartment is
removed from the machine.
INFORMATIONS
C
If more than normal amount of water and softener mixture starts to
gather in the softener compartment, the siphon must be cleaned.
5.3 Cleaning the body and control panel
Wipe the body of the machine with soapy water or noncorrosive mild gel detergents as necessary, and dry with a
soft cloth.
Use only a soft and damp cloth to clean the control panel.
A WARNING
Never use sponge or scrub materials. These will damage the
painted and plastic surfaces.
5.4 Cleaning the water intake filters
There is a filter at the end of each water intake valve at the
rear of the machine and also at the end of each water intake
hose where they are connected to the tap. These filters
prevent foreign substances and dirt in the water to enter the
washing machine. Filters should be cleaned as they do get
dirty.
Wash the detergent drawer and the siphon with plenty of
lukewarm water in a washbasin. Wear protective gloves or use
an appropriate brush to avoid touching of the residues in the
drawer with your skin when cleaning. Insert the drawer back
into its place after cleaning and make sure that it is seated
well.
5.2 Cleaning the loading door and the drum
Residues of softener, detergent and dirt may accumulate in
your machine in time and may cause unpleasant odours and
washing complaints. To avoid this, use the Drum Cleaning
programme. If your machine does not have a Drum Cleaning
programme, use Cotton-90 programme. Before starting the
programme, put max. 100 g of powder anti-limescale into
the main wash detergent compartment (compartment nr. II).
If the anti-limescale is in tablet form, put only one tablet into
compartment nr. II. Dry the inside of the bellow with a clean
piece of cloth after the programme has come to an end.
INFORMATIONS
C
Repeat Drum Cleaning process in every 2 months.
Use an anti-limescale suitable for the washing machines.
After every washing make sure that no foreign substance is
left in the drum.
If the holes on the bellow shown in the figure is blocked, open
the holes using a toothpick.
INFORMATIONS
C
Foreign metal substances will cause rust stains in the drum.
Clean the stains on the drum surface by using cleaning agents for
stainless steel. Never use steel wool or wire wool.
Close the taps. Remove the nuts of the water intake hoses
to access the filters on the water intake valves. Clean them
with an appropriate brush. If the filters are too dirty, take them
out by means of pliers and clean them. Take out the filters
on the flat ends of the water intake hoses together with the
gaskets and clean thoroughly under running water. Replace
the gaskets and filters carefully in their places and tighten the
hose nuts by hand.
5.5 Draining remaining water and
cleaning the pump filter
The filter system in your machine prevents solid items such
as buttons, coins and fabric fibers clogging the pump impeller
during discharge of washing water. Thus, the water will be
discharged without any problem and the service life of the
pump will extend.
If the machine fails to drain water, the pump filter is clogged.
Filter must be cleaned whenever it is clogged or in every 3
months. Water must be drained off first to clean the pump
filter.
In addition, prior to transporting the machine (e.g., when
moving to another house) and in case of freezing of the water,
water may have to be drained completely.
A WARNING
Foreign substances left in the pump filter may damage your
machine or may cause noise problem.
In order to clean the dirty filter and discharge the water:
Unplug the machine to cut off the supply power.
A WARNING
Temperature of the water inside the machine may rise up to 90 ºC.
To avoid burning risk, filter must be cleaned after the water in the
machine cools down.
14 / EN
Washing Machine / User’s Manual
Open the filter cover by pulling it from both sides at the top.
INFORMATIONS
C
You can remove the filter cover by slightly pushing downwards with
a thin plastic tipped tool, through the gap above the filter cover. Do
not use metal tipped tools to remove the cover.
Follow the steps below to discharge the water.
Place a large container in front of the filter to catch water
from the filter. Loosen pump filter (anticlockwise) until water
starts to flow. Fill the flowing water into the container you
have placed in front of the filter. Always keep a piece of cloth
handy to absorb any spilled water. When the water inside the
machine is finished, take out the filter completely by turning it.
Clean any residues inside the filter as well as fibers, if any,
around the pump impeller region. Install the filter.
Seat the tabs in the lower part into their places first, and then
press the upper part to close.
15 / EN
Washing Machine / User’s Manual
6 Technical specifications
Complying Commission Delegated Regulation (EU) No 1061/2010
Supplier name or trademark BEKO
Model name WMB 51201 CS NY
Rated capacity (kg) 5
Energy efficiency class / Scale from A+++ (Highest Efficiency) to D (Lowest Efficiency) A+
Annual Energy Consumption (kWh)
Energy consumption of the standard 60°C cotton programme at full load (kWh) 0.800
Energy consumption of the standard 60°C cotton programme at partial load (kWh) 0.745
Energy consumption of the standard 40°C cotton programme at partial load (kWh) 0.650
Power consumption in ‘off-mode’ (W) 0.200
Power consumption in ‘left-on mode’ (W) 1.000
Annual Water Consumption (l)
Spin-drying efficiency class / Scale from A (Highest Efficiency) to G (Lowest Efficiency) B
Maximum spin speed (rpm) 1200
Remaining moisture Content (%) 53
Standard cotton programme
Programme time of the standard 60°C cotton programme at full load (min) 145
Programme time of the standard 60°C cotton programme at partial load (min) 145
Programme time of the standard 40°C cotton programme at partial load (min) 116
Duration of the left-on mode (min) N/A
Airborne acoustical noise emissions washing/spinning (dB) 61/77
Built-in No
Height (cm) 84
Width (cm) 60
Depth (cm) 41.5
Net weight (±4 kg.) 55
Single Water inlet / Double Water inlet
• Available
Electrical input (V/Hz) 230 V / 50Hz
Total current (A) 10
Total power (W) 1550
Main model code 9413
(1)
Energy Consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load, and the consumption
of the low-power modes. Actual energy consumption will depend on how the appliance is used.
(2)
Water consumption based on 220 standard washing cycles for cotton programmes at 60°C and 40°C at full and partial load. Actual water con-
sumption will depend on how the appliance is used.
(3)
“Standard 60°C cotton programme” and the “standard 40°C cotton programme” are the standard washing programmes to which the information in
the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient programmes in terms of combined energy and water consumption.
Technical specifications may be changed without prior notice to improve the quality of the product.
(1)
(2)
(3)
Cotton Eco 60°C and 40°C
168
9900
• / -
16 / EN
Washing Machine / User’s Manual
Loading...