Condenser
Sensor Dryer
DCU 6130W
DCU 6130S
DCU 6130B
Read this manual prior to initial operation of the product!
Dear Customer,
We hope that your product, which has been manufactured in modern facilities and passed through a strict quality control procedure, will give you very good results.
We advise you to read through this manual carefully before using your product and keep it for future reference.
This User Manual will
•Help you use your machine in a fast and safe way.
•Read the User Manual before installing and starting your product.
•In particular, follow the instructions related to safety.
•Keep this User Manual within easy reach for future reference.
•Please read all additional documents supplied with your product. Remember that this User Manual is also applicable for several other models.
Explanation of symbols
Throughout this User Manual the following symbols are used:
A Important safety information. Warning for hazardous situations with regard to life and property.
B
C
Caution; Warning for supply voltage.
Caution; Warning for fire hazard.
Caution; Warning for hot surfaces.
Read the instructions.
Useful information. Important information or useful hints about usage.
This appliance’s packaging material is recyclable. Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose. Your appliance also contains a great amount of recyclable material. It is marked with this label to indicate the used appliances that should not be mixed with other waste. This way, the appliance recycling organised by your manufacturer will be done under the best possible conditions, in compliance with European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment. Contact your town hall or your retailer for the used appliance collection points closest to your home. We thank you doing your part to protect the environment.
DCU6130WSB/080512.1652
TABLE OF CONTENTS |
|
1 Your Dryer |
4 |
Overview.............................................. |
4 |
Technical Specifications....................... |
5 |
2 Important safety information6 |
|
General safety...................................... |
6 |
Intended use........................................ |
7 |
Children’s safety................................... |
7 |
3 Installation |
8 |
Appropriate installation location............ |
8 |
Removing the transportation safety |
|
assembly.............................................. |
8 |
Under counter installation..................... |
8 |
Mounting over a washing machine....... |
8 |
Connection to water drain;................... |
8 |
Adjusting the feet................................. |
9 |
First use............................................... |
9 |
Disposing of packaging material........... |
9 |
Transportation of the machine.............. |
9 |
Disposing of the old machine............... |
9 |
4 Electrical Connection |
10 |
Attention!........................................... |
10 |
Electrical requirements....................... |
10 |
Fitting a different plug ........................ |
10 |
Washer/dryer combination................. |
10 |
5 Initial preparations for drying11
Things to be done for energy saving:..11 |
|
Laundry suitable for drying in the |
|
machine............................................. |
11 |
Laundry unsuitable for drying in the |
|
machine............................................. |
11 |
Preparing laundry for drying................ |
12 |
Correct load capacity......................... |
12 |
6 Selecting a Programme and |
|
OperatingYour Machine |
13 |
Control panel...................................... |
13 |
Preparing the machine....................... |
14 |
Programme selection......................... |
16 |
Programme selection and consumption |
|
table................................................... |
16 |
Auxiliary function................................ |
17 |
Warning indicators............................. |
17 |
Time delay......................................... |
17 |
Starting the programme..................... |
17 |
Progress of programme...................... |
17 |
Changing the programme after it has |
|
started............................................... |
17 |
Child-proof lock.................................. |
18 |
Finishing by cancelling the programme18. |
|
End of programme............................. |
19 |
7 Maintenance and cleaning |
20 |
Filter Cartridge / Door Inner Surface... |
20 |
Sensor .............................................. |
20 |
Water tank;........................................ |
20 |
For the condenser ............................. |
21 |
8 Suggested solutions for |
|
problems |
23 |
9 Guarantee |
24 |
What is covered?............................... |
24 |
What is not covered?......................... |
24 |
Important notes.................................. |
24 |
10 Service |
25 |
1
Your Dryer
Overview
7
1
6
5
2
4
3
1- Control panel |
5- Rating plate |
2- Kick plate opening tab |
6- Fluff filter |
3-Adjustable feet |
7- Power cord |
4-Kick plate |
|
4 EN
Technical Specifications
EN
Height (adjustable) |
84.6 cm |
|
|
Width |
59.5 cm |
|
|
Depth |
53 cm |
|
|
Capacity (max.) |
6 kg |
|
|
Weight (net) |
36 kg |
|
|
Voltage |
|
|
|
Rated power input |
See type label |
|
|
Model code |
|
|
|
Type label is located behind the loading door.
Specifications of this appliance may change without notice to improve the quality of the product. Figures in this manual are schematic and may not match your product exactly.
Values stated on the machine labels or in the documentation accompanying it are obtained in laboratory in accordance with the relevant standards. Depending on operational and environmental conditions of the appliance, values may vary.
5 EN
2 Important safety instructions
This section includes safety information that will help protection from risks of personal injuries or damages. Failure to follow these instructions
shall cause any warranty to become void.
General safety
•Never place the machine on a carpetcovered floor, otherwise, lack of airflow beneath the machine may cause electrical parts to overheat. This will cause problems with your machine.
•If the power cable or mains plug is damaged, you must call Authorised Service Agent for repair.
•The product should not be plugged in during installation, maintenance and repair works. Such works should always be made by the technical service. Manufacturer shall not be held responsible for damages arising from processes carried out by unauthorised persons.
•Connect the product to a grounded outlet protected by a fuse of suitable capacity as stated in the technical specifications table.
•Operate your product at temperatures between +5°C and +35°C.
•Do not use electrical devices in the product.
•Do not connect the air exit of the product to the exit ducts which are used for the exhaust fumes of the devices operating with gas or other types of fuel.
•You must provide enough ventilation in order to prevent gases exiting from devices operating with other types of fuels including the naked flame from accumulating in the room due to the back fire effect.
•Always clean the lint filter before or after each loading.
•Never operate your dryer without the lint filter installed.
•Do not allow fibre, dust and dirt accumulation around the exhaust exit and at adjacent areas.
•Power cable plug must be within easy reach after installation.
•Do not use extension cords, multi-plugs or adaptors to connect the dryer to power supply in order to decrease the risk of electric shock.
•Do not make any changes on the plug supplied with the product. If it is not compatible with the socket, have a qualified electrician change the socket with a suitable one.
•Items cleaned or washed with gasoil/ fuel oil, dry-laundry solvents and other combustible or explosive materials as well as the items that are contaminated or spotted with such materials should not be dried in the product since they emit flammable or explosive vapor.
•Do not dry items cleaned with industrial chemicals in the dryer.
•Do not dry unwashed items in the dryer.
•Items soiled with cooking oils, acetone, alcohol, fuel oil, kerosene, stain remover, turpentine, paraffin and paraffin removers must be washed in hot water with plenty of detergent before being dried in the dryer.
•Garments or pillows bolstered with rubber foam (latex foam), shower bonnets, water resistant textiles, materials with rubber reinforcement and rubber foam pads should not be dried in the dryer.
•Do not use fabric softeners and anti-static products unless they are recommended by the manufacturers of the fabric softener or the product.
•This product must be earthed. Grounding installation decreases the risk of electric shock by opening a path with low resistance for the electricity flow in case of a malfunction or failure. Power cable of this product is equipped with a conductor and a grounding plug that allows for grounding the product. This plug must be installed appropriately and inserted into a socket which is grounded in accordance with the local laws and regulations.
•Do not install the product behind a door with a lock, sliding door or a door that has a hinge against the hinge of the dryer.
•Do not install or leave this product in places where it will be exposed to outdoor conditions.
•Do not tamper with the controls.
•Do not perform any repair or part replacing
6 EN
procedures on the product even if you know or have the ability to perform unless it is clearly suggested in the operating instructions or the published service manual.
•Inside and exhaust duct of the product must be cleaned by the qualified service personnel periodically.
•Wrong connection of grounding conductor of the product can cause electric shock. If you have any suspect about the grounding connection, have it checked by a qualified electrician, service representative or service personnel.
•Do not reach into the machine when the drum is spinning.
•Unplug the machine when it is not in use.
•Never wash down the appliance with water! There is the risk of electric shock! Always disconnect by unplugging from the mains before cleaning.
•Never touch the plug with wet hands. Never unplug by pulling on the cable, always pull out by grabbing the plug only. Do not operate the machine if the power cable or plug is damaged!
•Never attempt to repair the machine yourself, otherwise, you will be putting your life and others’ lives in danger.
•For malfunctions that cannot be solved by following the information given in the safety instructions:
Turn off the machine and contact an authorised service agent.
•Do not stop the dryer before the drying cycle comes to an end unless you will remove all laundry from the dryer quickly in order to hang them and dissipate the heat.
•Remove the door of the drying compartment before decommissioning or disposing of the product.
•The final step of the drying cycle (cooldown cycle) occurs without applying heat to ensure that the items are left at a temperature that will not damage them.
•Fabric softeners or similar products should be used as specified by the fabric softener instructions.
•Underwear that contains metal reinforcements should not be placed in
a dryer. Damage to the dryer can result if metal reinforcements come loose during drying.
•Check all garments for forgotten lighters, coins, metal pieces, needles, etc. before loading.
•At times when your dryer is not in use or after the laundry is taken out following the completion of drying process, turn off by using the On/Off button. In cases when the On/Off button is on (while the dryer is energized), keep the door of the dryer
closed.
Intended use
•This product has been designed for domestic use. It should not be used for other purposes.
•Use the product only for drying laundry that are marked accordingly.
•Dry only those articles in your product that are stated in this manual.
•This product is not intended to be used by persons with physical, sensory or mental disorders or unlearned or inexperienced people (including children) unless they
are attended by a person who will be responsible for their safety or who will instruct them accordingly for use of the product.
Children’s safety
•Electrical appliances are dangerous for the children. Keep children away from the machine when it is operating. Do not let them tamper with the machine.
•Packaging materials are dangerous to children. Keep the packaging materials out of reach of children or dispose them by classifying according to waste directives.
•Do not allow children sit/climb on or enter in the product.
•Children should be supervised to ensure that they do not play with the product.
•Close the loading door when you leave the area where the product is located.
7 EN
3 Installation
A Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products will cause risks
for your safety.
Appropriate installation location
• Install the product in an environment which has no risk of freezing and is in a stable and level position.
• Operate your product in a well ventilated, dust-free environment.
• Do not block the air ducts in front of and under the product with materials such as long pile rugs and wooden plinths.
• Do not place your product on a long pile rug or on similar surfaces.
• Do not install the product behind a door with a lock, sliding door or a hinged door which can strike the product.
• Once the product is installed, it should stay at the same place where its connections have been made. When installing the product, make sure that the rear wall of it does not touch anywhere (tap, socket, etc.) and also pay attention to install the product at a place where it will stay permanently.
B Do not place the product on top of the power cable.
•Keep at least 1.5 cm distance to walls of other furniture.
Removing the transportation safety assembly
ARemove the transportation safety assembly before using the product for the first time.
1.Open the loading door.
2.There is a nylon bag inside the drum that contains a piece of styrofoam. Hold it from its section marked with XX.
3.Pull the nylon towards yourself and remove the transportation safety assembly.
AMake sure that you have removed the transportation safety assembly
(nylon+styrofoam pieces) before using the product for the first time. Do not leave any items inside the drum.
Under counter installation
•The product should never be operated without the top trim.
•Leave at least 3 cm of space between the side and rear walls of the product and the walls of the counter/cupboard when installing your product under a counter or in a cupboard.
Mounting over a washing machine
•A fitting device should be used between the two machines when installing above a washing machine. The bracket must be installed by the Authorised Service Agent.
•Place the product on a firm floor. If it will be placed on top of a washing machine, the approximate weight of both machines may reach 180 kg when they are full. Therefore, the floor must be capable of carrying the load on it!
Connection to water drain;
In products equipped with a condenser unit the water accumulated during the drying cycle is collected in the water tank. You should drain the accumulated water after each drying cycle.
You can directly send the accumulated water out through the water drain hose supplied with the machine instead of periodically draining the
8 EN
water collected in the water tank. Connecting the water drain hose;
1.Remove the hose on the machine by pulling it out from its end. Do not use any tools to take out the hose.
2.Connect the special drain hose supplied with the machine to the pipe fitting.
3.The other end of the drain hose can be directly connected to the wastewater drain or to the washbasin. The fitting must always be secured in all types of connections. Your house may be flooded if the hose gets out of its housing during
water discharge.
Important:
•The hose should be attached to a height of maximum 80 cm.
•You must be careful not the pinch or bend the hose.
•The end of the hose should not be bent, it should not be stepped on and it must not be folded between the drain and the machine.
Adjusting the feet
In order to ensure that your machine operates more silently and vibration-free, it must stand level and balanced on its feet. Balance the machine by adjusting the feet.
Rotate the feet to adjust until the machine stands level and firmly.
CNever unscrew the adjustable feet from their housings.
First use
•To have the product ready for operation before calling the authorised service agent, make sure that its location and power supply installations are appropriate. If they are not, call a qualified electrician to have any necessary arrangements carried out.
•Make sure that the power connections of the product are in accordance with the instructions given in relevant chapters of this manual.
Disposing of packaging material
Packaging materials are dangerous to children. Keep packaging materials in a safe place out of reach of children. Packaging materials of your product are manufactured from recyclable materials. Sort and dispose of them in accordance with recycled waste instructions. Do not dispose of them with normal domestic
waste.
Transportation of the machine
1.Unplug the machine from the mains.
2.Remove the water drain and vent connections (if any).
3.Drain water remaining in the machine completely before transportation.
Disposing of the old machine
Dispose of your old machine in an environmentally friendly manner.
Refer to your local dealer or solid waste collection centre in your area to learn how to dispose of your machine.
Before disposing of your old machine, cut off the power cable plug and make the loading door lock unusable to avoid dangerous conditions to children.
9 EN
Loading...