Beko DDT25400B, DDT25400W, DDT25400X, DDT28410X, DDT28430X User manual [EN]

	Dishwasher
	Installation Manual
	DDT25400B	DIT25400
	DDT25400GB
		DIT28430
	DDT25400W
		DIT29430
	DDT25400X
		DUT25400B
	DDT25400XP
		DUT25400W
	DDT28410X
		DUT25400X
	DDT28430X
		DUT28430W
	DDT28430XP
		DUT28430X
	DDT29430X
	USA
	Document Number : 15 0625 0100_AA_USA/ 02-03-16.(10:36)

To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use.

INTRODUCTION	1
1. IMPORTANT SAFETY INSTRUCTIONS	1
1.1 INSPECT THE DISHWASHER	2
2. TOOLS WHICH MAY BE NEEDED	3
3. MATERIALS WHICH MAY BE NEEDED	3
4. MATERIALS SUPPLIED	4
4.1 PARTS SUPPLIED	4
4.2 MANUAL BAG	4
4.3 DISHWASHER PARTS BAG 1	4
4.4 DISHWASHER PARTS BAG 2	4
4.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER	4
5. DISHWASHER SPECIFICATIONS	5
5.1 TECHNICAL FEATURES	5
6. ENCLOSURE PREPARATION	6
6.1 ELECTRICAL PREPARATION	6
6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS	6
6.3 ADJUSTING HEIGHT	7
6.4 INSTALLING THE SIDE TRIM STRIPS	7
6.5 PREPARING THE WATER CONNECTION (A)	8
6.6 DRAIN PREPARATION	9
6.7 STEAM PROTECTION FOIL	10
7. PLACEMENT OF DISHWASHER INTO THE OPENING	11
7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS	11
7.2 READJUSTING FOOT LEVELS	16
7.3 ADJUSTING THE MOVABLE TOE KICK	16
7.4 INSTALLING THE OUTER DOOR	17
8. INSTALLER CHECKLIST	23
9. FINAL INSTRUCTIONS	23
10. SELF HELP HINTS:	23

INTRODUCTION

Please read this installation manual and particularly the safety instructions

completely and carefully. They will save you time and effort and help to ensure optimum dishwasher performance.

Be sure to observe all listed warnings and cautions. Look particularly for the icons with exclamation marks inside. The information icon also will provide important references.

WARNING CAUTION

Ý Notice

WARNING:

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation which, if not avoided, may result in injury. It may also be used to alert against unsafe practices.

Notice:

Indicates a potentially hazardous situation which, if not avoided, may result in damage to the dishwasher, the table-ware, the equipment or the environment.

1. IMPORTANT SAFETY INSTRUCTIONS

In addition to these instructions, the dishwasher shall be installed:

•• In accordance with all local codes or, in absence of a local code,

•• In the United States, with the National Electric Code,

•• In Canada, with the Canadian Electric Code C22.1-latest edition/Provincial and Municipal codes and/or local codes.

NOTICE :

Read these installation instructions completely before installing and follow them carefully. Save these installation instructions and pass them on to any future user.

WARNING

When installing the dishwasher, follow basic precautions, including

the following:

•• The dishwasher could only be converted from cord-connected to permanently connected by an authorized service representative. (If needed contact your dealer to

schedule an authorized service agent for conversion with an appropriate conversion kit)

•• Installation and repair should be performed by a qualified installer. Work by unqualified persons could be dangerous and may void the warranty.

NOTICE :

The dishwasher should be installed by an insured licensed plumber, contractor or trained installer. Installation performed by persons other than this could result in

improper installation and property damage.

•• Do not operate the appliance if damaged, malfunctioning, partially disassembled or if it has missing or broken parts.

•• Also follow the safety instructions of the user manual.

•• To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation.

•• Only connect the dishwasher to the power supply when all installation and plumbing work is complete.

1 USA

•• If the dishwasher is installed in a location that experiences freezing temperatures (e.g. in a vacation home, cabin, etc.), you must drain all the water from the dishwasher’s interior. Water system ruptures that occur as a result of freezing are not covered by warranty.

•• Dishwasher must be secured to adjacent cabinetry using the brackets provided. Failure to do this may cause damage to property or bodily injury.

•• Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload. The dishwasher

is designed for an electrical supply of 120 V (volts), 60 Hz (hertz), AC,

connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breakers rated for 15 amperes. Electrical supply conductors shall be a minimum of # 16 AWG copper wire rated at 75 °C (167 °F) or higher. These requirements must be met to prevent injury and machine damage. Consult a qualified electrician if in doubt.

•• Do not use any extension cord or portable outlet device to connect the dishwasher to a power supply.

•• Ensure that any plastic wrappings, bags, small pieces etc. are disposed of safely and kept out of the reach of children. Danger of suffocation!

•• Remove the door to the washing compartment when removing an old dishwasher from service or discarding it. Ensure that the appliance presents no danger to children while being stored for disposal.

•• Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials.

NOTICE :

•• The dishwasher drain hose must be installed with a drain loop at least 28” (710mm) off the cabinet floor; otherwise the dishwasher may not drain properly.

•• This dishwasher is intended for residential use only, and should not be used in commercial establishments.

•• New installation - If the dishwasher is a new installation, most of the work must be done before the dishwasher is moved into place.

•• Replacement - If the dishwasher is replacing another dishwasher, check the existing dishwasher connections for compatibility with the new dishwasher, and replace parts as necessary.

1.1 INSPECT THE DISHWASHER

After unpacking the dishwasher and prior to installation, thoroughly inspect the dishwasher for possible freight or cosmetic damage. Report any damage immediately.

NOTICE :

•• Cosmetic defects must be reported within 10 days of installation.

•• Do not discard any bags or items that come with the original package until after the entire installation has been completed.

2 USA

2. TOOLS WHICH MAY BE NEEDED

3. MATERIALS WHICH MAY BE NEEDED

(Additional materials may be required to comply with local codes)

Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line.

90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg.

UL listed conduit connector or strain relief.

Teflon tape or other pipe thread compound to seal plumbing connections.

Shut-off valve and fittings appropriate for hot water supply line (copper tubing/compression fitting, or braided hose).

Silicone

Glue

3 USA

4. MATERIALS SUPPLIED

a.	x1
b.	x1
c.	x1
d.	x6
e.	x1
f.	x1
g.	x1
h.	x1
j.	x1
k.	x1
l.	x1
m.	x1
n.	x2
o.	x1
p.	x1
r.	x2
s.	x2
t.	x2
v.	x2
y.	x4
z.	x1

4.1 PARTS SUPPLIED

Parts for your dishwasher will come in several plastic bags. Check your parts bags shown to make sure you have all the parts as listed to the left.

4.2 MANUAL BAG

The dishwasher comes with a manual bag containing:

•• User manual,

•• Installation manual

4.3 DISHWASHER PARTS BAG 1

This dishwasher bag comes with the following parts:

a.Side Trim Strips (Left)

b.Side Trim Strips (Right)

c.Adjusting Wrench

d.Screws Ø 1/8” x 5/8” (Ø 3.5

mmx 14 mm)

e.Mounting Bracket Left

f.Mounting Bracket Right

g.Spring Clamp

h.Screw Clamp

j.Rubber Connector

k.Toe Kick Bracket - Left

l.Toe Kick Bracket – Right

m.Edge Protector

n.Clips

o.Toe Kick (toe kick without slots)

p.Toe Kick (MODEL DEPENDING)

r.Screws Ø 1/8” x 3/8” (Ø 3.9

mmx 9 mm)

s.Plastic Caps

t.Screws Ø 3/16” x 1/4” (Ø 4mm x 6mm)

z.Steam Protection Foil

4.4 DISHWASHER PARTS BAG 2

(MODEL DEPENDING)

In addition to the manual bag and the dishwasher parts bag (dishwasher models which can accept a wooden kitchen door) also come with a door panel installation kit which contains:

v. Screws Ø 1/8” x 5/8” (Ø 3.5mm x 14mm)

y. Screws Ø 3/16” x 13/4” (Ø 4mm x 43mm)

4.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER

a.Side Trim Strips (Left)

b.Side Trim Strips (Right)

o.Toe Kick (toe kick without slots)

p.Toe Kick (MODEL DEPENDING)

4 USA

5. DISHWASHER SPECIFICATIONS

<![if ! IE]> <![endif]>357	<![if ! IE]> <![endif]>911mm)-
<![if ! IE]> <![endif]>”
<![if ! IE]> <![endif]>8
<![if ! IE]> <![endif]>/
<![if ! IE]> <![endif]>-	<![if ! IE]> <![endif]>(861mm
<![if ! IE]> <![endif]>8
<![if ! IE]> <![endif]>/
<![if ! IE]> <![endif]>33 7

239
/
	16”
(598m
	m)

<![if ! IE]>

<![endif]>34” - 361/4” (864mm - 920mm)

24”		)
(610	mm

24”
(610	mm)

	max
24”	max)	<![if ! IE]> <![endif]>max 500mm
(610mm

5.1 TECHNICAL FEATURES

	Load capacity	14 place settings
	Permissible water	4.35 - 145 psi (0.3 - 10 bars)
	pressure
	Electrical connection	120 V (volts), 12 A (amps), 60Hz (hertz)
	Total power	1400 W (watts)
	Heater power	1240 W (watts)

NOTICE :

Because we continually strive to improve our products, we may change our specifications and design without prior notice.

This device corresponds to the following directives: UL 749 Household Dishwasher directive.

5 USA

6. ENCLOSURE PREPARATION

6.1 ELECTRICAL PREPARATION

WARNING

The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amperes.

A

B

WARNING

Dishwasher must be secured to adjacent cabinetry using the mounting brackets provided. Failure to do this may cause damage to property or bodily injury.

<![if ! IE]> <![endif]>357	<![if ! IE]> <![endif]>911mm)-
<![if ! IE]> <![endif]>”
<![if ! IE]> <![endif]>8
<![if ! IE]> <![endif]>/
<![if ! IE]> <![endif]>-	<![if ! IE]> <![endif]>(861mm
<![if ! IE]> <![endif]>8
<![if ! IE]> <![endif]>/
<![if ! IE]> <![endif]>33 7

6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS

B

A

Place the two mounting brackets into the top corners of the dishwasher.

Fix the mounting brackets (A) to the top corners of the dishwasher, with the screws supplied.

Bend sides of mounting brackets (B) in order to fix from sides (if necessary).

115/16”

(50mm)

6 USA