Behringer 1016 Quick Start Guide
Quick Start Guide
(6) (7)
DUAL NOISE / RANDOM
VOLTAGE GENERATOR
MODULE 1016
Legendary 2500 Series Dual Noise
Source Module for Eurorack
Controls
(1)
(2)
(3)
(4)
(5)
Power Connection
The unit com es with the requi red power cable for c onnecting
to a standa rd Eurorack power su pply system. Fol low these
steps to con nect power to the mo dule. It is easier to make
these con nections bef ore the module has be en mounted into
a rack cas e.
1. Turn the power su pply or rack case p ower o and
disconne ct the power cabl e.
2. Insert the 16- pin connector o n the power cable into t he
socket on t he power supply or rac k case. The connec tor has
a tab that wi ll align with the gap in t he socket, so it can not
be inser ted incorrec tly. If the power supply d oes not have
a keyed socke t, be sure to orient pi n 1 (-12 V) with the red
stripe o n the cable.
3. Insert the 10 -pin connecto r into the socket on th e back of
the modul e. The connector ha s a tab that will align wi th the
socket for correct orientation.
4. After both en ds of the power cable hav e been securely
attac hed, you may mount the mo dule in a case and tur n on
the power supply.
(1) LEDs – Indica te whether the asso ciated knob is ac tive.
(2 ) NOI SE knob – Attenuates t he output of the noi se
generator.
(3 ) SLOW R ANDOM knob – Attenu ates the output of th e
slow random voltage generator.
(4 ) WHITE /PINK/OFF switch – Selec ts between w hite or
pink noise, or disengage the output.
(5 ) OFF/ON sw itch – Engages or dis engages the slow
random voltage output.
(6 ) NOI SE A/B – Send the nois e A and B signals to other
modules v ia 3.5 mm TS cable.
(7 ) R ANDOM A/B – Send the r andom voltage sign als to other
modules v ia 3.5 mm TS cable.
V 1.0
Installation
The neces sary screws ar e included with th e module for mount ing
in a Eurorac k case. Connect t he power cable bef ore mounting.
Dependi ng on the rack case, th ere may be a series of xed holes
spaced 2 HP ap art along the leng th of the case, or a tr ack that
allows indi vidual threaded p lates to slide along th e length
of the cas e. The free-movi ng threaded plate s allow precise
positio ning of the module, bu t each plate should be p ositioned in
the approx imate relation to th e mounting holes in yo ur module
before attaching the screws.
Hold the mo dule against the Eur orack rails so that e ach of the
mounting h oles are aligned wi th a threaded rail o r threaded
plate. Att ach the screws par t way to start, w hich will allow
small adjus tments to the pos itioning while you g et them all
aligned. After the nal position has been established, tighten the
screws d own.
Specications
Outputs
Noise
Type 2 x 3.5 mm TS jacks,
Impedance 1 kΩ, unbalanced
Max output level ±5 V
Random
Type 2 x 3.5 mm TS jacks,
Impedance 1 kΩ, unbalanced
Max output level ±5 V
Controls
Noise Attenuates noise
Random Attenuates voltage output
White/pink/o Selects white or pink noise,
Random on/o Engages or disengages
Power
Power supply Eurorack
Current draw 45 mA (+12 V),
Physical
Dimensions 42 x 71 x 129 mm
Rack units 14 HP
Weight 0.13 kg (0.29 lbs)
DC coupled
DC coupled
generator output
or o
voltage generator
15 mA (-12 V)
(1.7 x 2.8 x 5.1")
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake,
Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.
Loading...