Behringer 1006 Quick Start Guide
Quick Start Guide
FILTAMP MODULE 1006
Legendary 2500 Series 24 dB Low-Pass
VCF and VCA Module for Eurorack
Controls
(1) (2) (3)
(4)
(5)
(6)
(7)
(8)
(12) (13) (14) (15) (16) (17)
(1) FILT ER – Adjust s the cuto frequ ency for the lter.
(2 ) FILTER RESONANCE – Bo osts the reson ance frequencie s
selected with the Filter knob, potentially causing
VCF oscillat ion.
(3 ) AMPLIFIER GAIN – Co ntrols the level of th e VCA.
(4 ) KE YBOARD knob – Atte nuate the voltage co nnected to
the KYB D input, which cont rols the cuto fre quency of
the lter.
(5 ) IN B kn ob – Adjusts the lev el of the signal conne cted to
the IN B input .
(6 ) C V 2 to VCF knob – Attenuat e the voltage that is pa ssed
from the C V 2 input to the VCF.
(7 ) IN A kn ob – Adjusts the lev el of the signal conne cted to
the IN A input .
(8 ) C V 1 to VCF knob – Attenuat e the voltage that is pa ssed
from the C V 1 input to the VCF.
(9)
(10)
(11)
(9 ) EX PONENTIAL/LINEAR switc h – Select betw een a linear
or more natu ral exponentia l VCA response.
(10) CV 2 to VCA k nob – Attenuate the vo ltage that is passe d
from the C V 2 input to the VCA.
(11) CV 1 to VCA k nob – Attenuate the vo ltage that is passe d
from the C V 1 input to the VCA.
(12 ) IN A – Connect an i nput signal via 3.5 mm TS c able.
(13 ) IN B – Connect a n input signal via 3.5 mm T S cable.
(14) KYBD – Conne ct a voltage that c an be used to control t he
VCF frequency.
(15) CV 1 – Conne ct a voltage that c an be used to control t he
VCF freque ncy or VCA level.
(16) CV 2 – Connec t a voltage that can b e used to control th e
VCF freque ncy or VCA level.
(17) OUT – Send the pr ocessed signal to ot her modules via
3.5 mm TS cabl e.
Power Connection
The unit com es with the requi red power cable for c onnecting
to a standa rd Eurorack power su pply system. Fol low these
steps to con nect power to the mo dule. It is easier to make
these con nections bef ore the module has be en mounted into
a rack cas e.
1. Turn the power supp ly or rack case power o and
disconne ct the power cabl e.
2. Ins ert the 16-pin conn ector on the power c able into the
socket on t he power supply or rac k case. The connec tor has
a tab that wi ll align with the gap in t he socket, so it can not
be inser ted incorrec tly. If the power supply d oes not have
a keyed socke t, be sure to orient pi n 1 (-12 V) with the red
stripe o n the cable.
3. Ins ert the 10-pin co nnector into the s ocket on the back of
the modul e. The connector ha s a tab that will align wi th the
socket for correct orientation.
4. Af ter both ends of the po wer cable have been se curely
attac hed, you may mount the mo dule in a case and tur n on
the power supply.
V 1.0
Installation
The neces sary screws ar e included with th e module for mount ing
in a Eurorac k case. Connect t he power cable bef ore mounting.
Dependi ng on the rack case, th ere may be a series of xed holes
spaced 2 HP ap art along the leng th of the case, or a tr ack that
allows indi vidual threaded p lates to slide along th e length
of the cas e. The free-movi ng threaded plate s allow precise
positio ning of the module, bu t each plate should be p ositioned in
the approx imate relation to th e mounting holes in yo ur module
before attaching the screws.
Hold the mo dule against the Eur orack rails so that e ach of the
mounting h oles are aligned wi th a threaded rail o r threaded
plate. Att ach the screws par t way to start, w hich will allow
small adjus tments to the pos itioning while you g et them all
aligned. After the nal position has been established, tighten the
screws d own.
Specications
Inputs
In A/B
Type 2 x 3.5 mm TS jacks,
Impedance 70 kΩ, unbalanced
Max input level +14 dBu
Keyboard
Type 3.5 mm TS jack, DC coupled
Impedance 50 kΩ, unbalanced
CV range 0 to 10 V
CV 1/2
Type 2 x 3.5 mm TS jacks,
Impedance 50 kΩ, unbalanced
CV range 0 to 10 V
Outputs
Type 3.5 mm TS jack, DC coupled
Impedance 1 kΩ, unbalanced
Max output level +14 dBu
DC coupled
DC coupled
Controls
In A/B -∞ to unity gain
Keyboard 20 Hz to 20 kHz, 1 V/octave
CV 1/2 VCF 20 Hz to 20 kHz, 1 V/octave
CV 1/2 VCA -∞ to unity gain
Filter Cuto frequency,
20 Hz to 20 kHz
Filter resonance O to self resonance
Amplier gain -∞ to unity gain
Amplier control mode Linear or exponential
VCA control
Power
Power supply Eurorack
Current draw 22 mA (+12 V),
20 mA (-12 V)
Physical
Dimensions 43 x 81 x 129 mm
(1.7 x 3.2 x 5.1")
Rack units 16 HP
Weight 0.17 kg (0.37 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake,
Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.
Loading...