BECKHOFF CB3056 User Manual

CB3056

Manual

rev. 1.2

Beckhoff Automation GmbH phone: +49 (0) 52 46/963-0 Eiserstr. 5 fax: +49 (0) 52 46/963-198 33415 Verl email: info@beckhoff.de Germany web: www.beckhoff.de

Contents

0 Document History

Version Changes

0.1 first pre-release

1.0 first complete version

1.1 max RAM updated to 16 GB, BIOS setup features updated.

1.2 new HDMI/DP connector, resulting in new feature list (one more USB channel), new block diagram and new dimensional drawings

NOTE

All company names, brand names, and product names referred to in this manual are registered or unregistered trademarks of their respective holders and are, as such, protected by national and international law.

Beckhoff New Automation Technology CB3056 page 5

Chapter: Introduction Notes on the Documentation

1 Introduction

1.1 Notes on the Documentation

This description is only intended for the use of trained specialists in control and automation engineering who are familiar with the applicable national standards. It is essential that the following notes and explanations are followed when installing and commissioning these components.

1.1.1 Liability Conditions

The responsible staff must ensure that the application or use of the products described satisfy all the requirements for safety, including all the relevant laws, regulations, guidelines and standards. The documentation has been prepared with care. The products described are, however, constantly under development. For that reason the documentation is not in every case checked for consistency with performance data, standards or other characteristics. None of the statements of this manual represents a guarantee (Garantie) in the meaning of § 443 BGB of the German Civil Code or a statement about the contractually expected fitness for a particular purpose in the meaning of § 434 par. 1 sentence 1 BGB. In the event that it contains technical or editorial errors, we retain the right to make alterations at any time and without warning. No claims for the modification of products that have already been supplied may be made on the basis of the data, diagrams and descriptions in this documentation.

1.1.2 Copyright

page 6 Beckhoff New Automation Technology CB3056

Safety Instructions Chapter: Introduction

1.2 Safety Instructions

Please consider the following safety instructions and descriptions. Product specific safety instructions are to be found on the following pages or in the areas mounting, wiring, commissioning etc.

1.2.1 Disclaimer

All the components are supplied in particular hardware and software configurations appropriate for the application. Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH.

1.2.2 Description of Safety Symbols

The following safety symbols are used in this documentation. They are intended to alert the reader to the associated safety instructions.

ACUTE RISK OF INJURY!

If you do not adhere to the safety advise next to this symbol, there is immediate danger to life and health of individuals!

RISK OF INJURY!

If you do not adhere to the safety advise next to this symbol, there is danger to life and health of individuals!

HAZARD TO INDIVIDUALS, ENVIRONMENT, DEVICES, OR DATA!

If you do not adhere to the safety advise next to this symbol, there is obvious hazard to individuals, to environment, to materials, or to data.

NOTE OR POINTER

This symbol indicates information that contributes to better understanding.

Beckhoff New Automation Technology CB3056 page 7

Chapter: Introduction Essential Safety Measures

1.3 Essential Safety Measures

1.3.1 Operator's Obligation to Exercise Diligence

The operator must ensure that

o the product is only used for its intended purpose o the product is only operated in sound condition and in working order o the instruction manual is in good condition and complete, and always available for reference at the

location where the products are used

o the product is only used by suitably qualified and authorised personnel o the personnel is instructed regularly about relevant occupational safety and environmental protection

aspects

o the operating personnel is familiar with the operating manual and in particular the safety notes

contained herein

1.3.2 National Regulations Depending on the Machine Type

Depending on the type of machine and plant in which the product is used, national regulations governing the controllers of such machines will apply, and must be observed by the operator. These regulations cover, amongst other things, the intervals between inspections of the controller. The operator must initiate such inspections in good time.

1.3.3 Operator Requirements

o Read the operating instructions All users of the product must have read the operating instructions for the system they work with. o System know-how All users must be familiar with all accessible functions of the product.

page 8 Beckhoff New Automation Technology CB3056

Functional Range Chapter: Introduction

1.4 Functional Range

NOTE

The descriptions contained in the present documentation represent a detailed and extensive product description. As far as the described motherboard was acquired as an integral component of an Industrial PC from Beckhoff Automation GmbH, this product description shall be applied only in limited scope. Only the contractually agreed specifications of the corresponding Industrial PC from Beckhoff Automation GmbH shall be relevant. Due to several models of Industrial PCs, variations in the component placement of the motherboards are possible. Support and service benefits for the built-in motherboard will be rendered by Beckhoff Automation GmbH exclusively as specified in the product description (inclusive operation system) of the particular Industrial PC.

Beckhoff New Automation Technology CB3056 page 9

Chapter: Overview Features

2 Overview

2.1 Features

The CB3056 is a highly complex 3,5-inch board which incorporates complete motherboard functionality. It's based on Intel®'s QM67 chipset combined with an rPGA988B CPU socket for Intel® CPUs of the 2nd Generation Core™ and Celeron® families. Modern DDR3 technology provides top-notch memory performance, accommodating up to 16 GByte of RAM (DDR3-1066/1333/1600) via SO-DIMM204. It also provides a PCI bus (via mPCI connector), a PCI-Express bus (via a 2x40 pin custom connector) and additional peripheral devices such as four serial interfaces, two Gigabit Ethernet interfaces (LAN), four SATA channels (two of which offering up to 6Gb/s), an audio interface (HDA 5.1), eleven USB channels, and two DVI/HDMI connectors with CRT available through DVI-I, and DisplayPort available on a 30pin I-PEX connector.

Power VCCCore; VTT;

DDRVTT, GFXVCC

1,05V; 1,5V; 1,8V; 3,3V

Intel® Core™ i7-

2710QE, i5-2510E,

Celeron® B810

MEMORY

2x SO-DIMM204

DDR3-

1066/1333/1600

(dual channel)

SPI

Intel® QM67 PCH

PCIe to PCI

Bridge

PI7C9X111SL

PCI

mPCI

1.5/3 Gb/s

NXP®

PCA9535

RealTek®

ALC889

SMSC®

SCH3114

FAN 1-3

FDI

DMI

CRT

DVI/HDMI

DVI/HDMI/DP

SMBus

HDA Link

1.5/3/6 Gb/s

LPC

SMBus

USB1-11

PCIe

LAN1

LAN2

PCIe (x1)

Intel®

82579L

Intel®

82574L

BIOS

USB 2.0

o Socket rPGA988B o Suitable CPUs: Intel® Core™ i7-2710QE, i5-2510E, Celeron® B810 o Chipset Intel® QM67 PCH o Two SO-DIMM204 sockets for up to 16 GByte DDR3-1066/1333/1600 RAM o PCI bus via mPCI connector o PCI-Express bus (four x1 or one x4) via 2x40pin custom connector o Four serial interfaces COM1 to COM4 o Two LAN interfaces Ethernet 10/100/1000 (Base-T) o Four SATA channels (two of which up to 6Gb/s transfer rate) o PS2 keyboard / mouse interface o 11 USB 2.0 interfaces (4x external, 6x internal, 1x on I-PEX connector) o BIOS AMI® Aptio o CRT connection o Two DVI/HDMI connectors (1x DVI-I, 1x I-PEX with DisplayPort capability) o HDA compatible sound controller with SPDIF in and out o 8x GPIO o RTC with external CMOS battery o 5V supply o Format: 102 mm x 147 mm

8x GPIO

SPDIF i SPDIF o LINE IN LINE OUT MIC

2x SATA 2x SATA

KB MS

COM1-4

page 10 Beckhoff New Automation Technology CB3056

Specifications and Documents Chapter: Overview

2.2 Specifications and Documents

In making this manual and for further reading of technical documentation, the following documents, specifications and web-pages were used and are recommended.

§ PCI specification Version 2.3 resp. 3.0

www.pcisig.com

§ Mini-PCI specification Version 1.0

www.pcisig.com

§ PCI Express® Base specification Version 2.0

www.pcisig.com

§ ACPI specification Version 3.0

www.acpi.info

§ USB specifications

www.usb.org

§ SM-Bus specification Version 2.0

www.smbus.org

§ Intel® Chip Description 2nd Gen. Intel® Core™ Processor Family Mobile datasheet

www.intel.com

§ Intel® Chipset Description Intel® 6 Series Chipset datasheet

www.intel.com

§ Intel® Chip Description 82574L Datasheet

www.intel.com

§ Intel® Chip Description 82579L Datasheet

www.intel.com

§ Realtek® Chip Description ALC885/889 Datasheet

www.realtek.com.tw

§ SMSC® Chip Description SCH3114 Datasheet

www.smsc.com

(NDA required)

§ American Megatrends® Aptio™ Text Setup Environment (TSE) User Manual

www.ami.com

§ American Megatrends® Aptio™ 4.x Status Codes

www.ami.com

Beckhoff New Automation Technology CB3056 page 11

Chapter: Connectors Specifications and Documents

3 Connectors

This section describes all the connectors found on the CB3056.

CAUTION

For most interfaces, the cables must meet certain requirements. For instance, USB 2.0 requires twisted and shielded cables to reliably maintain full speed data rates. Restrictions on maximum cable length are also in place for many high speed interfaces and for power supply. Please refer to the respective specifications and use suitable cables at all times.

page 12 Beckhoff New Automation Technology CB3056

Connector Map Chapter: Connectors

3.1 Connector Map

Please use the connector map below for quick reference. Only connectors on the component side are shown. For more information on each connector refer to the table below.

Ref-No. Function Page

P500/1/2/3 "SATA Interfaces" p. 27 U600/1 "Memory" p. 17 P700 "GPIO" p. 35 P900 "PCI-Express" p. 31 P901 "Mini-PCI" p. 33 P1000/1100 "LAN" p. 25 P1300 "VGA/DVI" p. 20 P1301 "DVI/HDMI/DisplayPort" p. 21 P1400 "Audio" p. 26 P1401 "Fan Connectors" p. 24 P1402 "System" p. 16 P1500 "Serial Interface COM1" p. 28 P1503/5 "Serial Ports COM2 through COM4" p. 29 P1501/2 "USB 1-4" p. 23 P1504/6 "USB 5-10" p. 24 P1700 "Power Supply" p. 15

Beckhoff New Automation Technology CB3056 page 13

Chapter: Connectors CPU Socket

3.2 CPU Socket

The CB3056 board has an rPGA988B CPU socket accomodating certain models of Intel®’s 2nd Generation Core™ and Celeron® family CPUs. The rPGA988B is a ZIF (Zero Insertion Force) socket, which means that you can insert the processor without there being any resistance. There is only one orientation in which the processor will fit into the socket. Once the processor is in place the fastening screw must be tightened to ensure proper electrical contact. The package type allows a maximum die temperature of 100 degrees Celsius and accords highest possible security even in rough environment. The processor includes a second level cache of up to 6 MByte, depending on which model is used. Furthermore the processors offer many features known from the desktop range such as MMX2, serial number, loadable microcode etc.

NOTE

Processors must be ordered separately. The board ships without a CPU.

page 14 Beckhoff New Automation Technology CB3056

Power Supply Chapter: Connectors

3.3 Power Supply

The power supply of the hardware module is realized via a 2x8-pin connector (Molex PS 43045-16xx, mating connector: Molex PS 43025-16xx). The 12 volt supply is needed for PCI-Express cards and for the fan connector. COM3 RXD and TXD can also be used for connecting a second power supply unit, e. g. for UPS. As an ordering option SMBus signals SCL/SDA can be provided (replacing COM3 TXD/RXD).

Description Name Pin Name Description

COM3 transmit data TXD 1 9 RXD COM3 receive data PSU on PS-ON 2 10 RESET# PSU reset powerbutton PSU PWRBTN# 3 11 SVCC standby-supply 5V 12 volt supply 12V 4 12 12V 12 volt supply ground GND 5 13 GND ground ground GND 6 14 GND ground 5 volt supply VCC 7 15 VCC 5 volt supply 5 volt supply VCC 8 16 VCC 5 volt supply

Beckhoff New Automation Technology CB3056 page 15

Chapter: Connectors System

3.4 System

A number of signals for system control and for SMBus communication are provided through a 2x12 pin connector (FCI 98424-G52-24LF). This connector combines signals for power button, reset, keyboard, speaker, and several LEDs such as harddisk LED, and suspend LED, and three additional LEDs which are driven by GPIOs. Of these three GPIO-LEDs, LED1 and LED2 are already provided with a series resistor. SMBus capable devices can also be connected.

Pinout 2x12pin connector:

Description Name Pin Name Description

ground GND 1 13 3.3V 3.3V supply reset to ground RSTBTN# 2 14 PWRBTN# on/suspend button LED suspend / ACPI S-LED 3 15 S3.3V standby supply 3.3V LED harddisk SATALED 4 16 GPIOLED3 LED GPIO device 3 LED GPIO device 1 GPIOLED1 5 17 BATT battery LED GPIO device 2 GPIOLED2 6 18 SMBALERT# SMB alert SMB Clock SMBCLKEX 7 19 SMBDATEX SMB data speaker to 5V SPEAKER 8 20 SVCC standby supply 5V keyboard clock KCLK 9 21 KDAT keyboard data ground GND 10 22 VCC 5V supply ground GND 11 23 VCC 5V supply ground GND 12 24 VCC 5V supply

page 16 Beckhoff New Automation Technology CB3056

Memory Chapter: Connectors

3.5 Memory

Conventional SO-DIMM204 memory modules, as familiar from notebook computers, are used to equip the board with memory. For technical and mechanical reasons it is possible that particular memory modules cannot be employed. Please ask your distributor for recommended memory modules. With currently available SO-DIMM204 modules a memory extension up to 16 GByte is possible (DDR3-1066/1333/1600). All timing parameters for different memory modules are automatically set by BIOS.

Description Name Pin Name Description

memory reference current REF-DQ 1 2 GND ground ground GND 3 4 DQ4 data 4 data 0 DQ0 5 6 DQ5 data 5 data 1 DQ1 7 8 GND ground ground GND 9 10 DQS0# data strobe 0 data mask 0 DM0 11 12 DQS0 data strobe 0 + ground GND 13 14 GND ground data 2 DQ2 15 16 DQ6 data 6 data 3 DQ3 17 18 DQ7 data 7 ground GND 19 20 GND ground data 8 DQ8 21 22 DQ12 data 12 data 9 DQ9 23 24 DQ13 data 13 ground GND 25 26 GND ground data strobe 1 - DQS1# 27 28 DM1 data mask 1 data strobe 1 + DQS1 29 30 RESET# Reset ground GND 31 32 GND ground data 10 DQ10 33 34 DQ14 data 14 data 11 DQ11 35 36 DQ15 data 15 ground GND 37 38 GND ground data 16 DQ16 39 40 DQ20 data 20 data 17 DQ17 41 42 DQ21 data 21 ground GND 43 44 GND ground data strobe 2 - DQS2# 45 46 DM2 data mask 2 data strobe 2 + DQS2 47 48 GND ground ground GND 49 50 DQ22 data 22

Beckhoff New Automation Technology CB3056 page 17

Chapter: Connectors Memory

Description Name Pin Name Description

data 18 DQ18 51 52 DQ23 data 23 data 19 DQ19 53 54 GND ground ground GND 55 56 DQ28 data 28 data 24 DQ24 57 58 DQ29 data 29 data 25 DQ25 59 60 GND ground ground GND 61 62 DQS3# data strobe 3 data mask 3 DQM3 63 64 DQS3 data strobe 3 + ground GND 65 66 GND ground data 26 DQ26 67 68 DQ30 data 30 data 27 DQ27 69 70 DQ31 data 31 ground GND 71 72 GND ground clock enables 0 CKE0 73 74 CKE1 clock enables 1

1.5 volt supply 1.5V 75 76 1.5V 1.5 volt supply reserved N/C 77 78 (A15) reserved SDRAM bank 2 BA2 79 80 A14 address 14

1.5 volt supply 1.5V 81 82 1.5V 1.5 volt supply address 12 (burst chop) A12/BC# 83 84 A11 address 11 address 9 A9 85 86 A7 address 7

1.5 volt supply 1.5V 87 88 1.5V 1.5 volt supply address 8 A8 89 90 A6 address 6 address 5 A5 91 92 A4 address 4

1.5 volt supply 1.5V 93 94 1.5V 1.5 volt supply address 3 A3 95 96 A2 address 2 address 1 A1 97 98 A0 address 0

1.5 volt supply 1.5V 99 100 1.5V 1.5 volt supply Clock 0 + CK0 101 102 CK1 clock 1 + Clock 0 - CK0# 103 104 CK1# clock 1 -

1.5 volt supply 1.5V 105 106 1.5V 1.5 volt supply address 10 (auto precharge) A10/AP 107 108 BA1 SDRAM bank 1 SDRAM Bank 0 BA0 109 110 RAS# row address strobe

1.5 volt supply 1.5V 111 112 1.5V 1.5 volt supply write enable WE# 113 114 S0# chip select 0 column address strobe CAS# 115 116 ODT0 on die termination 0

1.5 volt supply 1.5V 117 118 1.5V 1.5 volt supply address 13 A13 119 120 ODT1 on die termination 1 Chip Select 1 S1# 121 122 N/C reserved

1.5 volt supply 1.5V 123 124 1.5V 1.5 volt supply reserved (TEST) 125 126 REF-CA reference current ground GND 127 128 GND ground data 32 DQ32 129 130 DQ36 data 36 data 33 DQ33 131 132 DQ37 data 37 ground GND 133 134 GND ground data strobe 4 - DQS4# 135 136 DQM4 data mask 4 data strobe 4 + DQS4 137 138 GND ground ground GND 139 140 DQ38 data 38 data 34 DQ34 141 142 DQ39 data 39 data 35 DQ35 143 144 GND ground ground GND 145 146 DQ44 data 44 data 40 DQ40 147 148 DQ45 data 45 data 41 DQ41 149 150 GND ground ground GND 151 152 DQS5# data strobe 5 data mask 5 DQM5 153 154 DQS5 data strobe 5 + ground GND 155 156 GND ground data 42 DQ42 157 158 DQ46 data 46 data 43 DQ43 159 160 DQ47 data 47

page 18 Beckhoff New Automation Technology CB3056

Memory Chapter: Connectors

Description Name Pin Name Description

ground GND 161 162 GND ground data 48 DQ48 163 164 DQ52 data 52 data 49 DQ49 165 166 DQ53 data 53 ground GND 167 168 GND ground data strobe 6 - DQS6# 169 170 DQM6 data mask 6 data strobe 6 DQS6 171 172 GND ground ground GND 173 174 DQ54 data 54 data 50 DQ50 175 176 DQ55 data 55 data 51 DQ51 177 178 GND ground ground GND 179 180 DQ60 data 60 data 56 DQ56 181 182 DQ61 data 61 data 57 DQ57 183 184 GND ground ground GND 185 186 DQS7# data strobe 7 data mask 7 DQM7 187 188 DQS7 data strobe 7 + ground GND 189 190 GND ground data 58 DQ58 191 192 DQ62 data 62 data 59 DQ59 193 194 DQ63 data 63 ground GND 195 196 GND ground SPD address 0 SA0 197 198 EVENT# Event

3.3 volt supply 3.3V 199 200 SDA SMBus data SPD address 1 SA1 201 202 SCL SMBus clock termination current VTT 203 204 VTT termination current

Beckhoff New Automation Technology CB3056 page 19

Chapter: Connectors VGA/DVI

3.6 VGA/DVI

The module is equipped with a standard DVI-I-connector, which can be used to connect a DVI capable device, a standard VGA monitor or an HDMI capable device. External cable adapters that convert from DVI to VGA or HDMI are required to connect standard VGA or HDMI devices.

Pinout DVI-I:

Name Description

1 TMDSDAT2# DVI data 2 2 TMDSDAT2 DVI data 2 + 3 GND ground 4 N/C reserved 5 N/C reserved 6 DDC CLK DDC clock (DVI/VGA) 7 DDC DAT DDC data (DVI/VGA) 8 VSYNC VGA vertical sync 9 TMDSDAT1# DVI data 1 10 TMDSDAT1 DVI data 1 + 11 GND ground 12 N/C reserved 13 N/C reserved 14 VCC 5 volt supply 15 GND ground 16 HP_DETECT hot plug detect 17 TMDSDAT0# DVI data 0 18 TMDSDAT0 DVI data 0 + 19 GND ground 20 N/C reserved 21 N/C reserved 22 GND ground 23 TMDS CLK DVI clock 24 TMDS CLK# DVI clock C1 RED VGA red C2 GREEN VGA green C3 BLUE VGA blue C4 HSYNC VGA horizontal sync C5 GND ground

page 20 Beckhoff New Automation Technology CB3056

DVI/HDMI/DisplayPort Chapter: Connectors

3.7 DVI/HDMI/DisplayPort

The CB3056 provides a second DVI interface which is realized as a 30pin flat cable header (I-PEX Cabline-VS 20455-030E). Analog VGA is not available on this connector. However, an HDMI device or DisplayPort device can be connected. The connector also carries an additional USB interface.

Pinout 30pin connector DVI/HDMI/DisplayPort:

1 TMDS0#/DP2# DVI Data 0 - / DP Lane 2 2 TMDS0/DP2 DVI Data 0 + / DP Lane 2 + 3 TMDS1#/DP1# DVI Data 1 - / DP Lane 1 4 TMDS1/DP1 DVI Data 1 + / DP Lane 1 + 5 TMDS2#/DP0# DVI Data 2 - / DP Lane 0 6 TMDS2/DP0 DVI Data 2 + / DP Lane 0 + 7 TMDSCLK#/DP3# DVI Clock - / DP Lane 3 8 TMDSCLK/DP3 DVI Clock + / DP Lane 3 + 9 N/C reserved 10 SEL_DVI/DP# DVI-DisplayPort Select 11 DDCK/DPAUX EDID Clock / DP Aux + 12 DDDA/DPAUX# EDID Data / DP Aux 13 VCC 5V supply 14 GND ground 15 HPD hot plug detect 16 USBVCC 5V supply for USB 17 USBVCC 5V supply for USB 18 N/C reserved 19 N/C reserved 20 N/C reserved 21 N/C reserved 22 USB# USB 23 USB USB + 24 N/C reserved 25 N/C reserved 26 3.3V 3.3V supply 27 3.3V 3.3V supply 28 VCC 5V supply

Name Description

Beckhoff New Automation Technology CB3056 page 21

Chapter: Connectors DVI/HDMI/DisplayPort

Name Description

29 VCC 5V supply 30 VCC 5V supply

page 22 Beckhoff New Automation Technology CB3056

USB 1-4 Chapter: Connectors

3.8 USB 1-4

The USB channels 1 to 4 are available as standard USB connectors. The USB channels support USB 2.0. You may note that the setting of USB keyboard or USB mouse support in the BIOS-setup is only necessary and advisable, if the OS offers no USB-support. BIOS-setup can be changed with a USB keyboard without enabling USB keyboard support. Running Windows with these features enabled may lead to significant performance or functionality limitations. Every USB interface provides up to 500 mA current and is protected by an electronically resettable fuse.

Pinout USB connector for channel X:

Name Description

1 VCC 5 volt for USBX 2 USBX# minus channel USBX 3 USBX plus channel USBX 4 GND ground

Beckhoff New Automation Technology CB3056 page 23

Chapter: Connectors USB 5-10

3.9 USB 5-10

The USB channels 5 to 10 are provided via two connectors, one of which is 2x4pin, the other 2x8pin (FCI 98424-G52-08LF, FCI 98424-G52-16LF). The USB channels support USB 2.0. You may note that the setting of USB keyboard or USB mouse support in the BIOS-setup is only necessary and advisable, if the OS offers no USB-support. BIOS-setup can be changed with a USB keyboard without enabling USB keyboard support. Running Windows with these features enabled may lead to significant performance or functionality limitations. Every USB interface provides up to 500 mA current and is protected by an electronically resettable fuse.

Pinout USB 5-8

Description Name Pin Name Description

5 volt for USB5 VCC 1 9 VCC 5 volt for USB6 minus channel USB5 USB5- 2 10 USB6- minus channel USB6 plus channel USB5 USB5+ 3 11 USB6+ plus channel USB6 ground GND 4 12 GND ground ground GND 5 13 GND ground plus channel USB7 USB7+ 6 14 USB8+ plus channel USB8 minus channel USB7 USB7- 7 15 USB8- minus channel USB8 5 volt for USB7 VCC 8 16 VCC 5 volt for USB8

Pinout USB 9/10

Description Name Pin Name Description

5 volt for USB9 VCC 1 5 VCC 5 volt for USB10 minus channel USB9 USB9- 2 6 USB10- minus channel USB10 plus channel USB9 USB9+ 3 7 USB10+ plus channel USB10 ground GND 4 8 GND ground

page 24 Beckhoff New Automation Technology CB3056

LAN Chapter: Connectors

3.10 LAN

The module has two LAN interfaces both of which support 10BaseT, 100BaseT, and 1000BaseT compatible net components with automatic bandwidth selection. Controller chips are Intel® 82579L (PHY, LAN1) and 82574L (MAC/PHY, LAN2). Auto-cross and auto-negotiate functionality is available as is PXE, RPL and WOL.

Pinout LAN 10/100/1000:

Name Description

1 LAN-0 LAN channel 0 plus 2 LAN-0# LAN channel 0 minus 3 LAN-1 LAN channel 1 plus 4 LAN-1# LAN channel 1 minus 5 LAN-2 LAN channel 2 plus 6 LAN-2# LAN channel 2 minus 7 LAN-3 LAN channel 3 plus 8 LAN-3# LAN channel 3 minus

Beckhoff New Automation Technology CB3056 page 25

Chapter: Connectors Audio

3.11 Audio

Audio input and output functions can be accessed via a 2x5 pin connector (FCI 98424-G52-10LF). There are two ways to use this connector. Default functionality is the familiar audio in, audio out, and microphone. OS dependent device drivers can switch these signals to support a 5.1 output; thus in this mode no audio input signals are available. Signals "SPDIFI" and "SPDIFO" provide digital input and output. If a transformation to a coaxial or optical connector is necessary this must be performed externally.

Description Name Pin Name Description

digital output SPDIF SPDIFO 1 6 3.3V 3.3 volt supply digital input SPDIF SPDIFI 2 7 S_AGND analog ground sound sound output right / front output right AUX input right / rear output right microphone input 1 / center output

LOUT_R / FRONT_R AUXA_R / REAR_R MIC1 / CENTER

3 8 LOUT_L /

FRONT_L

4 9 AUXA_L /

REAR_L

5 10 MIC2 /

LFE

sound output left / front output left AUX input left / rear output left microphone input 2 / LFE output

page 26 Beckhoff New Automation Technology CB3056

SATA Interfaces Chapter: Connectors

3.12 SATA Interfaces

The CB3056 provides four SATA interfaces, the first two of which allowing transfer rates of up to 6 Gb/s. The other two allow transfer rates of up to 3Gb/s. All these interfaces are made available via 7pin standard connectors. RAID 0/1/5/10 is available. The required settings are made in the BIOS setup.

Pinout SATA:

Name Description

1 GND ground 2 SATATX SATA transmit + 3 SATATX# SATA transmit 4 GND ground 5 SATARX SATA receive + 6 SATARX# SATA receive 7 GND ground

Beckhoff New Automation Technology CB3056 page 27

Chapter: Connectors Serial Interface COM1

3.13 Serial Interface COM1

The serial interface COM1 is made available via a 9-pin standard DSUB-connector (male, e.g. Foxconn DM10152-H5W3-4F). Signal level is RS232. The port address and the interrupt are set via the BIOS setup.

Pinout serial port (DSUB connector):

Description Name Pin Name Description

data carrier detect DCD 1 6 DSR data set ready receive data RXD 2 7 RTS request to send transmit data TXD 3 8 CTS clear to send data terminal ready DTR 4 9 RI ring indicator ground GND 5

page 28 Beckhoff New Automation Technology CB3056

Serial Ports COM2 through COM4 Chapter: Connectors

3.14 Serial Ports COM2 through COM4

There are three more serial interfaces on the board. Of these, COM3 is available through the power connector (cf. p. 15), or, as an option, through a 2x5pin connector (FCI 98424-G52-10LF). COM2 and COM4 and made available via a 2x10 pin connector (FCI 98424-G52-20LF). Signal level is RS232. The port address and the interrupt are set via the BIOS setup.

Description Name Pin Name Description

data carrier detect COM2 DCDB 1 11 DSRB data set ready COM2 receive data COM2 RXDB 2 12 RTSB request to send COM2 transmit data COM2 TXDB 3 13 CTSB clear to send COM2 data terminal ready COM2 DTRB 4 14 RIB ring indicator COM2 ground GND 5 15 COM3.3V 3.3 volt supply data carrier detect COM4 DCDD 6 16 DSRD data set ready COM4 receive data COM4 RXDD 7 17 RTSD request to send COM4 transmit data COM4 TXDD 8 18 CTSD clear to send COM4 data terminal ready COM4 DTRD 9 19 RID ring indicator COM4 ground GND 10 20 COM3.3V 3.3 volt supply

Beckhoff New Automation Technology CB3056 page 29

Chapter: Connectors Serial Ports COM2 through COM4

When the module is ordered in standard configuration, the 2x5pin connector offers mouse and keyboard signals.

Alternative pinout of COM-connector:

Description Name Pin Name Description

keyboard clock KCLK 1 6 MCLK mouse clock keyboard data KDAT 2 7 MDAT mouse data reserved N/C 3 8 N/C reserved reserved N/C 4 9 N/C reserved ground GND 5 10 3.3V 3.3 volt supply

page 30 Beckhoff New Automation Technology CB3056

PCI-Express Chapter: Connectors

3.15 PCI-Express

The CB3056 offers a 2x40pin custom connector for the PCI-Express bus. You can connect one PCIe4x device here. Alternatively, up to four PCIe1x devices can be connected. Adapter cards featuring standard PCIe sockets or a PCIe Mini Card connector are available. Please contact your sales representative for these cards.

Pinout 2x40 pin connector PCIe:

Description Name Pin Name Description

3.3 volt supply 3.3V 1 2 12V 12 volt supply

3.3 volt stand-by S3.3V 3 4 SMBCLK1 SMB clock slot 1 PCIe reset PLTPCIE# 5 6 SMBDAT1 SMB dat slot 1 link reactivation PEWAKE# 7 8 GND ground ground GND 9 10 PECLK0 PCIe clock 0 + transmit lane 1 + PET1 11 12 PECLK0# PCIe clock 0 transmit lane 1 - PET1# 13 14 GND ground ground GND 15 16 PER1 receive lane 1 + clock enable 1 PE1CLKEN# 17 18 PER1# receive lane 1 ground GND 19 20 GND ground

3.3 volt supply 3.3V 21 22 12V 12 volt supply

3.3 volt stand-by S3.3V 23 24 SMBCLK2 SMB clock slot 2 PCIe reset PLTPCIE# 25 26 SMBDAT2 SMB dat slot 2 link reactivation PEWAKE# 27 28 GND ground ground GND 29 30 PECLK1 PCIe clock 1 + transmit lane 2 + PET2 31 32 PECLK1# PCIe clock 1 transmit lane 2 - PET2# 33 34 GND ground ground GND 35 36 PER2 receive lane 2 + clock enable 2 PE2CLKEN# 37 38 PER2# receive lane 2 ground GND 39 40 GND ground

3.3 volt supply 3.3V 41 42 12V 12 volt supply

3.3 volt stand-by S3.3V 43 44 SMBCLK3 SMB clock slot 3 PCIe reset PLTPCIE# 45 46 SMBDAT4 SMB dat slot 3 link reactivation PEWAKE# 47 48 GND ground ground GND 49 50 PECLK2 PCIe clock 2 + transmit lane 3 + PET3 51 52 PECLK2# PCIe clock 2 transmit lane 3 - PET3# 53 54 GND ground

Beckhoff New Automation Technology CB3056 page 31

Chapter: Connectors PCI-Express

Description Name Pin Name Description

ground GND 55 56 PER3 receive lane 3 + clock enable 3 PE3CLKEN# 57 58 PER3# receive lane 3 ground GND 59 60 GND ground

3.3 volt supply 3.3V 61 62 12V 12 volt supply

3.3 volt stand-by S3.3V 63 64 SMBCLK4 SMB clock slot 4 PCIe reset PLTPCIE# 65 66 SMBDAT4 SMB dat slot 4 link reactivation PEWAKE# 67 68 GND ground ground GND 69 70 PECLK3 PCIe clock 3 + transmit lane 4 + PET4 71 72 PECLK3# PCIe clock 3 transmit lane 4 - PET4# 73 74 GND ground ground GND 75 76 PER4 receive lane 4 + clock enable 4 PE3CLKEN# 77 78 PER4# receive lane 4 PCIe configure x1/x4 PECONF# 79 80 GND ground

page 32 Beckhoff New Automation Technology CB3056

Mini-PCI Chapter: Connectors

3.16 Mini-PCI

The CB3056 allows you to add expansion cards complying to the Mini-PCI standard (type III). One such card can be inserted into the Mini-PCI slot available on the board.

Description Name Pin Name Description

reserved N/C 1 2 N/C reserved reserved N/C 3 4 N/C reserved reserved N/C 5 6 N/C reserved reserved N/C 7 8 N/C reserved reserved N/C 9 10 N/C reserved reserved N/C 11 12 N/C reserved reserved N/C 13 14 N/C reserved reserved N/C 15 16 N/C reserved interrupt B INTB# 17 18 VCC 5 volt supply

3.3 volt supply 3.3V 19 20 INTA# interrupt A serial interrupt (legacy) SERIRQ 21 22 N/C reserved ground GND 23 24 S3.3V 3.3 volt supply PCI clock PCLK 25 26 PRST# reset ground GND 27 28 3.3V 3.3 volt supply PCI request REQ# 29 30 GNT# PCI grant

3.3 volt supply 3.3V 31 32 GND ground address/data 31 AD31 33 34 PME# power management event address/data 29 AD29 35 36 N/C reserved ground GND 37 38 AD30 address/data 30 address/data 27 AD27 39 40 3.3V 3.3 volt supply address/data 25 AD25 41 42 AD28 address/data 28 interrupt C INTC# 43 44 AD26 address/data 26 bus cmd/byte enables 3 CBE3# 45 46 AD24 address/data 24 address/data 23 AD23 47 48 IDSEL init device select ground GND 49 50 GND ground address/data 21 AD21 51 52 AD22 address/data 22 address/data 19 AD19 53 54 AD20 address/data 20 ground GND 55 56 PAR parity address/data 17 AD17 57 58 AD18 address/data 18

Beckhoff New Automation Technology CB3056 page 33

Chapter: Connectors Mini-PCI

Description Name Pin Name Description

bus cmd/byte enables 2 CBE2# 59 60 AD16 address/data 16 initiator ready IRDY# 61 62 GND ground

3.3 volt supply 3.3V 63 64 FRAME# cycle frame clock running CLKRUN# 65 66 TRDY# target ready system error SERR# 67 68 STOP# stop request by target ground GND 69 70 3.3V 3.3 volt supply parity error PERR# 71 72 DEVSEL# device select bus cmd/byte enables 1 CBE1# 73 74 GND ground address/data 14 AD14 75 76 AD15 address/data 15 ground GND 77 78 AD13 address/data 13 address/data 12 AD12 79 80 AD11 address/data 11 address/data 10 AD10 81 82 GND ground ground GND 83 84 AD9 address/data 9 address/data 8 AD8 85 86 CBE0# bus cmd/byte enables 0 address/data 7 AD7 87 88 3.3V 3.3 volt supply

3.3 volt supply 3.3V 89 90 AD6 address/data 6 address/data 5 AD5 91 92 AD4 address/data 4 interrupt D INTD# 93 94 AD2 address/data 2 address/data 3 AD3 95 96 AD0 address/data 0 5 volt supply VCC 97 98 N/C reserved address/data 1 AD1 99 100 N/C reserved ground GND 101 102 GND ground reserved N/C 103 104 GND ground reserved N/C 105 106 N/C reserved reserved N/C 107 108 N/C reserved reserved N/C 109 110 N/C reserved reserved N/C 111 112 N/C reserved reserved N/C 113 114 GND ground reserved N/C 115 116 N/C reserved reserved N/C 117 118 N/C reserved reserved N/C 119 120 N/C reserved lock PLOCK# 121 122 N/C reserved reserved N/C 123 124 S3.3V 3.3 volt supply

page 34 Beckhoff New Automation Technology CB3056

GPIO Chapter: Connectors

3.17 GPIO

The General Purpose Input/Output interface is made available through a 2x6 pin connector (FCI 98424-G52-12LF). To make use of this interface the GPIO chip (PCA9535BS) must be programmed accordingly. Please refer to your distributor for information on available software support.

Pinout GPIO connector:

Description Name Pin Name Description

5 volt supply VCC 1 7 VCC 5 volt supply GP input/output 10 GPIO10 2 8 GPIO14 GP input/output 14 GP input/output 11 GPIO11 3 9 GPIO15 GP input/output 15 GP input/output 12 GPIO12 4 10 GPIO16 GP input/output 16 GP input/output 13 GPIO13 5 11 GPIO17 GP input/output 17 ground GND 6 12 GND ground

Beckhoff New Automation Technology CB3056 page 35

Chapter: Connectors Fan Connectors

3.18 Fan Connectors

Three external fans (12V) can be connected to the board using a 2x5pin connector (FCI 98424-G52-10LF). Monitoring signals are available. For the monitoring to work the fans must provide a corresponding speed signal.

Pinout fan connector:

Description Name Pin Name Description

ground GND 1 6 GND ground 12V regulated fan 1 FANON1 2 7 FANON2 12V regulated fan 2 monitoring signal fan 1 FANCTL1 3 8 FANCTL2 monitoring signal fan 2 12V regulated fan 3 FANON3 4 9 FANCTL3 monitoring signal fan 3 ground GND 5 10 GND ground

page 36 Beckhoff New Automation Technology CB3056

General Remarks Chapter: BIOS Settings

4 BIOS Settings

4.1 General Remarks

In each setup page, standard values for all setup entries can be loaded. Previously saved settings are loaded by pressing F2 and factory defaults are loaded with F3. Both F2 and F3, and also F4 ("Save & Exit") always affect the whole set of setup entries. Setup entries starting with a „►" sign represent submenus. Navigation between entries is done using the arrow keys on the keyboard, with the <Enter> key being used to select an entry, which either opens up a dialog box or opens a whole new submenu of setup entries. Each setup entry has a short help text associated with it. This is displayed in the upper right hand corner of the screen.

NOTE

BIOS features and setup options are subject to change without notice. The settings displayed in the screenshots on the following pages are meant to be examples only. They do not represent the recommended settings or the default settings. Determination of the appropriate settings is dependent upon the particular application scenario in which the board is used.

Beckhoff New Automation Technology CB3056 page 37

Chapter: BIOS Settings Main

4.2 Main

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ │Set the Date. Use Tab to │ │ Board Information │switch between Data elements. │ │ Board CB3056 │ │ │ Revision 2 │ │ │ Bios Version 1.12 │ │ │ │ │ │ Processor Information │ │ │ Name SandyBridge │ │ │ Brand String Intel(R) Core(TM) i7- │ │ │ Frequency 2100 MHz │ │ │ Processor ID 206a7 │ │ │ Stepping D2 │ │ │ Number of Processors 4Core(s) / 8Thread(s) │────────────────────────────────│ │ Microcode Revision 25 │→←: Select Screen │ │ GT Info GT2 (1200 MHz) │↑↓: Select Item │ │ │Enter: Select │ │ IGFX VBIOS Version 2137 │+/-: Change Opt. │ │ Memory RC Version 1.2.2.0 │F1: General Help │ │ Total Memory 4096 MB (DDR3) │F2: Previous Values │ │ Memory Frequency 1067 Mhz │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ System Date [Mon 09/03/2012] │ESC: Exit │ │ System Time [00:47:04] │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Board

Options: none

ü Revision

Options: none

ü Bios Version

Options: none

ü Processor Information

Options: none

ü Name

Options: none

ü Brand String

Options: none

ü Frequency

Options: none

ü Processor ID

Options: none

ü Stepping

Options: none

ü Number of Processors

Options: none

ü Microcode Revision

Options: none

page 38 Beckhoff New Automation Technology CB3056

Main Chapter: BIOS Settings ü GT Info

Options: none

ü IGFX VBIOS Version

Options: none

ü Memory RC Version

Options: none

ü Total Memory

Options: none

ü Memory Frequency

Options: none

ü System Date

Options: The system date can be adjusted here.

ü System Time

Options: The system time can be adjusted here.

Beckhoff New Automation Technology CB3056 page 39

Chapter: BIOS Settings Advanced

4.3 Advanced

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Power-Supply Type [ATX] │Select the Type of the Power │ │► PCI Subsystem Settings │Supply: AT/ATX │ │► ACPI Settings │ │ │► CPU Configuration │ │ │► SATA Configuration │ │ │► Power Controller Options │ │ │► USB Configuration │ │ │► Super IO Configuration │ │ │► H/W Monitor │ │ │► Serial Port Console Redirection │ │ │► CPU PPM Configuration │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Power-Supply Type

Options: ATX / AT

ü PCI Subsystem Settings

Sub menu: see "PCI Subsystem Settings" (p. 41)

ü ACPI Settings

Sub menu: see "ACPI Settings" (p. 43)

ü CPU Configuration

Sub menu: see "CPU Configuration" (p. 44)

ü SATA Configuration

Sub menu: see "SATA Configuration" (p. 46)

ü Power Controller Options

Sub menu: see "Power Controller Options" (p. 47)

ü USB Configuration

Sub menu: see "USB Configuration" (p. 49)

ü Super IO Configuration

Sub menu: see "Super IO Configuration" (p. 50)

ü H/W Monitor

Sub menu: see "H/W Monitor" (p. 52)

ü Serial Port Console Redirection

Sub menu: see "Serial Port Console Redirection" (p. 54)

ü CPU PPM Configuration

Sub menu: see "CPU PPM Configuration" (p. 56)

page 40 Beckhoff New Automation Technology CB3056

Advanced Chapter: BIOS Settings

4.3.1 PCI Subsystem Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCI Bus Driver Version V 2.05.02 │Enables or Disables 64bit │ │ │capable Devices to be Decoded │ │ PCI 64bit Resources Handling │in Above 4G Address Space │ │ Above 4G Deconding [Disabled] │(Only if System Supports 64 │ │ │bit PCI Decoding). │ │ PCI Common Settings │ │ │ PCI Latency Timer [32 PCI Bus Clocks] │ │ │ │ │ │► PCI Express Settings │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Above 4G Decoding

Options: Enabled / Disabled

ü PCI Latency Timer

Options: 32, 64,...224, 248 PCI Bus Clocks

ü PCI Express Settings

Sub menu: see "PCI Express Settings" (p. 42)

Beckhoff New Automation Technology CB3056 page 41

Chapter: BIOS Settings Advanced

4.3.1.1 PCI Express Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCI Express Device Register Settings │Enables or Disables PCI │ │ Relaxed Ordering [Disabled] │Express Device Relaxed │ │ Extended Tag [Disabled] │Ordering │ │ No Snoop [Enabled] │ │ │ Maximum Payload [Auto] │ │ │ Maximum Read Request [Auto] │ │ │ │ │ │ PCI Express Link Register Settings │ │ │ ASPM Support [Disabled] │ │ │ WARNING: Enabling ASPM may cause some │ │ │ PCI-E devices to fail │ │ │ Extended Synch [Disabled] │ │ │ │────────────────────────────────│ │ Link Training Retry [5] │→←: Select Screen │ │ Link Training Timeout (uS) 100 │↑↓: Select Item │ │ Unpopulated Links [Disable] │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Relaxed Ordering

Options: Enabled / Disabled

ü Extended Tag

Options: Enabled / Disabled

ü No Snoop

Options: Enabled / Disabled

ü Maximum Payload

Options: Auto / 128 Bytes / 256 Bytes / 512 Bytes / 1024 Bytes / 2048 Bytes / 4096 Bytes

ü Maximum Read Request

Options: Auto / 128 Bytes / 256 Bytes / 512 Bytes / 1024 Bytes / 2048 Bytes / 4096 Bytes

ü ASPM Support

Options: Disabled / Auto / Force L0s

ü Extended Synch

Options: Enabled / Disabled

ü Link Training Retry

Options: Disabled / 2 / 3 / 5

ü Link Training Timeout (uS)

Options: 10...1000

ü Unpopulated Links

Options: Keep Link ON / Disable

page 42 Beckhoff New Automation Technology CB3056

Advanced Chapter: BIOS Settings

4.3.2 ACPI Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ ACPI Settings │Enables or Disables BIOS ACPI │ │ │Auto Configuration. │ │ Enable ACPI Auto Configuration [Disabled] │ │ │ │ │ │ Enable Hibernation [Enabled] │ │ │ ACPI Sleep State [S1 only(CPU Stop C...] │ │ │ Lock Legacy Resources [Disabled] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Enable ACPI Auto Configuration

Options: Enabled / Disabled

ü Enable Hibernation

Options: Enabled / Disabled

ü ACPI Sleep State

Options: Suspend Disabled / S1 only (CPU Stop Clock)

ü Lock Legacy Resources

Options: Enabled / Disabled

Beckhoff New Automation Technology CB3056 page 43

Chapter: BIOS Settings Advanced

4.3.3 CPU Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ CPU Configuration │Disabled for Windows XP │ │ │ │ │ Intel(R) Core(TM) i7-2710QE CPU @ 2.10GHz │ │ │ CPU Signature 206a7 │ │ │ Microcode Patch 25 │ │ │ Max CPU Speed 2100 MHz │ │ │ Min CPU Speed 800 MHz │ │ │ CPU Speed 2100 MHz │ │ │ Processor Cores 4 │ │ │ Intel HT Technology Supported │ │ │ Intel VT-x Technology Supported │ │ │ Intel SMX Technology Supported │ │ │ 64-bit Supported │ │ │ │ │ │ L1 Data Cache 32 kB x 4 │ │ │ L1 Code Cache 32 kB x 4 │────────────────────────────────│ │ L2 Cache 256 kB x 4 │→←: Select Screen │ │ L3 Cache 6144 kB │↑↓: Select Item │ │ │Enter: Select │ │ Hyper-threading [Enabled] │+/-: Change Opt. │ │ Active Processor Cores [All] │F1: General Help │ │ Limit CPUID Maximum [Disabled] │F2: Previous Values │ │ Execute Disable Bit [Enabled] │F3: Optimized Defaults │ │ Intel Virtualization Technology [Disabled] │F4: Save & Exit │ │ TCC Activation Offset 0 │ESC: Exit │ │ Primary Plane Current value 0 │ │ │ Secondary Plane Current value 0 │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü CPU Signature

Options: none

ü Microcode Patch

Options: none

ü Max CPU Speed

Options: none

ü Min CPU Speed

Options: none

ü CPU Speed

Options: none

ü Processor Cores

Options: none

ü Intel HT Technology

Options: none

ü Intel VT-x Technology

Options: none

ü Intel SMX Technology

Options: none

ü 64-bit

Options: none

ü L1 Data Cache

Options: none

page 44 Beckhoff New Automation Technology CB3056

Advanced Chapter: BIOS Settings ü L1 Code Cache

Options: none

ü L2 Cache

Options: none

ü L3 Cache

Options: none

ü Hyper-threading

Options: Enabled

ü Active Processor Cores

Options: All

ü Limit CPUID Maximum

Options: Enabled / Disabled

ü Execute Disable Bit

Options: Enabled / Disabled

ü Intel Virtualization Technology

Options: Enabled / Disabled

ü TCC Activation Offset

Options: 0...50

ü Primary Plane Current value

Options: 0...255

ü Secondary Plane Current value

Options: 0...255

Beckhoff New Automation Technology CB3056 page 45

Chapter: BIOS Settings Advanced

4.3.4 SATA Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ SATA Controller(s) [Enabled] ▲│Enable or disable SATA Device. │ │ SATA Mode Selection [RAID] █│ │ │ SATA Test Mode [Disabled] █│ │ │ Alternate ID [Disabled] █│ │ │ █│ │ │ Serial ATA Port 0 Empty █│ │ │ Software Preserve Unknown █│ │ │ Port 0 [Enabled] █│ │ │ Hot Plug [Enabled] █│ │ │ Spin Up Device [Disabled] █│ │ │ Serial ATA Port 1 Empty █│ │ │ Software Preserve Unknown █│ │ │ Port 1 [Enabled] █│────────────────────────────────│ │ Hot Plug [Enabled] █│→←: Select Screen │ │ Spin Up Device [Disabled] █│↑↓: Select Item n │ │ Serial ATA Port 2 Empty █│Enter: Select │ │ Software Preserve Unknown █│+/-: Change Opt. │ │ Port 2 [Enabled] █│F1: General Help │ │ Hot Plug [Disabled] █│F2: Previous Values │ │ External SATA [Disabled] █│F3: Optimized Defaults │ │ Hot Plug [Enabled] █│F4: Save & Exit │ │ Spin Up Device [Disabled] Drive] █│ESC: Exit │ │ Serial ATA Port 3 Empty █│ │ │ Software Preserve Unknown █│ │ │ Port 3 [Enabled] █│ │ │ Hot Plug [Enabled] ░│ │ │ External SATA [Disabled] ▼│ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü SATA Controller(s)

Options: Enabled / Disabled

ü SATA Mode Selection

Options: IDE / AHCI / RAID

ü SATA Test Mode

Options: Enabled / Disabled

ü Alternate ID

Options: Enabled / Disabled

ü Serial ATA Port X

Options: none

ü Software Preserve

Options: none

ü Port X

Options: Enabled / Disabled

ü Hot Plug

Options: Enabled / Disabled

ü Hot Plug

Options: Enabled / Disabled

ü Spin Up Device

Options: Enabled / Disabled

page 46 Beckhoff New Automation Technology CB3056

Advanced Chapter: BIOS Settings

4.3.5 Power Controller Options

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Bootloader Version 0.13-00 │Select Power line for external │ │ Firmware Version 0.17-20 │USB devices, if powered-down │ │ Mainboard Serial No 0948251130007 │ │ │ Mainboard Prod. Date (Week.Year) 28.12 │ │ │ Mainboard BootCount 128 │ │ │ Mainboard Operation Time 12090min (201h) │ │ │ Voltage (Min/Max) 4.60V / 5.20V │ │ │ Temperature (Min/Max) 18'C /51'C │ │ │ │ │ │ ext. USB-Port Voltage [Off in S3-5] │ │ │ int. USB-Port Voltage [Off in S3-5] │ │ │ │ │ │ WatchDogTimer Mode [Compatibility Mode] │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Bootloader Version

Options: none

ü Firmware Version

Options: none

ü Mainboard Serial No

Options: none

ü Mainboard Prod. Date (Week.Year)

Options: none

ü Boot Count

Options: none

ü Minute Meter

Options: none

ü Voltage (Min/Max)

Options: none

ü Temperature (Min/Max)

Options: none

ü ext. USB-Port Voltage

Options: Off in S3-5 / by SVCC

ü int. USB-Port Voltage

Options: Off in S3-5 / by SVCC

Beckhoff New Automation Technology CB3056 page 47

Chapter: BIOS Settings Advanced

ü WatchDogTimer Mode

Options: Normal Mode / Compatibility Mode

ü WDT OSBoot Timout

Options: Disabled / 45 Seconds ... 255 Seconds

page 48 Beckhoff New Automation Technology CB3056

Advanced Chapter: BIOS Settings

4.3.6 USB Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ USB Configuration │Enables Legacy USB support. │ │ │AUTO option disables legacy │ │ USB Devices: │support if no USB devices are │ │ 1 Drive, 1 Keyboard, 1 Mouse │connected. DISABLE option will │ │ │keep USB devices available │ │ Legacy USB Support [Auto] │only for EFI applications. │ │ EHCI Hand-off [Disabled] │ │ │ │ │ │ USB hardware delays and time-outs: │ │ │ USB transfer time-out [5 sec] │ │ │ Device reset time-out [10 sec] │ │ │ Device power-up delay [Auto] │ │ │ │────────────────────────────────│ │ Mass Storage Devices: │→←: Select Screen │ │ Corsair Flash Voyager 1100 [Auto] │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü USB Devices

Options: none

ü Legacy USB Support

Options: Enabled / Disabled / Auto

ü EHCI Hand-off

Options: Enabled / Disabled

ü USB transfer time-out

Options: 5 sec / 10 sec / 20 sec

ü Device reset time-out

Options: 10 sec / 20 sec / 30 sec / 40 sec

ü Device power-up delay

Options: Auto / Manual

ü Mass Storage Devices: [Device Name]

Options: Auto / Floppy / Forced FDD / Hard Disk / CD-ROM

Beckhoff New Automation Technology CB3056 page 49

Chapter: BIOS Settings Advanced

4.3.7 Super IO Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Super IO Configuration │Set Parameters of Serial Port │ │ │0 (COMA) │ │ Super IO Chip SMSC SCH3114 │ │ │► Serial Port 0 Configuration │ │ │► Serial Port 1 Configuration │ │ │► Serial Port 2 Configuration │ │ │► Serial Port 3 Configuration │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Super IO Chip

Options: none

ü Serial Port X Configuration

Sub menu: see "Serial Port Configuration" (p. 51)

page 50 Beckhoff New Automation Technology CB3056

Advanced Chapter: BIOS Settings

4.3.7.1 Serial Port Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Serial Port 0 Configuration │Enable or Disable Serial Port │ │ │(COM) │ │ Serial Port [Enabled] │ │ │ Device Settings IO=3F8h; IRQ=4; │ │ │ │ │ │ Change Settings [Auto] │ │ │ Device Mode [Normal] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Serial Port

Options: Enabled / Disabled

ü Device Settings

Options: none

ü Change Settings

Options: Auto / IO=3F8h; IRQ=4 / IO=3F8h; IRQ=3, ...12 / IO=2F8h; IRQ=3, ...12 / IO=3E8h;

IRQ=3, ...12 / IO=2E8h; IRQ=3, ...12

ü Device Mode

Options: Normal / High Speed

Beckhoff New Automation Technology CB3056 page 51

Chapter: BIOS Settings Advanced

4.3.8 H/W Monitor

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Pc Health Status │ │ │ │ │ │ CPU Temperature : +38'C │ │ │ Board Temperature : +25'C │ │ │ Memory Temperature : +40'C │ │ │ SYS FAN Speed : N/A │ │ │ CPU FAN Speed : N/A │ │ │ AUX FAN Speed : N/A │ │ │ +1.05V : +1.04 V │ │ │ VccCore : +1.07 V │ │ │ +3.3V : +3.33 V │ │ │ Vcc : +4.68 V │ │ │ +12V : +12.61 V │────────────────────────────────│ │ VTR : +3.31 V │→←: Select Screen │ │ Vbat : +0.13 V │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü CPU Temperature

Options: none

ü Board Temperature

Options: none

ü Memory Temperature

Options: none

ü SYS FAN Speed

Options: none

ü CPU FAN Speed

Options: none

ü AUX FAN Speed

Options: none

ü +1.05V

Options: none

ü VccCore

Options: none

ü +3.3V

Options: none

ü Vcc

Options: none

ü +12V

Options: none

page 52 Beckhoff New Automation Technology CB3056

Advanced Chapter: BIOS Settings ü VTR

Options: none

ü Vbat

Options: none

Beckhoff New Automation Technology CB3056 page 53

Chapter: BIOS Settings Advanced

4.3.9 Serial Port Console Redirection

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ │Console Redirection Enable or │ │ COM0 │Disable. │ │ Console Redirection [Enabled] │ │ │► Console Redirection Settings │ │ │ │ │ │ COM1 │ │ │ Console Redirection [Disabled] │ │ │► Console Redirection Settings │ │ │ │ │ │ COM2 │ │ │ Console Redirection [Disabled] │ │ │► Console Redirection Settings │ │ │ │────────────────────────────────│ │ COM3 │→←: Select Screen │ │ Console Redirection [Disabled] │↑↓: Select Item │ │► Console Redirection Settings │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Console Redirection

Options: Enabled / Disabled

ü Console Redirection Settings

Sub menu: see "Console Redirection Settings" (p. 55)

page 54 Beckhoff New Automation Technology CB3056

Advanced Chapter: BIOS Settings

4.3.9.1 Console Redirection Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ COM0 │Emulation: ANSI: Extended │ │ Console Redirection Settings │ASCII char set. VT100: ASCII │ │ │char set. VT100+: Extends │ │ Terminal Type [VT-UTF8] │VT100 to support color, │ │ Bits per second [115200] │function keys, etc. VT-UTF8: │ │ Data Bits [8] │Uses UTF8 encoding to map │ │ Parity [None] │Unicode chars onto 1 or more │ │ Stop Bits [1] │bytes. │ │ Flow Control [None] │ │ │ VT-UTF8 Combo Key Support [Enabled] │ │ │ Recorder Mode [Disabled] │ │ │ Resolution 100x31 [Enabled] │ │ │ Legacy OS Redirection Resolution [80x24] │────────────────────────────────│ │ Putty KeyPad [VT100] │→←: Select Screen │ │ Redirection After BIOS POST [Always Enable] │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Terminal Type

Options: VT100 / VT100+ / VT-UTF8 / ANSI

ü Bits per second

Options: 9600 / 19200 / 38400 / 57600 / 115200

ü Data Bits

Options: 7 / 8

ü Parity

Options: None / Even / Odd / Mark / Space

ü Stop Bits

Options: 1 / 2

ü Flow Control

Options: None / Hardware RTS/CTS

ü VT-UTF8 Combo Key Support

Options: Disabled / Enabled

ü Recorder Mode

Options: Disabled / Enabled

ü Resolution 100x31

Options: Disabled / Enabled

ü Legacy OS Redirection Resolution

Options: 80x24 / 80x25

ü Putty KeyPad

Options: VT100 / LINUX / XTERMR6 / SCO / ESCN / VT400

Beckhoff New Automation Technology CB3056 page 55

Chapter: BIOS Settings Advanced

4.3.10 CPU PPM Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ CPU PPM Configuration │Enable/Disable Intel SpeedStep │ │ │ │ │ EIST [Disabled] │ │ │ CPU Cx Report [C0] │ │ │ Config TDP Lock [Disabled] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü EIST

Options: Disabled / Enabled

ü CPU Cx Report

Options: C0 / C1 / C3 / C6 / C7

ü Config TDP LOCK

Options: Disabled / Enabled

page 56 Beckhoff New Automation Technology CB3056

Chipset Chapter: BIOS Settings

4.4 Chipset

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │► PCH-IO Configuration │System Agent (SA) Parameters │ │► System Agent (SA) Configuration │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü PCH-IO Configuration

Sub menu: see "PCH-IO Configuration" (p. 58)

ü System Agent (SA) Configuration

Sub menu: see "System Agent (SA) Configuration" (p. 65)

Beckhoff New Automation Technology CB3056 page 57

Chapter: BIOS Settings Chipset

4.4.1 PCH-IO Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Intel PCH RC Version 1.5.0.0 │Enable or disable onboard NIC. │ │ Intel PCH SKU Name QM67 │ │ │ Intel PCH Rev ID 05/B3 │ │ │ │ │ │► PCI Express Configuration │ │ │► USB Configuration │ │ │► PCH Azalia Configuration │ │ │ │ │ │ PCH LAN Controller [Enabled] │ │ │ LAN1 MAC address 00:01:05:11:29:F4 │ │ │ Wake on LAN [Enabled] │ │ │ Second LAN Controller [Enabled] │────────────────────────────────│ │ LAN2 MAC address 00:01:05:11:29:F5 │→←: Select Screen │ │ Board Capability [SUS_PWR_DN_ACK] │↑↓: Select Item │ │ Display Logic [Enabled] │Enter: Select │ │ CLKRUN# Logic [Disabled] │+/-: Change Opt. │ │ SB CRID [Disabled] │F1: General Help │ │ │F2: Previous Values │ │ High Precision Event Timer Configuration │F3: Optimized Defaults │ │ High Precision Timer [Enabled] │F4: Save & Exit │ │ │ESC: Exit │ │ Restore AC Power Loss [Power On] │ │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Intel PCH RC Version

Options: none

ü Intel PCH SKU Name

Options: none

ü Intel PCH Rev ID

Options: none

ü PCI Express Configuration

Sub menu: see "PCI Express Configuration" (p. 60)

ü USB Configuration

Sub menu: see "USB Configuration" (p. 63)

ü PCH Azalia Configuration

Sub menu: see "PCH Azalia Configuration" (p. 64)

ü PCH LAN Controller

Options: Disabled / Enabled

ü LAN1 MAC address

Options: none

ü Wake on LAN

Options: Disabled / Enabled

ü Second LAN Controller

Options: Disabled / Enabled

ü LAN2 MAC address

Options: none

page 58 Beckhoff New Automation Technology CB3056

Chipset Chapter: BIOS Settings ü Board Capability

Options: SUS_PWR_DN_ACK / DeepSx

ü Display Logic

Options: Disabled / Enabled

ü CLKRUN# Logic

Options: Disabled

ü SB CRID

Options: Disabled / Enabled

ü High Precision Timer

Options: Disabled / Enabled

ü Restore AC Power Loss

Options: Power Off / Power On / Last State

Beckhoff New Automation Technology CB3056 page 59

Chapter: BIOS Settings Chipset

4.4.1.1 PCI Express Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCI Express Configuration │Enable or disable PCI Express │ │ │Clock Gating for each root │ │ PCI Express Clock Gating [Enabled] │port. │ │ DMI Link ASPM Control [Enabled] │ │ │ DMI Link Extended Synch Control [Disabled] │ │ │ PCIe-USB Glitch W/A [Disabled] │ │ │ Subtractive Decode [Disabled] │ │ │ │ │ │ PCI Express Root Port 1 │ │ │► PCI Express Root Port 2 │ │ │► PCI Express Root Port 3 │ │ │► PCI Express Root Port 4 │ │ │ PCIE Port 5 is assigned to LAN │────────────────────────────────│ │ PCIE Port 6 is assigned to LAN2 │→←: Select Screen │ │► PCIE Port 7 is assigned to PCIe to PCI Bridge │↑↓: Select Item │ │► PCI Express Root Port 8 │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü PCI Express Clock Gating

Options: Disabled / Enabled

ü DMI Link ASPM Control

Options: Disabled / Enabled

ü DMI Link Extended Synch Control

Options: Disabled / Enabled

ü PCIe-USB Glitch W/A

Options: Disabled / Enabled

ü Subtractive Decode

Options: Disabled

ü PCI Express Root Port X

Sub menu: see "PCI Express Root Port" (p. 61)

page 60 Beckhoff New Automation Technology CB3056

Chipset Chapter: BIOS Settings

4.4.1.1.1 PCI Express Root Port

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCI Express Root Port 2 [Enabled] │Control the PCI Express Root │ │ ASPM Support [Auto] │Port. │ │ URR [Disabled] │ │ │ FER [Disabled] │ │ │ NFER [Disabled] │ │ │ CER [Disabled] │ │ │ CTO [Disabled] │ │ │ SEFE [Disabled] │ │ │ SENFE [Disabled] │ │ │ SECE [Disabled] │ │ │ PME SCI [Enabled] │ │ │ Hot Plug [Disabled] │ │ │ PCIe Speed [Auto] │────────────────────────────────│ │ Extra Bus Reserved 0 │→←: Select Screen │ │ Reserved Memory 10 │↑↓: Select Item │ │ Prefetchable Memory 10 │Enter: Select │ │ Reserved I/O 4 │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü PCI Express Root Port x

Options: Disabled / Enabled

ü ASPM Support

Options: Disabled / L0s / L1 / L0sL1 / Auto

ü URR

Options: Disabled / Enabled

ü FER

Options: Disabled / Enabled

ü NFER

Options: Disabled / Enabled

ü CER

Options: Disabled / Enabled

ü CTO

Options: Disabled / Enabled

ü SEFE

Options: Disabled / Enabled

ü SENFE

Options: Disabled / Enabled

ü SECE

Options: Disabled / Enabled

ü PME SCI

Options: Disabled / Enabled

Beckhoff New Automation Technology CB3056 page 61

Chapter: BIOS Settings Chipset ü Hot Plug

Options: Disabled / Enabled

ü PCIe Speed

Options: Auto / Gen1 / Gen2

ü Extra Bus Reserved

Options: 0...7

ü Reserved Memory

Options: 1...20

ü Prefetchable Memory

Options: 1...20

ü Reserved I/O

Options: 4 / 8 / 12 / 16 / 20

page 62 Beckhoff New Automation Technology CB3056

Chipset Chapter: BIOS Settings

4.4.1.2 USB Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ USB Configuration │Control the USB EHCI (USB 2.0) │ │ │functions. │ │ EHCI1 [Enabled] │One EHCI controller must │ │ EHCI2 [Enabled] │always be enabled. │ │ │ │ │ USB Ports Per-Port Disable Control [Disabled] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü EHCI1

Options: Disabled / Enabled

ü EHCI2

Options: Disabled / Enabled

ü USB Ports Per-Port Disable Control

Options: Disabled / Enabled

Beckhoff New Automation Technology CB3056 page 63

Chapter: BIOS Settings Chipset

4.4.1.3 PCH Azalia Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCH Azalia Configuration │Control Detection of the │ │ │Azalia device. │ │ Azalia [Auto] │Disabled = Azalia will be │ │ Azalia PME [Disabled] │unconditionally disabled │ │ Azalia Internal HDMI Codec [Disabled] │Enabled = Azalia will be │ │ │unconditionally Enabled │ │ │Auto = Azalia will be enabled │ │ │if present, disabled otherwise. │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Azalia

Options: Disabled / Enabled / Auto

ü Azalia PME

Options: Disabled / Enabled

ü Azalia Internal HDMI Codec

Options: Disabled / Enabled

page 64 Beckhoff New Automation Technology CB3056

Chipset Chapter: BIOS Settings

4.4.2 System Agent (SA) Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ System Agent Bridge Name SandyBridge │Check to enable VT-d function │ │ System Agent RC Version 1.5.0.0 │on MCH. │ │ │ │ │ VT-d [Disabled] │ │ │ CHAP Device (B0:D7:F0) [Disabled] │ │ │ Thermal Device (B0:D4:F0) [Disabled] │ │ │ Enable NB CRID [Disabled] │ │ │ BDAT ACPI Table Support [Disabled] │ │ │ │ │ │► Graphics Configuration │ │ │► NB PCIe Configuration │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü VT-d

Options: Disabled / Enabled

ü CHAP Device (B0:D7:F0)

Options: Disabled / Enabled

ü Thermal Device (B0:D4:F0)

Options: Disabled / Enabled

ü Enable NB CRID

Options: Disabled / Enabled

ü BDAT ACPI Table Support

Options: Disabled / Enabled

ü Graphics Configuration

Sub menu: see "Graphics Configuration" (p. 66)

ü NB PCIe Configuration

Sub menu: see "NB PCIe Configuration" (p. 68)

Beckhoff New Automation Technology CB3056 page 65

Chapter: BIOS Settings Chipset

4.4.2.1 Graphics Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Graphics Configuration │Graphics turbo IMON current │ │ IGFX VBIOS Version 2137 │values supported (14-31) │ │ IGfx Frequency 650 MHz │ │ │ Graphics Turbo IMON Current 31 │ │ │ │ │ │ Primary Display [Auto] │ │ │ Internal Graphics [Auto] │ │ │ GTT Size [2MB] │ │ │ Aperture Size [256MB] │ │ │ DVMT Pre-Allocated [64M] │ │ │ DVMT Total Gfx Mem [256M] │ │ │ Gfx Low Power Mode [Disabled] │ │ │► LCD Control │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü IGFX VBIOS Version

Options: none

ü IGFX Frequency

Options: none

ü Graphics Turbo IMON Current

Options: 14...31

ü Primary Display

Options: Auto / IGFX / PEG / PCI

ü Internal Graphics

Options: Auto / Disabled / Enabled

ü GTT Size

Options: 1MB / 2MB

ü Aperture Size

Options: 128MB / 256MB / 512MB

ü DVMT Pre-Allocated

Options: 32M / 64M ... 480M / 512M / 1024M

ü DVMT Total Gfx Mem

Options: 128M / 256M / MAX

ü Gfx Low Power Mode

Options: Disabled / Enabled

ü LCD Control

Sub menu: see "LCD Control" (p. 67)

page 66 Beckhoff New Automation Technology CB3056

Chipset Chapter: BIOS Settings

4.4.2.1.1 LCD Control

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ LCD Control │Select the Video Device which │ │ │will be activated during POST. │ │ Primary IGFX Boot Display [VBIOS Default] │This has no effect if external │ │ LCD Panel Type [1024x768 LVDS] │graphics present. │ │ Spread Spectrum clock Chip [Off] │Secondary boot display │ │ ALS Support [Disabled] │selection will appear based on │ │ │your selection. │ │ │VGA modes will be supported │ │ │only on primary display │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Primary IGFX Boot Display

Options: VBIOS Default / CRT / EFP / LFP / EFP3 / EFP2 / LFP2

ü LCD Panel Type

Options: VBIOS Default / 640x480 LVDS ...1920x1080 LVDS / 2048x1536 LVDS

ü Spread Spectrum Clock Chip

Options: Off / Hardware / Software

ü ALS Support

Options: Disabled / Enabled

Beckhoff New Automation Technology CB3056 page 67

Chapter: BIOS Settings Chipset

4.4.2.2 NB PCIe Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ NB PCIe Configuration │Configure PEG0 B0:D1:F0 │ │ PEG0 Not Present │Gen1-Gen3 │ │ PEG0 - Gen X [Auto] │ │ │ PEG0 ASPM [Auto] │ │ │ │ │ │ Enable PEG [Auto] │ │ │ De-emphasis Control [-3.5 dB] │ │ │ PEG Sampler Calibrate [Auto] │ │ │ Swing Control [Full] │ │ │ Gen3 Equalization [Disabled] │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü PEGn - Gen X

Options: Auto / Gen1 / Gen2 / Gen3

ü PEGn ASPM

Options: Disabled / Auto / ASPM L0s / ASPM L1 / ASPM L0sL1

ü Enable PEG

Options: Disabled / Enabled / Auto

ü De-emphasis Control

Options: -6 dB / -3.5 dB

ü PEG Sampler Calibrate

Options: Auto / Disabled / Enabled

ü Swing Control

Options: Reduced / Half / Full

ü Gen3 Equalization

Options: Disabled / Enabled

page 68 Beckhoff New Automation Technology CB3056

Boot Chapter: BIOS Settings

4.5 Boot

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Boot Configuration │Number of 1/10 sec. to wait │ │ Setup Prompt Timeout 5 │for setup activation key. 0 │ │ Bootup NumLock State [On] │means no wait. │ │ │ │ │ Full Screen Logo [Enabled] │ │ │ Fast Boot [Disabled] │ │ │ │ │ │ CSM16 Module Version 07.69 │ │ │ │ │ │ GateA20 Active [Upon Request] │ │ │ INT19 Trap Request [Postponed] │ │ │ Servicestick priority [Disabled] │ │ │ │────────────────────────────────│ │ Boot Option Priorities │→←: Select Screen │ │ Boot Option #1 [P4: ExcelStor Tech...] │↑↓: Select Item │ │ Boot Option #2 [IBA GE Slot 00C8 v...] │Enter: Select │ │► CSM Parameters │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Setup Prompt Timeout

Options: 0...65535 [x 1/10 sec.]

ü Bootup NumLock State

Options: On / Off

ü Full Screen Logo

Options: Disabled / Enabled

ü Fast Boot

Options: Disabled / Enabled

ü Skip VGA

Options: Disabled / Enabled

ü Skip USB

Options: Disabled / Enabled

ü Skip PS2

Options: Disabled / Enabled

ü CSM16 Module Version

Options: none

ü GateA20 Active

Options: Upon Request / Always

ü ING19 Trap Response

Options: Immediate / Postponed

ü Servicestick priority

Options: Disabled / Enabled

Beckhoff New Automation Technology CB3056 page 69

Chapter: BIOS Settings Boot ü Boot Option Priorities

Options: Review or change the sequence of available boot devices

ü CSM Parameters

Sub menu: see "CSM Parameters" (p. 71)

page 70 Beckhoff New Automation Technology CB3056

Boot Chapter: BIOS Settings

4.5.1 CSM Parameters

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Boot option filter [Legacy only] │System Agent (SA) Parameters │ │ Launch PXE OpROM policy [Enable] │ │ │ │ │ │ Other PCI device ROM priority [Legacy OpROM] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Boot option filter

Options: UEFI and Legacy / Legacy only / UEFI only

ü Launch PXE OpROM policy

Options: Disable / Enable

ü Other PCI device ROM priority

Options: UEFI OpROM / Legacy OpROM

Beckhoff New Automation Technology CB3056 page 71

Chapter: BIOS Settings Security

4.6 Security

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ The password length must be │Set Administrator Password. │ │ in the following range: │When set, this password has to │ │ Minimum length 3 │be entered to enter setup │ │ Maximum length 20 │ │ │ │ │ │ Administrator Password │ │ │ │ │ │ UEFI Secure Boot Management │ │ │ Secure Boot control [Enabled] │ │ │► Secure Boot Policy │ │ │► Key Management │ │ │ │ │ │ HDD Security Configuration: │────────────────────────────────│ │ P4:ExcelStor Te │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Administrator Password

Options: Press [Enter]

ü Secure Boot control

Options: Disabled / Enabled

ü Secure Boot Policy

Sub menu: see "Secure Boot Policy" (p. 73)

ü Key Management

Sub menu: see "Key Management" (p. 74)

ü HDD Security Configuration:

Options: Set user password for attached hard disk

page 72 Beckhoff New Automation Technology CB3056

Security Chapter: BIOS Settings

4.6.1 Secure Boot Policy

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Internal RV [Always Execute] │Image Execution Policy on │ │ Option ROM [Deny Execute] │Security Violation. Image load │ │ Removable Media [Deny Execute] │device path │ │ Fixed Media [Deny Execute] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Internal FV

Options: Always Execute

ü Option ROM

Options: Always Execute / Always Deny / Allow Execute / Defer Execute / Deny Execute / Query

User

ü Removable Media

Options: Always Execute / Always Deny / Allow Execute / Defer Execute / Deny Execute / Query

User

ü Fixed Media

Options: Always Execute / Always Deny / Allow Execute / Defer Execute / Deny Execute / Query

User

Beckhoff New Automation Technology CB3056 page 73

Chapter: BIOS Settings Security

4.6.2 Key Management

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ System Mode Setup │Launches the Filebrowser to │ │ Secure Boot Mode Disabled │set the Platform Key from file │ │ │ │ │ Platform Key (PK) NOT INSTALLED │ │ │► Set PK from File │ │ │► Get PK to File │ │ │► Delete the PK │ │ │ Key Exchange Key Database(KEK) NOT INSTALLED │ │ │► Set KEK from File │ │ │► Get KEK to File │ │ │► Delete the KEK │ │ │► Append an entry to KEK │ │ │ Authorized Signature Database(DB) NOT INSTALLED │────────────────────────────────│ │► Set DB from File │→←: Select Screen │ │► Get DB to File │↑↓: Select Item │ │► Delete the DB │Enter: Select │ │► Append an entry to DB │+/-: Change Opt. │ │ Forbidden Signature Database(DBX) NOT INSTALLED │F1: General Help │ │► Set DBX from File │F2: Previous Values │ │► Get DBX to File │F3: Optimized Defaults │ │► Delete the DBX │F4: Save & Exit │ │► Append an entry to DBX │ESC: Exit │ │ │ │ │ Manage All Factory Keys (PK,KEK,DB,DBX) │ │ │ Install Factory Defaults │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü System Mode

Options: none

ü Secure Boot Mode

Options: none

ü Set PK from File

Options: Press [Enter]

ü Get PK to File

Options: Press [Enter]

ü Delete the PK

Options: Press [Enter]

ü Set KEK from File

Options: Press [Enter]

ü Get KEK to File

Options: Press [Enter]

ü Delete the KEK

Options: Press [Enter]

ü Append an entry to KEK

Options: Press [Enter]

ü Set DB from File

Options: Press [Enter]

ü Get DB to File

Options: Press [Enter]

page 74 Beckhoff New Automation Technology CB3056

Security Chapter: BIOS Settings ü Delete the DB

Options: Press [Enter]

ü Append an entry to DB

Options: Press [Enter]

ü Set DBX from File

Options: Press [Enter]

ü Get DBX to File

Options: Press [Enter]

ü Delete the DBX

Options: Press [Enter]

ü Append an entry to DBX

Options: Press [Enter]

ü Install Factory Defaults

Options: Press [Enter]

Beckhoff New Automation Technology CB3056 page 75

Chapter: BIOS Settings Save & Exit

4.7 Save & Exit

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Save Changes and Reset │Reset the system after saving │ │ Discard Changes and Reset │the changes. │ │ │ │ │ Restore Defaults │ │ │ Save as User Defaults │ │ │ Restore User Defaults │ │ │ │ │ │ Boot Override │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

ü Save Changes and Reset

Options: Press [Enter]

ü Discard Changes and Reset

Options: Press [Enter]

ü Restore Defaults

Options: Press [Enter]

ü Save as User Defaults

Options: Press [Enter]

ü Restore User Defaults

Options: Press [Enter]

ü Boot Override

Options: Press [Enter]

page 76 Beckhoff New Automation Technology CB3056

BIOS update Chapter: BIOS Settings

4.8 BIOS update

If a BIOS update becomes necessary, the program “AFUDOS.EXE” from AMI® is used for this. It is important, that the program is started from a DOS environment without a virtual memory manager such as for example “EMM386.EXE”. In case such a memory manager is loaded, the program will stop with an error message. The system must not be interrupted during the flash process, otherwise the update is stopped and the BIOS is destroyed afterwards. The program should be started as follows:

afudos [romfile] /p /b /n

/p Program BIOS file /b Program boot block /n Program NVRAM

CAUTION

Updating the BIOS in an improper way can render the board unusable. Therefore, you should only update the BIOS if you really need the changes/corrections which come with the new BIOS version.

CAUTION

Before you proceed to update the BIOS you need to make absolutely sure that you have the right BIOS file which was issued for the exact board and exact board revision that you wish to update. If you try to update the BIOS using the wrong file the board will not start up again.

Beckhoff New Automation Technology CB3056 page 77

Chapter: Mechanical Drawings PCB: Mounting Holes

5 Mechanical Drawings

5.1 PCB: Mounting Holes

A true dimensioned drawing can be found in the PC/104 specification.

NOTE

All dimensions are in mil (1 mil = 0,0254 mm)

page 78 Beckhoff New Automation Technology CB3056

PCB: Pin 1 Dimensions Chapter: Mechanical Drawings

5.2 PCB: Pin 1 Dimensions

NOTE

All dimensions are in mil (1 mil = 0,0254 mm)

Beckhoff New Automation Technology CB3056 page 79

Chapter: Mechanical Drawings PCB: Die Center

5.3 PCB: Die Center

NOTE

All dimensions are in mil (1 mil = 0,0254 mm)

page 80 Beckhoff New Automation Technology CB3056

Electrical Data Chapter: Technical Data

6 Technical Data

6.1 Electrical Data

Power Supply:

Board: 5 Volt +/- 5% (5 Volt Suspend / 12 Volt Fan) RTC: >= 3 Volt

Electric Power Consumption:

Board: tbd RTC: <= 10µA

6.2 Environmental Conditions

Temperature Range:

Operating: 0°C to +60°C (extended temperature on request) Storage: -25°C up to +85°C Shipping: -25°C up to +85°C, for packaged boards

Temperature Changes:

Operating: 0.5°C per minute, 7.5°C per 30 minutes Storage: 1.0°C per minute Shipping: 1.0°C per minute, for packaged boards

Relative Humidity:

Operating: 5% up to 85% (non condensing) Storage: 5% up to 95% (non condensing) Shipping: 5% up to 100% (non condensing), for packaged boards

Shock:

Operating: 150m/s2, 6ms Storage: 400m/s2, 6ms Shipping: 400m/s2, 6ms, for packaged boards

Vibration:

Operating: 10 up to 58Hz, 0.075mm amplitude 58 up to 500Hz, 10m/s2 Storage: 5 up to 9Hz, 3.5mm amplitude 9 up to 500Hz, 10m/s2 Shipping: 5 up to 9Hz, 3.5mm amplitude 9 up to 500Hz, 10m/s2, for packaged boards

CAUTION

Shock and vibration figures pertain to the motherboard alone and do not include additional components such as heat sinks, memory modules, cables etc.

Beckhoff New Automation Technology CB3056 page 81

Chapter: Technical Data Thermal Specifications

6.3 Thermal Specifications

The board is specified to operate in an environmental temperature range from 0°C to +60°C (extended temperature on request). Maximum die temperature is 100°C. To keep the processor under this threshold an appropriate cooling solution needs to be applied. This solution has to take typical and maximum power consumption into account. The maximum power consumption may be twice as high and should be used as a basis for the cooling concept. Additional controllers may also affect the cooling concept. The power consumption of such components may be comparable to the consumption of the processor. The board design includes thermal solution mounting points that will provide the best possible thermal interface between die and solution. Since we take thermal solutions seriously we have several advanced, aggressive cooling solutions in our product portfolio. Please contact your sales representative to order or discuss your thermal solution needs.

CAUTION

The end customer has the responsibility to ensure that the die temperature of the processor does not exceed 100°C. Permanent overheating may destroy the board! In case the temperature exceeds 100°C the environmental temperature must be reduced. Under certain circumstances sufficient air circulation must be provided.

page 82 Beckhoff New Automation Technology CB3056

Beckhoff's Branch Offices and Representatives Chapter: Support and Service

7 Support and Service

Beckhoff and their partners around the world offer comprehensive support and service, making available fast and competent assistance with all questions related to Beckhoff products and system solutions.

7.1 Beckhoff's Branch Offices and Representatives

Please contact your Beckhoff branch office or representative for local support and service on Beckhoff products. The addresses of Beckhoff's branch offices and representatives around the world can be found on her internet pages: http://www.beckhoff.com You will also find further documentation for Beckhoff components there.

7.2 Beckhoff Headquarters

Beckhoff Automation GmbH Eiserstr. 5 33415 Verl Germany

phone: +49(0)5246/963-0 fax: +49(0)5246/963-198 e-mail: info@beckhoff.com web: www.beckhoff.com

7.2.1 Beckhoff Support

Support offers you comprehensive technical assistance, helping you not only with the application of individual Beckhoff products, but also with other, wide-ranging services:

o support o design, programming and commissioning of complex automation systems o and extensive training programs for Beckhoff system components

hotline: +49(0)5246/963-157 fax: +49(0)5246/963-9157 e-mail: support@beckhoff.com

7.2.2 Beckhoff Service

The Beckhoff Service Center supports you in all matters of after-sales service:

o on-site service o repair service o spare parts service o hotline service

hotline: +49(0)5246/963-460 fax: +49(0)5246/963-479 e-mail: service@beckhoff.com

Beckhoff New Automation Technology CB3056 page 83

Annex: Post-Codes

I Annex: Post-Codes

During boot, the BIOS generates a sequence of status codes (so-called "POST codes"), which can be viewed using a special output device (POST code card). The meaning of these codes is described in the document "Aptio™ 4.x Status Codes" by American Megatrends®, which can be downloaded from their website http://www.ami.com. The following additional OEM POST codes are generated:

Code Description

87h BIOS-API started 88h PCA9535 started 89h PWRCTRL-Firmware started

page 84 Beckhoff New Automation Technology CB3056

Annex: Resources

II Annex: Resources

IO Range

The used resources depend on setup settings. The given values are ranges, which are fixed by AT compatibility. Other IO ranges are used, which are dynamically adjusted by Plug & Play BIOS while booting.

Address Function

0-FF Reserved IO area of the board 170-17F 1F0-1F7 278-27F 2E8-2EF COM4 2F8-2FF COM2 370-377 378-37F 3BC-3BF 3E8-3EF COM3 3F0-3F7 3F8-3FF COM1

Memory Range

The used resources depend on setup settings. If the entire range is clogged through option ROMs, these functions do not work anymore.

Address Function

A0000-BFFFF VGA RAM C0000-CFFFF VGA BIOS D0000-E7FFF AHCI BIOS / RAID / PXE (if available) E8000-FFFFF System BIOS

Interrupt

The used resources depend on setup settings. The listed interrupts and their use are given through AT compatibility. If interrupts must exclusively be available on the ISA side, they have to be reserved through the BIOS setup. The exclusivity is not given and not possible on the PCI side.

Address Function

IRQ0 Timer IRQ1 PS/2 Keyboard IRQ2 (9) COM3 IRQ3 COM1 IRQ4 COM2 IRQ5 COM4 IRQ6 IRQ7 IRQ8 RTC IRQ9 IRQ10 IRQ11 IRQ12 PS/2 Mouse

Beckhoff New Automation Technology CB3056 page 85

Annex: Resources

Address Function

IRQ13 FPU IRQ14 IRQ15

PCI Devices

All listed PCI devices exist on the board. Some PCI devices or functions of devices may be disabled in the BIOS setup. Once a device is disabled other devices may get PCI bus numbers different from the ones listed in the table.

AD INTA REQ Bus Dev. Fct. Controller / Slot

- - 0 0 0 Host Bridge ID0104h A - 0 2 0 VGA Graphics ID0116h A - 0 25 0 LAN QM67 ID1502h A - 0 26 0 USB EHCI Controller #2 QM67 ID1C2Dh A - 0 27 0 HDA Controller QM67 ID1C20h A - 0 28 0 PCI Express Port 1 QM67 ID1C10h B - 0 28 1 [PCI Express Port 2 QM67 ID1C12h] C - 0 28 2 [PCI Express Port 3 QM67 ID1C14h] D - 0 28 3 [PCI Express Port 4 QM67 ID1C16h] A - 0 28 4 PCI Express Port 5 QM67 ID1C18h B - 0 28 5 PCI Express Port 6 QM67 ID1C1Ah C - 0 28 6 PCI Express Port 7 QM67 ID1C1Ch D - 0 28 7 [PCI Express Port 8 QM67 ID1C1Eh] A - 0 29 0 USB EHCI Controller #1 QM76 ID1C26h

- - 0 31 0 ISA Bridge QM67 ID1C4Fh B - 0 31 2 SATA Interface #1 QM67 ID1C01h B - 0 31 3 SMBus Interface QM67 ID1C22h B - 0 31 5 SATA Interface #2 QM67 ID1C09h A - m 0 0 LAN 82547L ID10D3h A - n 0 0 PCIe-to-PCI Bridge IDE111h 20 A 0 o 4 0 mPCI Slot 1

SMB Devices

The following table contains all reserved SM-Bus device addresses in 8-bit notation. Note that external devices must not use any of these addresses even if the component mentioned in the table is not present on the motherboard.

Address Function

10-11 Standard slave address 40-41 GPIO 60-61 BIOS internal 70-73 POST code output 88-89 BIOS-defined slave address A0-A1 DIMM 1 A2-A3 DIMM 2 A4-AF BIOS internal B0-BF BIOS internal D2-D3 Clock

page 86 Beckhoff New Automation Technology CB3056

BECKHOFF CB3056 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Contents

0 Document History

1 Introduction

1.1 Notes on the Documentation

1.2 Safety Instructions

1.3 Essential Safety Measures

1.4 Functional Range

2 Overview

2.1 Features

2.2 Specifications and Documents

3 Connectors

3.1 Connector Map

3.2 CPU Socket

3.3 Power Supply

3.4 System

3.5 Memory

3.6 VGA/DVI

3.7 DVI/HDMI/DisplayPort

3.8 USB 1-4

3.9 USB 5-10

3.10 LAN

3.11 Audio

3.12 SATA Interfaces

3.13 Serial Interface COM1

3.14 Serial Ports COM2 through COM4

3.15 PCI-Express

3.16 Mini-PCI

3.17 GPIO

3.18 Fan Connectors

4 BIOS Settings

4.1 General Remarks

4.2 Main

4.3 Advanced

4.4 Chipset

4.5 Boot

4.6 Security

4.7 Save & Exit

4.8 BIOS update

5 Mechanical Drawings

5.1 PCB: Mounting Holes

5.2 PCB: Pin 1 Dimensions

5.3 PCB: Die Center

6 Technical Data

6.1 Electrical Data

6.2 Environmental Conditions

6.3 Thermal Specifications

7 Support and Service

7.1 Beckhoff's Branch Offices and Representatives

7.2 Beckhoff Headquarters

I Annex: Post-Codes

II Annex: Resources

IO Range

Memory Range

Interrupt

PCI Devices

SMB Devices