Beckhoff CB1064 Manual 1.2

CB1064-xxxx

Manual

Rev. 1.2

Beckhoff Automation GmbH & Co. KG phone: +49 (0) 52 46/963-0 Eiserstr. 5 fax: +49 (0) 52 46/963-198 33415 Verl email: info@beckhoff.de Germany web: www.beckhoff.de

Contents

0 Document History................................................................................................................................. 7

1 Introduction .......................................................................................................................................... 8

1.1 Notes on the Documentation ........................................................................................................ 8

1.1.1 Disclaimer ............................................................................................................................. 8

1.1.2 Trademarks ........................................................................................................................... 8

1.1.3 Patent Pending ..................................................................................................................... 8

1.1.4 Copyright ............................................................................................................................... 8

1.2 Safety Instructions ........................................................................................................................ 9

1.2.1 Disclaimer ............................................................................................................................. 9

1.2.2 Description of Safety Symbols ............................................................................................ 10

1.3 FCC Approvals for the United States of America ....................................................................... 10

1.4 FCC Approval for Canada .......................................................................................................... 10

1.5 Essential Safety Measures ......................................................................................................... 11

1.5.1 Operator's Obligation to Exercise Diligence ....................................................................... 11

1.5.2 National Regulations Depending on the Machine Type ..................................................... 11

1.5.3 Operator Requirements ...................................................................................................... 11

1.6 Functional Range ........................................................................................................................ 12

2 Overview ............................................................................................................................................ 13

2.1 Features ...................................................................................................................................... 13

2.2 Feature List ................................................................................................................................. 14

2.3 Specifications and Documents ................................................................................................... 15

3 Connectors ......................................................................................................................................... 16

3.1 Power Supply, System Connectors, CPU .................................................................................. 17

3.1.1 Power Supply ...................................................................................................................... 17

3.1.2 System ................................................................................................................................ 19

3.1.3 CPU Socket ........................................................................................................................ 20

3.1.4 CMOS Battery ..................................................................................................................... 21

3.2 Back Panel Connectors .............................................................................................................. 22

3.2.1 DVI Connectors................................................................................................................... 22

3.2.2 DVI/HDMI ............................................................................................................................ 24

3.2.3 Display Port ......................................................................................................................... 25

3.2.4 PS/2 Keyboard and Mouse ................................................................................................. 26

3.2.5 Serial Port COM1 ................................................................................................................ 27

3.2.6 USB and LAN...................................................................................................................... 28

3.2.7 Audio Connectors ............................................................................................................... 30

3.3 SATA and Memory ..................................................................................................................... 31

3.3.1 SATA Interfaces .................................................................................................................. 31

3.3.2 Memory ............................................................................................................................... 32

3.4 Internal Connectors .................................................................................................................... 35

3.4.1 USB 2.0 ............................................................................................................................... 35

3.4.2 Serial ports COM2 to COM4 ............................................................................................... 36

3.4.3 CD-In ................................................................................................................................... 37

3.4.4 S/PDIF ................................................................................................................................ 38

3.4.5 PCI Interfaces ..................................................................................................................... 39

3.4.6 PCI-express Interfaces (x1) ................................................................................................ 41

3.4.7 PCI-express Interfaces (x4) ................................................................................................ 42

Beckhoff New Automation Technology CB1064-xxxx page 3

Contents

3.4.8 PCI-express Interface (x16) ................................................................................................ 44

3.4.9 SMB/I2C .............................................................................................................................. 46

3.4.10 GPIO ................................................................................................................................... 47

3.4.11 Fan Connectors .................................................................................................................. 48

3.5 Jumper Settings .......................................................................................................................... 49

3.5.1 Clear CMOS ........................................................................................................................ 49

3.5.2 Jumper: Keyboard Power (KBPWR)................................................................................... 50

4 BIOS-Einstellungen ............................................................................................................................ 51

4.1 General Remarks ........................................................................................................................ 51

4.2 Main ............................................................................................................................................ 52

4.3 Advanced .................................................................................................................................... 54

4.3.1 Platform Misc Configuration Configuration ......................................................................... 56

4.3.2 CPU Configuration .............................................................................................................. 60

4.3.3 Intel(R) I210 Gigabit Network Connection .......................................................................... 64

4.3.4 Intel(R) Ethernet Connection I219-LM ................................................................................ 66

4.3.5 Driver Health ....................................................................................................................... 67

4.3.6 Trusted Computing ............................................................................................................. 70

4.3.7 ACPI Settings...................................................................................................................... 71

4.3.8 SCH3114 Super IO Configuration ...................................................................................... 72

4.3.9 H/W Monitor ........................................................................................................................ 74

4.3.10 Serial Port Console Redirection.......................................................................................... 76

4.3.11 PCI Subsystem Settings ..................................................................................................... 79

4.3.12 Network Stack Configuration .............................................................................................. 81

4.3.13 Power Controller Options .................................................................................................... 82

4.3.14 Compatibility Support Module Configuration ...................................................................... 84

4.3.15 NVMe Controller and Drive Information .............................................................................. 85

4.3.16 USB Configuration .............................................................................................................. 86

4.3.17 SATA and RST Configuration ............................................................................................. 87

4.3.18 AMT Configuration .............................................................................................................. 91

4.4 Chipset ........................................................................................................................................ 97

4.4.1 System Agent (SA) Configuration ....................................................................................... 98

4.4.2 PCH-IO Configuration ....................................................................................................... 110

4.5 Security ..................................................................................................................................... 120

4.5.1 Secure Boot Menu ............................................................................................................ 121

4.6 Boot ........................................................................................................................................... 123

4.6.1 Fixed Boot Order Priority .................................................................................................. 125

4.7 Save & Exit ............................................................................................................................... 126

4.8 BIOS Update ............................................................................................................................. 127

5 Mechanical Drawings ....................................................................................................................... 128

5.1 PCB: Mounting Holes ............................................................................................................... 128

5.2 PCB: Dimensions ...................................................................................................................... 129

6 Technical Data ................................................................................................................................. 130

6.1 Electrical Data ........................................................................................................................... 130

6.2 Environmental Conditions ......................................................................................................... 130

6.3 Thermal Specifications ............................................................................................................. 131

7 Support and Service ........................................................................................................................ 132

7.1 Beckhoff's Branch Offices and Representatives ...................................................................... 132

7.2 Beckhoff Support ...................................................................................................................... 132

page 4 Beckhoff New Automation Technology CB1064-xxxx

Contents

7.3 Beckhoff Service ....................................................................................................................... 132

7.4 Beckhoff Headquarters ............................................................................................................. 132

I Annex: Post-Codes .......................................................................................................................... 134

II Annex: Resources ............................................................................................................................ 135

Interrupt ................................................................................................................................................ 135

PCI Devices .......................................................................................................................................... 135

Ressourcen: SMB-Devices .................................................................................................................. 136

Beckhoff New Automation Technology CB1064-xxxx page 5

Chapter: Document History Notes on the Documentation

page 6 Beckhoff New Automation Technology CB1064-xxxx

Notes on the Documentation Chapter: Document History

Version

Changes

0.1

first pre-release

1.0

first released version

1.1

Annex II: added SMB table

1.2

Updated mechanical drawings

0 Document History

All company names, brand names, and product names referred to in this manual are registered or unregistered trademarks of their respective holders and are, as such, protected by national and international law.

Beckhoff New Automation Technology CB1064-xxxx page 7

Chapter: Introduction Notes on the Documentation

1 Introduction

1.1 Notes on the Documentation

This description is only intended for the use of trained specialists in control and automation engineering who are familiar with the applicable national standards.

It is essential that the documentation and the following notes and explanations are followed when installing and commissioning the components.

It is the duty of the technical personnel to use the documentation published at the respective time of each installation and commissioning.

The responsible staff must ensure that the application or use of the products described satisfy all the requirements for safety, including all the relevant laws, regulations, guidelines and standards.

1.1.1 Disclaimer

The documentation has been prepared with care. The products described are, however, constantly under development.

For that reason the documentation is not in every case checked for consistency with performance data, standards or other characteristics.

None of the statements of this manual represents a guarantee (Garantie) in the meaning of § 443 BGB of the German Civil Code or a statement about the contractually expected fitness for a particular purpose in the meaning of § 434 par. 1 sentence 1 BGB.

In the event that it contains technical or editorial errors, we retain the right to make alterations at any time and without warning.

No claims for the modification of products that have already been supplied may be made on the basis of the data, diagrams and descriptions in this documentation.

1.1.2 Trademarks

Beckhoff®, TwinCAT®, EtherCAT®, Safety over EtherCAT®, TwinSAFE®, XFC® and XTS® are registered trademarks and licensed by Beckhoff Automation GmbH & Co. KG.

Other designations used in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owners.

1.1.3 Patent Pending

The EtherCAT Technology is covered, including but not limited to the following patent applications and patents:

EP1590927, EP1789857, DE 102004044764, DE 102007017835 with corresponding applications or registrations in various other countries. The TwinCAT Technology is covered, including but not limited to the following patent applications and

patents: EP0851348, US6167425 with corresponding applications or registrations in various other countries.. EtherCAT® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH &

Co. KG,Germany.

1.1.4 Copyright

patent, utility model or design.

page 8 Beckhoff New Automation Technology CB1064-xxxx

Safety Instructions Chapter: Introduction

1.2 Safety Instructions

Consider the following safety instructions and descriptions! Product specific safety instructions are to be found on the following pages or in the areas mounting,

wiring, commissioning etc.

1.2.1 Disclaimer

All the components are supplied in particular hardware and software configurations appropriate for the application. Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.

Beckhoff New Automation Technology CB1064-xxxx page 9

Chapter: Introduction FCC Approvals for the United States of America

DANGER

Acute risk of injury!

If you do not adhere the safety advise adjoining this symbol, there is immediate danger to life and health of individuals!

WARNING

Risk of injury!

If you do not adhere the safety advise adjoining this symbol, there is danger to life and health of individuals!

CAUTION

Hazard to devices and environment

If you do not adhere the safety advise adjoining this symbol, there is obvious hazard to individuals!

Attention

Hazard to devices and environment

If you do not adhere the notice adjoining this symbol, there is obvious hazard to materials and environment.

Notice

Note or pointer

This symbol indicates information that contributes to better understanding.

1.2.2 Description of Safety Symbols

The following safety symbols are used in this documentation. You have to read the safety symbols carefully and adhere them strictly!

1.3 FCC Approvals for the United States of America

FCC: Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

1.4 FCC Approval for Canada

FCC: Canadian Notice This equipment does not exceed the Class A limits for radiated emissions as described in the Radio

Interference Regulations of the Canadian Department of Communications.

page 10 Beckhoff New Automation Technology CB1064-xxxx

Essential Safety Measures Chapter: Introduction

1.5 Essential Safety Measures

1.5.1 Operator's Obligation to Exercise Diligence

The operator must ensure that

o the product is only used for its intended purpose o the product is only operated in sound condition and in working order o the instruction manual is in good condition and complete, and always available for reference at the

location where the products are used

o the product is only used by suitably qualified and authorised personnel o the personnel is instructed regularly about relevant occupational safety and environmental protection

aspects

o the operating personnel is familiar with the operating manual and in particular the safety notes

contained herein

1.5.2 National Regulations Depending on the Machine Type

Depending on the type of machine and plant in which the product is used, national regulations governing the controllers of such machines will apply, and must be observed by the operator. These regulations cover, amongst other things, the intervals between inspections of the controller. The operator must initiate such inspections in good time.

1.5.3 Operator Requirements

o Read the operating instructions All users of the product must have read the operating instructions for the system they work with. o System know-how All users must be familiar with all accessible functions of the product.

Beckhoff New Automation Technology CB1064-xxxx page 11

Chapter: Introduction Functional Range

1.6 Functional Range

The descriptions contained in the present documentation represent a detailed and extensive product description. As far as the described motherboard was acquired as an integral component of an Industrial PC from Beckhoff Automation GmbH & Co. KG, this product description shall be applied only in limited scope. Only the contractually agreed specifications of the corresponding Industrial PC from Beckhoff Automation GmbH & Co. KG shall be relevant. Due to several models of Industrial PCs, variations in the component placement of the motherboards are possible. Support and service benefits for the built-in motherboard will be rendered by Beckhoff Automation GmbH & Co. KG exclusively as specified in the product description (inclusive operation system) of the particular Industrial PC.

page 12 Beckhoff New Automation Technology CB1064-xxxx

Features Chapter: Overview

Intel® Q170 PCH

4x SoDIMM260

DDR4-2133

(dual channel)

MEMORY

Power VCCCore; VTT;

DDRVTT, GFXVCC

BIOS

SATA0-5

RealTek®

ALC888

HDA Link

DP

1.5/3/6GB

MAC/PHY

Intel®

i210

SMBus

SPI

SMSC®

SCH3114

LINE i/o

CD IN

MIC

SPDIF i/o

PHY

Intel® i219

PCIe

2x DVI/HDMI

PCI Slot 1

Intel® Core™ i7-6700/

Intel® Core™ i5-6500/ Intel® Core™ i3-6100/

Intel® Pentium® G4400/

Intel® Celeron® G3900

FDI

DMI

PCIe(PEG)

LPC

8x GPIO COM1-4

FAN1-4

PS2/KB

PS2/MS

PCIe to PCI

Bridge

PI7C9X111SL

PCI

PCI Slot 2

LAN 2

LAN 1

PCIe x4 Slot 1 & 4

PCIe x1 Slot 2

PCIe x1 Slot 3

USB 3.0

USB 1-4

Trusted

Platform

Module

SPI

USB2.0

USB 7-14

PCIe x16

2 Overview

2.1 Features

The CB1064 is a computer motherboard for industrial applications. Complying to the ATX form factor and based on Intel®'s Q170 PCH chipset, it is equipped with an LGA1151 CPU socket for Intel® CPUs of the 6th and 7th Generation Core™- families. Modern DDR4 technology provides top-notch memory performance, accommodating up to 64 GByte of RAM (DDR4-2133) via SO-DIMM260. Expansion cards can be added into two PCI slots, two PCIe x1 slots, two PCIe x4 slots and one PCIe x16 slots. The CB1064 also offers a wide range of internal and external connectors, such as four serial ports, two LAN connectors, 12 USB channels, six SATA connectors offering up to 6Gb/s, digital and analogue audio, DVI/HDMI connectors, DisplayPort connector, etc.

In addition the board serves via the integrated Trusted Platform Module as Trusted Computing Platform and provides essential safety functions.

Beckhoff New Automation Technology CB1064-xxxx page 13

Chapter: Overview Feature List

CB1064

ATX-Board

CPU

Intel® Core™ i5 6500TE (6M, 4 Cores, 35W TDP)

Intel® Core™ i7 6700TE (8M, 4 Cores, 35W TDP)

Chipset

Intel® Q170

Socket

LGA1151

Memory

4x DDR4@2133MHz à 16GB, SODIMM260 (NonECC), total memory capacity up to 64GByte

I/O

Internal

3x COM

6x SATA 3.0, RAID 0/1/5/10

2x PCI32-Slot

2x PCIe x1 (3.0) + 2x PCIe x4 (3.0) + 1x PCIe x16 (3.0)

8x USB 2.0

8x GPIO

4x FAN (from which 3 are regulated)

1x SMB interface

External

1x DisplayPort1.2

1x Sound (Mic, Line out, Aux)

1x PS/2 mouse & keyboard

2x DVI-D (DVI oder HDMI 1.4)

4x USB 3.0

2x GBit-LAN, Intel® i219/i210

1x COM

Graphics

HDMI1.4: 2560x1600@60Hz; 4096x2160@24Hz DisplayPort: 4096x2304@60Hz DVI: 1920x1200@60Hz

RTC

Internal or external CMOS battery

BIOS

AMI® Aptio V

Power Supply

Standard ATX PSU

Format

ATX (305mm x 220mm)

2.2 Feature List

page 14 Beckhoff New Automation Technology CB1064-xxxx

Specifications and Documents Chapter: Overview

2.3 Specifications and Documents

In making this manual and for further reading of technical documentation, the following documents, specifications and web-pages were used and are recommended.

 ATX Specification

Version 2.2

www.formfactors.com

 PCI Specification

Version 2.3 resp. 3.0

www.pcisig.com

 PCI Express® Base Specification

Version 2.0

www.pcisig.com

 ACPI Specification

Version 5.0

www.acpi.info

 ATA/ATAPI Specification

Version 7 Rev. 1

www.t13.org

 USB Specifications

www.usb.org

 SM-Bus Specification

Version 2.0

www.smbus.org

 Intel® Chipset Description

Intel® 8 Series Chipset datasheet

www.intel.com

 Intel® Chip Description

6th Gen. Intel® Core™ Processor Family Mobile datasheet

www.intel.com

 Intel® Chip Description

i219 Datasheet

www.intel.com

 Intel® Chip Description

i210 Datasheet

www.intel.com

 SMSC® Chip Description

SCH3114 Datasheet

www.smsc.com

(NDA required)

 Realtek® Chip Description

ALC885/889 Datasheet

www.realtek.com.tw

 American Megatrends®

Aptio™ Text Setup Environment (TSE) User Manual

www.ami.com

 American Megatrends®

Aptio™ 5.x Status Codes

www.ami.com

Beckhoff New Automation Technology CB1064-xxxx page 15

Chapter: Connectors Specifications and Documents

Notice

Please consider the requirements on the cabling!

For most interfaces, the cables must meet certain requirements. For instance, USB 2.0 requires twisted and shielded cables to reliably maintain full speed data rates. Restrictions on maximum cable length are also in place for many high speed interfaces and for power supply. Please refer to the respective specifications and use suitable cables at all times.

3 Connectors

This section describes all the connectors found on the CB1064.

page 16 Beckhoff New Automation Technology CB1064-xxxx

Power Supply, System Connectors, CPU Chapter: Connectors

Manufacturer

Description

Mating connector

Molex

39-29-3086

e.g. 39-01-2085

Manufacturer

Description

Mating Connector

Amphenol

MF42-SD-24LK

Standard ATX connector

Description

Name

Description

ground

GND

1 3 COREIN

12 volt supply

ground

GND

2 4 COREIN

12 volt supply

Description

Name

Description

3.3 volt supply

3.3V

1

13

3.3V

3.3 volt supply

3.3V

2

14

-12V

12 volt supply

ground

GND

3

15

GND

ground

5 volt supply

VCC

4

16

PS_ON

ground

GND

5

17

GND

ground

5 volt supply

VCC

6

18

GND

ground

GND

7

19

GND

ground

ATX Powergood

PWRGOOD

8

20

-5V

volt supply -5V

standby supply 5V

SVCC

9

21

VCC

5 volt supply

12 volt supply

12V

10

22

VCC

5 volt supply

12 volt supply

12V

11

23

VCC

5 volt supply

3.1 Power Supply, System Connectors, CPU

3.1.1 Power Supply

The connector for the power supply is a 2x12pin ATX connector ("ATX24"). It is accompanied by a 2x4pin connector, which must be used to provide the COREIN power supply.

2x4pin connector:

2x12pin connector:

Pinout ATX power connector 2x2:

Pinout "ATX24" power connector:

Beckhoff New Automation Technology CB1064-xxxx page 17

Chapter: Connectors Power Supply, System Connectors, CPU

Description

Name

Description

3.3 volt supply

3.3V

12

24

GND

ground

page 18 Beckhoff New Automation Technology CB1064-xxxx

Power Supply, System Connectors, CPU Chapter: Connectors

Manufacturer

Description

Mating Connector

Samtec

TSW-113-07-S-D

XXX-113-01-T-D

Description

Name

Description

on/suspend button

PWRBTN#

A1

B1

GND

ground

GND

A2

B2

N/C

reserved

N/C

A3

B3

PWLED#

power LED

ground

GND

A4

B4

N/C

reserved

5 volt supply

VCC

A5

B5

PWLED

3.3 volt supply

harddisk LED

HDLED#

A6

B6

N/C

reserved

5 volt supply

VCC

A7

B7

VCC

5 volt supply

reserved

N/C

A8

B8

GND

ground

IrDA transmit

IRTX

A9

B9

N/C

reserved

ground

GND

A10

B10

BEEP

speaker

reserved

N/C

A11

B11

N/C

reserved

N/C

A12

B12

GND

ground

5 volt supply

VCC

A13

B13

RESET#

reset

3.1.2 System

Typical signals for system control are provided through a 2x13 IDC socket connector with a spacing of

2.54mm. This connector combines signals for power button, reset, keyboard lock and several LEDs.

Pinout IDC socket connector "System 1":

Beckhoff New Automation Technology CB1064-xxxx page 19

Chapter: Connectors Power Supply, System Connectors, CPU

Notice

In case of improper insertion of the processor contacts can bend and therefore be damaged.

Processors must be ordered separately. The board ships without a CPU.

3.1.3 CPU Socket

The CB1064 board has an LGA1151 CPU socket accomodating certain versions of Intel®'s 6th and 7th Generation Core™ architecture CPUs. The LGA1151 is a socket, in which the processor is inserted and subsequently gets fixed by using the clamping bracket. There is only one orientation in which the processor will fit into the socket. Once the processor is in place, the clamping bracket must be fixed to ensure proper electrical contact.

page 20 Beckhoff New Automation Technology CB1064-xxxx

Power Supply, System Connectors, CPU Chapter: Connectors

Manufacturer

Description

Mating Connector

RenataSA

VBH2032-1

(battery)

Manufacturer

Description

Mating Connector

JST

B 2B-EH-A(LF)(SN)

JST 02HR-6S-P-N

Name

Description

1

BATT

battery 3.3 volt

2

GND

ground

3.1.4 CMOS Battery

The board ships with a CR2032 battery holder and 3V battery. Alternatively, an external battery can be connected via a 2pin connector.

2pin connector for external battery:

Beckhoff New Automation Technology CB1064-xxxx page 21

Chapter: Connectors Back Panel Connectors

Name

Description

1

TMDSDAT2#

DVI data 2 -

2

TMDSDAT2

DVI data 2 +

3

GND

ground

4

N/C

reserved

5

N/C

reserved

6

DDC CLK

DDC clock (DVI/VGA)

7

DDC DAT

DDC data (DVI/VGA)

8

N/C

reserved

9

TMDSDAT1#

DVI data 1 -

10

TMDSDAT1

DVI data 1 +

11

GND

ground

12

N/C

reserved

13

N/C

reserved

14

VCC

5 volt supply

15

GND

ground

16

HP_DETECT

hot plug detect

17

TMDSDAT0#

DVI data 0 -

18

TMDSDAT0

DVI data 0 +

19

GND

ground

20

N/C

reserved

21

N/C

reserved

3.2 Back Panel Connectors

The board complies with the ATX form factor and thus honours the "I/O Connector Area" as defined in the ATX specification. A range of standard connectors are available: You can connect PS/2 keyboard and mouse, displays, speakers, microphone, LAN, USB etc. If the board is mounted in a normal ATX compliant case, these connectors are located on the back side of the case.

3.2.1 DVI Connectors

The CB1064 has two DVI-D connectors combined in one component (Foxconn QH11121-DADF-4F). Digital DVI or HDMI displays can be attached to both connectors. The CPU's graphics system supports up to three independent displays.

Pinout DVI-D:

page 22 Beckhoff New Automation Technology CB1064-xxxx

Back Panel Connectors Chapter: Connectors

Name

Description

22

GND

ground

23

TMDS CLK

DVI clock +

24

TMDS CLK#

DVI clock -

C1

N/C

reserved

C2

N/C

reserved

C3

N/C

reserved

C4

N/C

reserved

C5

GND

ground

Beckhoff New Automation Technology CB1064-xxxx page 23

Chapter: Connectors Back Panel Connectors

Manufacturer

Description

Mating Connector

Molex

87831-1820

e.g. Molex 0791098658-ND

Description

Name

Description

HDMI panel detected

HPD_SINK

1 2 N/C

reserved

SMBus clock (DDC)

SCL_SINK

3 4 SDA_SINK

SMBus dat (DDC)

5 volt supply

VCC

5 6 GND

ground

GND

7 8 TMDS_CLK#

DVI clock -

DVI data 0 -

TMDS_D0#

9

10

TMDS_CLK

DVI clock +

DVI data 0 +

TMDS_D0

11

12

GND

ground

GND

13

14

TMDS_D1#

DVI data 1 -

DVI data 2 -

TMDS_D2#

15

16

TMDS_D1

DVI data 1 +

DVI data 2 +

TMDS_D2

17

18

GND

ground

3.2.2 DVI/HDMI

The CB1064 provides a second DVI interface which is realized as a 2x9pin header. Analog VGA is not available on this connector. However, an HDMI device can be connected. This connector and the lower DVI-D connector cannot be used simultaneously.

Pinout 2x9pin connector DVI/HDMI:

page 24 Beckhoff New Automation Technology CB1064-xxxx

Back Panel Connectors Chapter: Connectors

Description

Name

Description

Displayport Lane 0 +

DPL0

1 2 GND

Ground

Displayport Lane 0 -

DPL0#

3 4 DPL1

Displayport Lane 1 +

Ground

GND

5 6 DPL1#

Displayport Lane 1 -

Displayport Lane 2 +

DPL2

7 8 GND

Ground

Displayport Lane 2 -

DPL2#

9

10

DPL3

Displayport Lane 3 +

Ground

GND

11

12

DPL3#

Displayport Lane 3 -

Configuration pin 1

Config1

13

14

Config2

Configuration pin 2

Displayport Aux +

DPAUX

15

16

GND

Ground

Displayport Aux -

DPAUX#

17

18

HPD

Hotplug Detect

Ground

GND

19

20

3.3V

Power supply 3,3V

3.2.3 Display Port

For DisplayPort devices, a suitable standard connector is available (Foxconn 3VD11203-D7AB-4H). The interface also offers HDMI/DVI signals.

An adapter for using HDMI/DVI signals must be applied. Please consult your distributor for such an adapter.

Pinout DisplayPort connector:

Beckhoff New Automation Technology CB1064-xxxx page 25

Chapter: Connectors Back Panel Connectors

Description

Name

Description

mouse data

MDAT

B1

B2

N/C

reserved

ground

GND

B3

B4

(S)VCC

5 volt supply

mouse clock

MCLK

B5

B6

N/C

reserved

Description

Name

Description

keyboard data

KDAT

A1

A2

MDAT

mouse data

ground

GND

A3

A4

(S)VCC

5 volt supply

keyboard clock

KCLK

A5

A6

MCLK

mouse clock

3.2.4 PS/2 Keyboard and Mouse

PS/2 mice and keyboards are connected via standard mini-DIN connectors. If you want to use the keyboard or mouse to wake up the board from standby or suspend mode you have to activate this functionality by adjusting the KBPWR jumper settings (page 50). With this jumper you can switch from normal power supply (VCC) to standby power supply (SVCC) for keyboard/mouse. Some relevant settings will have to be adjusted in BIOS setup.

Pinout PS/2 mouse:

Pinout PS/2 keyboard:

page 26 Beckhoff New Automation Technology CB1064-xxxx

Back Panel Connectors Chapter: Connectors

Manufacturer

Description

Mating Connector

Foxconn

DM10151-N5W3-4F

standard DSUB connector

Description

Name

Description

data carrier detect

DCD

1 6 DSR

data set ready

receive data

RXD

2 7 RTS

request to send

transmit data

TXD

3 8 CTS

clear to send

data terminal ready

DTR

4 9 RI

ring indicator

ground

GND

5

3.2.5 Serial Port COM1

The serial port COM1 is made available via a 9 pin connector. Signals are RS232. The port address and the interrupt are set via the BIOS setup.

Pinout serial port (DSUB connector):

Beckhoff New Automation Technology CB1064-xxxx page 27

Chapter: Connectors Back Panel Connectors

Notice

For realtime applications, the external controller (MAC/PHY) is to prefer.

Name

Description

1

VCC

5 volt for USBX

2

USBX#

Minus channel USBX

3

USBX

Plus channel USBX

4

GND

ground

5

StdA_SSRX-

SuperSpeed Receiver -

6

StdA_SSRX+

SuperSpeed Receiver +

7

GND

ground

8

StdA_SSTX-

SuperSpeed Transmitter -

9

StdA_SSTX+

SuperSpeed Transmitter +

3.2.6 USB and LAN

To save space USB and LAN connectors are provided in the form of combo connectors. These comprise two USB connectors and one LAN connector. This way all board variants provide four external USB channels and two LAN ports. All USB channels support USB 3.0. You may note that the setting of USB keyboard or USB mouse support in the BIOS-setup is only necessary and advisable, if the OS offers no USB-support. BIOS-setup can be changed with a USB keyboard without enabling USB keyboard support. Running Windows with these features enabled may lead to significant performance or functionality limitations. The interfaces provide up to 900 mA current. All USB interfaces are protected by an electronically resettable fuse. The board also offers two Gigabit-LAN connectors. Both LAN connectors support 10/100/1000 Ethernet with automatic bandwith selection. Controller chips are the i219 (PHY, LAN1) and i210 (MAC/PHY, LAN2).

Pinout USB3.0 connector for channel X:

Pinout LAN 10/100/1000:

page 28 Beckhoff New Automation Technology CB1064-xxxx

Back Panel Connectors Chapter: Connectors

Name

Description

1

LAN2-0

LAN2 channel 0 plus

2

LAN2-0#

LAN2 channel 0 minus

3

LAN2-1

LAN2 channel 1 plus

4

LAN2-2

LAN2 channel 2 plus

5

LAN2-2#

LAN2 channel 2 minus

6

LAN2-1#

LAN2 channel 1 minus

7

LAN2-3

LAN2 channel 3 plus

8

LAN2-3#

LAN2 channel 3 minus

Beckhoff New Automation Technology CB1064-xxxx page 29

Chapter: Connectors Back Panel Connectors

3.2.7 Audio Connectors

Line-in, line-out, and microphone signals are provided in the form of three 3,5mm-TRS-connectors.

page 30 Beckhoff New Automation Technology CB1064-xxxx

SATA and Memory Chapter: Connectors

Name

Description

1

GND

ground

2

SATATX

SATA transmit +

3

SATATX#

SATA transmit -

4

GND

ground

5

SATARX

SATA receive -

6

SATARX#

SATA receive +

7

GND

ground

3.3 SATA and Memory

3.3.1 SATA Interfaces

The CB1064 provides six SATA interfaces. They all support transfer rates of 1,5Gbit/s up to 6Gbit/s.

Pinout SATA:

Beckhoff New Automation Technology CB1064-xxxx page 31

Chapter: Connectors SATA and Memory

Description

Name

Description

Ground

GND

1 2 GND

Ground

Data lane 5

DQ5

3 4 DQ4

Data lane 4

Ground

GND

5 6 GND

Ground

Data lane 1

DQ1

7 8 DQ0

Data lane 0

Ground

GND

9

10

GND

Ground

Data Strobe 0 -

DQS0_c

11

12

NC

Reserved

Data Strobe 0 +

DQS0_t

13

14

GND

Ground

GND

15

16

DQ6

Data lane 6

Data lane 7

DQ7

17

18

GND

Ground

GND

19

20

DQ2

Data lane 2

Data lane 3

DQ3

21

22

GND

Ground

GND

23

24

DQ12

Data lane 12

Data lane 13

DQ13

25

26

GND

Ground

GND

27

28

DQ8

Data lane 8

Data lane 9

DQ9

29

30

GND

Ground

GND

31

32

DQS1_c

Data Strobe 1 -

Reserved

NC

33

34

DQS1_t

Data Strobe 1 +

Ground

GND

35

36

GND

Ground

Data lane 15

DQ15

37

38

DQ14

Data lane 14

Ground

GND

39

40

GND

Ground

Data lane 10

DQ10

41

42

DQ11

Data lane 11

Ground

GND

43

44

GND

Ground

Data lane 21

DQ21

45

46

DQ20

Data lane 20

Ground

GND

47

48

GND

Ground

Data lane 17

DQ17

49

50

DQ16

Data lane 16

Ground

GND

51

52

GND

Ground

3.3.2 Memory

The CB1064 is equipped with four SO-DIMM260 sockets for DDR4-2133-RAM. For technical and mechanical reasons it is possible that particular memory modules cannot be employed. Please ask your distributor for recommended memory modules With currently available memory modules a memory extension up to 64 GByte is possible. All timing parameters for different memory modules are automatically set by BIOS.

page 32 Beckhoff New Automation Technology CB1064-xxxx

SATA and Memory Chapter: Connectors

Description

Name

Description

Data Strobe 2 -

DQS2_c

53

54

NC

Reserved

Data Strobe 2 +

DQS2_t

55

56

GND

Ground

GND

57

58

DQ22

Data lane 22

Data lane 23

DQ23

59

60

GND

Ground

GND

61

62

DQ18

Data lane 18

Data lane 19

DQ19

63

64

GND

Ground

GND

65

66

DQ28

Data lane 28

Data lane 29

DQ29

67

68

GND

Ground

GND

69

70

DQ24

Data lane 24

Data lane 25

DQ25

71

72

GND

Ground

GND

73

74

DQS3_c

Data Strobe 3 -

Reserved

NC

75

76

DQS3_t

Data Strobe 3 +

Ground

GND

77

78

GND

Ground

Data lane 30

DQ30

79

80

DQ31

Data lane 31

Ground

GND

81

82

GND

Ground

Data lane 26

DQ26

83

84

DQ27

Data lane 27

Ground

GND

85

86

GND

Ground

Reserved

NC

87

88

NC

Reserved

Ground

GND

89

90

GND

Ground

Reserved

NC

91

92

NC

Reserved

Ground

GND

93

94

GND

Ground

Data Strobe 8 -

DQS8_c

95

96

NC

Reserved

Data Strobe 8 +

DQS8_t

97

98

GND

Ground

GND

99

100

NC

Reserved

NC

101

102

GND

Ground

GND

103

104

NC

Reserved

NC

105

106

GND

Ground

GND

107

108

RESET_n

Reset

Clock Enable 0

CKE0

109

110

CKE1

Clock Enable 1

Power supply 1,2V

VCC

111

112

VCC

Power supply 1,2V

Bank Group Input 1

BG1

113

114

ACT_n

Activation Command Input

Bank Group Input 0

BG0

115

116

ALERT_n

Alert

Power supply 1,2V

VCC

117

118

VCC

Power supply 1,2V

Address lane 12

A12

119

120

A11

Address lane 11

Address lane 9

A9

121

122

A7

Address lane 7

Power supply 1,2V

VCC

123

124

VCC

Power supply 1,2V

Address lane 8

A8

125

126

A5

Address lane 5

Address lane 6

A6

127

128

A4

Address lane 4

Power supply 1,2V

VCC

129

130

VCC

Power supply 1,2V

Address lane3

A3

131

132

A2

Address lane 2

Address lane 1

A1

133

134

EVENT_n

Event

Power supply 1,2V

VCC

135

136

VCC

Power supply 1,2V

Clock-Signal 0 +

CK0_t

137

138

CK1_t

Clock 1 +

Clock-Signal 0 -

CK0_c

139

140

CK1_c

Clock 1 -

Power supply 1,2V

VCC

141

142

VCC

Power supply 1,2V

Even parity check

Parity

143

144

A0

Address lane 0

SDRAM Bank 2

BA1

145

146

A10/AP

Address lane 10/Autoprecharge

Power supply 1,2V

VCC

147

148

VCC

Power supply 1,2V

Chip Select 0

CS0_n

149

150

BA0

Bank Adress 0

Address lane 14/Write Enable

A14/WE_n

151

152

A16/RAS_n

Address lane 16/Row Address Strobe

Power supply 1,2V

VCC

153

154

VCC

Power supply 1,2V

On Die Termination 0

ODT0

155

156

A15/CAS_n

Address lane 15/Column Address Strobe

Beckhoff New Automation Technology CB1064-xxxx page 33

Chapter: Connectors SATA and Memory

Description

Name

Description

Chip Select 1

CS1_n

157

158

A13

Address lane 13

Power supply 1,2V

VCC

159

160

VCC

Power supply 1,2V

On Die Termination 1

ODT1

161

162

NC

Reserved

Power supply 1,2V

VCC

163

164

VREFCA

Reference voltage

Reserved

NC

165

166

SA2

SPD address 2

Ground

GND

167

168

GND

Ground

Data lane 37

DQ37

169

170

DQ36

Data lane 36

Ground

GND

171

172

GND

Ground

Data lane 33

DQ33

173

174

DQ32

Data lane 32

Ground

GND

175

176

GND

Ground

Data Strobe 4 -

DQS4_c

177

178

NC

Reserved

Data Strobe 4 +

DQS4_t

179

180

GND

Ground

GND

181

182

DQ39

Data lane 39

Data lane 38

DQ38

183

184

GND

Ground

GND

185

186

DQ35

Data lane 35

Data lane 34

DQ34

187

188

GND

Ground

GND

189

190

DQ45

Data lane 45

Data lane 44

DQ44

191

192

GND

Ground

GND

193

194

DQ41

Data lane 41

Data lane 40

DQ40

195

196

GND

Ground

GND

197

198

DQS5_c

Data Strobe 5 -

Reserved

NC

199

200

DQS5_t

Data Strobe 5 +

Ground

GND

201

202

GND

Ground

Data lane 46

DQ46

203

204

DQ47

Data lane 47

Ground

GND

205

206

GND

Ground

Data lane 42

DQ42

207

208

DQ43

Data lane 43

Ground

GND

209

210

GND

Ground

Data lane 52

DQ52

211

212

DQ53

Data lane 53

Ground

GND

213

214

GND

Ground

Data lane 49

DQ49

215

216

DQ48

Data lane 48

Ground

GND

217

218

GND

Ground

Data Strobe 6 -

DQS6_c

219

220

NC

Reserved

Data Strobe 6 +

DQS6_t

221

222

GND

Ground

GND

223

224

DQ54

Data lane 54

Data lane 55

DQ55

225

226

GND

Ground

GND

227

228

DQ50

Data lane 50

Data lane 51

DQ51

229

230

GND

Ground

GND

231

232

DQ60

Data lane 60

Data lane 61

DQ61

233

234

GND

Ground

GND

235

236

DQ57

Data lane 57

Data lane 56

DQ56

237

238

GND

Ground

Masse

GND

239

240

DQS7_c

Data Strobe 7 -

Reserved

NC

241

242

DQS7_t

Data Strobe 7 +

Ground

GND

243

244

GND

Ground

Data lane 62

DQ62

245

246

DQ63

Data lane 63

Ground

GND

247

248

GND

Ground

Data lane 58

DQ58

249

250

DQ59

Data lane 59

Ground

GND

251

252

GND

Ground

SMBus Clock

SCL

253

254

SDA

SMBus Data

I²C Power for SPD EEProm

VCCSPD

255

256

SA0

SPD address 0

DRAM Activating Power

VPP

257

258

VTT

Termination voltage

DRAM Activating Power

VPP

259

260

SA1

SPD address 1

page 34 Beckhoff New Automation Technology CB1064-xxxx

Internal Connectors Chapter: Connectors

Manufacturer

Description

Mating connector

FCI

75869-301LF

e.g. 71600-610LF

Description

Name

Description

5 volt for USBx

VCC

1 2 VCC

5 volt for USBy

minus channel USBx

USBx#

3 4 USBy#

minus channel USBy

plus channel USBx

USBx

5 6 USBy

plus channel USBy

ground

GND

7 8 GND

ground

reserved

N/C

9

10

N/C

reserved

3.4 Internal Connectors

3.4.1 USB 2.0

The USB channels 7 to 14 are provided via four 2x5 pin connectors. They support USB2.0 You may note that the setting of USB keyboard or USB mouse support in the BIOS-setup is only necessary and advisable, if the OS offers no USB-support. BIOS-setup can be changed with a USB keyboard without enabling USB keyboard support. Running Windows with these features enabled may lead to significant performance or functionality limitations.

Each USB interface provides up to 500mA current and is protected by an electronically resettable fuse. 2x5pin connector:

Pinout 2x5 pin connector USB x/y:

Beckhoff New Automation Technology CB1064-xxxx page 35

Chapter: Connectors Internal Connectors

Manufacturer

Description

Mating connector

FCI

75869-301LF

e.g. 71600-610LF

Description

Name

Description

data carrier detect

DCD

1 2 DSR

data set ready

receive data

RXD

3 4 RTS

request to send

transmit data

TXD

5 6 CTS

clear to send

data terminal ready

DTR

7 8 RI

ring indicator

ground

GND

9

10

VCC

5 volt supply

3.4.2 Serial ports COM2 to COM4

The three serial ports COM2 to COM4 are made available via a 2x5 pin connector each. Signals are RS232. The port address and the interrupt are set via the BIOS setup.

2x5pin connector:

Pinout COM connector:

page 36 Beckhoff New Automation Technology CB1064-xxxx

Internal Connectors Chapter: Connectors

Name

Description

1

CD_L

CD left channel

2

CD_GND

CD ground

3

CD_GND

CD ground

4

CD_R

CD right channel

3.4.3 CD-In

In addition to the external TRS connectors mentioned above, the CB1064 offers an internal 4 pin connector (Foxconn HF1104E-P1), providing customers with even more possibilities to connect audio devices (analogue signals).

Pinout CD-in connector:

Beckhoff New Automation Technology CB1064-xxxx page 37

Chapter: Connectors Internal Connectors

Manufacturer

Description

Mating Connector

Samtec

TSW-103-07-S-D

e.g. (XXX)-103-01-T-D

Description

Name

Description

ground

GND

1 2 SPDIFO

SPDIF out

3.3 volt supply

3,3V

3 4 VCC

5 volt supply

ground

GND

5 6 SPDIFI

SPDIF in

3.4.4 S/PDIF

For digital audio signals an SPDIF interface is available, which can be accessed using an internal 2x3 pin IDC socket connector with a spacing of 2,54mm.

Pinout SPDIF connector:

page 38 Beckhoff New Automation Technology CB1064-xxxx

Internal Connectors Chapter: Connectors

Notice

Please note that due to the nature of the PCI bus some signals in the following table are different from one PCI slot to the other. This applies to the test signals (A4, B4), the interrupt signals (A6, A7, B7, B8), the clock signal (B16), the grant signal (A17), the request signal (B18), and the ID-select signal (A26).

Description

Name

Description

test logic reset

TRST#

A1

B1

-12V

-12 volt supply

12 volt supply

12V

A2

B2

TCK

test clock

test mde select

TMS

A3

B3

GND

ground

test data input

TDI

A4

B4

TDO

test data output

5 volt supply

VCC

A5

B5

VCC

5 volt supply

interrupt A

INTA#

A6

B6

VCC

5 volt supply

interrupt C

INTC#

A7

B7

INTB#

interrupt B

5 volt supply

VCC

A8

B8

INTD#

interrupt D

reserved

N/C

A9

B9

GND

ground

5 volt supply

VCC

A10

B10

N/C

reserved

N/C

A11

B11

GND

ground

GND

A12

B12

GND

ground

GND

A13

B13

GND

ground

3.3 volt supply

3.3VAux

A14

B14

N/C

reserved

PCI reset

PRST#

A15

B15

GND

ground

5 volt supply

VCC

A16

B16

PCLK

clock

grant PCI use

GNT#

A17

B17

GND

ground

GND

A18

B18

REQ#

request

power management event

PME#

A19

B19

VCC

5 volt supply

address/data 30

AD30

A20

B20

AD31

address/data 31

3.3 volt supply

3.3V

A21

B21

AD29

address/data 29

address/data 28

AD28

A22

B22

GND

ground

address/data 26

AD26

A23

B23

AD27

address/data 27

3.4.5 PCI Interfaces

There are two standard PCI slots available on the CB1064.

Pinout PCI slot:

Beckhoff New Automation Technology CB1064-xxxx page 39

Chapter: Connectors Internal Connectors

Description

Name

Description

ground

GND

A24

B24

AD25

address/data 25

address/data 24

AD24

A25

B25

3.3V

3.3 volt supply

init device select

IDSEL

A26

B26

CBE3#

command, byte enable 3

3.3 volt supply

3.3V

A27

B27

AD23

address/data 23

address/data 22

AD22

A28

B28

GND

ground

address/data 20

AD20

A29

B29

AD21

address/data 21

ground

GND

A30

B30

AD19

address/data 19

address/data 18

AD18

A31

B31

3.3V

3.3 volt supply

address/data 16

AD16

A32

B32

AD17

address/data 17

3.3 volt supply

3.3V

A33

B33

CBE2#

command, byte enable 2

cycle frame

FRAME#

A34

B34

GND

ground

GND

A35

B35

IRDY#

initiator ready

Target Ready

TRDY#

A36

B36

3.3V

3.3 volt supply

ground

GND

A37

B37

DEVSEL#

device select

stop request by target

STOP#

A38

B38

GND

ground

3.3 volt supply

3.3V

A39

B39

PLOCK#

lock bus

SMBus clock PCI

SMBCLK

A40

B40

PERR#

parity error

SMBus data PCI

SMBDAT

A41

B41

3.3V

3.3 volt supply

ground

GND

A42

B42

SERR#

system error

parity

PAR

A43

B43

3.3V

3.3 volt supply

address/data 15

AD15

A44

B44

CBE1#

command, byte enable 1

3.3 volt supply

3.3V

A45

B45

AD14

address/data 14

address/data 13

AD13

A46

B46

GND

ground

address/data 11

AD11

A47

B47

AD12

address/data 12

ground

GND

A48

B48

AD10

address/data 10

address/data 9

AD9

A49

B49

GND

ground

coded

N/C

A50

B50

N/C

coded

N/C

A51

B51

N/C

coded

command, byte enable 0

CBEO#

A52

B52

AD8

address/data 8

3.3 volt supply

3.3V

A53

B53

AD7

address/data 7

address/data 6

AD6

A54

B54

3.3V

3.3 volt supply

address/data 4

AD4

A55

B55

AD5

address/data 5

ground

GND

A56

B56

AD3

address/data 3

address/data 2

AD2

A57

B57

GND

ground

address/data 0

AD0

A58

B58

AD1

address/data 1

5 volt supply

VCC

A59

B59

VCC

5 volt supply

reserved

N/C

A60

B60

VCC

5 volt supply

VCC

A61

B61

VCC

5 volt supply

VCC

A62

B62

VCC

5 volt supply

page 40 Beckhoff New Automation Technology CB1064-xxxx

Internal Connectors Chapter: Connectors

Notice

Please note that some signals in the following table are different from one PCIe slot to the other. This applies to the clock signals (A13, A14), the receive signals (A16, A17), and the transmit signals (B14, B15).

Description

Name

Description

hot plug detect 1

PRSNT1#

A1

B1

12V

12 volt supply

12V

A2

B2

12V

12 volt supply

12V

A3

B3

N/C

reserved

ground

GND

A4

B4

GND

ground

reserved

N/C

A5

B5

SMBCLK

SMBus clock PCIe

reserved

N/C

A6

B6

SMBDAT

SMBus data PCIe

reserved

N/C

A7

B7

GND

ground

reserved

N/C

A8

B8

3.3V

3.3 volt supply

3.3V

A9

B9

N/C

reserved

3.3 volt supply

3.3V

A10

B10

S3.3V

3.3V standby-supply

PCIe reset

PERST#

A11

B11

PEWAKE#

link reactivation

ground

GND

A12

B12

N/C

reserved

reference clock +

REFCLK

A13

B13

GND

ground

reference clock -

REFCLK#

A14

B14

PET0

transmit lane 0 +

ground

GND

A15

B15

PET0#

transmit lane 0 -

receive lane 0 +

PER0

A16

B16

GND

ground

receive lane 0 -

PER0#

A17

B17

PRSNT2#

hot plug detect 2

ground

GND

A18

B18

GND

ground

3.4.6 PCI-express Interfaces (x1)

The CB1064 board has two slots for PCIe-x1 expansion cards.

Pinout PCI-express-x1 connector:

Beckhoff New Automation Technology CB1064-xxxx page 41

Chapter: Connectors Internal Connectors

Description

Name

Description

hot plug detect 1

PRSNT1#

A1

B1

12V

12V supply

12V

A2

B2

12V

12V supply

12V

A3

B3

N/C

reserved

ground

GND

A4

B4

GND

ground

reserved

N/C

A5

B5

SMBCLK

SMBus clock PCIe

reserved

N/C

A6

B6

SMBDAT

SMBus data PCIe

reserved

N/C

A7

B7

GND

ground

reserved

N/C

A8

B8

3,3V

3.3V supply

3,3V

A9

B9

N/C

reserved

3.3V supply

3,3V

A10

B10

S3,3V

3.3V standby

PCIe reset

PERST#

A11

B11

PEWAKE#

link reactivation

ground

GND

A12

B12

N/C

reserved

reference clock +

REFCLK

A13

B13

GND

ground

reference clock -

REFCLK#

A14

B14

PET0

transmit lane 0 +

ground

GND

A15

B15

PET0#

transmit lane 0 -

receive lane 0 +

PER0

A16

B16

GND

ground

receive lane 0 -

PER0#

A17

B17

PRSNT2#

hot plug detect 2

ground

GND

A18

B18

GND

ground

reserved

N/C

A19

B19

PET1

transmit lane 1 +

ground

GND

A20

B20

PET1#

transmit lane 1 -

receive lane 1 +

PER1

A21

B21

GND

ground

receive lane 1 -

PER1#

A22

B22

GND

ground

GND

A23

B23

PET2

transmit lane 2 +

ground

GND

A24

B24

PET2#

transmit lane 2 -

receive lane 2 +

PER2

A25

B25

GND

ground

receive lane 2 -

PER2#

A26

B26

GND

ground

GND

A27

B27

PET3

transmit lane 3 +

ground

GND

A28

B28

PET3#

transmit lane 3 -

receive lane 3 +

PER3

A29

B29

GND

ground

3.4.7 PCI-express Interfaces (x4)

The CB1064 has two slots for PCIe-x4 expansion cards. This slots also accomodates x1 expansion cards.

Pinout PCI-express-x1 connector:

page 42 Beckhoff New Automation Technology CB1064-xxxx

Internal Connectors Chapter: Connectors

Description

Name

Description

receive lane 3 -

PER3#

A30

B30

N/C

reserved

ground

GND

A31

B31

PRSNT2#

hot plug detect 2

reserved

N/C

A32

B32

GND

ground

Beckhoff New Automation Technology CB1064-xxxx page 43

Chapter: Connectors Internal Connectors

Description

Name

Description

hot plug detect 1

PRSNT1#

A1

B1

12V

12 volt supply

12V

A2

B2

12V

12 volt supply

12V

A3

B3

N/C

reserved

ground

GND

A4

B4

GND

ground

reserved

N/C

A5

B5

SMBCLK

SMBus clock PCIe

reserved

N/C

A6

B6

SMBDAT

SMBus data PCIe

reserved

N/C

A7

B7

GND

ground

reserved

N/C

A8

B8

3.3V

3.3 volt supply

3.3V

A9

B9

N/C

reserved

3.3 volt supply

3.3V

A10

B10

S3.3V

3.3V standby-supply

PCIe reset

PERST#

A11

B11

PEWAKE#

link reactivation

ground

GND

A12

B12

N/C

reserved

reference clock +

REFCLK

A13

B13

GND

ground

reference clock -

REFCLK#

A14

B14

PET0

transmit lane 0 +

ground

GND

A15

B15

PET0#

transmit lane 0 -

receive lane 0 +

PER0

A16

B16

GND

ground

receive lane 0 -

PER0#

A17

B17

PRSNT2#

hot plug detect 2

ground

GND

A18

B18

GND

ground

reserved

N/C

A19

B19

PET1

transmit lane 1 +

ground

GND

A20

B20

PET1#

transmit lane 1 -

receive lane 1 +

PER1

A21

B21

GND

ground

receive lane 1 -

PER1#

A22

B22

GND

ground

GND

A23

B23

PET2

transmit lane 2 +

ground

GND

A24

B24

PET2#

transmit lane 2 -

receive lane 2 +

PER2

A25

B25

GND

ground

receive lane 2 -

PER2#

A26

B26

GND

ground

GND

A27

B27

PET3

transmit lane 3 +

ground

GND

A28

B28

PET3#

transmit lane 3 -

receive lane 3 +

PER3

A29

B29

GND

ground

3.4.8 PCI-express Interface (x16)

One slot for PCI-express-x16-cards makes the expansion options on the CB1064 complete. You can use this slot for PCIe-x16 graphic adapters. This slot also acommodates x1 or x4 expansion cards.

Pinout PCI-express-x16 connector:

page 44 Beckhoff New Automation Technology CB1064-xxxx

Internal Connectors Chapter: Connectors

Description

Name

Description

receive lane 3 -

PER3#

A30

B30

N/C

reserved

ground

GND

A31

B31

PRSNT2#

hot plug detect 2

reserved

N/C

A32

B32

GND

ground

reserved

N/C

A33

B33

PET4

transmit lane 4 +

ground

GND

A34

B34

PET4#

transmit lane 4 -

receive lane 4 +

PER4

A35

B35

GND

ground

receive lane 4 -

PER4#

A36

B36

GND

ground

GND

A37

B37

PET5

transmit lane 5 +

ground

GND

A38

B38

PET5#

transmit lane 5 -

receive lane 5 +

PER5

A39

B39

GND

ground

receive lane 5 -

PER5#

A40

B40

GND

ground

GND

A41

B41

PET6

transmit lane 6 +

ground

GND

A42

B42

PET6#

transmit lane 6 -

receive lane 6 +

PER6

A43

B43

GND

ground

receive lane 6 -

PER6#

A44

B44

GND

ground

GND

A45

B45

PET7

transmit lane 7 +

ground

GND

A46

B46

PET7#

transmit lane 7 -

receive lane 7 +

PER7

A47

B47

GND

ground

receive lane 7 -

PER7#

A48

B48

PRSNT2#

hot plug detect 2

ground

GND

A49

B49

GND

ground

reserved

N/C

A50

B50

PET8

transmit lane 8 +

ground

GND

A51

B51

PET8#

transmit lane 8 -

receive lane 8 +

PER8

A52

B52

GND

ground

receive lane 8 -

PER8#

A53

B53

GND

ground

GND

A54

B54

PET9

transmit lane 9 +

ground

GND

A55

B55

PET9#

transmit lane 9 -

receive lane 9 +

PER9

A56

B56

GND

ground

receive lane 9 -

PER9#

A57

B57

GND

ground

GND

A58

B58

PET10

transmit lane 10 +

ground

GND

A59

B59

PET10#

transmit lane 10 -

receive lane 10 +

PER10

A60

B60

GND

ground

receive lane 10 -

PER10#

A61

B61

GND

ground

GND

A62

B62

PET11

transmit lane 11 +

ground

GND

A63

B63

PET11#

transmit lane 11 -

receive lane 11 +

PER11

A64

B64

GND

ground

receive lane 11 -

PER11#

A65

B65

GND

ground

GND

A66

B66

PET12

transmit lane 12 +

ground

GND

A67

B67

PET12#

transmit lane 12 -

receive lane 12 +

PER12

A68

B68

GND

ground

receive lane 12 -

PER12#

A69

B69

GND

ground

GND

A70

B70

PET13

transmit lane 13 +

ground

GND

A71

B71

PET13#

transmit lane 13 -

receive lane 13+

PER13

A72

B72

GND

ground

receive lane 13-

PER13#

A73

B73

GND

ground

GND

A74

B74

PET14

transmit lane 14 +

ground

GND

A75

B75

PET14#

transmit lane 14 -

receive lane 14 +

PER14

A76

B76

GND

ground

receive lane 14 -

PER14#

A77

B77

GND

ground

GND

A78

B78

PET15

transmit lane 15 +

ground

GND

A79

B79

PET15#

transmit lane 15 -

receive lane 15 +

PER15

A80

B80

GND

ground

receive lane 15 -

PER15#

A81

B81

N/C

reserved

ground

GND

A82

B82

N/C

reserved

Beckhoff New Automation Technology CB1064-xxxx page 45

Chapter: Connectors Internal Connectors

Manufacturer

Description

Mating Connector

JST

B10B-PHDSSLFSN

e.g. PHDR-10VS

Description

Name

Description

3.3 volt supply

3.3V

1 6 GND

ground

SMBus clock

SMBCLK

2 7 SMBDAT

SMBus data

SMBus alarm

SMBALRT#

3 8 SVCC

standby supply 5V

I2C bus clock

I2CLK

4 9 I2DAT

I2C bus data

5 volt supply

VCC

5

10

GND

ground

3.4.9 SMB/I2C

The CB1064 can communicate with external devices via the SMBus protocol or the I2C protocol. The signals for these protocols are available through a 2x5 pin connector. The SMBus signals are processed by the chipset, the I2C signals are processed by the SIO unit.

Pinout SMBus/I2C connector:

page 46 Beckhoff New Automation Technology CB1064-xxxx

Internal Connectors Chapter: Connectors

Manufacturer

Description

Mating Connector

JST

B20B-PHDSSLFSN

PHDR-20VS

Description

Name

Description

5 volt supply

VCC

1

11

VCC

5 volt supply

GP input/output 10

GPIO10

2

12

N/C

reserved

GP input/output 11

GPIO11

3

13

N/C

reserved

GP input/output 12

GPIO12

4

14

N/C

reserved

GP input/output 13

GPIO13

5

15

N/C

reserved

GP input/output 14

GPIO14

6

16

N/C

reserved

GP input/output 15

GPIO15

7

17

N/C

reserved

GP input/output 16

GPIO16

8

18

N/C

reserved

GP input/output 17

GPIO17

9

19

N/C

reserved

ground

GND

10

20

GND

ground

3.4.10 GPIO

The General Purpose Input/Output interface is made available through a 2x10 pin connector. To make use of this interface the SIO unit must be programmed accordingly. Please refer to your distributor for information on available software support.

Beckhoff New Automation Technology CB1064-xxxx page 47

Chapter: Connectors Internal Connectors

Manufacturer

Description

Mating Connector

Molex

22-23-2031

e.g. 22-01-2037

Name

Description

1

GND

ground

2

12V

12 volt supply regulated

3

TACHO

fan monitoring signal

Notice

The FAN4 connector doesn't have pin 3 connected (N/C).

3.4.11 Fan Connectors

Four 3 pin connectors are available for attaching external 12V fans. All connectors except FAN4 can monitor fan speed. For this to work the fans must provide a corresponding speed signal.

Pinout fan connector:

page 48 Beckhoff New Automation Technology CB1064-xxxx

Jumper Settings Chapter: Connectors

Notice

In order to avoid an undefined system state it is essential to ensure that the shorting of jumper Clear CMOS 1 (J1800) takes place BEFORE and only combined with the shorting of jumper Clear CMOS 2 (J1801).

Furthermore please notice, that if you reset the CMOS this does not only bring all settings made in BIOS setup back to default values, it also clears the date and time information stored in CMOS. So don't forget that, after the Clear CMOS procedure, you will have to set the clock again.

3.5 Jumper Settings

3.5.1 Clear CMOS

In case the board doesn't start up anymore and BIOS setup is inaccessible there is a "last resort": You can use the "Clear CMOS" jumpers to reset all CMOS settings to factory defaults. In order to do so you need to shut down the computer, change the jumper settings from normal (pins 1 & 2 short) to "Clear CMOS" (pins 2 & 3 short) first on jumper Clear CMOS 1 and then on jumper Clear CMOS 2, wait a few seconds, put the jumpers back into normal position and reboot.

Beckhoff New Automation Technology CB1064-xxxx page 49

Chapter: Connectors Jumper Settings

3.5.2 Jumper: Keyboard Power (KBPWR)

Power supply for keyboard and mouse can be provided in two different ways, either using normal power supply VCC or standby power supply SVCC. You can switch between the two by using the KBPWR jumper. For VCC you need to short pins 1 and 2, for SVCC please short pins 2 and 3.

page 50 Beckhoff New Automation Technology CB1064-xxxx

General Remarks Chapter: BIOS-Einstellungen

Hinweis

Hinweis zur Setup-Dokumentation

Das BIOS wird regelmäßig weiterentwickelt, so dass die verfügbaren Setup-Optionen sich jederzeit und ohne gesonderte Mitteilung ändern können. Dadurch kann es zu Abweichungen kommen zwischen den tatsächlich vorhandenen Optionen und denen, die nachfolgend beschrieben werden. Zu beachten ist außerdem, dass die in den Setup-Menüs im Folgenden gezeigten Einstellungen nicht notwendigerweise die empfohlenen oder die Default-Einstellungen sind. Welche Einstellungen gewählt werden müssen, hängt jeweils vom Anwendungsszenario ab, in dem das Board betrieben wird.

4 BIOS-Einstellungen

4.1 General Remarks

In each setup page, standard values for all setup entries can be loaded. Previously saved settings are loaded by pressing F2 and factory defaults are loaded with F3. Both F2 and F3, and also F4 ("Save & Exit") always affect the whole set of setup entries.

Setup entries starting with a „►" sign represent submenus. Navigation between entries is done using the

arrow keys on the keyboard, with the <Enter> key being used to select an entry, which either opens up a dialog box or opens a whole new submenu of setup entries. Each setup entry has a short help text associated with it. This is displayed in the upper right hand corner of the screen.

Beckhoff New Automation Technology CB1064-xxxx page 51

Kapitel: BIOS-Einstellungen Main

4.2 Main

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ │Set the Date. Use Tab to │ │ Board Information │switch between Data elements. │ │ Board CB1064 │ │ │ Revision 2 │ │ │ Bios Version 1.01 │ │ │ │ │ │ Processor Information │ │ │ Name SkyLake DT │ │ │ Type Intel(R) Core(TM) │ │ │ i5-6400 CPU @ 2.70GHz │ │ │ Speed 2700 MHz │ │ │ ID 0x506E3 │ │ │ Stepping R0/S0/N0 │────────────────────────────────│ │ Number of Processors 4Core(s) / 4 Thread(s) │→←: Select Screen │ │ Microcode Revision A6 │↑↓: Select Item │ │ GT Info GT2 (0x1912) │Enter: Select │ │ │+/-: Change Opt. │ │ IGFX VBIOS Version 1049 │F1: General Help │ │ IGFX GOP Version N/A │F2: Previous Values │ │ Memory RC Version 2.0.0.6 │F3: Optimized Defaults │ │ Total Memory 4096 MB │F4: Save & Exit │ │ Memory Frequency 2133 MHz │ESC: Exit │ │ │ │ │ System Date [Wed 05/07/2017) │ │ │ System Time [13:25:06] │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Board

Options: none

 Revision

Options: none

 Bios Version

Options: none

 Processor Information

Options: none

 Name

Options: none

 Type

Options: none

 Speed

Options: none

 ID

Options: none

 Stepping

Options: none

 Number of Processors

Options: none

 Microcode Revision

Options: none

Seite 52 Beckhoff New Automation Technology CB1064-xxxx

Main Kapitel: BIOS-Einstellungen  GT Info

Options: none

 IGFX VBIOS Version

Options: none

 IGFX GOP Version

Options: none

 Memory RC Version

Options: none

 Total Memory

Options: none

 Memory Frequency

Options: none

 System Date

Options: The system date can be adjusted here.

 System Time

Options: The system time can be adjusted here.

Beckhoff New Automation Technology CB1064-xxxx Seite 53

Kapitel: BIOS-Einstellungen Advanced

4.3 Advanced

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Power-Supply Type [ATX] │Trusted Computing Settings │ │ SoftOff on Overheat [Disabled] │ │ │► Platform Misc Configuration │ │ │► CPU Configuration │ │ │► Intel(R) I210 Gigabit Network Connection - │ │ │ 00:01:05:2C:0B:3F │ │ │► Intel(R) Ethernet Connection (2) I219-LM - 00:01:05:2C:0B:3E │ │ │► Driver Health │ │ │► Trusted Computing │ │ │► ACPI Settings │ │ │► SCH3114 Super IO Configuration │ │ │► Hardware Monitor │ │ │► Serial Port Console Redirection │────────────────────────────────│ │► PCI Subsystem Settings │→←: Select Screen │ │► Network Stack Configuration │↑↓: Select Item │ │► Power Controller Options │Enter: Select │ │► CSM Configuration │+/-: Change Opt. │ │► NVMe Configuration │F1: General Help │ │► USB Configuration │F2: Previous Values │ │► SATA and RST Configuration │F3: Optimized Defaults │ │► AMT Configuration │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Power-Supply Type

Options: ATX / AT

 SoftOff on Overheat

Options: Disabled / Enabled

 Platform Misc Configuration

Sub menu: see "Platform Misc Configuration Configuration" (page 56)

 CPU Configuration

Sub menu: see "CPU Configuration" (page 60)

 Intel(R) I210 Gigabit Network Connection

Sub menu: see "Intel(R) I210 Gigabit Network Connection" (page 64)

 Intel(R) Ethernet Connection (2) I219-LM

Sub menu: see "Intel(R) Ethernet Connection I219-LM" (page 66)

 Driver Health

Sub menu: see "Driver Health" (page 67)

 Trusted Computing

Sub menu: see "Trusted Computing" (page 70)

 ACPI Settings

Sub menu: see "ACPI Settings" (page 71)

 SCH3114 Super IO Configuration

Sub menu: see "SCH3114 Super IO Configuration" (page 72)

 H/W Monitor

Sub menu: see "H/W Monitor" (page 74)

Seite 54 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen  Serial Port Console Redirection

Sub menu: see "Serial Port Console Redirection" (page 76)

 PCI Subsystem Settings

Sub menu: see "PCI Subsystem Settings" (page 79)

 Network Stack Configuration

Sub menu: see "Network Stack Configuration" (page 81)

 Power Controller Options

Sub menu: see "Power Controller Options" (page 82)

 CSM Configuration

Sub menu: see "Compatibility Support Module Configuration" (page 84)

 NVMe Configuration

Sub menu: see "NVMe Controller and Drive Information" (page 85)

 USB Configuration

Sub menu: see "USB Configuration" (page 86)

 SATA and RST Configuration

Sub menu: see "SATA and RST Configuration" (page 87)

 AMT Configuration

Sub menu: see "AMT Configuration" (page 91)

Beckhoff New Automation Technology CB1064-xxxx Seite 55

Kapitel: BIOS-Einstellungen Advanced

4.3.1 Platform Misc Configuration Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Platform Misc Configuration │PTID Support will be loaded if │ │ │enabled. │ │ PTID Support [Enabled] │ │ │ PECI Access Method [Direct I/O] │ │ │ Native PCIE Enable [Enabled] │ │ │ Native ASPM [Disabled] │ │ │ BDAT ACPI Table Support [Disabled] │ │ │ │ │ │ Wake system from S5 [Enabled] │ │ │ Wake up hour 0 │ │ │ Wake up minute 0 │ │ │ Wake up second 0 │ │ │ ACPI Debug [Enabled] │────────────────────────────────│ │ Acpi Memory Buffer Address N/A │→←: Select Screen │ │ Low Power S0 Idle Capability [Enabled] │↑↓: Select Item │ │ 10sec Power Button OVR [Disabled] │Enter: Select │ │ EC Notification [Enabled] │+/-: Change Opt. │ │ EC CS Debug Light [Disabled] │F1: General Help │ │ EC Low Power Mode [Disabled] │F2: Previous Values │ │ Sensor Standby [Disabled] │F3: Optimized Defaults │ │ CS PL1 Limit [Enabled] │F4: Save & Exit │ │ CS PL1 Value 4500 │ESC: Exit │ │► PEP Constraints Configuration │ │ │ Lpit Recidency Counter [SLP S0] │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 PTID Support

Options: Disabled / Enabled

 PECI Access Method

Options: Direct I/O / ACPI

 Native PCIE Enable

Options: Disabled / Enabled

 Native ASPM

Options: Disabled / Enabled

 BDAT ACPI Table Support

Options: Disabled / Enabled

 Wake system from S5

Options: Disabled / Enabled

 Wake up hour

Options: 0..23

 Wake up minute

Options: 0..59

 Wake up second

Options: 0..59

 ACPI Debug

Options: Disabled / Enabled

 ACPI Memory Buffer Address

Options: none

Seite 56 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen  ACPI Low Power S0 Idle Capability

Options: Disabled / Enabled

 10sec Power Button OVR

Options: Disabled / Enabled

 EC Notification

Options: Disabled / Enabled

 EC CS Debug Light

Options: Disabled / Enabled

 EC Low Power Mode

Options: Disabled / Enabled

 Sensor Standby

Options: Disabled / Enabled

 CS PL1 Limit

Options: Disabled / Enabled

 PEP Constraints Configuration

Sub menu: see "PEP Constraints Configuration" (page 58)

 Lpit Recidency Counter

Options: SLP S0 / C10

 PCI Delay Optimization

Options: Disabled / Enabled

 ZpODD Support

Options: Disabled / Enabled

Beckhoff New Automation Technology CB1064-xxxx Seite 57

Kapitel: BIOS-Einstellungen Advanced

4.3.1.1 PEP Constraints Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PEP Constraints Configuration │Add CPU in PEP mitigation list │ │ │ │ │ PEP CPU [Enabled] │ │ │ PEP Graphics [Disabled] │ │ │ PEP ISP [Disabled] │ │ │ PEP SATA [Storage Controller] │ │ │ PEP UART [Enabled] │ │ │ PEP I2C0 [Enabled] │ │ │ PEP I2C1 [Enabled] │ │ │ PEP I2C2 [Enabled] │ │ │ PEP I2C3 [Enabled] │ │ │ PEP I2C4 [Enabled] │ │ │ PEP I2C5 [Enabled] │────────────────────────────────│ │ PEP SPI [Enabled] │→←: Select Screen │ │ PEP XHCI [Enabled] │↑↓: Select Item │ │ PEP Audio [Enabled] │Enter: Select │ │ PEP EMMC [Enabled] │+/-: Change Opt. │ │ PEP SDXC [Enabled] │F1: General Help │ │ [Enabled] │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 SPEP CPU

Options: Disabled / Enabled

 PEP Graphics

Options: Disabled / Enabled

 PEP ISP

Options: Disabled / Enabled

 PEP SATA

Options: No Constraint / Storage Controller

 PEP UART

Options: Disabled / Enabled

 PEP I2C0

Options: Disabled / Enabled

 PEP I2C1

Options: Disabled / Enabled

 PEP I2C2

Options: Disabled / Enabled

 PEP I2C3

Options: Disabled / Enabled

 PEP I2C4

Options: Disabled / Enabled

 PEP I2C5

Options: Disabled / Enabled

Seite 58 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen  PEP SPI

Options: Disabled / Enabled

 PEP XHCI

Options: Disabled / Enabled

 PEP Audio

Options: Disabled / Enabled

 PEP EMMC

Options: Disabled / Enabled

 PEP SDXC

Options: Disabled / Enabled

Beckhoff New Automation Technology CB1064-xxxx Seite 59

Kapitel: BIOS-Einstellungen Advanced

4.3.2 CPU Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ CPU Configuration ▲│Enable/Disable Software Guard │ │ █│Extensions (SGX) │ │ Type Intel(R) Core(TM) █│ │ │ i5-6400 CPU @ 2.70GHz █│ │ │ ID 0x506E3 █│ │ │ Speed 2700 MHz █│ │ │ L1 Data Cache 32 KB x 4 █│ │ │ L1 Instruction Cache 32 KB x 4 █│ │ │ L2 Cache 256 KB x 4 █│ │ │ L3 Cache 6 MB █│ │ │ L4 Cache N/A █│ │ │ VMX Supported █│ │ │ SMX/TXT Not Supported █│ │ │ █│ │ │ SW Guard Extensions (SGX) [Enabled] █│ │ │ Select Owner EPOCH input type [No Change in Owner █│────────────────────────────────│ │ EPOCHs] █│→←: Select Screen │ │ PRMRR Size [128MB] █│↑↓: Select Item │ │ CPU Flex Ratio Override [Disabled] █│Enter: Select │ │ CPU Flex Ratio Settings 27 ░│+/-: Change Opt. │ │ Hardware Prefetcher [Enabled] ░│F1: General Help │ │ Adjacent Cache Line Prefetch [Enabled] ░│F2: Previous Values │ │ Intel (VMX) Virtualization [Enabled] ░│F3: Optimized Defaults │ │ Technology ░│F4: Save & Exit │ │ PECI [Enabled] ░│ESC: Exit │ │ ░│ │ │ ░│ │ │ ▼│ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Type

Options: none

 ID

Options: none

 Speed

Options: none

 L1 Data Cache

Options: none

 L1 Instruction Cache

Options: none

 L2 Cache

Options: none

 L3 Cache

Options: none

 L4 Cache

Options: none

 VMX

Options: none

 SMX/TXT

Options: none

 SW Guard Extensions (SGX)

Options: Software Controlled / Enabled / Disabled

Seite 60 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen  Select Owner EPOCH input type

Options: No Change in Ownder EPOCHs / Change to New Random Owner EPOCHs / Manual

User Defined Owner EPOCHs

 PRMRR Size

Options: INVALID PRMRR / 32MB / 64MB / 128MB

 CPU Flex Ratio Override

Options: Disabled / Enabled

 CPU Flex Ratio Settings

Options: 0..63

 Hardware Prefetcher

Options: Disabled / Enabled

 Adjacent Cache Line Prefetch

Options: Disabled / Enabled

 Intel Virtualization Technology

Options: Enabled / Disabled

 PECI

Options: Enabled / Disabled

 Active Processor Cores

Options: All

 Hyper-threading

Options: Enabled / Disabled

 CPU AES

Options: Disabled / Enabled

 CPU - Power Management Control

Sub menu: see "CPU - Power Management Control" (page 62)

Beckhoff New Automation Technology CB1064-xxxx Seite 61

Kapitel: BIOS-Einstellungen Advanced

4.3.2.1 CPU - Power Management Control

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ CPU - Power Management Control ▲│Allows more than two frequency │ │ █│ranges to be supported. │ │ Intel(R) SpeedStep(tm) [Enabled] █│ │ │ Intel(R) Speed Shift Technology [Disabled] █│ │ │ Turbo Mode [Disabled] █│ │ │► View/Configure Turbo Options █│ │ │ █│ │ │ █│ │ │ █│ │ │ █│ │ │ █│ │ │ █│ │ │ █│ │ │ █│ │ │ █│ │ │ █│────────────────────────────────│ │ █│→←: Select Screen │ │ █│↑↓: Select Item │ │ █│Enter: Select │ │ ░│+/-: Change Opt. │ │ ░│F1: General Help │ │ ░│F2: Previous Values │ │ ░│F3: Optimized Defaults │ │ ░│F4: Save & Exit │ │ ░│ESC: Exit │ │ ░│ │ │ ░│ │ │ ▼│ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Intel(R) SpeedStep(tm)

Options: Disabled / Enabled

 Intel(R) Speed Shift Technology

Options: Disabled / Enabled

 Turbo Mode

Options: Disabled / Enabled

 View/Configure Turbo Options

Sub menu: see "View/Configure Turbo Options" (page 63)

Seite 62 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.2.1.1 View/Configure Turbo Options

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Current Turbo Settings │Enable/Disable Energy │ │ │Efficient P-state feature. │ │ Max Turbo Power Limit 4095.875 │When set to 0, will disable │ │ Min Turbo Power Limit 0.0 │access to │ │ Package TDP Limit 65.0 │ENERGY_PERFORMANCE_BIAS MSR │ │ Power Limit 1 65.0 │and CPUID Function 6 ECX[3] │ │ Power Limit 2 0.0 │will read 0 indicating no │ │ 1-core Turbo Ratio 33 │support for Energy Efficient │ │ 2-core Turbo Ratio 33 │policy setting. When set to 1 │ │ 3-core Turbo Ratio 32 │will enable access to │ │ 4-core Turbo Ratio 31 │ENERGY_PERFORMANCE_BIAS MSR │ │ │ │ │ Energy Efficient P-state [Enabled] │ │ │ Package Power Limit MSR Lock [Disabled] │ │ │ Energy Efficient Turbo [Disabled] │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Max Turbo Power Limit

Options: none

 Min Turbo Power Limit

Options: none

 Package TDP Limit

Options: none

 Power Limit 1

Options: none

 Power Limit 2

Options: none

 x-core Turbo Ratio

Options: none

 Energy Efficient P-state

Options: Enabled / Disabled

 Package Power Limit MSR Lock

Options: Disabled / Enabled

 Energy Efficient Turbo

Options: Enabled / Disabled

Beckhoff New Automation Technology CB1064-xxxx Seite 63

Kapitel: BIOS-Einstellungen Advanced

4.3.3 Intel(R) I210 Gigabit Network Connection

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │► NIC Configuration │Click to configure the network │ │ │device port. │ │ Blink LEDs 0 │ │ │ │ │ │ UEFI Driver Intel(R) PRO/1000 │ │ │ 7.3.20 PCI-E │ │ │ Adapter PBA 000300-000 │ │ │ Device Name Intel(R) I210 Gigabit │ │ │ Network Connection │ │ │ Chip Type Intel i210 │ │ │ PCI Device ID 1533 │ │ │ PCI Address 05:00:000 │ │ │ │────────────────────────────────│ │ Link Status [Disconnected] │→←: Select Screen │ │ │↑↓: Select Item │ │ MAC Address 00:01:05:2C:0B:3F │Enter: Select │ │ Virtual MAC Address 00:00:00:00:00:00 │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 NIC Configuration

Sub menu: see "NIC Configuration" (page 65)

 Blink LEDs

Options: none

 UEFI Driver

Options: none

 Adapter PBA

Options: none

 Device Name

Options: none

 Chip Type

Options: none

 PCI Device ID

Options: none

 PCI Address

Options: none

 Link Status

Options: none

 MAC Address

Options: none

 Virtual MAC Address

Options: none

Seite 64 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.3.1 NIC Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Link Speed [Auto Neg] │Specifies the port speed used │ │ Wake On LAN [Enabled] │for the selected boot protocol. │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Link Speed

Options: Auto Negotiated / 10Mbps Half / 10Mbps full / 100Mbps Half / 100Mbps Full

 Wake On LAN

Options: Enabled / Disabled

Beckhoff New Automation Technology CB1064-xxxx Seite 65

Kapitel: BIOS-Einstellungen Advanced

4.3.4 Intel(R) Ethernet Connection I219-LM

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PORT CONFIGURATION MENU │Click to configure the network │ │► NIC Configuration │device port. │ │ │ │ │ Blink LEDs 0 │ │ │ │ │ │ PORT CONFIGURATION INFORMATION │ │ │ UEFI Driver: Intel(R) Gigabit 0.0.166 │ │ │ Adapter PBA: FFFFFF-0FF │ │ │ Chip Type Intel PCH SPT │ │ │ PCI Device ID 15B7 │ │ │ PCI Address 00:1F:06 │ │ │ Link Status [Disconnected] │ │ │ MAC Address 00:01:05:2C:0B:3E │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 NIC Configuration

Sub menu: see "NIC Configuration" (page 65)

 Blink LEDs

Options: none

 UEFI Driver

Options: none

 Adapter PBA

Options: none

 Chip Type

Options: none

 PCI Device ID

Options: none

 PCI Address

Options: none

 Link Status

Options: none

 MAC Address

Options: none

Seite 66 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.5 Driver Health

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │► Intel(R) Gigabit 0.0.16 Healthy │Provides Health Status for the │ │► Intel(R) PRO/1000 7.3.20 PCI-E Healthy │Drivers/Controllers │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Intel(R) Gigabit 0.0.16

Sub menu: see "Intel(R) Gigabit 0.0.16" (page 67)

 Intel(R) PRO/1000 7.3.20 PCI-E

Sub menu: see "Intel(R) PRO/1000 7.3.20" (page 69)

Beckhoff New Automation Technology CB1064-xxxx Seite 67

Kapitel: BIOS-Einstellungen Advanced

4.3.5.1 Intel(R) Gigabit 0.0.16

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Controller 899de498 Child 0 Healthy │Provides Health Status for the │ │ │Drivers/Controllers │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Controller 899dd918 Child 0 Healthy

Options: none

Seite 68 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.5.2 Intel(R) PRO/1000 7.3.20

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Controller 899de498 Child 0 Healthy │Provides Health Status for the │ │ Intel(R) I210 Gigabit Network Connection Healthy │Drivers/Controllers │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Controller 899de498 Child 0 Healthy

Options: none

 Intel(R) I210 Gigabit Network Connection

Options: none

Beckhoff New Automation Technology CB1064-xxxx Seite 69

Kapitel: BIOS-Einstellungen Advanced

4.3.6 Trusted Computing

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ │Enables or Disables BIOS │ │ Configuration │support for security device. │ │ Security Device Support [Enable] │O.S. will not show Security │ │ NO Security Device Found │Device. TCG EFI protocol and │ │ │INT1A interface will not be │ │ │available. │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Security Device Support

Options: Enable / Disable

Seite 70 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.7 ACPI Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ ACPI Settings │Enables or Disables BIOS ACPI │ │ │Auto Configuration. │ │ Enable ACPI Auto Configuration [Disabled] │ │ │ │ │ │ Enable Hibernation [Enabled] │ │ │ ACPI Sleep State [S1 (CPU Stop Clock)] │ │ │ Lock Legacy Resources [Disabled] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Enable ACPI Auto Configuration

Options: Enabled / Disabled

 Enable Hibernation

Options: Enabled / Disabled

 ACPI Sleep State

Options: Suspend Disabled / S1 (CPU Stop Clock)

 Lock Legacy Resources

Options: Enabled / Disabled

Beckhoff New Automation Technology CB1064-xxxx Seite 71

Kapitel: BIOS-Einstellungen Advanced

4.3.8 SCH3114 Super IO Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ SCH3114 Super IO Configuration │Set Parameters of Serial Port │ │ │1 (COMA) │ │ Super IO Chip SCH3114 │ │ │► Serial Port 1 Configuration │ │ │► Serial Port 2 Configuration │ │ │► Serial Port 3 Configuration │ │ │► Serial Port 4 Configuration │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Serial Port X Configuration

Sub menu: see "Serial Port X Configuration" (page 73)

Seite 72 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.8.1 Serial Port X Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Serial Port 1 Configuration │Enable or Disable Serial Port │ │ │(COM) │ │ Serial Port [Enabled] │ │ │ Device Settings IO=3F8h; IRQ=4; │ │ │ │ │ │ Change Settings [Auto] │ │ │ Device Mode [Normal] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Serial Port

Options: Enabled / Disabled

 Device Settings

Options: none

 Change Settings

Options: Auto / IO=3F8h; IRQ=4 / IO=3F8h; IRQ=3, ...12 / IO=2F8h; IRQ=3, ...12 / IO=3E8h;

IRQ=3, ...12 / IO=2E8h; IRQ=3, ...12

 Device Mode

Options: Normal / High Speed

Beckhoff New Automation Technology CB1064-xxxx Seite 73

Kapitel: BIOS-Einstellungen Advanced

4.3.9 H/W Monitor

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PC Health Status │ │ │ │ │ │ CPU dig. : +23'C │ │ │ 1.05V : +0.98 V │ │ │ VCCCORE : +0.95 V │ │ │ 5V : +4.94 V │ │ │ 12V : +12.18V │ │ │ VBATT : +3.00 V │ │ │ 3.3V : +3.38 V │ │ │ SIO Temp : +27 'C │ │ │ 1.00V : +0.99 V │ │ │ Memory VDD : +1.18 V │ │ │ FAN 1 : N/A │────────────────────────────────│ │ FAN 2 : +2222 RPM │→←: Select Screen │ │ FAN 3 : N/A │↑↓: Select Item │ │ MB Temp : +27 'C │Enter: Select │ │ Memory Temp : +28 'C │+/-: Change Opt. │ │ PwrCtrlTemp : +28 'C │F1: General Help │ │ PwrCtrlVCC : +5.00 V │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 CPU dig.

Options: none

 1.05V

Options: none

 VCCCORE

Options: none

 5V

Options: none

 12V

Options: none

 VBATT

Options: none

 3.3V

Options: none

 SIO Temp

Options: none

 1.00V

Options: none

 Memory VDD

Options: none

 FAN 1

Options: none

Seite 74 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen  FAN 2

Options: none

 FAN 3

Options: none

 MB Temp

Options: none

 Memory Temp

Options: none

 PwrCtrlTemp

Options: none

 PwrCtrlVCC

Options: none

Beckhoff New Automation Technology CB1064-xxxx Seite 75

Kapitel: BIOS-Einstellungen Advanced

4.3.10 Serial Port Console Redirection

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ │Console Redirection Enable or │ │ COM0 │Disable. │ │ Console Redirection [Disabled] │ │ │► Console Redirection Settings │ │ │ │ │ │ COM1 │ │ │ Console Redirection [Disabled] │ │ │► Console Redirection Settings │ │ │ │ │ │ COM2 │ │ │ Console Redirection [Disabled] │ │ │► Console Redirection Settings │ │ │ │────────────────────────────────│ │ COM3 │→←: Select Screen │ │ Console Redirection [Disabled] │↑↓: Select Item │ │► Console Redirection Settings │Enter: Select │ │ │+/-: Change Opt. │ │ COM4(Pci Bus0,Dev0,Func0) (Disabled) │F1: General Help │ │ Console Redirection Port Is Disabled │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Console Redirection

Options: Enabled / Disabled

 Console Redirection Settings

Sub menu: see "Console Redirection Settings" (page 77)

Seite 76 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.10.1 Console Redirection Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ COM0 │Emulation: ANSI: Extended │ │ Console Redirection Settings │ASCII char set. VT100: ASCII │ │ │char set. VT100+: Extends │ │ Terminal Type [VT-UTF8] │VT100 to support color, │ │ Bits per second [115200] │function keys, etc. VT-UTF8: │ │ Data Bits [8] │Uses UTF8 encoding to map │ │ Parity [None] │Unicode chars onto 1 or more │ │ Stop Bits [1] │bytes. │ │ Flow Control [None] │ │ │ VT-UTF8 Combo Key Support [Enabled] │ │ │ Recorder Mode [Disabled] │ │ │ Resolution 100x31 [Enabled] │ │ │ Legacy OS Redirection Resolution [80x24] │────────────────────────────────│ │ Putty KeyPad [VT100] │→←: Select Screen │ │ Redirection After BIOS POST [Always Enable] │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Terminal Type

Options: VT100 / VT100+ / VT-UTF8 / ANSI

 Bits per second

Options: 9600 / 19200 / 38400 / 57600 / 115200

 Data Bits

Options: 7 / 8

 Parity

Options: None / Even / Odd / Mark / Space

 Stop Bits

Options: 1 / 2

 Flow Control

Options: None / Hardware RTS/CTS

 VT-UTF8 Combo Key Support

Options: Disabled / Enabled

 Recorder Mode

Options: Disabled / Enabled

 Resolution 100x31

Options: Disabled / Enabled

 Legacy OS Redirection Resolution

Options: 80x24 / 80x25

 Putty KeyPad

Options: VT100 / LINUX / XTERMR6 / SCO / ESCN / VT400

Beckhoff New Automation Technology CB1064-xxxx Seite 77

Kapitel: BIOS-Einstellungen Advanced  Redirection After BIOS POST

Options: Always Enable / BootLoader

Seite 78 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.11 PCI Subsystem Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCI Bus Driver Version A5.01.12 │Value to be programmed into │ │ │PCI Latency Timer Register. │ │ PCI Devices Common Settings: │ │ │ PCI Latency Timer [32 PCI Bus Clocks] │ │ │ PCI-X Latency Timer [64 PCI Bus Clocks] │ │ │ VGA Palette Snoop [Disabled] │ │ │ PERR# Generation [Disabled] │ │ │ SERR# Generation [Disabled] │ │ │ Above 4G Decoding [Disabled] │ │ │ │ │ │ │ │ │► PCI Hot-Plug Settings │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 PCI Latency Timer

Options: 32, 64,...224, 248 PCI Bus Clocks

 PCI-X Latency Timer

Options: 32, 64,...224, 248 PCI Bus Clocks

 VGA Palette Snoop

Options: Disabled / Enabled

 PERR# Generation

Options: Disabled / Enabled

 SERR# Generation

Options: Disabled / Enabled

 Above 4G Decoding

Options: Enabled / Disabled

 PCI Hot-Plug Settings

Sub menu: see "PCI Hot-Plug Settings" (page 80)

Beckhoff New Automation Technology CB1064-xxxx Seite 79

Kapitel: BIOS-Einstellungen Advanced

4.3.11.1 PCI Hot-Plug Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PCI Hot-Plug Settings │If ENABLED allows BIOS build │ │ │in Hot-Plug supportxed │ │ BIOS Hot-Plug Support [Enabled] │Ordering │ │ │ │ │ PCI Buses Padding [1] │ │ │ I/O Resources Padding [4 K] │ │ │ MMIO 32 bit Resources Padding [16 M] │ │ │ PFMMIO 32 bit Resources Padding [16 M] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 BIOS Hot-Plug Support

Options: Enabled / Disabled

 PCI Buses Padding

Options: Disabled / 1 / 2 / 3 / 3 / 5

 I/O Resources Padding

Options: Disabled / 4 K / 8 K / 16 K / 32 K

 MMIO 32 bit Resources

Options: Disabled / 4 K / 8 K / 16 K / 32 K

 PFMMIO 32 bit Resources

Options: Disabled / 1 M / 2 M / 4 M / 8 M / 16 M / 32 M / 64 M / 64 M

Seite 80 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.12 Network Stack Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Network Stack [Enabled] │Enable/Disable UEFI Network │ │ IPv4 PXE Support [Disabled] │Stack │ │ IPv4 HTTP Support [Disabled] │ │ │ IPv6 PXE Support [Disabled] │ │ │ IPv6 HTTP Support [Disabled] │ │ │ IPv6 Configuration Policy [Automatic] │ │ │ PXE boot wait time 0 │ │ │ Media detect count 1 │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Network stack

Options: Disabled / Enabled

 IPv4 PXE Support

Options: Disabled / Enabled

 IPv4 HTTP Support

Options: Disabled / Enabled

 IPv6 PXE Support

Options: Disabled / Enabled

 IPv6 HTTP Support

Options: Disabled / Enabled

 IPv6 Configuration Policy

Options: Automatic / Manual

 PXE boot wait time

Options: 0..5

 Media detect count

Options: 0..50

Beckhoff New Automation Technology CB1064-xxxx Seite 81

Kapitel: BIOS-Einstellungen Advanced

4.3.13 Power Controller Options

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Bootloader Version 1.00-31 │Select Power line for external │ │ Firmware Version 1.01-00 │USB devices, if powered-down │ │ Mainboard Serial No 15559716370007 │ │ │ Mainboard Prod. Date (Week.Year) 51.16 │ │ │ Mainboard BootCount 322 │ │ │ Mainboard Operation Time 86041min (1434h) │ │ │ Voltage (Min/Max) 4.60V / 5.20V │ │ │ Temperature (Min/Max) -35'C / 99'C │ │ │ │ │ │ ext. USB-Port Voltage [Off in S3-5] │ │ │ int. USB-Port Voltage [Off in S3-5] │ │ │ │ │ │ WDT OSBoot Timeout [Disabled] │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Bootloader Version

Options: none

 Firmware Version

Options: none

 Mainboard Serial No

Options: none

 Mainboard Prod. Date (Week.Year)

Options: none

 Mainboard Boot Count

Options: none

 Mainboard Operation Time

Options: none

 Voltage (Min/Max)

Options: none

 Temperature (Min/Max)

Options: none

 ext. USB-Port Voltage

Options: Off in S3-5 / by SVCC

 int. USB-Port Voltage

Options: Off in S3-5 / by SVCC

 WatchDogTimer Mode

Options: Normal Mode / Compatibility Mode

Seite 82 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen  WDT OSBoot Timeout

Options: Disabled / 45 Seconds ... 255 Seconds

Beckhoff New Automation Technology CB1064-xxxx Seite 83

Kapitel: BIOS-Einstellungen Advanced

4.3.14 Compatibility Support Module Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Compatibility Support Module Configuration │Determines OpROM execution │ │ │policy for devices other than │ │ CSM Support [Enabled] │Network, Storage, or Video │ │ │ │ │ CSM16 Module Version 07.80 │ │ │ │ │ │ GateA20 Active [Upon Request] │ │ │ Option ROM Messages [Force BIOS] │ │ │ INT19 Trap Response [Immediate] │ │ │ │ │ │ Boot option filter [UEFI and Legacy] │ │ │ │ │ │ Option ROM execution │────────────────────────────────│ │ Network [Legacy] │→←: Select Screen │ │ Storage [Legacy] │↑↓: Select Item │ │ Video [Legacy] │Enter: Select │ │ Other PCI devices [UEFI] │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 CSM Support

Options: Disabled / Enabled

 CSM16 Module Version

Options: none

 GateA20 Active

Options: Upon Request / Always

 Option ROM Messages

Options: Force BIOS / Keep Current

 INT9 Trap Response

Options: Immediate / Postponed

 Boot option filter

Options: UEFI and Legacy / Legacy only / UEFI only

 Network

Options: Do not launch / UEFI only / Legacy only

 Storage

Options: Do not launch / UEFI only / Legacy only

 Video

Options: Do not launch / UEFI only / Legacy only

 Other PCI devices

Options: Do not launch / UEFI / Legacy

Seite 84 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.15 NVMe Controller and Drive Information

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ NVMe controller and Drive information │ │ │ │ │ │ No NVMe Device Found │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 NVMe controller and Drive information

Options: none

Beckhoff New Automation Technology CB1064-xxxx Seite 85

Kapitel: BIOS-Einstellungen Advanced

4.3.16 USB Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ USB Configuration │Enables Legacy USB support. │ │ │AUTO option disables legacy │ │ USB Module Version 19 │support if no USB devices are │ │ │connected. DISABLE option will │ │ USB Controllers: │keep USB devices available │ │ 1 XHCI │only for EFI applications. │ │ USB Devices: │ │ │ 1 Keyboard │ │ │ │ │ │ Legacy USB Support [Enabled] │ │ │ XHCI Hand-off [Enabled] │ │ │ USB Mass Storage Driver Support [Enabled] │ │ │ │────────────────────────────────│ │ USB hardware delays and time-outs: │→←: Select Screen │ │ USB transfer time-out [20 sec] │↑↓: Select Item │ │ Device reset time-out [20 sec] │Enter: Select │ │ Device power-up delay [Manual] │+/-: Change Opt. │ │ Device power-up delay in seconds 5 │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 USB Module Version

Options: none

 USB Devices

Options: none

 USB Controllers

Options: none

 Legacy USB Support

Options: Enabled / Disabled / Auto

 XHCI Hand-off

Options: Enabled / Disabled

 USB Mass Storage Driver Support

Options: Disabled / Enabled

 USB transfer time-out

Options: 5 sec / 10 sec / 20 sec

 USB transfer time-out

Options: 10 sec / 20 sec / 30 sec / 40 sec

 Device power-up delay

Options: Auto / Manual

 Device power-up delay in seconds

Options: 1..40

Seite 86 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.17 SATA and RST Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ SATA And RST Configuration ▲│Enable or disable SATA Device. │ │ █│ │ │ SATA Controller(s) [Enabled] █│ │ │ SATA Mode Selection [Intel RST Premium] █│ │ │ SATA Test Mode [Disabled] █│ │ │ RAID Device ID [Client] █│ │ │► Software Feature Mask Configuration █│ │ │ Aggressive LPM Support [Enabled] █│ │ │ SATA Controller Speed [Default] █│ │ │ █│ │ │ Serial ATA Port 0 Empty █│ │ │ Software Preserve Unknown █│ │ │ Port 0 [Enabled] █│────────────────────────────────│ │ Hot Plug [Enabled] ░│→←: Select Screen │ │ Configured as eSATA Hot Plug supported ░│↑↓: Select Item n │ │ Spin Up Device [Disabled] ░│Enter: Select │ │ SATA Device Type [Hard Disk Drive] ░│+/-: Change Opt. │ │ Topology [Unknown] ░│F1: General Help │ │ SATA Port 0 DevSlp [Disabled] ░│F2: Previous Values │ │ DITO Configuration [Disabled] ░│F3: Optimized Defaults │ │ DITO Value 625 ░│F4: Save & Exit │ │ DM Value 15 ░│ESC: Exit │ │ Serial ATA Port 1 Empty ░│ │ │ Software Preserve Unknown ░│ │ │ Port 1 [Enabled] ░│ │ │ ░│ │ │ ▼│ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 SATA Controller(s)

Options: Enabled / Disabled

 SATA Mode Selection

Options: IDE / AHCI / RAID

 SATA Test Mode

Options: Enabled / Disabled

 RAID Device ID

Options: Client / Alternate

 Software Feature Mask Configuration

Sub menu: see "Software Feature Mask Configuration" (page 89)

 Aggressive LPM Support

Options: Enabled / Disabled

 SATA Controller Speed

Options: Default / Gen1 / Gen2 / Gen3

 Serial ATA Port X

Options: none

 Software Preserve

Options: none

 Port X

Options: Enabled / Disabled

 Hot Plug

Options: Enabled / Disabled

Beckhoff New Automation Technology CB1064-xxxx Seite 87

Kapitel: BIOS-Einstellungen Advanced  Configured as eSATA

Options: none

 Spin Up Device

Options: Enabled / Disabled

 SATA Device Type

Options: Hard Disk Drive / Solid State Drive

 Topology

Options: Unknown / ISATA / Direct Connect / Flex / M2

 SATA Port X DevSlp

Options: Disabled / Enabled

 DITO Configuration

Options: Disabled / Enabled

 DITO Value

Options: 0..1023

 DM Value

Options: 0..15

Seite 88 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.17.1 Software Feature Mask Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Software Feature Mask Configuration │If enabled, indicates that the │ │ │HDD password unlock in the OS │ │ HDD Unlock [Enabled] │is enabled. │ │ LED Locate [Enabled] │ │ │ RAID0 [Enabled] │ │ │ RAID1 [Enabled] │ │ │ RAID10 [Enabled] │ │ │ RAID5 [Enabled] │ │ │ Intel Rapid Recovery Technolgy [Enabled] │ │ │ OROM UI and BANNER [Enabled] │ │ │ IRRT Only on eSATA [Enabled] │ │ │ Smart Response Technology [Enabled] │ │ │ OROM UI Normal Delay [2 secs] │────────────────────────────────│ │ RST Force Form [Enabled] │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 HDD Unlock

Options: Enabled / Disabled

 LED Locate

Options: Enabled / Disabled

 RAID0

Options: Enabled / Disabled

 RAID1

Options: Enabled / Disabled

 RAID10

Options: Enabled / Disabled

 RAID5

Options: Enabled / Disabled

 Intel Rapid Recovery Technology

Options: Enabled / Disabled

 OROM UI and BANNER

Options: Enabled / Disabled

 IRRT Only on eSATA

Options: Enabled / Disabled

 Smart Response Technology

Options: Enabled / Disabled

 OROM UI Normal Delay

Options: 2 / 4 / 6 / 8 Seconds

Beckhoff New Automation Technology CB1064-xxxx Seite 89

Kapitel: BIOS-Einstellungen Advanced  RST Force Form

Options: Enabled / Disabled

Seite 90 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.18 AMT Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ ASF Support [Enabled] │Enable/Disable of AMT USB │ │ │Provisioning. │ │ USB Provisioning of AMT [Disabled] │ │ │► CIRA Configuration │ │ │► ASF Configuration │ │ │► Secure Erase Configuration │ │ │► OEM Flags Settings │ │ │► MEBx Resolution Settings │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 ASF Support

Options: Enabled / Disabled

 AMT Provisioning of AMT

Options: Enabled / Disabled

 CIRA Configuration

Sub menu: see "CIRA Configuration" (page 91)

 ASF Configuration

Sub menu: see "ASF Configuration" (page 93)

 Secure Erase Configuration

Sub menu: see "Secure Erase Configuration" (page 94)

 OEM Flags Settings

Sub menu: see "OEM Flags Configuration" (page 95)

 MEBx Resolution Settings

Sub menu: see "MEBx Resolution Settings" (page 96)

Beckhoff New Automation Technology CB1064-xxxx Seite 91

Kapitel: BIOS-Einstellungen Advanced

4.3.18.1 CIRA Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Activate Remote Assistance Process [Disabled] │Enable/Disable of AMT USB │ │ CIRA Timeout 0 │Provisioning. │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Activate Remote Assistance Process

Options: Enabled / Disabled

 CIRA Timeout

Options: 0..255

Seite 92 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.18.2 ASF Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ PET Progress [Enabled] │Enable/Disable of AMT USB │ │ WatchDog [Disabled] │Provisioning. │ │ OS Timer 0 │ │ │ BIOS Timer 0 │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 PET Progress

Options: Enabled / Disabled

 WatchDog

Options: Enabled / Disabled

 OS Timer

Options: 0..65535

 BIOS Timer

Options: 0..65535

Beckhoff New Automation Technology CB1064-xxxx Seite 93

Kapitel: BIOS-Einstellungen Advanced

4.3.18.3 Secure Erase Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Secure Erase Mode [Simulated] │Change Secure Erase module │ │ Force Secure Erase [Disabled] │behavior: │ │ │Simulated: Performs SE flow │ │ │without erasing SSD │ │ │Real: Erase SSD. │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Secure Erase mode

Options: Simulated / Real

 Force Secure Erase

Options: Disabled / Enabled

Seite 94 Beckhoff New Automation Technology CB1064-xxxx

Advanced Kapitel: BIOS-Einstellungen

4.3.18.4 OEM Flags Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ MEBx hotkey Pressed [Simulated] │Change Secure Erase module │ │ MEBx Selection Screen [Disabled] │behavior: │ │ Hide Unconfigure ME Confirmation [Disabled] │Simulated: Performs SE flow │ │ Prompt │without erasing SSD │ │ MEBx OEM Debug Menu Enable [Disabled] │Real: Erase SSD. │ │ Unconfigure ME [Disabled] │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 MEBx Selection

Options: Disabled / Enabled

 MEBx Selection Screen

Options: Disabled / Enabled

 Hide Unconfigure ME Confirmation Prompt

Options: Disabled / Enabled

 MEBx OEM Debug Menu Enable

Options: Disabled / Enabled

 Unconfigure ME

Options: Disabled / Enabled

Beckhoff New Automation Technology CB1064-xxxx Seite 95

Kapitel: BIOS-Einstellungen Advanced

4.3.18.5 MEBx Resolution Settings

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Non-UI Mode Resolution [Auto] │Change Secure Erase module │ │ UI Mode Resolution [Auto] │behavior: │ │ Graphics Mode Resolution [Auto] │Simulated: Performs SE flow │ │ │without erasing SSD │ │ │Real: Erase SSD. │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Non-UI Mode Resolution

Options: Auto / 80x25 / 100x31

 UI Mode Resolution

Options: Auto / 80x25 / 100x31

 Graphics Mode Resolution

Options: Auto / 640x480 / 800x600 / 1024x768

Seite 96 Beckhoff New Automation Technology CB1064-xxxx

Chipset Kapitel: BIOS-Einstellungen

4.4 Chipset

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │► System Agent (SA) Configuration │System Agent (SA) Parameters │ │► PCH-IO Configuration │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │────────────────────────────────│ │ │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 System Agent (SA) Configuration

Sub menu: see "System Agent (SA) Configuration" (page 98)

 PCH-IO Configuration

Sub menu: see "PCH-IO Configuration" (page 110)

Beckhoff New Automation Technology CB1064-xxxx Seite 97

Kapitel: BIOS-Einstellungen Chipset

4.4.1 System Agent (SA) Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ System Agent (SA) Configuration │Graphics Configuration │ │ │ │ │ SA PCIe Code Version 1.7.0.0 │ │ │ VT-d Supported │ │ │ │ │ │► Graphics Configuration │ │ │► PEG Port Configuration │ │ │ │ │ │ VT-d [Enabled] │ │ │ CHAP Device (B0:D7:F0) [Disabled] │ │ │ Thermal Device (B0:D4:F0) [Disabled] │ │ │ GMM Device (B0:D8:F0) [Enabled] │ │ │ CRID Support [Disabled] │────────────────────────────────│ │ Above 4GB MMIO BIOS assignment [Disabled] │→←: Select Screen │ │ │↑↓: Select Item │ │ │Enter: Select │ │ │+/-: Change Opt. │ │ │F1: General Help │ │ │F2: Previous Values │ │ │F3: Optimized Defaults │ │ │F4: Save & Exit │ │ │ESC: Exit │ │ │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Graphics Configuration

Sub menu: see "Graphics Configuration" (page 99)

 PEG Port Configuration

Sub menu: see "PEG Port Configuration" (page 103)

 VT-d

Options: Disabled / Enabled

 CHAP Device (B0:D7:F0)

Options: Disabled / Enabled

 Thermal Device (B0:D4:F0)

Options: Disabled / Enabled

 GMM Device (B0:D8:F0)

Options: Disabled / Enabled

 CRID Support

Options: Disabled / Enabled

 Above 4GB MMIO BIOS assignment

Options: Disabled / Enabled

Seite 98 Beckhoff New Automation Technology CB1064-xxxx

Chipset Kapitel: BIOS-Einstellungen

4.4.1.1 Graphics Configuration

┌─────────────────────────────────────────────────────────────────┬────────────────────────────────┐ │ Graphics Configuration │Graphics turbo IMON current │ │ │values supported (14-31) │ │ Graphics Turbo IMON Current 31 │ │ │ Skip Scanning of External Gfx Card [Disabled] │ │ │ │ │ │ Primary Display [Auto] │ │ │ Select PCIE Card [Auto] │ │ │► External Gfx Card Primary Display Configuration │ │ │ Internal Graphics [Auto] │ │ │ GTT Size [8MB] │ │ │ Aperture Size [256MB] │ │ │ DVMT Pre-Allocated [32M] │ │ │ DVMT Total Gfx Mem [256M] │────────────────────────────────│ │ Gfx Low Power Mode [Enabled] │→←: Select Screen │ │ VDD Enable [Enabled] │↑↓: Select Item │ │ HDCP Support [Enabled] │Enter: Select │ │ Algorithm [One-time] │+/-: Change Opt. │ │ PM Support [Enabled] │F1: General Help │ │ PAVP Enable [Enabled] │F2: Previous Values │ │ Cdynmax Clamping Enable [Enabled] │F3: Optimized Defaults │ │ Cd Clock Frequency [675 Mhz] │F4: Save & Exit │ │ IUER Button Enable [Disabled] │ESC: Exit │ │► LCD Control │ │ │ │ │ │ │ │ │ │ │ └─────────────────────────────────────────────────────────────────┴────────────────────────────────┘

 Graphics Turbo IMON Current

Options: 14...31

 Skip scanning of external Gfx Card

Options: Disabled / Enabled

 Primary Display

Options: Auto / IGFX / PEG / PCI

 Select PCIE Card

Options: Auto / Elk Creek 4 / PEG Eval

 External Gfx Card Primary Display Configuration

Sub menu: see "External Gfx Card Primary Display Configuration" (page 101)

 Internal Graphics

Options: Auto / Disabled / Enabled

 GTT Size

Options: 1MB / 2MB

 Aperture Size

Options: 128MB / 256MB / 512MB

 DVMT Pre-Allocated

Options: 32M / 64M ... 480M / 512M / 1024M

 DVMT Total Gfx Mem

Options: 128M / 256M / MAX

 Gfx Low Power Mode

Options: Disabled / Enabled

Beckhoff New Automation Technology CB1064-xxxx Seite 99

Kapitel: BIOS-Einstellungen Chipset  VDD Enable

Options: Disabled / Enabled

 HDCP Support

Options: Disabled / Enabled

 Algorithm

Options: One-time / Periodic

 PM Support

Options: Disabled / Enabled

 PAVP Enable

Options: Disabled / Enabled

 Cdynmax Clamping Enable

Options: Disabled / Enabled

 Cd Clock Frequency

Options: 337.5 Mhz / 450 Mhz / 540 Mhz / 675 Mhz

 IUER Button Enable

Options: Enabled / Disabled

 LCD Control

Sub menu: see "LCD Control" (page 102)

Seite 100 Beckhoff New Automation Technology CB1064-xxxx

Beckhoff CB1064 Manual 1.2

Specifications and Main Features

Frequently Asked Questions

User Manual