Atlas WMA10-23, WMA, WMA16-23, WMA12-23, WMA35-23 Manual

...

0 (0)

WMA Cabinets

Wall Mounted Cabinet Series

1/10

CAUTION

1. Read these instructions. Follow all instructions. Keep these instructions. Heed all warnings.

2. Use eye protection and protective gloves while unpacking the cabinet.

3. Make sure there are enough people to help safely unload and install the system. Empty rack cabinets alone may weigh up to 200 lbs. Moving rack

cabinets can present dangers to other personnel and the incorporated equipment.

©2018 Atlas Sound L.P. All rights reserved. Atlas Sound is a trademark of Atlas Sound L.P. All other trademarks are the property of their respective owners. All specs are subject to change without notice. ATS004389 P/N 490240 RevE 10/18

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333 FAX: (800) 765-3435

AtlasSound.com

2/10

WMA Cabinets

Wall Mounted Cabinet Series

1. Important Safety Instructions

a. These cabinet products are initially provided without installed electrical equipment and therefore are not liable for any hazards/damage

incurred by not following proper safety procedures. Installation, operation, and maintenance personnel should always follow the procedures

outlined in the National Electrical Code and any other regulations mandated by the local authorities having jurisdiction over the installation.

b. The cabinet is designed for installation and use in areas designated as "Restricted Access Location" only.

c. The installation of the cabinet is to be made by qualified service personnel in accordance with local building codes, the Installation

Instructions, and the National Electrical Code.

d. The Listing Mark on the product does not cover any of the electrical equipment, AC or DC, that may be installed in the field. The Product is

not intended to contain or house any open-frame, high-voltage electrical components like open switches, supplementary protectors, circuit

breakers, fuses, relays, etc.

e. The cabinet is intended to house audio, video, information technology, and telecommunications equipment provided with their own fire,

electrical, and mechanical enclosures.

f. Product is evaluated for use in environmentally controlled indoor areas only. The product is not to be used outdoors, in industrial or harsh

environments, or in plenum spaces.

g. The frame of the product may support a maximum load:

Model Maximum Load

WMA10-23 200 lbs

WMA12-23 200 lbs

WMA16-23 200 lbs

WMA24-23 300 lbs

WMA35-23 300 lbs

h. Use eye protection and protective gloves while unpacking and installing the cabinet.

i. Ensure adequate manpower is available to safely unload and install the product.

2. Introduction

a. This rack cabinet system is used to house rack-mounted equipment for use in audio, video, and/or data applications for network, voice,

data and video modules/devices and their associated cabling. Final equipment installer must follow individual equipment manufacturer’s

installation instructions.

b. These are wall mounted rack cabinet systems.

c. The unit’s back box is packaged separately and may be shipped to the job site where it may be installed.

d. The center section of the rack cabinet may be loaded with equipment and attached to the back box at any time. In addition, the center

section may be mounted to open in either a left or right swing-out motion.

e. The rack cabinet is provided with 1 pair of adjustable rails.

f. There is a 3RU panel in the top and bottom of the center section. These panels may be removed and replaced by other accessories such as

perforated vent panels and/or fan panels.

g. Maximum capacity of the rack cabinet is provided in the Important Safety Instructions section.

h. These cabinets all comply to U.S. and Canadian (Bi-National) Standard for Safety of Information Technology Equipment, CAN/CSA-C22.2 No.

60950-1-07, Second Edition, date March 27, 2007, UL 2416, Outline of Investigation for Audio/Video, Information and Communication

Technology Equipment Cabinet, Enclosure and Rack Systems.", Issue 2, dated 2013-07-12.

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333 FAX: (800) 765-3435

AtlasSound.com

3/10

WMA Cabinets

Wall Mounted Cabinet Series

3. Required Tools

a. Razor Knife

b. Claw Hammer or Staple Remover

c. #2 Phillips Cross-Drive Screw Driver (Manual or Auto)

e. Tape Measure (optional)

f. If installing Front Door (purchased separately) -

4. Shipping Packaging Removable

CAUTION: Ensure adequate manpower is available to help safely unload and install the system. Empty cabinets alone may weigh up to 200 lbs.

Moving rack cabinets can present dangers to both personnel and installed equipment.

CAUTION: Use eye protection and protective gloves while unpacking and installing the cabinet.

a. The cabinet will be shipped on a wood pallet. The back box and center section are in separate cartons. Select an unpacking location with

adequate surrounding space for the unloading process. In addition, plan a smooth and unobstructed route to the installation site. Low

obstructions, narrow pathways, doorsills, carpet, etc. can hinder movement. Use care when navigating obstacles. Always push from the

cabinet front or back surfaces, never pull a cabinet or push from the cabinet sides.

b. Carefully cut and remove shipping straps holding cabinet to shipping pallet.

c. Remove shrink plastic and shipping materials.

d. The back box will be found in the narrower carton. If required, this carton can be sent to a job site for mounting on a wall.

e. Use a claw hammer or staple remover to remove staples from the carton end.

f. Carefully flip carton on to the open end and pull carton off back box.

g. In most cases, the center section will be packaged in a larger carton. Use the same tools and procedure to remove the carton off the center

section.

h. Carefully cut and remove the hardware bag containing door keys, rack rail hardware, top hardware and set aside for future use.

⁄8" Hex Socket Driver

⁄32 L-Shaped Hex Driver Key

5. Cabinet Orientation

a. The back box is symmetrical. However, the knockout panel

must be mounted horizontally. In addition, the back face of this

unit is mostly solid except for the wiring access window and

wall mount holes.

b. The front of the cabinet includes the presence of ten (10)

groups of vents. In addition, there will be four (4) pairs of

threaded holes (covered with plastic plugs) to be used for

mounting accessory front doors.

c. The bottom and top of the center section has a removable 3RU

sold panel. This panel may be replaced with other accessories.

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333 FAX: (800) 765-3435

AtlasSound.com

+ 7 hidden pages